openwrt/openwrt.git
22 months agoramips: add support for Edimax RG21S
Birger Koblitz [Thu, 19 Sep 2019 19:33:59 +0000 (21:33 +0200)]
ramips: add support for Edimax RG21S

SoC: MediaTek MT7621AT dual-core @ 880MHz
RAM: 256M (Nanya NT5CC128M)
FLASH: 16MB (Macronix MX25L12835F)
WiFi: - 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
USB: No
BTN: Reset, WPS
LED: 4 red LEDs, indistinguishable when casing closed
UART:  UART is present as Pads marked J1 on the PCB.
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad

Installation
------------
Update the factory image via the OEM web-interface
(by default:http://192.168.1.1)
The sysupgrade image can be installed via TFTP from
the U-Boot bootloader. Connect ethernet port 2.

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[flash node rename, EDIMAX -> Edimax, complete device model name]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
22 months agobrcm2708: fix Hifiberry DAC+DSP package definition
Álvaro Fernández Rojas [Fri, 20 Sep 2019 05:50:47 +0000 (07:50 +0200)]
brcm2708: fix Hifiberry DAC+DSP package definition

Fixes: ce536ae ("brcm2708: add support for Hifiberry DAC+DSP")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
22 months agokernel: Correctly search for the FIT image in mtd partition.
Fredrik Olofsson [Wed, 4 Sep 2019 08:41:22 +0000 (10:41 +0200)]
kernel: Correctly search for the FIT image in mtd partition.

Previously all iterations of the loop checked offset=0 in the partition.

Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
22 months agobuild: make device tree arg really optional in mkits.sh
Johann Neuhauser [Mon, 16 Sep 2019 09:42:49 +0000 (11:42 +0200)]
build: make device tree arg really optional in mkits.sh

If no device tree is given there is no node generated, but
the configuration does still include the name of the missing node.
This will result in a successful build fit image, but bootm does
throw a error message if we want to boot the bad configuration.

Signed-off-by: Johann Neuhauser <jneuhauser@dh-electronics.com>
22 months agolantiq-dsl: fix value of FECS counter
Martin Schiller [Mon, 26 Aug 2019 05:37:14 +0000 (07:37 +0200)]
lantiq-dsl: fix value of FECS counter

Instead of the nFECS value, the nFEC value (the number of corrected code words)
was mistakenly used.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
22 months agokernel: add module for Emulex OneConnect 10Gbit
Alberto Bursi [Sun, 15 Sep 2019 22:54:20 +0000 (00:54 +0200)]
kernel: add module for Emulex OneConnect 10Gbit

add module to support Emulex OneConnect
common in 10Gbit SFP+ cards by Dell/HP/IBM
supports OneConnect OCe10xxx OCe11xxx OCe14xxx,
LightPulse LPe12xxx

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
22 months agohostapd: declare struct wpa_bss early
Leon M. George [Wed, 11 Sep 2019 13:22:55 +0000 (15:22 +0200)]
hostapd: declare struct wpa_bss early

wps_supplicant.h assumes that 'struct wpa_bss' is forward declared if
CONFIG_WPS is not defined.  With the later inclusion of
600-ubus_support, the issue manifests in warnings like these:

wps_supplicant.h:113:15: warning: 'struct wpa_bss' declared inside parameter list will not be visible outside of this definition or declaration
        struct wpa_bss *bss)
               ^~~~~~~

This patch forward declares 'struct wpa_bss' regardless.

Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit message facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
22 months agohostapd: revert signature change in patch
Leon M. George [Wed, 11 Sep 2019 12:10:18 +0000 (14:10 +0200)]
hostapd: revert signature change in patch

The original wpa_hexdump uses a 'void *' for the payload.  With patch
410-limit_debug_messages, the signature changes and compiler warnings
occur at various places.  One such warning is:

 wpa_debug.h:106:20: note: expected 'const u8 * {aka const unsigned char *}' but argument is of type 'struct wpa_eapol_key *'

Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit message facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
22 months agoath79: add SUPPORTED_DEVICES to ubnt_nanostation-m-xw
Roger Pueyo Centelles [Tue, 17 Sep 2019 17:31:06 +0000 (19:31 +0200)]
ath79: add SUPPORTED_DEVICES to ubnt_nanostation-m-xw

The ar71xx images for the Ubiquiti NanoStation M (XW) devices use
"nanostation-m-xw" as the board name, but the ath79 images are only
compatible with the "nano-m-xw" board name, so sysupgrade complains.

By adding this additional supported device, sysuspgrade smoothly
upgrades from ar71xx to ath79.

Tested on a NanoStation M (XW) running OpenWrt ar71xx r10250-016d1eb.

Ref: https://github.com/openwrt/openwrt/pull/2418
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[removed duplicate DEVICE_VARIANT, removed uneeded nano-m-xw support]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
22 months agoath79: add XM device variant for Ubiquiti devices
Adrian Schmutzler [Wed, 18 Sep 2019 19:36:46 +0000 (21:36 +0200)]
ath79: add XM device variant for Ubiquiti devices

So far, XW devices have DEVICE_VARIANT defined and XM devices have
no DEVICE_VARIANT set.

This adds DEVICE_VARIANT for XM devices, and moves definitions for
both XM and XW to the common definitions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
22 months agoramips: provide label MAC address
Adrian Schmutzler [Mon, 24 Jun 2019 15:57:15 +0000 (17:57 +0200)]
ramips: provide label MAC address

This patch adds the label MAC address for several devices in
ramips.

Some devices require setting the MAC address in 02_network:

For the following devices, the netif device can be linked in
device tree, but the MAC address cannot be read:
- cudy,wr1000
- dlink,dir-615-d
- dlink,dir-615-h1
- dlink,dir-860l-b1
- glinet,gl-mt300a
- glinet,gl-mt300n
- glinet,gl-mt750
- vocore,vocore2
- vocore,vocore2-lite
- zbtlink,zbt-we1326
- zbtlink,zbt-wg3526

For the following devices, label MAC address is tied to lan or
wan, so no node to link to exists in device tree:
- dlink,dir-510l
- dlink,dwr-116-a1
- dlink,dwr-118-a1
- dlink,dwr-118-a2
- dlink,dwr-921-c1
- dlink,dwr-922-e2
- all hiwifi devices
- lava,lr-25g001
- xiaomi,mir3p

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
22 months agoipq806x: provide label MAC address
Adrian Schmutzler [Thu, 15 Aug 2019 13:13:44 +0000 (15:13 +0200)]
ipq806x: provide label MAC address

This patch adds the label MAC address for several devices in
ipq806x.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
22 months agompc85xx: provide label MAC address
Adrian Schmutzler [Thu, 15 Aug 2019 13:13:38 +0000 (15:13 +0200)]
mpc85xx: provide label MAC address

This patch adds the label MAC address for some devices in
mpc85xx.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
22 months agoath79: provide label MAC address
Adrian Schmutzler [Thu, 15 Aug 2019 13:13:33 +0000 (15:13 +0200)]
ath79: provide label MAC address

This patch adds the label MAC address for several devices in
ath79.

Some devices require setting the MAC address in 02_network:

For the following devices, the netif device can be linked in
device tree, but the MAC address cannot be read:
- alfa-network,ap121f
- avm,fritz300e
- ubnt-xm devices

For the following devices, label MAC address is tied to lan or
wan, so no node to link to exists in device tree:
- adtran,bsap1800-v2
- adtran,bsap1840
- dlink,dir-842-c1/-c2/-c3
- engenius,ecb1750
- iodata,etg3-r
- iodata,wn-ac1167dgr
- iodata,wn-ac1600dgr
- iodata,wn-ac1600dgr2
- iodata,wn-ag300dgr
- nec,wg800hp
- nec,wg1200cr
- trendnet,tew-823dru

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
22 months agobase-files: provide option to specify label MAC address in board.d
Adrian Schmutzler [Thu, 15 Aug 2019 13:13:27 +0000 (15:13 +0200)]
base-files: provide option to specify label MAC address in board.d

For many devices, MAC addresses cannot be retrieved via the
device tree alias.

To still provide the label MAC address for those, this implements
a second mechanism that will put the address into uci config.
Note that this stores the actual MAC address, whereas in DTS
we reference the bearing device.

This is based on the work of Rosy Song <rosysong@rosinson.com>

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
22 months agobase-files: add function to retrieve label MAC address
Adrian Schmutzler [Thu, 15 Aug 2019 13:13:21 +0000 (15:13 +0200)]
base-files: add function to retrieve label MAC address

To refer to the MAC address on a device's label, one can
specify the alias label-mac-device in the DTS which should
point to the bearer of the corresponding MAC address.

With the function get_mac_label, the user can retrieve then
retrieve this address and use it as a value that uniquely
identifies his device.

This is severely helpful for several downstream functionalities,
e.g. define MAC addresses of custom netifs or change the SSID to
be easily recognizable.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
22 months agocurl: bump to 7.66.0
Hans Dedecker [Tue, 17 Sep 2019 20:45:41 +0000 (22:45 +0200)]
curl: bump to 7.66.0

Refresh patches, for changes in version 7.66.0 see https://curl.haxx.se/changes.html#7_66_0

Fixes CVEs:
    CVE-2019-5481
    CVE-2019-5482

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
22 months agoopenssl: bump to 1.1.1d
Eneas U de Queiroz [Tue, 17 Sep 2019 13:52:11 +0000 (10:52 -0300)]
openssl: bump to 1.1.1d

This version fixes 3 low-severity vulnerabilities:

- CVE-2019-1547: ECDSA remote timing attack
- CVE-2019-1549: Fork Protection
- CVE-2019-1563: Padding Oracle in PKCS7_dataDecode and
 CMS_decrypt_set1_pkey

Patches were refreshed.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
22 months agobrcm2708: add support for Hifiberry DAC+DSP
Álvaro Fernández Rojas [Thu, 19 Sep 2019 16:06:50 +0000 (18:06 +0200)]
brcm2708: add support for Hifiberry DAC+DSP

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
22 months agobrcm2708: add support for Raspberry Pi 2B 1.2
Álvaro Fernández Rojas [Thu, 19 Sep 2019 15:32:44 +0000 (17:32 +0200)]
brcm2708: add support for Raspberry Pi 2B 1.2

RPi 2B 1.2 has a BCM2710/BCM2837 like RPi 3 devices.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
22 months agobrcm2708: update to latest patches from RPi foundation
Álvaro Fernández Rojas [Thu, 19 Sep 2019 14:43:19 +0000 (16:43 +0200)]
brcm2708: update to latest patches from RPi foundation

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
22 months agobrcm2708-gpu-fw: update to latest firmware
Álvaro Fernández Rojas [Thu, 19 Sep 2019 15:37:43 +0000 (17:37 +0200)]
brcm2708-gpu-fw: update to latest firmware

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
22 months agokernel: 4.19: fix crash when setting up spi-gpio
DENG Qingfang [Thu, 19 Sep 2019 09:44:48 +0000 (11:44 +0200)]
kernel: 4.19: fix crash when setting up spi-gpio

If an spi-gpio was specified with num-chipselects = <0> in dts, kernel
will crash:

 Unable to handle kernel paging request at virtual address 32697073
 pgd = (ptrval)
 [32697073] *pgd=00000000
 Internal error: Oops: 5 [# 1] SMP ARM
 Modules linked in:
 CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.19.72 #0
 Hardware name: Generic DT based system
 PC is at validate_desc+0x28/0x80
 LR is at gpiod_direction_output+0x14/0x128
 ...
 [<c0544db4>] (validate_desc) from [<c0545228>] (gpiod_direction_output+0x14/0x128)
 [<c0545228>] (gpiod_direction_output) from [<c05fa714>] (spi_gpio_setup+0x58/0x64)
 [<c05fa714>] (spi_gpio_setup) from [<c05f7258>] (spi_setup+0x12c/0x148)
 [<c05f7258>] (spi_setup) from [<c05f7330>] (spi_add_device+0xbc/0x12c)
 [<c05f7330>] (spi_add_device) from [<c05f7f74>] (spi_register_controller+0x838/0x924)
 [<c05f7f74>] (spi_register_controller) from [<c05fa494>] (spi_bitbang_start+0x108/0x120)
 [<c05fa494>] (spi_bitbang_start) from [<c05faa34>] (spi_gpio_probe+0x314/0x338)
 [<c05faa34>] (spi_gpio_probe) from [<c05a844c>] (platform_drv_probe+0x34/0x70)

The cause is spi_gpio_setup() did not check if the spi-gpio has
chipselect pins before setting their direction and results in derefing
an invalid pointer.

The bug is spotted in kernel 4.19.72 and does not occur in 4.14.

There is a similar fix upstream in kernel 5.2 in commit 249e2632dcd0
("spi: gpio: Don't request CS GPIO in DT use-case").

Ref: https://patchwork.kernel.org/patch/11150619/
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[use upstream patch, moved from hack to pending dir, commit facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
22 months agoprocd: fix invalid JSON filter expression in procd_running()
Jo-Philipp Wich [Thu, 19 Sep 2019 05:16:49 +0000 (07:16 +0200)]
procd: fix invalid JSON filter expression in procd_running()

Since service and instance names may contain characters which are not allowed
in JSON path labels, such as dashes or spaces, change the filter expression
to array square bracket notation to properly match these cases as well.

Fixes: 2c3dd70741 ("procd: add procd_running() helper for checking running state")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
22 months agofirewall: update to latest Git HEAD
Jo-Philipp Wich [Wed, 18 Sep 2019 08:51:24 +0000 (10:51 +0200)]
firewall: update to latest Git HEAD

383eb58 ubus: do not overwrite ipset name attribute

Ref: https://forum.openwrt.org/t/fw3-ipset-procd-objects/44044
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
22 months agoprocd: update to the latest git HEAD
Rafał Miłecki [Wed, 18 Sep 2019 05:33:01 +0000 (07:33 +0200)]
procd: update to the latest git HEAD

62dc8c0 system: sysupgrade: send reply on error
2710c65 system: refuse sysupgrade with backup if it's unsupported

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
22 months agoglibc: update to latest 2.27 commit (BZ#23637)
Hans Dedecker [Tue, 17 Sep 2019 20:11:26 +0000 (22:11 +0200)]
glibc: update to latest 2.27 commit (BZ#23637)

5b4f7382af Add undef to fix test failure.
9456483fb2 Improve performance of memmem
373f8b06a3 Improve performance of strstr
4ec1b9e913 Fix strstr bug with huge needles (bug 23637)
ecd6271ed8 Speedup first memmem match
bba6b9288f Simplify and speedup strstr/strcasestr first match
7a4da6ef7a Improve strstr performance

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
22 months agoath79: add support for TP-Link Archer C59v2
Keith Maika [Mon, 16 Sep 2019 16:45:02 +0000 (12:45 -0400)]
ath79: add support for TP-Link Archer C59v2

Add ath79 support for Archer C59v2, previously supported by ar71xx.

TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB

Flash instruction:
  - via web UI:
    1. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin
    2. Login to router and open the Advanced tab
    3. Navigate to System Tools -> Firmware Upgrade
    4. Upload firmware using the Manual Upgrade form
  - via TFTP:
    1. Set PC to fixed ip address 192.168.0.66
    2. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin
       and rename it to tp_recovery.bin
    3. Start a tftp server with the file tp_recovery.bin in its root directory
    4. Turn off the router
    5. Press and hold Reset button
    6. Turn on router with the reset button pressed and wait ~15 seconds
    7. Release the reset button and after a short time
       the firmware should be transferred from the tftp server
    8. Wait ~30 second to complete recovery.

Signed-off-by: Keith Maika <keithm@aoeex.com>
22 months agoath79: move common definitions from Archer C58/C59 to common DTSI
Adrian Schmutzler [Sun, 1 Sep 2019 08:59:31 +0000 (10:59 +0200)]
ath79: move common definitions from Archer C58/C59 to common DTSI

The Archer C58/C59 have redundant LED and MAC address definitions
in their DTS files. This moves them to the parent DTSI file.

The patch already accounts for the upcoming Archer C59 v2.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
22 months agobrcm47xx: sysupgrade: support Luxul firmware format
Dan Haab [Mon, 16 Sep 2019 15:18:37 +0000 (09:18 -0600)]
brcm47xx: sysupgrade: support Luxul firmware format

Allow flashing Luxul devices using vendor firmware format.

Signed-off-by: Dan Haab <dan.haab@legrand.com>
22 months agobcm53xx: sysupgrade: support Luxul firmware format
Dan Haab [Thu, 12 Sep 2019 17:14:19 +0000 (11:14 -0600)]
bcm53xx: sysupgrade: support Luxul firmware format

Allow flashing Luxul devices using vendor firmware format. The next step
will be building proper images once they are conirmed to work.

Signed-off-by: Dan Haab <dan.haab@legrand.com>
22 months agodownload.dl: fix @KERNEL mirror urls
Yousong Zhou [Mon, 16 Sep 2019 08:02:16 +0000 (08:02 +0000)]
download.dl: fix @KERNEL mirror urls

 - Prepend "/pub" for mirror.rackspace.com
 - Use https for download.xs4all.nl and mirrors.mit.edu

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
22 months agomac80211: brcmfmac: backport the last 5.4 changes
Rafał Miłecki [Mon, 16 Sep 2019 06:04:27 +0000 (08:04 +0200)]
mac80211: brcmfmac: backport the last 5.4 changes

This makes brcmfmac use the same wiphy after PCIe reset to help user
space handle corner cases (e.g. firmware crash).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
22 months agoar71xx: fix typo in platform_do_upgrade_compex()
Rafał Miłecki [Mon, 16 Sep 2019 04:59:09 +0000 (06:59 +0200)]
ar71xx: fix typo in platform_do_upgrade_compex()

Fixes: 641f6b6c26cb ("treewide: use new procd sysupgrade $UPGRADE_BACKUP variable")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
22 months agomediatek: enable mtk_efuse by default
Lorenzo Bianconi [Fri, 6 Sep 2019 11:14:39 +0000 (13:14 +0200)]
mediatek: enable mtk_efuse by default

Enable by default mtk_efuse driver since it needed by mtk_thermal driver
to read sensor calibration data

Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
22 months agoath79: eg200: enable status led usage
Karl Palsson [Thu, 5 Sep 2019 09:36:53 +0000 (09:36 +0000)]
ath79: eg200: enable status led usage

This enables using the "eTactica" LED during boot, to indicate failsafe,
and during upgrade, while still leaving the LED alone for normal
operation.  This brings the device more in line with how other devices
work, and makes the failsafe functionality easier to use and understand.

Signed-off-by: Karl Palsson <karlp@etactica.com>
22 months agofirewall: update to latest git HEAD
Petr Štetiar [Sun, 15 Sep 2019 19:19:00 +0000 (21:19 +0200)]
firewall: update to latest git HEAD

c26f8907d1d2 firewall3: fix typo that affects ICMPv6 rules with numeric icmp_type

Signed-off-by: Petr Štetiar <ynezz@true.cz>
22 months agoath10k-ct: update to version 2019-09-09
Robert Marko [Fri, 13 Sep 2019 10:15:39 +0000 (12:15 +0200)]
ath10k-ct: update to version 2019-09-09

Update the ath10k-ct driver version to 5e8cd86f90dac966d12df6ece84ac41458d0e95f
to enable dynamic VLANs to work. Patches refreshed during the bump.

Signed-off-by: Robert Marko <robimarko@gmail.com>
[commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
22 months agoath10k-firmware: update Candela Tech firmware images
Robert Marko [Fri, 13 Sep 2019 10:15:37 +0000 (12:15 +0200)]
ath10k-firmware: update Candela Tech firmware images

This enables a feature flag in the wave-2 firmware wmi-services indicating it can send
software-encrypted raw frames.  This should in turn allow the AP-VLAN feature to work.

Signed-off-by: Robert Marko <robimarko@gmail.com>
22 months agoscons: move to packages feed
Petr Štetiar [Sat, 27 Jul 2019 22:33:32 +0000 (00:33 +0200)]
scons: move to packages feed

This patch removes scons host build tool, as commit 7087efd72a8d
("scons: move host build tool to a proper place") in the packages feed
has moved scons into the new home.

There are currently no packages in the master tree which would need
scons, yet scons is build always as part of host tools, just in order to
satisfy host build dependency of few packages in the packages feeds.

Ref: https://github.com/openwrt/packages/pull/9584
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
22 months agonetifd,lldpd,rpcd,log: use generic service_running
Petr Štetiar [Tue, 23 Jul 2019 10:16:03 +0000 (12:16 +0200)]
netifd,lldpd,rpcd,log: use generic service_running

commit eb204d14f75c ("base-files: implement generic service_running")
introduced generic service_running so it's not needed to copy&paste same
3 lines over and over again.

I've removed service_running from netifd/network init script as well,
because it was not working properly, looked quite strange and I didn't
understand the intention:

 $ /etc/init.d/network stop
 $ service network running && echo "yes" || echo "nope"
     ( have to wait for 30s )
 Command failed: Request timed out
 yes

Signed-off-by: Petr Štetiar <ynezz@true.cz>
22 months agobase-files,procd: add generic service status
Luiz Angelo Daros de Luca [Wed, 12 Sep 2018 01:35:09 +0000 (22:35 -0300)]
base-files,procd: add generic service status

Adds a default status action for init.d scripts.

procd "service status" will return:

 0) for loaded services (even if disabled by conf or dead)
 3) for inactive services
 4) when filtering a non-existing instance

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
[rebased, cleaned up]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
22 months agobase-files: implement generic service_running
Petr Štetiar [Tue, 23 Jul 2019 10:06:29 +0000 (12:06 +0200)]
base-files: implement generic service_running

DRY is good, otherwise we're going to suffer with a copy&paste disease
in the init scripts.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
22 months agoodhcpd: update to latest git HEAD
Hans Dedecker [Sun, 15 Sep 2019 18:40:16 +0000 (20:40 +0200)]
odhcpd: update to latest git HEAD

1d24009 netlink: rename netlink callback handlers
91a28e4 ndp: answer global-addressed NS manually
fd93e36 dhcpv6: retry failed PD assignments on addrlist change

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
22 months agoramips: add SD-Card support for Linkit Smart 7688
Ivan Hörler [Sat, 14 Sep 2019 15:25:04 +0000 (17:25 +0200)]
ramips: add SD-Card support for Linkit Smart 7688

The Linkit Smart 7688 has a SD-Card reader that does not work with the official build of openwrt. Adding kmod-sdhci-mt7620 makes it working.

Signed-off-by: Ivan Hörler <i.hoerler@me.com>
22 months agoramips: only add spidev node in for WrtNode2R (and not for 2P)
Daniel Golle [Sun, 15 Sep 2019 18:14:26 +0000 (20:14 +0200)]
ramips: only add spidev node in for WrtNode2R (and not for 2P)

Only the 2R version got the STM32 uC connected as 2nd SPI device.
Hence move the spidev node from mt7628an_wrtnode_wrtnode2.dtsi to
mt7628an_wrtnode_wrtnode2r.dts.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
22 months agoscripts/feeds: fix accepting "-" in feed type string
Felix Fietkau [Sun, 15 Sep 2019 17:53:17 +0000 (19:53 +0200)]
scripts/feeds: fix accepting "-" in feed type string

Fixes a syntax error in processing the type src-git-full

Signed-off-by: Felix Fietkau <nbd@nbd.name>
22 months agoapm821xx: image: remove unused kernel.dtb from IMAGES
Yousong Zhou [Tue, 10 Sep 2019 13:10:08 +0000 (13:10 +0000)]
apm821xx: image: remove unused kernel.dtb from IMAGES

It's a leftover from 2271967f ("apm821xx: utilize build ARTIFACTs")

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
22 months agoimx6: install-dtb as separate IMAGE
Yousong Zhou [Thu, 12 Sep 2019 07:37:05 +0000 (07:37 +0000)]
imx6: install-dtb as separate IMAGE

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
22 months agobuild: install-dtb: fix race condition when copying dtb
Yousong Zhou [Tue, 10 Sep 2019 13:40:43 +0000 (13:40 +0000)]
build: install-dtb: fix race condition when copying dtb

Currently for at91 target, Build/install-dtb can be triggered concurrently for
multiple different TARGET_FILESYSTEMS, cp command can fail when the
target file is already open exclusively by other cp process

[ -f /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/at91sam9263ek-uImage -a -f /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/root.ubifs+fs=-m_2048_-e_126KiB_-c_2048+pkg=68b329da ]
[ -f /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/at91sam9263ek-uImage -a -f /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/root.ext4+pkg=68b329da ]
cp -fpR /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/linux-4.14.141/arch/arm/boot/dts/at91sam9263ek.dtb /builder/shared-workdir/build/bin/targets/at91/sam9x/openwrt-at91-sam9x-at91sam9263ek.dtb;
cp -fpR /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/linux-4.14.141/arch/arm/boot/dts/at91sam9263ek.dtb /builder/shared-workdir/build/bin/targets/at91/sam9x/openwrt-at91-sam9x-at91sam9263ek.dtb;
cp: cannot create regular file '/builder/shared-workdir/build/bin/targets/at91/sam9x/openwrt-at91-sam9x-at91sam9263ek.dtb': File exists
Makefile:87: recipe for target '/builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/tmp/openwrt-at91-sam9x-at91sam9263ek-ubifs-dtb' failed
make[4]: *** [/builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/tmp/openwrt-at91-sam9x-at91sam9263ek-ubifs-dtb] Error 1

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
22 months agoar71xx: make IRQ fixes target specific
Koen Vandeputte [Sat, 14 Sep 2019 14:21:57 +0000 (16:21 +0200)]
ar71xx: make IRQ fixes target specific

Move the IRQ fix from generic to ar71xx specific.
Other targets like ath79 have specific pathes to delete this code.
This resulted in a build failure on ath79

While at it, wipe the 4.19 version, as ar71xx will never reach this.

Fixes: 530f76708cef ("ar71xx: Fix potentially missed IRQ handling during
dispatch")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
22 months agobrcm63xx: remove redundant variable definition in Makefile
Adrian Schmutzler [Wed, 11 Sep 2019 18:56:48 +0000 (20:56 +0200)]
brcm63xx: remove redundant variable definition in Makefile

For devices inheriting from bcm63xx_netgear, the IMAGES variable
is overwritten with the same values as defined in the parent
definition. So, remove the unnecessary overwrite.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
22 months agoimages: fix boot failures on NAND with small sub pages
Jonas Gorski [Tue, 3 Sep 2019 12:16:12 +0000 (14:16 +0200)]
images: fix boot failures on NAND with small sub pages

SquashFS has a minimum block size of at least 1k, so we need to make
sure the last data block is also at least that big.

This is not an issue on NOR or SD CARD devices, since their rootfs
partitions go all the way to the end of the usable space.

But on NAND with ubiblock, the rootfs partition will be the exact space,
rounded up to LEB size. Unfortunately, some NAND chips with small sub
pages have a LEB size of x.5 kiB. This can cause the the last data block
to be less than 1k, which will cause the last block to be inaccessible,
causing boot failures as seen on MR24:

[    1.532960] block ubiblock0_3: created from ubi0:3(rootfs)
[    1.538457] ubiblock: device ubiblock0_3 (rootfs) set to be root filesystem
[    1.552847] SQUASHFS error: squashfs_read_data failed to read block 0x621472
[    1.559896] squashfs: SQUASHFS error: unable to read id index table
[    1.566474] VFS: Cannot open root device "(null)" or unknown-block(254,0): error -5

Since on most NOR devices, the start of the squashfs partition is not
aligned. Since the start of the rootfs_data partition there is dependend
on the SquashFS size, we cannot just always pad it, as the padding could
creep into the rootfs_data partition, breaking jffs2.

So fix this by ensuring a squashfs rootfs is always a multiple of 1k
only for UBI and NAND sysupgrade images.

Fixes #2460 without affecting NOR devices.

Tested-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
22 months agoar71xx: fix potential IRQ misses during dispatch for qca953x
Koen Vandeputte [Wed, 11 Sep 2019 10:47:27 +0000 (12:47 +0200)]
ar71xx: fix potential IRQ misses during dispatch for qca953x

If both interrupts are set in the current implementation
only the 1st will be handled and the 2nd will be skipped
due to the "if else" condition.

Fix this by using the same approach as done for QCA955x
just below it.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
22 months agoar71xx: Fix potentially missed IRQ handling during dispatch
Koen Vandeputte [Wed, 11 Sep 2019 10:22:42 +0000 (12:22 +0200)]
ar71xx: Fix potentially missed IRQ handling during dispatch

If both interrupts are set in the current implementation
only the 1st will be handled and the 2nd will be skipped
due to the "if else" condition.

Fix this by using the same approach as done for QCA955x
just below it.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
22 months agokernel: bump 4.19 to 4.19.72
Koen Vandeputte [Wed, 11 Sep 2019 09:35:24 +0000 (11:35 +0200)]
kernel: bump 4.19 to 4.19.72

Refreshed all patches.

Remove upstreamed:
- 390-v5.3-net-sched-fix-action-ipt-crash.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
22 months agokernel: bump 4.14 to 4.14.143
Koen Vandeputte [Wed, 11 Sep 2019 09:34:00 +0000 (11:34 +0200)]
kernel: bump 4.14 to 4.14.143

Refreshed all patches.

Remove upstreamed:
- 390-v5.3-net-sched-fix-action-ipt-crash.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
22 months agokernel: bump 4.9 to 4.9.192
Koen Vandeputte [Wed, 11 Sep 2019 09:19:39 +0000 (11:19 +0200)]
kernel: bump 4.9 to 4.9.192

Refreshed all patches.

Compile-tested on: none
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
22 months agoodhcpd: fix update to git HEAD
Hans Dedecker [Thu, 12 Sep 2019 20:31:01 +0000 (22:31 +0200)]
odhcpd: fix update to git HEAD

Fixes commit 7ff5b12e90

e73bf11 config: ra_management compatibility support
d818380 odhcpd: router: Fix out of scope memory access
94a1c94 dhcpv6-ia: free assignment when validity timer expires
752fc2c router: speed up initial router advertisements
09aa022 router: close socket upon NETEV_IFINDEX_CHANGE fixed
79eb160 router: fix previous commit
6034b5c router: close socket upon NETEV_IFINDEX_CHANGE
000182f router: fix lingering uloop socket descriptor
f6c2242 router: support ra_lifetime being 0

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
22 months agoumbim: update to latest git HEAD
Ingo Feinerer [Wed, 11 Sep 2019 11:14:05 +0000 (13:14 +0200)]
umbim: update to latest git HEAD

184b707 umbim: add home provider query support

Signed-off-by: Ingo Feinerer <feinerer@logic.at>
22 months agoodhcpd: update to latest git HEAD (FS#2019)
Hans Dedecker [Sat, 29 Jun 2019 19:07:12 +0000 (21:07 +0200)]
odhcpd: update to latest git HEAD (FS#2019)

e73bf11 config: ra_management compatibility support
d818380 odhcpd: router: Fix out of scope memory access
94a1c94 dhcpv6-ia: free assignment when validity timer expires
752fc2c router: speed up initial router advertisements
09aa022 router: close socket upon NETEV_IFINDEX_CHANGE fixed
79eb160 router: fix previous commit
6034b5c router: close socket upon NETEV_IFINDEX_CHANGE
000182f router: fix lingering uloop socket descriptor
f6c2242 router: support ra_lifetime being 0
d111809 router: make RA flags configurable (FS#2019)

Update odhcpd defaults according to the new RA flags implementation

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
22 months agomt76: probe load mt7615 driver asynchronously
Felix Fietkau [Thu, 12 Sep 2019 15:15:40 +0000 (17:15 +0200)]
mt76: probe load mt7615 driver asynchronously

It can take a long time to load the firmware

Signed-off-by: Felix Fietkau <nbd@nbd.name>
22 months agoath79: fix UniFi AC LED mapping
David Bauer [Fri, 6 Sep 2019 22:43:19 +0000 (00:43 +0200)]
ath79: fix UniFi AC LED mapping

The UniFi AC LED mapping is currently off. The blue/white LED are used
as WiFi indicators, while the vendor firmware does not feature WiFI
LEDs.

Instead, the LEDs are used to indicate the devices status. Align the LED
mapping to match the vendor firmware as good as possible.

Signed-off-by: David Bauer <mail@david-bauer.net>
22 months agoiwinfo: update to latest Git HEAD
David Bauer [Sun, 8 Sep 2019 13:48:43 +0000 (15:48 +0200)]
iwinfo: update to latest Git HEAD

a88fb42 iwinfo: add device id for Qualcomm Atheros QCA9886
1b69d86 iwinfo: add device id for Qualcomm Atheros QCA9887

Signed-off-by: David Bauer <mail@david-bauer.net>
22 months agoconfig: kernel: only enable container features if !SMALL_FLASH
Daniel Golle [Thu, 12 Sep 2019 11:17:24 +0000 (13:17 +0200)]
config: kernel: only enable container features if !SMALL_FLASH

KERNEL_DEVPTS_MULTIPLE_INSTANCES and KERNEL_POSIX_MQUEUE were
previously enabled by default only if KERNEL_LXC_MISC was selected.
KERNEL_LXC_MISC was enabled only if the SMALL_FLASH (anti-)feature
was not selected.
Now that KERNEL_LXC_MISC no longer exists, make sure that those
options are also only enabled by default for !SMALL_FLASH targets.

Fixes: 4f94a331 ("config: kernel: remove KERNEL_LXC_MISC")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
22 months agoconfig: kernel: remove KERNEL_LXC_MISC
Yousong Zhou [Tue, 27 Aug 2019 06:35:10 +0000 (06:35 +0000)]
config: kernel: remove KERNEL_LXC_MISC

Kernel features are neutral.  The two cascaded features can also be
useful for other container related tools

It's also less error-prone if only kconfig symbols from the kernel are
prefixed KERNEL_

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
22 months agoconfig: kernel: add KERNEL_X86_VSYSCALL_EMULATION
Yousong Zhou [Tue, 27 Aug 2019 03:52:56 +0000 (03:52 +0000)]
config: kernel: add KERNEL_X86_VSYSCALL_EMULATION

Binaries in container images may need this.  E.g. nginx:1.7.9 used in
k8s default deployment manifest file for demostration [1]

 [1] https://kubernetes.io/docs/concepts/workloads/controllers/deployment/#creating-a-deployment

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
22 months agoRevert "ar71xx: use platform code for qca955x usb0 init"
Koen Vandeputte [Wed, 11 Sep 2019 21:40:42 +0000 (23:40 +0200)]
Revert "ar71xx: use platform code for qca955x usb0 init"

This reverts commit 5b98061bb1ac7e3affadda7b55c6f4ed4eb8268e.

As Piotr Dymacz pointed out:

In QCA MIPS based WiSOCs, for first USB interface,
device/host mode can be selected _only_ in hardware
see description of 57c641ba6e

QCA955x and QCA9563, second USB can be switched to device
mode in software (tested and confirmed on real hardware).

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
22 months agoimx6: split up DEVICE_TITLE
Moritz Warning [Mon, 9 Sep 2019 22:03:07 +0000 (00:03 +0200)]
imx6: split up DEVICE_TITLE

DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT

Signed-off-by: Moritz Warning <moritzwarning@web.de>
22 months agosamsung: split up DEVICE_TITLE
Moritz Warning [Mon, 9 Sep 2019 22:15:49 +0000 (00:15 +0200)]
samsung: split up DEVICE_TITLE

DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT

Signed-off-by: Moritz Warning <moritzwarning@web.de>
22 months agoar71xx: qca955x pci init/reset fixes
Tomislav Požega [Tue, 3 Sep 2019 22:48:37 +0000 (00:48 +0200)]
ar71xx: qca955x pci init/reset fixes

Current ar724x code does the reset only on single pci bus, and
in case of qca9558 writes the wrong register (0x10 vs 0x0c).
This change allows the reset of second pci bus, commonly used in
Archer C7 devices, in case host controller is stuck in reset.
If the resetting controller on boot can solve any other issue it
can be enabled unconditionally by removing reset check before
ar724x_pci_hw_init is called.

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
[refreshed to apply cleanly]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
22 months agoar71xx: enable ddr wb flush on qca955x
Tomislav Požega [Tue, 3 Sep 2019 15:10:31 +0000 (17:10 +0200)]
ar71xx: enable ddr wb flush on qca955x

Enable flushing of write buffers on qca955x. GPL code has 0x88 reg
defined for PCI flush which is likely an error since the device
freezes on boot. So use DS default value 0xA8 for PCI flush.

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
22 months agoar71xx: use platform code for qca955x usb0 init
Tomislav Požega [Tue, 3 Sep 2019 15:04:17 +0000 (17:04 +0200)]
ar71xx: use platform code for qca955x usb0 init

Switch from ci_usb_setup to generic platform initialization of
usb0 port.

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
22 months agokernel: bump 4.19 to 4.19.71
Koen Vandeputte [Mon, 9 Sep 2019 11:24:41 +0000 (13:24 +0200)]
kernel: bump 4.19 to 4.19.71

Refreshed all patches.

Remove upstreamed:
- 950-0774-watchdog-bcm2835_wdt-Fix-module-autoload.patch
- 0017-usb-host-fotg2-restart-hcd-after-port-reset.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
22 months agokernel: bump 4.14 to 4.14.142
Koen Vandeputte [Mon, 9 Sep 2019 11:24:19 +0000 (13:24 +0200)]
kernel: bump 4.14 to 4.14.142

Refreshed all patches.

Remove upstreamed:
- 0032-usb-host-fotg2-restart-hcd-after-port-reset.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
22 months agokernel: bump 4.9 to 4.9.191
Koen Vandeputte [Mon, 9 Sep 2019 11:21:20 +0000 (13:21 +0200)]
kernel: bump 4.9 to 4.9.191

Refreshed all patches.

Compile-tested on: none
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
22 months agotreewide: sysupgrade: use $UPGRADE_BACKUP to check for backup
Rafał Miłecki [Fri, 6 Sep 2019 05:10:54 +0000 (07:10 +0200)]
treewide: sysupgrade: use $UPGRADE_BACKUP to check for backup

Now that $UPGRADE_BACKUP is set conditionally there is no need to check
the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
22 months agoprocd: update to the latest git HEAD
Rafał Miłecki [Wed, 11 Sep 2019 07:03:36 +0000 (09:03 +0200)]
procd: update to the latest git HEAD

b8238df sysupgrade: support "backup" attribute

This update requires "sysupgrade" method callers to pass "backup"
attribute if $UPGRADE_BACKUP is used in the project.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
22 months agobase-files: sysupgrade: pass "backup" ubus attribute
Rafał Miłecki [Fri, 6 Sep 2019 05:10:52 +0000 (07:10 +0200)]
base-files: sysupgrade: pass "backup" ubus attribute

This explicitly tells procd what backup file should be used during
sysupgrade (if any). It's much more generic this way compared to the
magic /tmp/sysupgrade.tgz file that had to be created before a call.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
22 months agogemini: image: fix race condition when building copy-kernel.bin
Yousong Zhou [Tue, 10 Sep 2019 02:19:05 +0000 (02:19 +0000)]
gemini: image: fix race condition when building copy-kernel.bin

Make treat copy-kernel.o as intermediate and delete it when it's no
longer needed.  This can fail when the same submake was triggered
multiple times for different devices.

arm-openwrt-linux-muslgnueabi-as  -k -o copy-kernel.o copy-kernel.S
export MAKEFLAGS= ;make -w -C copy-kernel CROSS_COMPILE=arm-openwrt-linux-muslgnueabi-
arm-openwrt-linux-muslgnueabi-objcopy -O binary -S copy-kernel.o copy-kernel.bin
make[5]: Entering directory '/builder/shared-workdir/build/target/linux/gemini/image/copy-kernel'
arm-openwrt-linux-muslgnueabi-objcopy -O binary -S copy-kernel.o copy-kernel.bin
rm copy-kernel.o
make[5]: Leaving directory '/builder/shared-workdir/build/target/linux/gemini/image/copy-kernel'
# "App" partition is the rootfs
arm-openwrt-linux-muslgnueabi-objcopy: 'copy-kernel.o': No such file
Makefile:27: recipe for target 'copy-kernel.bin' failed
make[5]: Leaving directory '/builder/shared-workdir/build/target/linux/gemini/image/copy-kernel'
make[5]: *** [copy-kernel.bin] Error 1
Makefile:244: recipe for target '/builder/shared-workdir/build/build_dir/target-arm_fa526_musl_eabi/linux-gemini/tmp/openwrt-gemini-storlink_sl93512r-ext4-factory.bin' failed
make[4]: *** [/builder/shared-workdir/build/build_dir/target-arm_fa526_musl_eabi/linux-gemini/tmp/openwrt-gemini-storlink_sl93512r-ext4-factory.bin] Error 2

With this change, output files are directed to $(KDIR)

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
22 months agohostapd: SAE/EAP-pwd side-channel attack update
Hauke Mehrtens [Sun, 8 Sep 2019 21:53:18 +0000 (23:53 +0200)]
hostapd: SAE/EAP-pwd side-channel attack update

Fixes this security problem:
* SAE/EAP-pwd side-channel attack update
https://w1.fi/security/2019-6/sae-eap-pwd-side-channel-attack-update.txt

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
22 months agohostapd: Fix security problem
Hauke Mehrtens [Sun, 8 Sep 2019 21:27:04 +0000 (23:27 +0200)]
hostapd: Fix security problem

This fixes:
CVE-2019-11555 "EAP-pwd message reassembly issue with unexpected fragment"
https://w1.fi/security/2019-5/eap-pwd-message-reassembly-issue-with-unexpected-fragment.txt

This shouöld not affect OpenWrt in the default settings as we do not use
EAP-pwd.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
22 months agoramips: enable external amplifier for D-Link DIR-810L
Roger Pueyo Centelles [Wed, 4 Sep 2019 09:29:12 +0000 (11:29 +0200)]
ramips: enable external amplifier for D-Link DIR-810L

The 2.4 GHz radio had very poor signal reception (-89 dBm for an AP
sitting 5 m away). By enabling the external amplifier, received signal
has improved to -50 dBm for the same AP.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
22 months agorpcd: update to latest Git HEAD
Jo-Philipp Wich [Tue, 10 Sep 2019 13:25:12 +0000 (15:25 +0200)]
rpcd: update to latest Git HEAD

e2a7bc4 iwinfo: add WPA3 support

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
22 months agomac80211: brcmfmac: backport more kernel 5.4 changes
Rafał Miłecki [Mon, 9 Sep 2019 07:37:53 +0000 (09:37 +0200)]
mac80211: brcmfmac: backport more kernel 5.4 changes

Patch getting RAM info got upstreamed. A debugging fs entry for testing
reset feature was added.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
22 months agoglibc: update to latest 2.27 commit (BZ #24228, BZ #24744, BZ #24699)
Hans Dedecker [Sun, 8 Sep 2019 19:13:59 +0000 (21:13 +0200)]
glibc: update to latest 2.27 commit (BZ #24228, BZ #24744, BZ #24699)

5f0d2e0491 [AArch64] Add ifunc support for Ares
e6b7252040 aarch64,falkor: Use vector registers for memcpy
c74b884f70 aarch64,falkor: Ignore prefetcher tagging for smaller copies
0fc5934ebd aarch64/strncmp: Use lsr instead of mov+lsr
e0a0bd3acc aarch64/strncmp: Unbreak builds with old binutils
638caf3000 aarch64: Improve strncmp for mutually misaligned inputs
d5f45a29ff aarch64/strcmp: fix misaligned loop jump target
7f690fafad aarch64: Improve strcmp unaligned performance
40df047b3b aarch64: Fix branch target to loop16
062139f233 aarch64: Optimized memcmp for medium to large sizes
f3e2add213 aarch64: Use the L() macro for labels in memcmp
22bd3ab40e posix: Fix large mmap64 offset for mips64n32 (BZ#24699)
bdd16894aa aarch64: handle STO_AARCH64_VARIANT_PCS
0b48caab9a aarch64: add STO_AARCH64_VARIANT_PCS and DT_AARCH64_VARIANT_PCS
949da7f2fd io: Remove copy_file_range emulation [BZ #24744]
f056ac8363 libio: do not attempt to free wide buffers of legacy streams [BZ #24228]
5f90e009b1 NEWS: add entries for bugs 22964, 24180, and 24531

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
22 months agorpcd: update to latest Git HEAD
Jo-Philipp Wich [Sun, 8 Sep 2019 16:48:15 +0000 (18:48 +0200)]
rpcd: update to latest Git HEAD

69eeb1b file: refactor message parsing and permission checking
f65527a iwinfo: expose all rate info fields in assoclist reply
7fec636 sys: fix symbol redeclaration
27c24c7 rpcd: sys: actually move timespec declaration
345363b file: add remove operation
604db20 rpcd: Switch to nanosleep

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
22 months agofirewall: update to latest git HEAD
Hauke Mehrtens [Sun, 8 Sep 2019 16:37:59 +0000 (18:37 +0200)]
firewall: update to latest git HEAD

487bd0d utils: Fix string format message

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
22 months agobase-files: validate firmware for compatibility with backup
Rafał Miłecki [Thu, 5 Sep 2019 11:08:13 +0000 (13:08 +0200)]
base-files: validate firmware for compatibility with backup

This allows platform code to check if firmware image can be used with
preserving a backup. It may be used e.g. when installing vendor
firmwares that won't restore appended backup archive.

Suggested-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
22 months agofirewal: update to latest git HEAD
Hans Dedecker [Sat, 7 Sep 2019 11:17:55 +0000 (13:17 +0200)]
firewal: update to latest git HEAD

4d0c703 firewall3: Fix some format string problems
8c404ef iptables.c: lock the xtables.lock
c1d3a4d utils: implement fw3_lock_path() & fw3_unlock_path()

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
22 months agoramips: fix MAC address setup for Newifi Y1 and Y1S
Adrian Schmutzler [Fri, 16 Aug 2019 13:39:43 +0000 (15:39 +0200)]
ramips: fix MAC address setup for Newifi Y1 and Y1S

So far, MAC address setup for those devices has been using local
addresses although additional MAC addresses are available on flash.

On device, we found the following situation:
position   Y1     Y1S
0x4        *:d4   *:e4
0x8004     *:d6   *:e8
0x28       *:d4   *:e4
0x2e       *:d7   *:eb

Since 0x4 and 0x28 yield the same address, the former was set for
&ethernet in DTS. However, the typical location on this
architecture is 0x28, so this patch changes that.

For further setup in 02_network, the local bit for lan_mac is
removed, so the address from &ethernet is used at all. For wan_mac,
instead of calculating an address with local bit set, this patch
exploits the previously unused address in 0x2e.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
22 months agoramips: initialize MAC addresses from flash where possible
Adrian Schmutzler [Fri, 16 Aug 2019 10:59:09 +0000 (12:59 +0200)]
ramips: initialize MAC addresses from flash where possible

This patch changes wan MAC address setup from retrieving it by
calculation to reading it from flash.

Changes are limited to cases where on-device check was possible.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[fix mac for newifi-d1; drop adslr,g7 because it's unlikely for
vendor to specifically use 2.4g mac as wan_mac]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
22 months agoramips: fix duplicate network setup for dlink,dir-615-h1
Adrian Schmutzler [Mon, 12 Aug 2019 11:35:39 +0000 (13:35 +0200)]
ramips: fix duplicate network setup for dlink,dir-615-h1

In 555ca422d1cb ("ramips: fix D-Link DIR-615 H1 switch port
mapping"), port setup for dir-615-h1 was changed without removing
the old one. This was working as the new one was triggered earlier
than the old one.

(In the meantine, changed sorting during ramips rename patches
actually inversed that order.)

Anyway, just remove the wrong case now.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
22 months agoramips: remove duplicate case for MAC setup of freestation5
Adrian Schmutzler [Mon, 12 Aug 2019 11:31:23 +0000 (13:31 +0200)]
ramips: remove duplicate case for MAC setup of freestation5

ARC FreeStation5 is present twice in MAC address setup.

From older commits/changes, it is not possible to reconstruct
the correct choice only by reading the annotations.

Thus, remove the second case and keep the first one, so behavior
stays the same (as nobody seems to have complained about it).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
22 months agoramips: clean and improve MAC address setup in 02_network
Adrian Schmutzler [Mon, 12 Aug 2019 11:21:05 +0000 (13:21 +0200)]
ramips: clean and improve MAC address setup in 02_network

This patch removes unnecessary MAC address setup statements in
ramips' 02_network by doing several optimizations:

1. For the following devices, lan_mac was set up with
   mtd_get_mac_binary although the same address was set in DTS.
   The lan_mac statement is removed in 02_network, but
   wan_mac is kept:
   - mercury,mac1200r-v2
   - phicomm,k2g
   - skylab,skw92a
   - wiznet,wizfi630a

2. For the following devices, wan_mac was set up with
   mtd_get_mac_binary although the same address was set in DTS.
   The wan_mac statement is removed in 02_network, no
   lan_mac is present:
   - buffalo,whr-g300n
   - glinet,gl-mt300n-v2
   - zyxel,keenetic-start

3. For the following device, lan_mac and wan_mac were set up
   with mtd_get_mac_binary to the same address as set in DTS.
   Both statements are removed in 02_network:
   - buffalo,whr-600d

4. For some devices, it was possible to move setup from 02_network
   to DTS by introducing previously missing mtd_mac_address:
   - buffalo,whr-1166d
   - buffalo,whr-300hp2
   - buffalo,wsr-600dhp
   - ohyeah,oy-0001
   - planex,vr500

5. For one device, mtd_mac_address was just wrong and overwritten
   by 02_network. Put the correct value in DTS and remove redundant
   statement in 02_network:
   - asus,rt-ac57u

6. For one device, MAC address defined in DTS is exchanged together
   with lan_mac/wan_mac setup in 02_network, so that cases in
   02_network can be merged:
   - phicomm,k2p

For some devices, an empty case has to be used to prevent them
from falling into the default case and have
WAN address = eth0 address + 1 set to them.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
22 months agoRevert "build: remove harmful -nopad option from mksquashfs"
Jonas Gorski [Fri, 6 Sep 2019 12:55:36 +0000 (14:55 +0200)]
Revert "build: remove harmful -nopad option from mksquashfs"

This reverts commit 1c0290c5cc6258c48b8ba46b4f9c85a21de4f875.

Dropping the nopad can make the padding overflow into the next erase
block on devices using a non-aligned rootfs start. This breaks the jffs2
overlay partition with the following messages:

[   30.343877] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[   30.376512] jffs2: Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
[   30.385253] jffs2: empty_blocks 196, bad_blocks 0, c->nr_blocks 197

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
22 months agoodhcp6c: update to latest git HEAD
Hans Dedecker [Sat, 7 Sep 2019 11:08:27 +0000 (13:08 +0200)]
odhcp6c: update to latest git HEAD

e199804 dhcpv6: sanitize oro options

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
22 months agobcm53xx: extend firmware validation
Rafał Miłecki [Fri, 6 Sep 2019 10:44:49 +0000 (12:44 +0200)]
bcm53xx: extend firmware validation

This provides TRX validation result to the validation JSON. It also
prevents users from installing broken firmware files.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
22 months agouboot-fritz4040: build with ipq40xx "generic" subtarget
Yousong Zhou [Fri, 6 Sep 2019 08:29:50 +0000 (08:29 +0000)]
uboot-fritz4040: build with ipq40xx "generic" subtarget

Fixes: 853e4dd3 ("ipqx0xx: add Generic subtarget")
Ref: https://forum.openwrt.org/t/ipq40xx-snapshot-not-updated-since-22nd-august/44126
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
22 months agotreewide: use new procd sysupgrade $UPGRADE_BACKUP variable
Rafał Miłecki [Thu, 5 Sep 2019 21:33:19 +0000 (23:33 +0200)]
treewide: use new procd sysupgrade $UPGRADE_BACKUP variable

It's a variable set by procd that should replace hardcoded
/tmp/sysupgrade.tgz.

This change requires the most recent procd with the commit 0f3c136
("sysupgrade: set UPGRADE_BACKUP env variable").

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>