openwrt/openwrt.git
2 years agoar71xx: move Wallys DR344 to generic build target
Piotr Dymacz [Mon, 29 May 2017 20:07:04 +0000 (22:07 +0200)]
ar71xx: move Wallys DR344 to generic build target

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agoar71xx: fix Wallys DR344 GPIO-connected LEDs and button
Piotr Dymacz [Mon, 29 May 2017 19:32:11 +0000 (21:32 +0200)]
ar71xx: fix Wallys DR344 GPIO-connected LEDs and button

This fixes wrong GPIO numbers for LEDs and button in Wallys DR344 board
and sets color of all LEDs to green as the mass production boards have
only green one.

Actually, DR344 has 6 GPIO-connected LEDs and one button:

- GPIO11: status
- GPIO12: sig1
- GPIO13: sig2
- GPIO14: sig3
- GPIO15: sig4
- GPIO16: reset button
- GPIO17: lan

WAN LED is connected directly with AR8035 PHY.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agoar71xx: set GE interface as wan by default in Wallys DR344
Piotr Dymacz [Mon, 29 May 2017 19:25:03 +0000 (21:25 +0200)]
ar71xx: set GE interface as wan by default in Wallys DR344

This aligns default network interfaces configuration with vendor
firmware: GE (eth0) -> wan, FE (eth1) -> lan.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agoar71xx: fix GE interface support in Wallys DR344
Piotr Dymacz [Mon, 29 May 2017 17:18:52 +0000 (19:18 +0200)]
ar71xx: fix GE interface support in Wallys DR344

GMAC0 interface of AR9344 SOC in Wallys DR344 board is connected with
AR8035, not with AR8327. Without this fix, GE interface doesn't work at
all or shows high packet loss ratio.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agoar71xx: add support for EnGenius ENS202EXT
Marty Plummer [Fri, 14 Apr 2017 17:08:17 +0000 (12:08 -0500)]
ar71xx: add support for EnGenius ENS202EXT

EnGenius ENS202EXT is an outdoor wireless access point with
2-port 10/100 switch, detachable antennas and proprietery PoE.

The device is based on Qualcomm/Atheros AR9341 v1.

Specifications:
- 535/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM
- 16 MB of FLASH
- UART (J1) header on PCB (unpopulated)
- 2x 10/100 Mbps Ethernet
- 2.4 GHz, up to 26dBm
- 2x external, detachable antennas
- 7x LED, 1x button

Flash instructions:

You have three options:

- Use the vendor firmware upgrade page on the web interface and give
it the factory.img. This is the easiest way to go about it.

- If you have serial access during u-boot, interrupt the normal boot
(any key before timeout) and run 'run failsafe_boot'; this will bring
you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've
bricked the normal firmware.

- Use the vendor's management cli, which can be accessed via telnet
with the same credentials as the web login (default admin:admin), then
issue the following commands:

*** Hi admin, welcome to use cli(V-1.6.7) ***
---========= Commands Help =========---
      stat -- Status
       sys -- System
    wless2 -- 2.4G-Wireless
      mgmt -- Management
      tree -- Tree
      help -- Help
    reboot -- Reboot
ens202ext>mgmt
  Management
---========= Commands Help =========---
     admin -- Administration
     mvlan -- Management VLAN settings
      snmp -- SNMP settings
    backup -- Backup/Restore settings
    autorb -- Auto reboot settings
   fwgrade -- Firmware upgrade
      time -- Time settings
   wifisch -- Wifi schedule
       log -- Log
      diag -- Diagnostics
      disc -- Device Discovery
    logout -- Logout
      help -- Help
      exit -- Exit
ens202ext/mgmt>fwgrade
  Management --> Firmware upgrade
---========= Commands Help =========---
      fwup -- Firmware upgrade
      help -- Help
      exit -- Exit
ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin

Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
2 years agoar71xx: fix LED defines for TP-Link TL-WR740N v6
Andrey Polischuk [Thu, 11 May 2017 18:26:21 +0000 (21:26 +0300)]
ar71xx: fix LED defines for TP-Link TL-WR740N v6

Signed-off-by: Andrey Polischuk <androld.b@gmail.com>
[changed commit subject, dropped redundant kernel config symbol]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agoiproute2: bump to 4.11
Kevin Darbyshire-Bryant [Mon, 20 Mar 2017 21:53:46 +0000 (21:53 +0000)]
iproute2: bump to 4.11

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
2 years agotoolchain/binutils: Set 2.28 as default version
Daniel Engberg [Sun, 14 May 2017 11:47:45 +0000 (13:47 +0200)]
toolchain/binutils: Set 2.28 as default version

Use 2.28 by default

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2 years agomvebu: clearfog: assign SFP port to WAN zone
Josua Mayer [Mon, 22 May 2017 17:07:13 +0000 (19:07 +0200)]
mvebu: clearfog: assign SFP port to WAN zone

The single SFP port is meant for direct media access to WAN, such as
VDSL2, GPON). While it could also be used for in-home fiber, it is much
more likely that the LAN is standard ethernet, especially considering
that SFP is the onmly port that can go beyond 1Gbps.

Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
2 years agomvebu: clearfog: document interface configuration
Josua Mayer [Mon, 24 Apr 2017 14:52:31 +0000 (16:52 +0200)]
mvebu: clearfog: document interface configuration

Take explicit note of what physical ports eth{0,1,2} refer to.
Also repair port assignment:
At some point between 4.9.20 and 4.9.29 the numbering changed.
Keep previous port assignment that was:
LAN = SFP+Switch
WAN = standalone ethernet

Also use the same assignment for Clearfog-Base to avoid confusion.

Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
2 years agomvebu: clearfog: include DTB for all variants in image
Josua Mayer [Mon, 22 May 2017 15:04:19 +0000 (17:04 +0200)]
mvebu: clearfog: include DTB for all variants in image

Installing all armada-388-clearfog-* DTBs in the same sdcard image,
it now becomes much easier to swap sdcards between different device variants.

Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
2 years agomvebu: update boot-script to use generic variables
Josua Mayer [Sun, 23 Apr 2017 15:20:58 +0000 (17:20 +0200)]
mvebu: update boot-script to use generic variables

U-Boot provides standard variables for load addresses, and
filesystem-agnostic load-commands. Furthermore thanks to distro-boot,
the device and partition from which the system boots is known.
The new boot-script makes use of all this information.

Tested on the only board that uses this boot-script: Clearfog Pro

Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
2 years agou-boot-mvebu: clearfog: enable setexpr command
Josua Mayer [Sun, 23 Apr 2017 18:28:57 +0000 (20:28 +0200)]
u-boot-mvebu: clearfog: enable setexpr command

Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
2 years agou-boot-mvebu: clearfog: implement distro-boot
Josua Mayer [Sun, 23 Apr 2017 17:22:32 +0000 (19:22 +0200)]
u-boot-mvebu: clearfog: implement distro-boot

Add a patchfile that implements distro-boot and is meant to go upstream
Also make the other patches git-am'able for easier maintenance.

Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
2 years agou-boot-mvebu: update to 2017.03
Josua Mayer [Sun, 23 Apr 2017 16:19:59 +0000 (18:19 +0200)]
u-boot-mvebu: update to 2017.03

Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
2 years agomwlwifi: update to the latest version
Ansuel Smith [Fri, 21 Apr 2017 13:08:42 +0000 (15:08 +0200)]
mwlwifi: update to the latest version

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2 years agotoolchain/gcc: fix --with-isl path
Syrone Wong [Tue, 30 May 2017 07:10:02 +0000 (15:10 +0800)]
toolchain/gcc: fix --with-isl path

This fixes GCC 7 compilation when GRAPHITE is selected.
The path is replaced with $(TOOLCHAIN_DIR), while it should be
$(STAGING_DIR_HOST). To keep in sync with the path of gmp,
mpfr and mpc, I'm using $(TOPDIR)/staging_dir/host.

Fixes: f62f4b3c5c9d ("build: stop overriding STAGING_DIR_HOST for toolchain build")

Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
2 years agomt76: update to the latest version, fixes a mt7603 beacon issue
Felix Fietkau [Tue, 30 May 2017 06:47:16 +0000 (08:47 +0200)]
mt76: update to the latest version, fixes a mt7603 beacon issue

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoprocd: update to latest git HEAD
Matthias Schiffer [Tue, 30 May 2017 05:29:25 +0000 (07:29 +0200)]
procd: update to latest git HEAD

e7bb2c8 upgraded: define __GNU_SOURCE

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agosunxi: sysupgrade: sync with x86
Matthias Schiffer [Thu, 4 May 2017 05:39:20 +0000 (07:39 +0200)]
sunxi: sysupgrade: sync with x86

sunxi sysupgrade was based on the x86 implementation; sync fixes and other
changes from the current x86 version:

x86: fix sysupgrades on disks with 4k block size
x86: sysupgrade: move partition table change check to platform_check_image
x86: sysupgrade: refactor platform_do_upgrade
x86: sysupgrade: explicitly rescan disk after writing partition table

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agosunxi: sysupgrade: don't write partitions twice
Matthias Schiffer [Thu, 4 May 2017 05:29:58 +0000 (07:29 +0200)]
sunxi: sysupgrade: don't write partitions twice

When existing partitions are retained, the dd call writing the uboot image
in the space before the first partition was accidentally writing the whole
image, making the code for individual partitions redundant. Limit the copy
to 1016KiB (the first 8KiB are skipped, and the first partition starts at
1024KiB).

In addition, conv=notrunc is replaced with conv=fsync. It seems this was an
oversight, as notrunc doesn't make sense for block devices and all other dd
commands use conv=fsync.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agox86: sysupgrade: explicitly rescan disk after writing partition table
Matthias Schiffer [Wed, 3 May 2017 07:08:29 +0000 (09:08 +0200)]
x86: sysupgrade: explicitly rescan disk after writing partition table

This should ensure that the kernel partition can be mounted in
platform_copy_config when its size has changed.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agox86: sysupgrade: refactor platform_do_upgrade
Matthias Schiffer [Wed, 3 May 2017 07:05:25 +0000 (09:05 +0200)]
x86: sysupgrade: refactor platform_do_upgrade

By returning early when no upgrade device can be found and handling the
SAVE_PARTITIONS=0 case differently, we can get rid of two levels of if.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agox86: sysupgrade: move partition table change check to platform_check_image
Matthias Schiffer [Wed, 3 May 2017 06:57:29 +0000 (08:57 +0200)]
x86: sysupgrade: move partition table change check to platform_check_image

The staged sysupgrade will prevent us from using ask_bool in
platform_do_upgrade; therefore, the check is moved to platform_check_image.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agoramips: sysupgrade: move nand_do_upgrade call to platform_do_upgrade
Matthias Schiffer [Sat, 22 Apr 2017 19:27:04 +0000 (21:27 +0200)]
ramips: sysupgrade: move nand_do_upgrade call to platform_do_upgrade

All targets with NAND support should gradually move their nand_do_upgrade
calls from platform_pre_upgrade to platform_do_upgrade.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agobase-files: add support for staged sysupgrades from failsafe mode
Matthias Schiffer [Sun, 23 Apr 2017 23:31:04 +0000 (01:31 +0200)]
base-files: add support for staged sysupgrades from failsafe mode

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agobase-files: sysupgrade cleanup
Matthias Schiffer [Sun, 23 Apr 2017 21:33:14 +0000 (23:33 +0200)]
base-files: sysupgrade cleanup

Some functions only used by stage2 are moved there from common.sh.

One piece that could still use more cleanup is platform_pre_upgrade: many
targets reference files from there are aren't available in the ramfs, so
we need to evaluate it before the switch; conversely, flash writes happen
in that function on some targets. Targets that do the latter should be
fixed eventually to use platform_do_upgrade for that purpose.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agofstools: snapshot: handle jffs2 conversion using upgraded
Matthias Schiffer [Wed, 3 May 2017 06:29:55 +0000 (08:29 +0200)]
fstools: snapshot: handle jffs2 conversion using upgraded

We can reuse the kill_remaining and run_ramfs facilities of the stage2 run
by upgraded.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agofstools: clean up trailing whitespace in snapshot script
Matthias Schiffer [Wed, 3 May 2017 06:29:24 +0000 (08:29 +0200)]
fstools: clean up trailing whitespace in snapshot script

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agobase-files: always use staged sysupgrade
Matthias Schiffer [Fri, 21 Apr 2017 22:54:50 +0000 (00:54 +0200)]
base-files: always use staged sysupgrade

Support for the -d and -p options is dropped; it may be added again at some
point by adding these flags to the ubus sysupgrade call.

A downside of this is that we get a lot less information about the progress
of the upgrade: as soon as the actual upgrade starts, all shell sessions
are killed to allow unmounting the root filesystem.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agoprocd: remove procd-nand package
Matthias Schiffer [Fri, 21 Apr 2017 18:37:58 +0000 (20:37 +0200)]
procd: remove procd-nand package

We always want to support staged upgrades now, so it's better to include
upgraded into the main package. /lib/upgrade/nand.sh is moved to
base-files.

The procd-nand-firstboot package is removed for now, it may return later
as a separate package.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agoprocd: update to latest git HEAD
Matthias Schiffer [Mon, 29 May 2017 21:15:22 +0000 (23:15 +0200)]
procd: update to latest git HEAD

992b796 rcS: add missing fcntl.h include
63789e5 init: add support for sysupgrades triggered from preinit
5b1fb35 Remove code that has become unnecessary after sysupgrade changes
5918b6d upgraded: add support for passing a "command" argument to stage2
056d8dd upgraded: link dynamically, chroot during exec
7c6cf55 system: always support staged sysupgrade
d42b21e procd/rcS: Use /dev/null as stdin
e0098d4 service/instance: add an auto start option
1247db1 procd: Log initscript output prefixed with script name
8d720b2 procd: Don't use syslog before its initialization
2555474 procd: Add missing \n in debug message

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agoprocd: prepare NAND sysupgrade for making upgraded dynamically linked
Matthias Schiffer [Wed, 3 May 2017 06:28:05 +0000 (08:28 +0200)]
procd: prepare NAND sysupgrade for making upgraded dynamically linked

Use install_bin to copy upgraded with all dependencies. The old name
/tmp/upgraded is temporarily retained as a symlink to avoid breaking
things.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agoprocd: clean up trailing whitespace in nand.sh
Matthias Schiffer [Wed, 3 May 2017 06:27:40 +0000 (08:27 +0200)]
procd: clean up trailing whitespace in nand.sh

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2 years agomt76: update to the latest version, improves mt7603/7628 stability
Felix Fietkau [Mon, 29 May 2017 12:42:16 +0000 (14:42 +0200)]
mt76: update to the latest version, improves mt7603/7628 stability

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agobuild: fix kmod package build on non-GNU systems
Felix Fietkau [Mon, 29 May 2017 12:26:36 +0000 (14:26 +0200)]
build: fix kmod package build on non-GNU systems

BSD paste requires a filename argument, and it accepts - to use stdin as
intended.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agotools/sparse: Update to snapshot 2017-03-31
Daniel Engberg [Wed, 10 May 2017 09:34:10 +0000 (11:34 +0200)]
tools/sparse: Update to snapshot 2017-03-31

Update sparse to snapshot 2017-03-31
Switch to HTTPS

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2 years agotoolchain/insight: Remove from tree
Daniel Engberg [Mon, 29 May 2017 07:41:15 +0000 (09:41 +0200)]
toolchain/insight: Remove from tree

Insight hasn't been touched since 2009 and I can't find any references at
least 6 years back of being used. Ubuntu and Debian removed insight years ago
from their repos so I think we can safely remove this too.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2 years agolantiq: pinctrl: xway: fix copy/paste error in xrx200_grps
Martin Schiller [Mon, 29 May 2017 04:17:07 +0000 (06:17 +0200)]
lantiq: pinctrl: xway: fix copy/paste error in xrx200_grps

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2 years agoipq806x: add qpic nand and bam dma node's in ipq4019 dts tree
Ram Chandra Jangir [Wed, 24 May 2017 23:31:03 +0000 (05:01 +0530)]
ipq806x: add qpic nand and bam dma node's in ipq4019 dts tree

This change adds QPIC BAM dma and NAND driver node's in IPQ4019
device tree, also enable this for AP-DK04.1 based boards.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2 years agoipq806x: Add support for custom data mapping in bam_dma dmaengine
Ram Chandra Jangir [Wed, 24 May 2017 23:31:02 +0000 (05:01 +0530)]
ipq806x: Add support for custom data mapping in bam_dma dmaengine

This change adds a new function to support for preparing DMA descriptor
for custom data.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2 years agoipq806x: Added bam transaction and support additional CSRs
Ram Chandra Jangir [Wed, 24 May 2017 23:31:01 +0000 (05:01 +0530)]
ipq806x: Added bam transaction and support additional CSRs

This change adds support for below:
- Bam transaction which will be used for any NAND request.
- Reset function for NAND BAM transaction
- Add support for additional CSRs.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2 years agoipq806x: Add bam_dma support in qcom_nand driver
Ram Chandra Jangir [Wed, 24 May 2017 23:31:00 +0000 (05:01 +0530)]
ipq806x: Add bam_dma support in qcom_nand driver

The existing qcom_nand driver supports ADM DMA which is mainly
required for ipq806x family based boards,
IPQ40xx based boards uses BAM DMA in NAND driver, so this patch
adds BAM DMA support with compatible string as qcom,ebi2-nandc-bam.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2 years agoipq806x: Add support to configure ipq40xx GPIO_PULL bits
Ram Chandra Jangir [Wed, 24 May 2017 23:30:59 +0000 (05:00 +0530)]
ipq806x: Add support to configure ipq40xx GPIO_PULL bits

GPIO_PULL bits configurations in TLMM_GPIO_CFG register
differs for IPQ40xx from rest of the other qcom SoC's.
This change add support to configure the msm_gpio_pull
bits for ipq40xx, It is required to fix the proper
configurations of gpio-pull bits for nand pins mux.

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2 years agofirewall: fix stray continue statement
Jo-Philipp Wich [Sat, 27 May 2017 14:14:10 +0000 (16:14 +0200)]
firewall: fix stray continue statement

The previous commit introduced a faulty continue statement which might
lead to faulty rules not getting freed or reported.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2 years agonetifd: fix 6rd regression (FS#812)
Hans Dedecker [Sat, 27 May 2017 11:18:33 +0000 (13:18 +0200)]
netifd: fix 6rd regression (FS#812)

08f1875 system-linux: fix 6rd regression

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2 years agofirewall: extend ubus support, exception handling, parse fixes
Jo-Philipp Wich [Sun, 14 May 2017 19:00:26 +0000 (21:00 +0200)]
firewall: extend ubus support, exception handling, parse fixes

Update to latest Git HEAD in order to import a number of fixes and other
improvements:

3d2c18a options: improve handling of negations when parsing space separated values
0e5dd73 iptables: support -i, -o, -s and -d in option extra
4cb06c7 ubus: increase ubus network interface dump timeout
e5dfc82 iptables: add exception handling
f625954 firewall3: add check_snat() function
7d3d9dc firewall3: display the section type for UBUS rules
53ef9f1 firewall3: add UBUS support for include scripts
5cd4af4 firewall3: add UBUS support for ipset sections
02d6832 firewall3: add UBUS support for forwarding sections
0a7d36d firewall3: add UBUS support for redirect sections
d44f418 firewall3: add fw3_attr_parse_name_type() function
e264c8e firewall3: replace warn_rule() by warn_section()
6039c7f firewall3: check the return value of fw3_parse_options()

Fixes FS#548, FS#806, FS#811.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2 years agobrcm47xx: remove target specific network preinit config
Jo-Philipp Wich [Wed, 17 May 2017 12:36:23 +0000 (14:36 +0200)]
brcm47xx: remove target specific network preinit config

The generic preinit code is now able to setup network and switch vlan settings
from the /etc/board.json file, therefor drop the target specific code.

Fixes FS#790.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2 years agosamba: bump PKG_RELEASE
Jo-Philipp Wich [Sat, 27 May 2017 10:15:06 +0000 (12:15 +0200)]
samba: bump PKG_RELEASE

The previous CVE bugfix commit did not adjust PKG_RELEASE, therefor the
fixed samba package does not appear as opkg update.

Bump the PKG_RELEASE to signify upgrades to downstream users.

Ref: https://forum.lede-project.org/t/sambacry-are-lede-devices-affected/3972/4

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2 years agox86: fix build of geode target
Hauke Mehrtens [Sat, 27 May 2017 09:29:55 +0000 (11:29 +0200)]
x86: fix build of geode target

The build bot complained that the OLPC option was not set.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agokernel: add missing config options
Hauke Mehrtens [Sat, 27 May 2017 09:29:28 +0000 (11:29 +0200)]
kernel: add missing config options

This broke the build for the x86 generic target.
This was found by the build bot.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agoMove enablemodem from ramips to new package adb-enablemodem and make it used also...
Filip Moc [Thu, 25 May 2017 19:55:32 +0000 (21:55 +0200)]
Move enablemodem from ramips to new package adb-enablemodem and make it used also by TL-MR6400

Signed-off-by: Filip Moc <lede@moc6.cz>
2 years agoar71xx: Add support for TP-Link MR6400
Filip Moc [Thu, 25 May 2017 19:51:37 +0000 (21:51 +0200)]
ar71xx: Add support for TP-Link MR6400

You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin
on 192.168.0.66/24, connect to any ethernet port and power on device while
holding the reset button). Flashing via OEM web interface does not work.

Hardware Specification (v1.0 EU):
 - SoC: QCA9531
 - Flash: Winbond W25Q64FV (8MiB)
 - RAM: EtronTech EM6AB160TSE-5G (64MiB)
 - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna)
 - Ethernet: 2NIC (3x100M + 1x100M)
 - WWAN: TP-LINK LTE MODULE (2x external detachable antenna)
 - Power: DC 12V 1A

Signed-off-by: Filip Moc <lede@moc6.cz>
2 years agoramips: remove fictional LEDs from AsiaRF AWM00x device tree
Russell Senior [Wed, 24 May 2017 17:22:05 +0000 (10:22 -0700)]
ramips: remove fictional LEDs from AsiaRF AWM00x device tree

Neither the AsiaRF AWM002 or AWM003 actually has an LED on the module
board.  The ld1 and ld2 do not represent actual LEDs.  These pins might
connect to LEDS on an eval board or other carrier board, but that is
outside the scope of this device tree file.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2 years agousbmode: update usb-modeswitch-data to 20170205
Julian Labus [Wed, 24 May 2017 14:32:17 +0000 (16:32 +0200)]
usbmode: update usb-modeswitch-data to 20170205

add support for new hardware

Signed-off-by: Julian Labus <julian@labus-online.de>
2 years agousbmode: update to latest version
Julian Labus [Wed, 24 May 2017 14:32:16 +0000 (16:32 +0200)]
usbmode: update to latest version

453da8e convert-modeswitch.pl: fix message indices

Signed-off-by: Julian Labus <julian@labus-online.de>
2 years agobuild: fix possible issue with kmod package having multiple AutoLoad's
Yousong Zhou [Sat, 27 May 2017 02:22:02 +0000 (10:22 +0800)]
build: fix possible issue with kmod package having multiple AutoLoad's

This commit contains the following changes

 - Use local shell var where appliable
 - The $(sort $$$$$$$$mods) call will have no expected effect
 - Avoid EEXIST when creating symlinks in /etc/modules-boot.d/
 - Avoid duplicate arguments for insert_modules() in postinst-pkg

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2 years agokernel: update kernel 4.4 to 4.4.70
Hauke Mehrtens [Fri, 26 May 2017 21:38:19 +0000 (23:38 +0200)]
kernel: update kernel 4.4 to 4.4.70

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agokernel: update kernel 4.9 to 4.9.30
Hauke Mehrtens [Fri, 26 May 2017 20:56:32 +0000 (22:56 +0200)]
kernel: update kernel 4.9 to 4.9.30

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 years agouml: Fix sample command line
Florian Fainelli [Tue, 23 May 2017 03:21:55 +0000 (20:21 -0700)]
uml: Fix sample command line

Provide paths that match where LEDE is staging images.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2 years agouml: Check for glibc static libraries
Florian Fainelli [Tue, 23 May 2017 02:35:00 +0000 (19:35 -0700)]
uml: Check for glibc static libraries

UML statically links against libutil, librt and libpthread. Some hosts do not
necessarily have these libraries installed and we should find out sooner than
later (during the final vmlinux linking stage) about that.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2 years agokernel: Make KERNEL_PERF_EVENTS selectable
Florian Fainelli [Mon, 22 May 2017 23:46:46 +0000 (16:46 -0700)]
kernel: Make KERNEL_PERF_EVENTS selectable

The kernel itself allows enabling/disabling CONFIG_PERF_EVENTS, so allow
doing the same thing.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2 years agokernel: Hide kernel options behind a menu
Florian Fainelli [Mon, 22 May 2017 23:45:52 +0000 (16:45 -0700)]
kernel: Hide kernel options behind a menu

We are starting to add more and more kernel configurable options, to the
point where the Global build options menu is not really usable anymore,
hide all kernel-related configuration options behind a menu.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2 years agoelfutils: Pass -Wno-unused-result to silence warnings as errors
Florian Fainelli [Mon, 22 May 2017 23:08:57 +0000 (16:08 -0700)]
elfutils: Pass -Wno-unused-result to silence warnings as errors

elfutils turns on -Werror by default, and patch 100-musl-compat.patch
changes how strerror_r is used and we no longer use the function's
return value. This causes the following build error/warning to occur
with glibc-based toolchains:

dwfl_error.c: In function 'dwfl_errmsg':
dwfl_error.c:158:18: error: ignoring return value of 'strerror_r',
declared with attribute warn_unused_result [-Werror=unused-result]
       strerror_r (error & 0xffff, s, sizeof(s));
                  ^
cc1: all warnings being treated as errors

Fixing this would be tricky as there are two possible signatures for
strerror_r (XSI and GNU), just turn off unused-result warnings instead.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2 years agodnsmasq: add dhcp-script hook for other packages
Nick Brassel [Sat, 6 May 2017 10:56:26 +0000 (20:56 +1000)]
dnsmasq: add dhcp-script hook for other packages

Adds a script which acts as a hook for when dnsmasq creates/destroys a
lease, or completes a TFTP file transfer. The hook loops through scripts
in appropriate directories inside '/etc/hotplug.d', executing each one with
the same arguments supplied by dnsmasq.

In case dnsmasq is jailed by ujail the dhcp-script hook will not work as
expected as ujail does not yet support executing a script within a jail.

Signed-off-by: Nick Brassel <nick@tzarc.org>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2 years agotreewide: fix device tree path in scripts
Mathias Kresin [Fri, 26 May 2017 13:13:42 +0000 (15:13 +0200)]
treewide: fix device tree path in scripts

The device tree is at /proc/device-tree/ without a base subdir.

Fixes: da472e5b30f6 ("treewide: access device tree from userspace via /proc/")

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agoRevert "sysupgrade: run only one instance at a time."
Jo-Philipp Wich [Fri, 26 May 2017 12:48:05 +0000 (14:48 +0200)]
Revert "sysupgrade: run only one instance at a time."

This reverts commit e96a9a9af82c00dcce606a84a7bb87a00411385d.

The change breaks sysupgrade through LuCI and two-stage sysupgrade on
NAND targets. There is also a mismatch of file paths in lock and unlock
operations.

This commit was apparently neither properly tested, nor reviewed, so
drop it for now.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2 years agoramips: add support for GL-inet GL-MT300N-V2
Kyson Lok [Wed, 17 May 2017 10:18:45 +0000 (18:18 +0800)]
ramips: add support for GL-inet GL-MT300N-V2

This patch adds supports for the GL-inet GL-MT300N-V2.

Specification:
- SoC: MediaTek MT7628AN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR
- Ethernet: 1 x WAN (100 Mbps) and 1 x LAN (100 Mbps)
- USB: 1 x USB 2.0 port
- Button: 1 x switch button, 1 x reset button
- LED: 3 x LEDS (system power led is not GPIO controller)
- UART: 1 x UART on PCB (JP1: 3.3V, RX, TX, GND)

Installation through Luci:
- The original firmware is LEDE, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.

Installation through bootloader webserver:
- Plug power and hold reset button until red LED blink to bright.
- Install sysupgrade image using web interface on 192.168.1.1.

Signed-off-by: Kyson Lok <kysonlok@gmail.com>
[match maximum image size with firmware partition]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agotreewide: access device tree from userspace via /proc/
Mathias Kresin [Wed, 10 May 2017 08:44:18 +0000 (10:44 +0200)]
treewide: access device tree from userspace via /proc/

Access the device tree via /proc/device-tree/ is the documented way to
access the properties. Everything else might not work in future.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2 years agoflex: update to 2.6.4 (FS#809)
Eric Luehrsen [Fri, 26 May 2017 04:02:47 +0000 (00:02 -0400)]
flex: update to 2.6.4 (FS#809)

flex 2.6.3 has a bug which fails code generation and compile of some packages

Signed-off-by: Eric Luehrsen <ericluehrsen@hotmail.com>
2 years agox86/legacy: disable PAE again
Daniel Golle [Thu, 25 May 2017 21:44:23 +0000 (23:44 +0200)]
x86/legacy: disable PAE again

commit 961c0eacea ('x86: fix lifting kernel CPU requirements and always
enable PAE') broke some older geode boards such as Soekris net4826.
Hence disable PAE on x86/legacy again in order to still support those
very old non-PAE capable CPUs.

Fixes FS#773 - PAE broke Soekris net4826

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agobuild: fix QUILT related overrides
Felix Fietkau [Thu, 25 May 2017 18:38:10 +0000 (20:38 +0200)]
build: fix QUILT related overrides

They need to be defined before including quilt.mk

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoiptables: fix typos in 600-shared-libext.patch (FS#711)
Felix Fietkau [Thu, 25 May 2017 17:30:06 +0000 (19:30 +0200)]
iptables: fix typos in 600-shared-libext.patch (FS#711)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoDWR-512: adding wwan support for the dwr-512 3G modem
Giuseppe Lippolis [Thu, 22 Dec 2016 21:12:44 +0000 (22:12 +0100)]
DWR-512: adding wwan support for the dwr-512 3G modem

This PR allow the 3G modem embedded in the DWR-512 to be managed
by the wwan-ncm scripts. The modem will use the usb-option and
usb-cdc-ether drivers.
The DWR-512 DT is updated accordingly.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2 years agogcc: fix documentation entries added by 910-mbsd_multi.patch
Felix Fietkau [Wed, 10 May 2017 12:01:54 +0000 (14:01 +0200)]
gcc: fix documentation entries added by 910-mbsd_multi.patch

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoscripts/download.pl: print the command used to download files
Felix Fietkau [Tue, 9 May 2017 13:20:42 +0000 (15:20 +0200)]
scripts/download.pl: print the command used to download files

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agoxfsprogs: update to 4.11.0
Felix Fietkau [Tue, 9 May 2017 13:20:23 +0000 (15:20 +0200)]
xfsprogs: update to 4.11.0

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agotools/libressl: update to 2.5.4
Hannu Nyman [Sun, 7 May 2017 17:52:32 +0000 (20:52 +0300)]
tools/libressl: update to 2.5.4

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2 years agotools/flex: update to 2.6.3
Hannu Nyman [Fri, 28 Apr 2017 13:53:42 +0000 (16:53 +0300)]
tools/flex: update to 2.6.3

* update flex to 2.6.3
* download .tar.gz (as upstream has dropped .xz)
* refresh patches

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2 years agotools/cmake: update to 3.8.1
Hannu Nyman [Mon, 8 May 2017 19:18:25 +0000 (22:18 +0300)]
tools/cmake: update to 3.8.1

* update cmake to 3.8.1
* refresh patches

Release notes:
https://cmake.org/cmake/help/v3.8/release/3.8.html

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2 years agox86_64: add drivers for Xeon controller hub based GPIO
Philip Prindeville [Tue, 28 Mar 2017 00:25:24 +0000 (18:25 -0600)]
x86_64: add drivers for Xeon controller hub based GPIO

These drivers are in many reference-design Xeon, iCore, or
Atom64 based server boards.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
2 years agojson-c: disable implicit fallthrough warning (gcc 7)
Felix Fietkau [Thu, 4 May 2017 13:45:35 +0000 (15:45 +0200)]
json-c: disable implicit fallthrough warning (gcc 7)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agofirewall: update to the latest version, fixes a gcc7 build error
Felix Fietkau [Thu, 4 May 2017 14:11:27 +0000 (16:11 +0200)]
firewall: update to the latest version, fixes a gcc7 build error

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agotoolchain: add gcc 7.1.0 support
Felix Fietkau [Thu, 4 May 2017 13:18:13 +0000 (15:18 +0200)]
toolchain: add gcc 7.1.0 support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agotools/isl: update to 0.18
Syrone Wong [Sun, 7 May 2017 11:39:12 +0000 (19:39 +0800)]
tools/isl: update to 0.18

Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
2 years agoocteon: remove linux 4.4 support
Felix Fietkau [Thu, 4 May 2017 10:57:47 +0000 (12:57 +0200)]
octeon: remove linux 4.4 support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agobuild: fix quilt for mixed package/host builds
Felix Fietkau [Wed, 3 May 2017 21:33:59 +0000 (23:33 +0200)]
build: fix quilt for mixed package/host builds

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agobuild: set QUILT=1 automatically when calling package host build refresh
Felix Fietkau [Wed, 3 May 2017 21:33:10 +0000 (23:33 +0200)]
build: set QUILT=1 automatically when calling package host build refresh

Makes behavor consistent with package builds and regular host builds

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agobuild: stop overriding STAGING_DIR_HOST for toolchain build
Felix Fietkau [Wed, 3 May 2017 13:01:03 +0000 (15:01 +0200)]
build: stop overriding STAGING_DIR_HOST for toolchain build

This causes various issues in other places that assume that host
binaries are staged in STAGING_DIR_HOST.
Since all the right places use HOST_BUILD_PREFIX, override that instead.
This fixes some issues with quilt on toolchain dirs

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agokernel: fix autoloading arch-specific modules
Yousong Zhou [Thu, 25 May 2017 06:41:34 +0000 (14:41 +0800)]
kernel: fix autoloading arch-specific modules

Fixes FS#745

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2 years agobacklight-pwm: fix module description
Yousong Zhou [Thu, 25 May 2017 06:40:36 +0000 (14:40 +0800)]
backlight-pwm: fix module description

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2 years agosysupgrade: run only one instance at a time.
Kenneth Johansson [Wed, 24 May 2017 11:45:37 +0000 (13:45 +0200)]
sysupgrade: run only one instance at a time.

Things do not work well if running multiple instances of
upgrade at the same time.

Signed-off-by: Kenneth Johansson <kenneth.johansson@inteno.se>
2 years agoinclude: Determine MODULES_DIR correctly for external/git kernels
Florian Fainelli [Thu, 11 May 2017 21:33:43 +0000 (14:33 -0700)]
include: Determine MODULES_DIR correctly for external/git kernels

When using external or git cloned kernels, any kind of modifications
will alter KERNELRELEASE. LEDE still tries to stage modules in
lib/modules/$(LINUX_UNAME_VERSION) and LINUX_UNAME_VERSION is based on
KERNEL_PATCHVER (indirectly) so this does not work, and we lose all
kinds of automatic modules loading.

To remedy that, just cat $(LINUX_DIR)/include/config/kernel.release
which is late enough the kernel has prepared this file, and is correctly
tracking changes done throughout the kernel.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2 years agoinclude: Do not alter KERNELRELEASE for external/git kernels
Florian Fainelli [Thu, 11 May 2017 21:33:42 +0000 (14:33 -0700)]
include: Do not alter KERNELRELEASE for external/git kernels

In case we use external and/or git cloned kernels, let the kernel
determine the appropriate KERNELRELEASE. We cannot used
LINUX_UNAME_VERSION because that one gets determined at a later time,
when the kernel is already built proper.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2 years agoRevert "kernel: prevent addition of scm marker to localversion"
Florian Fainelli [Thu, 11 May 2017 21:33:41 +0000 (14:33 -0700)]
Revert "kernel: prevent addition of scm marker to localversion"

This reverts commit 0df2c6563a3537ed21b28a9fb6874bf2718afd05 since it
gets in the way of identifying properly which kernel we are running.
This is particularly important if LEDE is using external kernels/git
cloned kernels. We want to make sure we only load modules from that
specific kernel.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2 years agokernel: add kmod-usb-net-pl package
Roman Spychała [Tue, 25 Apr 2017 11:07:37 +0000 (13:07 +0200)]
kernel: add kmod-usb-net-pl package

Kernel support for Prolific PL-2301/2302/25A1 based cables

Signed-off-by: Roman Spychała <roed@onet.eu>
2 years agoMake GBit switch work on RB2011
René Mayrhofer [Thu, 27 Apr 2017 08:08:39 +0000 (10:08 +0200)]
Make GBit switch work on RB2011

This change is required to make the GBit switch work on my Mikrotik Routerboard RB2011UiAS-RM, and I assume that the other RB2011 variants are exactly the same in terms of the switch. I have tested the board without and with the patch and confirm that the GBit ports are not supported at all (i.e. no communication works) with the current version in trunk and that everything works with the patch applied. The test box has been running for a few days with the patch applied, and does not show any performance problems in a test setting. I have not used it with LEDE in production so far, but with a previous turnk version of OpenWRT for many years - with the same patch applied. I therefore have good indication that it is stable.

For the record, the switch chip on my test box is identified as
switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0

The value 0x6f000000 has been taken from the table at https://wiki.openwrt.org/toh/mikrotik/rb2011uias with the previous discussion thread still online at https://lists.openwrt.org/pipermail/openwrt-devel/2014-December/029949.html.
One definite improvement from the older OpenWRT trunk version I have been running in production and current LEDE trunk is that the SFP interface can be kept in the default configuration without excessive kernel messages about it constantly going up and down. I have not yet tested an actual SFP module, though.

Performance seems to be reasonable. Routing between two GBit ports on that switch separated by different VLANs with the default firewall ruleset (and one additional rule two allow traffic between the VLANs), but without NAT, iperf3 results are:
[ ID] Interval           Transfer     Bandwidth       Retr
[  4]   0.00-10.00  sec   508 MBytes   426 Mbits/sec  102             sender
[  4]   0.00-10.00  sec   506 MBytes   425 Mbits/sec                  receiver
With a connection going through NAT (also 2 ports on the same GBit switch, same ruleset, but NAT active), routing performance drops to around 250 MBit/s.
(Note that RouterOS achieves beyond 900 MBit/s on the same hardware with the default rule set and the FastTrack rule active even for NAT, see https://wiki.mikrotik.com/index.php?title=Manual:IP/Fasttrack and http://www.mikrotik.com/download/share/FastTrack.pdf).

Summarizing, I strongly recommend to apply this patch in trunk, so that the GBit switch chip rev. 4 can be supported upstream in the next LEDE release (hopefully soon).

Signed-off-by: René Mayrhofer <rene@mayrhofer.eu.org>
2 years agoar71xx: change image version for ubiquiti devices
Matthias Fritzsche [Wed, 17 May 2017 03:44:49 +0000 (05:44 +0200)]
ar71xx: change image version for ubiquiti devices

changes the image version from hardcoded OpenWrt to
$VERSION_DIST. AirOS shows a notification with the image version
during a firmware upgrade.

fixes #582

Signed-off-by: Matthias Fritzsche <txt.file@txtfile.eu>
2 years agolldpd: bump to 0.9.7
Stijn Tintel [Wed, 24 May 2017 12:56:22 +0000 (14:56 +0200)]
lldpd: bump to 0.9.7

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2 years agosamba: fix CVE-2017-7494
Stijn Tintel [Wed, 24 May 2017 12:44:03 +0000 (14:44 +0200)]
samba: fix CVE-2017-7494

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>