openwrt/openwrt.git
2 years agouboot-lantiq: Add BT Home Hub 5A support
Mathias Kresin [Fri, 20 May 2016 21:45:59 +0000 (23:45 +0200)]
uboot-lantiq: Add BT Home Hub 5A support

Based on the submission to the uboot-lantiq repo by Martin Blumenstingl.

Use the ddr_settings.h from the GPL tarball. The NAND boot optimized
one (with memory tuning enabled) doesn't work for the UART boot image.

Use the same mtd layout as the stock u-boot. Add add UBI support.

Use the leds to indicate boot status like it is done with the stock
u-boot. Switch on the red power led if kernel image can't be loaded.
Otherwise switch the green led on.

Make only the ramboot u-boot available. Only this image is required for
the first installation of LEDE.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agolantiq: use BT HomeHub 5 Type A OEM partition layout
Mathias Kresin [Sat, 3 Oct 2015 11:57:54 +0000 (13:57 +0200)]
lantiq: use BT HomeHub 5 Type A OEM partition layout

This way the on nand bad block table is preserved and used. Add support
for nand OOB ECC checksums as well. It should fix all reported ubi
errors, which were all related to bad nand blocks and a purged on nand
bad block table.

The existing ubi partition will be reused, which eliminates the need
to touch the caldata during initial install. The BT u-boot has support
for loading a kernel from an ubi volume. It isn't necessary any longer
to replace the BT u-boot with a custom compiled one to use LEDE.

It is required to restore the BT Firmware and install LEDE from scratch
to switch to the new partition layout.

An image for restoring the BT firmware and installing LEDE is provided
at https://github.com/mkresin/lede/releases.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agolantiq: backport kernel patch to pass of node to nand_dt_init
Mathias Kresin [Tue, 31 May 2016 06:39:53 +0000 (08:39 +0200)]
lantiq: backport kernel patch to pass of node to nand_dt_init

Backport upstream commit a61ae81a1907af1987ad4c77300508327bc48b23.

The actually purpose of the patch was to do some cleanup. As a side
effect of this cleanup, the device node is now passed to nand_dt_init.

This allows to use the common nand device tree properties

 - nand-bus-width
 - nand-on-flash-bbt
 - nand-ecc-mode
 - nand-ecc-step-size
 - nand-ecc-strength

for the plat_nand driver.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agolantiq: drop ath9k device tree binding & ath9k pci fixup
Mathias Kresin [Sat, 6 Aug 2016 07:19:45 +0000 (09:19 +0200)]
lantiq: drop ath9k device tree binding & ath9k pci fixup

Due to the addition of the bindings to the ath9k driver, this code
isn't used any longer. The fixup is now done by the owloader.

Rename the ath_eep.c file to ath5k_eep.c to indicate that this files
includes ath5k related code only.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agolantiq: use ath9k device tree bindings binding/owl-loader
Martin Blumenstingl [Sat, 26 Nov 2016 00:01:15 +0000 (01:01 +0100)]
lantiq: use ath9k device tree bindings binding/owl-loader

This moves the extraction of the eeprom/calibration data to a hotplug
firmware script. Additionally it modifies all .dts to configure ath9k
directly from within the .dts.

The owl-loader approach enables support on devices with exotic eeprom
data locations (such as unaligned positions on the flash or data
inside an UBI volume).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[add ath9k caldata mac address patcher]
[fixes DGN3500 wifi mac]
[fixes BTHOMEHUBV3A wifi mac]
[set invalid mac for BTHOMEHUB2B, FRITZ3370, FRITZ7320 & FRITZ7360SL to restore previous random mac behavior]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agokernel: mac80211: disable ath9k bands via device tree
Martin Blumenstingl [Sat, 26 Nov 2016 00:01:14 +0000 (01:01 +0100)]
kernel: mac80211: disable ath9k bands via device tree

These properties allow overriding the settings from the EEPROM
which indicate whether a band is enabled or not.
Setting this property is only needed when the RF circuit does not
support the 2.4GHz or 5GHz band while it is enabled nevertheless in the
EEPROM.

These patches will be replaced with a future upstream version which
will introduces an ieee80211 device tree property to disable bands.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2 years agokernel: mac80211: add pending ath9k EEPROM swapping patches
Martin Blumenstingl [Sat, 26 Nov 2016 00:01:13 +0000 (01:01 +0100)]
kernel: mac80211: add pending ath9k EEPROM swapping patches

There are two types of swapping the EEPROM data in the ath9k driver.
Before this series one type of swapping could not be used without the
other.

The first type of swapping looks at the "magic bytes" at the start of
the EEPROM data and performs swab16 on the EEPROM contents if needed.
The second type of swapping is EEPROM format specific and swaps
specific fields within the EEPROM itself (swab16, swab32 - depends on
the EEPROM format).

With this series the second part now looks at the EEPMISC register
inside the EEPROM, which uses a bit to indicate if the EEPROM data
is Big Endian (this is also done by the FreeBSD kernel).
This has a nice advantage: currently there are some out-of-tree hacks
(in OpenWrt and LEDE) where the EEPROM has a Big Endian header on a
Big Endian system (= no swab16 is performed) but the EEPROM itself
indicates that it's data is Little Endian. Until now the out-of-tree
code simply did a swab16 before passing the data to ath9k, so ath9k
first did the swab16 - this also enabled the format specific swapping.
These out-of-tree hacks are still working with the new logic, but it
is recommended to remove them. This implementation is based on a
discussion with Arnd Bergmann who raised concerns about the
robustness and portability of the swapping logic in the original OF
support patch review, see [0].

After a second round of patches (= v1 of this series) neither Arnd
Bergmann nor I were really happy with the complexity of the EEPROM
swapping logic. Based on a discussion (see [1] and [2]) we decided
that ath9k should use a defined format (specifying the endianness
of the data - I went with __le16 and __le32) when accessing the
EEPROM fields. A benefit of this is that we enable the EEPMISC based
swapping logic by default, just like the FreeBSD driver, see [3]. On
the devices which I have tested (see below) ath9k now works without
having to specify the "endian_check" field in ath9k_platform_data (or
a similar logic which could provide this via devicetree) as ath9k now
detects the endianness automatically. Only EEPROMs which are mangled
by some out-of-tree code still need the endian_check flag (or one can
simply remove that mangling from the out-of-tree code).

[0] http://www.spinics.net/lists/linux-wireless/msg152634.html
[1] https://marc.info/?l=linux-wireless&m=147250597503174&w=2
[2] https://marc.info/?l=linux-wireless&m=147254388611344&w=2
[3] https://github.com/freebsd/freebsd/blob/50719b56d9ce8d7d4beb53b16e9edb2e9a4a7a18/sys/dev/ath/ath_hal/ah_eeprom_9287.c#L351

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2 years agokernel: mac80211: backport ath9k device tree support patches
Martin Blumenstingl [Sat, 26 Nov 2016 00:01:12 +0000 (01:01 +0100)]
kernel: mac80211: backport ath9k device tree support patches

These patches add support for configuring ath9k based devices via
devicetree. This was tested on PCI(e) based devices. This should work
for AHB based devices as well (adding more AHB specific properties may
still be needed) as soon as the ath79 platform is ready to populate the
ath9k wmac via devicetree.
This patchset was accepted upstream, more information can be found on
the linux-wireless list:
https://www.spinics.net/lists/linux-wireless/msg155474.html

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2 years agoar71xx: fix syntax error in /lib/ar71xx.sh
Matthias Schiffer [Tue, 29 Nov 2016 18:53:27 +0000 (19:53 +0100)]
ar71xx: fix syntax error in /lib/ar71xx.sh

Remove all comments in ubnt_xm_board_detect(), as it's not possible to add
comments to specific lines of the case construct anyways.

Fixes: 9a5801e7 "ar71xx: add model detection for UBNT Rocket Ti"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agoar71xx: add model detection for UBNT Rocket Ti
Matthias Schiffer [Tue, 29 Nov 2016 14:35:46 +0000 (15:35 +0100)]
ar71xx: add model detection for UBNT Rocket Ti

Based-on-patch-by: Neal Oakey <neal.oakey@bingo-ev.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agokernel: have kmod-ipsec depend on kmod-crypto-echainiv
Stijn Tintel [Thu, 17 Nov 2016 14:33:20 +0000 (15:33 +0100)]
kernel: have kmod-ipsec depend on kmod-crypto-echainiv

The ESP algorithms in CBC mode require echainiv, so have kmod-ipsec
depend on kmod-crypto-echainiv.

See upstream commit 32b6170ca59ccf07d0e394561e54b2cd9726038c.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2 years agobrcm47xx: fix initramfs image build error
Felix Fietkau [Fri, 25 Nov 2016 12:10:38 +0000 (13:10 +0100)]
brcm47xx: fix initramfs image build error

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agobrcm47xx: merge cpu cache workaround patches into one, ensure they get compiled out...
Felix Fietkau [Fri, 25 Nov 2016 12:09:58 +0000 (13:09 +0100)]
brcm47xx: merge cpu cache workaround patches into one, ensure they get compiled out on mips74k

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoar71xx: remove squashfs-64k rootfs image from bin directory, the generic one is enough
Felix Fietkau [Tue, 29 Nov 2016 08:58:33 +0000 (09:58 +0100)]
ar71xx: remove squashfs-64k rootfs image from bin directory, the generic one is enough

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoar71xx: remove split kernel/rootfs images where the sysupgrade image can be written...
Felix Fietkau [Tue, 29 Nov 2016 09:05:46 +0000 (10:05 +0100)]
ar71xx: remove split kernel/rootfs images where the sysupgrade image can be written to flash directly

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoar71xx: remove 2MB flash variant of WP543
Felix Fietkau [Tue, 29 Nov 2016 08:54:53 +0000 (09:54 +0100)]
ar71xx: remove 2MB flash variant of WP543

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoar71xx: remove legacy devices that cannot be supported due to kernel partition size...
Felix Fietkau [Tue, 29 Nov 2016 08:43:36 +0000 (09:43 +0100)]
ar71xx: remove legacy devices that cannot be supported due to kernel partition size limits

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoar71xx: remove legacy gzip images
Felix Fietkau [Wed, 23 Nov 2016 09:27:17 +0000 (10:27 +0100)]
ar71xx: remove legacy gzip images

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoar71xx: remove obsolete jffs2 image building code
Felix Fietkau [Wed, 23 Nov 2016 09:21:07 +0000 (10:21 +0100)]
ar71xx: remove obsolete jffs2 image building code

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoiw: drop TX power patch that is part of upstream version now
Rafał Miłecki [Tue, 29 Nov 2016 07:38:24 +0000 (08:38 +0100)]
iw: drop TX power patch that is part of upstream version now

Applying it again was resulting in duplicated TX info like:
Interface wlan0
        ifindex 6
        wdev 0x1
        addr 00:23:6a:a3:7d:00
        ssid LEDE2
        type AP
        wiphy 0
        channel 11 (2462 MHz), width: 20 MHz, center1: 2462 MHz
        txpower 31.00 dBm
        txpower 31.00 dBm

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2 years agokernel: use upstream accepted bcm47xxpart parsing fix
Rafał Miłecki [Mon, 28 Nov 2016 12:14:35 +0000 (13:14 +0100)]
kernel: use upstream accepted bcm47xxpart parsing fix

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2 years agobcm53xx: use upstream accepted fix for ARM core aborts
Rafał Miłecki [Mon, 28 Nov 2016 12:07:29 +0000 (13:07 +0100)]
bcm53xx: use upstream accepted fix for ARM core aborts

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2 years agofirmware-utils: replace md5 code with Alexander Peslyak's implementation
Rafał Miłecki [Sat, 19 Nov 2016 20:09:53 +0000 (21:09 +0100)]
firmware-utils: replace md5 code with Alexander Peslyak's implementation

Our current implementation is pretty old and uses some pre-standard/old
ANSI C style that triggers warnings like:
warning: call to function 'MD5_Init' without a real prototype [-Wunprototyped-calls]

This is caused by declarations specified in a following way:
src/md5.h:60:6: note: 'MD5_Init' was declared here
 void MD5_Init ();

Having these warnings makes it harded to notice real problems. We could
try hiding them but it makes more sense to just use a cleaner code.
Another tiny gain from this switch is slightly reduced binary size, on
x86_64 tplink-safeloader's size 48104 became 48003.

The new code is public domain, uses "heavily cut-down BSD license".

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2 years agolantiq: add Falcon support
Hauke Mehrtens [Sun, 2 Oct 2016 16:39:50 +0000 (18:39 +0200)]
lantiq: add Falcon support

This adds support for the Intel Falcon SoC for GPON.

Support for the Falcon SoC was removed in commit c8218363951 svn rev:
40392 from OpenWrt, this commit adds it again.

This patch adds a new subtarget for the Falcon SoC, but it still misses
all the drivers needed to control the GPON part.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agolantiq: add swconfig to the default packages
Mathias Kresin [Sun, 27 Nov 2016 13:59:20 +0000 (14:59 +0100)]
lantiq: add swconfig to the default packages

The DEVICE_PACKAGES are not included in the initramfs image in case
TARGET_PER_DEVICE_ROOTFS is set. This might produces initramfs images
with a not working network configuration because of a missing swconfig.

Workaround the issues by adding the essential swconfig package to the
default packages selection and deselect swconfig for boards not having
swconfig included before via device packages.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agoltq-hcd: drop package
Mathias Kresin [Sun, 27 Nov 2016 12:15:23 +0000 (13:15 +0100)]
ltq-hcd: drop package

Since ffd7c155008bff4b08197dfd710d7a1386313f98 it isn't used anymore on
any supported target.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agogpio-button-hotplug: add more buttons
Mathias Kresin [Wed, 19 Oct 2016 19:08:14 +0000 (21:08 +0200)]
gpio-button-hotplug: add more buttons

The keycodes are used by some boards.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agotreewide: fix button keys codes used in dts
Mathias Kresin [Sun, 27 Nov 2016 08:47:51 +0000 (09:47 +0100)]
treewide: fix button keys codes used in dts

Use keycodes that matches the intended use case based on the label.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agoramips: add size checks/append metadata where missing
Mathias Kresin [Sat, 26 Nov 2016 09:43:34 +0000 (10:43 +0100)]
ramips: add size checks/append metadata where missing

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agoramips: fix Airlink AR670W factory image
Mathias Kresin [Fri, 25 Nov 2016 12:03:01 +0000 (13:03 +0100)]
ramips: fix Airlink AR670W factory image

Move the mkwrgimg build step to the makefile. It will be required by
other boards as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agomvebu: fix typo in image metadata support
Mathias Kresin [Fri, 25 Nov 2016 16:44:24 +0000 (17:44 +0100)]
mvebu: fix typo in image metadata support

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agoipq806x: more dts cleanup
Mathias Kresin [Sat, 26 Nov 2016 09:20:03 +0000 (10:20 +0100)]
ipq806x: more dts cleanup

Remove the wifi5g LED from the the d7800, r7500 and r7800. Albeit this
GPIO is mentioned in the GPL tarball, it doesn't do anything. The
2.4/5 GHz LEDs are connected to the wifi chips and not be controlled
from the the userspace.

Use the LEDs names/colours as they are used in the board manuals. Merge
redundant LED configurations. Use the phy[0|1]tpt trigger for the
wireless LEDs. Remove the workarounds for the not controllable wireless
LEDs.

Fix spi compatible strings and remove superfluous spi-max-frequency
parameters.

If there are two power leds, use one for indicating normal operation and
one for failsafe/upgrade. Keep the on/off state of the main power led
during boot.

Use the usb pinmux settings from the nbg6817 gpl sources.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agoipq806x: clean up dts files
Henryk Heisig [Mon, 21 Nov 2016 20:04:52 +0000 (21:04 +0100)]
ipq806x: clean up dts files

Set the pinmux to the values found in the GPL tarballs of the boards.
Remove pinmux which are is not used (like nand pinmux for spi
flash boards).

This allows to use the wan orange led of the C2600 which had a wrong
pinmux before. Might fix buttons or leds of other boards as well.

Fix the LED color and the ledswitch key code of the C2600. Rename the
ledgnr to ledswitch.

Add support for indication the boot state using LEDs to the D7800,
NBG6817, R7500 and R7500v2.

Change GPIO active to readable values in D7800, EA8500, R7500,
R7500v2 and R7800.

Change gpioexport to gpio pinmux.

Add proper "drive strenght" to i2c4_pins and use it for RPM on
C2600, D7800, EA8500, R7500, R7500v2.

Remove pcie pinmux from D7800.

Move pinctrl to correct place in NBG6817 and R7800.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2 years agofirmware-utils: Fix build failure in mkmerakifw.c FS#298
Florian Fainelli [Wed, 23 Nov 2016 20:50:25 +0000 (12:50 -0800)]
firmware-utils: Fix build failure in mkmerakifw.c FS#298

Earlier compilers such as GCC 4 do not like anynomous unions, make it a named
union "u", and update the code where relevant.

Fixes FS#298
Fixes: a72e1692b8b3 ("firmware-utils: Add support for the Cisco Meraki MX60/MX60W")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2 years agoipset: Add InstallDev to provide libipset as library
Julian Kornberger [Sat, 26 Nov 2016 10:15:34 +0000 (11:15 +0100)]
ipset: Add InstallDev to provide libipset as library

2 years agolantiq: specify the PCIe controller's interrupt, size and address cells
Martin Blumenstingl [Sat, 26 Nov 2016 00:01:11 +0000 (01:01 +0100)]
lantiq: specify the PCIe controller's interrupt, size and address cells

This allows adding devices to the PCIe controller in the .dts files.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2 years agolantiq: Register the device tree node with the PCIe controller
Martin Blumenstingl [Sat, 26 Nov 2016 00:01:10 +0000 (01:01 +0100)]
lantiq: Register the device tree node with the PCIe controller

This allows specifying PCI devices as children of the PCIe controller
node to pass configuration data to them.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2 years agoramips: Add missing chunked-io directive to W2914NSV2.dtsi
Yong-hyu, Ban [Sat, 26 Nov 2016 12:20:14 +0000 (21:20 +0900)]
ramips: Add missing chunked-io directive to W2914NSV2.dtsi

Fix bug that LEDE failed to boot with this message:

WARNING: CPU: 2 PID: 1 at drivers/spi/spi-mt7621.c:214
mt7621_spi_transfer_one_message+0x28c/0x620()

Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
2 years agoramips: SamKnows SK-WB8 DTS cleanup
Andrew Yong [Mon, 21 Nov 2016 15:24:57 +0000 (23:24 +0800)]
ramips: SamKnows SK-WB8 DTS cleanup

Use gpio.h definition of GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW. Remove unused backup partition to increase available JFFS space. As long as U-Boot env variable "bootcount" is < 3 (reset to 0 after boot by init script) SamKnow's U-Boot will not attempt to boot from the backup flash address (0xe30000).

Signed-off-by: Andrew Yong <me@ndoo.sg>
2 years agokernel: fix typo in input-gpio-encoder package title
Avi H. D [Thu, 24 Nov 2016 20:49:35 +0000 (02:19 +0530)]
kernel: fix typo in input-gpio-encoder package title

Line 115, 'rotary' was misspelled as 'rotay'

Signed off by: Avinash Duduskar <strykar@hotmail.com>

2 years agotools/cmake: update to 3.7.0
Hannu Nyman [Fri, 25 Nov 2016 14:10:09 +0000 (16:10 +0200)]
tools/cmake: update to 3.7.0

Release notes at
https://cmake.org/cmake/help/v3.7/release/3.7.html

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2 years agotools/quilt: update to 0.65
Hannu Nyman [Fri, 25 Nov 2016 14:08:31 +0000 (16:08 +0200)]
tools/quilt: update to 0.65

User-visible changes since 0.64 are as follows:

  - Translation fixes
  - Project settings have priority
  - Reject binary files in patches
  - Fix a race condition in diff_file
  - Performance: Optimizations to the setup command
  - Performance: Optimizations to the bash completion script
  - Test suite: Improve the edit test case
  - Test suite: Make the symlink test more robust
  - Test suite: Test backup failure
  - Test suite: Test the header command with hard links
  - diff: Report diff failures
  - edit: Fix a corner case bug
  - mail: Fix the help text
  - push: Fix the synopsis
  - refresh: Do not remove symlinks
  - refresh: Break links to read-only patch files
  - refresh: Always preserve modification time
  - setup: Report failed look-ups in inspect-wrapper
  - quilt.el: Fix quilt-editable when patches are stored in subdirs
  - bash_completion: Handle spaces in file names
  - bash_completion: Update the list of commands
  - bash_completion: Add new command options
  - bash_completion: Fix handling of mail, new, push options
  - guards: Simplify the help text
  - guards: Include the file name also in the "Not found" case
  - guards: Add support for an external filelist in --check mode
  - guards: Report which config file has problem in --check mode
  - guards: Documentation update
  - guards: Clarify a user message

Note to packagers: the Makefile was modified to take configure's
--sysconfdir into account as other projects do. As a result, setting
--prefix=/usr will no longer put the configuration files under /etc.
You now need to explicitly pass --sysconfdir=/etc. If you don't,
configuration files will go under /usr/etc, which is not what you want.
This is somewhat less intuitive, but also more consistent with what
other projects are doing.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2 years agotools/scons: update to 2.5.1
Hannu Nyman [Fri, 25 Nov 2016 14:07:11 +0000 (16:07 +0200)]
tools/scons: update to 2.5.1

RELEASE 2.5.1 - Mon, 03 Nov 2016 13:37:42 -0400
    - Add scons-configure-cache.py to packaging. It was omitted
    - Use memoization to optimize PATH evaluation across
      all dependencies per node.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2 years agoRevert "mvebu: simplify etc/board.d/02_network"
Felix Fietkau [Fri, 25 Nov 2016 19:02:56 +0000 (20:02 +0100)]
Revert "mvebu: simplify etc/board.d/02_network"

This reverts commit 539ae47103b7de5cecb1a94beab0acb97ef7df1d.
According to reports, this introduces a regression on WRT3200ACM

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoramips: remove kmod-ledtrig-usbdev from recently added devices
Mathias Kresin [Thu, 24 Nov 2016 07:03:22 +0000 (08:03 +0100)]
ramips: remove kmod-ledtrig-usbdev from recently added devices

None of the devices uses an usb led at all.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agoar71xx: move DomyWifi DW33D to nand subtarget
Piotr Dymacz [Wed, 23 Nov 2016 15:34:31 +0000 (16:34 +0100)]
ar71xx: move DomyWifi DW33D to nand subtarget

This device uses NAND FLASH, so it should be kept in nand subtarget.

Also, inlcude in packages kmod-usb-ledtrig-usbport instead of
obsolete kmod-ledtrig-usbdev.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agoipq806x: add support for TP-Link Archer VR2600v
Sebastian Quilitz [Wed, 23 Nov 2016 17:51:15 +0000 (18:51 +0100)]
ipq806x: add support for TP-Link Archer VR2600v

This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.

It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.

To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.

Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
2 years agoremove bogus dev/null that was accidentally introduced while applying a patch
Felix Fietkau [Thu, 24 Nov 2016 12:42:58 +0000 (13:42 +0100)]
remove bogus dev/null that was accidentally introduced while applying a patch

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agokernel: remove another redundant KCONFIG entry in virt.mk
Felix Fietkau [Thu, 24 Nov 2016 12:41:10 +0000 (13:41 +0100)]
kernel: remove another redundant KCONFIG entry in virt.mk

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agokernel: fix virtualization kmod dependencies and kconfig symbols
Felix Fietkau [Thu, 24 Nov 2016 12:29:05 +0000 (13:29 +0100)]
kernel: fix virtualization kmod dependencies and kconfig symbols

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agokernel: remove kmod-vhost_net, fixes build breakage
Felix Fietkau [Thu, 24 Nov 2016 12:26:04 +0000 (13:26 +0100)]
kernel: remove kmod-vhost_net, fixes build breakage

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agosunxi: enable CONFIG_VHOST_NET like on x86
Felix Fietkau [Thu, 24 Nov 2016 12:25:15 +0000 (13:25 +0100)]
sunxi: enable CONFIG_VHOST_NET like on x86

Other virtualization options are already enabled, so this is only a
small addition

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agokernel: add missing config symbols
Felix Fietkau [Thu, 24 Nov 2016 12:15:14 +0000 (13:15 +0100)]
kernel: add missing config symbols

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agolibnl-tiny: Remove GENL_ID_GENERATE
Florian Fainelli [Wed, 23 Nov 2016 23:13:18 +0000 (15:13 -0800)]
libnl-tiny: Remove GENL_ID_GENERATE

This constant was always defined to 0, and recently got removed in
upstream commit a07ea4d9941af5a0c6f0be2a71b51ac9c083c5e5 ("genetlink: no
longer support using static family IDs")

Fixes libnl-tiny builds with latest upstream kernels.

Fixes: d723f2573af3 ("libnl-tiny: remove include/linux overrides to fix various build issues")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2 years agotarget: sunxi: enable builtin crypto-hw module sun4i-ss
Yousong Zhou [Thu, 24 Nov 2016 05:50:03 +0000 (13:50 +0800)]
target: sunxi: enable builtin crypto-hw module sun4i-ss

CONFIG_CRYPTO_DEV_SUN4I_SS was previously set to y but did not take
effect because of the absence of CONFIG_CRYPTO_HW=y

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2 years agobuild: find_md5: ignore non-existent files or directories
Yousong Zhou [Thu, 24 Nov 2016 05:50:02 +0000 (13:50 +0800)]
build: find_md5: ignore non-existent files or directories

Targets like malta can have no patches/ directory available and this
commit tries quash "no such file or directory" messages from `find`

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2 years agoapm821xx: make it possible to update the dtb partition on the WNDR4700
Christian Lamparter [Wed, 23 Nov 2016 16:17:05 +0000 (17:17 +0100)]
apm821xx: make it possible to update the dtb partition on the WNDR4700

Currently, the device-tree partition is marked as read-only.
Hence, userspace tools like mtd can't write into the partition.
This however will be necessary in case the DTB needs to be
updated.

This patch also adds the kernel.dtb image, so the compiled
DTB is exported as a file and available in the binary
directory along the firmware images.

Note: the u-boot does expects the dtb to be a uimage.

To update the dtb manually:
 1. copy the generated dtb to the router.
 2. mtd erase /dev/mtd2
 3. mtd write wndr4700.dtb /dev/mtd2

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agotarget: sunxi: enable kvm support
Yousong Zhou [Wed, 23 Nov 2016 16:03:41 +0000 (00:03 +0800)]
target: sunxi: enable kvm support

Unlike x86, kvm for arm has to be built into the kernel.  The kernel
config was prepared with the following command

    make kernel_menuconfig CONFIG_TARGET=platform

Then enable ARM_LPAE, VIRTUALIZATION, KVM in that order

Other config changes are done by the build system.  The following text
tries to explain some of them, for archive purposes probably...

 - BUILD_BIN2C.  It was dropped probably because the prompt is empty and
   no other config option selects it.  bin2c is a host executable for
   converting binary content to a piece of c code for inclusion
 - CRYPTO_DEV_SUN4I_SS.  It was dropped because the dependency CRYPTO_HW
   was not enabled.  Setting that aside, packaging it as a loadbable
   module in lieu of other sunxi specific modules seems more appropriate
 - PGTABLE_LEVELS.  It was changed from 2 to 3 because 3 is the default
   when ARM_LPAE is enabled
 - HAVE_KERNEL_GZIP, etc..  These are enabled in generic config
 - SCHED_INFO, ZLIB_INFLATE.  These were dropped probably for the same
   reason as for BUILD_BIN2C

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2 years agopackage: add kernel packages for kvm virtualization
Yousong Zhou [Wed, 23 Nov 2016 16:03:40 +0000 (00:03 +0800)]
package: add kernel packages for kvm virtualization

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2 years agotoolchain: gcc: disable ifunc on *-musl by default
Yousong Zhou [Wed, 23 Nov 2016 16:03:39 +0000 (00:03 +0800)]
toolchain: gcc: disable ifunc on *-musl by default

Otherwise the built binaries may fail with

    Error relocating /usr/bin/qemu-system-x86_64: unsupported relocation type 37

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2 years agobuild: scan.mk: remove not used variable SCAN_STAMP
Yousong Zhou [Wed, 23 Nov 2016 16:03:38 +0000 (00:03 +0800)]
build: scan.mk: remove not used variable SCAN_STAMP

It was left behind since rewrite of metadata scanning done with commit
bdc9419 in July 2007

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2 years agouml: clean up the kernel config and add squashfs+ext4/f2fs support
Felix Fietkau [Tue, 22 Nov 2016 16:53:36 +0000 (17:53 +0100)]
uml: clean up the kernel config and add squashfs+ext4/f2fs support

Replaces plain ext4 images

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agopackage/utils/fuse: update to 2.9.7
Paul Wassi [Tue, 22 Nov 2016 08:43:24 +0000 (09:43 +0100)]
package/utils/fuse: update to 2.9.7

Update fuse+libfuse to upstream 2.9.7. Drop the patch for CVE-2015-3202,
which is already integrated in the newer version. Rework the other patches.
Also switch PKG_SOURCE from @SF to libfuse's github releases.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2 years agomvebu: simplify etc/board.d/02_network
Paul Wassi [Fri, 28 Oct 2016 18:22:22 +0000 (20:22 +0200)]
mvebu: simplify etc/board.d/02_network

Unify switch configuration on Linksys WRTxx00AC series.
LAN = eth0, WAN = eth1

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2 years agomvebu: use image metadata for firmware validation
Felix Fietkau [Mon, 21 Nov 2016 10:59:37 +0000 (11:59 +0100)]
mvebu: use image metadata for firmware validation

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agolantiq: write protect vgv7519 u-boot and u-boot-env partitions
Eddi De Pieri [Tue, 22 Nov 2016 09:41:18 +0000 (10:41 +0100)]
lantiq: write protect vgv7519 u-boot and u-boot-env partitions

Signed-off-by: Eddi De Pieri <eddi@depieri.net>
2 years agouboot-envtools: make it not shared
Eddi De Pieri [Mon, 21 Nov 2016 23:04:48 +0000 (00:04 +0100)]
uboot-envtools: make it not shared

uboot-envtools have some stuff related to the cpu.

This should fix following error on lantiq soc:

Downloading http://downloads.lede-project.org/snapshots/packages/mips_24kc/base/uboot-envtools_2015.10-1_mips_24kc.ipk.
Configuring uboot-envtools.
//usr/lib/opkg/info/uboot-envtools.postinst: .: line 10: can't open '/lib/ar71xx.sh'

Signed-off-by: Eddi De Pieri <eddi@depieri.net>
2 years agouboot-lantiq: vgv7519 fix tftp loading of big kernel/image size
Eddi De Pieri [Mon, 21 Nov 2016 14:59:54 +0000 (15:59 +0100)]
uboot-lantiq: vgv7519 fix tftp loading of big kernel/image size

On my board:
Bytes transferred = 7084442 (6c199a hex)
   Image Name:   MIPS OpenWrt Linux-3.10.49
   Created:      2014-11-11  17:40:00 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    7084378 Bytes = 6.8 MiB
   Load Address: 80002000
   Entry Point:  80002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... LZMA: uncompress or overwrite error
7 - must RESET b
ROM VER: 1.0.5
CFG 01

Signed-off-by: Eddi De Pieri <eddi@depieri.net>
2 years agoramips: Add device DLINK DWR-512-B
Giuseppe Lippolis [Sun, 13 Nov 2016 22:36:00 +0000 (23:36 +0100)]
ramips: Add device DLINK DWR-512-B

The Dlink DWR-512-B modem is a ralink 5350 processor based embedding
a 3G mini-pcie router.

The oem JBOOT bootloader has to be replaced by a RT5350 SDK
U-Boot such as https://github.com/stevenylai/ralink_sdk - U-Boot
configured for the RT5350 256MiB SDR.

Main reason to change the bootloader is the encrypted header used to
store the kernel image. In this way an image can only be generated
using the propietary binboy tool (included in the GPL distribution
from Dlink). The binboy tool doesn't allow to modify the kernel/rootfs
partition scheme. This is considered a big constraint (limited kernel
size and inefficient usage of flash space).

For interested people I pubblished the details of my investigation
about the encrypted firmware header here:
http://lists.infradead.org/pipermail/lede-dev/2016-October/003435.html

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2 years agoramips: do not append metadata to CY-SWR1100 factory image
Mathias Kresin [Sun, 20 Nov 2016 20:28:38 +0000 (21:28 +0100)]
ramips: do not append metadata to CY-SWR1100 factory image

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agoramips: cleanup dts files of mt7621 based boards
Mathias Kresin [Fri, 18 Nov 2016 07:39:05 +0000 (08:39 +0100)]
ramips: cleanup dts files of mt7621 based boards

Fix a typo in mt7621.dtsi compatible string. Disable spi, sdhci and pci
in mt7621.dtsi and enable the nodes in the indiviual board dts files.
The nodes require further device specific configuration anyway.

Remove the m25p80@0 spi child node from mt7621.dtsi and add the
chunked-io parameter to the individual board dts files. Fix the spi
flash compatible string for the WNDR3700V5.

Drop the mt7621-eval-board compatible string for all boards which are
not the eval board.

Drop the linux,modalias parameter from spi flash node.

Remove the xhci node from board files, it is already enabled in dtsi.
Disable xhci for boards not having usb ports populated.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agoramips: order mt7621.mk alphabetical
Mathias Kresin [Sat, 19 Nov 2016 17:27:22 +0000 (18:27 +0100)]
ramips: order mt7621.mk alphabetical

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agoath10k-ct-firmware: Update to latest firmwares.
Ben Greear [Wed, 16 Nov 2016 20:18:59 +0000 (12:18 -0800)]
ath10k-ct-firmware: Update to latest firmwares.

The 10.1 includes a good many stability fixes related to the effort of
backporting upstream 10.2 firmware.  Also enables 802.1q vlan support.
Successfully tested on apu2.

The 10.4 firmwares including new backported code as well as stability
fixes.  10.4 has been tested on Fedora x86-64 platforms, but not on LEDE
specifically since I had issues compiling LEDE for my 9980/9984 AP hardware.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2 years agoath10k-ct: Update to latest.
Ben Greear [Wed, 16 Nov 2016 20:18:58 +0000 (12:18 -0800)]
ath10k-ct: Update to latest.

Fixes locking issue, quietens some potential message floods.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2 years agonetifd: update to the latest version
Felix Fietkau [Tue, 22 Nov 2016 09:48:11 +0000 (10:48 +0100)]
netifd: update to the latest version

Fixes config reload on bridge MAC address changes

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agobrcm63xx: Livebox 1: add userspace board support
Daniel Gonzalez Cabanelas [Mon, 29 Aug 2016 14:03:49 +0000 (16:03 +0200)]
brcm63xx: Livebox 1: add userspace board support

Fix configuration files for the Livebox 1 routers.
- Add status led
- Set eth0 as the LAN port, for coherence with RedBoot and comfortability.
- Add led triggers

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2 years agobrcm63xx: Livebox 1: relocate the kernel to fix boot
Daniel Gonzalez Cabanelas [Mon, 29 Aug 2016 14:03:33 +0000 (16:03 +0200)]
brcm63xx: Livebox 1: relocate the kernel to fix boot

Fix Image generation for the Livebox 1
- missing "relocate-kernel", wrong "LOADADDR", fix it

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2 years agobrcm63xx: Livebox 1: fix part probe name
Daniel Gonzalez Cabanelas [Mon, 29 Aug 2016 14:03:14 +0000 (16:03 +0200)]
brcm63xx: Livebox 1: fix part probe name

Fix the DTS file for the Livebox 1 routers:
- part probe wrong, it should be RedBoot (uppercase matters)

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2 years agobrcm63xx: Livebox 1: fix led naming
Daniel Gonzalez Cabanelas [Mon, 29 Aug 2016 14:02:49 +0000 (16:02 +0200)]
brcm63xx: Livebox 1: fix led naming

Fix the DTS file for the Livebox 1 routers:
- leds are totally wrong, fix them.

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2 years agobrcm63xx: Livebox 1: use button 1 as failsafe button
Daniel Gonzalez Cabanelas [Mon, 29 Aug 2016 14:02:38 +0000 (16:02 +0200)]
brcm63xx: Livebox 1: use button 1 as failsafe button

Fix the DTS file for the Livebox 1 routers:
- no failsafe button, use button 1 for this purpose

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2 years agobase-files: ignore failure of stopping services on removal
Jonas Gorski [Mon, 21 Nov 2016 14:47:48 +0000 (15:47 +0100)]
base-files: ignore failure of stopping services on removal

Packages that do a killall <cmd> with the same name as the init script
will fail the prerm step when the service isn't running. Do make them
removable without having to restart the service, ignore the return code.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
2 years agoopkg: run prerm scripts for the old version also on upgrade
Jonas Gorski [Mon, 21 Nov 2016 14:20:32 +0000 (15:20 +0100)]
opkg: run prerm scripts for the old version also on upgrade

To make sure we properly restart services on upgrade we need to
call the prerm script of the old package, in case the init script
changes (or vanishes).

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
2 years agobase-files: don't modify enabled state of service on upgrade
Jonas Gorski [Mon, 21 Nov 2016 14:16:07 +0000 (15:16 +0100)]
base-files: don't modify enabled state of service on upgrade

Properly stop/start services on upgrade, but don't change the enabled
state.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
2 years agoopkg: set PKG_UPGRADE also when running scripts for the old package
Jonas Gorski [Mon, 21 Nov 2016 14:14:02 +0000 (15:14 +0100)]
opkg: set PKG_UPGRADE also when running scripts for the old package

Allow scripts from the package to be upgraded to be aware of being
upgraded.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
2 years agoRevert "grub2: add PKG_FIXUP:=autoreconf"
John Crispin [Mon, 21 Nov 2016 15:49:07 +0000 (16:49 +0100)]
Revert "grub2: add PKG_FIXUP:=autoreconf"

this caused build errors on x86

This reverts commit a0ea22ac430f91ab045431a79b2e2161e66cd56a.

Signed-off-by: John Crispin <john@phrozen.org>
2 years agoramips: fix wrong check for MT7621AT
Andrew Yong [Mon, 21 Nov 2016 16:53:00 +0000 (00:53 +0800)]
ramips: fix wrong check for MT7621AT

fix in sdhci Use ralink_soc == MT762X_SOC_MT7621AT instead of CONFIG_SOC_MT7621 which is
wrong and breaks builds on mt7620a-similar platforms (MT7621, MT7688)

Signed-off-by: Andrew Yong <me@ndoo.sg>
2 years agolantiq: add missing metadata for tp-link images
Felix Fietkau [Mon, 21 Nov 2016 15:13:23 +0000 (16:13 +0100)]
lantiq: add missing metadata for tp-link images

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoscripts/getver.sh: treat all commits as local if can't find upstream
Rafał Miłecki [Thu, 17 Nov 2016 06:25:21 +0000 (07:25 +0100)]
scripts/getver.sh: treat all commits as local if can't find upstream

If something goes wrong and script can't find upstream revision it will
return something like:
r2220
which looks like a valid upstream revision 2220. We cant' distinguish it
from e.g. 2200 upstream commits and 20 local ones.

The new format still provides revision number but also points clearly
that is may be not the upstream one:
r0+2220

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: John Crispin < john@phrozen.org>
2 years agogrub2: add PKG_FIXUP:=autoreconf
Alexandru Ardelean [Thu, 17 Nov 2016 16:25:52 +0000 (18:25 +0200)]
grub2: add PKG_FIXUP:=autoreconf

The host-side build of grub2 requires this sometimes.
This will re-generate the ./configure script from configure.ac.
I don't know the conditions of how this reproduces, it just
sometimes appears, and sometimes doesn't.

Build error
```
<lede-dir>/build_dir/target-x86_64_musl-1.1.15_yogi/host/grub-2.02~beta2/build-aux/missing: line 81: aclocal-1.14: command not found
WARNING: 'aclocal-1.14' is missing on your system.
         You should only need it if you modified 'acinclude.m4' or
         'configure.ac' or m4 files included by 'configure.ac'.
         The 'aclocal' program is part of the GNU Automake package:
         <http://www.gnu.org/software/automake>
         It also requires GNU Autoconf, GNU m4 and Perl in order to run:
         <http://www.gnu.org/software/autoconf>
         <http://www.gnu.org/software/m4/>
         <http://www.perl.org/>
Makefile:3962: recipe for target 'aclocal.m4' failed
```

Adding PKG_FIXUP adds sanity (i.e. autoreconf is used for host & target
builds) over just using HOST_FIXUP.

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
2 years agoramips: Fix sdhci kernel panics on MT7621
Andrew Yong [Mon, 21 Nov 2016 07:14:16 +0000 (15:14 +0800)]
ramips: Fix sdhci kernel panics on MT7621

Enable work-arounds present in the code commented-out but needed to write to
sdcard on mt7621 which currently causes kernel to oops when engaging in
serious writing to sdcard. With this change applied, there are still
occasional warnings thrown by the mmc driver, however, at least it no longer
crashes the system and even large writes (full-card dump/erase/write/compare)
don't show any corruption.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rebase to LEDE and added "CONFIG_SOC_MT7621" check to ensure non-MT7621 devices do not face performance regressions.
Signed-off-by: Andrew Yong <me@ndoo.sg>
2 years agoodhcpd: update to latest git HEAD
John Crispin [Mon, 21 Nov 2016 11:16:55 +0000 (12:16 +0100)]
odhcpd: update to latest git HEAD

Signed-off-by: John Crispin <john@phrozen.org>
2 years agoodhcpd: update to latest git HEAD
John Crispin [Mon, 21 Nov 2016 11:04:23 +0000 (12:04 +0100)]
odhcpd: update to latest git HEAD

Signed-off-by: John Crispin <john@phrozen.org>
2 years agomvebu: Add BQL patch for mvneta driver.
Toke Høiland-Jørgensen [Mon, 21 Nov 2016 10:12:09 +0000 (11:12 +0100)]
mvebu: Add BQL patch for mvneta driver.

This adds the patch submitted to upstream that adds BQL to the mvneta
driver: https://patchwork.kernel.org/patch/9328413/. Helps latency under
load when the physical link is saturated.

Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
2 years agofirmware-utils: Add support for the Cisco Meraki MX60/MX60W
Chris Blake [Wed, 16 Nov 2016 14:35:54 +0000 (08:35 -0600)]
firmware-utils: Add support for the Cisco Meraki MX60/MX60W

This patch adds header support for the Cisco Meraki MX60/MX60W, which
are a part of the apm821xx target. Some structure changes were needed
due to the fact this device uses U-Boot (unlike other devices in
mkmerakifw.c) which uses a different header structure to define the load
offsets for the image.

A thanks to Christian for helping implement this properly.

Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2 years agolantiq: use dwc2 by default on danube
Ben Mulvihill [Tue, 8 Nov 2016 21:03:26 +0000 (22:03 +0100)]
lantiq: use dwc2 by default on danube

Use dwc2 by default on all danube boards.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
2 years agolantiq: dwc2 parameters for danube
Ben Mulvihill [Tue, 8 Nov 2016 21:03:14 +0000 (22:03 +0100)]
lantiq: dwc2 parameters for danube

Parameters for dwc2 on lantiq.

A separate dwc2_core_params structure is defined for danube because danube
fifo sizes are large enough to be autodetected. This is not the case on
arx and vrx.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
2 years agolantiq: device tree bindings for dwc2 on danube
Ben Mulvihill [Tue, 8 Nov 2016 21:03:03 +0000 (22:03 +0100)]
lantiq: device tree bindings for dwc2 on danube

Device tree binding for dwc2 usb driver on danube.
Leave old ifxhcd-danube driver as an alternative.

Also adds dr_mode = "host" to eliminate warning on boot.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
2 years agolantiq: initialise dwc2 on danube
Ben Mulvihill [Tue, 8 Nov 2016 21:02:42 +0000 (22:02 +0100)]
lantiq: initialise dwc2 on danube

Initialise dwc2 usb driver on danube boards as well as ar9 and vr9.

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
2 years agoapm821xx: Add support for the Cisco Meraki MX60/MX60W
Chris Blake [Wed, 16 Nov 2016 15:38:07 +0000 (09:38 -0600)]
apm821xx: Add support for the Cisco Meraki MX60/MX60W

This patch adds support for the Cisco Meraki MX60/MX60W Security
Appliance. Flashing information can be found at
https://github.com/riptidewave93/LEDE-MX60

Specs are as follows:
AppliedMicro APM82181 SoC at 800MHz
1GiB NAND - Samsung K9K8G08U0D
512MB DDR RAM - 4x Nanya NT5TU128M8GE-AC
Atheros AR8327-BL1A Gigabit Ethernet Switch
1x USB 2.0 Port

More info can be found at https://wiki.openwrt.org/toh/meraki/mx60

Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2 years agoramips: add support for WeVO W2914NS v2
perillamint [Fri, 18 Nov 2016 11:46:27 +0000 (20:46 +0900)]
ramips: add support for WeVO W2914NS v2

Signed-off-by: Yong-hyu Ban <perillamint@gentoo.moe>