ucidef_set_led_usbdev "usb" "USB" "tp-link:green:usb" "1-1"
ucidef_set_led_wlan "wlan" "WLAN" "tp-link:green:wlan" "phy0tpt"
;;
+tl-wr1043n-v5|\
tl-wr1043nd-v4)
- ucidef_set_led_usbdev "usb" "USB" "tp-link:green:usb" "1-1"
ucidef_set_led_wlan "wlan" "WLAN" "tp-link:green:wlan" "phy0tpt"
ucidef_set_led_switch "wan" "WAN" "tp-link:green:wan" "switch0" "0x20"
ucidef_set_led_switch "lan1" "LAN1" "tp-link:green:lan1" "switch0" "0x10"
ucidef_set_led_switch "lan2" "LAN2" "tp-link:green:lan2" "switch0" "0x08"
ucidef_set_led_switch "lan3" "LAN3" "tp-link:green:lan3" "switch0" "0x04"
ucidef_set_led_switch "lan4" "LAN4" "tp-link:green:lan4" "switch0" "0x02"
+
+ case "$board" in
+ tl-wr1043nd-v4)
+ ucidef_set_led_usbdev "usb" "USB" "tp-link:green:usb" "1-1"
+ ;;
+ esac
;;
tl-wr2543n)
ucidef_set_led_wlan "wlan2g" "WLAN2G" "tp-link:green:wlan2g" "phy0tpt"
dir-835-a1|\
esr900|\
mynet-n750|\
- sr3200)
+ sr3200|\
+ tl-wr1043n-v5)
ucidef_add_switch "switch0" \
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
;;
fritz300e)
lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
;;
+ tl-wr1043n-v5|\
tl-wr1043nd-v4)
lan_mac=$(mtd_get_mac_binary product-info 8)
wan_mac=$(macaddr_add "$lan_mac" 1)
tl-wdr3320-v2|\
tl-wdr3500|\
tl-wr1041n-v2|\
+ tl-wr1043n-v5|\
tl-wr1043nd|\
tl-wr1043nd-v2|\
tl-wr1043nd-v4|\
*"TL-WR1041N v2")
name="tl-wr1041n-v2"
;;
+ *"TL-WR1043N v5")
+ name="tl-wr1043n-v5"
+ ;;
*"TL-WR1043ND")
name="tl-wr1043nd"
;;
tew-712br|\
tew-732br|\
tew-823dru|\
+ tl-wr1043n-v5|\
tl-wr942n-v1|\
unifi|\
unifi-outdoor|\
CONFIG_ATH79_MACH_TL_WDR6500_V2=y
CONFIG_ATH79_MACH_TL_WPA8630=y
CONFIG_ATH79_MACH_TL_WR1041N_V2=y
+CONFIG_ATH79_MACH_TL_WR1043N_V5=y
CONFIG_ATH79_MACH_TL_WR1043ND=y
CONFIG_ATH79_MACH_TL_WR1043ND_V2=y
CONFIG_ATH79_MACH_TL_WR1043ND_V4=y
CONFIG_ATH79_MACH_TL_WDR6500_V2=y
CONFIG_ATH79_MACH_TL_WPA8630=y
CONFIG_ATH79_MACH_TL_WR1041N_V2=y
+CONFIG_ATH79_MACH_TL_WR1043N_V5=y
CONFIG_ATH79_MACH_TL_WR1043ND=y
CONFIG_ATH79_MACH_TL_WR1043ND_V2=y
CONFIG_ATH79_MACH_TL_WR1043ND_V4=y
select ATH79_DEV_USB
select ATH79_DEV_WMAC
+config ATH79_MACH_TL_WR1043N_V5
+ bool "TP-LINK TL-WR1043N v5 support"
+ select SOC_QCA956X
+ select ATH79_DEV_ETH
+ select ATH79_DEV_GPIO_BUTTONS
+ select ATH79_DEV_LEDS_GPIO
+ select ATH79_DEV_M25P80
+ select ATH79_DEV_WMAC
+
config ATH79_MACH_TL_WR1043ND
bool "TP-LINK TL-WR1043ND support"
select SOC_AR913X
* Copyright (C) 2016 Matthias Schiffer <mschiffer@universe-factory.net>
* Copyright (C) 2016 Andreas Ziegler <github@andreas-ziegler.de>
* Copyright (C) 2016 Ludwig Thomeczek <ledesrc@wxorx.net>
+ * Copyright (C) 2017 Tim Thorpe <tim@tfthorpe.net>
*
* Derived from: mach-dir-869-a1.c
*
#define TL_WR1043_V4_EEPROM_ADDR 0x1fff0000
#define TL_WR1043_V4_WMAC_CALDATA_OFFSET 0x1000
+#define TL_WR1043N_V5_MAC_LOCATION 0x1ff00008
+
static struct gpio_led tl_wr1043nd_v4_leds_gpio[] __initdata = {
{
.name = "tp-link:green:wps",
MIPS_MACHINE(ATH79_MACH_TL_WR1043ND_V4, "TL-WR1043ND-v4",
"TP-LINK TL-WR1043ND v4", tl_wr1043nd_v4_setup);
+
+static struct gpio_led tl_wr1043n_v5_leds_gpio[] __initdata = {
+ {
+ .name = "tp-link:green:wps",
+ .gpio = TL_WR1043_V4_GPIO_LED_WPS,
+ .active_low = 1,
+ },
+ {
+ .name = "tp-link:green:system",
+ .gpio = TL_WR1043_V4_GPIO_LED_SYSTEM,
+ .active_low = 1,
+ },
+ {
+ .name = "tp-link:green:wlan",
+ .gpio = TL_WR1043_V4_GPIO_LED_WLAN,
+ .active_low = 1,
+ },
+ {
+ .name = "tp-link:green:wan",
+ .gpio = TL_WR1043_V4_GPIO_LED_WAN,
+ .active_low = 1,
+ },
+ {
+ .name = "tp-link:green:lan1",
+ .gpio = TL_WR1043_V4_GPIO_LED_LAN1,
+ .active_low = 1,
+ },
+ {
+ .name = "tp-link:green:lan2",
+ .gpio = TL_WR1043_V4_GPIO_LED_LAN2,
+ .active_low = 1,
+ },
+ {
+ .name = "tp-link:green:lan3",
+ .gpio = TL_WR1043_V4_GPIO_LED_LAN3,
+ .active_low = 1,
+ },
+ {
+ .name = "tp-link:green:lan4",
+ .gpio = TL_WR1043_V4_GPIO_LED_LAN4,
+ .active_low = 1,
+ },
+};
+
+/* The 1043Nv5 is identical to the 1043NDv4,
+ * only missing the usb and small firmware layout changes */
+static void __init tl_wr1043nv5_setup(void)
+{
+ u8 *art = (u8 *) KSEG1ADDR(TL_WR1043_V4_EEPROM_ADDR);
+ u8 *mac = (u8 *) KSEG1ADDR(TL_WR1043N_V5_MAC_LOCATION);
+
+ ath79_register_m25p80(NULL);
+
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(tl_wr1043n_v5_leds_gpio),
+ tl_wr1043n_v5_leds_gpio);
+ ath79_register_gpio_keys_polled(-1, TL_WR1043_V4_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(tl_wr1043nd_v4_gpio_keys),
+ tl_wr1043nd_v4_gpio_keys);
+
+ platform_device_register(&ath79_mdio0_device);
+
+ mdiobus_register_board_info(tl_wr1043nd_v4_mdio0_info,
+ ARRAY_SIZE(tl_wr1043nd_v4_mdio0_info));
+
+ ath79_register_wmac(art + TL_WR1043_V4_WMAC_CALDATA_OFFSET, mac);
+
+ ath79_init_mac(ath79_eth0_data.mac_addr, mac, 0);
+
+ /* GMAC0 is connected to an AR8337 switch */
+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
+ ath79_eth0_data.speed = SPEED_1000;
+ ath79_eth0_data.duplex = DUPLEX_FULL;
+ ath79_eth0_data.phy_mask = BIT(0);
+ ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+ ath79_register_eth(0);
+}
+
+MIPS_MACHINE(ATH79_MACH_TL_WR1043N_V5, "TL-WR1043N-v5", "TP-LINK TL-WR1043N v5",
+ tl_wr1043nv5_setup);
ATH79_MACH_TL_WDR6500_V2, /* TP-LINK TL-WDR6500 v2 */
ATH79_MACH_TL_WPA8630, /* TP-Link TL-WPA8630 */
ATH79_MACH_TL_WR1041N_V2, /* TP-LINK TL-WR1041N v2 */
+ ATH79_MACH_TL_WR1043N_V5, /* TP-LINK TL-WR1043N v5 */
ATH79_MACH_TL_WR1043ND, /* TP-LINK TL-WR1043ND */
ATH79_MACH_TL_WR1043ND_V2, /* TP-LINK TL-WR1043ND v2 */
ATH79_MACH_TL_WR1043ND_V4, /* TP-LINK TL-WR1043ND v4 */
endef
TARGET_DEVICES += tl-wr1041n-v2
+define Device/tl-wr1043n-v5
+ $(Device/archer-cxx)
+ DEVICE_TITLE := TP-LINK TL-WR1043N v5
+ BOARDNAME := TL-WR1043N-v5
+ SUPPORTED_DEVICES := tl-wr1043n-v5
+ DEVICE_PROFILE := TLWR1043
+ MTDPARTS := spi0.0:128k(factory-uboot)ro,128k(u-boot)ro,15104k(firmware),128k(product-info)ro,640k(config)ro,64k(partition-table)ro,128k(logs)ro,64k(art)ro
+ IMAGE_SIZE := 15104k
+ TPLINK_BOARD_ID := TLWR1043NV5
+endef
+
define Device/tl-wr1043nd-v1
$(Device/tplink-8m)
DEVICE_TITLE := TP-LINK TL-WR1043N/ND v1
IMAGE/sysupgrade.bin := append-rootfs | mktplinkfw sysupgrade -v 3.13.99
IMAGE/factory.bin := append-rootfs | mktplinkfw factory -v 3.13.99
endef
-TARGET_DEVICES += tl-wr1043nd-v1 tl-wr1043nd-v2 tl-wr1043nd-v3 tl-wr1043nd-v4 tl-wr2543-v1
+TARGET_DEVICES += tl-wr1043nd-v1 tl-wr1043nd-v2 tl-wr1043nd-v3 tl-wr1043nd-v4 tl-wr1043n-v5 tl-wr2543-v1
define Device/tl-wr703n-v1
$(Device/tplink-4mlzma)
# CONFIG_ATH79_MACH_TL_WDR6500_V2 is not set
# CONFIG_ATH79_MACH_TL_WPA8630 is not set
# CONFIG_ATH79_MACH_TL_WR1041N_V2 is not set
+# CONFIG_ATH79_MACH_TL_WR1043N_V5 is not set
# CONFIG_ATH79_MACH_TL_WR1043ND is not set
# CONFIG_ATH79_MACH_TL_WR1043ND_V2 is not set
# CONFIG_ATH79_MACH_TL_WR1043ND_V4 is not set
# CONFIG_ATH79_MACH_TL_WDR6500_V2 is not set
# CONFIG_ATH79_MACH_TL_WPA8630 is not set
# CONFIG_ATH79_MACH_TL_WR1041N_V2 is not set
+# CONFIG_ATH79_MACH_TL_WR1043N_V5 is not set
# CONFIG_ATH79_MACH_TL_WR1043ND is not set
# CONFIG_ATH79_MACH_TL_WR1043ND_V2 is not set
# CONFIG_ATH79_MACH_TL_WR1043ND_V4 is not set
.last_sysupgrade_partition = "file-system"
},
+ /** Firmware layout for the TL-WR1043 v5 */
+ {
+ .id = "TLWR1043NV5",
+ .vendor = "",
+ .support_list =
+ "SupportList:\n"
+ "{product_name:TL-WR1043N,product_ver:5.0.0,special_id:45550000}\n"
+ "{product_name:TL-WR1043N,product_ver:5.0.0,special_id:55530000}\n",
+ .support_trail = '\x00',
+ .soft_ver = "soft_ver:1.0.0\n",
+ .partitions = {
+ {"factory-boot", 0x00000, 0x20000},
+ {"fs-uboot", 0x20000, 0x20000},
+ {"os-image", 0x40000, 0x180000},
+ {"file-system", 0x1c0000, 0xd40000},
+ {"default-mac", 0xf00000, 0x00200},
+ {"pin", 0xf00200, 0x00200},
+ {"device-id", 0xf00400, 0x00100},
+ {"product-info", 0xf00500, 0x0fb00},
+ {"soft-version", 0xf10000, 0x01000},
+ {"extra-para", 0xf11000, 0x01000},
+ {"support-list", 0xf12000, 0x0a000},
+ {"profile", 0xf1c000, 0x04000},
+ {"default-config", 0xf20000, 0x10000},
+ {"user-config", 0xf30000, 0x40000},
+ {"qos-db", 0xf70000, 0x40000},
+ {"certificate", 0xfb0000, 0x10000},
+ {"partition-table", 0xfc0000, 0x10000},
+ {"log", 0xfd0000, 0x20000},
+ {"radio", 0xff0000, 0x10000},
+ {NULL, 0, 0}
+ },
+ .first_sysupgrade_partition = "os-image",
+ .last_sysupgrade_partition = "file-system"
+ },
+
/** Firmware layout for the TL-WR1043 v4 */
{
.id = "TLWR1043NDV4",
parts[3] = read_file("os-image", kernel_image, false);
parts[4] = read_file("file-system", rootfs_image, add_jffs2_eof);
- if (strcasecmp(info->id, "ARCHER-C25-V1") == 0) {
+ /* Some devices need the extra-para partition to accept the firmware */
+ if (strcasecmp(info->id, "ARCHER-C25-V1") == 0 ||
+ strcasecmp(info->id, "TLWR1043NV5") == 0) {
const char mdat[11] = {0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x01, 0x00, 0x00};
parts[5] = put_data("extra-para", mdat, 11);
} else if (strcasecmp(info->id, "ARCHER-C7-V4") == 0) {
projects / openwrt / staging / chunkeey.git / commitdiff