CPU_TYPE:=cortex-a9
SUBTARGETS:=generic
-KERNEL_PATCHVER:=4.14
-KERNEL_TESTING_PATCHVER := 4.19
+KERNEL_PATCHVER:=4.19
+KERNEL_TESTING_PATCHVER:=5.4
define Target/Description
Build firmware images for Broadcom based BCM47xx/53xx routers with ARM CPU, *not* MIPS.
--- /dev/null
+CONFIG_64BIT_TIME=y
+# CONFIG_ADIN_PHY is not set
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_AL_FIC is not set
+CONFIG_ARCH_32BIT_OFF_T=y
+CONFIG_ARCH_BCM=y
+CONFIG_ARCH_BCM_5301X=y
+CONFIG_ARCH_BCM_53573=y
+# CONFIG_ARCH_BCM_HR2 is not set
+CONFIG_ARCH_BCM_IPROC=y
+CONFIG_ARCH_CLOCKSOURCE_DATA=y
+CONFIG_ARCH_HAS_BINFMT_FLAT=y
+CONFIG_ARCH_HAS_DEBUG_VIRTUAL=y
+CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
+CONFIG_ARCH_HAS_FORTIFY_SOURCE=y
+CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
+CONFIG_ARCH_HAS_KCOV=y
+CONFIG_ARCH_HAS_KEEPINITRD=y
+CONFIG_ARCH_HAS_MEMBARRIER_SYNC_CORE=y
+CONFIG_ARCH_HAS_PHYS_TO_DMA=y
+CONFIG_ARCH_HAS_SETUP_DMA_OPS=y
+CONFIG_ARCH_HAS_SET_MEMORY=y
+CONFIG_ARCH_HAS_STRICT_KERNEL_RWX=y
+CONFIG_ARCH_HAS_STRICT_MODULE_RWX=y
+CONFIG_ARCH_HAS_TEARDOWN_DMA_OPS=y
+CONFIG_ARCH_HAS_TICK_BROADCAST=y
+CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_KEEP_MEMBLOCK=y
+CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
+# CONFIG_ARCH_MILBEAUT is not set
+CONFIG_ARCH_MULTIPLATFORM=y
+CONFIG_ARCH_MULTI_V6_V7=y
+CONFIG_ARCH_MULTI_V7=y
+CONFIG_ARCH_NR_GPIO=0
+CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y
+CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT=y
+# CONFIG_ARCH_RDA is not set
+CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
+CONFIG_ARCH_SUPPORTS_UPROBES=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARCH_USE_BUILTIN_BSWAP=y
+CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
+CONFIG_ARCH_WANT_DEFAULT_TOPDOWN_MMAP_LAYOUT=y
+CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
+CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
+CONFIG_ARM=y
+CONFIG_ARM_AMBA=y
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_ARM_ARCH_TIMER=y
+CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y
+# CONFIG_ARM_ATAG_DTB_COMPAT is not set
+CONFIG_ARM_ERRATA_754322=y
+CONFIG_ARM_ERRATA_764369=y
+CONFIG_ARM_ERRATA_775420=y
+# CONFIG_ARM_ERRATA_814220 is not set
+# CONFIG_ARM_ERRATA_857271 is not set
+# CONFIG_ARM_ERRATA_857272 is not set
+CONFIG_ARM_GIC=y
+CONFIG_ARM_GLOBAL_TIMER=y
+CONFIG_ARM_HAS_SG_CHAIN=y
+CONFIG_ARM_HEAVY_MB=y
+CONFIG_ARM_L1_CACHE_SHIFT=6
+CONFIG_ARM_L1_CACHE_SHIFT_6=y
+# CONFIG_ARM_LPAE is not set
+CONFIG_ARM_PATCH_IDIV=y
+CONFIG_ARM_PATCH_PHYS_VIRT=y
+# CONFIG_ARM_SP805_WATCHDOG is not set
+CONFIG_ARM_THUMB=y
+# CONFIG_ARM_THUMBEE is not set
+CONFIG_ARM_UNWIND=y
+CONFIG_ARM_VIRT_EXT=y
+CONFIG_ATAGS=y
+CONFIG_AUTO_ZRELADDR=y
+# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
+CONFIG_BCM47XX_NVRAM=y
+CONFIG_BCM47XX_SPROM=y
+CONFIG_BCM47XX_WDT=y
+CONFIG_BCMA=y
+CONFIG_BCMA_BLOCKIO=y
+CONFIG_BCMA_DEBUG=y
+CONFIG_BCMA_DRIVER_GMAC_CMN=y
+CONFIG_BCMA_DRIVER_GPIO=y
+CONFIG_BCMA_DRIVER_PCI=y
+CONFIG_BCMA_HOST_PCI=y
+CONFIG_BCMA_HOST_PCI_POSSIBLE=y
+CONFIG_BCMA_HOST_SOC=y
+CONFIG_BCMA_SFLASH=y
+# CONFIG_BCM_CYGNUS_PHY is not set
+CONFIG_BCM_NET_PHYLIB=y
+CONFIG_BCM_NS_THERMAL=y
+CONFIG_BCM_SR_THERMAL=y
+CONFIG_BGMAC=y
+CONFIG_BGMAC_BCMA=y
+# CONFIG_BGMAC_PLATFORM is not set
+CONFIG_BINFMT_FLAT_ARGVP_ENVP_ON_STACK=y
+CONFIG_BLK_MQ_PCI=y
+CONFIG_BOUNCE=y
+CONFIG_BROADCOM_PHY=y
+CONFIG_CACHE_L2X0=y
+CONFIG_CC_CAN_LINK=y
+CONFIG_CC_HAS_ASM_INLINE=y
+CONFIG_CC_HAS_KASAN_GENERIC=y
+CONFIG_CC_HAS_WARN_MAYBE_UNINITIALIZED=y
+CONFIG_CLKDEV_LOOKUP=y
+CONFIG_CLKSRC_ARM_GLOBAL_TIMER_SCHED_CLOCK=y
+CONFIG_CLKSRC_MMIO=y
+# CONFIG_CLK_BCM_NS2 is not set
+CONFIG_CLK_BCM_NSP=y
+# CONFIG_CLK_BCM_SR is not set
+CONFIG_CLONE_BACKWARDS=y
+CONFIG_COMMON_CLK=y
+# CONFIG_COMMON_CLK_FIXED_MMIO is not set
+CONFIG_COMMON_CLK_IPROC=y
+CONFIG_COMPAT_32BIT_TIME=y
+# CONFIG_COUNTER is not set
+CONFIG_CPU_32v6K=y
+CONFIG_CPU_32v7=y
+CONFIG_CPU_ABRT_EV7=y
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+CONFIG_CPU_CACHE_V7=y
+CONFIG_CPU_CACHE_VIPT=y
+CONFIG_CPU_COPY_V6=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+CONFIG_CPU_HAS_ASID=y
+# CONFIG_CPU_ICACHE_DISABLE is not set
+# CONFIG_CPU_ICACHE_MISMATCH_WORKAROUND is not set
+CONFIG_CPU_PABRT_V7=y
+CONFIG_CPU_RMAP=y
+CONFIG_CPU_SPECTRE=y
+CONFIG_CPU_THUMB_CAPABLE=y
+CONFIG_CPU_TLB_V7=y
+CONFIG_CPU_V7=y
+CONFIG_CRC16=y
+CONFIG_CRYPTO_ACOMP2=y
+# CONFIG_CRYPTO_ADIANTUM is not set
+CONFIG_CRYPTO_AEAD=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_AKCIPHER2=y
+CONFIG_CRYPTO_DEFLATE=y
+# CONFIG_CRYPTO_ECRDSA is not set
+# CONFIG_CRYPTO_ESSIV is not set
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_HASH_INFO=y
+CONFIG_CRYPTO_KPP2=y
+CONFIG_CRYPTO_LIB_AES=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+CONFIG_CRYPTO_NULL2=y
+# CONFIG_CRYPTO_OFB is not set
+CONFIG_CRYPTO_RNG2=y
+# CONFIG_CRYPTO_STREEBOG is not set
+# CONFIG_CRYPTO_XXHASH is not set
+CONFIG_CRYPTO_ZSTD=y
+CONFIG_DCACHE_WORD_ACCESS=y
+CONFIG_DEBUG_BCM_5301X=y
+CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_LL=y
+CONFIG_DEBUG_LL_INCLUDE="debug/8250.S"
+CONFIG_DEBUG_MISC=y
+# CONFIG_DEBUG_PLIST is not set
+CONFIG_DEBUG_UART_8250=y
+# CONFIG_DEBUG_UART_8250_FLOW_CONTROL is not set
+CONFIG_DEBUG_UART_8250_SHIFT=0
+CONFIG_DEBUG_UART_PHYS=0x18000300
+CONFIG_DEBUG_UART_VIRT=0xf1000300
+CONFIG_DEBUG_UNCOMPRESS=y
+CONFIG_DEBUG_USER=y
+CONFIG_DMA_DECLARE_COHERENT=y
+CONFIG_DMA_REMAP=y
+CONFIG_DTC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_EDAC_ATOMIC_SCRUB=y
+CONFIG_EDAC_SUPPORT=y
+# CONFIG_EXFAT_FS is not set
+CONFIG_EXTCON=y
+# CONFIG_FIELDBUS_DEV is not set
+CONFIG_FIXED_PHY=y
+CONFIG_FIX_EARLYCON_MEM=y
+# CONFIG_FS_VERITY is not set
+# CONFIG_FW_LOADER_COMPRESS is not set
+CONFIG_FW_LOADER_PAGED_BUF=y
+# CONFIG_FW_LOADER_USER_HELPER_FALLBACK is not set
+CONFIG_GENERIC_ALLOCATOR=y
+CONFIG_GENERIC_ARCH_TOPOLOGY=y
+CONFIG_GENERIC_BUG=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
+CONFIG_GENERIC_CPU_AUTOPROBE=y
+CONFIG_GENERIC_EARLY_IOREMAP=y
+CONFIG_GENERIC_IDLE_POLL_SETUP=y
+CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y
+CONFIG_GENERIC_IRQ_MULTI_HANDLER=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_PHY=y
+CONFIG_GENERIC_PINCONF=y
+CONFIG_GENERIC_PINCTRL_GROUPS=y
+CONFIG_GENERIC_PINMUX_FUNCTIONS=y
+CONFIG_GENERIC_SCHED_CLOCK=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+CONFIG_GENERIC_STRNCPY_FROM_USER=y
+CONFIG_GENERIC_STRNLEN_USER=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIOLIB_IRQCHIP=y
+CONFIG_GPIO_74X164=y
+# CONFIG_GPIO_AMD_FCH is not set
+# CONFIG_GPIO_CADENCE is not set
+# CONFIG_GPIO_SAMA5D2_PIOBU is not set
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HABANA_AI is not set
+CONFIG_HANDLE_DOMAIN_IRQ=y
+CONFIG_HARDEN_BRANCH_PREDICTOR=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT_MAP=y
+CONFIG_HAVE_ARCH_AUDITSYSCALL=y
+CONFIG_HAVE_ARCH_BITREVERSE=y
+CONFIG_HAVE_ARCH_JUMP_LABEL=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_ARCH_PFN_VALID=y
+CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
+CONFIG_HAVE_ARCH_THREAD_STRUCT_WHITELIST=y
+CONFIG_HAVE_ARCH_TRACEHOOK=y
+CONFIG_HAVE_ARM_ARCH_TIMER=y
+CONFIG_HAVE_ARM_SCU=y
+CONFIG_HAVE_ARM_SMCCC=y
+CONFIG_HAVE_ARM_TWD=y
+CONFIG_HAVE_CLK=y
+CONFIG_HAVE_CLK_PREPARE=y
+CONFIG_HAVE_CONTEXT_TRACKING=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_HAVE_DEBUG_KMEMLEAK=y
+CONFIG_HAVE_DMA_CONTIGUOUS=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_DYNAMIC_FTRACE_WITH_REGS=y
+CONFIG_HAVE_EBPF_JIT=y
+CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
+CONFIG_HAVE_LD_DEAD_CODE_DATA_ELIMINATION=y
+CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
+CONFIG_HAVE_NET_DSA=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_OPTPROBES=y
+CONFIG_HAVE_PCI=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_HAVE_PERF_REGS=y
+CONFIG_HAVE_PERF_USER_STACK_DUMP=y
+CONFIG_HAVE_PROC_CPU=y
+CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
+CONFIG_HAVE_RSEQ=y
+CONFIG_HAVE_SMP=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
+CONFIG_HAVE_UID16=y
+CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
+# CONFIG_HEADERS_INSTALL is not set
+# CONFIG_HEADER_TEST is not set
+CONFIG_HIGHMEM=y
+# CONFIG_HIGHPTE is not set
+CONFIG_HZ_FIXED=0
+CONFIG_HZ_PERIODIC=y
+# CONFIG_I3C is not set
+# CONFIG_IGC is not set
+# CONFIG_IKHEADERS is not set
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_INIT_ON_ALLOC_DEFAULT_ON is not set
+# CONFIG_INIT_ON_FREE_DEFAULT_ON is not set
+CONFIG_INIT_STACK_NONE=y
+# CONFIG_INTERCONNECT is not set
+CONFIG_IO_URING=y
+CONFIG_IRQCHIP=y
+CONFIG_IRQ_DOMAIN=y
+CONFIG_IRQ_DOMAIN_HIERARCHY=y
+CONFIG_IRQ_FORCED_THREADING=y
+CONFIG_IRQ_WORK=y
+CONFIG_KASAN_STACK=1
+# CONFIG_LCD_CLASS_DEVICE is not set
+# CONFIG_LEDS_TRIGGER_AUDIO is not set
+# CONFIG_LEDS_TRIGGER_PATTERN is not set
+CONFIG_LIBFDT=y
+CONFIG_LOCK_DEBUGGING_SUPPORT=y
+# CONFIG_LOCK_EVENT_COUNTS is not set
+CONFIG_LOCK_SPIN_ON_OWNER=y
+CONFIG_LSM="lockdown,yama,loadpin,safesetid,integrity"
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_MDIO_BCM_IPROC=y
+CONFIG_MDIO_BUS=y
+CONFIG_MDIO_BUS_MUX=y
+# CONFIG_MDIO_BUS_MUX_BCM_IPROC is not set
+CONFIG_MDIO_BUS_MUX_MMIOREG=y
+# CONFIG_MDIO_BUS_MUX_MULTIPLEXER is not set
+CONFIG_MDIO_DEVICE=y
+CONFIG_MEMFD_CREATE=y
+CONFIG_MFD_SYSCON=y
+# CONFIG_MFD_TQMX86 is not set
+CONFIG_MIGHT_HAVE_CACHE_L2X0=y
+CONFIG_MIGRATION=y
+# CONFIG_MISC_ALCOR_PCI is not set
+CONFIG_MODULES_USE_ELF_REL=y
+# CONFIG_MODULE_ALLOW_MISSING_NAMESPACE_IMPORTS is not set
+CONFIG_MTD_BCM47XXSFLASH=y
+CONFIG_MTD_BCM47XX_PARTS=y
+# CONFIG_MTD_HYPERBUS is not set
+CONFIG_MTD_PARSER_TRX=y
+# CONFIG_MTD_RAW_NAND is not set
+CONFIG_MTD_SPI_NOR=y
+CONFIG_MTD_SPLIT_SEAMA_FW=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_BEB_LIMIT=20
+CONFIG_MTD_UBI_BLOCK=y
+# CONFIG_MTD_UBI_FASTMAP is not set
+# CONFIG_MTD_UBI_GLUEBI is not set
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MUTEX_SPIN_ON_OWNER=y
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NET_FLOW_LIMIT=y
+# CONFIG_NET_SCH_TAPRIO is not set
+CONFIG_NET_VENDOR_GOOGLE=y
+CONFIG_NET_VENDOR_PENSANDO=y
+# CONFIG_NI_XGE_MANAGEMENT_ENET is not set
+CONFIG_NR_CPUS=2
+# CONFIG_NULL_TTY is not set
+CONFIG_NVMEM=y
+CONFIG_NVMEM_SYSFS=y
+CONFIG_OF=y
+CONFIG_OF_ADDRESS=y
+CONFIG_OF_EARLY_FLATTREE=y
+CONFIG_OF_FLATTREE=y
+CONFIG_OF_GPIO=y
+CONFIG_OF_IRQ=y
+CONFIG_OF_KOBJ=y
+CONFIG_OF_MDIO=y
+CONFIG_OF_NET=y
+CONFIG_OF_RESERVED_MEM=y
+CONFIG_OLD_SIGACTION=y
+CONFIG_OLD_SIGSUSPEND3=y
+CONFIG_OUTER_CACHE=y
+CONFIG_OUTER_CACHE_SYNC=y
+# CONFIG_PACKING is not set
+CONFIG_PADATA=y
+CONFIG_PAGE_OFFSET=0xC0000000
+CONFIG_PCI=y
+CONFIG_PCIE_IPROC=y
+CONFIG_PCIE_IPROC_BCMA=y
+# CONFIG_PCIE_IPROC_PLATFORM is not set
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_DOMAINS_GENERIC=y
+# CONFIG_PCI_V3_SEMI is not set
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PGTABLE_LEVELS=2
+CONFIG_PHYLIB=y
+# CONFIG_PHY_BCM_NS_USB2 is not set
+# CONFIG_PHY_BCM_NS_USB3 is not set
+# CONFIG_PHY_BCM_SR_PCIE is not set
+CONFIG_PHY_BCM_SR_USB=y
+# CONFIG_PHY_BRCM_SATA is not set
+# CONFIG_PHY_CADENCE_DP is not set
+# CONFIG_PHY_CADENCE_DPHY is not set
+# CONFIG_PHY_FSL_IMX8MQ_USB is not set
+# CONFIG_PHY_MIXEL_MIPI_DPHY is not set
+# CONFIG_PHY_NS2_USB_DRD is not set
+# CONFIG_PHY_OCELOT_SERDES is not set
+CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_IPROC_GPIO is not set
+CONFIG_PINCTRL_NS=y
+# CONFIG_PINCTRL_NS2_MUX is not set
+# CONFIG_PINCTRL_OCELOT is not set
+# CONFIG_PL310_ERRATA_588369 is not set
+# CONFIG_PL310_ERRATA_727915 is not set
+# CONFIG_PL310_ERRATA_753970 is not set
+# CONFIG_PL310_ERRATA_769419 is not set
+# CONFIG_PRINTK_CALLER is not set
+# CONFIG_PSI is not set
+# CONFIG_PVPANIC is not set
+# CONFIG_RANDOM_TRUST_BOOTLOADER is not set
+CONFIG_RATIONAL=y
+CONFIG_RCU_NEED_SEGCBLIST=y
+CONFIG_RCU_STALL_COMMON=y
+# CONFIG_REED_SOLOMON_TEST is not set
+CONFIG_REFCOUNT_FULL=y
+CONFIG_REGMAP=y
+CONFIG_REGMAP_MMIO=y
+CONFIG_RFS_ACCEL=y
+CONFIG_RPS=y
+CONFIG_RWSEM_SPIN_ON_OWNER=y
+CONFIG_SERIAL_8250_FSL=y
+# CONFIG_SERIAL_AMBA_PL011 is not set
+# CONFIG_SERIAL_FSL_LINFLEXUART is not set
+CONFIG_SERIAL_MCTRL_GPIO=y
+CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_SERIAL_SIFIVE is not set
+CONFIG_SGL_ALLOC=y
+# CONFIG_SHUFFLE_PAGE_ALLOCATOR is not set
+CONFIG_SMP=y
+CONFIG_SMP_ON_UP=y
+CONFIG_SPARSE_IRQ=y
+CONFIG_SPI=y
+CONFIG_SPI_BCM_QSPI=y
+CONFIG_SPI_BITBANG=y
+CONFIG_SPI_GPIO=y
+CONFIG_SPI_MASTER=y
+CONFIG_SPI_MEM=y
+# CONFIG_SPI_MTK_QUADSPI is not set
+CONFIG_SRCU=y
+CONFIG_SWCONFIG=y
+CONFIG_SWCONFIG_B53=y
+# CONFIG_SWCONFIG_B53_MMAP_DRIVER is not set
+CONFIG_SWCONFIG_B53_PHY_DRIVER=y
+CONFIG_SWCONFIG_B53_PHY_FIXUP=y
+CONFIG_SWCONFIG_B53_SRAB_DRIVER=y
+CONFIG_SWPHY=y
+CONFIG_SWP_EMULATE=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+# CONFIG_TEST_BLACKHOLE_DEV is not set
+# CONFIG_TEST_MEMCAT_P is not set
+# CONFIG_TEST_MEMINIT is not set
+# CONFIG_TEST_STACKINIT is not set
+# CONFIG_TEST_STRSCPY is not set
+# CONFIG_TEST_VMALLOC is not set
+# CONFIG_TEST_XARRAY is not set
+CONFIG_THERMAL=y
+CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
+CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
+CONFIG_THERMAL_GOV_STEP_WISE=y
+CONFIG_THERMAL_OF=y
+# CONFIG_THUMB2_KERNEL is not set
+CONFIG_TICK_CPU_ACCOUNTING=y
+CONFIG_TIMER_OF=y
+CONFIG_TIMER_PROBE=y
+# CONFIG_TI_CPSW_PHY_SEL is not set
+CONFIG_TREE_RCU=y
+CONFIG_TREE_SRCU=y
+# CONFIG_TRUSTED_FOUNDATIONS is not set
+CONFIG_UBIFS_FS=y
+# CONFIG_UBIFS_FS_ADVANCED_COMPR is not set
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_ZLIB=y
+CONFIG_UBIFS_FS_ZSTD=y
+CONFIG_UBSAN_ALIGNMENT=y
+CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
+# CONFIG_UNICODE is not set
+CONFIG_UNIX_SCM=y
+CONFIG_UNWINDER_ARM=y
+# CONFIG_UNWINDER_FRAME_POINTER is not set
+# CONFIG_USB_CONN_GPIO is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USE_OF=y
+# CONFIG_VALIDATE_FS_PARSER is not set
+# CONFIG_VFP is not set
+CONFIG_WATCHDOG_CORE=y
+CONFIG_WATCHDOG_OPEN_TIMEOUT=0
+# CONFIG_XILINX_SDFEC is not set
+CONFIG_XPS=y
+CONFIG_XXHASH=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_BCJ=y
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZSTD_COMPRESS=y
+CONFIG_ZSTD_DECOMPRESS=y
IMAGE/bin := append-rootfs | bcm53xx-tplink-safeloader
TPLINK_BOARD := ARCHER-C5-V2
endef
-TARGET_DEVICES += tplink-archer-c5-v2
+#TARGET_DEVICES += tplink-archer-c5-v2
define Device/tplink-archer-c9-v1
DEVICE_VENDOR := TP-LINK
IMAGE/bin := append-rootfs | bcm53xx-tplink-safeloader
TPLINK_BOARD := ARCHERC9
endef
-TARGET_DEVICES += tplink-archer-c9-v1
+#TARGET_DEVICES += tplink-archer-c9-v1
$(eval $(call BuildImage))
--- /dev/null
+From: Dan Haab <dan.haab@legrand.com>
+Date: Wed, 2 Oct 2019 09:57:26 -0600
+Subject: [PATCH] ARM: dts: BCM5301X: Add DT for Luxul XWC-2000
+
+It's a simple network device based on BCM47094 with just a single
+Ethernet port.
+
+Signed-off-by: Dan Haab <dan.haab@legrand.com>
+---
+ arch/arm/boot/dts/Makefile | 1 +
+ arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts | 53 +++++++++++++++++++
+ 2 files changed, 54 insertions(+)
+ create mode 100644 arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -111,6 +111,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
+ bcm47094-luxul-abr-4500.dtb \
+ bcm47094-luxul-xap-1610.dtb \
+ bcm47094-luxul-xbr-4500.dtb \
++ bcm47094-luxul-xwc-2000.dtb \
+ bcm47094-luxul-xwr-3100.dtb \
+ bcm47094-luxul-xwr-3150-v1.dtb \
+ bcm47094-netgear-r8500.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts
+@@ -0,0 +1,53 @@
++// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
++/*
++ * Copyright 2019 Legrand AV Inc.
++ */
++
++/dts-v1/;
++
++#include "bcm47094.dtsi"
++#include "bcm5301x-nand-cs0-bch8.dtsi"
++
++/ {
++ compatible = "luxul,xwc-2000-v1", "brcm,bcm47094", "brcm,bcm4708";
++ model = "Luxul XWC-2000 V1";
++
++ chosen {
++ bootargs = "earlycon";
++ };
++
++ memory {
++ reg = <0x00000000 0x08000000
++ 0x88000000 0x18000000>;
++ };
++
++ leds {
++ compatible = "gpio-leds";
++
++ status {
++ label = "bcm53xx:green:status";
++ gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "timer";
++ };
++ };
++
++ gpio-keys {
++ compatible = "gpio-keys";
++ #address-cells = <1>;
++ #size-cells = <0>;
++
++ restart {
++ label = "Reset";
++ linux,code = <KEY_RESTART>;
++ gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
++ };
++ };
++};
++
++&uart1 {
++ status = "okay";
++};
++
++&spi_nor {
++ status = "okay";
++};
--- /dev/null
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
+Date: Sat, 1 Oct 2016 22:54:48 +0200
+Subject: [PATCH] usb: xhci: add support for performing fake doorbell
+
+Broadcom's Northstar XHCI controllers seem to need a special start
+procedure to work correctly. There isn't any official documentation of
+this, the problem is that controller doesn't detect any connected
+devices with default setup. Moreover connecting USB device to controller
+that doesn't run properly can cause SoC's watchdog issues.
+
+A workaround that was successfully tested on multiple devices is to
+perform a fake doorbell. This patch adds code for doing this and enables
+it on BCM4708 family.
+---
+ drivers/usb/host/xhci-plat.c | 6 +++++
+ drivers/usb/host/xhci.c | 63 +++++++++++++++++++++++++++++++++++++++++---
+ drivers/usb/host/xhci.h | 1 +
+ 3 files changed, 67 insertions(+), 3 deletions(-)
+
+Index: linux-5.4.11/drivers/usb/host/xhci-plat.c
+===================================================================
+--- linux-5.4.11.orig/drivers/usb/host/xhci-plat.c
++++ linux-5.4.11/drivers/usb/host/xhci-plat.c
+@@ -67,6 +67,8 @@ static int xhci_priv_resume_quirk(struct
+ static void xhci_plat_quirks(struct device *dev, struct xhci_hcd *xhci)
+ {
+ struct xhci_plat_priv *priv = xhci_to_priv(xhci);
++ struct platform_device*pdev = to_platform_device(dev);
++ struct device_node *node = pdev->dev.of_node;
+
+ /*
+ * As of now platform drivers don't provide MSI support so we ensure
+@@ -74,6 +76,9 @@ static void xhci_plat_quirks(struct devi
+ * dev struct in order to setup MSI
+ */
+ xhci->quirks |= XHCI_PLAT | priv->quirks;
++
++ if (node && of_machine_is_compatible("brcm,bcm4708"))
++ xhci->quirks |= XHCI_FAKE_DOORBELL;
+ }
+
+ /* called during probe() after chip reset completes */
+Index: linux-5.4.11/drivers/usb/host/xhci.c
+===================================================================
+--- linux-5.4.11.orig/drivers/usb/host/xhci.c
++++ linux-5.4.11/drivers/usb/host/xhci.c
+@@ -156,6 +156,49 @@ int xhci_start(struct xhci_hcd *xhci)
+ return ret;
+ }
+
++/**
++ * xhci_fake_doorbell - Perform a fake doorbell on a specified slot
++ *
++ * Some controllers require a fake doorbell to start correctly. Without that
++ * they simply don't detect any devices.
++ */
++static int xhci_fake_doorbell(struct xhci_hcd *xhci, int slot_id)
++{
++ u32 temp;
++
++ /* Alloc a virt device for that slot */
++ if (!xhci_alloc_virt_device(xhci, slot_id, NULL, GFP_NOIO)) {
++ xhci_warn(xhci, "Could not allocate xHCI USB device data structures\n");
++ return -ENOMEM;
++ }
++
++ /* Ring fake doorbell for slot_id ep 0 */
++ xhci_ring_ep_doorbell(xhci, slot_id, 0, 0);
++ usleep_range(1000, 1500);
++
++ /* Read the status to check if HSE is set or not */
++ temp = readl(&xhci->op_regs->status);
++
++ /* Clear HSE if set */
++ if (temp & STS_FATAL) {
++ xhci_dbg(xhci, "HSE problem detected, status: 0x%08x\n", temp);
++ temp &= ~0x1fff;
++ temp |= STS_FATAL;
++ writel(temp, &xhci->op_regs->status);
++ usleep_range(1000, 1500);
++ readl(&xhci->op_regs->status);
++ }
++
++ /* Free virt device */
++ xhci_free_virt_device(xhci, slot_id);
++
++ /* We're done if controller is already running */
++ if (readl(&xhci->op_regs->command) & CMD_RUN)
++ return 0;
++
++ return xhci_start(xhci);
++}
++
+ /*
+ * Reset a halted HC.
+ *
+@@ -604,10 +647,20 @@ static int xhci_init(struct usb_hcd *hcd
+
+ static int xhci_run_finished(struct xhci_hcd *xhci)
+ {
+- if (xhci_start(xhci)) {
+- xhci_halt(xhci);
+- return -ENODEV;
++ int err;
++
++ err = xhci_start(xhci);
++ if (err) {
++ err = -ENODEV;
++ goto err_halt;
+ }
++
++ if (xhci->quirks & XHCI_FAKE_DOORBELL) {
++ err = xhci_fake_doorbell(xhci, 1);
++ if (err)
++ goto err_halt;
++ }
++
+ xhci->shared_hcd->state = HC_STATE_RUNNING;
+ xhci->cmd_ring_state = CMD_RING_STATE_RUNNING;
+
+@@ -617,6 +670,10 @@ static int xhci_run_finished(struct xhci
+ xhci_dbg_trace(xhci, trace_xhci_dbg_init,
+ "Finished xhci_run for USB3 roothub");
+ return 0;
++
++err_halt:
++ xhci_halt(xhci);
++ return err;
+ }
+
+ /*
+Index: linux-5.4.11/drivers/usb/host/xhci.h
+===================================================================
+--- linux-5.4.11.orig/drivers/usb/host/xhci.h
++++ linux-5.4.11/drivers/usb/host/xhci.h
+@@ -1867,6 +1867,7 @@ struct xhci_hcd {
+ #define XHCI_DEFAULT_PM_RUNTIME_ALLOW BIT_ULL(33)
+ #define XHCI_RESET_PLL_ON_DISCONNECT BIT_ULL(34)
+ #define XHCI_SNPS_BROKEN_SUSPEND BIT_ULL(35)
++#define XHCI_FAKE_DOORBELL BIT_ULL(36)
+
+ unsigned int num_active_eps;
+ unsigned int limit_active_eps;
--- /dev/null
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
+Date: Wed, 24 Sep 2014 22:14:07 +0200
+Subject: [PATCH] ARM: BCM5301X: Disable MMU and Dcache during decompression
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Broadcom devices have broken CFE (bootloader) that leaves hardware in an
+invalid state. It causes problems with booting Linux. On Northstar
+devices kernel was randomly hanging in ~25% of tries during early init.
+Hangs used to happen at random places in the start_kernel. On BCM53573
+kernel doesn't even seem to start booting.
+
+To workaround this problem we need to do following very early:
+1) Clear 2 following bits in the SCTLR register:
+#define CR_M (1 << 0) /* MMU enable */
+#define CR_C (1 << 2) /* Dcache enable */
+2) Flush the whole D-cache
+3) Disable L2 cache
+
+Unfortunately this patch is not upstreamable as it does above things
+unconditionally. We can't check if we are running on Broadcom platform
+in any safe way and doing such hacks with ARCH_MULTI_V7 is unacceptable
+as it could break other devices support.
+
+Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
+---
+
+--- a/arch/arm/boot/compressed/Makefile
++++ b/arch/arm/boot/compressed/Makefile
+@@ -35,6 +35,11 @@ ifeq ($(CONFIG_ARCH_ACORN),y)
+ OBJS += ll_char_wr.o font.o
+ endif
+
++ifeq ($(CONFIG_ARCH_BCM_5301X),y)
++OBJS += head-bcm_5301x-mpcore.o
++OBJS += cache-v7-min.o
++endif
++
+ ifeq ($(CONFIG_ARCH_SA1100),y)
+ OBJS += head-sa1100.o
+ endif
+--- /dev/null
++++ b/arch/arm/boot/compressed/head-bcm_5301x-mpcore.S
+@@ -0,0 +1,37 @@
++/*
++ *
++ * Platform specific tweaks. This is merged into head.S by the linker.
++ *
++ */
++
++#include <linux/linkage.h>
++#include <asm/assembler.h>
++#include <asm/cp15.h>
++
++ .section ".start", "ax"
++
++/*
++ * This code section is spliced into the head code by the linker
++ */
++
++__plat_uncompress_start:
++
++ @ Preserve r8/r7 i.e. kernel entry values
++ mov r12, r8
++
++ @ Clear MMU enable and Dcache enable bits
++ mrc p15, 0, r0, c1, c0, 0 @ Read SCTLR
++ bic r0, #CR_C|CR_M
++ mcr p15, 0, r0, c1, c0, 0 @ Write SCTLR
++ nop
++
++ @ Call the cache invalidation routine
++ bl v7_flush_dcache_all
++ nop
++ mov r0,#0
++ ldr r3, =0x19022000 @ L2 cache controller, control reg
++ str r0, [r3, #0x100] @ Disable L2 cache
++ nop
++
++ @ Restore
++ mov r8, r12
+--- a/arch/arm/boot/compressed/cache-v7-min.S
++++ b/arch/arm/boot/compressed/cache-v7-min.S
+@@ -12,6 +12,7 @@
+
+ #include <linux/linkage.h>
+ #include <linux/init.h>
++#include <asm/assembler.h>
+
+ __INIT
+
+@@ -63,7 +64,7 @@ loop2:
+ ARM( orr r11, r11, r9, lsl r2 ) @ factor index number into r11
+ THUMB( lsl r6, r9, r2 )
+ THUMB( orr r11, r11, r6 ) @ factor index number into r11
+- mcr p15, 0, r11, c7, c14, 2 @ clean & invalidate by set/way
++ mcr p15, 0, r11, c7, c6, 2 @ clean & invalidate by set/way
+ subs r9, r9, #1 @ decrement the index
+ bge loop2
+ subs r4, r4, #1 @ decrement the way
--- /dev/null
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
+Subject: [PATCH] ARM: dts: BCM5301X: Update Northstar pinctrl binding
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
+---
+
+--- a/arch/arm/boot/dts/bcm5301x.dtsi
++++ b/arch/arm/boot/dts/bcm5301x.dtsi
+@@ -400,16 +400,12 @@
+ #size-cells = <1>;
+
+ cru@100 {
+- compatible = "simple-bus";
++ compatible = "syscon", "simple-mfd";
+ reg = <0x100 0x1a4>;
+- ranges;
+- #address-cells = <1>;
+- #size-cells = <1>;
+
+- pin-controller@1c0 {
++ pinctrl {
+ compatible = "brcm,bcm4708-pinmux";
+- reg = <0x1c0 0x24>;
+- reg-names = "cru_gpio_control";
++ offset = <0xc0>;
+
+ spi-pins {
+ groups = "spi_grp";
--- /dev/null
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <zajec5@gmail.com>
+Subject: [PATCH] ARM: BCM5301X: Add DT for Netgear R7900
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
+---
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -104,6 +104,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
+ bcm4709-buffalo-wxr-1900dhp.dtb \
+ bcm4709-linksys-ea9200.dtb \
+ bcm4709-netgear-r7000.dtb \
++ bcm4709-netgear-r7900.dtb \
+ bcm4709-netgear-r8000.dtb \
+ bcm4709-tplink-archer-c9-v1.dtb \
+ bcm47094-dlink-dir-885l.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/bcm4709-netgear-r7900.dts
+@@ -0,0 +1,42 @@
++/*
++ * Broadcom BCM470X / BCM5301X ARM platform code.
++ * DTS for Netgear R7900
++ *
++ * Copyright (C) 2016 Rafał Miłecki <zajec5@gmail.com>
++ *
++ * Licensed under the GNU/GPL. See COPYING for details.
++ */
++
++/dts-v1/;
++
++#include "bcm4709.dtsi"
++#include "bcm5301x-nand-cs0-bch8.dtsi"
++
++/ {
++ compatible = "netgear,r7900", "brcm,bcm4709", "brcm,bcm4708";
++ model = "Netgear R7900";
++
++ chosen {
++ bootargs = "console=ttyS0,115200";
++ };
++
++ memory {
++ reg = <0x00000000 0x08000000
++ 0x88000000 0x08000000>;
++ };
++
++ axi@18000000 {
++ usb3@23000 {
++ reg = <0x00023000 0x1000>;
++
++ #address-cells = <1>;
++ #size-cells = <1>;
++
++ vcc-gpio = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
++ };
++ };
++};
++
++&uart0 {
++ status = "okay";
++};
--- /dev/null
+From: Felix Fietkau <nbd@nbd.name>
+Subject: [PATCH] ARM: BCM5301X: Add power button for Buffalo WZR-1750DHP
+
+Signed-off-by: Felix Fietkau <nbd@nbd.name>
+---
+--- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
++++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
+@@ -101,6 +101,12 @@
+ #address-cells = <1>;
+ #size-cells = <0>;
+
++ power {
++ label = "Power";
++ linux,code = <KEY_POWER>;
++ gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
++ };
++
+ restart {
+ label = "Reset";
+ linux,code = <KEY_RESTART>;
--- /dev/null
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
+Subject: [PATCH] ARM: dts: BCM5301X: Add serial= to the bootargs
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+It's enough to have proper stdout-path for getting serial working but
+for some reason LEDE doesn't offer "Please press Enter to activate this
+console." unless ttyS0 is specified.
+
+This is a workaround to get serial working in LEDE.
+
+Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
+---
+
+Index: linux-5.4.11/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
+===================================================================
+--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
++++ linux-5.4.11/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
+@@ -12,7 +12,7 @@
+ model = "TP-LINK Archer C5 V2";
+
+ chosen {
+- bootargs = "earlycon";
++ bootargs = "console=ttyS0,115200 earlycon";
+ };
+
+ memory@0 {
+Index: linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
+===================================================================
+--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
++++ linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
+@@ -13,7 +13,7 @@
+ model = "Luxul ABR-4500 V1";
+
+ chosen {
+- bootargs = "earlycon";
++ bootargs = "console=ttyS0,115200 earlycon";
+ };
+
+ memory@0 {
+Index: linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
+===================================================================
+--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
++++ linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
+@@ -13,7 +13,7 @@
+ model = "Luxul XBR-4500 V1";
+
+ chosen {
+- bootargs = "earlycon";
++ bootargs = "console=ttyS0,115200 earlycon";
+ };
+
+ memory@0 {
+Index: linux-5.4.11/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
+===================================================================
+--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
++++ linux-5.4.11/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
+@@ -12,7 +12,7 @@
+ model = "Luxul XAP-1440 V1";
+
+ chosen {
+- bootargs = "earlycon";
++ bootargs = "console=ttyS0,115200 earlycon";
+ };
+
+ memory@0 {
+Index: linux-5.4.11/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
+===================================================================
+--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
++++ linux-5.4.11/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
+@@ -12,7 +12,7 @@
+ model = "Luxul XAP-810 V1";
+
+ chosen {
+- bootargs = "earlycon";
++ bootargs = "console=ttyS0,115200 earlycon";
+ };
+
+ memory@0 {
+Index: linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts
+===================================================================
+--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts
++++ linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts
+@@ -12,7 +12,7 @@
+ model = "Luxul XAP-1610 V1";
+
+ chosen {
+- bootargs = "earlycon";
++ bootargs = "console=ttyS0,115200 earlycon";
+ };
+
+ memory@0 {
+Index: linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts
+===================================================================
+--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts
++++ linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts
+@@ -13,7 +13,7 @@
+ model = "Luxul XWR-3150 V1";
+
+ chosen {
+- bootargs = "earlycon";
++ bootargs = "console=ttyS0,115200 earlycon";
+ };
+
+ memory@0 {
+Index: linux-5.4.11/arch/arm/boot/dts/bcm47094-phicomm-k3.dts
+===================================================================
+--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47094-phicomm-k3.dts
++++ linux-5.4.11/arch/arm/boot/dts/bcm47094-phicomm-k3.dts
+@@ -13,6 +13,10 @@
+ compatible = "phicomm,k3", "brcm,bcm47094", "brcm,bcm4708";
+ model = "Phicomm K3";
+
++ chosen {
++ bootargs = "console=ttyS0,115200";
++ };
++
+ memory@0 {
+ device_type = "memory";
+ reg = <0x00000000 0x08000000
+Index: linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts
+===================================================================
+--- linux-5.4.11.orig/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts
++++ linux-5.4.11/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts
+@@ -13,7 +13,7 @@
+ model = "Luxul XWC-2000 V1";
+
+ chosen {
+- bootargs = "earlycon";
++ bootargs = "console=ttyS0,115200 earlycon";
+ };
+
+ memory {
--- /dev/null
+From 7166207bd1d8c46d09d640d46afc685df9bb9083 Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
+Date: Thu, 22 Nov 2018 09:21:49 +0100
+Subject: [PATCH] ARM: dts: BCM5301X: Describe partition formats
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+It's needed by OpenWrt for custom partitioning.
+
+Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
+---
+ arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts | 1 +
+ 1 file changed, 1 insertion(+)
+
+--- a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
++++ b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
+@@ -34,6 +34,7 @@
+ partition@0 {
+ label = "firmware";
+ reg = <0x00000000 0x08000000>;
++ compatible = "seama";
+ };
+ };
+ };
--- /dev/null
+From 2a2af518266a29323cf30c3f9ba9ef2ceb1dd84b Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <zajec5@gmail.com>
+Date: Thu, 16 Oct 2014 20:52:16 +0200
+Subject: [PATCH] UBI: Detect EOF mark and erase all remaining blocks
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
+---
+ drivers/mtd/ubi/attach.c | 5 +++++
+ drivers/mtd/ubi/io.c | 4 ++++
+ drivers/mtd/ubi/ubi.h | 1 +
+ 3 files changed, 10 insertions(+)
+
+--- a/drivers/mtd/ubi/attach.c
++++ b/drivers/mtd/ubi/attach.c
+@@ -95,6 +95,9 @@ static int self_check_ai(struct ubi_devi
+ #define AV_ADD BIT(1)
+ #define AV_FIND_OR_ADD (AV_FIND | AV_ADD)
+
++/* Set on finding block with 0xdeadc0de, indicates erasing all blocks behind */
++bool erase_all_next;
++
+ /**
+ * find_or_add_av - internal function to find a volume, add a volume or do
+ * both (find and add if missing).
+@@ -1592,6 +1595,8 @@ int ubi_attach(struct ubi_device *ubi, i
+ if (!ai)
+ return -ENOMEM;
+
++ erase_all_next = false;
++
+ #ifdef CONFIG_MTD_UBI_FASTMAP
+ /* On small flash devices we disable fastmap in any case. */
+ if ((int)mtd_div_by_eb(ubi->mtd->size, ubi->mtd) <= UBI_FM_MAX_START) {
+--- a/drivers/mtd/ubi/io.c
++++ b/drivers/mtd/ubi/io.c
+@@ -723,6 +723,10 @@ int ubi_io_read_ec_hdr(struct ubi_device
+ }
+
+ magic = be32_to_cpu(ec_hdr->magic);
++ if (magic == 0xdeadc0de)
++ erase_all_next = true;
++ if (erase_all_next)
++ return read_err ? UBI_IO_FF_BITFLIPS : UBI_IO_FF;
+ if (magic != UBI_EC_HDR_MAGIC) {
+ if (mtd_is_eccerr(read_err))
+ return UBI_IO_BAD_HDR_EBADMSG;
+--- a/drivers/mtd/ubi/ubi.h
++++ b/drivers/mtd/ubi/ubi.h
+@@ -833,6 +833,7 @@ extern struct mutex ubi_devices_mutex;
+ extern struct blocking_notifier_head ubi_notifiers;
+
+ /* attach.c */
++extern bool erase_all_next;
+ struct ubi_ainf_peb *ubi_alloc_aeb(struct ubi_attach_info *ai, int pnum,
+ int ec);
+ void ubi_free_aeb(struct ubi_attach_info *ai, struct ubi_ainf_peb *aeb);
--- /dev/null
+From 4abdde3ad6bc0b3b157c4bf6ec0bf139d11d07e8 Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <zajec5@gmail.com>
+Date: Wed, 13 May 2015 14:13:28 +0200
+Subject: [PATCH] b53: add hacky CPU port fixes for devices not using port 5
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
+---
+ drivers/net/phy/b53/b53_common.c | 6 ++++++
+ 1 file changed, 6 insertions(+)
+
+--- a/drivers/net/phy/b53/b53_common.c
++++ b/drivers/net/phy/b53/b53_common.c
+@@ -28,6 +28,7 @@
+ #include <linux/of.h>
+ #include <linux/of_net.h>
+ #include <linux/platform_data/b53.h>
++#include <linux/of.h>
+
+ #include "b53_regs.h"
+ #include "b53_priv.h"
+@@ -1579,6 +1580,28 @@ static int b53_switch_init(struct b53_de
+ return ret;
+ }
+
++ /* Set correct CPU port */
++ if (of_machine_is_compatible("asus,rt-ac87u"))
++ sw_dev->cpu_port = 7;
++ else if (of_machine_is_compatible("netgear,r7900"))
++ sw_dev->cpu_port = 8;
++ else if (of_machine_is_compatible("netgear,r8000"))
++ sw_dev->cpu_port = 8;
++ else if (of_machine_is_compatible("netgear,r8500"))
++ sw_dev->cpu_port = 8;
++
++ /* Enable extra ports */
++ if (of_machine_is_compatible("tenda,ac9"))
++ dev->enabled_ports |= BIT(5);
++
++ /*
++ * Workaround for devices using port 8 (connected to the 3rd iface).
++ * For some reason it doesn't work (no packets on eth2).
++ */
++ if (of_machine_is_compatible("netgear,r7900") ||
++ of_machine_is_compatible("netgear,r8000"))
++ sw_dev->cpu_port = 5;
++
+ dev->enabled_ports |= BIT(sw_dev->cpu_port);
+ sw_dev->ports = fls(dev->enabled_ports);
+
--- /dev/null
+From 6f1c62440eb6846cb8045d7a5480ec7bbe47c96f Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= <rafal@milecki.pl>
+Date: Mon, 15 Aug 2016 10:30:41 +0200
+Subject: [PATCH] BCM53573 minor hacks
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
+---
+
+--- a/arch/arm/boot/dts/bcm53573.dtsi
++++ b/arch/arm/boot/dts/bcm53573.dtsi
+@@ -53,6 +53,7 @@
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
++ clocks = <&ilp>;
+ };
+
+ clocks {
+--- a/drivers/bcma/main.c
++++ b/drivers/bcma/main.c
+@@ -330,14 +330,6 @@ static int bcma_register_devices(struct
+ }
+ #endif
+
+-#ifdef CONFIG_BCMA_SFLASH
+- if (bus->drv_cc.sflash.present) {
+- err = platform_device_register(&bcma_sflash_dev);
+- if (err)
+- bcma_err(bus, "Error registering serial flash\n");
+- }
+-#endif
+-
+ #ifdef CONFIG_BCMA_NFLASH
+ if (bus->drv_cc.nflash.present) {
+ err = platform_device_register(&bcma_nflash_dev);
+@@ -415,6 +407,14 @@ int bcma_bus_register(struct bcma_bus *b
+ bcma_register_core(bus, core);
+ }
+
++#ifdef CONFIG_BCMA_SFLASH
++ if (bus->drv_cc.sflash.present) {
++ err = platform_device_register(&bcma_sflash_dev);
++ if (err)
++ bcma_err(bus, "Error registering serial flash\n");
++ }
++#endif
++
+ /* Try to get SPROM */
+ err = bcma_sprom_get(bus);
+ if (err == -ENOENT) {
+--- a/drivers/clocksource/arm_arch_timer.c
++++ b/drivers/clocksource/arm_arch_timer.c
+@@ -17,6 +17,7 @@
+ #include <linux/smp.h>
+ #include <linux/cpu.h>
+ #include <linux/cpu_pm.h>
++#include <linux/clk.h>
+ #include <linux/clockchips.h>
+ #include <linux/clocksource.h>
+ #include <linux/interrupt.h>
+@@ -919,6 +920,16 @@ static void arch_timer_of_configure_rate
+ if (of_property_read_u32(np, "clock-frequency", &arch_timer_rate))
+ arch_timer_rate = rate;
+
++ /* Get clk rate through clk driver if present */
++ if (!arch_timer_rate) {
++ struct clk *clk = of_clk_get(np, 0);
++
++ if (!IS_ERR(clk)) {
++ if (!clk_prepare_enable(clk))
++ arch_timer_rate = clk_get_rate(clk);
++ }
++ }
++
+ /* Check the timer frequency. */
+ if (arch_timer_rate == 0)
+ pr_warn("frequency not available\n");
projects / openwrt / staging / dedeckeh.git / commitdiff