--- a/nl80211.h
+++ b/nl80211.h
-@@ -503,6 +503,9 @@
- * TX status event pertaining to the TX request.
- * %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the
- * management frames at CCK rate or not in 2GHz band.
-+ * %NL80211_ATTR_CSA_C_OFFSETS_TX is an array of offsets to CSA
-+ * counters which will be updated to the current value. This attribute
-+ * is used during CSA period.
- * @NL80211_CMD_FRAME_WAIT_CANCEL: When an off-channel TX was requested, this
- * command may be used with the corresponding cookie to cancel the wait
- * time if it is known that it is no longer necessary.
-@@ -719,6 +722,22 @@
- * QoS mapping is relevant for IP packets, it is only valid during an
- * association. This is cleared on disassociation and AP restart.
+@@ -2299,6 +2299,12 @@ enum nl80211_commands {
+ * This is also used for capability advertisement in the wiphy information,
+ * with the appropriate sub-attributes.
*
-+ * @NL80211_CMD_ADD_TX_TS: Ask the kernel to add a traffic stream for the given
-+ * %NL80211_ATTR_TSID and %NL80211_ATTR_MAC with %NL80211_ATTR_USER_PRIO
-+ * and %NL80211_ATTR_ADMITTED_TIME parameters.
-+ * Note that the action frame handshake with the AP shall be handled by
-+ * userspace via the normal management RX/TX framework, this only sets
-+ * up the TX TS in the driver/device.
-+ * If the admitted time attribute is not added then the request just checks
-+ * if a subsequent setup could be successful, the intent is to use this to
-+ * avoid setting up a session with the AP when local restrictions would
-+ * make that impossible. However, the subsequent "real" setup may still
-+ * fail even if the check was successful.
-+ * @NL80211_CMD_DEL_TX_TS: Remove an existing TS with the %NL80211_ATTR_TSID
-+ * and %NL80211_ATTR_MAC parameters. It isn't necessary to call this
-+ * before removing a station entry entirely, or before disassociating
-+ * or similar, cleanup will happen in the driver/device in this case.
-+ *
- * @NL80211_CMD_MAX: highest used command number
- * @__NL80211_CMD_AFTER_LAST: internal use
- */
-@@ -890,6 +909,9 @@ enum nl80211_commands {
-
- NL80211_CMD_SET_QOS_MAP,
-
-+ NL80211_CMD_ADD_TX_TS,
-+ NL80211_CMD_DEL_TX_TS,
-+
- /* add new commands above here */
-
- /* used to define NL80211_CMD_MAX below */
-@@ -1525,10 +1547,10 @@ enum nl80211_commands {
- * operation).
- * @NL80211_ATTR_CSA_IES: Nested set of attributes containing the IE information
- * for the time while performing a channel switch.
-- * @NL80211_ATTR_CSA_C_OFF_BEACON: Offset of the channel switch counter
-- * field in the beacons tail (%NL80211_ATTR_BEACON_TAIL).
-- * @NL80211_ATTR_CSA_C_OFF_PRESP: Offset of the channel switch counter
-- * field in the probe response (%NL80211_ATTR_PROBE_RESP).
-+ * @NL80211_ATTR_CSA_C_OFF_BEACON: An array of offsets (u16) to the channel
-+ * switch counters in the beacons tail (%NL80211_ATTR_BEACON_TAIL).
-+ * @NL80211_ATTR_CSA_C_OFF_PRESP: An array of offsets (u16) to the channel
-+ * switch counters in the probe response (%NL80211_ATTR_PROBE_RESP).
- *
- * @NL80211_ATTR_RXMGMT_FLAGS: flags for nl80211_send_mgmt(), u32.
- * As specified in the &enum nl80211_rxmgmt_flags.
-@@ -1576,9 +1598,49 @@ enum nl80211_commands {
- * advertise values that cannot always be met. In such cases, an attempt
- * to add a new station entry with @NL80211_CMD_NEW_STATION may fail.
- *
-+ * @NL80211_ATTR_CSA_C_OFFSETS_TX: An array of csa counter offsets (u16) which
-+ * should be updated when the frame is transmitted.
-+ * @NL80211_ATTR_MAX_CSA_COUNTERS: U8 attribute used to advertise the maximum
-+ * supported number of csa counters.
-+ *
- * @NL80211_ATTR_TDLS_PEER_CAPABILITY: flags for TDLS peer capabilities, u32.
- * As specified in the &enum nl80211_tdls_peer_capability.
- *
-+ * @NL80211_ATTR_IFACE_SOCKET_OWNER: flag attribute, if set during interface
-+ * creation then the new interface will be owned by the netlink socket
-+ * that created it and will be destroyed when the socket is closed
-+ *
-+ * @NL80211_ATTR_TDLS_INITIATOR: flag attribute indicating the current end is
-+ * the TDLS link initiator.
-+ *
-+ * @NL80211_ATTR_USE_RRM: flag for indicating whether the current connection
-+ * shall support Radio Resource Measurements (11k). This attribute can be
-+ * used with %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests.
-+ * User space applications are expected to use this flag only if the
-+ * underlying device supports these minimal RRM features:
-+ * %NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES,
-+ * %NL80211_FEATURE_QUIET,
-+ * If this flag is used, driver must add the Power Capabilities IE to the
-+ * association request. In addition, it must also set the RRM capability
-+ * flag in the association request's Capability Info field.
-+ *
-+ * @NL80211_ATTR_WIPHY_DYN_ACK: flag attribute used to enable ACK timeout
-+ * estimation algorithm (dynack). In order to activate dynack
-+ * %NL80211_FEATURE_ACKTO_ESTIMATION feature flag must be set by lower
-+ * drivers to indicate dynack capability. Dynack is automatically disabled
-+ * setting valid value for coverage class.
-+ *
-+ * @NL80211_ATTR_TSID: a TSID value (u8 attribute)
-+ * @NL80211_ATTR_USER_PRIO: user priority value (u8 attribute)
-+ * @NL80211_ATTR_ADMITTED_TIME: admitted time in units of 32 microseconds
-+ * (per second) (u16 attribute)
-+ *
-+ * @NL80211_ATTR_SMPS_MODE: SMPS mode to use (ap mode). see
-+ * &enum nl80211_smps_mode.
++ * @NL80211_ATTR_AIRTIME_WEIGHT: Station's weight when scheduled by the airtime
++ * scheduler.
+ *
+ * @NL80211_ATTR_WIPHY_ANTENNA_GAIN: Configured antenna gain. Used to reduce
+ * transmit power to stay within regulatory limits. u32, dBi.
+ *
+ * @NUM_NL80211_ATTR: total number of nl80211_attrs available
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
- */
-@@ -1914,6 +1976,25 @@ enum nl80211_attrs {
+@@ -2748,6 +2754,10 @@ enum nl80211_attrs {
- NL80211_ATTR_TDLS_PEER_CAPABILITY,
+ NL80211_ATTR_PEER_MEASUREMENTS,
-+ NL80211_ATTR_IFACE_SOCKET_OWNER,
-+
-+ NL80211_ATTR_CSA_C_OFFSETS_TX,
-+ NL80211_ATTR_MAX_CSA_COUNTERS,
-+
-+ NL80211_ATTR_TDLS_INITIATOR,
-+
-+ NL80211_ATTR_USE_RRM,
-+
-+ NL80211_ATTR_WIPHY_DYN_ACK,
-+
-+ NL80211_ATTR_TSID,
-+ NL80211_ATTR_USER_PRIO,
-+ NL80211_ATTR_ADMITTED_TIME,
-+
-+ NL80211_ATTR_SMPS_MODE,
++ NL80211_ATTR_AIRTIME_WEIGHT,
+
+ NL80211_ATTR_WIPHY_ANTENNA_GAIN,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
-@@ -2182,6 +2263,8 @@ enum nl80211_sta_bss_param {
- * Contains a nested array of signal strength attributes (u8, dBm)
- * @NL80211_STA_INFO_CHAIN_SIGNAL_AVG: per-chain signal strength average
- * Same format as NL80211_STA_INFO_CHAIN_SIGNAL.
-+ * @NL80211_STA_EXPECTED_THROUGHPUT: expected throughput considering also the
-+ * 802.11 header (u32, kbps)
+@@ -3125,6 +3135,9 @@ enum nl80211_sta_bss_param {
+ * might not be fully accurate.
+ * @NL80211_STA_INFO_CONNECTED_TO_GATE: set to true if STA has a path to a
+ * mesh gate (u8, 0 or 1)
++ * @NL80211_STA_INFO_TX_DURATION: aggregate PPDU duration for all frames
++ * sent to the station (u64, usec)
++ * @NL80211_STA_INFO_AIRTIME_WEIGHT: current airtime weight for station (u16)
* @__NL80211_STA_INFO_AFTER_LAST: internal
* @NL80211_STA_INFO_MAX: highest possible station info attribute
*/
-@@ -2213,6 +2296,7 @@ enum nl80211_sta_info {
- NL80211_STA_INFO_TX_BYTES64,
- NL80211_STA_INFO_CHAIN_SIGNAL,
- NL80211_STA_INFO_CHAIN_SIGNAL_AVG,
-+ NL80211_STA_INFO_EXPECTED_THROUGHPUT,
+@@ -3168,6 +3181,8 @@ enum nl80211_sta_info {
+ NL80211_STA_INFO_RX_MPDUS,
+ NL80211_STA_INFO_FCS_ERROR_COUNT,
+ NL80211_STA_INFO_CONNECTED_TO_GATE,
++ NL80211_STA_INFO_TX_DURATION,
++ NL80211_STA_INFO_AIRTIME_WEIGHT,
/* keep last */
__NL80211_STA_INFO_AFTER_LAST,
-@@ -2336,9 +2420,34 @@ enum nl80211_band_attr {
- * using this channel as the primary or any of the secondary channels
- * isn't possible
- * @NL80211_FREQUENCY_ATTR_DFS_CAC_TIME: DFS CAC time in milliseconds.
-+ * @NL80211_FREQUENCY_ATTR_INDOOR_ONLY: Only indoor use is permitted on this
-+ * channel. A channel that has the INDOOR_ONLY attribute can only be
-+ * used when there is a clear assessment that the device is operating in
-+ * an indoor surroundings, i.e., it is connected to AC power (and not
-+ * through portable DC inverters) or is under the control of a master
-+ * that is acting as an AP and is connected to AC power.
-+ * @NL80211_FREQUENCY_ATTR_GO_CONCURRENT: GO operation is allowed on this
-+ * channel if it's connected concurrently to a BSS on the same channel on
-+ * the 2 GHz band or to a channel in the same UNII band (on the 5 GHz
-+ * band), and IEEE80211_CHAN_RADAR is not set. Instantiating a GO on a
-+ * channel that has the GO_CONCURRENT attribute set can be done when there
-+ * is a clear assessment that the device is operating under the guidance of
-+ * an authorized master, i.e., setting up a GO while the device is also
-+ * connected to an AP with DFS and radar detection on the UNII band (it is
-+ * up to user-space, i.e., wpa_supplicant to perform the required
-+ * verifications)
-+ * @NL80211_FREQUENCY_ATTR_NO_20MHZ: 20 MHz operation is not allowed
-+ * on this channel in current regulatory domain.
-+ * @NL80211_FREQUENCY_ATTR_NO_10MHZ: 10 MHz operation is not allowed
-+ * on this channel in current regulatory domain.
- * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
- * currently defined
- * @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
-+ *
-+ * See https://apps.fcc.gov/eas/comments/GetPublishedDocument.html?id=327&tn=528122
-+ * for more information on the FCC description of the relaxations allowed
-+ * by NL80211_FREQUENCY_ATTR_INDOOR_ONLY and
-+ * NL80211_FREQUENCY_ATTR_GO_CONCURRENT.
- */
- enum nl80211_frequency_attr {
- __NL80211_FREQUENCY_ATTR_INVALID,
-@@ -2355,6 +2464,10 @@ enum nl80211_frequency_attr {
- NL80211_FREQUENCY_ATTR_NO_80MHZ,
- NL80211_FREQUENCY_ATTR_NO_160MHZ,
- NL80211_FREQUENCY_ATTR_DFS_CAC_TIME,
-+ NL80211_FREQUENCY_ATTR_INDOOR_ONLY,
-+ NL80211_FREQUENCY_ATTR_GO_CONCURRENT,
-+ NL80211_FREQUENCY_ATTR_NO_20MHZ,
-+ NL80211_FREQUENCY_ATTR_NO_10MHZ,
-
- /* keep last */
- __NL80211_FREQUENCY_ATTR_AFTER_LAST,
-@@ -2573,10 +2686,13 @@ enum nl80211_dfs_regions {
- * present has been registered with the wireless core that
- * has listed NL80211_FEATURE_CELL_BASE_REG_HINTS as a
- * supported feature.
-+ * @NL80211_USER_REG_HINT_INDOOR: a user sent an hint indicating that the
-+ * platform is operating in an indoor environment.
- */
- enum nl80211_user_reg_hint_type {
- NL80211_USER_REG_HINT_USER = 0,
- NL80211_USER_REG_HINT_CELL_BASE = 1,
-+ NL80211_USER_REG_HINT_INDOOR = 2,
- };
-
- /**
-@@ -2998,14 +3114,20 @@ enum nl80211_bss_scan_width {
- * @NL80211_BSS_BSSID: BSSID of the BSS (6 octets)
- * @NL80211_BSS_FREQUENCY: frequency in MHz (u32)
- * @NL80211_BSS_TSF: TSF of the received probe response/beacon (u64)
-+ * (if @NL80211_BSS_PRESP_DATA is present then this is known to be
-+ * from a probe response, otherwise it may be from the same beacon
-+ * that the NL80211_BSS_BEACON_TSF will be from)
- * @NL80211_BSS_BEACON_INTERVAL: beacon interval of the (I)BSS (u16)
- * @NL80211_BSS_CAPABILITY: capability field (CPU order, u16)
- * @NL80211_BSS_INFORMATION_ELEMENTS: binary attribute containing the
- * raw information elements from the probe response/beacon (bin);
-- * if the %NL80211_BSS_BEACON_IES attribute is present, the IEs here are
-- * from a Probe Response frame; otherwise they are from a Beacon frame.
-+ * if the %NL80211_BSS_BEACON_IES attribute is present and the data is
-+ * different then the IEs here are from a Probe Response frame; otherwise
-+ * they are from a Beacon frame.
- * However, if the driver does not indicate the source of the IEs, these
- * IEs may be from either frame subtype.
-+ * If present, the @NL80211_BSS_PRESP_DATA attribute indicates that the
-+ * data here is known to be from a probe response, without any heuristics.
- * @NL80211_BSS_SIGNAL_MBM: signal strength of probe response/beacon
- * in mBm (100 * dBm) (s32)
- * @NL80211_BSS_SIGNAL_UNSPEC: signal strength of the probe response/beacon
-@@ -3017,6 +3139,10 @@ enum nl80211_bss_scan_width {
- * yet been received
- * @NL80211_BSS_CHAN_WIDTH: channel width of the control channel
- * (u32, enum nl80211_bss_scan_width)
-+ * @NL80211_BSS_BEACON_TSF: TSF of the last received beacon (u64)
-+ * (not present if no beacon frame has been received yet)
-+ * @NL80211_BSS_PRESP_DATA: the data in @NL80211_BSS_INFORMATION_ELEMENTS and
-+ * @NL80211_BSS_TSF is known to be from a probe response (flag attribute)
- * @__NL80211_BSS_AFTER_LAST: internal
- * @NL80211_BSS_MAX: highest BSS attribute
- */
-@@ -3034,6 +3160,8 @@ enum nl80211_bss {
- NL80211_BSS_SEEN_MS_AGO,
- NL80211_BSS_BEACON_IES,
- NL80211_BSS_CHAN_WIDTH,
-+ NL80211_BSS_BEACON_TSF,
-+ NL80211_BSS_PRESP_DATA,
-
- /* keep last */
- __NL80211_BSS_AFTER_LAST,
-@@ -3650,6 +3778,8 @@ enum nl80211_iface_limit_attrs {
- * different channels may be used within this group.
- * @NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS: u32 attribute containing the bitmap
- * of supported channel widths for radar detection.
-+ * @NL80211_IFACE_COMB_RADAR_DETECT_REGIONS: u32 attribute containing the bitmap
-+ * of supported regulatory regions for radar detection.
- * @NUM_NL80211_IFACE_COMB: number of attributes
- * @MAX_NL80211_IFACE_COMB: highest attribute number
- *
-@@ -3683,6 +3813,7 @@ enum nl80211_if_combination_attrs {
- NL80211_IFACE_COMB_STA_AP_BI_MATCH,
- NL80211_IFACE_COMB_NUM_CHANNELS,
- NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS,
-+ NL80211_IFACE_COMB_RADAR_DETECT_REGIONS,
-
- /* keep last */
- NUM_NL80211_IFACE_COMB,
-@@ -3893,6 +4024,29 @@ enum nl80211_ap_sme_features {
- * interface. An active monitor interface behaves like a normal monitor
- * interface, but gets added to the driver. It ensures that incoming
- * unicast packets directed at the configured interface address get ACKed.
-+ * @NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE: This driver supports dynamic
-+ * channel bandwidth change (e.g., HT 20 <-> 40 MHz channel) during the
-+ * lifetime of a BSS.
-+ * @NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES: This device adds a DS Parameter
-+ * Set IE to probe requests.
-+ * @NL80211_FEATURE_WFA_TPC_IE_IN_PROBES: This device adds a WFA TPC Report IE
-+ * to probe requests.
-+ * @NL80211_FEATURE_QUIET: This device, in client mode, supports Quiet Period
-+ * requests sent to it by an AP.
-+ * @NL80211_FEATURE_TX_POWER_INSERTION: This device is capable of inserting the
-+ * current tx power value into the TPC Report IE in the spectrum
-+ * management TPC Report action frame, and in the Radio Measurement Link
-+ * Measurement Report action frame.
-+ * @NL80211_FEATURE_ACKTO_ESTIMATION: This driver supports dynamic ACK timeout
-+ * estimation (dynack). %NL80211_ATTR_WIPHY_DYN_ACK flag attribute is used
-+ * to enable dynack.
-+ * @NL80211_FEATURE_STATIC_SMPS: Device supports static spatial
-+ * multiplexing powersave, ie. can turn off all but one chain
-+ * even on HT connections that should be using more chains.
-+ * @NL80211_FEATURE_DYNAMIC_SMPS: Device supports dynamic spatial
-+ * multiplexing powersave, ie. can turn off all but one chain
-+ * and then wake the rest up as required after, for example,
-+ * rts/cts handshake.
- */
- enum nl80211_feature_flags {
- NL80211_FEATURE_SK_TX_STATUS = 1 << 0,
-@@ -3913,6 +4067,14 @@ enum nl80211_feature_flags {
- NL80211_FEATURE_FULL_AP_CLIENT_STATE = 1 << 15,
- NL80211_FEATURE_USERSPACE_MPM = 1 << 16,
- NL80211_FEATURE_ACTIVE_MONITOR = 1 << 17,
-+ NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE = 1 << 18,
-+ NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES = 1 << 19,
-+ NL80211_FEATURE_WFA_TPC_IE_IN_PROBES = 1 << 20,
-+ NL80211_FEATURE_QUIET = 1 << 21,
-+ NL80211_FEATURE_TX_POWER_INSERTION = 1 << 22,
-+ NL80211_FEATURE_ACKTO_ESTIMATION = 1 << 23,
-+ NL80211_FEATURE_STATIC_SMPS = 1 << 24,
-+ NL80211_FEATURE_DYNAMIC_SMPS = 1 << 25,
- };
-
- /**
-@@ -3987,6 +4149,25 @@ enum nl80211_acl_policy {
- };
-
- /**
-+ * enum nl80211_smps_mode - SMPS mode
-+ *
-+ * Requested SMPS mode (for AP mode)
-+ *
-+ * @NL80211_SMPS_OFF: SMPS off (use all antennas).
-+ * @NL80211_SMPS_STATIC: static SMPS (use a single antenna)
-+ * @NL80211_SMPS_DYNAMIC: dynamic smps (start with a single antenna and
-+ * turn on other antennas after CTS/RTS).
-+ */
-+enum nl80211_smps_mode {
-+ NL80211_SMPS_OFF,
-+ NL80211_SMPS_STATIC,
-+ NL80211_SMPS_DYNAMIC,
-+
-+ __NL80211_SMPS_AFTER_LAST,
-+ NL80211_SMPS_MAX = __NL80211_SMPS_AFTER_LAST - 1
-+};
-+
-+/**
- * enum nl80211_radar_event - type of radar event for DFS operation
- *
- * Type of event to be used with NL80211_ATTR_RADAR_EVENT to inform userspace
projects / openwrt / staging / dedeckeh.git / blobdiff