+++ /dev/null
-CONFIG_ADM6996_PHY=y
-CONFIG_AR2315_WDT=y
-CONFIG_AR8216_PHY=y
-CONFIG_ARCH_BINFMT_ELF_STATE=y
-CONFIG_ARCH_CLOCKSOURCE_DATA=y
-CONFIG_ARCH_DISCARD_MEMBLOCK=y
-CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
-CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
-# CONFIG_ARCH_HAS_GCOV_PROFILE_ALL is not set
-# CONFIG_ARCH_HAS_SG_CHAIN is not set
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
-CONFIG_ARCH_MIGHT_HAVE_PC_SERIO=y
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-CONFIG_ARCH_SUPPORTS_UPROBES=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARCH_USE_BUILTIN_BSWAP=y
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
-CONFIG_ATH25=y
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_CEVT_R4K=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_CMDLINE="console=ttyS0,9600 rootfstype=squashfs,jffs2"
-CONFIG_CMDLINE_BOOL=y
-# CONFIG_CMDLINE_OVERRIDE is not set
-CONFIG_CPU_BIG_ENDIAN=y
-CONFIG_CPU_GENERIC_DUMP_TLB=y
-CONFIG_CPU_HAS_PREFETCH=y
-CONFIG_CPU_HAS_SYNC=y
-CONFIG_CPU_MIPS32=y
-CONFIG_CPU_MIPS32_R1=y
-CONFIG_CPU_MIPSR1=y
-CONFIG_CPU_NEEDS_NO_SMARTMIPS_OR_MICROMIPS=y
-CONFIG_CPU_R4K_CACHE_TLB=y
-CONFIG_CPU_R4K_FPU=y
-CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
-CONFIG_CPU_SUPPORTS_HIGHMEM=y
-CONFIG_CRYPTO_RNG2=y
-CONFIG_CRYPTO_WORKQUEUE=y
-CONFIG_CSRC_R4K=y
-CONFIG_DMA_NONCOHERENT=y
-CONFIG_EARLY_PRINTK=y
-CONFIG_ETHERNET_PACKET_MANGLE=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CMOS_UPDATE=y
-CONFIG_GENERIC_IO=y
-CONFIG_GENERIC_IRQ_CHIP=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_SCHED_CLOCK=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_TIME_VSYSCALL=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_AR2315=y
-CONFIG_GPIO_AR5312=y
-CONFIG_GPIO_DEVRES=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_HARDWARE_WATCHPOINTS=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT_MAP=y
-# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
-# CONFIG_HAVE_ARCH_BITREVERSE is not set
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
-CONFIG_HAVE_ARCH_TRACEHOOK=y
-# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
-CONFIG_HAVE_BPF_JIT=y
-CONFIG_HAVE_CC_STACKPROTECTOR=y
-CONFIG_HAVE_CONTEXT_TRACKING=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DEBUG_KMEMLEAK=y
-CONFIG_HAVE_DEBUG_STACKOVERFLOW=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_ATTRS=y
-CONFIG_HAVE_DMA_CONTIGUOUS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_IDE=y
-CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
-CONFIG_HAVE_LATENCYTOP_SUPPORT=y
-CONFIG_HAVE_MEMBLOCK=y
-CONFIG_HAVE_MEMBLOCK_NODE_MAP=y
-CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
-CONFIG_HAVE_NET_DSA=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
-CONFIG_HW_HAS_PCI=y
-CONFIG_HW_RANDOM=y
-CONFIG_HZ_PERIODIC=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_IP17XX_PHY=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_IRQ_MIPS_CPU=y
-CONFIG_IRQ_WORK=y
-CONFIG_LEDS_GPIO=y
-CONFIG_MDIO_BOARDINFO=y
-CONFIG_MIPS=y
-CONFIG_MIPS_CLOCK_VSYSCALL=y
-CONFIG_MIPS_CMDLINE_FROM_BOOTLOADER=y
-# CONFIG_MIPS_HUGE_TLB_SUPPORT is not set
-CONFIG_MIPS_L1_CACHE_SHIFT=5
-# CONFIG_MIPS_MACHINE is not set
-CONFIG_MODULES_USE_ELF_REL=y
-CONFIG_MTD_AR2315=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-# CONFIG_MTD_CFI_GEOMETRY is not set
-# CONFIG_MTD_CFI_INTELEXT is not set
-CONFIG_MTD_MYLOADER_PARTS=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-3
-CONFIG_MTD_REDBOOT_PARTS=y
-CONFIG_MVSWITCH_PHY=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_PER_CPU_KM=y
-CONFIG_NET_AR231X=y
-CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y
-# CONFIG_NO_IOPORT_MAP is not set
-# CONFIG_OF is not set
-CONFIG_PCI=y
-CONFIG_PCI_AR2315=y
-CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
-CONFIG_PCI_DOMAINS=y
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PGTABLE_LEVELS=2
-CONFIG_PHYLIB=y
-# CONFIG_RCU_STALL_COMMON is not set
-CONFIG_SCHED_HRTICK=y
-# CONFIG_SCHED_INFO is not set
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SERIAL_8250_FSL is not set
-CONFIG_SERIAL_8250_NR_UARTS=1
-CONFIG_SERIAL_8250_RUNTIME_UARTS=1
-CONFIG_SOC_AR2315=y
-CONFIG_SOC_AR5312=y
-CONFIG_SRCU=y
-# CONFIG_SWAP is not set
-CONFIG_SWCONFIG=y
-CONFIG_SYSCTL_EXCEPTION_TRACE=y
-CONFIG_SYS_HAS_CPU_MIPS32_R1=y
-CONFIG_SYS_HAS_EARLY_PRINTK=y
-CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
-CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
-CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
-CONFIG_TICK_CPU_ACCOUNTING=y
-CONFIG_USB_SUPPORT=y
-CONFIG_ZONE_DMA_FLAG=0
+++ /dev/null
---- a/arch/mips/ath25/Kconfig
-+++ b/arch/mips/ath25/Kconfig
-@@ -1,6 +1,7 @@
- config SOC_AR5312
- bool "Atheros AR5312/AR2312+ SoC support"
- depends on ATH25
-+ select GPIO_AR5312
- default y
-
- config SOC_AR2315
---- a/arch/mips/ath25/ar5312.c
-+++ b/arch/mips/ath25/ar5312.c
-@@ -22,6 +22,7 @@
- #include <linux/platform_device.h>
- #include <linux/mtd/physmap.h>
- #include <linux/reboot.h>
-+#include <linux/gpio.h>
- #include <asm/bootinfo.h>
- #include <asm/reboot.h>
- #include <asm/time.h>
-@@ -180,6 +181,22 @@ static struct platform_device ar5312_phy
- .num_resources = 1,
- };
-
-+static struct resource ar5312_gpio_res[] = {
-+ {
-+ .name = "ar5312-gpio",
-+ .flags = IORESOURCE_MEM,
-+ .start = AR5312_GPIO_BASE,
-+ .end = AR5312_GPIO_BASE + AR5312_GPIO_SIZE - 1,
-+ },
-+};
-+
-+static struct platform_device ar5312_gpio = {
-+ .name = "ar5312-gpio",
-+ .id = -1,
-+ .resource = ar5312_gpio_res,
-+ .num_resources = ARRAY_SIZE(ar5312_gpio_res),
-+};
-+
- static void __init ar5312_flash_init(void)
- {
- void __iomem *flashctl_base;
-@@ -247,6 +264,8 @@ void __init ar5312_init_devices(void)
-
- platform_device_register(&ar5312_physmap_flash);
-
-+ platform_device_register(&ar5312_gpio);
-+
- switch (ath25_soc) {
- case ATH25_SOC_AR5312:
- if (!ath25_board.radio)
---- a/drivers/gpio/Kconfig
-+++ b/drivers/gpio/Kconfig
-@@ -142,6 +142,13 @@ config GPIO_BRCMSTB
- help
- Say yes here to enable GPIO support for Broadcom STB (BCM7XXX) SoCs.
-
-+config GPIO_AR5312
-+ bool "AR5312 SoC GPIO support"
-+ default y if SOC_AR5312
-+ depends on SOC_AR5312
-+ help
-+ Say yes here to enable GPIO support for Atheros AR5312/AR2312+ SoCs.
-+
- config GPIO_CLPS711X
- tristate "CLPS711X GPIO support"
- depends on ARCH_CLPS711X || COMPILE_TEST
---- a/drivers/gpio/Makefile
-+++ b/drivers/gpio/Makefile
-@@ -21,6 +21,7 @@ obj-$(CONFIG_GPIO_ADP5588) += gpio-adp55
- obj-$(CONFIG_GPIO_ALTERA) += gpio-altera.o
- obj-$(CONFIG_GPIO_AMD8111) += gpio-amd8111.o
- obj-$(CONFIG_GPIO_AMDPT) += gpio-amdpt.o
-+obj-$(CONFIG_GPIO_AR5312) += gpio-ar5312.o
- obj-$(CONFIG_GPIO_ARIZONA) += gpio-arizona.o
- obj-$(CONFIG_ATH79) += gpio-ath79.o
- obj-$(CONFIG_GPIO_BCM_KONA) += gpio-bcm-kona.o
---- /dev/null
-+++ b/drivers/gpio/gpio-ar5312.c
-@@ -0,0 +1,121 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
-+ * Copyright (C) 2006 FON Technology, SL.
-+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006-2009 Felix Fietkau <nbd@nbd.name>
-+ * Copyright (C) 2012 Alexandros C. Couloumbis <alex@ozo.com>
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/platform_device.h>
-+#include <linux/gpio.h>
-+
-+#define DRIVER_NAME "ar5312-gpio"
-+
-+#define AR5312_GPIO_DO 0x00 /* output register */
-+#define AR5312_GPIO_DI 0x04 /* intput register */
-+#define AR5312_GPIO_CR 0x08 /* control register */
-+
-+#define AR5312_GPIO_CR_M(x) (1 << (x)) /* mask for i/o */
-+#define AR5312_GPIO_CR_O(x) (0 << (x)) /* mask for output */
-+#define AR5312_GPIO_CR_I(x) (1 << (x)) /* mask for input */
-+#define AR5312_GPIO_CR_INT(x) (1 << ((x)+8)) /* mask for interrupt */
-+#define AR5312_GPIO_CR_UART(x) (1 << ((x)+16)) /* uart multiplex */
-+
-+#define AR5312_GPIO_NUM 8
-+
-+static void __iomem *ar5312_mem;
-+
-+static inline u32 ar5312_gpio_reg_read(unsigned reg)
-+{
-+ return __raw_readl(ar5312_mem + reg);
-+}
-+
-+static inline void ar5312_gpio_reg_write(unsigned reg, u32 val)
-+{
-+ __raw_writel(val, ar5312_mem + reg);
-+}
-+
-+static inline void ar5312_gpio_reg_mask(unsigned reg, u32 mask, u32 val)
-+{
-+ ar5312_gpio_reg_write(reg, (ar5312_gpio_reg_read(reg) & ~mask) | val);
-+}
-+
-+static int ar5312_gpio_get_val(struct gpio_chip *chip, unsigned gpio)
-+{
-+ return (ar5312_gpio_reg_read(AR5312_GPIO_DI) >> gpio) & 1;
-+}
-+
-+static void ar5312_gpio_set_val(struct gpio_chip *chip, unsigned gpio, int val)
-+{
-+ u32 reg = ar5312_gpio_reg_read(AR5312_GPIO_DO);
-+
-+ reg = val ? reg | (1 << gpio) : reg & ~(1 << gpio);
-+ ar5312_gpio_reg_write(AR5312_GPIO_DO, reg);
-+}
-+
-+static int ar5312_gpio_dir_in(struct gpio_chip *chip, unsigned gpio)
-+{
-+ ar5312_gpio_reg_mask(AR5312_GPIO_CR, 0, 1 << gpio);
-+ return 0;
-+}
-+
-+static int ar5312_gpio_dir_out(struct gpio_chip *chip, unsigned gpio, int val)
-+{
-+ ar5312_gpio_reg_mask(AR5312_GPIO_CR, 1 << gpio, 0);
-+ ar5312_gpio_set_val(chip, gpio, val);
-+ return 0;
-+}
-+
-+static struct gpio_chip ar5312_gpio_chip = {
-+ .label = DRIVER_NAME,
-+ .direction_input = ar5312_gpio_dir_in,
-+ .direction_output = ar5312_gpio_dir_out,
-+ .set = ar5312_gpio_set_val,
-+ .get = ar5312_gpio_get_val,
-+ .base = 0,
-+ .ngpio = AR5312_GPIO_NUM,
-+};
-+
-+static int ar5312_gpio_probe(struct platform_device *pdev)
-+{
-+ struct device *dev = &pdev->dev;
-+ struct resource *res;
-+ int ret;
-+
-+ if (ar5312_mem)
-+ return -EBUSY;
-+
-+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ ar5312_mem = devm_ioremap_resource(dev, res);
-+ if (IS_ERR(ar5312_mem))
-+ return PTR_ERR(ar5312_mem);
-+
-+ ar5312_gpio_chip.dev = dev;
-+ ret = gpiochip_add(&ar5312_gpio_chip);
-+ if (ret) {
-+ dev_err(dev, "failed to add gpiochip\n");
-+ return ret;
-+ }
-+
-+ return 0;
-+}
-+
-+static struct platform_driver ar5312_gpio_driver = {
-+ .probe = ar5312_gpio_probe,
-+ .driver = {
-+ .name = DRIVER_NAME,
-+ .owner = THIS_MODULE,
-+ }
-+};
-+
-+static int __init ar5312_gpio_init(void)
-+{
-+ return platform_driver_register(&ar5312_gpio_driver);
-+}
-+subsys_initcall(ar5312_gpio_init);
---- a/arch/mips/Kconfig
-+++ b/arch/mips/Kconfig
-@@ -118,6 +118,7 @@ config ATH25
- select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_HAS_EARLY_PRINTK
-+ select ARCH_REQUIRE_GPIOLIB
- help
- Support for Atheros AR231x and Atheros AR531x based boards
-
+++ /dev/null
---- a/arch/mips/ath25/Kconfig
-+++ b/arch/mips/ath25/Kconfig
-@@ -7,6 +7,7 @@ config SOC_AR5312
- config SOC_AR2315
- bool "Atheros AR2315+ SoC support"
- depends on ATH25
-+ select GPIO_AR2315
- default y
-
- config PCI_AR2315
---- a/arch/mips/ath25/ar2315.c
-+++ b/arch/mips/ath25/ar2315.c
-@@ -21,6 +21,8 @@
- #include <linux/interrupt.h>
- #include <linux/platform_device.h>
- #include <linux/reboot.h>
-+#include <linux/delay.h>
-+#include <linux/gpio.h>
- #include <asm/bootinfo.h>
- #include <asm/reboot.h>
- #include <asm/time.h>
-@@ -167,11 +169,42 @@ void __init ar2315_arch_init_irq(void)
- ar2315_misc_irq_domain = domain;
- }
-
-+static struct resource ar2315_gpio_res[] = {
-+ {
-+ .name = "ar2315-gpio",
-+ .flags = IORESOURCE_MEM,
-+ .start = AR2315_RST_BASE + AR2315_GPIO,
-+ .end = AR2315_RST_BASE + AR2315_GPIO + 0x10 - 1,
-+ },
-+ {
-+ .name = "ar2315-gpio",
-+ .flags = IORESOURCE_IRQ,
-+ },
-+ {
-+ .name = "ar2315-gpio-irq-base",
-+ .flags = IORESOURCE_IRQ,
-+ .start = AR231X_GPIO_IRQ_BASE,
-+ .end = AR231X_GPIO_IRQ_BASE,
-+ }
-+};
-+
-+static struct platform_device ar2315_gpio = {
-+ .id = -1,
-+ .name = "ar2315-gpio",
-+ .resource = ar2315_gpio_res,
-+ .num_resources = ARRAY_SIZE(ar2315_gpio_res)
-+};
-+
- void __init ar2315_init_devices(void)
- {
- /* Find board configuration */
- ath25_find_config(AR2315_SPI_READ_BASE, AR2315_SPI_READ_SIZE);
-
-+ ar2315_gpio_res[1].start = irq_create_mapping(ar2315_misc_irq_domain,
-+ AR2315_MISC_IRQ_GPIO);
-+ ar2315_gpio_res[1].end = ar2315_gpio_res[1].start;
-+ platform_device_register(&ar2315_gpio);
-+
- ath25_add_wmac(0, AR2315_WLAN0_BASE, AR2315_IRQ_WLAN0);
- }
-
-@@ -187,8 +220,8 @@ static void ar2315_restart(char *command
- /* Cold reset does not work on the AR2315/6, use the GPIO reset bits
- * a workaround. Give it some time to attempt a gpio based hardware
- * reset (atheros reference design workaround) */
--
-- /* TODO: implement the GPIO reset workaround */
-+ gpio_request_one(AR2315_RESET_GPIO, GPIOF_OUT_INIT_LOW, "Reset");
-+ mdelay(100);
-
- /* Some boards (e.g. Senao EOC-2610) don't implement the reset logic
- * workaround. Attempt to jump to the mips reset location -
---- a/drivers/gpio/Kconfig
-+++ b/drivers/gpio/Kconfig
-@@ -142,6 +142,13 @@ config GPIO_BRCMSTB
- help
- Say yes here to enable GPIO support for Broadcom STB (BCM7XXX) SoCs.
-
-+config GPIO_AR2315
-+ bool "AR2315 SoC GPIO support"
-+ default y if SOC_AR2315
-+ depends on SOC_AR2315
-+ help
-+ Say yes here to enable GPIO support for Atheros AR2315+ SoCs.
-+
- config GPIO_AR5312
- bool "AR5312 SoC GPIO support"
- default y if SOC_AR5312
---- a/drivers/gpio/Makefile
-+++ b/drivers/gpio/Makefile
-@@ -21,6 +21,7 @@ obj-$(CONFIG_GPIO_ADP5588) += gpio-adp55
- obj-$(CONFIG_GPIO_ALTERA) += gpio-altera.o
- obj-$(CONFIG_GPIO_AMD8111) += gpio-amd8111.o
- obj-$(CONFIG_GPIO_AMDPT) += gpio-amdpt.o
-+obj-$(CONFIG_GPIO_AR2315) += gpio-ar2315.o
- obj-$(CONFIG_GPIO_AR5312) += gpio-ar5312.o
- obj-$(CONFIG_GPIO_ARIZONA) += gpio-arizona.o
- obj-$(CONFIG_ATH79) += gpio-ath79.o
---- /dev/null
-+++ b/drivers/gpio/gpio-ar2315.c
-@@ -0,0 +1,233 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2003 Atheros Communications, Inc., All Rights Reserved.
-+ * Copyright (C) 2006 FON Technology, SL.
-+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006 Felix Fietkau <nbd@nbd.name>
-+ * Copyright (C) 2012 Alexandros C. Couloumbis <alex@ozo.com>
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/platform_device.h>
-+#include <linux/gpio.h>
-+#include <linux/irq.h>
-+
-+#define DRIVER_NAME "ar2315-gpio"
-+
-+#define AR2315_GPIO_DI 0x0000
-+#define AR2315_GPIO_DO 0x0008
-+#define AR2315_GPIO_DIR 0x0010
-+#define AR2315_GPIO_INT 0x0018
-+
-+#define AR2315_GPIO_DIR_M(x) (1 << (x)) /* mask for i/o */
-+#define AR2315_GPIO_DIR_O(x) (1 << (x)) /* output */
-+#define AR2315_GPIO_DIR_I(x) (0) /* input */
-+
-+#define AR2315_GPIO_INT_NUM_M 0x3F /* mask for GPIO num */
-+#define AR2315_GPIO_INT_TRIG(x) ((x) << 6) /* interrupt trigger */
-+#define AR2315_GPIO_INT_TRIG_M (0x3 << 6) /* mask for int trig */
-+
-+#define AR2315_GPIO_INT_TRIG_OFF 0 /* Triggerring off */
-+#define AR2315_GPIO_INT_TRIG_LOW 1 /* Low Level Triggered */
-+#define AR2315_GPIO_INT_TRIG_HIGH 2 /* High Level Triggered */
-+#define AR2315_GPIO_INT_TRIG_EDGE 3 /* Edge Triggered */
-+
-+#define AR2315_GPIO_NUM 22
-+
-+static u32 ar2315_gpio_intmask;
-+static u32 ar2315_gpio_intval;
-+static unsigned ar2315_gpio_irq_base;
-+static void __iomem *ar2315_mem;
-+
-+static inline u32 ar2315_gpio_reg_read(unsigned reg)
-+{
-+ return __raw_readl(ar2315_mem + reg);
-+}
-+
-+static inline void ar2315_gpio_reg_write(unsigned reg, u32 val)
-+{
-+ __raw_writel(val, ar2315_mem + reg);
-+}
-+
-+static inline void ar2315_gpio_reg_mask(unsigned reg, u32 mask, u32 val)
-+{
-+ ar2315_gpio_reg_write(reg, (ar2315_gpio_reg_read(reg) & ~mask) | val);
-+}
-+
-+static void ar2315_gpio_irq_handler(struct irq_desc *desc)
-+{
-+ u32 pend;
-+ int bit = -1;
-+
-+ /* only do one gpio interrupt at a time */
-+ pend = ar2315_gpio_reg_read(AR2315_GPIO_DI);
-+ pend ^= ar2315_gpio_intval;
-+ pend &= ar2315_gpio_intmask;
-+
-+ if (pend) {
-+ bit = fls(pend) - 1;
-+ pend &= ~(1 << bit);
-+ ar2315_gpio_intval ^= (1 << bit);
-+ }
-+
-+ /* Enable interrupt with edge detection */
-+ if ((ar2315_gpio_reg_read(AR2315_GPIO_DIR) & AR2315_GPIO_DIR_M(bit)) !=
-+ AR2315_GPIO_DIR_I(bit))
-+ return;
-+
-+ if (bit >= 0)
-+ generic_handle_irq(ar2315_gpio_irq_base + bit);
-+}
-+
-+static void ar2315_gpio_int_setup(unsigned gpio, int trig)
-+{
-+ u32 reg = ar2315_gpio_reg_read(AR2315_GPIO_INT);
-+
-+ reg &= ~(AR2315_GPIO_INT_NUM_M | AR2315_GPIO_INT_TRIG_M);
-+ reg |= gpio | AR2315_GPIO_INT_TRIG(trig);
-+ ar2315_gpio_reg_write(AR2315_GPIO_INT, reg);
-+}
-+
-+static void ar2315_gpio_irq_unmask(struct irq_data *d)
-+{
-+ unsigned gpio = d->irq - ar2315_gpio_irq_base;
-+ u32 dir = ar2315_gpio_reg_read(AR2315_GPIO_DIR);
-+
-+ /* Enable interrupt with edge detection */
-+ if ((dir & AR2315_GPIO_DIR_M(gpio)) != AR2315_GPIO_DIR_I(gpio))
-+ return;
-+
-+ ar2315_gpio_intmask |= (1 << gpio);
-+ ar2315_gpio_int_setup(gpio, AR2315_GPIO_INT_TRIG_EDGE);
-+}
-+
-+static void ar2315_gpio_irq_mask(struct irq_data *d)
-+{
-+ unsigned gpio = d->irq - ar2315_gpio_irq_base;
-+
-+ /* Disable interrupt */
-+ ar2315_gpio_intmask &= ~(1 << gpio);
-+ ar2315_gpio_int_setup(gpio, AR2315_GPIO_INT_TRIG_OFF);
-+}
-+
-+static struct irq_chip ar2315_gpio_irq_chip = {
-+ .name = DRIVER_NAME,
-+ .irq_unmask = ar2315_gpio_irq_unmask,
-+ .irq_mask = ar2315_gpio_irq_mask,
-+};
-+
-+static void ar2315_gpio_irq_init(unsigned irq)
-+{
-+ unsigned i;
-+
-+ ar2315_gpio_intval = ar2315_gpio_reg_read(AR2315_GPIO_DI);
-+ for (i = 0; i < AR2315_GPIO_NUM; i++) {
-+ unsigned _irq = ar2315_gpio_irq_base + i;
-+
-+ irq_set_chip_and_handler(_irq, &ar2315_gpio_irq_chip,
-+ handle_level_irq);
-+ }
-+ irq_set_chained_handler(irq, ar2315_gpio_irq_handler);
-+}
-+
-+static int ar2315_gpio_get_val(struct gpio_chip *chip, unsigned gpio)
-+{
-+ return (ar2315_gpio_reg_read(AR2315_GPIO_DI) >> gpio) & 1;
-+}
-+
-+static void ar2315_gpio_set_val(struct gpio_chip *chip, unsigned gpio, int val)
-+{
-+ u32 reg = ar2315_gpio_reg_read(AR2315_GPIO_DO);
-+
-+ reg = val ? reg | (1 << gpio) : reg & ~(1 << gpio);
-+ ar2315_gpio_reg_write(AR2315_GPIO_DO, reg);
-+}
-+
-+static int ar2315_gpio_dir_in(struct gpio_chip *chip, unsigned gpio)
-+{
-+ ar2315_gpio_reg_mask(AR2315_GPIO_DIR, 1 << gpio, 0);
-+ return 0;
-+}
-+
-+static int ar2315_gpio_dir_out(struct gpio_chip *chip, unsigned gpio, int val)
-+{
-+ ar2315_gpio_reg_mask(AR2315_GPIO_DIR, 0, 1 << gpio);
-+ ar2315_gpio_set_val(chip, gpio, val);
-+ return 0;
-+}
-+
-+static int ar2315_gpio_to_irq(struct gpio_chip *chip, unsigned gpio)
-+{
-+ return ar2315_gpio_irq_base + gpio;
-+}
-+
-+static struct gpio_chip ar2315_gpio_chip = {
-+ .label = DRIVER_NAME,
-+ .direction_input = ar2315_gpio_dir_in,
-+ .direction_output = ar2315_gpio_dir_out,
-+ .set = ar2315_gpio_set_val,
-+ .get = ar2315_gpio_get_val,
-+ .to_irq = ar2315_gpio_to_irq,
-+ .base = 0,
-+ .ngpio = AR2315_GPIO_NUM,
-+};
-+
-+static int ar2315_gpio_probe(struct platform_device *pdev)
-+{
-+ struct device *dev = &pdev->dev;
-+ struct resource *res;
-+ unsigned irq;
-+ int ret;
-+
-+ if (ar2315_mem)
-+ return -EBUSY;
-+
-+ res = platform_get_resource_byname(pdev, IORESOURCE_IRQ,
-+ "ar2315-gpio-irq-base");
-+ if (!res) {
-+ dev_err(dev, "not found GPIO IRQ base\n");
-+ return -ENXIO;
-+ }
-+ ar2315_gpio_irq_base = res->start;
-+
-+ res = platform_get_resource_byname(pdev, IORESOURCE_IRQ, DRIVER_NAME);
-+ if (!res) {
-+ dev_err(dev, "not found IRQ number\n");
-+ return -ENXIO;
-+ }
-+ irq = res->start;
-+
-+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, DRIVER_NAME);
-+ ar2315_mem = devm_ioremap_resource(dev, res);
-+ if (IS_ERR(ar2315_mem))
-+ return PTR_ERR(ar2315_mem);
-+
-+ ar2315_gpio_chip.dev = dev;
-+ ret = gpiochip_add(&ar2315_gpio_chip);
-+ if (ret) {
-+ dev_err(dev, "failed to add gpiochip\n");
-+ return ret;
-+ }
-+
-+ ar2315_gpio_irq_init(irq);
-+
-+ return 0;
-+}
-+
-+static struct platform_driver ar2315_gpio_driver = {
-+ .probe = ar2315_gpio_probe,
-+ .driver = {
-+ .name = DRIVER_NAME,
-+ .owner = THIS_MODULE,
-+ }
-+};
-+
-+static int __init ar2315_gpio_init(void)
-+{
-+ return platform_driver_register(&ar2315_gpio_driver);
-+}
-+subsys_initcall(ar2315_gpio_init);
---- a/arch/mips/ath25/devices.h
-+++ b/arch/mips/ath25/devices.h
-@@ -3,6 +3,11 @@
-
- #include <linux/cpu.h>
-
-+#define AR231X_GPIO_IRQ_BASE 0x30
-+
-+/* GPIO number for AR2315/16 reset issue workaround */
-+#define AR2315_RESET_GPIO 5
-+
- #define ATH25_REG_MS(_val, _field) (((_val) & _field##_M) >> _field##_S)
-
- #define ATH25_IRQ_CPU_CLOCK (MIPS_CPU_IRQ_BASE + 7) /* C0_CAUSE: 0x8000 */
---- a/arch/mips/ath25/ar2315_regs.h
-+++ b/arch/mips/ath25/ar2315_regs.h
-@@ -315,6 +315,9 @@
- #define AR2315_MEM_CFG_BANKADDR_BITS_M 0x00000018
- #define AR2315_MEM_CFG_BANKADDR_BITS_S 3
-
-+/* GPIO MMR base address */
-+#define AR2315_GPIO 0x0088
-+
- /*
- * Local Bus Interface Registers
- */
+++ /dev/null
---- a/drivers/net/ethernet/atheros/Makefile
-+++ b/drivers/net/ethernet/atheros/Makefile
-@@ -7,3 +7,4 @@ obj-$(CONFIG_ATL2) += atlx/
- obj-$(CONFIG_ATL1E) += atl1e/
- obj-$(CONFIG_ATL1C) += atl1c/
- obj-$(CONFIG_ALX) += alx/
-+obj-$(CONFIG_NET_AR231X) += ar231x/
---- a/drivers/net/ethernet/atheros/Kconfig
-+++ b/drivers/net/ethernet/atheros/Kconfig
-@@ -5,7 +5,7 @@
- config NET_VENDOR_ATHEROS
- bool "Atheros devices"
- default y
-- depends on PCI
-+ depends on (PCI || ATH25)
- ---help---
- If you have a network (Ethernet) card belonging to this class, say Y.
-
-@@ -78,4 +78,10 @@ config ALX
- To compile this driver as a module, choose M here. The module
- will be called alx.
-
-+config NET_AR231X
-+ tristate "Atheros AR231X built-in Ethernet support"
-+ depends on ATH25
-+ help
-+ Support for the AR231x/531x ethernet controller
-+
- endif # NET_VENDOR_ATHEROS
---- /dev/null
-+++ b/drivers/net/ethernet/atheros/ar231x/Makefile
-@@ -0,0 +1 @@
-+obj-$(CONFIG_NET_AR231X) += ar231x.o
---- /dev/null
-+++ b/drivers/net/ethernet/atheros/ar231x/ar231x.c
-@@ -0,0 +1,1206 @@
-+/*
-+ * ar231x.c: Linux driver for the Atheros AR231x Ethernet device.
-+ *
-+ * Copyright (C) 2004 by Sameer Dekate <sdekate@arubanetworks.com>
-+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006-2009 Felix Fietkau <nbd@nbd.name>
-+ *
-+ * Thanks to Atheros for providing hardware and documentation
-+ * enabling me to write this driver.
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * Additional credits:
-+ * This code is taken from John Taylor's Sibyte driver and then
-+ * modified for the AR2313.
-+ */
-+
-+#include <linux/module.h>
-+#include <linux/types.h>
-+#include <linux/errno.h>
-+#include <linux/ioport.h>
-+#include <linux/netdevice.h>
-+#include <linux/etherdevice.h>
-+#include <linux/interrupt.h>
-+#include <linux/skbuff.h>
-+#include <linux/init.h>
-+#include <linux/delay.h>
-+#include <linux/mm.h>
-+#include <linux/mii.h>
-+#include <linux/phy.h>
-+#include <linux/platform_device.h>
-+#include <linux/io.h>
-+
-+#define AR2313_MTU 1692
-+#define AR2313_PRIOS 1
-+#define AR2313_QUEUES (2*AR2313_PRIOS)
-+#define AR2313_DESCR_ENTRIES 64
-+
-+#ifndef min
-+#define min(a, b) (((a) < (b)) ? (a) : (b))
-+#endif
-+
-+#ifndef SMP_CACHE_BYTES
-+#define SMP_CACHE_BYTES L1_CACHE_BYTES
-+#endif
-+
-+#define AR2313_MBOX_SET_BIT 0x8
-+
-+#include "ar231x.h"
-+
-+/**
-+ * New interrupt handler strategy:
-+ *
-+ * An old interrupt handler worked using the traditional method of
-+ * replacing an skbuff with a new one when a packet arrives. However
-+ * the rx rings do not need to contain a static number of buffer
-+ * descriptors, thus it makes sense to move the memory allocation out
-+ * of the main interrupt handler and do it in a bottom half handler
-+ * and only allocate new buffers when the number of buffers in the
-+ * ring is below a certain threshold. In order to avoid starving the
-+ * NIC under heavy load it is however necessary to force allocation
-+ * when hitting a minimum threshold. The strategy for alloction is as
-+ * follows:
-+ *
-+ * RX_LOW_BUF_THRES - allocate buffers in the bottom half
-+ * RX_PANIC_LOW_THRES - we are very low on buffers, allocate
-+ * the buffers in the interrupt handler
-+ * RX_RING_THRES - maximum number of buffers in the rx ring
-+ *
-+ * One advantagous side effect of this allocation approach is that the
-+ * entire rx processing can be done without holding any spin lock
-+ * since the rx rings and registers are totally independent of the tx
-+ * ring and its registers. This of course includes the kmalloc's of
-+ * new skb's. Thus start_xmit can run in parallel with rx processing
-+ * and the memory allocation on SMP systems.
-+ *
-+ * Note that running the skb reallocation in a bottom half opens up
-+ * another can of races which needs to be handled properly. In
-+ * particular it can happen that the interrupt handler tries to run
-+ * the reallocation while the bottom half is either running on another
-+ * CPU or was interrupted on the same CPU. To get around this the
-+ * driver uses bitops to prevent the reallocation routines from being
-+ * reentered.
-+ *
-+ * TX handling can also be done without holding any spin lock, wheee
-+ * this is fun! since tx_csm is only written to by the interrupt
-+ * handler.
-+ */
-+
-+/**
-+ * Threshold values for RX buffer allocation - the low water marks for
-+ * when to start refilling the rings are set to 75% of the ring
-+ * sizes. It seems to make sense to refill the rings entirely from the
-+ * intrrupt handler once it gets below the panic threshold, that way
-+ * we don't risk that the refilling is moved to another CPU when the
-+ * one running the interrupt handler just got the slab code hot in its
-+ * cache.
-+ */
-+#define RX_RING_SIZE AR2313_DESCR_ENTRIES
-+#define RX_PANIC_THRES (RX_RING_SIZE/4)
-+#define RX_LOW_THRES ((3*RX_RING_SIZE)/4)
-+#define CRC_LEN 4
-+#define RX_OFFSET 2
-+
-+#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
-+#define VLAN_HDR 4
-+#else
-+#define VLAN_HDR 0
-+#endif
-+
-+#define AR2313_BUFSIZE (AR2313_MTU + VLAN_HDR + ETH_HLEN + CRC_LEN + \
-+ RX_OFFSET)
-+
-+#ifdef MODULE
-+MODULE_LICENSE("GPL");
-+MODULE_AUTHOR("Sameer Dekate <sdekate@arubanetworks.com>, Imre Kaloz <kaloz@openwrt.org>, Felix Fietkau <nbd@nbd.name>");
-+MODULE_DESCRIPTION("AR231x Ethernet driver");
-+#endif
-+
-+#define virt_to_phys(x) ((u32)(x) & 0x1fffffff)
-+
-+/* prototypes */
-+static void ar231x_halt(struct net_device *dev);
-+static void rx_tasklet_func(unsigned long data);
-+static void rx_tasklet_cleanup(struct net_device *dev);
-+static void ar231x_multicast_list(struct net_device *dev);
-+static void ar231x_tx_timeout(struct net_device *dev);
-+
-+static int ar231x_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum);
-+static int ar231x_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum,
-+ u16 value);
-+static int ar231x_mdiobus_reset(struct mii_bus *bus);
-+static int ar231x_mdiobus_probe(struct net_device *dev);
-+static void ar231x_adjust_link(struct net_device *dev);
-+
-+#ifndef ERR
-+#define ERR(fmt, args...) printk("%s: " fmt, __func__, ##args)
-+#endif
-+
-+#ifdef CONFIG_NET_POLL_CONTROLLER
-+static void
-+ar231x_netpoll(struct net_device *dev)
-+{
-+ unsigned long flags;
-+
-+ local_irq_save(flags);
-+ ar231x_interrupt(dev->irq, dev);
-+ local_irq_restore(flags);
-+}
-+#endif
-+
-+static const struct net_device_ops ar231x_ops = {
-+ .ndo_open = ar231x_open,
-+ .ndo_stop = ar231x_close,
-+ .ndo_start_xmit = ar231x_start_xmit,
-+ .ndo_set_rx_mode = ar231x_multicast_list,
-+ .ndo_do_ioctl = ar231x_ioctl,
-+ .ndo_change_mtu = eth_change_mtu,
-+ .ndo_validate_addr = eth_validate_addr,
-+ .ndo_set_mac_address = eth_mac_addr,
-+ .ndo_tx_timeout = ar231x_tx_timeout,
-+#ifdef CONFIG_NET_POLL_CONTROLLER
-+ .ndo_poll_controller = ar231x_netpoll,
-+#endif
-+};
-+
-+static int ar231x_probe(struct platform_device *pdev)
-+{
-+ struct net_device *dev;
-+ struct ar231x_private *sp;
-+ struct resource *res;
-+ unsigned long ar_eth_base;
-+ char buf[64];
-+
-+ dev = alloc_etherdev(sizeof(struct ar231x_private));
-+
-+ if (dev == NULL) {
-+ printk(KERN_ERR
-+ "ar231x: Unable to allocate net_device structure!\n");
-+ return -ENOMEM;
-+ }
-+
-+ platform_set_drvdata(pdev, dev);
-+
-+ sp = netdev_priv(dev);
-+ sp->dev = dev;
-+ sp->cfg = pdev->dev.platform_data;
-+
-+ sprintf(buf, "eth%d_membase", pdev->id);
-+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, buf);
-+ if (!res)
-+ return -ENODEV;
-+
-+ sp->link = 0;
-+ ar_eth_base = res->start;
-+
-+ sprintf(buf, "eth%d_irq", pdev->id);
-+ dev->irq = platform_get_irq_byname(pdev, buf);
-+
-+ spin_lock_init(&sp->lock);
-+
-+ dev->features |= NETIF_F_HIGHDMA;
-+ dev->netdev_ops = &ar231x_ops;
-+
-+ tasklet_init(&sp->rx_tasklet, rx_tasklet_func, (unsigned long)dev);
-+ tasklet_disable(&sp->rx_tasklet);
-+
-+ sp->eth_regs = ioremap_nocache(ar_eth_base, sizeof(*sp->eth_regs));
-+ if (!sp->eth_regs) {
-+ printk("Can't remap eth registers\n");
-+ return -ENXIO;
-+ }
-+
-+ /**
-+ * When there's only one MAC, PHY regs are typically on ENET0,
-+ * even though the MAC might be on ENET1.
-+ * So remap PHY regs separately.
-+ */
-+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "eth0_mii");
-+ if (!res) {
-+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
-+ "eth1_mii");
-+ if (!res)
-+ return -ENODEV;
-+ }
-+ sp->phy_regs = ioremap_nocache(res->start, resource_size(res));
-+ if (!sp->phy_regs) {
-+ printk("Can't remap phy registers\n");
-+ return -ENXIO;
-+ }
-+
-+ sp->dma_regs = ioremap_nocache(ar_eth_base + 0x1000,
-+ sizeof(*sp->dma_regs));
-+ if (!sp->dma_regs) {
-+ printk("Can't remap DMA registers\n");
-+ return -ENXIO;
-+ }
-+ dev->base_addr = ar_eth_base + 0x1000;
-+
-+ strncpy(sp->name, "Atheros AR231x", sizeof(sp->name) - 1);
-+ sp->name[sizeof(sp->name) - 1] = '\0';
-+ memcpy(dev->dev_addr, sp->cfg->macaddr, 6);
-+
-+ if (ar231x_init(dev)) {
-+ /* ar231x_init() calls ar231x_init_cleanup() on error */
-+ kfree(dev);
-+ return -ENODEV;
-+ }
-+
-+ if (register_netdev(dev)) {
-+ printk("%s: register_netdev failed\n", __func__);
-+ return -1;
-+ }
-+
-+ printk("%s: %s: %pM, irq %d\n", dev->name, sp->name, dev->dev_addr,
-+ dev->irq);
-+
-+ sp->mii_bus = mdiobus_alloc();
-+ if (sp->mii_bus == NULL)
-+ return -1;
-+
-+ sp->mii_bus->priv = dev;
-+ sp->mii_bus->read = ar231x_mdiobus_read;
-+ sp->mii_bus->write = ar231x_mdiobus_write;
-+ sp->mii_bus->reset = ar231x_mdiobus_reset;
-+ sp->mii_bus->name = "ar231x_eth_mii";
-+ snprintf(sp->mii_bus->id, MII_BUS_ID_SIZE, "%d", pdev->id);
-+ sp->mii_bus->irq = kmalloc(sizeof(int), GFP_KERNEL);
-+ *sp->mii_bus->irq = PHY_POLL;
-+
-+ mdiobus_register(sp->mii_bus);
-+
-+ if (ar231x_mdiobus_probe(dev) != 0) {
-+ printk(KERN_ERR "%s: mdiobus_probe failed\n", dev->name);
-+ rx_tasklet_cleanup(dev);
-+ ar231x_init_cleanup(dev);
-+ unregister_netdev(dev);
-+ kfree(dev);
-+ return -ENODEV;
-+ }
-+
-+ /* start link poll timer */
-+ ar231x_setup_timer(dev);
-+
-+ return 0;
-+}
-+
-+static void ar231x_multicast_list(struct net_device *dev)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+ unsigned int filter;
-+
-+ filter = sp->eth_regs->mac_control;
-+
-+ if (dev->flags & IFF_PROMISC)
-+ filter |= MAC_CONTROL_PR;
-+ else
-+ filter &= ~MAC_CONTROL_PR;
-+ if ((dev->flags & IFF_ALLMULTI) || (netdev_mc_count(dev) > 0))
-+ filter |= MAC_CONTROL_PM;
-+ else
-+ filter &= ~MAC_CONTROL_PM;
-+
-+ sp->eth_regs->mac_control = filter;
-+}
-+
-+static void rx_tasklet_cleanup(struct net_device *dev)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+
-+ /**
-+ * Tasklet may be scheduled. Need to get it removed from the list
-+ * since we're about to free the struct.
-+ */
-+
-+ sp->unloading = 1;
-+ tasklet_enable(&sp->rx_tasklet);
-+ tasklet_kill(&sp->rx_tasklet);
-+}
-+
-+static int ar231x_remove(struct platform_device *pdev)
-+{
-+ struct net_device *dev = platform_get_drvdata(pdev);
-+ struct ar231x_private *sp = netdev_priv(dev);
-+
-+ rx_tasklet_cleanup(dev);
-+ ar231x_init_cleanup(dev);
-+ unregister_netdev(dev);
-+ mdiobus_unregister(sp->mii_bus);
-+ mdiobus_free(sp->mii_bus);
-+ kfree(dev);
-+ return 0;
-+}
-+
-+/**
-+ * Restart the AR2313 ethernet controller.
-+ */
-+static int ar231x_restart(struct net_device *dev)
-+{
-+ /* disable interrupts */
-+ disable_irq(dev->irq);
-+
-+ /* stop mac */
-+ ar231x_halt(dev);
-+
-+ /* initialize */
-+ ar231x_init(dev);
-+
-+ /* enable interrupts */
-+ enable_irq(dev->irq);
-+
-+ return 0;
-+}
-+
-+static struct platform_driver ar231x_driver = {
-+ .driver.name = "ar231x-eth",
-+ .probe = ar231x_probe,
-+ .remove = ar231x_remove,
-+};
-+
-+module_platform_driver(ar231x_driver);
-+
-+static void ar231x_free_descriptors(struct net_device *dev)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+
-+ if (sp->rx_ring != NULL) {
-+ kfree((void *)KSEG0ADDR(sp->rx_ring));
-+ sp->rx_ring = NULL;
-+ sp->tx_ring = NULL;
-+ }
-+}
-+
-+static int ar231x_allocate_descriptors(struct net_device *dev)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+ int size;
-+ int j;
-+ ar231x_descr_t *space;
-+
-+ if (sp->rx_ring != NULL) {
-+ printk("%s: already done.\n", __func__);
-+ return 0;
-+ }
-+
-+ size = sizeof(ar231x_descr_t) * (AR2313_DESCR_ENTRIES * AR2313_QUEUES);
-+ space = kmalloc(size, GFP_KERNEL);
-+ if (space == NULL)
-+ return 1;
-+
-+ /* invalidate caches */
-+ dma_cache_inv((unsigned int)space, size);
-+
-+ /* now convert pointer to KSEG1 */
-+ space = (ar231x_descr_t *)KSEG1ADDR(space);
-+
-+ memset((void *)space, 0, size);
-+
-+ sp->rx_ring = space;
-+ space += AR2313_DESCR_ENTRIES;
-+
-+ sp->tx_ring = space;
-+ space += AR2313_DESCR_ENTRIES;
-+
-+ /* Initialize the transmit Descriptors */
-+ for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
-+ ar231x_descr_t *td = &sp->tx_ring[j];
-+
-+ td->status = 0;
-+ td->devcs = DMA_TX1_CHAINED;
-+ td->addr = 0;
-+ td->descr = virt_to_phys(&sp->tx_ring[DSC_NEXT(j)]);
-+ }
-+
-+ return 0;
-+}
-+
-+/**
-+ * Generic cleanup handling data allocated during init. Used when the
-+ * module is unloaded or if an error occurs during initialization
-+ */
-+static void ar231x_init_cleanup(struct net_device *dev)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+ struct sk_buff *skb;
-+ int j;
-+
-+ ar231x_free_descriptors(dev);
-+
-+ if (sp->eth_regs)
-+ iounmap((void *)sp->eth_regs);
-+ if (sp->dma_regs)
-+ iounmap((void *)sp->dma_regs);
-+ if (sp->phy_regs)
-+ iounmap((void *)sp->phy_regs);
-+
-+ if (sp->rx_skb) {
-+ for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
-+ skb = sp->rx_skb[j];
-+ if (skb) {
-+ sp->rx_skb[j] = NULL;
-+ dev_kfree_skb(skb);
-+ }
-+ }
-+ kfree(sp->rx_skb);
-+ sp->rx_skb = NULL;
-+ }
-+
-+ if (sp->tx_skb) {
-+ for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
-+ skb = sp->tx_skb[j];
-+ if (skb) {
-+ sp->tx_skb[j] = NULL;
-+ dev_kfree_skb(skb);
-+ }
-+ }
-+ kfree(sp->tx_skb);
-+ sp->tx_skb = NULL;
-+ }
-+}
-+
-+static int ar231x_setup_timer(struct net_device *dev)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+
-+ init_timer(&sp->link_timer);
-+
-+ sp->link_timer.function = ar231x_link_timer_fn;
-+ sp->link_timer.data = (int)dev;
-+ sp->link_timer.expires = jiffies + HZ;
-+
-+ add_timer(&sp->link_timer);
-+ return 0;
-+}
-+
-+static void ar231x_link_timer_fn(unsigned long data)
-+{
-+ struct net_device *dev = (struct net_device *)data;
-+ struct ar231x_private *sp = netdev_priv(dev);
-+
-+ /**
-+ * See if the link status changed.
-+ * This was needed to make sure we set the PHY to the
-+ * autonegotiated value of half or full duplex.
-+ */
-+ ar231x_check_link(dev);
-+
-+ /**
-+ * Loop faster when we don't have link.
-+ * This was needed to speed up the AP bootstrap time.
-+ */
-+ if (sp->link == 0)
-+ mod_timer(&sp->link_timer, jiffies + HZ / 2);
-+ else
-+ mod_timer(&sp->link_timer, jiffies + LINK_TIMER);
-+}
-+
-+static void ar231x_check_link(struct net_device *dev)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+ u16 phy_data;
-+
-+ phy_data = ar231x_mdiobus_read(sp->mii_bus, sp->phy, MII_BMSR);
-+ if (sp->phy_data != phy_data) {
-+ if (phy_data & BMSR_LSTATUS) {
-+ /**
-+ * Link is present, ready link partner ability to
-+ * deterine duplexity.
-+ */
-+ int duplex = 0;
-+ u16 reg;
-+
-+ sp->link = 1;
-+ reg = ar231x_mdiobus_read(sp->mii_bus, sp->phy,
-+ MII_BMCR);
-+ if (reg & BMCR_ANENABLE) {
-+ /* auto neg enabled */
-+ reg = ar231x_mdiobus_read(sp->mii_bus, sp->phy,
-+ MII_LPA);
-+ duplex = reg & (LPA_100FULL | LPA_10FULL) ?
-+ 1 : 0;
-+ } else {
-+ /* no auto neg, just read duplex config */
-+ duplex = (reg & BMCR_FULLDPLX) ? 1 : 0;
-+ }
-+
-+ printk(KERN_INFO "%s: Configuring MAC for %s duplex\n",
-+ dev->name, (duplex) ? "full" : "half");
-+
-+ if (duplex) {
-+ /* full duplex */
-+ sp->eth_regs->mac_control =
-+ (sp->eth_regs->mac_control |
-+ MAC_CONTROL_F) & ~MAC_CONTROL_DRO;
-+ } else {
-+ /* half duplex */
-+ sp->eth_regs->mac_control =
-+ (sp->eth_regs->mac_control |
-+ MAC_CONTROL_DRO) & ~MAC_CONTROL_F;
-+ }
-+ } else {
-+ /* no link */
-+ sp->link = 0;
-+ }
-+ sp->phy_data = phy_data;
-+ }
-+}
-+
-+static int ar231x_reset_reg(struct net_device *dev)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+ unsigned int ethsal, ethsah;
-+ unsigned int flags;
-+
-+ sp->cfg->reset_set(sp->cfg->reset_mac);
-+ mdelay(10);
-+ sp->cfg->reset_clear(sp->cfg->reset_mac);
-+ mdelay(10);
-+ sp->cfg->reset_set(sp->cfg->reset_phy);
-+ mdelay(10);
-+ sp->cfg->reset_clear(sp->cfg->reset_phy);
-+ mdelay(10);
-+
-+ sp->dma_regs->bus_mode = (DMA_BUS_MODE_SWR);
-+ mdelay(10);
-+ sp->dma_regs->bus_mode =
-+ ((32 << DMA_BUS_MODE_PBL_SHIFT) | DMA_BUS_MODE_BLE);
-+
-+ /* enable interrupts */
-+ sp->dma_regs->intr_ena = DMA_STATUS_AIS | DMA_STATUS_NIS |
-+ DMA_STATUS_RI | DMA_STATUS_TI |
-+ DMA_STATUS_FBE;
-+ sp->dma_regs->xmt_base = virt_to_phys(sp->tx_ring);
-+ sp->dma_regs->rcv_base = virt_to_phys(sp->rx_ring);
-+ sp->dma_regs->control =
-+ (DMA_CONTROL_SR | DMA_CONTROL_ST | DMA_CONTROL_SF);
-+
-+ sp->eth_regs->flow_control = (FLOW_CONTROL_FCE);
-+ sp->eth_regs->vlan_tag = (0x8100);
-+
-+ /* Enable Ethernet Interface */
-+ flags = (MAC_CONTROL_TE | /* transmit enable */
-+ MAC_CONTROL_PM | /* pass mcast */
-+ MAC_CONTROL_F | /* full duplex */
-+ MAC_CONTROL_HBD); /* heart beat disabled */
-+
-+ if (dev->flags & IFF_PROMISC) { /* set promiscuous mode */
-+ flags |= MAC_CONTROL_PR;
-+ }
-+ sp->eth_regs->mac_control = flags;
-+
-+ /* Set all Ethernet station address registers to their initial values */
-+ ethsah = (((u_int) (dev->dev_addr[5]) << 8) & (u_int) 0x0000FF00) |
-+ (((u_int) (dev->dev_addr[4]) << 0) & (u_int) 0x000000FF);
-+
-+ ethsal = (((u_int) (dev->dev_addr[3]) << 24) & (u_int) 0xFF000000) |
-+ (((u_int) (dev->dev_addr[2]) << 16) & (u_int) 0x00FF0000) |
-+ (((u_int) (dev->dev_addr[1]) << 8) & (u_int) 0x0000FF00) |
-+ (((u_int) (dev->dev_addr[0]) << 0) & (u_int) 0x000000FF);
-+
-+ sp->eth_regs->mac_addr[0] = ethsah;
-+ sp->eth_regs->mac_addr[1] = ethsal;
-+
-+ mdelay(10);
-+
-+ return 0;
-+}
-+
-+static int ar231x_init(struct net_device *dev)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+ int ecode = 0;
-+
-+ /* Allocate descriptors */
-+ if (ar231x_allocate_descriptors(dev)) {
-+ printk("%s: %s: ar231x_allocate_descriptors failed\n",
-+ dev->name, __func__);
-+ ecode = -EAGAIN;
-+ goto init_error;
-+ }
-+
-+ /* Get the memory for the skb rings */
-+ if (sp->rx_skb == NULL) {
-+ sp->rx_skb =
-+ kmalloc(sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES,
-+ GFP_KERNEL);
-+ if (!(sp->rx_skb)) {
-+ printk("%s: %s: rx_skb kmalloc failed\n",
-+ dev->name, __func__);
-+ ecode = -EAGAIN;
-+ goto init_error;
-+ }
-+ }
-+ memset(sp->rx_skb, 0, sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES);
-+
-+ if (sp->tx_skb == NULL) {
-+ sp->tx_skb =
-+ kmalloc(sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES,
-+ GFP_KERNEL);
-+ if (!(sp->tx_skb)) {
-+ printk("%s: %s: tx_skb kmalloc failed\n",
-+ dev->name, __func__);
-+ ecode = -EAGAIN;
-+ goto init_error;
-+ }
-+ }
-+ memset(sp->tx_skb, 0, sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES);
-+
-+ /**
-+ * Set tx_csm before we start receiving interrupts, otherwise
-+ * the interrupt handler might think it is supposed to process
-+ * tx ints before we are up and running, which may cause a null
-+ * pointer access in the int handler.
-+ */
-+ sp->rx_skbprd = 0;
-+ sp->cur_rx = 0;
-+ sp->tx_prd = 0;
-+ sp->tx_csm = 0;
-+
-+ /* Zero the stats before starting the interface */
-+ memset(&dev->stats, 0, sizeof(dev->stats));
-+
-+ /**
-+ * We load the ring here as there seem to be no way to tell the
-+ * firmware to wipe the ring without re-initializing it.
-+ */
-+ ar231x_load_rx_ring(dev, RX_RING_SIZE);
-+
-+ /* Init hardware */
-+ ar231x_reset_reg(dev);
-+
-+ /* Get the IRQ */
-+ ecode = request_irq(dev->irq, &ar231x_interrupt, 0,
-+ dev->name, dev);
-+ if (ecode) {
-+ printk(KERN_WARNING "%s: %s: Requested IRQ %d is busy\n",
-+ dev->name, __func__, dev->irq);
-+ goto init_error;
-+ }
-+
-+ tasklet_enable(&sp->rx_tasklet);
-+
-+ return 0;
-+
-+init_error:
-+ ar231x_init_cleanup(dev);
-+ return ecode;
-+}
-+
-+/**
-+ * Load the rx ring.
-+ *
-+ * Loading rings is safe without holding the spin lock since this is
-+ * done only before the device is enabled, thus no interrupts are
-+ * generated and by the interrupt handler/tasklet handler.
-+ */
-+static void ar231x_load_rx_ring(struct net_device *dev, int nr_bufs)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+ short i, idx;
-+
-+ idx = sp->rx_skbprd;
-+
-+ for (i = 0; i < nr_bufs; i++) {
-+ struct sk_buff *skb;
-+ ar231x_descr_t *rd;
-+
-+ if (sp->rx_skb[idx])
-+ break;
-+
-+ skb = netdev_alloc_skb_ip_align(dev, AR2313_BUFSIZE);
-+ if (!skb) {
-+ printk("\n\n\n\n %s: No memory in system\n\n\n\n",
-+ __func__);
-+ break;
-+ }
-+
-+ /* Make sure IP header starts on a fresh cache line */
-+ skb->dev = dev;
-+ sp->rx_skb[idx] = skb;
-+
-+ rd = (ar231x_descr_t *)&sp->rx_ring[idx];
-+
-+ /* initialize dma descriptor */
-+ rd->devcs = ((AR2313_BUFSIZE << DMA_RX1_BSIZE_SHIFT) |
-+ DMA_RX1_CHAINED);
-+ rd->addr = virt_to_phys(skb->data);
-+ rd->descr = virt_to_phys(&sp->rx_ring[DSC_NEXT(idx)]);
-+ rd->status = DMA_RX_OWN;
-+
-+ idx = DSC_NEXT(idx);
-+ }
-+
-+ if (i)
-+ sp->rx_skbprd = idx;
-+}
-+
-+#define AR2313_MAX_PKTS_PER_CALL 64
-+
-+static int ar231x_rx_int(struct net_device *dev)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+ struct sk_buff *skb, *skb_new;
-+ ar231x_descr_t *rxdesc;
-+ unsigned int status;
-+ u32 idx;
-+ int pkts = 0;
-+ int rval;
-+
-+ idx = sp->cur_rx;
-+
-+ /* process at most the entire ring and then wait for another int */
-+ while (1) {
-+ rxdesc = &sp->rx_ring[idx];
-+ status = rxdesc->status;
-+
-+ if (status & DMA_RX_OWN) {
-+ /* SiByte owns descriptor or descr not yet filled in */
-+ rval = 0;
-+ break;
-+ }
-+
-+ if (++pkts > AR2313_MAX_PKTS_PER_CALL) {
-+ rval = 1;
-+ break;
-+ }
-+
-+ if ((status & DMA_RX_ERROR) && !(status & DMA_RX_LONG)) {
-+ dev->stats.rx_errors++;
-+ dev->stats.rx_dropped++;
-+
-+ /* add statistics counters */
-+ if (status & DMA_RX_ERR_CRC)
-+ dev->stats.rx_crc_errors++;
-+ if (status & DMA_RX_ERR_COL)
-+ dev->stats.rx_over_errors++;
-+ if (status & DMA_RX_ERR_LENGTH)
-+ dev->stats.rx_length_errors++;
-+ if (status & DMA_RX_ERR_RUNT)
-+ dev->stats.rx_over_errors++;
-+ if (status & DMA_RX_ERR_DESC)
-+ dev->stats.rx_over_errors++;
-+
-+ } else {
-+ /* alloc new buffer. */
-+ skb_new = netdev_alloc_skb_ip_align(dev,
-+ AR2313_BUFSIZE);
-+ if (skb_new != NULL) {
-+ skb = sp->rx_skb[idx];
-+ /* set skb */
-+ skb_put(skb, ((status >> DMA_RX_LEN_SHIFT) &
-+ 0x3fff) - CRC_LEN);
-+
-+ dev->stats.rx_bytes += skb->len;
-+ skb->protocol = eth_type_trans(skb, dev);
-+ /* pass the packet to upper layers */
-+ netif_rx(skb);
-+
-+ skb_new->dev = dev;
-+ /* reset descriptor's curr_addr */
-+ rxdesc->addr = virt_to_phys(skb_new->data);
-+
-+ dev->stats.rx_packets++;
-+ sp->rx_skb[idx] = skb_new;
-+ } else {
-+ dev->stats.rx_dropped++;
-+ }
-+ }
-+
-+ rxdesc->devcs = ((AR2313_BUFSIZE << DMA_RX1_BSIZE_SHIFT) |
-+ DMA_RX1_CHAINED);
-+ rxdesc->status = DMA_RX_OWN;
-+
-+ idx = DSC_NEXT(idx);
-+ }
-+
-+ sp->cur_rx = idx;
-+
-+ return rval;
-+}
-+
-+static void ar231x_tx_int(struct net_device *dev)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+ u32 idx;
-+ struct sk_buff *skb;
-+ ar231x_descr_t *txdesc;
-+ unsigned int status = 0;
-+
-+ idx = sp->tx_csm;
-+
-+ while (idx != sp->tx_prd) {
-+ txdesc = &sp->tx_ring[idx];
-+ status = txdesc->status;
-+
-+ if (status & DMA_TX_OWN) {
-+ /* ar231x dma still owns descr */
-+ break;
-+ }
-+ /* done with this descriptor */
-+ dma_unmap_single(NULL, txdesc->addr,
-+ txdesc->devcs & DMA_TX1_BSIZE_MASK,
-+ DMA_TO_DEVICE);
-+ txdesc->status = 0;
-+
-+ if (status & DMA_TX_ERROR) {
-+ dev->stats.tx_errors++;
-+ dev->stats.tx_dropped++;
-+ if (status & DMA_TX_ERR_UNDER)
-+ dev->stats.tx_fifo_errors++;
-+ if (status & DMA_TX_ERR_HB)
-+ dev->stats.tx_heartbeat_errors++;
-+ if (status & (DMA_TX_ERR_LOSS | DMA_TX_ERR_LINK))
-+ dev->stats.tx_carrier_errors++;
-+ if (status & (DMA_TX_ERR_LATE | DMA_TX_ERR_COL |
-+ DMA_TX_ERR_JABBER | DMA_TX_ERR_DEFER))
-+ dev->stats.tx_aborted_errors++;
-+ } else {
-+ /* transmit OK */
-+ dev->stats.tx_packets++;
-+ }
-+
-+ skb = sp->tx_skb[idx];
-+ sp->tx_skb[idx] = NULL;
-+ idx = DSC_NEXT(idx);
-+ dev->stats.tx_bytes += skb->len;
-+ dev_kfree_skb_irq(skb);
-+ }
-+
-+ sp->tx_csm = idx;
-+}
-+
-+static void rx_tasklet_func(unsigned long data)
-+{
-+ struct net_device *dev = (struct net_device *)data;
-+ struct ar231x_private *sp = netdev_priv(dev);
-+
-+ if (sp->unloading)
-+ return;
-+
-+ if (ar231x_rx_int(dev)) {
-+ tasklet_hi_schedule(&sp->rx_tasklet);
-+ } else {
-+ unsigned long flags;
-+
-+ spin_lock_irqsave(&sp->lock, flags);
-+ sp->dma_regs->intr_ena |= DMA_STATUS_RI;
-+ spin_unlock_irqrestore(&sp->lock, flags);
-+ }
-+}
-+
-+static void rx_schedule(struct net_device *dev)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+
-+ sp->dma_regs->intr_ena &= ~DMA_STATUS_RI;
-+
-+ tasklet_hi_schedule(&sp->rx_tasklet);
-+}
-+
-+static irqreturn_t ar231x_interrupt(int irq, void *dev_id)
-+{
-+ struct net_device *dev = (struct net_device *)dev_id;
-+ struct ar231x_private *sp = netdev_priv(dev);
-+ unsigned int status, enabled;
-+
-+ /* clear interrupt */
-+ /* Don't clear RI bit if currently disabled */
-+ status = sp->dma_regs->status;
-+ enabled = sp->dma_regs->intr_ena;
-+ sp->dma_regs->status = status & enabled;
-+
-+ if (status & DMA_STATUS_NIS) {
-+ /* normal status */
-+ /**
-+ * Don't schedule rx processing if interrupt
-+ * is already disabled.
-+ */
-+ if (status & enabled & DMA_STATUS_RI) {
-+ /* receive interrupt */
-+ rx_schedule(dev);
-+ }
-+ if (status & DMA_STATUS_TI) {
-+ /* transmit interrupt */
-+ ar231x_tx_int(dev);
-+ }
-+ }
-+
-+ /* abnormal status */
-+ if (status & (DMA_STATUS_FBE | DMA_STATUS_TPS))
-+ ar231x_restart(dev);
-+
-+ return IRQ_HANDLED;
-+}
-+
-+static int ar231x_open(struct net_device *dev)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+ unsigned int ethsal, ethsah;
-+
-+ /* reset the hardware, in case the MAC address changed */
-+ ethsah = (((u_int) (dev->dev_addr[5]) << 8) & (u_int) 0x0000FF00) |
-+ (((u_int) (dev->dev_addr[4]) << 0) & (u_int) 0x000000FF);
-+
-+ ethsal = (((u_int) (dev->dev_addr[3]) << 24) & (u_int) 0xFF000000) |
-+ (((u_int) (dev->dev_addr[2]) << 16) & (u_int) 0x00FF0000) |
-+ (((u_int) (dev->dev_addr[1]) << 8) & (u_int) 0x0000FF00) |
-+ (((u_int) (dev->dev_addr[0]) << 0) & (u_int) 0x000000FF);
-+
-+ sp->eth_regs->mac_addr[0] = ethsah;
-+ sp->eth_regs->mac_addr[1] = ethsal;
-+
-+ mdelay(10);
-+
-+ dev->mtu = 1500;
-+ netif_start_queue(dev);
-+
-+ sp->eth_regs->mac_control |= MAC_CONTROL_RE;
-+
-+ return 0;
-+}
-+
-+static void ar231x_tx_timeout(struct net_device *dev)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+ unsigned long flags;
-+
-+ spin_lock_irqsave(&sp->lock, flags);
-+ ar231x_restart(dev);
-+ spin_unlock_irqrestore(&sp->lock, flags);
-+}
-+
-+static void ar231x_halt(struct net_device *dev)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+ int j;
-+
-+ tasklet_disable(&sp->rx_tasklet);
-+
-+ /* kill the MAC */
-+ sp->eth_regs->mac_control &= ~(MAC_CONTROL_RE | /* disable Receives */
-+ MAC_CONTROL_TE); /* disable Transmits */
-+ /* stop dma */
-+ sp->dma_regs->control = 0;
-+ sp->dma_regs->bus_mode = DMA_BUS_MODE_SWR;
-+
-+ /* place phy and MAC in reset */
-+ sp->cfg->reset_set(sp->cfg->reset_mac);
-+ sp->cfg->reset_set(sp->cfg->reset_phy);
-+
-+ /* free buffers on tx ring */
-+ for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
-+ struct sk_buff *skb;
-+ ar231x_descr_t *txdesc;
-+
-+ txdesc = &sp->tx_ring[j];
-+ txdesc->descr = 0;
-+
-+ skb = sp->tx_skb[j];
-+ if (skb) {
-+ dev_kfree_skb(skb);
-+ sp->tx_skb[j] = NULL;
-+ }
-+ }
-+}
-+
-+/**
-+ * close should do nothing. Here's why. It's called when
-+ * 'ifconfig bond0 down' is run. If it calls free_irq then
-+ * the irq is gone forever ! When bond0 is made 'up' again,
-+ * the ar231x_open () does not call request_irq (). Worse,
-+ * the call to ar231x_halt() generates a WDOG reset due to
-+ * the write to reset register and the box reboots.
-+ * Commenting this out is good since it allows the
-+ * system to resume when bond0 is made up again.
-+ */
-+static int ar231x_close(struct net_device *dev)
-+{
-+#if 0
-+ /* Disable interrupts */
-+ disable_irq(dev->irq);
-+
-+ /**
-+ * Without (or before) releasing irq and stopping hardware, this
-+ * is an absolute non-sense, by the way. It will be reset instantly
-+ * by the first irq.
-+ */
-+ netif_stop_queue(dev);
-+
-+ /* stop the MAC and DMA engines */
-+ ar231x_halt(dev);
-+
-+ /* release the interrupt */
-+ free_irq(dev->irq, dev);
-+
-+#endif
-+ return 0;
-+}
-+
-+static int ar231x_start_xmit(struct sk_buff *skb, struct net_device *dev)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+ ar231x_descr_t *td;
-+ u32 idx;
-+
-+ idx = sp->tx_prd;
-+ td = &sp->tx_ring[idx];
-+
-+ if (td->status & DMA_TX_OWN) {
-+ /* free skbuf and lie to the caller that we sent it out */
-+ dev->stats.tx_dropped++;
-+ dev_kfree_skb(skb);
-+
-+ /* restart transmitter in case locked */
-+ sp->dma_regs->xmt_poll = 0;
-+ return 0;
-+ }
-+
-+ /* Setup the transmit descriptor. */
-+ td->devcs = ((skb->len << DMA_TX1_BSIZE_SHIFT) |
-+ (DMA_TX1_LS | DMA_TX1_IC | DMA_TX1_CHAINED));
-+ td->addr = dma_map_single(NULL, skb->data, skb->len, DMA_TO_DEVICE);
-+ td->status = DMA_TX_OWN;
-+
-+ /* kick transmitter last */
-+ sp->dma_regs->xmt_poll = 0;
-+
-+ sp->tx_skb[idx] = skb;
-+ idx = DSC_NEXT(idx);
-+ sp->tx_prd = idx;
-+
-+ return 0;
-+}
-+
-+static int ar231x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+
-+ switch (cmd) {
-+ case SIOCGMIIPHY:
-+ case SIOCGMIIREG:
-+ case SIOCSMIIREG:
-+ return phy_mii_ioctl(sp->phy_dev, ifr, cmd);
-+
-+ default:
-+ break;
-+ }
-+
-+ return -EOPNOTSUPP;
-+}
-+
-+static void ar231x_adjust_link(struct net_device *dev)
-+{
-+ struct ar231x_private *sp = netdev_priv(dev);
-+ unsigned int mc;
-+
-+ if (!sp->phy_dev->link)
-+ return;
-+
-+ if (sp->phy_dev->duplex != sp->oldduplex) {
-+ mc = readl(&sp->eth_regs->mac_control);
-+ mc &= ~(MAC_CONTROL_F | MAC_CONTROL_DRO);
-+ if (sp->phy_dev->duplex)
-+ mc |= MAC_CONTROL_F;
-+ else
-+ mc |= MAC_CONTROL_DRO;
-+ writel(mc, &sp->eth_regs->mac_control);
-+ sp->oldduplex = sp->phy_dev->duplex;
-+ }
-+}
-+
-+#define MII_ADDR(phy, reg) \
-+ ((reg << MII_ADDR_REG_SHIFT) | (phy << MII_ADDR_PHY_SHIFT))
-+
-+static int
-+ar231x_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum)
-+{
-+ struct net_device *const dev = bus->priv;
-+ struct ar231x_private *sp = netdev_priv(dev);
-+ volatile MII *ethernet = sp->phy_regs;
-+
-+ ethernet->mii_addr = MII_ADDR(phy_addr, regnum);
-+ while (ethernet->mii_addr & MII_ADDR_BUSY)
-+ ;
-+ return ethernet->mii_data >> MII_DATA_SHIFT;
-+}
-+
-+static int
-+ar231x_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum, u16 value)
-+{
-+ struct net_device *const dev = bus->priv;
-+ struct ar231x_private *sp = netdev_priv(dev);
-+ volatile MII *ethernet = sp->phy_regs;
-+
-+ while (ethernet->mii_addr & MII_ADDR_BUSY)
-+ ;
-+ ethernet->mii_data = value << MII_DATA_SHIFT;
-+ ethernet->mii_addr = MII_ADDR(phy_addr, regnum) | MII_ADDR_WRITE;
-+
-+ return 0;
-+}
-+
-+static int ar231x_mdiobus_reset(struct mii_bus *bus)
-+{
-+ struct net_device *const dev = bus->priv;
-+
-+ ar231x_reset_reg(dev);
-+
-+ return 0;
-+}
-+
-+static int ar231x_mdiobus_probe(struct net_device *dev)
-+{
-+ struct ar231x_private *const sp = netdev_priv(dev);
-+ struct phy_device *phydev = NULL;
-+ int phy_addr;
-+
-+ /* find the first (lowest address) PHY on the current MAC's MII bus */
-+ for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++)
-+ if (sp->mii_bus->phy_map[phy_addr]) {
-+ phydev = sp->mii_bus->phy_map[phy_addr];
-+ sp->phy = phy_addr;
-+ break; /* break out with first one found */
-+ }
-+
-+ if (!phydev) {
-+ printk(KERN_ERR "ar231x: %s: no PHY found\n", dev->name);
-+ return -1;
-+ }
-+
-+ /* now we are supposed to have a proper phydev, to attach to... */
-+ BUG_ON(!phydev);
-+ BUG_ON(phydev->attached_dev);
-+
-+ phydev = phy_connect(dev, dev_name(&phydev->dev), &ar231x_adjust_link,
-+ PHY_INTERFACE_MODE_MII);
-+
-+ if (IS_ERR(phydev)) {
-+ printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
-+ return PTR_ERR(phydev);
-+ }
-+
-+ /* mask with MAC supported features */
-+ phydev->supported &= (SUPPORTED_10baseT_Half
-+ | SUPPORTED_10baseT_Full
-+ | SUPPORTED_100baseT_Half
-+ | SUPPORTED_100baseT_Full
-+ | SUPPORTED_Autoneg
-+ /* | SUPPORTED_Pause | SUPPORTED_Asym_Pause */
-+ | SUPPORTED_MII
-+ | SUPPORTED_TP);
-+
-+ phydev->advertising = phydev->supported;
-+
-+ sp->oldduplex = -1;
-+ sp->phy_dev = phydev;
-+
-+ printk(KERN_INFO "%s: attached PHY driver [%s] (mii_bus:phy_addr=%s)\n",
-+ dev->name, phydev->drv->name, dev_name(&phydev->dev));
-+
-+ return 0;
-+}
-+
---- /dev/null
-+++ b/drivers/net/ethernet/atheros/ar231x/ar231x.h
-@@ -0,0 +1,288 @@
-+/*
-+ * ar231x.h: Linux driver for the Atheros AR231x Ethernet device.
-+ *
-+ * Copyright (C) 2004 by Sameer Dekate <sdekate@arubanetworks.com>
-+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006-2009 Felix Fietkau <nbd@nbd.name>
-+ *
-+ * Thanks to Atheros for providing hardware and documentation
-+ * enabling me to write this driver.
-+ *
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ */
-+
-+#ifndef _AR2313_H_
-+#define _AR2313_H_
-+
-+#include <linux/interrupt.h>
-+#include <generated/autoconf.h>
-+#include <linux/bitops.h>
-+#include <ath25_platform.h>
-+
-+/* probe link timer - 5 secs */
-+#define LINK_TIMER (5*HZ)
-+
-+#define IS_DMA_TX_INT(X) (((X) & (DMA_STATUS_TI)) != 0)
-+#define IS_DMA_RX_INT(X) (((X) & (DMA_STATUS_RI)) != 0)
-+#define IS_DRIVER_OWNED(X) (((X) & (DMA_TX_OWN)) == 0)
-+
-+#define AR2313_TX_TIMEOUT (HZ/4)
-+
-+/* Rings */
-+#define DSC_RING_ENTRIES_SIZE (AR2313_DESCR_ENTRIES * sizeof(struct desc))
-+#define DSC_NEXT(idx) ((idx + 1) & (AR2313_DESCR_ENTRIES - 1))
-+
-+#define AR2313_MBGET 2
-+#define AR2313_MBSET 3
-+#define AR2313_PCI_RECONFIG 4
-+#define AR2313_PCI_DUMP 5
-+#define AR2313_TEST_PANIC 6
-+#define AR2313_TEST_NULLPTR 7
-+#define AR2313_READ_DATA 8
-+#define AR2313_WRITE_DATA 9
-+#define AR2313_GET_VERSION 10
-+#define AR2313_TEST_HANG 11
-+#define AR2313_SYNC 12
-+
-+#define DMA_RX_ERR_CRC BIT(1)
-+#define DMA_RX_ERR_DRIB BIT(2)
-+#define DMA_RX_ERR_MII BIT(3)
-+#define DMA_RX_EV2 BIT(5)
-+#define DMA_RX_ERR_COL BIT(6)
-+#define DMA_RX_LONG BIT(7)
-+#define DMA_RX_LS BIT(8) /* last descriptor */
-+#define DMA_RX_FS BIT(9) /* first descriptor */
-+#define DMA_RX_MF BIT(10) /* multicast frame */
-+#define DMA_RX_ERR_RUNT BIT(11) /* runt frame */
-+#define DMA_RX_ERR_LENGTH BIT(12) /* length error */
-+#define DMA_RX_ERR_DESC BIT(14) /* descriptor error */
-+#define DMA_RX_ERROR BIT(15) /* error summary */
-+#define DMA_RX_LEN_MASK 0x3fff0000
-+#define DMA_RX_LEN_SHIFT 16
-+#define DMA_RX_FILT BIT(30)
-+#define DMA_RX_OWN BIT(31) /* desc owned by DMA controller */
-+
-+#define DMA_RX1_BSIZE_MASK 0x000007ff
-+#define DMA_RX1_BSIZE_SHIFT 0
-+#define DMA_RX1_CHAINED BIT(24)
-+#define DMA_RX1_RER BIT(25)
-+
-+#define DMA_TX_ERR_UNDER BIT(1) /* underflow error */
-+#define DMA_TX_ERR_DEFER BIT(2) /* excessive deferral */
-+#define DMA_TX_COL_MASK 0x78
-+#define DMA_TX_COL_SHIFT 3
-+#define DMA_TX_ERR_HB BIT(7) /* hearbeat failure */
-+#define DMA_TX_ERR_COL BIT(8) /* excessive collisions */
-+#define DMA_TX_ERR_LATE BIT(9) /* late collision */
-+#define DMA_TX_ERR_LINK BIT(10) /* no carrier */
-+#define DMA_TX_ERR_LOSS BIT(11) /* loss of carrier */
-+#define DMA_TX_ERR_JABBER BIT(14) /* transmit jabber timeout */
-+#define DMA_TX_ERROR BIT(15) /* frame aborted */
-+#define DMA_TX_OWN BIT(31) /* descr owned by DMA controller */
-+
-+#define DMA_TX1_BSIZE_MASK 0x000007ff
-+#define DMA_TX1_BSIZE_SHIFT 0
-+#define DMA_TX1_CHAINED BIT(24) /* chained descriptors */
-+#define DMA_TX1_TER BIT(25) /* transmit end of ring */
-+#define DMA_TX1_FS BIT(29) /* first segment */
-+#define DMA_TX1_LS BIT(30) /* last segment */
-+#define DMA_TX1_IC BIT(31) /* interrupt on completion */
-+
-+#define RCVPKT_LENGTH(X) (X >> 16) /* Received pkt Length */
-+
-+#define MAC_CONTROL_RE BIT(2) /* receive enable */
-+#define MAC_CONTROL_TE BIT(3) /* transmit enable */
-+#define MAC_CONTROL_DC BIT(5) /* Deferral check */
-+#define MAC_CONTROL_ASTP BIT(8) /* Auto pad strip */
-+#define MAC_CONTROL_DRTY BIT(10) /* Disable retry */
-+#define MAC_CONTROL_DBF BIT(11) /* Disable bcast frames */
-+#define MAC_CONTROL_LCC BIT(12) /* late collision ctrl */
-+#define MAC_CONTROL_HP BIT(13) /* Hash Perfect filtering */
-+#define MAC_CONTROL_HASH BIT(14) /* Unicast hash filtering */
-+#define MAC_CONTROL_HO BIT(15) /* Hash only filtering */
-+#define MAC_CONTROL_PB BIT(16) /* Pass Bad frames */
-+#define MAC_CONTROL_IF BIT(17) /* Inverse filtering */
-+#define MAC_CONTROL_PR BIT(18) /* promis mode (valid frames only) */
-+#define MAC_CONTROL_PM BIT(19) /* pass multicast */
-+#define MAC_CONTROL_F BIT(20) /* full-duplex */
-+#define MAC_CONTROL_DRO BIT(23) /* Disable Receive Own */
-+#define MAC_CONTROL_HBD BIT(28) /* heart-beat disabled (MUST BE SET) */
-+#define MAC_CONTROL_BLE BIT(30) /* big endian mode */
-+#define MAC_CONTROL_RA BIT(31) /* rcv all (valid and invalid frames) */
-+
-+#define MII_ADDR_BUSY BIT(0)
-+#define MII_ADDR_WRITE BIT(1)
-+#define MII_ADDR_REG_SHIFT 6
-+#define MII_ADDR_PHY_SHIFT 11
-+#define MII_DATA_SHIFT 0
-+
-+#define FLOW_CONTROL_FCE BIT(1)
-+
-+#define DMA_BUS_MODE_SWR BIT(0) /* software reset */
-+#define DMA_BUS_MODE_BLE BIT(7) /* big endian mode */
-+#define DMA_BUS_MODE_PBL_SHIFT 8 /* programmable burst length 32 */
-+#define DMA_BUS_MODE_DBO BIT(20) /* big-endian descriptors */
-+
-+#define DMA_STATUS_TI BIT(0) /* transmit interrupt */
-+#define DMA_STATUS_TPS BIT(1) /* transmit process stopped */
-+#define DMA_STATUS_TU BIT(2) /* transmit buffer unavailable */
-+#define DMA_STATUS_TJT BIT(3) /* transmit buffer timeout */
-+#define DMA_STATUS_UNF BIT(5) /* transmit underflow */
-+#define DMA_STATUS_RI BIT(6) /* receive interrupt */
-+#define DMA_STATUS_RU BIT(7) /* receive buffer unavailable */
-+#define DMA_STATUS_RPS BIT(8) /* receive process stopped */
-+#define DMA_STATUS_ETI BIT(10) /* early transmit interrupt */
-+#define DMA_STATUS_FBE BIT(13) /* fatal bus interrupt */
-+#define DMA_STATUS_ERI BIT(14) /* early receive interrupt */
-+#define DMA_STATUS_AIS BIT(15) /* abnormal interrupt summary */
-+#define DMA_STATUS_NIS BIT(16) /* normal interrupt summary */
-+#define DMA_STATUS_RS_SHIFT 17 /* receive process state */
-+#define DMA_STATUS_TS_SHIFT 20 /* transmit process state */
-+#define DMA_STATUS_EB_SHIFT 23 /* error bits */
-+
-+#define DMA_CONTROL_SR BIT(1) /* start receive */
-+#define DMA_CONTROL_ST BIT(13) /* start transmit */
-+#define DMA_CONTROL_SF BIT(21) /* store and forward */
-+
-+typedef struct {
-+ volatile unsigned int status; /* OWN, Device control and status. */
-+ volatile unsigned int devcs; /* pkt Control bits + Length */
-+ volatile unsigned int addr; /* Current Address. */
-+ volatile unsigned int descr; /* Next descriptor in chain. */
-+} ar231x_descr_t;
-+
-+/**
-+ * New Combo structure for Both Eth0 AND eth1
-+ *
-+ * Don't directly access MII related regs since phy chip could be actually
-+ * connected to another ethernet block.
-+ */
-+typedef struct {
-+ volatile unsigned int mac_control; /* 0x00 */
-+ volatile unsigned int mac_addr[2]; /* 0x04 - 0x08 */
-+ volatile unsigned int mcast_table[2]; /* 0x0c - 0x10 */
-+ volatile unsigned int __mii_addr; /* 0x14 */
-+ volatile unsigned int __mii_data; /* 0x18 */
-+ volatile unsigned int flow_control; /* 0x1c */
-+ volatile unsigned int vlan_tag; /* 0x20 */
-+ volatile unsigned int pad[7]; /* 0x24 - 0x3c */
-+ volatile unsigned int ucast_table[8]; /* 0x40-0x5c */
-+} ETHERNET_STRUCT;
-+
-+typedef struct {
-+ volatile unsigned int mii_addr;
-+ volatile unsigned int mii_data;
-+} MII;
-+
-+/********************************************************************
-+ * Interrupt controller
-+ ********************************************************************/
-+
-+typedef struct {
-+ volatile unsigned int wdog_control; /* 0x08 */
-+ volatile unsigned int wdog_timer; /* 0x0c */
-+ volatile unsigned int misc_status; /* 0x10 */
-+ volatile unsigned int misc_mask; /* 0x14 */
-+ volatile unsigned int global_status; /* 0x18 */
-+ volatile unsigned int reserved; /* 0x1c */
-+ volatile unsigned int reset_control; /* 0x20 */
-+} INTERRUPT;
-+
-+/********************************************************************
-+ * DMA controller
-+ ********************************************************************/
-+typedef struct {
-+ volatile unsigned int bus_mode; /* 0x00 (CSR0) */
-+ volatile unsigned int xmt_poll; /* 0x04 (CSR1) */
-+ volatile unsigned int rcv_poll; /* 0x08 (CSR2) */
-+ volatile unsigned int rcv_base; /* 0x0c (CSR3) */
-+ volatile unsigned int xmt_base; /* 0x10 (CSR4) */
-+ volatile unsigned int status; /* 0x14 (CSR5) */
-+ volatile unsigned int control; /* 0x18 (CSR6) */
-+ volatile unsigned int intr_ena; /* 0x1c (CSR7) */
-+ volatile unsigned int rcv_missed; /* 0x20 (CSR8) */
-+ volatile unsigned int reserved[11]; /* 0x24-0x4c (CSR9-19) */
-+ volatile unsigned int cur_tx_buf_addr; /* 0x50 (CSR20) */
-+ volatile unsigned int cur_rx_buf_addr; /* 0x50 (CSR21) */
-+} DMA;
-+
-+/**
-+ * Struct private for the Sibyte.
-+ *
-+ * Elements are grouped so variables used by the tx handling goes
-+ * together, and will go into the same cache lines etc. in order to
-+ * avoid cache line contention between the rx and tx handling on SMP.
-+ *
-+ * Frequently accessed variables are put at the beginning of the
-+ * struct to help the compiler generate better/shorter code.
-+ */
-+struct ar231x_private {
-+ struct net_device *dev;
-+ int version;
-+ u32 mb[2];
-+
-+ volatile MII *phy_regs;
-+ volatile ETHERNET_STRUCT *eth_regs;
-+ volatile DMA *dma_regs;
-+ struct ar231x_eth *cfg;
-+
-+ spinlock_t lock; /* Serialise access to device */
-+
-+ /* RX and TX descriptors, must be adjacent */
-+ ar231x_descr_t *rx_ring;
-+ ar231x_descr_t *tx_ring;
-+
-+ struct sk_buff **rx_skb;
-+ struct sk_buff **tx_skb;
-+
-+ /* RX elements */
-+ u32 rx_skbprd;
-+ u32 cur_rx;
-+
-+ /* TX elements */
-+ u32 tx_prd;
-+ u32 tx_csm;
-+
-+ /* Misc elements */
-+ char name[48];
-+ struct {
-+ u32 address;
-+ u32 length;
-+ char *mapping;
-+ } desc;
-+
-+ struct timer_list link_timer;
-+ unsigned short phy; /* merlot phy = 1, samsung phy = 0x1f */
-+ unsigned short mac;
-+ unsigned short link; /* 0 - link down, 1 - link up */
-+ u16 phy_data;
-+
-+ struct tasklet_struct rx_tasklet;
-+ int unloading;
-+
-+ struct phy_device *phy_dev;
-+ struct mii_bus *mii_bus;
-+ int oldduplex;
-+};
-+
-+/* Prototypes */
-+static int ar231x_init(struct net_device *dev);
-+#ifdef TX_TIMEOUT
-+static void ar231x_tx_timeout(struct net_device *dev);
-+#endif
-+static int ar231x_restart(struct net_device *dev);
-+static void ar231x_load_rx_ring(struct net_device *dev, int bufs);
-+static irqreturn_t ar231x_interrupt(int irq, void *dev_id);
-+static int ar231x_open(struct net_device *dev);
-+static int ar231x_start_xmit(struct sk_buff *skb, struct net_device *dev);
-+static int ar231x_close(struct net_device *dev);
-+static int ar231x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd);
-+static void ar231x_init_cleanup(struct net_device *dev);
-+static int ar231x_setup_timer(struct net_device *dev);
-+static void ar231x_link_timer_fn(unsigned long data);
-+static void ar231x_check_link(struct net_device *dev);
-+
-+#endif /* _AR2313_H_ */
---- a/arch/mips/ath25/ar2315_regs.h
-+++ b/arch/mips/ath25/ar2315_regs.h
-@@ -57,6 +57,9 @@
- #define AR2315_PCI_EXT_BASE 0x80000000 /* PCI external */
- #define AR2315_PCI_EXT_SIZE 0x40000000
-
-+/* MII registers offset inside Ethernet MMR region */
-+#define AR2315_ENET0_MII_BASE (AR2315_ENET0_BASE + 0x14)
-+
- /*
- * Configuration registers
- */
---- a/arch/mips/ath25/ar5312_regs.h
-+++ b/arch/mips/ath25/ar5312_regs.h
-@@ -64,6 +64,10 @@
- #define AR5312_AR5312_REV7 0x0057 /* AR5312 WMAC (AP30-040) */
- #define AR5312_AR2313_REV8 0x0058 /* AR2313 WMAC (AP43-030) */
-
-+/* MII registers offset inside Ethernet MMR region */
-+#define AR5312_ENET0_MII_BASE (AR5312_ENET0_BASE + 0x14)
-+#define AR5312_ENET1_MII_BASE (AR5312_ENET1_BASE + 0x14)
-+
- /* Reset/Timer Block Address Map */
- #define AR5312_TIMER 0x0000 /* countdown timer */
- #define AR5312_RELOAD 0x0004 /* timer reload value */
---- a/arch/mips/ath25/ar2315.c
-+++ b/arch/mips/ath25/ar2315.c
-@@ -136,6 +136,8 @@ static void ar2315_irq_dispatch(void)
-
- if (pending & CAUSEF_IP3)
- do_IRQ(AR2315_IRQ_WLAN0);
-+ else if (pending & CAUSEF_IP4)
-+ do_IRQ(AR2315_IRQ_ENET0);
- #ifdef CONFIG_PCI_AR2315
- else if (pending & CAUSEF_IP5)
- do_IRQ(AR2315_IRQ_LCBUS_PCI);
-@@ -169,6 +171,29 @@ void __init ar2315_arch_init_irq(void)
- ar2315_misc_irq_domain = domain;
- }
-
-+static void ar2315_device_reset_set(u32 mask)
-+{
-+ u32 val;
-+
-+ val = ar2315_rst_reg_read(AR2315_RESET);
-+ ar2315_rst_reg_write(AR2315_RESET, val | mask);
-+}
-+
-+static void ar2315_device_reset_clear(u32 mask)
-+{
-+ u32 val;
-+
-+ val = ar2315_rst_reg_read(AR2315_RESET);
-+ ar2315_rst_reg_write(AR2315_RESET, val & ~mask);
-+}
-+
-+static struct ar231x_eth ar2315_eth_data = {
-+ .reset_set = ar2315_device_reset_set,
-+ .reset_clear = ar2315_device_reset_clear,
-+ .reset_mac = AR2315_RESET_ENET0,
-+ .reset_phy = AR2315_RESET_EPHY0,
-+};
-+
- static struct resource ar2315_gpio_res[] = {
- {
- .name = "ar2315-gpio",
-@@ -205,6 +230,11 @@ void __init ar2315_init_devices(void)
- ar2315_gpio_res[1].end = ar2315_gpio_res[1].start;
- platform_device_register(&ar2315_gpio);
-
-+ ar2315_eth_data.macaddr = ath25_board.config->enet0_mac;
-+ ath25_add_ethernet(0, AR2315_ENET0_BASE, "eth0_mii",
-+ AR2315_ENET0_MII_BASE, AR2315_IRQ_ENET0,
-+ &ar2315_eth_data);
-+
- ath25_add_wmac(0, AR2315_WLAN0_BASE, AR2315_IRQ_WLAN0);
- }
-
---- a/arch/mips/ath25/ar5312.c
-+++ b/arch/mips/ath25/ar5312.c
-@@ -132,6 +132,10 @@ static void ar5312_irq_dispatch(void)
-
- if (pending & CAUSEF_IP2)
- do_IRQ(AR5312_IRQ_WLAN0);
-+ else if (pending & CAUSEF_IP3)
-+ do_IRQ(AR5312_IRQ_ENET0);
-+ else if (pending & CAUSEF_IP4)
-+ do_IRQ(AR5312_IRQ_ENET1);
- else if (pending & CAUSEF_IP5)
- do_IRQ(AR5312_IRQ_WLAN1);
- else if (pending & CAUSEF_IP6)
-@@ -163,6 +167,36 @@ void __init ar5312_arch_init_irq(void)
- ar5312_misc_irq_domain = domain;
- }
-
-+static void ar5312_device_reset_set(u32 mask)
-+{
-+ u32 val;
-+
-+ val = ar5312_rst_reg_read(AR5312_RESET);
-+ ar5312_rst_reg_write(AR5312_RESET, val | mask);
-+}
-+
-+static void ar5312_device_reset_clear(u32 mask)
-+{
-+ u32 val;
-+
-+ val = ar5312_rst_reg_read(AR5312_RESET);
-+ ar5312_rst_reg_write(AR5312_RESET, val & ~mask);
-+}
-+
-+static struct ar231x_eth ar5312_eth0_data = {
-+ .reset_set = ar5312_device_reset_set,
-+ .reset_clear = ar5312_device_reset_clear,
-+ .reset_mac = AR5312_RESET_ENET0,
-+ .reset_phy = AR5312_RESET_EPHY0,
-+};
-+
-+static struct ar231x_eth ar5312_eth1_data = {
-+ .reset_set = ar5312_device_reset_set,
-+ .reset_clear = ar5312_device_reset_clear,
-+ .reset_mac = AR5312_RESET_ENET1,
-+ .reset_phy = AR5312_RESET_EPHY1,
-+};
-+
- static struct physmap_flash_data ar5312_flash_data = {
- .width = 2,
- };
-@@ -243,6 +277,7 @@ static void __init ar5312_flash_init(voi
- void __init ar5312_init_devices(void)
- {
- struct ath25_boarddata *config;
-+ u8 *c;
-
- ar5312_flash_init();
-
-@@ -266,8 +301,30 @@ void __init ar5312_init_devices(void)
-
- platform_device_register(&ar5312_gpio);
-
-+ /* Fix up MAC addresses if necessary */
-+ if (is_broadcast_ether_addr(config->enet0_mac))
-+ ether_addr_copy(config->enet0_mac, config->enet1_mac);
-+
-+ /* If ENET0 and ENET1 have the same mac address,
-+ * increment the one from ENET1 */
-+ if (ether_addr_equal(config->enet0_mac, config->enet1_mac)) {
-+ c = config->enet1_mac + 5;
-+ while ((c >= config->enet1_mac) && !(++(*c)))
-+ c--;
-+ }
-+
- switch (ath25_soc) {
- case ATH25_SOC_AR5312:
-+ ar5312_eth0_data.macaddr = config->enet0_mac;
-+ ath25_add_ethernet(0, AR5312_ENET0_BASE, "eth0_mii",
-+ AR5312_ENET0_MII_BASE, AR5312_IRQ_ENET0,
-+ &ar5312_eth0_data);
-+
-+ ar5312_eth1_data.macaddr = config->enet1_mac;
-+ ath25_add_ethernet(1, AR5312_ENET1_BASE, "eth1_mii",
-+ AR5312_ENET1_MII_BASE, AR5312_IRQ_ENET1,
-+ &ar5312_eth1_data);
-+
- if (!ath25_board.radio)
- return;
-
-@@ -276,8 +333,18 @@ void __init ar5312_init_devices(void)
-
- ath25_add_wmac(0, AR5312_WLAN0_BASE, AR5312_IRQ_WLAN0);
- break;
-+ /*
-+ * AR2312/3 ethernet uses the PHY of ENET0, but the MAC
-+ * of ENET1. Atheros calls it 'twisted' for a reason :)
-+ */
- case ATH25_SOC_AR2312:
- case ATH25_SOC_AR2313:
-+ ar5312_eth1_data.reset_phy = ar5312_eth0_data.reset_phy;
-+ ar5312_eth1_data.macaddr = config->enet0_mac;
-+ ath25_add_ethernet(1, AR5312_ENET1_BASE, "eth0_mii",
-+ AR5312_ENET0_MII_BASE, AR5312_IRQ_ENET1,
-+ &ar5312_eth1_data);
-+
- if (!ath25_board.radio)
- return;
- break;
---- a/arch/mips/ath25/devices.h
-+++ b/arch/mips/ath25/devices.h
-@@ -32,6 +32,8 @@ extern struct ar231x_board_config ath25_
- extern void (*ath25_irq_dispatch)(void);
-
- int ath25_find_config(phys_addr_t offset, unsigned long size);
-+int ath25_add_ethernet(int nr, u32 base, const char *mii_name, u32 mii_base,
-+ int irq, void *pdata);
- void ath25_serial_setup(u32 mapbase, int irq, unsigned int uartclk);
- int ath25_add_wmac(int nr, u32 base, int irq);
-
---- a/arch/mips/ath25/devices.c
-+++ b/arch/mips/ath25/devices.c
-@@ -12,6 +12,51 @@
- struct ar231x_board_config ath25_board;
- enum ath25_soc_type ath25_soc = ATH25_SOC_UNKNOWN;
-
-+static struct resource ath25_eth0_res[] = {
-+ {
-+ .name = "eth0_membase",
-+ .flags = IORESOURCE_MEM,
-+ },
-+ {
-+ .name = "eth0_mii",
-+ .flags = IORESOURCE_MEM,
-+ },
-+ {
-+ .name = "eth0_irq",
-+ .flags = IORESOURCE_IRQ,
-+ }
-+};
-+
-+static struct resource ath25_eth1_res[] = {
-+ {
-+ .name = "eth1_membase",
-+ .flags = IORESOURCE_MEM,
-+ },
-+ {
-+ .name = "eth1_mii",
-+ .flags = IORESOURCE_MEM,
-+ },
-+ {
-+ .name = "eth1_irq",
-+ .flags = IORESOURCE_IRQ,
-+ }
-+};
-+
-+static struct platform_device ath25_eth[] = {
-+ {
-+ .id = 0,
-+ .name = "ar231x-eth",
-+ .resource = ath25_eth0_res,
-+ .num_resources = ARRAY_SIZE(ath25_eth0_res)
-+ },
-+ {
-+ .id = 1,
-+ .name = "ar231x-eth",
-+ .resource = ath25_eth1_res,
-+ .num_resources = ARRAY_SIZE(ath25_eth1_res)
-+ }
-+};
-+
- static struct resource ath25_wmac0_res[] = {
- {
- .name = "wmac0_membase",
-@@ -70,6 +115,25 @@ const char *get_system_type(void)
- return soc_type_strings[ath25_soc];
- }
-
-+int __init ath25_add_ethernet(int nr, u32 base, const char *mii_name,
-+ u32 mii_base, int irq, void *pdata)
-+{
-+ struct resource *res;
-+
-+ ath25_eth[nr].dev.platform_data = pdata;
-+ res = &ath25_eth[nr].resource[0];
-+ res->start = base;
-+ res->end = base + 0x2000 - 1;
-+ res++;
-+ res->name = mii_name;
-+ res->start = mii_base;
-+ res->end = mii_base + 8 - 1;
-+ res++;
-+ res->start = irq;
-+ res->end = irq;
-+ return platform_device_register(&ath25_eth[nr]);
-+}
-+
- void __init ath25_serial_setup(u32 mapbase, int irq, unsigned int uartclk)
- {
- struct uart_port s;
---- a/arch/mips/include/asm/mach-ath25/ath25_platform.h
-+++ b/arch/mips/include/asm/mach-ath25/ath25_platform.h
-@@ -70,4 +70,15 @@ struct ar231x_board_config {
- const char *radio;
- };
-
-+/*
-+ * Platform device information for the Ethernet MAC
-+ */
-+struct ar231x_eth {
-+ void (*reset_set)(u32);
-+ void (*reset_clear)(u32);
-+ u32 reset_mac;
-+ u32 reset_phy;
-+ char *macaddr;
-+};
-+
- #endif /* __ASM_MACH_ATH25_PLATFORM_H */
+++ /dev/null
---- a/drivers/mtd/devices/Kconfig
-+++ b/drivers/mtd/devices/Kconfig
-@@ -120,6 +120,10 @@ config MTD_BCM47XXSFLASH
- registered by bcma as platform devices. This enables driver for
- serial flash memories (only read-only mode is implemented).
-
-+config MTD_AR2315
-+ tristate "Atheros AR2315+ SPI Flash support"
-+ depends on SOC_AR2315
-+
- config MTD_SLRAM
- tristate "Uncached system RAM"
- help
---- a/drivers/mtd/devices/Makefile
-+++ b/drivers/mtd/devices/Makefile
-@@ -14,6 +14,7 @@ obj-$(CONFIG_MTD_DATAFLASH) += mtd_dataf
- obj-$(CONFIG_MTD_M25P80) += m25p80.o
- obj-$(CONFIG_MTD_SPEAR_SMI) += spear_smi.o
- obj-$(CONFIG_MTD_SST25L) += sst25l.o
-+obj-$(CONFIG_MTD_AR2315) += ar2315.o
- obj-$(CONFIG_MTD_BCM47XXSFLASH) += bcm47xxsflash.o
- obj-$(CONFIG_MTD_ST_SPI_FSM) += st_spi_fsm.o
- obj-$(CONFIG_MTD_POWERNV_FLASH) += powernv_flash.o
---- /dev/null
-+++ b/drivers/mtd/devices/ar2315.c
-@@ -0,0 +1,459 @@
-+
-+/*
-+ * MTD driver for the SPI Flash Memory support on Atheros AR2315
-+ *
-+ * Copyright (c) 2005-2006 Atheros Communications Inc.
-+ * Copyright (C) 2006-2007 FON Technology, SL.
-+ * Copyright (C) 2006-2007 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006-2009 Felix Fietkau <nbd@nbd.name>
-+ * Copyright (C) 2012 Alexandros C. Couloumbis <alex@ozo.com>
-+ *
-+ * This code is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ *
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/module.h>
-+#include <linux/types.h>
-+#include <linux/errno.h>
-+#include <linux/slab.h>
-+#include <linux/mtd/mtd.h>
-+#include <linux/mtd/partitions.h>
-+#include <linux/platform_device.h>
-+#include <linux/sched.h>
-+#include <linux/delay.h>
-+#include <linux/io.h>
-+#include <linux/mutex.h>
-+
-+#include "ar2315_spiflash.h"
-+
-+#define DRIVER_NAME "ar2315-spiflash"
-+
-+#define busy_wait(_priv, _condition, _wait) do { \
-+ while (_condition) { \
-+ if (_wait > 1) \
-+ msleep(_wait); \
-+ else if ((_wait == 1) && need_resched()) \
-+ schedule(); \
-+ else \
-+ udelay(1); \
-+ } \
-+} while (0)
-+
-+enum {
-+ FLASH_NONE,
-+ FLASH_1MB,
-+ FLASH_2MB,
-+ FLASH_4MB,
-+ FLASH_8MB,
-+ FLASH_16MB,
-+};
-+
-+/* Flash configuration table */
-+struct flashconfig {
-+ u32 byte_cnt;
-+ u32 sector_cnt;
-+ u32 sector_size;
-+};
-+
-+static const struct flashconfig flashconfig_tbl[] = {
-+ [FLASH_NONE] = { 0, 0, 0},
-+ [FLASH_1MB] = { STM_1MB_BYTE_COUNT, STM_1MB_SECTOR_COUNT,
-+ STM_1MB_SECTOR_SIZE},
-+ [FLASH_2MB] = { STM_2MB_BYTE_COUNT, STM_2MB_SECTOR_COUNT,
-+ STM_2MB_SECTOR_SIZE},
-+ [FLASH_4MB] = { STM_4MB_BYTE_COUNT, STM_4MB_SECTOR_COUNT,
-+ STM_4MB_SECTOR_SIZE},
-+ [FLASH_8MB] = { STM_8MB_BYTE_COUNT, STM_8MB_SECTOR_COUNT,
-+ STM_8MB_SECTOR_SIZE},
-+ [FLASH_16MB] = { STM_16MB_BYTE_COUNT, STM_16MB_SECTOR_COUNT,
-+ STM_16MB_SECTOR_SIZE}
-+};
-+
-+/* Mapping of generic opcodes to STM serial flash opcodes */
-+enum {
-+ SPI_WRITE_ENABLE,
-+ SPI_WRITE_DISABLE,
-+ SPI_RD_STATUS,
-+ SPI_WR_STATUS,
-+ SPI_RD_DATA,
-+ SPI_FAST_RD_DATA,
-+ SPI_PAGE_PROGRAM,
-+ SPI_SECTOR_ERASE,
-+ SPI_BULK_ERASE,
-+ SPI_DEEP_PWRDOWN,
-+ SPI_RD_SIG,
-+};
-+
-+struct opcodes {
-+ __u16 code;
-+ __s8 tx_cnt;
-+ __s8 rx_cnt;
-+};
-+
-+static const struct opcodes stm_opcodes[] = {
-+ [SPI_WRITE_ENABLE] = {STM_OP_WR_ENABLE, 1, 0},
-+ [SPI_WRITE_DISABLE] = {STM_OP_WR_DISABLE, 1, 0},
-+ [SPI_RD_STATUS] = {STM_OP_RD_STATUS, 1, 1},
-+ [SPI_WR_STATUS] = {STM_OP_WR_STATUS, 1, 0},
-+ [SPI_RD_DATA] = {STM_OP_RD_DATA, 4, 4},
-+ [SPI_FAST_RD_DATA] = {STM_OP_FAST_RD_DATA, 5, 0},
-+ [SPI_PAGE_PROGRAM] = {STM_OP_PAGE_PGRM, 8, 0},
-+ [SPI_SECTOR_ERASE] = {STM_OP_SECTOR_ERASE, 4, 0},
-+ [SPI_BULK_ERASE] = {STM_OP_BULK_ERASE, 1, 0},
-+ [SPI_DEEP_PWRDOWN] = {STM_OP_DEEP_PWRDOWN, 1, 0},
-+ [SPI_RD_SIG] = {STM_OP_RD_SIG, 4, 1},
-+};
-+
-+/* Driver private data structure */
-+struct spiflash_priv {
-+ struct mtd_info mtd;
-+ void __iomem *readaddr; /* memory mapped data for read */
-+ void __iomem *mmraddr; /* memory mapped register space */
-+ struct mutex lock; /* serialize registers access */
-+};
-+
-+#define to_spiflash(_mtd) container_of(_mtd, struct spiflash_priv, mtd)
-+
-+enum {
-+ FL_READY,
-+ FL_READING,
-+ FL_ERASING,
-+ FL_WRITING
-+};
-+
-+/*****************************************************************************/
-+
-+static u32
-+spiflash_read_reg(struct spiflash_priv *priv, int reg)
-+{
-+ return ioread32(priv->mmraddr + reg);
-+}
-+
-+static void
-+spiflash_write_reg(struct spiflash_priv *priv, int reg, u32 data)
-+{
-+ iowrite32(data, priv->mmraddr + reg);
-+}
-+
-+static u32
-+spiflash_wait_busy(struct spiflash_priv *priv)
-+{
-+ u32 reg;
-+
-+ busy_wait(priv, (reg = spiflash_read_reg(priv, SPI_FLASH_CTL)) &
-+ SPI_CTL_BUSY, 0);
-+ return reg;
-+}
-+
-+static u32
-+spiflash_sendcmd(struct spiflash_priv *priv, int opcode, u32 addr)
-+{
-+ const struct opcodes *op;
-+ u32 reg, mask;
-+
-+ op = &stm_opcodes[opcode];
-+ reg = spiflash_wait_busy(priv);
-+ spiflash_write_reg(priv, SPI_FLASH_OPCODE,
-+ ((u32)op->code) | (addr << 8));
-+
-+ reg &= ~SPI_CTL_TX_RX_CNT_MASK;
-+ reg |= SPI_CTL_START | op->tx_cnt | (op->rx_cnt << 4);
-+
-+ spiflash_write_reg(priv, SPI_FLASH_CTL, reg);
-+ spiflash_wait_busy(priv);
-+
-+ if (!op->rx_cnt)
-+ return 0;
-+
-+ reg = spiflash_read_reg(priv, SPI_FLASH_DATA);
-+
-+ switch (op->rx_cnt) {
-+ case 1:
-+ mask = 0x000000ff;
-+ break;
-+ case 2:
-+ mask = 0x0000ffff;
-+ break;
-+ case 3:
-+ mask = 0x00ffffff;
-+ break;
-+ default:
-+ mask = 0xffffffff;
-+ break;
-+ }
-+ reg &= mask;
-+
-+ return reg;
-+}
-+
-+/*
-+ * Probe SPI flash device
-+ * Function returns 0 for failure.
-+ * and flashconfig_tbl array index for success.
-+ */
-+static int
-+spiflash_probe_chip(struct platform_device *pdev, struct spiflash_priv *priv)
-+{
-+ u32 sig = spiflash_sendcmd(priv, SPI_RD_SIG, 0);
-+ int flash_size;
-+
-+ switch (sig) {
-+ case STM_8MBIT_SIGNATURE:
-+ flash_size = FLASH_1MB;
-+ break;
-+ case STM_16MBIT_SIGNATURE:
-+ flash_size = FLASH_2MB;
-+ break;
-+ case STM_32MBIT_SIGNATURE:
-+ flash_size = FLASH_4MB;
-+ break;
-+ case STM_64MBIT_SIGNATURE:
-+ flash_size = FLASH_8MB;
-+ break;
-+ case STM_128MBIT_SIGNATURE:
-+ flash_size = FLASH_16MB;
-+ break;
-+ default:
-+ dev_warn(&pdev->dev, "read of flash device signature failed!\n");
-+ return 0;
-+ }
-+
-+ return flash_size;
-+}
-+
-+static void
-+spiflash_wait_complete(struct spiflash_priv *priv, unsigned int timeout)
-+{
-+ busy_wait(priv, spiflash_sendcmd(priv, SPI_RD_STATUS, 0) &
-+ SPI_STATUS_WIP, timeout);
-+}
-+
-+static int
-+spiflash_erase(struct mtd_info *mtd, struct erase_info *instr)
-+{
-+ struct spiflash_priv *priv = to_spiflash(mtd);
-+ const struct opcodes *op;
-+ u32 temp, reg;
-+
-+ if (instr->addr + instr->len > mtd->size)
-+ return -EINVAL;
-+
-+ mutex_lock(&priv->lock);
-+
-+ spiflash_sendcmd(priv, SPI_WRITE_ENABLE, 0);
-+ reg = spiflash_wait_busy(priv);
-+
-+ op = &stm_opcodes[SPI_SECTOR_ERASE];
-+ temp = ((u32)instr->addr << 8) | (u32)(op->code);
-+ spiflash_write_reg(priv, SPI_FLASH_OPCODE, temp);
-+
-+ reg &= ~SPI_CTL_TX_RX_CNT_MASK;
-+ reg |= op->tx_cnt | SPI_CTL_START;
-+ spiflash_write_reg(priv, SPI_FLASH_CTL, reg);
-+
-+ spiflash_wait_complete(priv, 20);
-+
-+ mutex_unlock(&priv->lock);
-+
-+ instr->state = MTD_ERASE_DONE;
-+ mtd_erase_callback(instr);
-+
-+ return 0;
-+}
-+
-+static int
-+spiflash_read(struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen,
-+ u_char *buf)
-+{
-+ struct spiflash_priv *priv = to_spiflash(mtd);
-+
-+ if (!len)
-+ return 0;
-+
-+ if (from + len > mtd->size)
-+ return -EINVAL;
-+
-+ *retlen = len;
-+
-+ mutex_lock(&priv->lock);
-+
-+ memcpy_fromio(buf, priv->readaddr + from, len);
-+
-+ mutex_unlock(&priv->lock);
-+
-+ return 0;
-+}
-+
-+static int
-+spiflash_write(struct mtd_info *mtd, loff_t to, size_t len, size_t *retlen,
-+ const u8 *buf)
-+{
-+ struct spiflash_priv *priv = to_spiflash(mtd);
-+ u32 opcode, bytes_left;
-+
-+ *retlen = 0;
-+
-+ if (!len)
-+ return 0;
-+
-+ if (to + len > mtd->size)
-+ return -EINVAL;
-+
-+ bytes_left = len;
-+
-+ do {
-+ u32 read_len, reg, page_offset, spi_data = 0;
-+
-+ read_len = min(bytes_left, sizeof(u32));
-+
-+ /* 32-bit writes cannot span across a page boundary
-+ * (256 bytes). This types of writes require two page
-+ * program operations to handle it correctly. The STM part
-+ * will write the overflow data to the beginning of the
-+ * current page as opposed to the subsequent page.
-+ */
-+ page_offset = (to & (STM_PAGE_SIZE - 1)) + read_len;
-+
-+ if (page_offset > STM_PAGE_SIZE)
-+ read_len -= (page_offset - STM_PAGE_SIZE);
-+
-+ mutex_lock(&priv->lock);
-+
-+ spiflash_sendcmd(priv, SPI_WRITE_ENABLE, 0);
-+ spi_data = 0;
-+ switch (read_len) {
-+ case 4:
-+ spi_data |= buf[3] << 24;
-+ /* fall through */
-+ case 3:
-+ spi_data |= buf[2] << 16;
-+ /* fall through */
-+ case 2:
-+ spi_data |= buf[1] << 8;
-+ /* fall through */
-+ case 1:
-+ spi_data |= buf[0] & 0xff;
-+ break;
-+ default:
-+ break;
-+ }
-+
-+ spiflash_write_reg(priv, SPI_FLASH_DATA, spi_data);
-+ opcode = stm_opcodes[SPI_PAGE_PROGRAM].code |
-+ (to & 0x00ffffff) << 8;
-+ spiflash_write_reg(priv, SPI_FLASH_OPCODE, opcode);
-+
-+ reg = spiflash_read_reg(priv, SPI_FLASH_CTL);
-+ reg &= ~SPI_CTL_TX_RX_CNT_MASK;
-+ reg |= (read_len + 4) | SPI_CTL_START;
-+ spiflash_write_reg(priv, SPI_FLASH_CTL, reg);
-+
-+ spiflash_wait_complete(priv, 1);
-+
-+ mutex_unlock(&priv->lock);
-+
-+ bytes_left -= read_len;
-+ to += read_len;
-+ buf += read_len;
-+
-+ *retlen += read_len;
-+ } while (bytes_left != 0);
-+
-+ return 0;
-+}
-+
-+#if defined CONFIG_MTD_REDBOOT_PARTS || CONFIG_MTD_MYLOADER_PARTS
-+static const char * const part_probe_types[] = {
-+ "cmdlinepart", "RedBoot", "MyLoader", NULL
-+};
-+#endif
-+
-+static int
-+spiflash_probe(struct platform_device *pdev)
-+{
-+ struct spiflash_priv *priv;
-+ struct mtd_info *mtd;
-+ struct resource *res;
-+ int index;
-+ int result = 0;
-+
-+ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
-+ if (!priv)
-+ return -ENOMEM;
-+
-+ mutex_init(&priv->lock);
-+ mtd = &priv->mtd;
-+
-+ res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-+ priv->mmraddr = devm_ioremap_resource(&pdev->dev, res);
-+ if (IS_ERR(priv->mmraddr)) {
-+ dev_warn(&pdev->dev, "failed to map flash MMR\n");
-+ return PTR_ERR(priv->mmraddr);
-+ }
-+
-+ index = spiflash_probe_chip(pdev, priv);
-+ if (!index) {
-+ dev_warn(&pdev->dev, "found no flash device\n");
-+ return -ENODEV;
-+ }
-+
-+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ priv->readaddr = devm_ioremap_resource(&pdev->dev, res);
-+ if (IS_ERR(priv->readaddr)) {
-+ dev_warn(&pdev->dev, "failed to map flash read mem\n");
-+ return PTR_ERR(priv->readaddr);
-+ }
-+
-+ platform_set_drvdata(pdev, priv);
-+ mtd->name = "spiflash";
-+ mtd->type = MTD_NORFLASH;
-+ mtd->flags = (MTD_CAP_NORFLASH|MTD_WRITEABLE);
-+ mtd->size = flashconfig_tbl[index].byte_cnt;
-+ mtd->erasesize = flashconfig_tbl[index].sector_size;
-+ mtd->writesize = 1;
-+ mtd->numeraseregions = 0;
-+ mtd->eraseregions = NULL;
-+ mtd->_erase = spiflash_erase;
-+ mtd->_read = spiflash_read;
-+ mtd->_write = spiflash_write;
-+ mtd->owner = THIS_MODULE;
-+
-+ dev_info(&pdev->dev, "%lld Kbytes flash detected\n", mtd->size >> 10);
-+
-+#if defined CONFIG_MTD_REDBOOT_PARTS || CONFIG_MTD_MYLOADER_PARTS
-+ /* parse redboot partitions */
-+
-+ result = mtd_device_parse_register(mtd, part_probe_types,
-+ NULL, NULL, 0);
-+#endif
-+
-+ return result;
-+}
-+
-+static int
-+spiflash_remove(struct platform_device *pdev)
-+{
-+ struct spiflash_priv *priv = platform_get_drvdata(pdev);
-+
-+ mtd_device_unregister(&priv->mtd);
-+
-+ return 0;
-+}
-+
-+static struct platform_driver spiflash_driver = {
-+ .driver.name = DRIVER_NAME,
-+ .probe = spiflash_probe,
-+ .remove = spiflash_remove,
-+};
-+
-+module_platform_driver(spiflash_driver);
-+
-+MODULE_LICENSE("GPL");
-+MODULE_AUTHOR("OpenWrt.org");
-+MODULE_AUTHOR("Atheros Communications Inc");
-+MODULE_DESCRIPTION("MTD driver for SPI Flash on Atheros AR2315+ SOC");
-+MODULE_ALIAS("platform:" DRIVER_NAME);
-+
---- /dev/null
-+++ b/drivers/mtd/devices/ar2315_spiflash.h
-@@ -0,0 +1,106 @@
-+/*
-+ * Atheros AR2315 SPI Flash Memory support header file.
-+ *
-+ * Copyright (c) 2005, Atheros Communications Inc.
-+ * Copyright (C) 2006 FON Technology, SL.
-+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
-+ * Copyright (C) 2006-2009 Felix Fietkau <nbd@nbd.name>
-+ *
-+ * This code is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License version 2 as
-+ * published by the Free Software Foundation.
-+ *
-+ */
-+#ifndef __AR2315_SPIFLASH_H
-+#define __AR2315_SPIFLASH_H
-+
-+#define STM_PAGE_SIZE 256
-+
-+#define SFI_WRITE_BUFFER_SIZE 4
-+#define SFI_FLASH_ADDR_MASK 0x00ffffff
-+
-+#define STM_8MBIT_SIGNATURE 0x13
-+#define STM_M25P80_BYTE_COUNT 1048576
-+#define STM_M25P80_SECTOR_COUNT 16
-+#define STM_M25P80_SECTOR_SIZE 0x10000
-+
-+#define STM_16MBIT_SIGNATURE 0x14
-+#define STM_M25P16_BYTE_COUNT 2097152
-+#define STM_M25P16_SECTOR_COUNT 32
-+#define STM_M25P16_SECTOR_SIZE 0x10000
-+
-+#define STM_32MBIT_SIGNATURE 0x15
-+#define STM_M25P32_BYTE_COUNT 4194304
-+#define STM_M25P32_SECTOR_COUNT 64
-+#define STM_M25P32_SECTOR_SIZE 0x10000
-+
-+#define STM_64MBIT_SIGNATURE 0x16
-+#define STM_M25P64_BYTE_COUNT 8388608
-+#define STM_M25P64_SECTOR_COUNT 128
-+#define STM_M25P64_SECTOR_SIZE 0x10000
-+
-+#define STM_128MBIT_SIGNATURE 0x17
-+#define STM_M25P128_BYTE_COUNT 16777216
-+#define STM_M25P128_SECTOR_COUNT 256
-+#define STM_M25P128_SECTOR_SIZE 0x10000
-+
-+#define STM_1MB_BYTE_COUNT STM_M25P80_BYTE_COUNT
-+#define STM_1MB_SECTOR_COUNT STM_M25P80_SECTOR_COUNT
-+#define STM_1MB_SECTOR_SIZE STM_M25P80_SECTOR_SIZE
-+#define STM_2MB_BYTE_COUNT STM_M25P16_BYTE_COUNT
-+#define STM_2MB_SECTOR_COUNT STM_M25P16_SECTOR_COUNT
-+#define STM_2MB_SECTOR_SIZE STM_M25P16_SECTOR_SIZE
-+#define STM_4MB_BYTE_COUNT STM_M25P32_BYTE_COUNT
-+#define STM_4MB_SECTOR_COUNT STM_M25P32_SECTOR_COUNT
-+#define STM_4MB_SECTOR_SIZE STM_M25P32_SECTOR_SIZE
-+#define STM_8MB_BYTE_COUNT STM_M25P64_BYTE_COUNT
-+#define STM_8MB_SECTOR_COUNT STM_M25P64_SECTOR_COUNT
-+#define STM_8MB_SECTOR_SIZE STM_M25P64_SECTOR_SIZE
-+#define STM_16MB_BYTE_COUNT STM_M25P128_BYTE_COUNT
-+#define STM_16MB_SECTOR_COUNT STM_M25P128_SECTOR_COUNT
-+#define STM_16MB_SECTOR_SIZE STM_M25P128_SECTOR_SIZE
-+
-+/*
-+ * ST Microelectronics Opcodes for Serial Flash
-+ */
-+
-+#define STM_OP_WR_ENABLE 0x06 /* Write Enable */
-+#define STM_OP_WR_DISABLE 0x04 /* Write Disable */
-+#define STM_OP_RD_STATUS 0x05 /* Read Status */
-+#define STM_OP_WR_STATUS 0x01 /* Write Status */
-+#define STM_OP_RD_DATA 0x03 /* Read Data */
-+#define STM_OP_FAST_RD_DATA 0x0b /* Fast Read Data */
-+#define STM_OP_PAGE_PGRM 0x02 /* Page Program */
-+#define STM_OP_SECTOR_ERASE 0xd8 /* Sector Erase */
-+#define STM_OP_BULK_ERASE 0xc7 /* Bulk Erase */
-+#define STM_OP_DEEP_PWRDOWN 0xb9 /* Deep Power-Down Mode */
-+#define STM_OP_RD_SIG 0xab /* Read Electronic Signature */
-+
-+#define STM_STATUS_WIP 0x01 /* Write-In-Progress */
-+#define STM_STATUS_WEL 0x02 /* Write Enable Latch */
-+#define STM_STATUS_BP0 0x04 /* Block Protect 0 */
-+#define STM_STATUS_BP1 0x08 /* Block Protect 1 */
-+#define STM_STATUS_BP2 0x10 /* Block Protect 2 */
-+#define STM_STATUS_SRWD 0x80 /* Status Register Write Disable */
-+
-+/*
-+ * SPI Flash Interface Registers
-+ */
-+
-+#define SPI_FLASH_CTL 0x00
-+#define SPI_FLASH_OPCODE 0x04
-+#define SPI_FLASH_DATA 0x08
-+
-+#define SPI_CTL_START 0x00000100
-+#define SPI_CTL_BUSY 0x00010000
-+#define SPI_CTL_TXCNT_MASK 0x0000000f
-+#define SPI_CTL_RXCNT_MASK 0x000000f0
-+#define SPI_CTL_TX_RX_CNT_MASK 0x000000ff
-+#define SPI_CTL_SIZE_MASK 0x00060000
-+
-+#define SPI_CTL_CLK_SEL_MASK 0x03000000
-+#define SPI_OPCODE_MASK 0x000000ff
-+
-+#define SPI_STATUS_WIP STM_STATUS_WIP
-+
-+#endif
---- a/arch/mips/ath25/ar2315.c
-+++ b/arch/mips/ath25/ar2315.c
-@@ -220,6 +220,28 @@ static struct platform_device ar2315_gpi
- .num_resources = ARRAY_SIZE(ar2315_gpio_res)
- };
-
-+static struct resource ar2315_spiflash_res[] = {
-+ {
-+ .name = "spiflash_read",
-+ .flags = IORESOURCE_MEM,
-+ .start = AR2315_SPI_READ_BASE,
-+ .end = AR2315_SPI_READ_BASE + AR2315_SPI_READ_SIZE - 1,
-+ },
-+ {
-+ .name = "spiflash_mmr",
-+ .flags = IORESOURCE_MEM,
-+ .start = AR2315_SPI_MMR_BASE,
-+ .end = AR2315_SPI_MMR_BASE + AR2315_SPI_MMR_SIZE - 1,
-+ },
-+};
-+
-+static struct platform_device ar2315_spiflash = {
-+ .id = 0,
-+ .name = "ar2315-spiflash",
-+ .resource = ar2315_spiflash_res,
-+ .num_resources = ARRAY_SIZE(ar2315_spiflash_res)
-+};
-+
- void __init ar2315_init_devices(void)
- {
- /* Find board configuration */
-@@ -230,6 +252,8 @@ void __init ar2315_init_devices(void)
- ar2315_gpio_res[1].end = ar2315_gpio_res[1].start;
- platform_device_register(&ar2315_gpio);
-
-+ platform_device_register(&ar2315_spiflash);
-+
- ar2315_eth_data.macaddr = ath25_board.config->enet0_mac;
- ath25_add_ethernet(0, AR2315_ENET0_BASE, "eth0_mii",
- AR2315_ENET0_MII_BASE, AR2315_IRQ_ENET0,
+++ /dev/null
---- /dev/null
-+++ b/drivers/watchdog/ar2315-wtd.c
-@@ -0,0 +1,209 @@
-+/*
-+ * This program is free software; you can redistribute it and/or modify
-+ * it under the terms of the GNU General Public License as published by
-+ * the Free Software Foundation; either version 2 of the License, or
-+ * (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, see <http://www.gnu.org/licenses/>.
-+ *
-+ * Copyright (C) 2008 John Crispin <blogic@openwrt.org>
-+ * Based on EP93xx and ifxmips wdt driver
-+ */
-+
-+#include <linux/interrupt.h>
-+#include <linux/module.h>
-+#include <linux/moduleparam.h>
-+#include <linux/types.h>
-+#include <linux/miscdevice.h>
-+#include <linux/watchdog.h>
-+#include <linux/fs.h>
-+#include <linux/ioport.h>
-+#include <linux/notifier.h>
-+#include <linux/reboot.h>
-+#include <linux/init.h>
-+#include <linux/platform_device.h>
-+#include <linux/io.h>
-+#include <linux/uaccess.h>
-+
-+#define DRIVER_NAME "ar2315-wdt"
-+
-+#define CLOCK_RATE 40000000
-+#define HEARTBEAT(x) (x < 1 || x > 90 ? 20 : x)
-+
-+#define WDT_REG_TIMER 0x00
-+#define WDT_REG_CTRL 0x04
-+
-+#define WDT_CTRL_ACT_NONE 0x00000000 /* No action */
-+#define WDT_CTRL_ACT_NMI 0x00000001 /* NMI on watchdog */
-+#define WDT_CTRL_ACT_RESET 0x00000002 /* reset on watchdog */
-+
-+static int wdt_timeout = 20;
-+static int started;
-+static int in_use;
-+static void __iomem *wdt_base;
-+
-+static inline void ar2315_wdt_wr(unsigned reg, u32 val)
-+{
-+ iowrite32(val, wdt_base + reg);
-+}
-+
-+static void
-+ar2315_wdt_enable(void)
-+{
-+ ar2315_wdt_wr(WDT_REG_TIMER, wdt_timeout * CLOCK_RATE);
-+}
-+
-+static ssize_t
-+ar2315_wdt_write(struct file *file, const char __user *data, size_t len,
-+ loff_t *ppos)
-+{
-+ if (len)
-+ ar2315_wdt_enable();
-+ return len;
-+}
-+
-+static int
-+ar2315_wdt_open(struct inode *inode, struct file *file)
-+{
-+ if (in_use)
-+ return -EBUSY;
-+ ar2315_wdt_enable();
-+ in_use = 1;
-+ started = 1;
-+ return nonseekable_open(inode, file);
-+}
-+
-+static int
-+ar2315_wdt_release(struct inode *inode, struct file *file)
-+{
-+ in_use = 0;
-+ return 0;
-+}
-+
-+static irqreturn_t
-+ar2315_wdt_interrupt(int irq, void *dev)
-+{
-+ struct platform_device *pdev = (struct platform_device *)dev;
-+
-+ if (started) {
-+ dev_crit(&pdev->dev, "watchdog expired, rebooting system\n");
-+ emergency_restart();
-+ } else {
-+ ar2315_wdt_wr(WDT_REG_CTRL, 0);
-+ ar2315_wdt_wr(WDT_REG_TIMER, 0);
-+ }
-+ return IRQ_HANDLED;
-+}
-+
-+static struct watchdog_info ident = {
-+ .options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING,
-+ .identity = "ar2315 Watchdog",
-+};
-+
-+static long
-+ar2315_wdt_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
-+{
-+ int new_wdt_timeout;
-+ int ret = -ENOIOCTLCMD;
-+
-+ switch (cmd) {
-+ case WDIOC_GETSUPPORT:
-+ ret = copy_to_user((void __user *)arg, &ident, sizeof(ident)) ?
-+ -EFAULT : 0;
-+ break;
-+ case WDIOC_KEEPALIVE:
-+ ar2315_wdt_enable();
-+ ret = 0;
-+ break;
-+ case WDIOC_SETTIMEOUT:
-+ ret = get_user(new_wdt_timeout, (int __user *)arg);
-+ if (ret)
-+ break;
-+ wdt_timeout = HEARTBEAT(new_wdt_timeout);
-+ ar2315_wdt_enable();
-+ break;
-+ case WDIOC_GETTIMEOUT:
-+ ret = put_user(wdt_timeout, (int __user *)arg);
-+ break;
-+ }
-+ return ret;
-+}
-+
-+static const struct file_operations ar2315_wdt_fops = {
-+ .owner = THIS_MODULE,
-+ .llseek = no_llseek,
-+ .write = ar2315_wdt_write,
-+ .unlocked_ioctl = ar2315_wdt_ioctl,
-+ .open = ar2315_wdt_open,
-+ .release = ar2315_wdt_release,
-+};
-+
-+static struct miscdevice ar2315_wdt_miscdev = {
-+ .minor = WATCHDOG_MINOR,
-+ .name = "watchdog",
-+ .fops = &ar2315_wdt_fops,
-+};
-+
-+static int
-+ar2315_wdt_probe(struct platform_device *dev)
-+{
-+ struct resource *mem_res, *irq_res;
-+ int ret = 0;
-+
-+ if (wdt_base)
-+ return -EBUSY;
-+
-+ irq_res = platform_get_resource(dev, IORESOURCE_IRQ, 0);
-+ if (!irq_res) {
-+ dev_err(&dev->dev, "no IRQ resource\n");
-+ return -ENOENT;
-+ }
-+
-+ mem_res = platform_get_resource(dev, IORESOURCE_MEM, 0);
-+ wdt_base = devm_ioremap_resource(&dev->dev, mem_res);
-+ if (IS_ERR(wdt_base))
-+ return PTR_ERR(wdt_base);
-+
-+ ret = devm_request_irq(&dev->dev, irq_res->start, ar2315_wdt_interrupt,
-+ 0, DRIVER_NAME, dev);
-+ if (ret) {
-+ dev_err(&dev->dev, "failed to register inetrrupt\n");
-+ goto out;
-+ }
-+
-+ ret = misc_register(&ar2315_wdt_miscdev);
-+ if (ret)
-+ dev_err(&dev->dev, "failed to register miscdev\n");
-+
-+out:
-+ return ret;
-+}
-+
-+static int
-+ar2315_wdt_remove(struct platform_device *dev)
-+{
-+ misc_deregister(&ar2315_wdt_miscdev);
-+ return 0;
-+}
-+
-+static struct platform_driver ar2315_wdt_driver = {
-+ .probe = ar2315_wdt_probe,
-+ .remove = ar2315_wdt_remove,
-+ .driver = {
-+ .name = DRIVER_NAME,
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+module_platform_driver(ar2315_wdt_driver);
-+
-+MODULE_DESCRIPTION("Atheros AR2315 hardware watchdog driver");
-+MODULE_AUTHOR("John Crispin <blogic@openwrt.org>");
-+MODULE_LICENSE("GPL");
-+MODULE_ALIAS("platform:" DRIVER_NAME);
---- a/drivers/watchdog/Kconfig
-+++ b/drivers/watchdog/Kconfig
-@@ -1345,6 +1345,13 @@ config RALINK_WDT
- help
- Hardware driver for the Ralink SoC Watchdog Timer.
-
-+config AR2315_WDT
-+ tristate "Atheros AR2315+ WiSoCs Watchdog Timer"
-+ depends on ATH25
-+ help
-+ Hardware driver for the built-in watchdog timer on the Atheros
-+ AR2315/AR2316 WiSoCs.
-+
- # PARISC Architecture
-
- # POWERPC Architecture
---- a/drivers/watchdog/Makefile
-+++ b/drivers/watchdog/Makefile
-@@ -143,6 +143,7 @@ obj-$(CONFIG_WDT_MTX1) += mtx-1_wdt.o
- obj-$(CONFIG_PNX833X_WDT) += pnx833x_wdt.o
- obj-$(CONFIG_SIBYTE_WDOG) += sb_wdog.o
- obj-$(CONFIG_AR7_WDT) += ar7_wdt.o
-+obj-$(CONFIG_AR2315_WDT) += ar2315-wtd.o
- obj-$(CONFIG_TXX9_WDT) += txx9wdt.o
- obj-$(CONFIG_OCTEON_WDT) += octeon-wdt.o
- octeon-wdt-y := octeon-wdt-main.o octeon-wdt-nmi.o
---- a/arch/mips/ath25/ar2315.c
-+++ b/arch/mips/ath25/ar2315.c
-@@ -220,6 +220,24 @@ static struct platform_device ar2315_gpi
- .num_resources = ARRAY_SIZE(ar2315_gpio_res)
- };
-
-+static struct resource ar2315_wdt_res[] = {
-+ {
-+ .flags = IORESOURCE_MEM,
-+ .start = AR2315_RST_BASE + AR2315_WDT_TIMER,
-+ .end = AR2315_RST_BASE + AR2315_WDT_TIMER + 8 - 1,
-+ },
-+ {
-+ .flags = IORESOURCE_IRQ,
-+ }
-+};
-+
-+static struct platform_device ar2315_wdt = {
-+ .id = 0,
-+ .name = "ar2315-wdt",
-+ .resource = ar2315_wdt_res,
-+ .num_resources = ARRAY_SIZE(ar2315_wdt_res)
-+};
-+
- static struct resource ar2315_spiflash_res[] = {
- {
- .name = "spiflash_read",
-@@ -252,6 +270,11 @@ void __init ar2315_init_devices(void)
- ar2315_gpio_res[1].end = ar2315_gpio_res[1].start;
- platform_device_register(&ar2315_gpio);
-
-+ ar2315_wdt_res[1].start = irq_create_mapping(ar2315_misc_irq_domain,
-+ AR2315_MISC_IRQ_WATCHDOG);
-+ ar2315_wdt_res[1].end = ar2315_wdt_res[1].start;
-+ platform_device_register(&ar2315_wdt);
-+
- platform_device_register(&ar2315_spiflash);
-
- ar2315_eth_data.macaddr = ath25_board.config->enet0_mac;
+++ /dev/null
---- a/drivers/mtd/redboot.c
-+++ b/drivers/mtd/redboot.c
-@@ -30,6 +30,8 @@
- #include <linux/mtd/partitions.h>
- #include <linux/module.h>
-
-+#define BOARD_CONFIG_PART "boardconfig"
-+
- struct fis_image_desc {
- unsigned char name[16]; // Null terminated name
- uint32_t flash_base; // Address within FLASH of image
-@@ -60,6 +62,7 @@ static int parse_redboot_partitions(stru
- struct mtd_partition **pparts,
- struct mtd_part_parser_data *data)
- {
-+ unsigned long max_offset = 0;
- int nrparts = 0;
- struct fis_image_desc *buf;
- struct mtd_partition *parts;
-@@ -225,14 +228,15 @@ static int parse_redboot_partitions(stru
- }
- }
- #endif
-- parts = kzalloc(sizeof(*parts)*nrparts + nulllen + namelen, GFP_KERNEL);
-+ parts = kzalloc(sizeof(*parts) * (nrparts + 1) + nulllen + namelen +
-+ sizeof(BOARD_CONFIG_PART), GFP_KERNEL);
-
- if (!parts) {
- ret = -ENOMEM;
- goto out;
- }
-
-- nullname = (char *)&parts[nrparts];
-+ nullname = (char *)&parts[nrparts + 1];
- #ifdef CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED
- if (nulllen > 0) {
- strcpy(nullname, nullstring);
-@@ -251,6 +255,8 @@ static int parse_redboot_partitions(stru
- }
- #endif
- for ( ; i<nrparts; i++) {
-+ if (max_offset < buf[i].flash_base + buf[i].size)
-+ max_offset = buf[i].flash_base + buf[i].size;
- parts[i].size = fl->img->size;
- parts[i].offset = fl->img->flash_base;
- parts[i].name = names;
-@@ -284,6 +290,13 @@ static int parse_redboot_partitions(stru
- fl = fl->next;
- kfree(tmp_fl);
- }
-+ if (master->size - max_offset >= master->erasesize) {
-+ parts[nrparts].size = master->size - max_offset;
-+ parts[nrparts].offset = max_offset;
-+ parts[nrparts].name = names;
-+ strcpy(names, BOARD_CONFIG_PART);
-+ nrparts++;
-+ }
- ret = nrparts;
- *pparts = parts;
- out:
+++ /dev/null
---- a/drivers/mtd/redboot.c
-+++ b/drivers/mtd/redboot.c
-@@ -79,12 +79,18 @@ static int parse_redboot_partitions(stru
- static char nullstring[] = "unallocated";
- #endif
-
-+ buf = vmalloc(master->erasesize);
-+ if (!buf)
-+ return -ENOMEM;
-+
-+ restart:
- if ( directory < 0 ) {
- offset = master->size + directory * master->erasesize;
- while (mtd_block_isbad(master, offset)) {
- if (!offset) {
- nogood:
- printk(KERN_NOTICE "Failed to find a non-bad block to check for RedBoot partition table\n");
-+ vfree(buf);
- return -EIO;
- }
- offset -= master->erasesize;
-@@ -97,10 +103,6 @@ static int parse_redboot_partitions(stru
- goto nogood;
- }
- }
-- buf = vmalloc(master->erasesize);
--
-- if (!buf)
-- return -ENOMEM;
-
- printk(KERN_NOTICE "Searching for RedBoot partition table in %s at offset 0x%lx\n",
- master->name, offset);
-@@ -173,6 +175,11 @@ static int parse_redboot_partitions(stru
- }
- if (i == numslots) {
- /* Didn't find it */
-+ if (offset + master->erasesize < master->size) {
-+ /* not at the end of the flash yet, maybe next block */
-+ directory++;
-+ goto restart;
-+ }
- printk(KERN_NOTICE "No RedBoot partition table detected in %s\n",
- master->name);
- ret = 0;
+++ /dev/null
---- a/drivers/mtd/redboot.c
-+++ b/drivers/mtd/redboot.c
-@@ -58,6 +58,22 @@ static inline int redboot_checksum(struc
- return 1;
- }
-
-+static uint32_t mtd_get_offset_erasesize(struct mtd_info *mtd, uint64_t offset)
-+{
-+ struct mtd_erase_region_info *regions = mtd->eraseregions;
-+ int i;
-+
-+ for (i = 0; i < mtd->numeraseregions; i++) {
-+ if (regions[i].offset +
-+ regions[i].numblocks * regions[i].erasesize <= offset)
-+ continue;
-+
-+ return regions[i].erasesize;
-+ }
-+
-+ return mtd->erasesize;
-+}
-+
- static int parse_redboot_partitions(struct mtd_info *master,
- struct mtd_partition **pparts,
- struct mtd_part_parser_data *data)
-@@ -74,6 +90,7 @@ static int parse_redboot_partitions(stru
- int namelen = 0;
- int nulllen = 0;
- int numslots;
-+ int first_slot;
- unsigned long offset;
- #ifdef CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED
- static char nullstring[] = "unallocated";
-@@ -186,7 +203,10 @@ static int parse_redboot_partitions(stru
- goto out;
- }
-
-- for (i = 0; i < numslots; i++) {
-+ first_slot = (buf[i].flash_base & (master->erasesize - 1)) /
-+ sizeof(struct fis_image_desc);
-+
-+ for (i = first_slot; i < first_slot + numslots; i++) {
- struct fis_list *new_fl, **prev;
-
- if (buf[i].name[0] == 0xff) {
-@@ -262,12 +282,13 @@ static int parse_redboot_partitions(stru
- }
- #endif
- for ( ; i<nrparts; i++) {
-- if (max_offset < buf[i].flash_base + buf[i].size)
-- max_offset = buf[i].flash_base + buf[i].size;
- parts[i].size = fl->img->size;
- parts[i].offset = fl->img->flash_base;
- parts[i].name = names;
-
-+ if (max_offset < parts[i].offset + parts[i].size)
-+ max_offset = parts[i].offset + parts[i].size;
-+
- strcpy(names, fl->img->name);
- #ifdef CONFIG_MTD_REDBOOT_PARTS_READONLY
- if (!memcmp(names, "RedBoot", 8) ||
-@@ -297,7 +318,9 @@ static int parse_redboot_partitions(stru
- fl = fl->next;
- kfree(tmp_fl);
- }
-- if (master->size - max_offset >= master->erasesize) {
-+
-+ if (master->size - max_offset >=
-+ mtd_get_offset_erasesize(master, max_offset)) {
- parts[nrparts].size = master->size - max_offset;
- parts[nrparts].offset = max_offset;
- parts[nrparts].name = names;
+++ /dev/null
---- a/arch/mips/ath25/Makefile
-+++ b/arch/mips/ath25/Makefile
-@@ -8,7 +8,7 @@
- # Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
- #
-
--obj-y += board.o prom.o devices.o
-+obj-y += board.o prom.o devices.o reset.o
-
- obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
-
---- /dev/null
-+++ b/arch/mips/ath25/reset.c
-@@ -0,0 +1,57 @@
-+#include <linux/init.h>
-+#include <linux/slab.h>
-+#include <linux/platform_device.h>
-+#include <linux/gpio_keys.h>
-+#include <linux/input.h>
-+#include <ath25_platform.h>
-+#include "devices.h"
-+
-+static int __init
-+ar231x_init_reset(void)
-+{
-+ struct platform_device *pdev;
-+ struct gpio_keys_platform_data pdata;
-+ struct gpio_keys_button *p;
-+ int err;
-+
-+ if (ath25_board.config->reset_config_gpio == 0xffff)
-+ return -ENODEV;
-+
-+ p = kzalloc(sizeof(*p), GFP_KERNEL);
-+ if (!p)
-+ goto err;
-+
-+ p->desc = "reset";
-+ p->type = EV_KEY;
-+ p->code = KEY_RESTART;
-+ p->debounce_interval = 60;
-+ p->gpio = ath25_board.config->reset_config_gpio;
-+
-+ memset(&pdata, 0, sizeof(pdata));
-+ pdata.poll_interval = 20;
-+ pdata.buttons = p;
-+ pdata.nbuttons = 1;
-+
-+ pdev = platform_device_alloc("gpio-keys-polled", 0);
-+ if (!pdev)
-+ goto err_free;
-+
-+ err = platform_device_add_data(pdev, &pdata, sizeof(pdata));
-+ if (err)
-+ goto err_put_pdev;
-+
-+ err = platform_device_add(pdev);
-+ if (err)
-+ goto err_put_pdev;
-+
-+ return 0;
-+
-+err_put_pdev:
-+ platform_device_put(pdev);
-+err_free:
-+ kfree(p);
-+err:
-+ return -ENOMEM;
-+}
-+
-+module_init(ar231x_init_reset);
+++ /dev/null
---- a/drivers/net/ethernet/atheros/ar231x/ar231x.c
-+++ b/drivers/net/ethernet/atheros/ar231x/ar231x.c
-@@ -135,6 +135,7 @@ static int ar231x_mdiobus_write(struct m
- static int ar231x_mdiobus_reset(struct mii_bus *bus);
- static int ar231x_mdiobus_probe(struct net_device *dev);
- static void ar231x_adjust_link(struct net_device *dev);
-+static bool no_phy;
-
- #ifndef ERR
- #define ERR(fmt, args...) printk("%s: " fmt, __func__, ##args)
-@@ -167,6 +168,32 @@ static const struct net_device_ops ar231
- #endif
- };
-
-+static int get_phy_id(struct mii_bus *bus, int addr, u32 *phy_id)
-+{
-+ int phy_reg;
-+
-+ /**
-+ * Grab the bits from PHYIR1, and put them
-+ * in the upper half.
-+ */
-+ phy_reg = mdiobus_read(bus, addr, MII_PHYSID1);
-+
-+ if (phy_reg < 0)
-+ return -EIO;
-+
-+ *phy_id = (phy_reg & 0xffff) << 16;
-+
-+ /* Grab the bits from PHYIR2, and put them in the lower half */
-+ phy_reg = mdiobus_read(bus, addr, MII_PHYSID2);
-+
-+ if (phy_reg < 0)
-+ return -EIO;
-+
-+ *phy_id |= (phy_reg & 0xffff);
-+
-+ return 0;
-+}
-+
- static int ar231x_probe(struct platform_device *pdev)
- {
- struct net_device *dev;
-@@ -273,6 +300,24 @@ static int ar231x_probe(struct platform_
-
- mdiobus_register(sp->mii_bus);
-
-+ /**
-+ * Workaround for Micrel switch, which is only available on
-+ * one PHY and cannot be configured through MDIO.
-+ */
-+ if (!no_phy) {
-+ u32 phy_id = 0;
-+
-+ get_phy_id(sp->mii_bus, 1, &phy_id);
-+ if (phy_id == 0x00221450)
-+ no_phy = true;
-+ }
-+ if (no_phy) {
-+ sp->link = 1;
-+ netif_carrier_on(dev);
-+ return 0;
-+ }
-+ no_phy = true;
-+
- if (ar231x_mdiobus_probe(dev) != 0) {
- printk(KERN_ERR "%s: mdiobus_probe failed\n", dev->name);
- rx_tasklet_cleanup(dev);
-@@ -329,8 +374,10 @@ static int ar231x_remove(struct platform
- rx_tasklet_cleanup(dev);
- ar231x_init_cleanup(dev);
- unregister_netdev(dev);
-- mdiobus_unregister(sp->mii_bus);
-- mdiobus_free(sp->mii_bus);
-+ if (sp->mii_bus) {
-+ mdiobus_unregister(sp->mii_bus);
-+ mdiobus_free(sp->mii_bus);
-+ }
- kfree(dev);
- return 0;
- }
-@@ -1079,6 +1126,9 @@ static int ar231x_ioctl(struct net_devic
- {
- struct ar231x_private *sp = netdev_priv(dev);
-
-+ if (!sp->phy_dev)
-+ return -ENODEV;
-+
- switch (cmd) {
- case SIOCGMIIPHY:
- case SIOCGMIIREG:
+++ /dev/null
---- a/arch/mips/ath25/ar2315.c
-+++ b/arch/mips/ath25/ar2315.c
-@@ -23,6 +23,7 @@
- #include <linux/reboot.h>
- #include <linux/delay.h>
- #include <linux/gpio.h>
-+#include <linux/leds.h>
- #include <asm/bootinfo.h>
- #include <asm/reboot.h>
- #include <asm/time.h>
-@@ -260,6 +261,50 @@ static struct platform_device ar2315_spi
- .num_resources = ARRAY_SIZE(ar2315_spiflash_res)
- };
-
-+#ifdef CONFIG_LEDS_GPIO
-+static struct gpio_led ar2315_leds[6];
-+static struct gpio_led_platform_data ar2315_led_data = {
-+ .leds = (void *)ar2315_leds,
-+};
-+
-+static struct platform_device ar2315_gpio_leds = {
-+ .name = "leds-gpio",
-+ .id = -1,
-+ .dev = {
-+ .platform_data = (void *)&ar2315_led_data,
-+ }
-+};
-+
-+static void __init ar2315_init_gpio_leds(void)
-+{
-+ static char led_names[6][6];
-+ int i, led = 0;
-+
-+ ar2315_led_data.num_leds = 0;
-+ for (i = 1; i < 8; i++) {
-+ if ((i == AR2315_RESET_GPIO) ||
-+ (i == ath25_board.config->reset_config_gpio))
-+ continue;
-+
-+ if (i == ath25_board.config->sys_led_gpio)
-+ strcpy(led_names[led], "wlan");
-+ else
-+ sprintf(led_names[led], "gpio%d", i);
-+
-+ ar2315_leds[led].name = led_names[led];
-+ ar2315_leds[led].gpio = i;
-+ ar2315_leds[led].active_low = 0;
-+ led++;
-+ }
-+ ar2315_led_data.num_leds = led;
-+ platform_device_register(&ar2315_gpio_leds);
-+}
-+#else
-+static inline void ar2315_init_gpio_leds(void)
-+{
-+}
-+#endif
-+
- void __init ar2315_init_devices(void)
- {
- /* Find board configuration */
-@@ -270,6 +315,8 @@ void __init ar2315_init_devices(void)
- ar2315_gpio_res[1].end = ar2315_gpio_res[1].start;
- platform_device_register(&ar2315_gpio);
-
-+ ar2315_init_gpio_leds();
-+
- ar2315_wdt_res[1].start = irq_create_mapping(ar2315_misc_irq_domain,
- AR2315_MISC_IRQ_WATCHDOG);
- ar2315_wdt_res[1].end = ar2315_wdt_res[1].start;
---- a/arch/mips/ath25/ar5312.c
-+++ b/arch/mips/ath25/ar5312.c
-@@ -23,6 +23,7 @@
- #include <linux/mtd/physmap.h>
- #include <linux/reboot.h>
- #include <linux/gpio.h>
-+#include <linux/leds.h>
- #include <asm/bootinfo.h>
- #include <asm/reboot.h>
- #include <asm/time.h>
-@@ -231,6 +232,23 @@ static struct platform_device ar5312_gpi
- .num_resources = ARRAY_SIZE(ar5312_gpio_res),
- };
-
-+#ifdef CONFIG_LEDS_GPIO
-+static struct gpio_led ar5312_leds[] = {
-+ { .name = "wlan", .gpio = 0, .active_low = 1, },
-+};
-+
-+static const struct gpio_led_platform_data ar5312_led_data = {
-+ .num_leds = ARRAY_SIZE(ar5312_leds),
-+ .leds = (void *)ar5312_leds,
-+};
-+
-+static struct platform_device ar5312_gpio_leds = {
-+ .name = "leds-gpio",
-+ .id = -1,
-+ .dev.platform_data = (void *)&ar5312_led_data,
-+};
-+#endif
-+
- static void __init ar5312_flash_init(void)
- {
- void __iomem *flashctl_base;
-@@ -301,6 +319,11 @@ void __init ar5312_init_devices(void)
-
- platform_device_register(&ar5312_gpio);
-
-+#ifdef CONFIG_LEDS_GPIO
-+ ar5312_leds[0].gpio = config->sys_led_gpio;
-+ platform_device_register(&ar5312_gpio_leds);
-+#endif
-+
- /* Fix up MAC addresses if necessary */
- if (is_broadcast_ether_addr(config->enet0_mac))
- ether_addr_copy(config->enet0_mac, config->enet1_mac);
projects / openwrt / staging / chunkeey.git / commitdiff