target/linux/brcm63xx/patches-4.1/511-board_V2500V.patch

   1 --- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
   2 +++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
   3 @@ -715,6 +715,27 @@ static struct board_info __initdata boar
   4                 .ext_irq                = 2,
   5         },
   6  };
   7 +
   8 +static struct board_info __initdata board_V2500V_BB = {
   9 +       .name                           = "V2500V_BB",
  10 +        .expected_cpu_id                = 0x6348,
  11 +
  12 +        .has_uart0                      = 1,
  13 +        .has_enet0                      = 1,
  14 +        .has_enet1                      = 1,
  15 +        .has_pci                        = 1,
  16 +
  17 +        .enet0 = {
  18 +                .has_phy                = 1,
  19 +                .use_internal_phy       = 1,
  20 +        },
  21 +        .enet1 = {
  22 +               .has_phy                = 1,
  23 +               .phy_id                 = 0,
  24 +                .force_speed_100        = 1,
  25 +                .force_duplex_full      = 1,
  26 +       },
  27 +};
  28  #endif /* CONFIG_BCM63XX_CPU_6348 */
  29
  30  /*
  31 @@ -1047,6 +1068,7 @@ static const struct board_info __initcon
  32         &board_96348_D4PW,
  33         &board_spw500v,
  34         &board_96348sv,
  35 +       &board_V2500V_BB,
  36  #endif
  37
  38  #ifdef CONFIG_BCM63XX_CPU_6358
  39 @@ -1086,6 +1108,7 @@ static struct of_device_id const bcm963x
  40         { .compatible = "brcm,bcm96348gw-10", .data = &board_96348gw_10, },
  41         { .compatible = "brcm,bcm96348gw-11", .data = &board_96348gw_11, },
  42         { .compatible = "brcm,bcm96348gw-a", .data = &board_96348gw_a, },
  43 +       { .compatible = "bt,v2500v-bb", .data = &board_V2500V_BB, },
  44         { .compatible = "d-link,dsl-2640b-b", .data = &board_96348_D4PW, },
  45         { .compatible = "davolink,dv-201amr", .data = &board_DV201AMR, },
  46         { .compatible = "dynalink,rta1025w", .data = &board_rta1025w_16, },
  47 @@ -1145,6 +1168,22 @@ void __init board_bcm963xx_init(void)
  48                 val &= MPI_CSBASE_BASE_MASK;
  49         }
  50         boot_addr = (u8 *)KSEG1ADDR(val);
  51 +       printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr);
  52 +
  53 +       /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
  54 +       /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
  55 +       /* Loading firmware from the CFE Prompt always loads to Bank 0 */
  56 +       /* Do an early check of CFE and then select bank 0 */
  57 +
  58 +       if (boot_addr == (u8 *)0xbf800000) {
  59 +               u8 *tmp_boot_addr = (u8*)0xbfc00000;
  60 +
  61 +               bcm63xx_nvram_init(tmp_boot_addr + BCM963XX_NVRAM_OFFSET);
  62 +               if (!strcmp(bcm63xx_nvram_get_name(), "V2500V_BB")) {
  63 +                       printk(KERN_INFO PFX "V2500V: nvram bank 0\n");
  64 +                       boot_addr = tmp_boot_addr;
  65 +               }
  66 +       }
  67
  68         /* dump cfe version */
  69         cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
  70 --- a/arch/mips/bcm63xx/dev-flash.c
  71 +++ b/arch/mips/bcm63xx/dev-flash.c
  72 @@ -20,6 +20,7 @@
  73  #include <linux/spi/spi.h>
  74  #include <linux/spi/flash.h>
  75
  76 +#include <bcm63xx_board.h>
  77  #include <bcm63xx_cpu.h>
  78  #include <bcm63xx_dev_flash.h>
  79  #include <bcm63xx_dev_hsspi.h>
  80 @@ -234,6 +235,13 @@ int __init bcm63xx_flash_register(int nu
  81                         val = bcm_mpi_readl(MPI_CSBASE_REG(0));
  82                         val &= MPI_CSBASE_BASE_MASK;
  83
  84 +                       /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
  85 +                       /* Loading from CFE always uses Bank 0 */
  86 +                       if (!strcmp(board_get_name(), "V2500V_BB")) {
  87 +                               pr_info("V2500V: Start in Bank 0\n");
  88 +                               val = val + 0x400000; // Select Bank 0 start address
  89 +                       }
  90 +
  91                         mtd_resources[0].start = val;
  92                         mtd_resources[0].end = 0x1FFFFFFF;
  93                 }