ipq40xx: add support for Linksys WHW01 v1 This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331]. Specification ------------- SOC: Qualcomm IPQ4018 WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n WiFi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8811 (A12U) Ethernet: Qualcomm QCA8072 (2-port) SPI Flash 1: Mactronix MX25L1605D (2MB) SPI Flash 2: Winbond W25M02GV (256MB) DRAM: Nanya NT5CC128M16IP-DI (256MB) LED Controller: NXP PCA963x (I2C) Buttons: Single reset button (GPIO). Notes ----- There does not appear to be a way to trigger TFTP recovery without entering U-Boot. The device must be opened to access the serial console in order to first flash OpenWrt onto a device from factory. The device has automatic recovery backed by a second set of partitions on the larger of the two SPI flash ICs. Both the primary and secondary must be flashed to prevent accidental rollback to "factory" after 3 failed boot attempts. Serial console -------------- A serial console is available on the following pins of the populated J2 connector on the device mainboard (115200 8n1). (<-- Top of PCB / Device) J2 [o o o o o o] | | | | | `-- GND | `---- TX `--------- RX Installation instructions ------------------------- 1. Setup TFTP server with server IP set to 192.168.1.236. 2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root. 3. Connect to console using pinout detailed in the serial console section. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash first partition device via `run flashimg`. 6. Once complete, reset device and allow to power up completely. 7. Once comfortable with device upgrade reboot and drop back into U-Boot. 8. Flash the second partition (recovery) via `run flashimg2`. Revert to "factory" ------------------- 1. Download latest firmware update from vendor support site. 2. Copy extracted `.img` file to `nodes-jr.img` in tftp root. 3. Connect to console using pinout detailed in the serial console section. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash first partition device via `run flashimg`. 6. Once complete, reset device and allow to power up completely. 7. Once comfortable with device upgrade reboot and drop back into U-Boot. 8. Flash the second partition (recovery) via `run flashimg2`. Signed-off-by: Peter Adkins <peter@sunkenlab.com> (calibration from nvmem, updated to 5.10+5.15) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
uboot-fritz4040: Add support for Toshiba NAND From Andreas Böhler: "Some revisions of the FRITZ!7530 use a Toshiba NAND with 8 bit ECC in contrast to the Macronix NAND with 4 bit ECC.". Uboot needs to know this in order to have a chance to load from the NAND. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
realtek: add support for ZyXEL GS1900-16 The ZyXEL GS1900-16 is a 16 port gigabit switch similar to other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-16 * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB Macronix MX25L12835F * RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8HE * Ethernet: 16x 10/100/1000 Mbps * LEDs: 1 PWR LED (green, not configurable) 1 SYS LED (green, configurable) 16 ethernet port link/activity LEDs (green, SoC controlled) * Buttons: 1 "RESET" button on front panel * Power 120-240V AC C13 * UART: 1 serial header (J12) with populated standard pin connector on the right back of the PCB. Pinout (front to back): + Pin 1 - VCC marked with white dot + Pin 2 - RX + Pin 3 - TX + PIn 4 - GND Serial connection parameters: 115200 8N1. Installation ------------ OEM upgrade method: * Log in to OEM management web interface * Navigate to Maintenance > Firmware * Select the HTTP radio button * Select the Active radio button * Use the browse button to locate the realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin file amd select open so File Path is update with filename. * Select the Apply button. Screen will display "Prepare for firmware upgrade ...". *Wait until screen shows "Do you really want to reboot?" then select the OK button * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-16 is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only boot from the first partition anyway (hardcoded in the DTS). To make sure we are manipulating the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin it may be necessary to restart the network (/etc/init.d/network restart) on the running initramfs image. Signed-off-by: Raylynn Knight <rayknight@me.com> [removed duplicate patch title, align RAM specification] Signed-off-by: Sander Vanheule <sander@svanheule.net>
ipq806x: add support for Arris TR4400 v2 / RAC2V1A Hardware specs: SoC: Qualcomm IPQ8065 (dual core Cortex-A15) RAM: 512 MB DDR3 Flash: 256 MB NAND, 32 MB NOR WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz Switch: QCA8337 Ethernet: 5x 10/100/1000 Mbit/s USB: 1x USB 3.0 Type-A Buttons: WPS, Reset Power: 12 VDC, 2.5 A Ethernet ports: 1x WAN: connected to eth2 4x LAN: connected via the switch to eth0 and eth1 (eth0 is disabled in OEM firmware) MAC addresses (OEM and OpenWrt): fw_env @ 0x00 d4:ab:82:??:??:?a LAN (eth1) fw_env @ 0x06 d4:ab:82:??:??:?b WAN (eth2) fw_env @ 0x0c d4:ab:82:??:??:?c WLAN 2.4 GHz (ath1) fw_env @ 0x12 d4:ab:82:??:??:?d WLAN 5 GHz (ath0) fw_env @ 0x18 d4:ab:82:??:??:?e OEM usage unknown (eth0 in OpenWrt) OID d4:ab:82 is registered to: ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US More info: https://openwrt.org/inbox/toh/arris/tr4400_v2 IMPORTANT: This port requires moving the 'fw_env' partition prior to first boot to consolidate 70% of the usable space in flash into a contiguous partition. 'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords. Its contents must be copied to 'rootfs_1' prior to booting via initramfs. Note that the stock 'fw_env' partition will be wiped during sysupgrade. A writable 'stock_fw_env' partition pointing to the old, stock location is included in the port to help rolling back this change if desired. Installation: - Requires serial access and a TFTP server. - Fully boot stock, press ENTER, type in: mtd erase /dev/mtd21 dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21 umount /config && ubidetach -m 23 && mtd erase /dev/mtd23 - Reboot and interrupt U-Boot by pressing a key, type in: set mtdids 'nand0=nand0' set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)' set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm' env save - Setup TFTP server serving initramfs image as 'recovery.bin', type in: set ipaddr 192.168.1.1 set serverip 192.168.1.2 tftpboot recovery.bin && bootm - Use sysupgrade to install squashfs image. This port is based on work done by AmadeusGhost <amadeus@jmu.edu.cn>. Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com> [add 5.15 changes for 0069-arm-boot-add-dts-files.patch] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
uboot-mvebu: update to version v2022.04 Release announcement: https://lore.kernel.org/u-boot/20220404143253.GQ14476@bill-the-cat/ Release notes between tags: https://source.denx.de/u-boot/u-boot/-/compare/v2022.01...v2022.04?from_project_id=531 All patches were removed, since they are included in this release. Run tested: Turris Omnia, mvebu/cortex-a9, OpenWrt daily snapshots Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
uboot-mvebu: remove enabled CONFIG_CMD_SETEXPR We don't need to make sure that we want to have enabled CONFIG_CMD_SETEXPR by default, since this is already done in U-boot [1]. This was actually needed only for clearfog board [2], which was added in commit: da0005a6d08ae33d958a6d8a6c0c12dc07b5b2b8 ("uboot-mvebu: add patch to enable setexpr for clearfog boards) and send to U-boot to fix it properly. After a while, there was added support for Turris Omnia, which uses setexpr as well [3], but for this board, there are no fixes needed in U-boot and that's why we can remove this option here. It is helpful with shell scripting. If some downstream distributions are using it, they should correct it in defconfig for related boards. [1] https://source.denx.de/u-boot/u-boot/-/blob/e95afa56753cebcd20a5114b6d121f281b789006/cmd/Kconfig#L1504 [2] https://github.com/openwrt/openwrt/blob/852126680e21edc71c0c66561ae5a6d7479dcc67/target/linux/mvebu/image/clearfog.bootscript#L7 [3] https://github.com/openwrt/openwrt/blob/852126680e21edc71c0c66561ae5a6d7479dcc67/target/linux/mvebu/image/turris-omnia.bootscript#L2 Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
uboot-mvebu: add patch to enable setexpr for clearfog boards Option CMD_SETEXPR is already default in U-boot [1], since this was disabled since initial version for this board, there is send this patch to U-boot mailing list to enable it. It is required to use in OpenWrt bootscript for these boards [2]. [1] https://source.denx.de/u-boot/u-boot/-/blob/e95afa56753cebcd20a5114b6d121f281b789006/cmd/Kconfig#L1504 [2] https://github.com/openwrt/openwrt/blob/852126680e21edc71c0c66561ae5a6d7479dcc67/target/linux/mvebu/image/clearfog.bootscript#L7 Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
ramips: add support for YunCore AX820/HWAP-AX820 There are two versions which are identical apart from the enclosure: YunCore AX820: indoor ceiling mount AP with integrated antennas YunCore HWAP-AX820: outdoor enclosure with external (N) connectors Hardware specs: SoC: MediaTek MT7621DAT Flash: 16 MiB SPI NOR RAM: 128MiB (DDR3, integrated) WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN) LED: Status (green) Button: Reset Power: 802.11af/at PoE; DC 12V,1A Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external Flash instructions: The "OpenWRT support" version of the AX820 comes with a LEDE-based firmware with proprietary MTK drivers and a luci webinterface and ssh accessible under 192.168.1.1 on LAN; user root, no password. The sysupgrade.bin can be flashed using luci or sysupgrade via ssh, you will have to force the upgrade due to a different factory name. Remember: Do *not* preserve factory configuration! MAC addresses as used by OEM firmware: use address source 2g 44:D1:FA:*:0b Factory 0x0004 (label) 5g 46:D1:FA:*:0b LAA of 2g lan 44:D1:FA:*:0c Factory 0xe000 wan 44:D1:FA:*:0d Factory 0xe000 + 1 The wan MAC can also be found in 0xe006 but is not used by OEM dtb. Due to different MAC handling in mt76 the LAA derived from lan is used for 2g to prevent duplicate MACs when creating multiple interfaces. Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
uboot-mediatek: replace patch with accepted commit Replace pending patch with version accepted upstream. Other than in the first suggested version, the new property is now called 'u-boot,bootconf' instead of 'bootconf'. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
uboot-mediatek: remove '0x' prefix from pstore node Remove '0x' prefix from pstore node in dts, just like it was done for the device tree used by Linux on MT7622. This change is done in preparation to update U-Boot to 2022.04. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
realtek: add ZyXEL GS1900-24HP v1 support The ZyXEL GS1900-24HP v1 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-24HP v1 * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB * RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM * Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps * LEDs: * 1 PWR LED (green, not configurable) * 1 SYS LED (green, configurable) * 24 ethernet port link/activity LEDs (green, SoC controlled) * 24 ethernet port PoE status LEDs * 2 SFP status/activity LEDs (green, SoC controlled) * Buttons: * 1 "RESET" button on front panel (soft reset) * 1 button ('SW1') behind right hex grate (hardwired power-off) * PoE: * Management MCU: ST Micro ST32F100 Microcontroller * 6 BCM59111 PSE chips * 170W power budget * Power: 120-240V AC C13 * UART: Internal populated 10-pin header ('J5') providing RS232; connected to SoC UART through a TI or SIPEX 3232C for voltage level shifting. * 'J5' RS232 Pinout (dot as pin 1): 2) SoC RXD 3) GND 10) SoC TXD Serial connection parameters: 115200 8N1. Installation ------------ OEM upgrade method: * Log in to OEM management web interface * Navigate to Maintenance > Firmware > Management * If "Active Image" has the first option selected, OpenWrt will need to be flashed to the "Active" partition. If the second option is selected, OpenWrt will need to be flashed to the "Backup" partition. * Navigate to Maintenance > Firmware > Upload * Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin file by your preferred method to the previously determined partition. When prompted, select to boot from the newly flashed image, and reboot the switch. * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-24HP v1 is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only be installed in the first partition anyway (hardcoded in the DTS). To ensure we are set to boot from the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin Signed-off-by: Martin Kennedy <hurricos@gmail.com> [Add info on PoE hardware to commit message] Signed-off-by: Sander Vanheule <sander@svanheule.net>
ath79: add support for Sophos AP100/AP55 family The Sophos AP100, AP100C, AP55, and AP55C are dual-band 802.11ac access points based on the Qualcomm QCA9558 SoC. They share PCB designs with several devices that already have partial or full support, most notably the Devolo DVL1750i/e. The AP100 and AP100C are hardware-identical to the AP55 and AP55C, however the 55 models' ART does not contain calibration data for their third chain despite it being present on the PCB. Specifications common to all models: - Qualcomm QCA9558 SoC @ 720 MHz (MIPS 74Kc Big-endian processor) - 128 MB RAM - 16 MB SPI flash - 1x 10/100/1000 Mbps Ethernet port, 802.3af PoE-in - Green and Red status LEDs sharing a single external light-pipe - Reset button on PCB[1] - Piezo beeper on PCB[2] - Serial UART header on PCB - Alternate power supply via 5.5x2.1mm DC jack @ 12 VDC Unique to AP100 and AP100C: - 3T3R 2.4GHz 802.11b/g/n via SoC WMAC - 3T3R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express) AP55 and AP55C: - 2T2R 2.4GHz 802.11b/g/n via SoC WMAC - 2T2R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express) AP100 and AP55: - External RJ45 serial console port[3] - USB 2.0 Type A port, power controlled via GPIO 11 Flashing instructions: This firmware can be flashed either via a compatible Sophos SG or XG firewall appliance, which does not require disassembling the device, or via the U-Boot console available on the internal UART header. To flash via XG appliance: - Register on Sophos' website for a no-cost Home Use XG firewall license - Download and install the XG software on a compatible PC or virtual machine, complete initial appliance setup, and enable SSH console access - Connect the target AP device to the XG appliance's LAN interface - Approve the AP from the XG Web UI and wait until it shows as Active (this can take 3-5 minutes) - Connect to the XG appliance over SSH and access the Advanced Console (Menu option 5, then menu option 3) - Run `sudo awetool` and select the menu option to connect to an AP via SSH. When prompted to enable SSH on the target AP, select Yes. - Wait 2-3 minutes, then select the AP from the awetool menu again. This will connect you to a root shell on the target AP. - Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc - Run `mtd -r write /tmp/openwrt.bin astaro_image` - When complete, the access point will reboot to OpenWRT. To flash via U-Boot serial console: - Configure a TFTP server on your PC, and set IP address 192.168.99.8 with netmask 255.255.255.0 - Copy the firmware .bin to the TFTP server and rename to 'uImage_AP100C' - Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4] - Connect the AP ethernet to your PC's ethernet port - Connect a terminal to the UART at 115200 8/N/1 as usual - Power on the AP and press a key to cancel autoboot when prompted - Run the following commands at the U-Boot console: - `tftpboot` - `cp.b $fileaddr 0x9f070000 $filesize` - `boot` - The access point will boot to OpenWRT. MAC addresses as verified by OEM firmware: use address source LAN label config 0x201a (label) 2g label + 1 art 0x1002 (also found at config 0x2004) 5g label + 9 art 0x5006 Increments confirmed across three AP55C, two AP55, and one AP100C. These changes have been tested to function on both current master and 21.02.0 without any obvious issues. [1] Button is present but does not alter state of any GPIO on SoC [2] Buzzer and driver circuitry is present on PCB but is not connected to any GPIO. Shorting an unpopulated resistor next to the driver circuitry should connect the buzzer to GPIO 4, but this is unconfirmed. [3] This external RJ45 serial port is disabled in the OEM firmware, but works in OpenWRT without additional configuration, at least on my three test units. [4] On AP100/AP55 models the UART header is accessible after removing the device's top cover. On AP100C/AP55C models, the PCB must be removed for access; three screws secure it to the case. Pin 1 is marked on the silkscreen. Pins from 1-4 are 3.3V, GND, TX, RX Signed-off-by: Andrew Powers-Holmes <andrew@omnom.net>
ramips: add support for BOLT! Arion This device is from now-defunct BOLT! ISP in Indonesia. The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision. Specifications: - SoC: MediaTek MT7621 - Flash: 32 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 2x internal, non-detachable - LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1) Non-programmable "Power" LED - Buttons: Reset and WPS Instalation: Install from TFTP Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123 Press "1" when turning on the router, and type the initramfs file name You also need to solder pin header or cable to J4 or neighboring test points (T19-T21) Pinouts from top to bottom: GND, TX, RX, VCC (3.3v) Baudrate: 57600n8 There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB. Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com>
ath79: add support for Yuncore A930 Specification: - QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR - 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN) - 2T2R 802.11b/g/n 2.4GHz Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
ath79: add support for Yuncore XD3200 Specification: - QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR - 2T2R 802.11b/g/n 2.4GHz - 2T2R 802.11n/ac 5GHz - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) LED for 5 GHz WLAN is currently not supported as it is connected directly to the QCA9882 radio chip. Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
arm-trusted-firmware-mediatek: remove no longer needed Configure step As anyway only the default is called now we can as well also just remove the override for Build/Configure. Fixes: e2cffbb805 ("arm-trusted-firmware-mediatek: update to 2021-03-10") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
uboot-imx: bump to 2022.01 release Two patches were removed because of the changes introduced in upstream: 1. 110-mx6cuboxi-mmc-fallback.patch Looks like similar changes were introduced in 6c3fbf3e456c ("mx6cuboxi: customize board_boot_order to access eMMC"). 2. 111-mx6cuboxi_defconfig-force-mmc-boot.patch The 'CONFIG_SPL_FORCE_MMC_BOOT' was removed in 15aec318ef03 ("Revert "imx: Introduce CONFIG_SPL_FORCE_MMC_BOOT to force MMC boot on falcon mode"). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>