target/linux/ipq40xx/image/Makefile

   1 include $(TOPDIR)/rules.mk
   2 include $(INCLUDE_DIR)/image.mk
   3
   4 DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION
   5
   6 define Device/Default
   7         PROFILES := Default
   8         KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
   9         KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
  10         KERNEL_PREFIX := $$(IMAGE_PREFIX)
  11         KERNEL_LOADADDR := 0x80208000
  12         SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
  13         IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata
  14         IMAGE/sysupgrade.bin/squashfs :=
  15 endef
  16
  17 define Device/FitImage
  18         KERNEL_SUFFIX := -fit-uImage.itb
  19         KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
  20         KERNEL_NAME := Image
  21 endef
  22
  23 define Device/FitImageLzma
  24         KERNEL_SUFFIX := -fit-uImage.itb
  25         KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
  26         KERNEL_NAME := Image
  27 endef
  28
  29 define Device/FitzImage
  30         KERNEL_SUFFIX := -fit-zImage.itb
  31         KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb
  32         KERNEL_NAME := zImage
  33 endef
  34
  35 define Device/UbiFit
  36         KERNEL_IN_UBI := 1
  37         IMAGES := nand-factory.ubi nand-sysupgrade.bin
  38         IMAGE/nand-factory.ubi := append-ubi
  39         IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
  40 endef
  41
  42 define Device/DniImage
  43         KERNEL_SUFFIX := -fit-uImage.itb
  44         KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
  45         KERNEL_NAME := Image
  46         NETGEAR_BOARD_ID :=
  47         NETGEAR_HW_ID :=
  48         IMAGES := factory.img sysupgrade.bin
  49         IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | netgear-dni
  50         IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | append-metadata
  51 endef
  52 DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
  53
  54 define Build/SenaoFW
  55         -$(STAGING_DIR_HOST)/bin/mksenaofw \
  56                 -n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \
  57                 -c $(DATECODE) -w $(2) -x $(CW_VER) -t 0 \
  58                 -e $@ \
  59                 -o $@.new
  60         @cp $@.new $@
  61 endef
  62
  63 define Device/8dev_jalapeno
  64         $(call Device/FitImage)
  65         $(call Device/UbiFit)
  66         DEVICE_VENDOR := 8devices
  67         DEVICE_MODEL := Jalapeno
  68         DEVICE_DTS := qcom-ipq4018-jalapeno
  69         BLOCKSIZE := 128k
  70         PAGESIZE := 2048
  71 endef
  72 TARGET_DEVICES += 8dev_jalapeno
  73
  74 define Device/alfa-network_ap120c-ac
  75         $(call Device/FitImage)
  76         $(call Device/UbiFit)
  77         DEVICE_VENDOR := ALFA Network
  78         DEVICE_MODEL := AP120C-AC
  79         DEVICE_DTS := qcom-ipq4018-ap120c-ac
  80         DEVICE_PACKAGES := kmod-usb-acm \
  81                 kmod-tpm-i2c-atmel uboot-envtools
  82         BLOCKSIZE := 128k
  83         PAGESIZE := 2048
  84         IMAGE_SIZE := 65536k
  85         IMAGES := nand-factory.bin nand-sysupgrade.bin
  86         IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
  87 endef
  88 TARGET_DEVICES += alfa-network_ap120c-ac
  89
  90 define Device/asus_map-ac2200
  91         $(call Device/FitImageLzma)
  92         DEVICE_VENDOR := ASUS
  93         DEVICE_MODEL := Lyra (MAP-AC2200)
  94         DEVICE_DTS := qcom-ipq4019-map-ac2200
  95         IMAGES := sysupgrade.bin
  96         DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-ath3k
  97 endef
  98 TARGET_DEVICES += asus_map-ac2200
  99
 100 define Device/asus_rt-ac58u
 101         $(call Device/FitImageLzma)
 102         DEVICE_VENDOR := ASUS
 103         DEVICE_MODEL := RT-AC58U
 104         DEVICE_DTS := qcom-ipq4018-rt-ac58u
 105         BLOCKSIZE := 128k
 106         PAGESIZE := 2048
 107         DTB_SIZE := 65536
 108         IMAGE_SIZE := 20439364
 109         FILESYSTEMS := squashfs
 110 #       Someone - in their infinite wisdom - decided to put the firmware
 111 #       version in front of the image name \03\00\00\04 => Version 3.0.0.4
 112 #       Since u-boot works with strings we either need another fixup step
 113 #       to add a version... or we are very careful not to add '\0' into that
 114 #       string and call it a day.... Yeah, we do the latter!
 115         UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U')
 116         IMAGES := sysupgrade.bin
 117         DEVICE_PACKAGES := kmod-usb-ledtrig-usbport
 118 endef
 119 TARGET_DEVICES += asus_rt-ac58u
 120
 121 define Device/avm_fritzbox-4040
 122         $(call Device/FitImageLzma)
 123         DEVICE_VENDOR := AVM
 124         DEVICE_MODEL := FRITZ!Box 4040
 125         DEVICE_DTS := qcom-ipq4018-fritz4040
 126         BOARD_NAME := fritz4040
 127         IMAGE_SIZE := 29753344
 128         UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin
 129         UBOOT_PARTITION_SIZE := 524288
 130         IMAGES = eva.bin sysupgrade.bin
 131         IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs
 132         IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
 133         DEVICE_PACKAGES := fritz-tffs fritz-caldata
 134 endef
 135 TARGET_DEVICES += avm_fritzbox-4040
 136
 137 define Device/avm_fritzbox-7530
 138         $(call Device/FitImageLzma)
 139         DEVICE_VENDOR := AVM
 140         DEVICE_MODEL := FRITZ!Box 7530
 141         DEVICE_DTS := qcom-ipq4019-fritzbox-7530
 142         DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand
 143         IMAGES := sysupgrade.bin
 144 endef
 145 TARGET_DEVICES += avm_fritzbox-7530
 146
 147 define Device/avm_fritzrepeater-3000
 148         $(call Device/FitImageLzma)
 149         DEVICE_VENDOR := AVM
 150         DEVICE_MODEL := FRITZ!Repeater 3000
 151         DEVICE_DTS := qcom-ipq4019-fritzrepeater-3000
 152         DEVICE_PACKAGES := ath10k-firmware-qca9984-ct fritz-caldata fritz-tffs-nand
 153         IMAGES := sysupgrade.bin
 154 endef
 155 TARGET_DEVICES += avm_fritzrepeater-3000
 156
 157 define Device/compex_wpj428
 158         $(call Device/FitImage)
 159         DEVICE_VENDOR := Compex
 160         DEVICE_MODEL := WPJ428
 161         DEVICE_DTS := qcom-ipq4028-wpj428
 162         DEVICE_DTS_CONFIG := config@4
 163         BLOCKSIZE := 64k
 164         IMAGE_SIZE := 31232k
 165         KERNEL_SIZE := 4096k
 166         IMAGES = sysupgrade.bin
 167         IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
 168         DEVICE_PACKAGES := kmod-gpio-beeper
 169 endef
 170 TARGET_DEVICES += compex_wpj428
 171
 172 define Device/engenius_eap1300
 173         $(call Device/FitImage)
 174         DEVICE_VENDOR := EnGenius
 175         DEVICE_MODEL := EAP1300
 176         DEVICE_DTS_CONFIG := config@4
 177         BOARD_NAME := eap1300
 178         DEVICE_DTS := qcom-ipq4018-eap1300
 179         KERNEL_SIZE := 5120k
 180         IMAGE_SIZE := 25344k
 181         IMAGES := sysupgrade.bin
 182         IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
 183 endef
 184 TARGET_DEVICES += engenius_eap1300
 185
 186 define Device/engenius_ens620ext
 187         $(call Device/FitImage)
 188         DEVICE_VENDOR := EnGenius
 189         DEVICE_MODEL := ENS620EXT
 190         DEVICE_DTS := qcom-ipq4018-ens620ext
 191         DEVICE_DTS_CONFIG := config@4
 192         BLOCKSIZE := 64k
 193         PAGESIZE := 256
 194         BOARD_NAME := ENS620EXT
 195         VENDOR_ID := 0x0101
 196         PRODUCT_ID := 0x79
 197         PRODUCT_ID_NEW := 0xA4
 198         DATECODE := 190507
 199         FW_VER := 3.1.2
 200         FW_VER_NEW := 3.5.6
 201         CW_VER := 1.8.99
 202         IMAGE_SIZE := 21823488
 203         KERNEL_SIZE := 5120k
 204         FILESYSTEMS := squashfs
 205         IMAGES := sysupgrade.bin factory_30.bin factory_35.bin
 206         IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | append-metadata
 207         IMAGE/factory_30.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | SenaoFW $$$$(PRODUCT_ID) $$$$(FW_VER)
 208         IMAGE/factory_35.bin := qsdk-ipq-factory-nor | check-size $$$$(IMAGE_SIZE) | SenaoFW $$$$(PRODUCT_ID_NEW) $$$$(FW_VER_NEW)
 209 endef
 210 TARGET_DEVICES += engenius_ens620ext
 211
 212 define Device/glinet_gl-b1300
 213         $(call Device/FitImage)
 214         DEVICE_VENDOR := GL.iNet
 215         DEVICE_MODEL := GL-B1300
 216         BOARD_NAME := gl-b1300
 217         DEVICE_DTS := qcom-ipq4029-gl-b1300
 218         KERNEL_SIZE := 4096k
 219         IMAGE_SIZE := 26624k
 220         IMAGES := sysupgrade.bin
 221         IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata
 222 endef
 223 TARGET_DEVICES += glinet_gl-b1300
 224
 225 define Device/linksys_ea6350v3
 226         # The Linksys EA6350v3 has a uboot bootloader that does not
 227         # support either booting lzma kernel images nor booting UBI
 228         # partitions. This uboot, however, supports raw kernel images and
 229         # gzipped images.
 230         #
 231         # As for the time of writing this, the device will boot the kernel
 232         # from a fixed address with a fixed length of 3MiB. Also, the
 233         # device has a hard-coded kernel command line that requieres the
 234         # rootfs and alt_rootfs to be in mtd11 and mtd13 respectively.
 235         # Oh... and the kernel partition overlaps with the rootfs
 236         # partition (the same for alt_kernel and alt_rootfs).
 237         #
 238         # If you are planing re-partitioning the device, you may want to
 239         # keep those details in mind:
 240         # 1. The kernel adresses you should honor are 0x00000000 and
 241         #    0x02800000 respectively.
 242         # 2. The kernel size (plus the dtb) cannot exceed 3.00MiB in size.
 243         # 3. You can use 'zImage', but not a raw 'Image' packed with lzma.
 244         # 4. The kernel command line from uboot is harcoded to boot with
 245         #    rootfs either in mtd11 or mtd13.
 246         $(call Device/FitzImage)
 247         DEVICE_VENDOR := Linksys
 248         DEVICE_MODEL := EA6350
 249         DEVICE_VARIANT := v3
 250         DEVICE_DTS := qcom-ipq4018-ea6350v3
 251         BLOCKSIZE := 128k
 252         PAGESIZE := 2048
 253         KERNEL_SIZE := 3145728
 254         IMAGE_SIZE := 38797312
 255         UBINIZE_OPTS := -E 5
 256         IMAGES := factory.bin sysupgrade.bin
 257         IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$${KERNEL_SIZE} | append-ubi | linksys-image type=EA6350v3
 258         DEVICE_PACKAGES := uboot-envtools
 259 endef
 260 TARGET_DEVICES += linksys_ea6350v3
 261
 262 define Device/linksys_ea8300
 263         $(call Device/FitzImage)
 264         DEVICE_VENDOR := Linksys
 265         DEVICE_MODEL := EA8300
 266         DEVICE_DTS := qcom-ipq4019-linksys_ea8300
 267         KERNEL_SIZE := 3072k
 268         IMAGE_SIZE := 87040k
 269         BLOCKSIZE := 128k
 270         PAGESIZE := 2048
 271         UBINIZE_OPTS := -E 5    # EOD marks to "hide" factory sig at EOF
 272         IMAGES := sysupgrade.bin factory.bin
 273         IMAGE/factory.bin  := append-kernel | pad-to $$$${KERNEL_SIZE} | append-ubi | linksys-image type=EA8300
 274         DEVICE_PACKAGES := uboot-envtools ath10k-firmware-qca9888-ct ipq-wifi-linksys_ea8300 kmod-usb-ledtrig-usbport
 275 endef
 276 TARGET_DEVICES += linksys_ea8300
 277
 278 define Device/meraki_mr33
 279         $(call Device/FitImage)
 280         DEVICE_VENDOR := Cisco Meraki
 281         DEVICE_MODEL := MR33
 282         DEVICE_DTS := qcom-ipq4029-mr33
 283         BLOCKSIZE := 131072
 284         PAGESIZE := 2048
 285         IMAGES = sysupgrade.bin
 286         DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct
 287 endef
 288 TARGET_DEVICES += meraki_mr33
 289
 290 define Device/netgear_ex61x0v2
 291         $(call Device/DniImage)
 292         DEVICE_DTS_CONFIG := config@4
 293         NETGEAR_BOARD_ID := EX6150v2series
 294         NETGEAR_HW_ID := 29765285+16+0+128+2x2
 295 endef
 296
 297 define Device/netgear_ex6100v2
 298         $(call Device/netgear_ex61x0v2)
 299         DEVICE_VENDOR := Netgear
 300         DEVICE_MODEL := EX6100
 301         DEVICE_VARIANT := v2
 302         DEVICE_DTS := qcom-ipq4018-ex6100v2
 303 endef
 304 TARGET_DEVICES += netgear_ex6100v2
 305
 306 define Device/netgear_ex6150v2
 307         $(call Device/netgear_ex61x0v2)
 308         DEVICE_VENDOR := Netgear
 309         DEVICE_MODEL := EX6150
 310         DEVICE_VARIANT := v2
 311         DEVICE_DTS := qcom-ipq4018-ex6150v2
 312 endef
 313 TARGET_DEVICES += netgear_ex6150v2
 314
 315 define Device/openmesh_a42
 316         $(call Device/FitImageLzma)
 317         DEVICE_VENDOR := OpenMesh
 318         DEVICE_MODEL := A42
 319         DEVICE_DTS := qcom-ipq4018-a42
 320         DEVICE_DTS_CONFIG := config@om.a42
 321         BLOCKSIZE := 64k
 322         KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
 323         IMAGE_SIZE := 15616k
 324         IMAGES = factory.bin sysupgrade.bin
 325         IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
 326         IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
 327         DEVICE_PACKAGES := uboot-envtools
 328 endef
 329 TARGET_DEVICES += openmesh_a42
 330
 331 define Device/openmesh_a62
 332         $(call Device/FitImageLzma)
 333         DEVICE_VENDOR := OpenMesh
 334         DEVICE_MODEL := A62
 335         DEVICE_DTS := qcom-ipq4019-a62
 336         DEVICE_DTS_CONFIG := config@om.a62
 337         BLOCKSIZE := 64k
 338         KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
 339         IMAGE_SIZE := 15552k
 340         IMAGES = factory.bin sysupgrade.bin
 341         IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62
 342         IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
 343         DEVICE_PACKAGES := ath10k-firmware-qca9888-ct uboot-envtools
 344 endef
 345
 346 TARGET_DEVICES += openmesh_a62
 347
 348 define Device/qcom_ap-dk01.1-c1
 349         DEVICE_VENDOR := Qualcomm Atheros
 350         DEVICE_MODEL := AP-DK01.1
 351         DEVICE_VARIANT := C1
 352         BOARD_NAME := ap-dk01.1-c1
 353         DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
 354         KERNEL_INSTALL := 1
 355         KERNEL_SIZE := 4096k
 356         IMAGE_SIZE := 26624k
 357         $(call Device/FitImage)
 358         IMAGES := sysupgrade.bin
 359         IMAGE/sysupgrade.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
 360 endef
 361 TARGET_DEVICES += qcom_ap-dk01.1-c1
 362
 363 define Device/qcom_ap-dk04.1-c1
 364         $(call Device/FitImage)
 365         $(call Device/UbiFit)
 366         DEVICE_VENDOR := Qualcomm Atheros
 367         DEVICE_MODEL := AP-DK04.1
 368         DEVICE_VARIANT := C1
 369         DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
 370         KERNEL_INSTALL := 1
 371         KERNEL_SIZE := 4048k
 372         BLOCKSIZE := 128k
 373         PAGESIZE := 2048
 374         BOARD_NAME := ap-dk04.1-c1
 375 endef
 376 TARGET_DEVICES += qcom_ap-dk04.1-c1
 377
 378 define Device/qxwlan_e2600ac-c1
 379         $(call Device/FitImage)
 380         DEVICE_VENDOR := Qxwlan
 381         DEVICE_MODEL := E2600AC
 382         DEVICE_VARIANT := C1
 383         BOARD_NAME := e2600ac-c1
 384         DEVICE_DTS := qcom-ipq4019-qxwlan-e2600ac-c1
 385         KERNEL_SIZE := 4096k
 386         IMAGE_SIZE := 31232k
 387         IMAGES := sysupgrade.bin
 388         IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
 389         DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
 390 endef
 391 TARGET_DEVICES += qxwlan_e2600ac-c1
 392
 393 define Device/qxwlan_e2600ac-c2
 394         $(call Device/FitImage)
 395         $(call Device/UbiFit)
 396         DEVICE_VENDOR := Qxwlan
 397         DEVICE_MODEL := E2600AC
 398         DEVICE_VARIANT := C2
 399         DEVICE_DTS := qcom-ipq4019-qxwlan-e2600ac-c2
 400         KERNEL_INSTALL := 1
 401         BLOCKSIZE := 128k
 402         PAGESIZE := 2048
 403         DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac
 404 endef
 405 TARGET_DEVICES += qxwlan_e2600ac-c2
 406
 407 define Device/zyxel_nbg6617
 408         $(call Device/FitImageLzma)
 409         DEVICE_VENDOR := ZyXEL
 410         DEVICE_MODEL := NBG6617
 411         DEVICE_DTS := qcom-ipq4018-nbg6617
 412         ROOTFS_SIZE := 24960k
 413         RAS_BOARD := NBG6617
 414         RAS_ROOTFS_SIZE := 19840k
 415         RAS_VERSION := "$(VERSION_DIST) $(REVISION)"
 416         IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
 417         IMAGES := sysupgrade.bin factory.bin
 418 #       The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is
 419 #       at least as large as the one of the initial firmware image (not the current
 420 #       one on the device). This only applies to the Web-UI, the bootlaoder ignores
 421 #       this minimum-size. However, the larger image can be flashed both ways.
 422         IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k | check-size $$$$(ROOTFS_SIZE) | zyxel-ras-image separate-kernel
 423         IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata
 424         DEVICE_PACKAGES := uboot-envtools kmod-usb-ledtrig-usbport
 425 endef
 426 TARGET_DEVICES += zyxel_nbg6617
 427
 428 define Device/zyxel_wre6606
 429         $(call Device/FitImage)
 430         DEVICE_VENDOR := ZyXEL
 431         DEVICE_MODEL := WRE6606
 432         DEVICE_DTS_CONFIG := config@4
 433         DEVICE_DTS := qcom-ipq4018-wre6606
 434         IMAGES := sysupgrade.bin
 435         IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
 436 endef
 437 TARGET_DEVICES += zyxel_wre6606
 438
 439 $(eval $(call BuildImage))