ath10k-firmware: update Candela Tech firmware images
authorRobert Marko <robimarko@gmail.com>
Thu, 9 May 2019 15:27:57 +0000 (17:27 +0200)
committerChristian Lamparter <chunkeey@gmail.com>
Sat, 11 May 2019 14:37:11 +0000 (16:37 +0200)
Release notes since last time:

Release notes for wave-1:

2019-04-02: Support some get/set API for eeprom rate power tables.
    Mostly backported from 10.2

2019-04-02: Support adaptive-CCA, backported from 10.2

2019-04-02: Support adding eeprom configAddr pairs via the
            set-special API. These configAddrs can be used to change
            the default register settings for up to 12 registers.

2019-05-03: Fix tx-power settings for 2x2, 3x3 rates.
    Original logic I put in back in 2016 set 2x2 and 3x3 lower
    than the needed to be when using most NICs (very high
    powered NICs would not have been affected I think, not sure
    any of those exist though.)

    This improves throughput for 2x2 and 3x3 devices,
    especially when the signal is weaker.

Release notes for wave-2:

2019-04-08: When setting keys, if high bit of high value of
    key_rsc_counter is set to 0x1, then the lower 48 bits will
    be used as the PN value.  By default, PN is set to 1 each
    time the key is set.

2019-04-08: Pack PN into un-used 'excretries' aka
    'num_pkt_loss_excess_retry' high 16 bits.
    This lets us report peer PN, but *only* if driver has
    previously set a PN when setting key (or set-special cmd is
    used to enable PN reporting).

    This is done so that we know the driver is recent
            enough to deal with the PN stat reporting.

2019-04-16: Support specifying tx rate on a per-beacon packet.
    See ath10k_wmi_op_gen_beacon_dma and
    ath10k_convert_hw_rate_to_rate_info for API details.

     Driver needs additional work to actually enable this
     feature currently.

2019-04-30: Compile out tx-prefetch caching logic.
    It is full of tricky bugs that cause tx hangs.
    I fixed at least one, but more remain and I have wasted too
    much time on this already.

2019-05-08: Start rate-ctrl at mcs-3 instead of mcs-5.
    This significantly helps DHCP happen quickly, probably
    because the initial rate being too high would take a while
    to ramp down, especially since there are few packets sent
    by the time DHCP needs to start.

    This bug was triggered by me decreasing retries of 0x1e
    (upstream default) to 0x4.  But, I think it is better to
    start with lower initial MCS instead of always having a
    very high retry count.

Tested on 8devices Jalapeno dev board(IPQ4019)

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [neatify]
package/firmware/ath10k-firmware/Makefile

index 452e7a3..dca1520 100644 (file)
@@ -64,92 +64,92 @@ define Download/ct-firmware-htt
   URL_FILE:=$($(1)_FIRMWARE_FILE_CT_HTT)
 endef
 
-QCA988X_FIRMWARE_FILE_CT:=firmware-2-ct-full-community-22.bin.lede.007
+QCA988X_FIRMWARE_FILE_CT:=firmware-2-ct-full-community-22.bin.lede.008
 define Download/ath10k-firmware-qca988x-ct
   $(call Download/ct-firmware,QCA988X,)
-  HASH:=56b8faa255d053404981fc0e2ffa8dec1aa6adfffd4e4a2af2b6ac25f131ecce
+  HASH:=c2407cbdaaf143c9796e654aed026f0aa70fc93a82dd1244c62e95ede894e829
 endef
 $(eval $(call Download,ath10k-firmware-qca988x-ct))
 
-QCA988X_FIRMWARE_FILE_CT_HTT:=firmware-2-ct-full-htt-mgt-community-22.bin.lede.007
+QCA988X_FIRMWARE_FILE_CT_HTT:=firmware-2-ct-full-htt-mgt-community-22.bin.lede.008
 define Download/ath10k-firmware-qca988x-ct-htt
   $(call Download/ct-firmware-htt,QCA988X,)
-  HASH:=f85296afae06548256167a58ecf58f11cc79aba7f96629124dc7b07611f4614f
+  HASH:=789c4d1c8ac5edeb43d507157944102b564cd6970c365a14b50cab08ffa4e3b5
 endef
 $(eval $(call Download,ath10k-firmware-qca988x-ct-htt))
 
 
-QCA9887_FIRMWARE_FILE_CT:=firmware-2-ct-full-community-22.bin.lede.007
+QCA9887_FIRMWARE_FILE_CT:=firmware-2-ct-full-community-22.bin.lede.008
 define Download/ath10k-firmware-qca9887-ct
   $(call Download/ct-firmware,QCA9887,ath10k-9887)
-  HASH:=d42d57ded7de4f8caf4bfd163db0910af7f0e155b11e484dbaa94c341f1e6dec
+  HASH:=07692a63ab9d11a65c17cc896aff89ea33b7af4e0e1e51ae100651291afe3a4d
 endef
 $(eval $(call Download,ath10k-firmware-qca9887-ct))
 
-QCA9887_FIRMWARE_FILE_CT_HTT:=firmware-2-ct-full-htt-mgt-community-22.bin.lede.007
+QCA9887_FIRMWARE_FILE_CT_HTT:=firmware-2-ct-full-htt-mgt-community-22.bin.lede.008
 define Download/ath10k-firmware-qca9887-ct-htt
   $(call Download/ct-firmware-htt,QCA9887,ath10k-9887)
-  HASH:=2b016a6f59520925ff9996e458c26dde3422e2d142a36e235cca7aad822ad2b6
+  HASH:=ef336462d4a44ab9a0d89e83064124e647a9fb4a8af8be9df5724378611d2e82
 endef
 $(eval $(call Download,ath10k-firmware-qca9887-ct-htt))
 
 
-QCA99X0_FIRMWARE_FILE_CT:=firmware-5-ct-full-community-12.bin-lede.007
+QCA99X0_FIRMWARE_FILE_CT:=firmware-5-ct-full-community-12.bin-lede.008
 define Download/ath10k-firmware-qca99x0-ct
   $(call Download/ct-firmware,QCA99X0,ath10k-10-4b)
-  HASH:=3dbf966fdbad9e55936fa62516e2fcca2a5952030132407f80c41d7da819c82c
+  HASH:=3357d7ba739512619ccd14043338cfe8e148d5d8e99343e3ccf7a2ff0d07d05f
 endef
 $(eval $(call Download,ath10k-firmware-qca99x0-ct))
 
-QCA99X0_FIRMWARE_FILE_CT_HTT:=firmware-5-ct-full-htt-mgt-community-12.bin-lede.007
+QCA99X0_FIRMWARE_FILE_CT_HTT:=firmware-5-ct-full-htt-mgt-community-12.bin-lede.008
 define Download/ath10k-firmware-qca99x0-ct-htt
   $(call Download/ct-firmware-htt,QCA99X0,ath10k-10-4b)
-  HASH:=c98993f541fbe02e88dfd3d5ed70bbaaad228776da29260348c5b00966682b69
+  HASH:=ce81e1b9b80b30263e9d5010e38fac3f005214fd955dc2cff95e7fe633796212
 endef
 $(eval $(call Download,ath10k-firmware-qca99x0-ct-htt))
 
 
-QCA9984_FIRMWARE_FILE_CT:=firmware-5-ct-full-community-12.bin-lede.007
+QCA9984_FIRMWARE_FILE_CT:=firmware-5-ct-full-community-12.bin-lede.008
 define Download/ath10k-firmware-qca9984-ct
   $(call Download/ct-firmware,QCA9984,ath10k-9984-10-4b)
-  HASH:=1bdb2f62fb7f6947db992f0dc48b2864b51c7544ff8672a6c7570ecf2273054c
+  HASH:=e2794ce577ff7942dc5f767a77fa52167f323bc8f50f04570fc5efe92ed761cf
 endef
 $(eval $(call Download,ath10k-firmware-qca9984-ct))
 
-QCA9984_FIRMWARE_FILE_CT_HTT:=firmware-5-ct-full-htt-mgt-community-12.bin-lede.007
+QCA9984_FIRMWARE_FILE_CT_HTT:=firmware-5-ct-full-htt-mgt-community-12.bin-lede.008
 define Download/ath10k-firmware-qca9984-ct-htt
   $(call Download/ct-firmware-htt,QCA9984,ath10k-9984-10-4b)
-  HASH:=ff4c4f734711d4ead8a8ed226c5347073a9ce32b60b91d995f197b6e7809b7c6
+  HASH:=1f90555963c2e52ac8fc5581b2a0f9c658e3f5205844898bdc48c78d009bb6eb
 endef
 $(eval $(call Download,ath10k-firmware-qca9984-ct-htt))
 
 
-QCA4019_FIRMWARE_FILE_CT:=firmware-5-ct-full-community-12.bin-lede.007
+QCA4019_FIRMWARE_FILE_CT:=firmware-5-ct-full-community-12.bin-lede.008
 define Download/ath10k-firmware-qca4019-ct
   $(call Download/ct-firmware,QCA4019,ath10k-4019-10-4b)
-  HASH:=98568845cf82dea679b1f4dee23f3d3eb39755c6bcdaeb89ed188e52e0f42b2d
+  HASH:=4e73cf8e24e83df87d6dce2038e350b3f67753ccca37a8c0d1b861818991e6aa
 endef
 $(eval $(call Download,ath10k-firmware-qca4019-ct))
 
-QCA4019_FIRMWARE_FILE_CT_HTT:=firmware-5-ct-full-htt-mgt-community-12.bin-lede.007
+QCA4019_FIRMWARE_FILE_CT_HTT:=firmware-5-ct-full-htt-mgt-community-12.bin-lede.008
 define Download/ath10k-firmware-qca4019-ct-htt
   $(call Download/ct-firmware-htt,QCA4019,ath10k-4019-10-4b)
-  HASH:=b791820962e26ba186d2310c024dd16c5ec44bfbbaf40bfeb77ab30bb297e75f
+  HASH:=8f6434856d6f0207bc3f519cf50d2bf45df1bfcbc69b864ed02fcb5cd5ef6f4b
 endef
 $(eval $(call Download,ath10k-firmware-qca4019-ct-htt))
 
 
-QCA9888_FIRMWARE_FILE_CT:=firmware-5-ct-full-community-12.bin-lede.007
+QCA9888_FIRMWARE_FILE_CT:=firmware-5-ct-full-community-12.bin-lede.008
 define Download/ath10k-firmware-qca9888-ct
   $(call Download/ct-firmware,QCA9888,ath10k-9888-10-4b)
-  HASH:=f96e5d62c9b5d79cad0b0ff702cdd2644c408bcaeb1bd23f340f0425a002c8cd
+  HASH:=6b627746f88c1bfecb872e72c61d6097192e389592e391630d2661b44f13b10d
 endef
 $(eval $(call Download,ath10k-firmware-qca9888-ct))
 
-QCA9888_FIRMWARE_FILE_CT_HTT:=firmware-5-ct-full-htt-mgt-community-12.bin-lede.007
+QCA9888_FIRMWARE_FILE_CT_HTT:=firmware-5-ct-full-htt-mgt-community-12.bin-lede.008
 define Download/ath10k-firmware-qca9888-ct-htt
   $(call Download/ct-firmware-htt,QCA9888,ath10k-9888-10-4b)
-  HASH:=1f6d872f29d1635df55737458fc054adc64803638b4ad220ce0ccb13be5c0010
+  HASH:=4ef46b2bdd3ddc894f79da2dbf90ee04cb58781f3eb193840bd5fdb8624b447b
 endef
 $(eval $(call Download,ath10k-firmware-qca9888-ct-htt))