proto_config_add_int profile
proto_config_add_boolean dhcpv6
proto_config_add_boolean autoconnect
+ proto_config_add_int plmn
proto_config_add_defaults
}
proto_qmi_setup() {
local interface="$1"
-
- local device apn auth username password pincode delay modes pdptype profile dhcpv6 autoconnect $PROTO_DEFAULT_OPTIONS
+ local dataformat
+ local device apn auth username password pincode delay modes pdptype profile dhcpv6 autoconnect plmn $PROTO_DEFAULT_OPTIONS
local cid_4 pdh_4 cid_6 pdh_6
local ip_6 ip_prefix_length gateway_6 dns1_6 dns2_6
- json_get_vars device apn auth username password pincode delay modes pdptype profile dhcpv6 autoconnect $PROTO_DEFAULT_OPTIONS
+ json_get_vars device apn auth username password pincode delay modes pdptype profile dhcpv6 autoconnect plmn $PROTO_DEFAULT_OPTIONS
[ "$metric" = "" ] && metric="0"
proto_set_available "$interface" 0
return 1
}
+
+ device="$(readlink -f $device)"
[ -c "$device" ] || {
echo "The specified control device does not exist"
proto_notify_error "$interface" NO_DEVICE
[ -n "$delay" ] && sleep "$delay"
while uqmi -s -d "$device" --get-pin-status | grep '"UIM uninitialized"' > /dev/null; do
+ [ -e "$device" ] || return 1
sleep 1;
done
[ -n "$pincode" ] && {
- uqmi -s -d "$device" --verify-pin1 "$pincode" || {
+ uqmi -s -d "$device" --verify-pin1 "$pincode" > /dev/null || uqmi -s -d "$device" --uim-verify-pin1 "$pincode" > /dev/null || {
echo "Unable to verify PIN"
proto_notify_error "$interface" PIN_FAILED
proto_block_restart "$interface"
}
}
+ [ -n "$plmn" ] && {
+ local mcc mnc
+ if [ "$plmn" = 0 ]; then
+ mcc=0
+ mnc=0
+ echo "Setting PLMN to auto"
+ else
+ mcc=${plmn:0:3}
+ mnc=${plmn:3}
+ echo "Setting PLMN to $plmn"
+ fi
+ uqmi -s -d "$device" --set-plmn --mcc "$mcc" --mnc "$mnc" || {
+ echo "Unable to set PLMN"
+ proto_notify_error "$interface" PLMN_FAILED
+ proto_block_restart "$interface"
+ return 1
+ }
+ }
+
+ # Cleanup current state if any
+ uqmi -s -d "$device" --stop-network 0xffffffff --autoconnect
+
+ # Set IP format
uqmi -s -d "$device" --set-data-format 802.3
uqmi -s -d "$device" --wda-set-data-format 802.3
+ dataformat="$(uqmi -s -d "$device" --wda-get-data-format)"
+
+ if [ "$dataformat" = '"raw-ip"' ]; then
+
+ [ -f /sys/class/net/$ifname/qmi/raw_ip ] || {
+ echo "Device only supports raw-ip mode but is missing this required driver attribute: /sys/class/net/$ifname/qmi/raw_ip"
+ return 1
+ }
+
+ echo "Device does not support 802.3 mode. Informing driver of raw-ip only for $ifname .."
+ echo "Y" > /sys/class/net/$ifname/qmi/raw_ip
+ fi
+
+ uqmi -s -d "$device" --sync
echo "Waiting for network registration"
while uqmi -s -d "$device" --get-serving-system | grep '"searching"' > /dev/null; do
+ [ -e "$device" ] || return 1
sleep 5;
done
echo "Starting network $interface"
- pdptype=`echo "$pdptype" | awk '{print tolower($0)}'`
+ pdptype=$(echo "$pdptype" | awk '{print tolower($0)}')
[ "$pdptype" = "ip" -o "$pdptype" = "ipv6" -o "$pdptype" = "ipv4v6" ] || pdptype="ip"
if [ "$pdptype" = "ip" ]; then
fi
[ "$pdptype" = "ip" -o "$pdptype" = "ipv4v6" ] && {
- cid_4=`uqmi -s -d "$device" --get-client-id wds`
+ cid_4=$(uqmi -s -d "$device" --get-client-id wds)
[ $? -ne 0 ] && {
echo "Unable to obtain client ID"
proto_notify_error "$interface" NO_CID
uqmi -s -d "$device" --set-client-id wds,"$cid_4" --set-ip-family ipv4 > /dev/null
- # try to clear previous autoconnect state
- uqmi -s -d "$device" --set-client-id wds,"$cid_4" \
- --stop-network 0xffffffff \
- --autoconnect > /dev/null
-
- pdh_4=`uqmi -s -d "$device" --set-client-id wds,"$cid_4" \
+ pdh_4=$(uqmi -s -d "$device" --set-client-id wds,"$cid_4" \
--start-network \
${apn:+--apn $apn} \
${profile:+--profile $profile} \
${auth:+--auth-type $auth} \
${username:+--username $username} \
${password:+--password $password} \
- ${autoconnect:+--autoconnect}`
+ ${autoconnect:+--autoconnect})
[ $? -ne 0 ] && {
echo "Unable to connect IPv4"
uqmi -s -d "$device" --set-client-id wds,"$cid_4" --release-client-id wds
}
[ "$pdptype" = "ipv6" -o "$pdptype" = "ipv4v6" ] && {
- cid_6=`uqmi -s -d "$device" --get-client-id wds`
+ cid_6=$(uqmi -s -d "$device" --get-client-id wds)
[ $? -ne 0 ] && {
echo "Unable to obtain client ID"
proto_notify_error "$interface" NO_CID
uqmi -s -d "$device" --set-client-id wds,"$cid_6" --set-ip-family ipv6 > /dev/null
- # try to clear previous autoconnect state
- uqmi -s -d "$device" --set-client-id wds,"$cid_6" \
- --stop-network 0xffffffff \
- --autoconnect > /dev/null
-
- pdh_6=`uqmi -s -d "$device" --set-client-id wds,"$cid_6" \
+ pdh_6=$(uqmi -s -d "$device" --set-client-id wds,"$cid_6" \
--start-network \
${apn:+--apn $apn} \
${profile:+--profile $profile} \
${auth:+--auth-type $auth} \
${username:+--username $username} \
${password:+--password $password} \
- ${autoconnect:+--autoconnect}`
+ ${autoconnect:+--autoconnect})
[ $? -ne 0 ] && {
echo "Unable to connect IPv6"
uqmi -s -d "$device" --set-client-id wds,"$cid_6" --release-client-id wds