board=$(board_name)
+board2_add_entry()
+{
+ local file="$1"
+ local offset="$(($2))"
+ local size="$(($3))"
+
+ local id=$(dd iflag=skip_bytes if="$file" bs=1 count=1 skip=$((offset+32)) | hexdump -e '1/1 "%02d"')
+
+ # Qualcomm IDs are in the range of 16 to 30 it seems - taken from the board-2.bin
+ # This is there to skip the missing 2G on the SXTSQ 5 AC
+ [ "$id" -ge 16 -a "$id" -le 30 ] || return 0
+
+ printf "\x00\x00\x00\x00\x58\x2f\x00\x00\x00\x00\x00\x00\x25\x00\x00\x00"
+ printf "bus=ahb,bmi-chip-id=0,bmi-board-id=${id}\x00\x00\x00"
+ printf "\x01\x00\x00\x00\x20\x2f\x00\x00"
+
+ dd iflag=skip_bytes,fullblock if="$file" bs="$size" count=1 skip="$offset" >> "/lib/firmware/$FIRMWARE"
+}
+
+board2_create_for_mikrotik()
+{
+ wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data"
+
+ [ -f "$wlan_data" ] && {
+ (
+ printf "QCA-ATH10K-BOARD\x00\x00\x00\x00"
+ board2_add_entry "$wlan_data" 0x2f20 0x2f20
+ board2_add_entry "$wlan_data" 0xaf20 0x2f20
+ ) >> "/lib/firmware/$FIRMWARE"
+ } || true
+
+ [ -d "$wlan_data" ] && {
+ (
+ printf "QCA-ATH10K-BOARD\x00\x00\x00\x00"
+ board2_add_entry "$wlan_data/data_0" 0x2f20 0x2f20
+ board2_add_entry "$wlan_data/data_2" 0x2f20 0x2f20
+ ) >> "/lib/firmware/$FIRMWARE"
+ } || true
+}
+
case "$FIRMWARE" in
"ath10k/cal-pci-0000:01:00.0.bin")
case "$board" in
meraki,mr33)
caldata_extract_ubi "ART" 0x9000 0x844
caldata_valid "4408" || caldata_extract "ART" 0x9000 0x844
- ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) +1)
+ ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) 1)
;;
esac
;;
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
+ asus,rt-ac42u)
+ caldata_extract_ubi "Factory" 0x9000 0x2f20
+ ;;
avm,fritzrepeater-3000)
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
;;
- buffalo,wtr-m2133hp)
- caldata_extract "ART" 0x9000 0x2f20
- ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x32)
- ;;
- engenius,eap2200 |\
- openmesh,a62)
+ openmesh,a62 |\
+ plasmacloud,pa2200)
caldata_extract "0:ART" 0x9000 0x2f20
;;
- linksys,ea8300)
+ linksys,ea8300 |\
+ linksys,mr8300)
caldata_extract "ART" 0x9000 0x2f20
# OEM assigns 4 sequential MACs
ath10k_patch_mac $(macaddr_setbit_la $(macaddr_add "$(cat /sys/class/net/eth0/address)" 4))
;;
+ netgear,rbr50|\
+ netgear,rbs50|\
+ netgear,srr60|\
+ netgear,srs60)
+ caldata_extract_mmc "0:ART" 0x9000 0x2f20
+ ath10k_patch_mac $(mmc_get_mac_binary ARTMTD 0x12)
+ ;;
esac
;;
"ath10k/pre-cal-ahb-a000000.wifi.bin")
case "$board" in
- 8dev,habanero-dvk |\
- 8dev,jalapeno |\
- alfa-network,ap120c-ac |\
- cilab,meshpoint-one |\
- ezviz,cs-w3-wd1200g-eup |\
- glinet,gl-b1300 |\
- glinet,gl-s1300 |\
- linksys,ea6350v3 |\
- mobipromo,cm520-79f |\
qcom,ap-dk01.1-c1)
caldata_extract "ART" 0x1000 0x2f20
;;
- aruba,ap-303 |\
- aruba,ap-303h |\
- aruba,ap-365)
- caldata_extract "ART" 0x1000 0x2f20
- ath10k_patch_mac $(mtd_get_mac_binary mfginfo 0x1D)
- ;;
- asus,map-ac2200)
- caldata_extract_ubi "Factory" 0x1000 0x2f20
- ;;
+ asus,map-ac2200|\
+ asus,rt-ac42u|\
asus,rt-ac58u)
- CI_UBIPART=UBI_DEV
caldata_extract_ubi "Factory" 0x1000 0x2f20
;;
avm,fritzbox-4040)
/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
;;
- buffalo,wtr-m2133hp)
- caldata_extract "ART" 0x1000 0x2f20
- ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x26)
- ;;
- cellc,rtl30vw |\
- compex,wpj419 |\
- compex,wpj428 |\
- edgecore,ecw5211 |\
- edgecore,oap100 |\
- engenius,eap1300 |\
- engenius,eap2200 |\
- luma,wrtq-329acn|\
openmesh,a42 |\
openmesh,a62 |\
- qxwlan,e2600ac-c1 |\
- qxwlan,e2600ac-c2 |\
- unielec,u4019-32m)
+ plasmacloud,pa1200 |\
+ plasmacloud,pa2200)
caldata_extract "0:ART" 0x1000 0x2f20
;;
+ devolo,magic-2-wifi-next)
+ caldata_extract "ART" 0x1000 0x2f20
+ ath10k_patch_mac $(mtd_get_mac_ascii APPSBLENV WiFiMacAddress0)
+ ;;
dlink,dap-2610)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac)
;;
engenius,ens620ext)
caldata_extract "ART" 0x1000 0x2f20
- ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +2)
+ ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) 2)
;;
- linksys,ea8300)
+ linksys,ea8300 |\
+ linksys,mr8300)
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 2)
;;
meraki,mr33)
caldata_extract_ubi "ART" 0x1000 0x2f20
caldata_valid "202f" || caldata_extract "ART" 0x1000 0x2f20
- ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) +2)
- ;;
- netgear,ex6100v2 |\
- netgear,ex6150v2)
- caldata_extract "ART" 0x1000 0x2f20
- ath10k_patch_mac $(mtd_get_mac_binary dnidata 0x0)
+ ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) 2)
+ ;;
+ mikrotik,cap-ac |\
+ mikrotik,hap-ac2 |\
+ mikrotik,hap-ac3)
+ wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data"
+ ( [ -f "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data" 0x0 0x2f20 ) || \
+ ( [ -d "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data/data_0" 0x0 0x2f20 )
+ ;;
+ netgear,rbr50|\
+ netgear,rbs50|\
+ netgear,srr60|\
+ netgear,srs60)
+ caldata_extract_mmc "0:ART" 0x1000 0x2f20
+ ath10k_patch_mac $(mmc_get_mac_binary ARTMTD 0x0)
;;
zyxel,nbg6617 |\
zyxel,wre6606)
;;
"ath10k/pre-cal-ahb-a800000.wifi.bin")
case "$board" in
- 8dev,habanero-dvk |\
- 8dev,jalapeno |\
- alfa-network,ap120c-ac |\
- cilab,meshpoint-one |\
- ezviz,cs-w3-wd1200g-eup |\
- glinet,gl-b1300 |\
- glinet,gl-s1300 |\
- linksys,ea6350v3 |\
- mobipromo,cm520-79f |\
qcom,ap-dk01.1-c1)
caldata_extract "ART" 0x5000 0x2f20
;;
- aruba,ap-303 |\
- aruba,ap-303h |\
- aruba,ap-365)
- caldata_extract "ART" 0x5000 0x2f20
- ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary mfginfo 0x1D) +1)
- ;;
- asus,map-ac2200)
- caldata_extract_ubi "Factory" 0x5000 0x2f20
- ;;
+ asus,map-ac2200|\
asus,rt-ac58u)
- CI_UBIPART=UBI_DEV
caldata_extract_ubi "Factory" 0x5000 0x2f20
;;
avm,fritzbox-4040)
/usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
;;
- buffalo,wtr-m2133hp)
- caldata_extract "ART" 0x5000 0x2f20
- ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x2c)
- ;;
- cellc,rtl30vw |\
- compex,wpj419 |\
- compex,wpj428 |\
- edgecore,ecw5211 |\
- edgecore,oap100 |\
- engenius,eap1300 |\
- engenius,eap2200 |\
- luma,wrtq-329acn|\
openmesh,a42 |\
openmesh,a62 |\
- qxwlan,e2600ac-c1 |\
- qxwlan,e2600ac-c2 |\
- unielec,u4019-32m)
+ plasmacloud,pa1200 |\
+ plasmacloud,pa2200)
caldata_extract "0:ART" 0x5000 0x2f20
;;
+ devolo,magic-2-wifi-next)
+ caldata_extract "ART" 0x5000 0x2f20
+ ath10k_patch_mac $(mtd_get_mac_ascii APPSBLENV WiFiMacAddress1)
+ ;;
dlink,dap-2610)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac_a)
;;
engenius,emd1)
caldata_extract "0:ART" 0x5000 0x2f20
- ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr) +1)
+ ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr) 1)
;;
engenius,emr3500)
caldata_extract "0:ART" 0x5000 0x2f20
- ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV ethaddr) +1)
+ ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV ethaddr) 1)
;;
engenius,ens620ext)
caldata_extract "ART" 0x5000 0x2f20
- ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +3)
+ ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) 3)
;;
- linksys,ea8300)
+ linksys,ea8300 |\
+ linksys,mr8300)
caldata_extract "ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add "$(cat /sys/class/net/eth0/address)" 3)
;;
meraki,mr33)
caldata_extract_ubi "ART" 0x5000 0x2f20
caldata_valid "202f" || caldata_extract "ART" 0x5000 0x2f20
- ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) +3)
- ;;
- netgear,ex6100v2 |\
- netgear,ex6150v2)
- caldata_extract "ART" 0x5000 0x2f20
- ath10k_patch_mac $(mtd_get_mac_binary dnidata 0xc)
+ ath10k_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 0x66) 3)
+ ;;
+ mikrotik,cap-ac |\
+ mikrotik,hap-ac2 |\
+ mikrotik,hap-ac3 |\
+ mikrotik,sxtsq-5-ac)
+ wlan_data="/sys/firmware/mikrotik/hard_config/wlan_data"
+ ( [ -f "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data" 0x8000 0x2f20 ) || \
+ ( [ -d "$wlan_data" ] && caldata_sysfsload_from_file "$wlan_data/data_2" 0x0 0x2f20 )
+ ;;
+ netgear,rbr50|\
+ netgear,rbs50|\
+ netgear,srr60|\
+ netgear,srs60)
+ caldata_extract_mmc "0:ART" 0x5000 0x2f20
+ ath10k_patch_mac $(mmc_get_mac_binary ARTMTD 0xc)
;;
zyxel,nbg6617 |\
zyxel,wre6606)
;;
esac
;;
+"ath10k/QCA4019/hw1.0/board-2.bin")
+case "$board" in
+ mikrotik,cap-ac |\
+ mikrotik,hap-ac2 |\
+ mikrotik,hap-ac3 |\
+ mikrotik,sxtsq-5-ac)
+ board2_create_for_mikrotik
+ ;;
+ esac
+ ;;
*)
exit 1
;;
projects / openwrt / staging / chunkeey.git / blobdiff