ath79: add support for Aruba AP-105
authorChris Blake <chrisrblake93@gmail.com>
Sun, 5 May 2019 17:56:03 +0000 (12:56 -0500)
committerChristian Lamparter <chunkeey@gmail.com>
Sat, 18 May 2019 14:44:41 +0000 (16:44 +0200)
SoC: Atheros AR7161-8C1A @ 680 MHz
RAM: 128MB - 2x Etron Technology EM6AB160TSA-5G
NOR: 16MB - 1x MXIC MX25L12845EMI-10G (SPI-NOR)
WI1: Atheros AR9223-AC1A 802.11bgn
WI2: Atheros AR9220-AC1A 802.11an
ETH: Atheros AR8021-BL1E + PoE
LED: Dual-Color Power/Status, Ethernet, WLAN2G and WLAN5G
BTN: 1 x Reset
I2C: AT97SC4303s TPM (needs driver!)
CON: RS232-level 8P8C/RJ45 Console Port - 9600 Baud

Factory installation:

 - Needs a u-boot replacement. See Wiki for
   information on how to do a in-circut flash with
   a SPI-Flasher like a CH314A or flashrom. Wiki page
   can be found at https://openwrt.org/toh/aruba/aruba_ap-105

 - Be careful when dis- and reassembling the device to
   not squish any of the antenna cables in the process!

 - Be sure to make a full 16 MiB backup of your device
   before flashing the new u-boot! This is needed if you
   ever have interest in reverting back to stock firmware.

Not working:

 - TPM (needs a driver)

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
target/linux/ath79/base-files/etc/board.d/02_network
target/linux/ath79/dts/ar7161_aruba_ap-105.dts [new file with mode: 0644]
target/linux/ath79/image/generic.mk

index 5892bac..897b59a 100755 (executable)
@@ -9,6 +9,7 @@ ath79_setup_interfaces()
        local board="$1"
 
        case "$board" in
+       aruba,ap-105|\
        avm,fritz300e|\
        devolo,dvl1200i|\
        devolo,dvl1750c|\
diff --git a/target/linux/ath79/dts/ar7161_aruba_ap-105.dts b/target/linux/ath79/dts/ar7161_aruba_ap-105.dts
new file mode 100644 (file)
index 0000000..45d4d03
--- /dev/null
@@ -0,0 +1,190 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar7100.dtsi"
+
+/ {
+       compatible = "aruba,ap-105", "qca,ar7161";
+       model = "Aruba AP-105";
+
+       chosen {
+               bootargs = "console=ttyS0,9600";
+       };
+
+       aliases {
+               led-boot = &power_green;
+               led-failsafe = &power_red;
+               led-running = &power_green;
+               led-upgrade = &power_green;
+       };
+
+       extosc: ref {
+               compatible = "fixed-clock";
+               #clock-cells = <0>;
+               clock-output-names = "ref";
+               clock-frequency = <40000000>;
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               power_green: power_green {
+                       label = "ap-105:green:power";
+                       gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+               };
+
+               power_red: power_red {
+                       label = "ap-105:red:power";
+                       gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+                       panic-indicator;
+               };
+
+               wifi_2g_red: wifi_2g_red {
+                       label = "ap-105:red:wlan2g";
+                       gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+               };
+
+               wifi_5g_red: wifi_5g_red {
+                       label = "ap-105:red:wlan5g";
+                       gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       ath9k-leds {
+               compatible = "gpio-leds";
+
+               wifi_2g_green {
+                       label = "ap-105:green:wlan2g";
+                       gpios = <&ath9k0 5 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy0tpt";
+               };
+
+               wifi_5g_green {
+                       label = "ap-105:green:wlan5g";
+                       gpios = <&ath9k1 5 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy1tpt";
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               reset {
+                       label = "reset";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       i2c {
+               compatible = "i2c-gpio";
+
+               sda-gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+               scl-gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+
+               /* can be removed on 4.19 */
+               gpios = <&gpio 5 GPIO_ACTIVE_LOW>,
+                       <&gpio 4 GPIO_ACTIVE_LOW>;
+
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               tpm@29 {
+                       compatible = "atmel,at97sc3203s";
+                       reg = <0x29>;
+
+                       /* triggering it, will also kill system */
+                       reset-gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+               };
+       };
+};
+
+&pcie0 {
+       status = "okay";
+
+       ath9k0: wifi@0,11 { /* 2.4 GHz */
+               compatible = "pci168c,0029";
+               mtd-mac-address = <&hwinfo 0x1c>;
+               mtd-mac-address-increment = <1>;
+               reg = <0x8800 0 0 0 0>;
+               #gpio-cells = <2>;
+               gpio-controller;
+       };
+
+       ath9k1: wifi@0,12 { /* 5 GHz */
+               compatible = "pci168c,0029";
+               mtd-mac-address = <&hwinfo 0x1c>;
+               mtd-mac-address-increment = <2>;
+               reg = <0x9000 0 0 0 0>;
+               #gpio-cells = <2>;
+               gpio-controller;
+       };
+};
+
+&uart {
+       status = "okay";
+};
+
+&mdio0 {
+       status = "okay";
+
+       phy-mask = <0x1>;
+
+       phy0: ethernet-phy@0 {
+               reg = <0>;
+       };
+};
+
+&eth0 {
+       status = "okay";
+       mtd-mac-address = <&hwinfo 0x1c>;
+
+       pll-data = <0x00110000 0x00001099 0x00991099>;
+
+       phy-mode = "rgmii";
+       phy-handle = <&phy0>;
+};
+
+&spi {
+       status = "okay";
+       num-cs = <1>;
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <25000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "u-boot";
+                               reg = <0x000000 0x40000>;
+                               read-only;
+                       };
+
+                       partition@40000 {
+                               label = "firmware";
+                               reg = <0x40000 0xfa0000>;
+                               compatible = "denx,uimage";
+                       };
+
+                       hwinfo: partition@fe0000 {
+                               label = "hwinfo";
+                               reg = <0xfe0000 0x10000>;
+                               read-only;
+                       };
+
+                       partition@ff0000 {
+                               label = "u-boot-env";
+                               reg = <0xff0000 0x10000>;
+                               read-only;
+                       };
+               };
+       };
+};
index a96c9d2..dd5843d 100644 (file)
@@ -75,6 +75,14 @@ define Device/seama
   SEAMA_SIGNATURE :=
 endef
 
+define Device/aruba_ap-105
+  ATH_SOC := ar7161
+  DEVICE_TITLE := Aruba AP-105
+  IMAGE_SIZE := 16000k
+  DEVICE_PACKAGES := kmod-i2c-core kmod-i2c-gpio kmod-tpm-i2c-atmel
+endef
+TARGET_DEVICES += aruba_ap-105
+
 define Device/avm_fritz300e
   ATH_SOC := ar7242
   DEVICE_TITLE := AVM FRITZ!WLAN Repeater 300E