openwrt/openwrt.git
4 months agokernel: Include xt_MASQUERADE for kernel 5.2 and later
Koen Vandeputte [Sun, 23 Feb 2020 14:30:37 +0000 (15:30 +0100)]
kernel: Include xt_MASQUERADE for kernel 5.2 and later

Instead of ip6t_MASQUERADE, include xt_MASQUERADE on kernel >= 5.2.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
4 months agokernel: mode_beet mode_transport mode_tunnel xfram modules
Koen Vandeputte [Sun, 23 Feb 2020 14:28:15 +0000 (15:28 +0100)]
kernel: mode_beet mode_transport mode_tunnel xfram modules

This adds the new xfrm4_mode_beet, xfrm4_mode_transport,
xfrm4_mode_tunnel and their IPv6 versions on kernel 5.4. These modules
were newly added in kernel 5.2.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
4 months agox86: Update configuration
Hauke Mehrtens [Sun, 23 Feb 2020 15:46:41 +0000 (16:46 +0100)]
x86: Update configuration

The configuration was refreshed and KERNEL_TESTING_PATCHVER was set to
make it easy to compile for kernel 5.4.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4 months agox86: Refresh patches on kernel 5.4
Hauke Mehrtens [Sun, 23 Feb 2020 13:58:32 +0000 (14:58 +0100)]
x86: Refresh patches on kernel 5.4

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4 months agox86: copy kernel patches from 4.19 to 5.4
Hauke Mehrtens [Sun, 23 Feb 2020 13:55:25 +0000 (14:55 +0100)]
x86: copy kernel patches from 4.19 to 5.4

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4 months agokernel: add support for kernel 5.4
Koen Vandeputte [Mon, 25 Nov 2019 15:08:31 +0000 (16:08 +0100)]
kernel: add support for kernel 5.4

The following patches were removed because they are integrated in the upstream kernel 5.4:
 * backport-5.4/047-v4.21-mtd-keep-original-flags-for-every-struct-mtd_info.patch
 * backport-5.4/048-v4.21-mtd-improve-calculating-partition-boundaries-when-ch.patch
 * backport-5.4/080-v5.1-0001-bcma-keep-a-direct-pointer-to-the-struct-device.patch
 * backport-5.4/080-v5.1-0002-bcma-use-dev_-printing-functions.patch
 * backport-5.4/095-Allow-class-e-address-assignment-via-ifconfig-ioctl.patch
 * backport-5.4/101-arm-cns3xxx-use-actual-size-reads-for-PCIe.patch
 * backport-5.4/200-v5.2-usb-dwc2-Set-lpm-mode-parameters-depend-on-HW-configuration.patch
 * backport-5.4/210-arm64-sve-Disentangle-uapi-asm-ptrace.h-from-uapi-as.patch
 * backport-5.4/380-v5.3-net-sched-Introduce-act_ctinfo-action.patch
 * backport-5.4/450-v5.0-mtd-spinand-winbond-Add-support-for-W25N01GV.patch
 * backport-5.4/451-v5.0-mtd-spinand-Add-initial-support-for-Toshiba-TC58CVG2.patch
 * backport-5.4/452-v5.0-mtd-spinand-add-support-for-GigaDevice-GD5FxGQ4xA.patch
 * backport-5.4/455-v5.1-mtd-spinand-Add-support-for-all-Toshiba-Memory-produ.patch
 * backport-5.4/456-v5.1-mtd-spinand-Add-support-for-GigaDevice-GD5F1GQ4UExxG.patch
 * backport-5.4/460-v5.0-mtd-spi-nor-Add-support-for-mx25u12835f.patch
 * backport-5.4/460-v5.3-mtd-spinand-Define-macros-for-page-read-ops-with-thr.patch
 * backport-5.4/461-v5.3-mtd-spinand-Add-support-for-two-byte-device-IDs.patch
 * backport-5.4/462-v5.3-mtd-spinand-Add-support-for-GigaDevice-GD5F1GQ4UFxxG.patch
 * backport-5.4/463-v5.3-mtd-spinand-Add-initial-support-for-Paragon-PN26G0xA.patch
 * backport-5.4/700-v5.1-net-phylink-only-call-mac_config-during-resolve-when.patch
 * backport-5.4/701-v5.2-net-phylink-ensure-inband-AN-works-correctly.patch
 * backport-5.4/702-v4.20-net-ethernet-Add-helper-for-MACs-which-support-asym-.patch
 * backport-5.4/703-v4.20-net-ethernet-Add-helper-for-set_pauseparam-for-Asym-.patch
 * backport-5.4/704-v4.20-net-phy-Stop-with-excessive-soft-reset.patch
 * backport-5.4/705-v5.1-net-phy-provide-full-set-of-accessor-functions-to-MM.patch
 * backport-5.4/706-v5.1-net-phy-add-register-modifying-helpers-returning-1-o.patch
 * backport-5.4/707-v5.1-net-phy-add-genphy_c45_check_and_restart_aneg.patch
 * backport-5.4/708-v5.3-net-phylink-remove-netdev-from-phylink-mii-ioctl-emu.patch
 * backport-5.4/709-v5.3-net-phylink-support-for-link-gpio-interrupt.patch
 * backport-5.4/710-v5.3-net-phy-allow-Clause-45-access-via-mii-ioctl.patch
 * backport-5.4/711-v5.3-net-sfp-add-mandatory-attach-detach-methods-for-sfp-.patch
 * backport-5.4/712-v5.3-net-sfp-remove-sfp-bus-use-of-netdevs.patch
 * backport-5.4/713-v5.2-net-phylink-avoid-reducing-support-mask.patch
 * backport-5.4/714-v5.3-net-sfp-Stop-SFP-polling-and-interrupt-handling-duri.patch
 * backport-5.4/715-v5.3-net-phylink-don-t-start-and-stop-SGMII-PHYs-in-SFP-m.patch
 * backport-5.4/740-v5.5-net-phy-avoid-matching-all-ones-clause-45-PHY-IDs.patch
 * backport-5.4/741-v5.5-net-phylink-fix-link-mode-modification-in-PHY-mode.patch
 * pending-5.4/103-MIPS-perf-ath79-Fix-perfcount-IRQ-assignment.patch
 * pending-5.4/131-spi-use-gpio_set_value_cansleep-for-setting-chipsele.patch
 * pending-5.4/132-spi-spi-gpio-fix-crash-when-num-chipselects-is-0.patch
 * pending-5.4/220-optimize_inlining.patch
 * pending-5.4/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch
 * pending-5.4/475-mtd-spi-nor-Add-Winbond-w25q128jv-support.patch
 * pending-5.4/477-mtd-add-spi-nor-add-mx25u3235f.patch
 * pending-5.4/479-mtd-spi-nor-add-eon-en25qh64.patch

Some bigger changes were done to this feature and we did not port this patch yet:
 * hack-5.4/207-disable-modorder.patch

This depends on BOOTMEM which was removed from the kernel, this needs some bigger changes:
 * hack-5.4/930-crashlog.patch

A different version of the FPU disable patch was merged upstream, OpenWrt needs some adaptations.
 * pending-5.4/304-mips_disable_fpu.patch

- no crashlog support yet as a required file got deleted upstream
- Removed patch below, which is now seen as a recursive dependency [1]
- Removed patch below due to build error [2]
- fix still required to avoid identical function def [3]
- Fixes included from Blocktrron
- Fixes included from Chunkeey
- Fix included from nbd regarding "dst leak in Flow Offload"

[1] target/linux/generic/hack-5.4/260-crypto_test_dependencies.patch
[2] target/linux/generic/hack-5.4/207-disable-modorder.patch
[3] target/linux/generic/pending-5.4/613-netfilter_optional_tcp_window_check.patch

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4 months agokernel: copy kernel 4.19 code to 5.4
Hauke Mehrtens [Sun, 23 Feb 2020 12:20:11 +0000 (13:20 +0100)]
kernel: copy kernel 4.19 code to 5.4

No changes were done to the patches while coping them. Currently they do
not apply on top of kernel 5.4.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4 months agolibubox: update to latest Git HEAD
Jo-Philipp Wich [Thu, 27 Feb 2020 21:03:18 +0000 (22:03 +0100)]
libubox: update to latest Git HEAD

7da6643 tests: blobmsg: add test case
75e300a blobmsg: fix wrong payload len passed from blobmsg_check_array

Fixes: FS#2833
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
4 months agoath79: also reduce spi-max-frequency for buffalo_wzr-hp-ag300h
Adrian Schmutzler [Thu, 27 Feb 2020 13:49:08 +0000 (14:49 +0100)]
ath79: also reduce spi-max-frequency for buffalo_wzr-hp-ag300h

In accordance to ebc090e420d1 ("ath79: reduce spi-max-frequency to 50 MHz")
this also reduces the spi-max-frequency to 50 MHz for the last remaining
device with higher frequency in ath79. This will save us from having a
single special case that will require adjustment when the spi driver for
this device is changed in the future.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Chuanhong Guo <gch981213@gmail.com>
4 months agokirkwood: apply minor DTS style improvements
Adrian Schmutzler [Thu, 27 Feb 2020 12:05:51 +0000 (13:05 +0100)]
kirkwood: apply minor DTS style improvements

This applies some minor DTS style improvements to the files kept
in OpenWrt at the moment:

- harmonize/improve LED/pinmux node names
- harmonize empty lines between nodes
- change "ok" to "okay"
- some other minor formatting adjustments

Since changes are only cosmetical, they are only applied to the
"newer" DTS files for kernel 4.19.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agokirkwood: convert DTS patches into plain DTS files
Sungbo Eo [Mon, 24 Feb 2020 12:06:04 +0000 (21:06 +0900)]
kirkwood: convert DTS patches into plain DTS files

Move DTS files newly created by patch files to files directory. This will make
these files much more maintainable.

Patching the kernel Makefile is unnecessary, as the DTS files specified in
DEVICE_DTS will be compiled by OpenWrt buildroot anyway.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agoath79: reduce spi-max-frequency to 50 MHz
Adrian Schmutzler [Thu, 27 Feb 2020 10:55:36 +0000 (11:55 +0100)]
ath79: reduce spi-max-frequency to 50 MHz

The introduction of ebf0d8dadeca ("ath79: add new ar934x spi driver")
made the SPI memory unusable on devices with very high spi-max-frequency
(104 MHz).

Here's how the actual clock is calculated: (AHB_CLK/((CLOCK_DIVIDER+1)*2))
where AHB_CLK is a fixed clock (e.g. 200MHz on AR9331) and CLOCK_DIVIDER
is the parameter we can set. Highest clock according to this formula is
AHB_CLK/2 (100MHz, but that didn't work in device tests).
The next possible value is AHB_CLK/4 (50MHz). Speeds between 50 MHz and
100 MHz will be rounded down, so using values higher than 50 MHz does
not provide any benefit.

Consequently, this patch reduces spi-max-frequency for all devices with
values higher than 50 MHz to 50 MHz (effectively, this only affects
devices with 104 MHz before this patch).

Tested on GL.inet GL-AR150:
Boot fails with 104 MHz but is successful with both 50 MHz and 80 MHz
(fast-read), where the latter two yield identical read speeds.

Fixes: ebf0d8dadeca ("ath79: add new ar934x spi driver")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agoath79: fix spi-max-frequency for wAP G-5HacT2HnD
Roger Pueyo Centelles [Mon, 24 Feb 2020 20:07:59 +0000 (21:07 +0100)]
ath79: fix spi-max-frequency for wAP G-5HacT2HnD

The introduction of ebf0d8dade (ath79: add new ar934x spi driver)
made the SPI memory unusable. Reducing the spi-max-frequency to
a smaller value makes it work again.

Tested on two MikroTik RouterBOARD wAP G-5HacT2HnD devices.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
4 months agobase-files: add all buildinfo with INCLUDE_CONFIG
Xu Wang [Sat, 8 Feb 2020 23:04:11 +0000 (23:04 +0000)]
base-files: add all buildinfo with INCLUDE_CONFIG

CONFIG_INCLUDE_CONFIG option is helpful for being able to rebuild the
exact same firmware as you see on a live OpenWRT instance, but it's
crucially missing feeds information, so we can't rebuild the exact same
package versions. This commit fixes this by adding the remaining feeds
(and version) buildinfo files to the image.

Signed-off-by: Xu Wang <xwang1498@gmx.com>
4 months agoppp: backport security fixes
Petr Štetiar [Thu, 20 Feb 2020 08:03:54 +0000 (09:03 +0100)]
ppp: backport security fixes

8d45443bb5c9 pppd: Ignore received EAP messages when not doing EAP
8d7970b8f3db pppd: Fix bounds check in EAP code
858976b1fc31 radius: Prevent buffer overflow in rc_mksid()

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes: CVE-2020-8597
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
4 months agoRevert "ppp: backport security fixes"
Jo-Philipp Wich [Wed, 26 Feb 2020 15:36:16 +0000 (16:36 +0100)]
Revert "ppp: backport security fixes"

This reverts commit 215598fd03899c19a9cd26266221269dd5ec8cee since it
didn't contain a reference to the CVE it addresses. The next commit
will re-add the commit including a CVE reference in its commit message.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
4 months agoath79: add support for MikroTik RouterBOARD 922UAGS-5HPacD
Roger Pueyo Centelles [Sun, 26 Jan 2020 16:56:05 +0000 (17:56 +0100)]
ath79: add support for MikroTik RouterBOARD 922UAGS-5HPacD

This patch ports support for the MikroTik RouterBOARD 922UAGS-5HPacD
with a built-in 802.11ac High-Power radio (31dBm), which was already
available in the ar71xx target.

See https://mikrotik.com/product/RB922UAGS-5HPacD for more info.

Specifications:
- SoC: Qualcomm Atheros QCA9558 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9882 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE-in 24V
- SFP: 1x host
- USB: 1x 2.0 type A
- PCIe: 1x Mini slot (also contains USB 2.0 for 3G/LTE modems)
- SIM slot: 1x mini-SIM

Working:
- Board/system detection
- SPI and NAND storage
- PCIe
- USB type A host
- Wireless
- Ethernet
- LEDs (user, phy0)
- Reset button
- Sysupgrade to/from ar71xx

Not supported:
- RSSI LEDs
- SFP cage

Installation methods:
- Sysupgrade from ar71xx (it is advisable to use the -n option to
wipe any previous settings), or
- Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
4 months agorbextract: support devices with plain RLE caldata
Roger Pueyo Centelles [Wed, 29 Jan 2020 10:27:03 +0000 (11:27 +0100)]
rbextract: support devices with plain RLE caldata

Old MikroTik devices have the RLE-encoded radio calibration data
directly stored in the art (hard_config) partition, without LZO
compression nor any preceding ERD magic bytes. This commit adds
a fallback for these devices.

Tested on the ath79 target with a MikroTik SXT 5nD r2 (SXT Lite5),
only locally --not yet merged upstream--.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
4 months agokernel: x86_64: drop CALGARY properly
Kevin Darbyshire-Bryant [Tue, 25 Feb 2020 16:38:35 +0000 (16:38 +0000)]
kernel: x86_64: drop CALGARY properly

Use correct config syntax of 'is not set' instead of just commenting the
line

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
4 months agomediatek: add latest fixes provided by MTK
John Crispin [Tue, 25 Feb 2020 16:15:07 +0000 (17:15 +0100)]
mediatek: add latest fixes provided by MTK

Signed-off-by: John Crispin <john@phrozen.org>
4 months agokernel: x86_64: drop CALGARY IOMMU
Kevin Darbyshire-Bryant [Mon, 24 Feb 2020 13:53:57 +0000 (13:53 +0000)]
kernel: x86_64: drop CALGARY IOMMU

The calgary IOMMU was only used on high-end IBM systems in the early
x86_64 age.  This is an unlikely OpenWrt target and in fact upstream
are looking to drop the driver entirely with the bonus that we no
longer see:

[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
4 months agomac80211: enhance wifi reload
John Crispin [Tue, 25 Feb 2020 16:03:44 +0000 (17:03 +0100)]
mac80211: enhance wifi reload

If the reconf call fails force a full restart of the radio.

Signed-off-by: John Crispin <john@phrozen.org>
4 months agohostapd: enhance wifi reload
John Crispin [Tue, 25 Feb 2020 16:01:55 +0000 (17:01 +0100)]
hostapd: enhance wifi reload

Add a radio_config_id property. If the radio config changes return an error
upon receiving the reconf call.

Signed-off-by: John Crispin <john@phrozen.org>
4 months agomt76: update to the latest version
Felix Fietkau [Tue, 25 Feb 2020 12:33:46 +0000 (13:33 +0100)]
mt76: update to the latest version

0a53dcda5203 mt76: mt7603: add upper limit for dynamic sensitivity minimum receive power
46e63c05f7d1 mt76: mt7603: enable dynamic sensitivity adjustment by default
81476f11b68c mt76: mt7615: fix antenna mask initialization in DBDC mode

Signed-off-by: Felix Fietkau <nbd@nbd.name>
4 months agobase-files: diag: restore default trigger for 'boot' LED
Piotr Dymacz [Fri, 31 Jan 2020 14:22:54 +0000 (15:22 +0100)]
base-files: diag: restore default trigger for 'boot' LED

For devices without a dedicated 'diag' LED, we use sometimes one of
other LEDs for indicating at least 'boot', 'failsafe' and 'upgrade'
stages. In some cases, at the same time these LEDs have defined default
triggers in DTS using 'linux,default-trigger' property. Current 'diag'
setup removes the trigger and turns off 'boot' LED after bootup.

One of the examples of such device is TP-Link TL-WR841N v14 (ramips)
which uses 'wlan' LED with defined 'linux,default-trigger' for 'diag':

aliases {
        led-boot = &led_wlan;
        led-failsafe = &led_wlan;
        led-upgrade = &led_wlan;
};

[...]

led_wlan: wlan {
        label = "tl-wr841n-v14:green:wlan";
        gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
        linux,default-trigger = "phy0tpt";
};

This patch extends 'diag.sh' and 'leds.sh' scripts to make sure default
trigger defined in DTS is restored for 'diag' LED which isn't used for
indicating 'running' stage.

Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
4 months agohostapd: start hostapd/wpa_supplicant for all wiphy devices
Piotr Dymacz [Mon, 20 Jan 2020 18:35:01 +0000 (19:35 +0100)]
hostapd: start hostapd/wpa_supplicant for all wiphy devices

c888e17e06 ("hostapd: manage instances via procd instead of pidfile")
added procd support for managing hostapd and wpa_supplicant daemons
but at the same time limited wiphy names to 'phy*'.

This brings back initial behaviour (introduced in 60fb4c92b6 ("hostapd:
add ubus reload") and makes procd manage daemons for any wiphy device
found in '/sys/class/ieee80211'.

CC: Felix Fietkau <nbd@nbd.name>
CC: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
4 months agoumbim: move package to 'WWAN' submenu
Piotr Dymacz [Mon, 25 Nov 2019 20:00:30 +0000 (21:00 +0100)]
umbim: move package to 'WWAN' submenu

'uqmi' was moved to 'WWAN' submenu in 9abdeee0b7.
Let's be consistent and do the same with 'umbim'.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
4 months agombedtls: use correct SPDX License Identifier and add License file
Josef Schlehofer [Sat, 22 Feb 2020 22:03:37 +0000 (23:03 +0100)]
mbedtls: use correct SPDX License Identifier and add License file

License "GPL-2.0+" is deprecated License Identifier according to
SPDX License list [1]. The correct one is GPL-2.0-or-later.
While at it, also add the License file.

[1] https://spdx.org/licenses/

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
4 months agombedtls: update to version 2.16.5
Josef Schlehofer [Sat, 22 Feb 2020 22:03:36 +0000 (23:03 +0100)]
mbedtls: update to version 2.16.5

Changelog:
https://tls.mbed.org/tech-updates/releases/mbedtls-2.16.5-and-2.7.14-released

Security advisory:
https://tls.mbed.org/tech-updates/security-advisories/mbedtls-security-advisory-2020-02

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
4 months agostrace: update to version 5.5
Josef Schlehofer [Sun, 23 Feb 2020 07:48:39 +0000 (08:48 +0100)]
strace: update to version 5.5

Changelog:
https://strace.io/files/5.5/

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
4 months agokernel: Sort generic configuration
Hauke Mehrtens [Sun, 23 Feb 2020 12:20:11 +0000 (13:20 +0100)]
kernel: Sort generic configuration

This was done by executing these commands:

$ ./scripts/kconfig.pl '+' target/linux/generic/config-4.19 /dev/null > target/linux/generic/config-4.19-new
$ mv target/linux/generic/config-4.14-new target/linux/generic/config-4.14

$ ./scripts/kconfig.pl '+' target/linux/generic/config-4.14 /dev/null > target/linux/generic/config-4.14-new
$ mv target/linux/generic/config-4.19-new target/linux/generic/config-4.19

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4 months agolinux-atm: Fix compile warning
Hauke Mehrtens [Sat, 22 Feb 2020 19:39:47 +0000 (20:39 +0100)]
linux-atm: Fix compile warning

The function trace_on_exit() is given to atexit() as a parameter, but
atexit() only takes a function pointer to a function with a void
parameter.

This problem was introduced when the on_exit() function was incompletely
replaced by atexit().

Fixes: ba6c8bd6142f ("linux-atm: add portability fixes")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4 months agoath10k-ct: Use ath10k-ct version 5.4
Hauke Mehrtens [Sat, 9 Nov 2019 16:06:06 +0000 (17:06 +0100)]
ath10k-ct: Use ath10k-ct version 5.4

This makes ath10k-ct use the version based on kernel 5.4 by default.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4 months agoath10k-ct: Update to version 2020-02-18
Hauke Mehrtens [Sat, 22 Feb 2020 18:12:34 +0000 (19:12 +0100)]
ath10k-ct: Update to version 2020-02-18

This adds AP VLAN support.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4 months agomac80211: Allow IBSS mode and different beacon intervals
Hauke Mehrtens [Sat, 9 Nov 2019 16:06:05 +0000 (17:06 +0100)]
mac80211: Allow IBSS mode and different beacon intervals

ath10k-ct supports the combination to select IBSS (ADHOC) mode and
different beacon intervals together. mac80211 does not like this
combination, but Ben says this is ok, so remove this check.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4 months agortl8812au-ct: Update to version 2020-01-12
Hauke Mehrtens [Wed, 5 Feb 2020 21:49:27 +0000 (22:49 +0100)]
rtl8812au-ct: Update to version 2020-01-12

This fixes compile problems with kernel 5.4

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
4 months agoath79: add missing reset-gpios for NanoStation Loco M (XW)
Roger Pueyo Centelles [Mon, 24 Feb 2020 17:21:49 +0000 (18:21 +0100)]
ath79: add missing reset-gpios for NanoStation Loco M (XW)

When porting support from ar71xx to ath79, the reset-gpios option was
missed. Due to a hardware bug, this would eventually leave the devices
with RX-deaf Ethernet PHY.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
4 months agokernel: bump 4.19 to 4.19.106
Koen Vandeputte [Mon, 24 Feb 2020 15:11:02 +0000 (16:11 +0100)]
kernel: bump 4.19 to 4.19.106

Refreshed all patches.

Remove upstreamed:
- 950-0786-leds-pca963x-Fix-open-drain-initialization.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
4 months agokirkwood: remove kmod-i2c-mv64xxx from DEVICE_PACKAGES
Sungbo Eo [Sun, 23 Feb 2020 15:14:22 +0000 (00:14 +0900)]
kirkwood: remove kmod-i2c-mv64xxx from DEVICE_PACKAGES

Commit 9a1f441ac81c ("kirkwood: enable SoC drivers in the kernel config")
enabled I2C_MV64XXX in the kernel config, and the subsequent commit 0d5ba94088ef
("orion: enable SoC drivers in the kernel config") removed kmod-i2c-mv64xxx
package entirely. As the feature is now kernel built-in and the package does not
exist anymore, we can safely remove kmod-i2c-mv64xxx from DEVICE_PACKAGES.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
4 months agokernel: bump 4.19 to 4.19.105
Koen Vandeputte [Fri, 21 Feb 2020 14:09:00 +0000 (15:09 +0100)]
kernel: bump 4.19 to 4.19.105

Refreshed all patches.

Fixes:
- CVE-2013-1798
- CVE-2019-3016

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
4 months agokernel: bump 4.14 to 4.14.171
Koen Vandeputte [Fri, 21 Feb 2020 14:04:52 +0000 (15:04 +0100)]
kernel: bump 4.14 to 4.14.171

Refreshed all patches.

Fixes:
- CVE-2013-1798

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
4 months agokirkwood: tidy up hwmon_fancontrol
Sungbo Eo [Sun, 23 Feb 2020 15:17:16 +0000 (00:17 +0900)]
kirkwood: tidy up hwmon_fancontrol

Add indent and sort board_name alphabetically.

Sourcing /lib/functions.sh is already handled by /etc/rc.common. Drop the line.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
4 months agourngd: avoid PKG_NAME in define lines
Sungbo Eo [Sun, 23 Feb 2020 12:38:24 +0000 (21:38 +0900)]
urngd: avoid PKG_NAME in define lines

> Avoid reuse of PKG_NAME in call, define and eval lines for consistency and
> readability. Write the full name instead.

Ref: https://openwrt.org/docs/guide-developer/packages

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
4 months agourandom-seed: avoid PKG_NAME in define lines
Sungbo Eo [Sun, 23 Feb 2020 12:37:36 +0000 (21:37 +0900)]
urandom-seed: avoid PKG_NAME in define lines

> Avoid reuse of PKG_NAME in call, define and eval lines for consistency and
> readability. Write the full name instead.

Ref: https://openwrt.org/docs/guide-developer/packages

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
4 months agokirkwood: add kmod-hwmon-core to DEVICE_PACKAGES
Sungbo Eo [Sun, 23 Feb 2020 15:14:22 +0000 (00:14 +0900)]
kirkwood: add kmod-hwmon-core to DEVICE_PACKAGES

kmod-hwmon-lm* will not get into images unless kmod-hwmon-core is added to
DEVICE_PACKAGES as well.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[only address kmod-hwmon-core in this commit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agokirkwood: tidy up image Makefile
Sungbo Eo [Sun, 23 Feb 2020 15:16:16 +0000 (00:16 +0900)]
kirkwood: tidy up image Makefile

- use k in SIZE variables
- break long lines

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
4 months agokirkwood: fix device node name of Iomega ix2-200
Sungbo Eo [Sun, 23 Feb 2020 15:12:23 +0000 (00:12 +0900)]
kirkwood: fix device node name of Iomega ix2-200

The current device node name of ix2-200 is "iom_ix2_200", which results
in a SUPPORTED_DEVICES string "iom,ix2,200" that does not match the
compatible in DTS and the board name used in board.d.

Fix this by replacing the second underscore with a dash, following
vendor_model scheme.

Fixes: 27b2f0fc0fc5 ("kirkwood: add support for Iomega Storcenter ix2-200")

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[commit title/message rephrase]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agoath79: fix TP-Link TL-WA901ND v2 PHY stuck in reset
David Bauer [Sun, 23 Feb 2020 11:50:30 +0000 (12:50 +0100)]
ath79: fix TP-Link TL-WA901ND v2 PHY stuck in reset

Some newer bootloaders for the TP-Link TL-WA901ND put the ethernet PHY
in reset before loading the kernel, thus the LAN interface is not
working in OpenWrt.

Clear the reset to restore ethernet functionality.

Signed-off-by: David Bauer <mail@david-bauer.net>
4 months agox86: avoid underscore in package name
Sungbo Eo [Sun, 23 Feb 2020 04:05:35 +0000 (13:05 +0900)]
x86: avoid underscore in package name

As 07e1d88d7beb ("kernel: avoid underscore in *6lowpan package names") shows,
underscores might cause build failures. Replace underscore with dash.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
4 months agoltq-vdsl-mei: avoid underscore in package name
Sungbo Eo [Sun, 23 Feb 2020 04:05:27 +0000 (13:05 +0900)]
ltq-vdsl-mei: avoid underscore in package name

As 07e1d88d7beb ("kernel: avoid underscore in *6lowpan package names") shows,
underscores might cause build failures. Replace underscore with dash.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
4 months agoramips: move includes to DTSI for mt7628an_tplink_8m*
Adrian Schmutzler [Sat, 22 Feb 2020 18:33:41 +0000 (19:33 +0100)]
ramips: move includes to DTSI for mt7628an_tplink_8m*

All devices inherited from mt7628an_tplink_8m.dtsi and
mt7628an_tplink_8m-split-uboot.dtsi contain the same additional
includes in the DTS files.

Move them to the DTSI files instead.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agoramips: move compatible for Ubiquiti Edgerouter X to DTS file
Adrian Schmutzler [Sat, 22 Feb 2020 18:28:17 +0000 (19:28 +0100)]
ramips: move compatible for Ubiquiti Edgerouter X to DTS file

So far, the compatible for the Ubiquiti Edgerouter X has been
defined in the DTSI file and inherited for the edgerouterx.dts,
but overwritten for the edgerouterx-sfp.dts. In contrast, the
model was stored in the DTS file in both cases.

To resolve this somewhat confusing situation, move the compatible
with the device name for edgerouterx to the DTS file as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agoramips: remove redundant includes in DTS files
Adrian Schmutzler [Sat, 22 Feb 2020 18:26:17 +0000 (19:26 +0100)]
ramips: remove redundant includes in DTS files

Many DTS files contain the same includes again that are already
present in the DTSI files they are derived from.

Remove those redundant includes in the DTS files. For vocore, the
include is moved to the parent DTSI file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agoath79: remove redundant includes in DTS files
Adrian Schmutzler [Sat, 22 Feb 2020 18:16:05 +0000 (19:16 +0100)]
ath79: remove redundant includes in DTS files

Many DTS files contain the same includes again that are already
present in the DTSI files they are derived from.

Remove those redundant includes in the DTS files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agopackages/boot: bump arm-trusted-firmware-mvebu version
Scott Roberts [Wed, 22 Jan 2020 22:42:46 +0000 (15:42 -0700)]
packages/boot: bump arm-trusted-firmware-mvebu version

The current version of ATF does not support power off for SGMII
COMPHY.  Update to latest ATF to resolve this issue.

Signed-off-by: Scott Roberts <ttocsr@gmail.com>
4 months agomac80211: backport fix TID field in monitor mode transmit
Fredrik Olofsson [Wed, 29 Jan 2020 14:39:53 +0000 (15:39 +0100)]
mac80211: backport fix TID field in monitor mode transmit

Backport 753ffad3d6243303994227854d951ff5c70fa9e0 as merged in Linux v5.5-rc3.

Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
4 months agokernel: fix xt_connmark.h
Martin Schiller [Wed, 5 Feb 2020 07:12:54 +0000 (08:12 +0100)]
kernel: fix xt_connmark.h

Commit a1cfe0dcbb24 (kernel: connmark set-dscpmark follow upstreamimg
attempt") broke the usage of xt_connmark.h in user-space (e.g.
strongswan), because the BIT() macro is unknown there.

Fixes: a1cfe0dcbb24 (kernel: connmark set-dscpmark follow upstreamimg attempt")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
4 months agotoolchain/binutils: Add binutils 2.34
Daniel Engberg [Mon, 3 Feb 2020 15:30:06 +0000 (15:30 +0000)]
toolchain/binutils: Add binutils 2.34

Refresh patches
Drop 300-012_check_ldrunpath_length.patch

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
4 months agopackage/utils/f2fs-tools: Update to 1.13.0
Daniel Engberg [Tue, 4 Feb 2020 01:10:17 +0000 (01:10 +0000)]
package/utils/f2fs-tools: Update to 1.13.0

Update f2fs-tools to 1.13.0
Remove upstreamed patches
Disable build of static library

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
4 months agogeneric: refresh patches
Aleksander Jan Bajkowski [Sun, 9 Feb 2020 15:23:06 +0000 (16:23 +0100)]
generic: refresh patches

just run: make target/linux/refresh V=s

Fixes: 6e315de0f422acf66c3505a4ed8c095a0f5d3424

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
4 months agousbmode: Update modeswitch data to 20191128
Davide Fioravanti [Wed, 19 Feb 2020 18:43:00 +0000 (19:43 +0100)]
usbmode: Update modeswitch data to 20191128

Add support for new hardware

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
4 months agokernel: remove non-existant symbols from 4.19 config
Aleksander Jan Bajkowski [Tue, 18 Feb 2020 19:32:11 +0000 (20:32 +0100)]
kernel: remove non-existant symbols from 4.19 config

These symbols only exist in kernel version <= 4.15

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
4 months agokernel: replace SUBDIRS with M in package recipes
Tomasz Maciej Nowak [Mon, 20 Jan 2020 14:42:00 +0000 (15:42 +0100)]
kernel: replace SUBDIRS with M in package recipes

The SUBDIRS variable has been removed in kernel 5.4, and was deprecated
since the beginnig of kernel git history in favour of M or KBUILD_EXTMOD.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
4 months agolinux-firmware: update to 20200122
DENG Qingfang [Fri, 14 Feb 2020 13:41:06 +0000 (21:41 +0800)]
linux-firmware: update to 20200122

Update linux-firmware to 20200122

git log --pretty=oneline --abbrev-commit 20191215..20200122

1eb2408 linux-firmware: Update firmware file for Intel Bluetooth AX200
0dc1611 linux-firmware: Update firmware file for Intel Bluetooth AX201
d03f79c linux-firmware: Update firmware file for Intel Bluetooth 9560
aab62bc linux-firmware: Update firmware file for Intel Bluetooth 9260
ed0aa3a nvidia: add TU102/TU104/TU106 signed firmware
9c340bd amdgpu: update navi10 firmware for 19.50
3b4a503 amdgpu: Add navi10 TA ucode
16cc13a Merge branch 'v1.1.3' of https://github.com/ruiwang-mtk/linux_fw_vpu_v1.1.37f3177d mediatek: update MT8173 VPU firmware to v1.1.3
67d4ff5 Mellanox: Add new mlxsw_spectrum firmware xx.2000.2714
f1c9e7b radeon: update oland rlc microcode from amdgpu
b1dafb7 amdgpu: update vega20 microcode for 19.50
c38789e amdgpu: update vega12 microcode for 19.50
5a141c1 amdgpu: update vega10 microcode for 19.50
a03173a amdgpu: update picasso microcode for 19.50
86e9a5f amdgpu: update raven2 microcode for 19.50
febe09a amdgpu: update raven microcode for 19.50
af76fd0 amdgpu: update navi10 microcode for 19.50
b5b176a amdgpu: update navi14 microcode for 19.50
ad90178 amdgpu: add TA microcode for Raven asics
379551b qed: Add firmware 8.42.2.0
58b4003 Merge branch 'RB3-wlan-firmware-1387-v2' of https://github.com/andersson/linux-firmware
5967a45 Adjust WHENCE entry to check_whence doesn't complain
d1e743d Merge branch 'master' of https://github.com/NXP/mwifiex-firmware
d6219ab qcom: Switch SDM845 WLAN firmware
e65245c linux-firmware: add NXP firmware licence file
6871bff Merge branch 'ath10k-20191220' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/linux-firmware
b142c2e ath10k: WCN3990 hw1.0: add firmware WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
8809b87 ath10k: QCA9984 hw1.0: update firmware-5.bin to 10.4-3.9.0.2-00070
513d70c ath10k: QCA988X hw2.0: update firmware-5.bin to 10.2.4-1.0-00047
203435b ath10k: QCA9888 hw2.0: update firmware-5.bin to 10.4-3.9.0.2-00070
a66d2fc ath10k: QCA9887 hw1.0: update firmware-5.bin to 10.2.4-1.0-00047
6d19154 ath10k: QCA6174 hw3.0: update board-2.bin
c4586ff linux-firmware: Update AMD cpu microcode

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
4 months agoiw: update to 5.4
DENG Qingfang [Wed, 12 Feb 2020 12:16:05 +0000 (20:16 +0800)]
iw: update to 5.4

Update iw to 5.4
This increases the ipk size of iw-tiny/full by about 400 bytes

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
4 months agolibbsd: update to 0.10.0
Rosen Penev [Thu, 20 Feb 2020 03:42:35 +0000 (19:42 -0800)]
libbsd: update to 0.10.0

Removed all upstream patches.

Added PKG_BUILD_PARALLEL for faster compilation.

Small Makefile rearrangements for consistency between packages.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
4 months agobuild: Add additional kernel debug options
Hauke Mehrtens [Wed, 12 Feb 2020 10:49:02 +0000 (11:49 +0100)]
build: Add additional kernel debug options

Make it possible to activate some additional kernel debug options.
This can be used to debug some problems in kernel drivers.

Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
4 months agobuild: Add KCOV kernel code coverage for fuzzing
Hauke Mehrtens [Wed, 12 Feb 2020 10:49:01 +0000 (11:49 +0100)]
build: Add KCOV kernel code coverage for fuzzing

The adds an option to activate KCOV (Code coverage for fuzzing).

Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
4 months agobuild: Add option KERNEL_KASAN
Hauke Mehrtens [Wed, 12 Feb 2020 10:49:00 +0000 (11:49 +0100)]
build: Add option KERNEL_KASAN

The kernel kernel address sanitizer is able to detect some memory
bugs in the kernel like out of range array accesses.

Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
4 months agobuild: Add option KERNEL_UBSAN
Hauke Mehrtens [Wed, 12 Feb 2020 10:48:59 +0000 (11:48 +0100)]
build: Add option KERNEL_UBSAN

The kernel Undefined Behavior Sanitizer is able to detect some memory
bugs in the kernel like out of range array accesses.

Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
4 months agox86: Add missing kernel option CONFIG_X86_DECODER_SELFTEST
Hauke Mehrtens [Tue, 11 Feb 2020 18:01:24 +0000 (19:01 +0100)]
x86: Add missing kernel option CONFIG_X86_DECODER_SELFTEST

This option has now a different dependency and can be activated, set a
default value.

Fixes: 20b5a4ca01ca ("kernel: bump 4.19 to 4.19.101")
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Tested-by: Alexandru Ardelean <ardeleanalex@gmail.com>
4 months agorssileds: add dependencies based on LDFLAGS
Adrian Schmutzler [Thu, 20 Feb 2020 17:38:04 +0000 (18:38 +0100)]
rssileds: add dependencies based on LDFLAGS

This adds the direct dependencies introduced by TARGET_LDFLAGS
to the package's DEPENDS variable.

This was found by accidentally building rssileds on octeon, which
resulted in:

"Package rssileds is missing dependencies for the following libraries:
libnl-tiny.so"

Though the dependencies are provided when building for the
relevant targets ar71xx, ath79 and ramips, it seems more tidy to
specify them explicitly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agokirkwood: do not expose status LED to user config by default
Adrian Schmutzler [Fri, 21 Feb 2020 20:09:25 +0000 (21:09 +0100)]
kirkwood: do not expose status LED to user config by default

So far, the state of status LEDs is set up in 01_leds for many devices
in kirkwood target. As those LEDs are also controlled by diag.sh,
exposing them to the user via uci config by default seems not helpful
and might even have confusing results for the user.

Thus, remove the ucidef_set_led_default setup for power/status LED, but
do not touch the rest where user control is actually a feature.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agokirkwood: set default state for status LEDs in device tree
Adrian Schmutzler [Wed, 19 Feb 2020 16:03:04 +0000 (17:03 +0100)]
kirkwood: set default state for status LEDs in device tree

This adds the default-state = "on"; statement for the power or
primary status LED in DTS on kirkwood. This will ensure that this
LED will be lit up very early in the boot process (i.e. before
diag.sh is executed) and thus will provide an additional hint to the
user when problems arise during early boot process.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agokirkwood: add diag LEDs for ZyXEL NSA325
Adrian Schmutzler [Wed, 19 Feb 2020 15:39:32 +0000 (16:39 +0100)]
kirkwood: add diag LEDs for ZyXEL NSA325

This device has had no diag LEDs set up so far, so let's just
add them.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agokirkwood: use generic diag.sh
Pawel Dembicki [Tue, 4 Feb 2020 16:26:47 +0000 (17:26 +0100)]
kirkwood: use generic diag.sh

This commit removes the target-specific diag.sh script. This way, the
generic one is used for the target, which uses DT-aliases to specify the
LEDs used.

Generic diag.sh allow to use different LEDs to indicate different states.
Non-red status LEDs for indicating boot and a running system.
Where possible, the red or orange LEDs are used to indicate failsafe
mode and a running upgrade.

Compile-tested: all target devices.
Run-tested: CheckPoint L-50

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[remove unrelated cosmetic changes, rename some labels, add pogo_e02]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agolldpd: bump to 1.0.5
Stijn Tintel [Thu, 20 Feb 2020 21:39:06 +0000 (23:39 +0200)]
lldpd: bump to 1.0.5

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
4 months agoath79: add support for Teltonika RUT955
Daniel Golle [Sun, 2 Feb 2020 16:09:50 +0000 (18:09 +0200)]
ath79: add support for Teltonika RUT955

Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 4G/3G module (example: Quectel EC-25EU)
- internal microSD slot (spi-mmc, buggy and disabled for now)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-24V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 11x LED (4 are driven by AR9344, 7 by 74HC595)
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector

Serial console (/dev/ttyS0) pinout:

- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side

Flash instruction:

Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.2".

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
4 months agoserial: ar933x_uart: add rs485 support
Daniel Golle [Wed, 5 Feb 2020 15:00:57 +0000 (17:00 +0200)]
serial: ar933x_uart: add rs485 support

Add support for RS485 tranceiver with transmit/receive switch hooked
to a RTS GPIO pin.
Use the 'rts-gpios' and 'rs485-rts-active-low' properties as described
in devicetree/bindings/serial/rs485.yaml.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
4 months agoath79: add support for TP-Link TL-WA701ND/730RE/801ND/901ND v1
Adrian Schmutzler [Fri, 14 Feb 2020 14:38:55 +0000 (15:38 +0100)]
ath79: add support for TP-Link TL-WA701ND/730RE/801ND/901ND v1

This adds support for the various clones of the TL-WA830RE recently
supported in fb99ac6807f2 ("ath79: add support for TP-Link TL-WA830RE v1"):

- tplink,tl-wa701nd-v1
- tplink,tl-wa730re-v1
- tplink,tl-wa801nd-v1
- tplink,tl-wa830re-v1 (already supported)
- tplink,tl-wa901nd-v1

Since these devices are 100%-clones in ar71xx, this patch adds all
of them without run-testing (as this has been done for TL-WA830RE v1).

Specifications:
- SOC: Atheros AR7240
- CPU: 400MHz
- Flash: 4 MiB (Spansion S25FL032P)
- RAM: 32 MiB (Zentel A3S56D40FTP-G5)
- WLAN: Atheros AR9280 bgn 2x2
- Ethernet: 1 port (100M)

Flash instructions:
- install from u-boot with tftp (requires serial access)
  > setenv ipaddr a.b.c.d
  > setenv serverip e.f.g.h
  > tftpboot 0x80000000 \
      openwrt-ath79-tiny-tplink_tl-waxxxxx-v1-squashfs-factory.bin
  > erase 0x9f020000 +0x3c0000
  > cp.b 0x80000000 0x9f020000 0x3c0000
  > bootm 0x9f020000
- flash factory image from OEM WebUI
- sysupgrade from ar71xx image

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agoramips: fix HiWiFi HC5761A USB port
DENG Qingfang [Wed, 12 Feb 2020 13:14:26 +0000 (21:14 +0800)]
ramips: fix HiWiFi HC5761A USB port

Export GPIO 41 to power USB port

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
4 months agoramips: gsw_mt7621: disable PORT 5 MAC RX/TX flow control by default
Petr Štetiar [Tue, 11 Feb 2020 10:17:41 +0000 (11:17 +0100)]
ramips: gsw_mt7621: disable PORT 5 MAC RX/TX flow control by default

Looking at the current upstream driver implementation, it seems like the
TX/RX flow control is enabled only if the flow control pause option is
resolved from the device/link partner advertisements (or otherwise set).

On the other hand, our current in-tree driver force enables TX/RX
flow control by default, thus possibly leading to TX timeouts if the
other end sends pause frames (which are not properly handled?):

 WARNING: CPU: 3 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x1ac/0x324
 NETDEV WATCHDOG: eth0 (mtk_soc_eth): transmit queue 0 timed out

Disabling the flow control on PORT 5 MAC seems to fix this issues as the
pause frames are then filtered out. While at it, I'm removing the if
condition completely as suggested, since this code is run only on mt7621
SoC, so there is no need to check for the silicon revisions.

Ref: https://lists.openwrt.org/pipermail/openwrt-devel/2017-November/009882.html
Ref: https://forum.openwrt.org/t/mtk-soc-eth-watchdog-timeout-after-r11573/50000/12
Suggested-by: Felix Fietkau <nbd@nbd.name>
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
4 months agomt76: update to the latest version
Felix Fietkau [Thu, 20 Feb 2020 14:06:14 +0000 (15:06 +0100)]
mt76: update to the latest version

f4415afce213 mt76: mt76u: loop over all possible rx queues in mt76u_rx_tasklet
5b9f949cb760 mt76: mt76u: fix a possible memory leak in mt76u_init
fd892bc033fb mt76: mt76u: rely only on data buffer for usb control messagges

Signed-off-by: Felix Fietkau <nbd@nbd.name>
4 months agoath79: correct Siemens WS-AP3610 blocksize
David Bauer [Thu, 20 Feb 2020 09:29:09 +0000 (10:29 +0100)]
ath79: correct Siemens WS-AP3610 blocksize

With the wrong blocksize, the rootfs was not positioned on the boundary
of a block, thus breaking the mtdsplit driver.

Signed-off-by: David Bauer <mail@david-bauer.net>
4 months agoppp: backport security fixes
Petr Štetiar [Thu, 20 Feb 2020 08:03:54 +0000 (09:03 +0100)]
ppp: backport security fixes

8d45443bb5c9 pppd: Ignore received EAP messages when not doing EAP
8d7970b8f3db pppd: Fix bounds check in EAP code
858976b1fc31 radius: Prevent buffer overflow in rc_mksid()

Signed-off-by: Petr Štetiar <ynezz@true.cz>
4 months agoutil-linux: Update to 2.35.1
Daniel Engberg [Mon, 3 Feb 2020 17:11:35 +0000 (17:11 +0000)]
util-linux: Update to 2.35.1

Update util-linux to 2.35.1 and refresh patches.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[commit subject and description tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
4 months agoath79: add label MAC address for Ubiquiti Picostation M (XM)
Adrian Schmutzler [Wed, 19 Feb 2020 22:34:41 +0000 (23:34 +0100)]
ath79: add label MAC address for Ubiquiti Picostation M (XM)

This adds the label MAC address for the Ubiquiti Picostation M (XM).
This was overlooked when adding support in the previous patch.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agoath79: add support for Ubiquiti Picostation M (XM)
Adrian Schmutzler [Mon, 17 Feb 2020 23:08:18 +0000 (00:08 +0100)]
ath79: add support for Ubiquiti Picostation M (XM)

This adds support for the Ubiquiti Picostation M (XM), which has the
same board/LEDs as the Bullet M XM, but different case and antennas.

Specifications:
- AR7241 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- External antenna: 5 dBi (USA), 2 dBi (EU)
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB

Flashing via WebUI:
  Upload the factory image via the stock firmware web UI.

  Attention: airOS firmware versions >= 5.6 have a new bootloader with
  an incompatible partition table!

  Please downgrade to <= 5.5 _before_ flashing OpenWrt!
  Refer to the device's Wiki page for further information.

Flashing via TFTP:
  Same procedure as other NanoStation M boards.

- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
  button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
  LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
  $ tftp 192.168.1.20
  tftp> bin
  tftp> trace
  tftp> put openwrt-ath79-generic-xxxxx-ubnt_picostation-m-squashfs-factory.bin

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agoath79: add support for Ubiquiti Nanostation Loco M (XM)
Sven Roederer [Mon, 17 Feb 2020 11:22:53 +0000 (12:22 +0100)]
ath79: add support for Ubiquiti Nanostation Loco M (XM)

This adds support for the Ubiquiti Nanostation Loco M (XM), which
has the same board/LEDs as the Bullet M XM, but different case and
antennas.

Specifications:
- AR7241 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- NS Loco M2: built-in antenna: 8 dBi; AR9287
- NS Loco M5: built-in antenna: 13 dBi; 2T2R 5 GHz radio
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB

Flashing via WebUI:
  Upload the factory image via the stock firmware web UI.
  Note that only certain firmware versions accept unsigned
  images. Refer to the device's Wiki page for further information.

Flashing via TFTP:
  Same procedure as other NanoStation M boards.

- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
  button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
  LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
  $ tftp 192.168.1.20
  tftp> bin
  tftp> trace
  tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanostation-loco-m-squashfs-factory.bin

Tested on NanoStation Loco M2.

Signed-off-by: Sven Roederer <freifunk@it-solutions.geroedel.de>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agoath79: move TPLINK_HWID/_HWREV to parent for tplink-safeloader
Adrian Schmutzler [Sun, 16 Feb 2020 09:40:53 +0000 (10:40 +0100)]
ath79: move TPLINK_HWID/_HWREV to parent for tplink-safeloader

Several devices with tplink-safeloader contain default values (0x0)
for TPLINK_HWID and TPLINK_HWREV in their device definitions.
Move those to common tplink-safeloader definition so they do not
have to be repeated each time.

While at it, set default value for tplink-v1 and tplink-v2 as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
4 months agomt76: update to the latest version
Felix Fietkau [Wed, 19 Feb 2020 21:12:04 +0000 (22:12 +0100)]
mt76: update to the latest version

bd0df1b017a8 mt76: avoid extra RCU synchronization on station removal
d5a5e97b67c7 mt76: mt76x2: avoid starting the MAC too early
a67e42990d8a mt76: mt7615: fix msdu_id endianness in mt7615_write_hw_txp
d3af8bd3c722 mt76: mt7615: set proper length in strncmp
9c43417db17c mt76: mt7615: fix max_nss in mt7615_eeprom_parse_hw_cap
764e1d208a06 mt76: mt7615: fix tx power reporting
1881241c7ee5 mt76: fix rounding issues on converting per-chain and combined txpower
fa14e7f33199 mt76: mt7615: rework rx phy index handling
a205ce3e3e2d mt76: mt7615: fix ext_phy flag for stations
457a93203690 mt76: mt7615: fix MT_TX_HW_QUEUE_EXT_PHY to deal with mac80211 changes
c75cf513c674 mt76: do not set HOST_BROADCAST_PS_BUFFERING for mt7615
cc56c400167c mt76: fix LED link time failure
4dbd56b86970 mt76: mt76x0u: add support to TP-Link T2UHP
e226309c4bc4 mt76: mt7615: rely on mt76_queues_read for mt7622
c6a025318075 mt76: mt76u: extend RX scatter gather number
dfc24bc504e3 mt76: mt76u: rename stat_wq in wq
2bbffd2cb37b mt76: mt7615: remove rx_mask in mt7615_eeprom_parse_hw_cap
f408a2b7566c mt76: Introduce mt76_mcu data structure
17ecf0762542 mt76: mt76x02: fix handling MCU timeouts during hw restart
284e9fd72912 mt76: mt7615: fix monitor injection of beacon frames
8f8e9161b355 mt76: fix array overflow on receiving too many fragments for a packet

Signed-off-by: Felix Fietkau <nbd@nbd.name>
4 months agokernel: avoid underscore in *6lowpan package names
Eneas U de Queiroz [Tue, 18 Feb 2020 20:47:20 +0000 (17:47 -0300)]
kernel: avoid underscore in *6lowpan package names

Packages kmod-bluetooth_6lowpan and kmod-ieee802154_6lowpan contain an
underscore in the package name.  This causes problems in package/install
because when building a list of package files to install offline using
opkg, it uses a wildcard of the form $(dir)/$(pkg)_*.ipk.

If you were to select kmod-bluetooth=y, but kmod-bluetooth_6lowpan=m,
the latter would be picked up by that wildcard, and make package/install
would fail:

Collected errors:
 * satisfy_dependencies_for: Cannot satisfy the following dependencies
 * for kmod-bluetooth_6lowpan:
 *      kmod-6lowpan
 * opkg_install_cmd: Cannot install package kmod-bluetooth_6lowpan.

Changing the wildcard pattern is not trivial, and there may be other
places in the build system making this assumption about the package name
format.

Using a dash in place of the underscore avoids the issue.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
4 months agodnsmasq: fix uci-defaults script to exit 0 so it is cleaned up
Russell Senior [Tue, 18 Feb 2020 06:16:10 +0000 (22:16 -0800)]
dnsmasq: fix uci-defaults script to exit 0 so it is cleaned up

A file, package/network/services/dnsmasq/files/50-dnsmasq-migrate-resolv-conf-auto.sh,
was added in commit 6a2855212096d2c486961a0841b037bae4b75de7, but it
does not exit in a way that tells the uci-defaults mechanism that it
succeeded, and so it is not cleaned up after running successfully. Add
an exit 0 to the end to correct that.

Signed-off-by: Russell Senior <russell@personaltelco.net>
4 months agotools/bison: Update to 3.5.1
Daniel Engberg [Mon, 3 Feb 2020 13:30:01 +0000 (13:30 +0000)]
tools/bison: Update to 3.5.1

Update bison to 3.5.1
Use POSIX threads as the previous option is no longer valid
Disable NLS support to be consistent with other tools such as e2fsprogs and sed

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
4 months agotools/e2fsprogs: Update to 1.45.5
Daniel Engberg [Mon, 3 Feb 2020 13:21:56 +0000 (13:21 +0000)]
tools/e2fsprogs: Update to 1.45.5

Update e2fsprogs to 1.45.5
Enable pthreads support

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
4 months agotools/gmp: Remove obsolete options
Daniel Engberg [Mon, 3 Feb 2020 13:04:07 +0000 (13:04 +0000)]
tools/gmp: Remove obsolete options

Remove mpbsd argument

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
4 months agotools/sed: Update to 4.8
Daniel Engberg [Mon, 3 Feb 2020 13:09:49 +0000 (13:09 +0000)]
tools/sed: Update to 4.8

Update sed to 4.8
Use POSIX threads
Disable i18n and selinux support

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
4 months agotools/patchelf: Update to 0.10
Daniel Engberg [Mon, 3 Feb 2020 13:13:27 +0000 (13:13 +0000)]
tools/patchelf: Update to 0.10

Update patchelf to 0.10

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
4 months agotools/libressl: Update to 3.0.2
Daniel Engberg [Mon, 3 Feb 2020 15:47:47 +0000 (15:47 +0000)]
tools/libressl: Update to 3.0.2

Update libressl to 3.0.2 and remove 010-avoid-glibc.patch as fix is added by upstream

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
4 months agoath79: add gpio4 pinmux on TL-WR841N/ND v8, WR842N v2, MR3420 v2
Adrian Schmutzler [Thu, 30 Jan 2020 13:59:25 +0000 (14:59 +0100)]
ath79: add gpio4 pinmux on TL-WR841N/ND v8, WR842N v2, MR3420 v2

This adds a pinmux to the shared DTSI for TP-Link TL-WR841N/ND v8,
TL-WR842N v2 and TL-MR3420 v2. It is supposed to be the equivalent
of:

/* config gpio4 as normal gpio function */
ath79_gpio_output_select(TL_MR3420V2_GPIO_USB_POWER,AR934X_GPIO_OUT_GPIO);

This allows to enable USB power on these devices.

While at it, move the jtag_disable_pins to &gpio node and remove the
redundant status=okay there.

Tested on TP-Link TL-WR842N v2.

Fixes: FS#2753

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Armin Fuerst <armin@fuerst.priv.at>