target/linux/ath79/dts/qca9531_yuncore_a770.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca953x.dtsi"
   8
   9 / {
  10         model = "YunCore A770";
  11         compatible = "yuncore,a770", "qca,qca9533";
  12
  13         aliases {
  14                 led-boot = &status;
  15                 led-failsafe = &status;
  16                 led-running = &status;
  17                 led-upgrade = &status;
  18         };
  19
  20         chosen {
  21                 bootargs = "console=ttyS0,115200n8";
  22         };
  23
  24         keys {
  25                 compatible = "gpio-keys";
  26
  27                 reset {
  28                         label = "reset";
  29                         linux,code = <KEY_RESTART>;
  30                         gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
  31                         debounce-interval = <60>;
  32                 };
  33         };
  34
  35         leds {
  36                 compatible = "gpio-leds";
  37
  38                 lan {
  39                         label = "a770:green:lan";
  40                         gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
  41                 };
  42
  43                 status: status {
  44                         label = "a770:green:status";
  45                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  46                         default-state = "keep";
  47                 };
  48
  49                 wan {
  50                         label = "a770:green:wan";
  51                         gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
  52                 };
  53
  54                 wlan2g {
  55                         label = "a770:red:wlan2g";
  56                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  57                         linux,default-trigger = "phy1tpt";
  58                 };
  59         };
  60 };
  61
  62 &eth0 {
  63         status = "okay";
  64
  65         phy-handle = <&swphy4>;
  66         mtd-mac-address = <&art 0x0>;
  67 };
  68
  69 &eth1 {
  70         mtd-mac-address = <&art 0x6>;
  71 };
  72
  73 &pcie0 {
  74         status = "okay";
  75 };
  76
  77 &spi {
  78         status = "okay";
  79
  80         num-cs = <1>;
  81
  82         flash@0 {
  83                 compatible = "jedec,spi-nor";
  84                 reg = <0>;
  85                 spi-max-frequency = <25000000>;
  86
  87                 partitions {
  88                         compatible = "fixed-partitions";
  89                         #address-cells = <1>;
  90                         #size-cells = <1>;
  91
  92                         partition@0 {
  93                                 label = "u-boot";
  94                                 reg = <0x000000 0x040000>;
  95                                 read-only;
  96                         };
  97
  98                         partition@40000 {
  99                                 label = "u-boot-env";
 100                                 reg = <0x040000 0x010000>;
 101                         };
 102
 103                         partition@50000 {
 104                                 compatible = "denx,uimage";
 105                                 label = "firmware";
 106                                 reg = <0x050000 0xfa0000>;
 107                         };
 108
 109                         art: partition@ff0000 {
 110                                 label = "art";
 111                                 reg = <0xff0000 0x010000>;
 112                                 read-only;
 113                         };
 114                 };
 115         };
 116 };
 117
 118 &uart {
 119         status = "okay";
 120 };
 121
 122 &wmac {
 123         status = "okay";
 124
 125         mtd-cal-data = <&art 0x1000>;
 126 };