openwrt/staging/jogo.git
2 months agokernel: bump 4.19 to 4.19.23 master
Koen Vandeputte [Fri, 15 Feb 2019 10:09:35 +0000 (11:09 +0100)]
kernel: bump 4.19 to 4.19.23

Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 months agokernel: bump 4.14 to 4.14.101
Koen Vandeputte [Fri, 15 Feb 2019 10:09:09 +0000 (11:09 +0100)]
kernel: bump 4.14 to 4.14.101

Refreshed all patches.

Fixes:
- CVE-2019-3819

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 months agokernel: bump 4.9 to 4.9.158
Koen Vandeputte [Fri, 15 Feb 2019 10:05:42 +0000 (11:05 +0100)]
kernel: bump 4.9 to 4.9.158

Refreshed all patches.

Fixes:
- CVE-2019-3819

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 months agobusybox: update to 1.30.1
Hannu Nyman [Thu, 14 Feb 2019 18:51:10 +0000 (20:51 +0200)]
busybox: update to 1.30.1

Minor bugfix release. Fixes for
 * bc/dc
 * sed (backslash parsing for 'w' command)
 * ip (vlan fixes)
 * grep (fixes for -x -v)
 * ls (-i compat)

No need to refresh patches or config defaults

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2 months agoipq40xx: fix ipq40xx_setup_macs for Linksys EA6350v3
Oever González [Thu, 14 Feb 2019 00:13:07 +0000 (18:13 -0600)]
ipq40xx: fix ipq40xx_setup_macs for Linksys EA6350v3

This commit fixes the script that sets the MAC address of the LAN
switch. The LAN MAC address should be the WAN MAC address plus one.

Without this patch the WAN and the LAN interface will use the same
MAC address and an error will be generated.

With this patch all interfaces will have a different MAC address,
consecutive in the following order: WAN, LAN, radio0 and radio1.

Signed-off-by: Oever González <notengobattery@gmail.com>
2 months agoipq8064: Enabling sata port ipq8064 based devices
Roman Glova [Tue, 12 Feb 2019 01:59:00 +0000 (20:59 -0500)]
ipq8064: Enabling sata port ipq8064 based devices

(original text here: https://patchwork.kernel.org/patch/8686761/)

On some SOCs PORTS_IMPL register value is never programmed by the BIOS
and left at zero value. Which means that no sata ports are avaiable for
software. AHCI driver used to cope up with this by fabricating the
port_map if the PORTS_IMPL register is read zero, but recent patch
broke this workaround as zero value was valid for nvme disks.
This patch adds ports-implemented dt bindings as workaround for this issue
in a way that DT can dictate the port_map incase where the SOCs does not
program it already.

This patch is equal to commits:
67f8425d0ee1 ("ipq8064: dts: force AP148 SATA port mapping")
2e7a2c91019c ("ARM: dts: qcom: Move common nodes to ipq8064-v.1.0.dtsi")
in the upstream linux kernel.

Signed-off-by: Roman Glova <roman_glova@epam.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added upstream commits, reorg' commit message]

2 months agoath79: add support for I-O DATA WN-AC1600DGR
INAGAKI Hiroshi [Tue, 5 Feb 2019 08:23:58 +0000 (17:23 +0900)]
ath79: add support for I-O DATA WN-AC1600DGR

I-O DATA WN-AC1600DGR is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.

Specification:

- SoC:      Qualcomm Atheros QCA9557
- RAM:      128 MB
- Flash:    16 MB
- WLAN:     2.4/5 GHz
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz:   3T3R (QCA9880)
- Ethernet: 5x 10/100/1000 Mbps
  - Switch: QCA8337N
- LED/key:  6x/6x(4x buttons, 1x slide switch)
- UART:     through-hole on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of WN-AC1600DGR
2. Connect power cable to WN-AC1600DGR and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Alternative flash instruction using initramfs image:

1. Prepare a computer and TFTP server software with the IP address
"192.168.99.8" and renamed OpenWrt initramfs image
"uImageWN-AC1600DGR"
2. Connect between WN-AC1600DGR and the computer with UART
3. Connect power cable to WN-AC1600DGR, press "4" on the serial
console and enter the U-Boot console
4. execute "tftpboot" command on the console and download initramfs
image from the TFTP server
5. execute "bootm" command and boot OpenWrt
6. On initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
7. Wait ~150 seconds to complete flashing

This commit also removes unnecessary "qca,no-eeprom" property from
the ath10k wifi node.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2 months agoath79: fix qca955x dual pci resource allocation
Santiago Piccinini [Tue, 29 Jan 2019 04:20:44 +0000 (04:20 +0000)]
ath79: fix qca955x dual pci resource allocation

Tested with a dual pci QCA9558 board (LibreRouter v1) in three
configurations: enabling pcie0 only, pcie1 only and both enabled.

Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
2 months agoath79: fix qca955x pcie0 memory size
Santiago Piccinini [Tue, 29 Jan 2019 04:20:56 +0000 (04:20 +0000)]
ath79: fix qca955x pcie0 memory size

Datasheet states that both PCI ranges are of 0x2000000 size:
0x1000_0000-0x11FF_FFF and 0x1200_0000-0x13FF_0000.

Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
2 months agoipq40xx: add support for ASUS Lyra
Marius Genheimer [Tue, 12 Feb 2019 16:19:51 +0000 (17:19 +0100)]
ipq40xx: add support for ASUS Lyra

SoC:   Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores
RAM:   256 MiB (Nanya NT5CC128M16IP-DI)
FLASH: 128 MiB (Macronix NAND)
WiFi0: Qualcomm IPQ4019 b/g/n 2x2
WiFi1: Qualcomm IPQ4019 a/n/ac 2x2
WiFi2: Qualcomm Atheros QCA9886 a/n/ac
BT:    Atheros AR3012
IN:    WPS Button, Reset Button
OUT:   RGB-LED via TI LP5523 9-channel Controller
UART:  Front of Device - 115200 N-8
       Pinout 3.3v - RX - TX - GND (Square is VCC)

Installation:
1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp.
Login credentials are identical to the Web UI.

2. Login to the device via SSH.

3. Flash the initramfs image using

> mtd-write -d linux -i openwrt-image-file

4. Power-cycle the device and wait for OpenWRT to boot.

5. From there flash the OpenWRT-sysupgrade image.

Ethernet-Ports: Although labeled identically, the port next to
the power socket is the LAN port and the other one is WAN. This
is the same behavior as in the stock firmware.

Signed-off-by: Marius Genheimer <mail@f0wl.cc>
[Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh,
reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79,
minor dts touchup, added rng to 4.19 dts]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 months agoipq40xx: ea6350v3: 4.19: enable pseudo rng support
Christian Lamparter [Tue, 12 Feb 2019 17:40:47 +0000 (18:40 +0100)]
ipq40xx: ea6350v3: 4.19: enable pseudo rng support

Robert Marko made a big effort to enable the rng on all
ipq40xx for 4.19, so let's continue the quest.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 months agogemini: Name binary "bootpart.tar.gz"
Linus Walleij [Thu, 7 Feb 2019 19:47:15 +0000 (20:47 +0100)]
gemini: Name binary "bootpart.tar.gz"

This factory binary i supposed to actually be unzipped and
untarred by the user as part of the installation process
(this NAS boots from harddisk), so name it "bootpart.tar.gz"
and not "factory.bin" so it is helpful for users.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 months agokernel: Add missing config option for kernel 4.19
Daniel Engberg [Fri, 8 Feb 2019 12:22:41 +0000 (13:22 +0100)]
kernel: Add missing config option for kernel 4.19

Add CONFIG_USB_ROLE_SWITCH otherwise Octeon 4.19 fails compile

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2 months agompc85xx: 4.19: add missing symbol
Pawel Dembicki [Tue, 12 Feb 2019 14:17:58 +0000 (15:17 +0100)]
mpc85xx: 4.19: add missing symbol

OCEDO Panda was added in b368373f, but only for
4.14 config. This patch fix 4.19 build for generic
and p2020 subtarget.

Signed-off-by: Pawel Dembicki <p.dembicki@wb.com.pl>
2 months agoramips: change status LED for Buffalo WHR-G300N
INAGAKI Hiroshi [Sun, 3 Feb 2019 02:18:09 +0000 (11:18 +0900)]
ramips: change status LED for Buffalo WHR-G300N

Buffalo WHR-G300N has a LED for power status indication, but it is not
connected to the GPIO and cannot be controlled by the kernel. So,
WHR-G300N uses "ROUTER" LED as the system status LED instead.

This commit changes it to use "DIAG" LED insted of "ROUTER" like
WHR-G301N in ath79 target.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2 months agoramips: various Netgear R6120 fixes
David Bauer [Fri, 1 Feb 2019 23:34:43 +0000 (00:34 +0100)]
ramips: various Netgear R6120 fixes

The R6120 has no 5GHz WLAN LED, the assigned GPIO in fact controls
the WAN LED.

Renames the LED accordingly in the device-tree.
Removes the 5GHz WLAN LED trigger.
Adds the correct WAN port LED trigger.

----

Currently, the MAC address for the Netgear R6120 is read from the NVRAM
partition. The offset for the MAC address however is not consistent
across devices or firmware versions.

Switch to using the factory partition like all other Netgear devices do.

----

The LAN ports of the R6120 are labled in reverse on the casing.

Adjust LuCI switchport numbering accordingly.

----

The WiFi eeprom offsets for the R6120 are currently wrong (5GHz offset
is bigger than the partition itself).

Fixes poor performance on 2.4 and 5 GHz.

Signed-off-by: David Bauer <mail@david-bauer.net>
2 months agoramips: add support for I-O DATA WN-AC1167GR
INAGAKI Hiroshi [Tue, 8 Jan 2019 15:20:18 +0000 (00:20 +0900)]
ramips: add support for I-O DATA WN-AC1167GR

I-O DATA WN-AC1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7620A.

Specification:

- SoC     : MediaTek MT7620A
- RAM     : DDR2 64 MB
- Flash   : SPI-NOR 8MB
- WLAN    : 2.4/5 GHz, 2T2R
  - 2.4 GHz: MT7620A (SoC)
  - 5 GHz  : MT7612E
- Ethernet: 10/100/1000 Mbps (ext. MT7530)
- LED/key : 4x/3x (2x buttons, 1x slide-switch)
- UART    : through-hole on PCB
  - J2: TX, GND, RX, Vcc from SoC side
  - 115200n8

Flash instruction using factory image:

1. Boot WN-AC1167GR normaly
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2 months agoath79: proper indentation in image/common-tp-link.mk
Paul Wassi [Sun, 6 Jan 2019 14:27:00 +0000 (15:27 +0100)]
ath79: proper indentation in image/common-tp-link.mk

Add two spaces for proper indentation in image/common-tp-link.mk

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2 months agoath79: fix port order on TL-WR841ND-v7
Paul Wassi [Sat, 5 Jan 2019 22:54:01 +0000 (23:54 +0100)]
ath79: fix port order on TL-WR841ND-v7

The switch ports are seen one to one on the case.
Also remove unneeded secondary port numbers in this
case statement.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2 months agoath79: change ledtrig on GL.iNet AR150
Paul Wassi [Fri, 4 Jan 2019 22:35:09 +0000 (23:35 +0100)]
ath79: change ledtrig on GL.iNet AR150

Change the ledtrig for LAN from netdev to switch.
Although eth1 comes out of the device at a single port,
this port is a switch-port and therefore the LED
must be triggered by that.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2 months agoath79: rename TP-LINK to TP-Link
Paul Wassi [Fri, 4 Jan 2019 21:44:08 +0000 (22:44 +0100)]
ath79: rename TP-LINK to TP-Link

Remove inconsistencies in the vendor's name.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2 months agoar71xx: fix TL-MR3220-v2 switch port order
Paul Wassi [Fri, 4 Jan 2019 21:38:17 +0000 (22:38 +0100)]
ar71xx: fix TL-MR3220-v2 switch port order

Fix the switch port order for proper display on high
level interfaces.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2 months agoar71xx: fix TL-WR741ND-v4 switch port order
Paul Wassi [Fri, 4 Jan 2019 21:37:01 +0000 (22:37 +0100)]
ar71xx: fix TL-WR741ND-v4 switch port order

Fix the switch port order for proper display on high
level interfaces.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2 months agoath79: rename TL-WR740ND-v4 to TL-WR740N-v4
Paul Wassi [Fri, 4 Jan 2019 21:26:01 +0000 (22:26 +0100)]
ath79: rename TL-WR740ND-v4 to TL-WR740N-v4

Give the device the same name it had in ar71xx.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2 months agoath79: fix TL-WR741ND-v4 switch port order
Paul Wassi [Fri, 4 Jan 2019 21:19:28 +0000 (22:19 +0100)]
ath79: fix TL-WR741ND-v4 switch port order

Fix the switch port order for proper display on high
level interfaces.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2 months agokernel: bump 4.19 to 4.19.21
Koen Vandeputte [Wed, 13 Feb 2019 10:38:41 +0000 (11:38 +0100)]
kernel: bump 4.19 to 4.19.21

Refreshed all patches.

Remove upstreamed:
- 0007-ARM-dts-Fix-up-the-D-Link-DIR-685-MTD-partition-info.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 months agokernel: bump 4.14 to 4.14.99
Koen Vandeputte [Wed, 13 Feb 2019 10:38:08 +0000 (11:38 +0100)]
kernel: bump 4.14 to 4.14.99

Refreshed all patches.

Remove upstreamed:
- 950-0434-mmc-bcm2835-Recover-from-MMC_SEND_EXT_CSD.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 months agokernel: bump 4.9 to 4.9.156
Koen Vandeputte [Wed, 13 Feb 2019 10:33:57 +0000 (11:33 +0100)]
kernel: bump 4.9 to 4.9.156

Refreshed all patches.

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 months agodnsmasq: add rapid commit config option
Hans Dedecker [Wed, 13 Feb 2019 09:30:10 +0000 (10:30 +0100)]
dnsmasq: add rapid commit config option

Add config option rapidcommit to enable support for DHCPv4 rapid
commit (RFC4039)

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2 months agoopenssl: add package for openssl.cnf, misc changes
Eneas U de Queiroz [Wed, 30 Jan 2019 10:42:11 +0000 (08:42 -0200)]
openssl: add package for openssl.cnf, misc changes

- Add the /etc/ssl/openssl.cnf as a separate package, to avoid breaking
  the transitional mechanism, allowing libopenssl_1.0* and
  libopenssl_1.1* to coexist.

- Remove the (selecting) dependency on @KERNEL_AIO

- Use global SOURCE_DATE_EPOCH

Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
2 months agoopenssl: optimizations based on ARCH/small flash
Eneas U de Queiroz [Wed, 24 Oct 2018 19:28:59 +0000 (16:28 -0300)]
openssl: optimizations based on ARCH/small flash

Add a patch to enable the option to change the default ciphersuite list
ordering to prefer ChaCha20 over AES-GCM.  This is used by default for
all platforms, except for x86_64 and aarch64. The assumption is that
only the latter have AES-specific CPU instructions and asm code that
uses them in openssl.  Chacha20Poly1305 is 3x faster than AES-256 in
systems without AES instructions, with an equivalent strength.

Disable error messages by default except for devices with small flash or
RAM, to aid debugging.

Disable ASM by default on arm platform with small flash.  Size
difference on mips and powerpc, the other platforms with small flash
devices, are not really relevant (using 100K as a threshold).  All of
the affected platforms are source-only anyway.

Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
2 months agoopenssl: update to version 1.1.1a
Eneas U de Queiroz [Wed, 24 Oct 2018 14:25:00 +0000 (11:25 -0300)]
openssl: update to version 1.1.1a

This version adds the following functionality:
  * TLS 1.3
  * AFALG engine support for hardware accelleration
  * x25519 ECC curve support
  * CRIME protection: disable use of compression by default
  * Support for ChaCha20 and Poly1305

Patches fixing bugs in the /dev/crypto engine were applied, from
https://github.com/openssl/openssl/pull/7585

This increses the size of the ipk binray on MIPS32 by about 32%:
old:
693.941 bin/packages/mips_24kc/base/libopenssl1.0.0_1.0.2q-2_mips_24kc.ipk
193.827 bin/packages/mips_24kc/base/openssl-util_1.0.2q-2_mips_24kc.ipk

new:
912.493 bin/packages/mips_24kc/base/libopenssl1.1_1.1.1a-2_mips_24kc.ipk
239.316 bin/packages/mips_24kc/base/openssl-util_1.1.1a-2_mips_24kc.ipk

Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
2 months agoopenssl: add configuration options, disable ssl3
Eneas U de Queiroz [Mon, 22 Oct 2018 14:32:56 +0000 (11:32 -0300)]
openssl: add configuration options, disable ssl3

Adds the following configuration options:
* using optimized assembler code (was always on before)
* use of x86 SSE2 instructions
* dyanic engine support
* include error messages
* Camellia, Gost, Idea, MDC2, Seed & Whirlpool algorithms
* RFC3779, CMS protocols
* VIA padlock hardware acceleration engine

Installs openssl.cnf with the library as it is used by engines
independent of the openssl util.

Fixes DTLS option that was innefective before.

Disables insecure SSL3 protocol and SHA0.

Adds openwrt-specific targets to Configure script, including asm support
for i386, ppc and mips64.

Strips building dirs from CFLAGS shown in binary.

Skips the fuzz directory during build.

Removed include/crypto/devcrypto.h that was included here, to use the
cryptodev-linux package, now that it was been moved from the packages
feed to the main openwrt repository.

This decreses the size of the ipk binray on MIPS32 by about 3.3%:
old:
706.957 bin/packages/mips_24kc/base/libopenssl1.0.0_1.0.2q-2_mips_24kc.ipk
199.294 bin/packages/mips_24kc/base/openssl-util_1.0.2q-2_mips_24kc.ipk

new:
693.941 bin/packages/mips_24kc/base/libopenssl1.0.0_1.0.2q-2_mips_24kc.ipk
193.827 bin/packages/mips_24kc/base/openssl-util_1.0.2q-2_mips_24kc.ipk

Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
2 months agobase-files: fix ucert verification
Felix Fietkau [Tue, 12 Feb 2019 15:37:30 +0000 (16:37 +0100)]
base-files: fix ucert verification

ucert needs to check the firmware part with metadata, but without the signature.
Use the new fwtool mode to extract that without altering the firmware image inside
the check

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 months agofwtool: add support for extracting the truncated data part to stdout
Felix Fietkau [Tue, 12 Feb 2019 15:24:14 +0000 (16:24 +0100)]
fwtool: add support for extracting the truncated data part to stdout

This allows extracing the firmware + metadata from a signed firmware without
altering the original image file

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 months agofwtool: do not strip metadata if extracting signature
Felix Fietkau [Tue, 12 Feb 2019 14:59:11 +0000 (15:59 +0100)]
fwtool: do not strip metadata if extracting signature

This allows the signature to cover the metadata area

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 months agohostapd: fix race condition in mesh new peer handling
Felix Fietkau [Tue, 12 Feb 2019 13:26:04 +0000 (14:26 +0100)]
hostapd: fix race condition in mesh new peer handling

Avoid trying to add the same station to the driver multiple times

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 months agohostapd: send wpa_supplicant logging output to syslog
Felix Fietkau [Tue, 12 Feb 2019 13:04:07 +0000 (14:04 +0100)]
hostapd: send wpa_supplicant logging output to syslog

Helpful for debugging network connectivity issues

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 months agomac80211: brcmfmac: backport early changes queued for the Linux 5.1
Rafał Miłecki [Tue, 12 Feb 2019 13:17:46 +0000 (14:17 +0100)]
mac80211: brcmfmac: backport early changes queued for the Linux 5.1

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2 months agomac80211: brcmfmac: backport remaining patches from the Linux 5.0
Rafał Miłecki [Tue, 12 Feb 2019 12:43:06 +0000 (13:43 +0100)]
mac80211: brcmfmac: backport remaining patches from the Linux 5.0

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2 months agoiproute2: tc: reduce size of dynamic symbol table
Tony Ambardar [Fri, 14 Dec 2018 07:49:32 +0000 (23:49 -0800)]
iproute2: tc: reduce size of dynamic symbol table

In the case of SHARED_LIBS=y, don't use -export-dynamic to place *all*
symbols into the dynamic symbol table. Instead, use --dynamic-list to
export a smaller set of symbols similar to that defined in static-syms.h
in the case of SHARED_LIBS=n, avoiding an 11 KB tc package size increase.

Also increment PKG_RELEASE.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2 months agoiproute2: tc: enable and fix support for using .so plugins
Tony Ambardar [Thu, 13 Dec 2018 19:48:55 +0000 (11:48 -0800)]
iproute2: tc: enable and fix support for using .so plugins

This enables using the tc module m_xt.so, which uses the act_ipt kernel
module to allow tc actions based on iptables targets. e.g.

   tc filter add dev eth0 parent 1: prio 10 protocol ip \
   u32 match u32 0 0 action xt -j DSCP --set-dscp-class BE

Make the SHARED_LIBS parameter configurable and based on tc package
selection.

Fix a problem using the tc m_xt.so plugin as also described in
https://bugs.debian.org/868059:

  Sync include/xtables.h from iptables to make sure the right offset is
  used when accessing structure members defined in libxtables. One could
  get “Extension does not know id …” otherwise. (See also: #868059)

Patch to sync the included xtables.h with system iptables 1.6.x. This
continues to work with iptables 1.8.2.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2 months agoiproute2: simplify linking libelf for eBFP/XDP object file support
Tony Ambardar [Sat, 24 Nov 2018 00:33:45 +0000 (16:33 -0800)]
iproute2: simplify linking libelf for eBFP/XDP object file support

Simplify build and runtime dependencies on libelf, which allows tc and ip
to load BPF and XDP object files respectively.

Preserve optionality of libelf by having configuration script follow the
HAVE_ELF environment variable, used similarly to the HAVE_MNL variable.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2 months agoiproute2: use tc package variant to limit other package sizes
Tony Ambardar [Sun, 16 Dec 2018 02:26:48 +0000 (18:26 -0800)]
iproute2: use tc package variant to limit other package sizes

Replace the old 'tc' with a singleton package variant which will be used
to enable additional functionality and limit it only to tc. Non-variant
packages will only be installed during 'tiny' variant builds, hence will
be configured without extra features, thus preserving previously limited
functionality and reduced package sizes.

Also set ip-tiny as the default variant, and install 'tiny' versions of
development libraries.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2 months agoiproute2: simplify Makefile, patches and fix feature detection
Tony Ambardar [Sat, 24 Nov 2018 07:56:24 +0000 (23:56 -0800)]
iproute2: simplify Makefile, patches and fix feature detection

Compile-based feature detection (e.g. xtables, ipset support) was broken
due to silent compilation errors in the configure script, caused by a
Makefile variable KERNEL_INCLUDE referring to kernel build headers. Use
userspace headers by setting the same "user_headers" kernel include path
as used for the iptables build.

Remove redundant or unused Build/Configure definitions from package
Makefile, including KERNEL_INCLUDE, LIBC_INCLUDE and DBM includes.

Don't pass LDFLAGS within MAKE_FLAGS as this interferes with LDFLAGS in
tc/Makefile and masks a link parameter ("-Wl,-export-dynamic"). Instead,
use standard TARGET_LDFLAGS.

Replace EXTRA_CCOPTS in MAKE_FLAGS with cleaner TARGET_CPPFLAGS, and also
drop now unneeded patch 150-extra-ccopts.patch.

Enable defining XT_LIB_DIR from Makefile, needed to set the iptables
modules directory to something other than /lib/xtables, and also add
libxtables dependency. Both are needed with working xtables detection.
Note that libxtables is also pulled in by iptables, firewall or luci, so
this change has no size impact in most cases.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2 months agoiproute2: fix broken configuration patch
Tony Ambardar [Fri, 23 Nov 2018 09:09:23 +0000 (01:09 -0800)]
iproute2: fix broken configuration patch

Since v4.13, iproute2 switched to a config.mk file with greater use of
pkg-config for library/feature detection. Replace the old Config patch
with one modifying the configure script but enabling the same changes:
 - explicitly disable TC_CONFIG_ATM
 - rely on feature detection for IP_CONFIG_SETNS and TC_CONFIG_XT

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2 months agobase-files: enable BPF JIT sysctl by default
Tony Ambardar [Tue, 18 Dec 2018 06:13:22 +0000 (22:13 -0800)]
base-files: enable BPF JIT sysctl by default

Set net.core.bpf_jit_enable=1 in /etc/sysctl.d/10-default.conf.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2 months agokernel: enable CONFIG_BPF_JIT by default
Tony Ambardar [Tue, 18 Dec 2018 05:29:33 +0000 (21:29 -0800)]
kernel: enable CONFIG_BPF_JIT by default

Enable the built-in BPF JIT compiler for all 4.9, 4.14 and 4.19 kernels,
which should speed up cBPF and eBPF-based packet filtering (tc, iptables)
and packet sniffing (libpcap, tcpdump, fwknopd, etc).

This has minimal kernel size impact, increasing the size of uImage-lzma
(normally ~2 MB on mips_24kc or mips64el_mips64) by 5 KB for the MIPS32
arch cBPF JIT and by 9 KB for the MIPS64 arch eBPF JIT, on kernel 4.14.

With JIT enabled (cBPF only), the standard BPF test module (test_bpf.ko)
running on a DIR-835 (mips_24kc) used 33 CPU seconds, but 68 without JIT.

This change aligns with the notion of OpenWRT as the network go-to swiss
army knife for packet handling, especially on CPU-constrained platforms.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2 months agokernel/modules: add kmod-bpf-test package
Tony Ambardar [Mon, 19 Nov 2018 17:16:48 +0000 (09:16 -0800)]
kernel/modules: add kmod-bpf-test package

Add the test_bpf module that runs various test vectors against the BPF
interpreter or BPF JIT compiler. The module must be manually loaded, as
with the kmod-crypto-test module which serves a similar purpose.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2 months agokernel/modules: add kmod-sched-bpf package
Tony Ambardar [Fri, 26 Oct 2018 09:16:32 +0000 (02:16 -0700)]
kernel/modules: add kmod-sched-bpf package

Add cls_bpf and act_bpf modules for additional tc classifier and action
support of cBPF and eBPF.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2 months agokernel/modules: add kmod-sched-ipset package
Tony Ambardar [Tue, 30 Oct 2018 13:27:04 +0000 (06:27 -0700)]
kernel/modules: add kmod-sched-ipset package

Add em_ipset module to support tc filter classification by IP set. Build
as a standalone package to help avoid pulling in rest of kmod-sched and
isolate new dependency on kmod-ipt-ipset.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2 months agokernel/modules: kmod-sched: add some common, useful actions
Tony Ambardar [Tue, 30 Oct 2018 12:50:51 +0000 (05:50 -0700)]
kernel/modules: kmod-sched: add some common, useful actions

Add act_pedit, act_csum, act_gact and act_simple modules for additional
tc action support. Module act_simple helps with debug and logging, similar
to iptables LOG target, while act_gact provides common generic actions.
Modules act_pedit and act_csum support general packet mangling, and have
been the subject of feature requests and forum discussions (e.g. DSCP),
as well as being added to the Turris OS fork of OpenWrt ~2 years ago.

Also select dependency kmod-lib-crc32c to support act_csum.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2 months agokernel/modules: kmod-sched-core: add missing dependency, useful module
Tony Ambardar [Tue, 30 Oct 2018 12:50:51 +0000 (05:50 -0700)]
kernel/modules: kmod-sched-core: add missing dependency, useful module

All tc ematch modules, including those in kmod-sched-core and kmod-sched,
use cls_basic as a core dependency. Relocate cls_basic from kmod-sched to
kmod-sched-core to avoid requiring kmod-sched unnecessarily.

This change is also backwards compatible since any past tc ematch users
will have had to install both kmod-sched-core and kmod-sched anyway.

Add the matchall kernel module cls_matchall introduced in kernel 4.8. The
matchall classifier matches every packet and allows the user to apply
actions on it. It is a simpler, more efficient replacement for the common
but cryptic tc classifier idiom "u32 match u32 0 0".

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2 months agoath79: add support for Xiaomi Mi Router 4Q
David Bauer [Fri, 1 Feb 2019 19:48:41 +0000 (20:48 +0100)]
ath79: add support for Xiaomi Mi Router 4Q

Hardware
--------
CPU:   Qualcomm Atheros QCA9561
RAM:   64M DDR2
FLASH: 16M SPI-NOR
ETH:   1x WAN - 2x LAN
WiFi:  QCA9561 3T3R
BTN:   1x Reset - 1x WPS
LED:   1x Blue - 1x Red - 1x Yellow
UART:  TX - GND - RX - VCC (From ethernet port)
       115200n8 - 3.3V

Installation
------------
1. Connect to the device via UART.

2. Interrupt the U-Boot on power-on by pressing enter when prompted.

3. Connect you computer to one of the routers LAN ports.
   Assign yourself the IP 192.168.31.10/24.
   Copy the OpenWRT initramfs image to a tftp server root directory.
   Rename the image to 'x4q.bin'.

4. Load the initramfs image to the router by executing following command
   in U-Boot. The image will boot afterwards.

   > tftpboot 0x81000000 x4q.bin; bootm

5. SCP the sysupgrade-image into '/tmp'.
   Remember to assign yourself an IP in 192.168.1.0/24 for this step!

6. Install OpenWRT permanently by executing

   > sysupgrade -n /tmp/<OpenWRT-sysupgrade-image>

Signed-off-by: David Bauer <mail@david-bauer.net>
2 months agogemini: Fix kmod-led-trig-heartbeat typo
Linus Walleij [Thu, 7 Feb 2019 19:47:07 +0000 (20:47 +0100)]
gemini: Fix kmod-led-trig-heartbeat typo

It's kmod-ledtrig-* not kmod-led-trig-*.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[extended subject]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 months agomac80211: ath10k: support for management rate control
Sven Eckelmann [Fri, 8 Feb 2019 20:20:20 +0000 (21:20 +0100)]
mac80211: ath10k: support for management rate control

Issues a wmi command to firmware when multicast rate change is received with the
new BSS_CHANGED_MCAST_RATE flag.  Also fixes the incorrect fixed_rate setting
for CCK rates which got introduced with addition of ath10k_rates_rev2 enum.

By default the firmware uses 1Mbps and 6Mbps rate for management packets
in 2G and 5G bands respectively. But when the user selects different
basic rates from the userspace, we need to send the management
packets at the lowest basic rate selected by the user.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2 months agoath10k-ct: support for management rate control
Sven Eckelmann [Fri, 8 Feb 2019 20:20:20 +0000 (21:20 +0100)]
ath10k-ct: support for management rate control

By default the firmware uses 1Mbps and 6Mbps rate for management packets
in 2G and 5G bands respectively. But when the user selects different
basic rates from the userspace, we need to send the management
packets at the lowest basic rate selected by the user.

This change makes use of WMI_VDEV_PARAM_MGMT_RATE param for configuring the
management packets rate to the firmware.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2 months agoath10k-firmware: update Candela Tech firmware images
Christian Lamparter [Sun, 10 Feb 2019 17:27:45 +0000 (18:27 +0100)]
ath10k-firmware: update Candela Tech firmware images

Release notes since last time:

2019-02-08:
  Fix rate-ctrl assert related to bad logic that tried to guess
  that lower bandwidth probes were automatically successful if
  higher was. The NSS mismatch that can happen here caused the
  assert. Just comment out the offending code
  (per comment from original QCA code). This is bug 69.

2019-02-10:
  Fix bssid mis-alignment that broke 4-addr vlan mode (bug 67).
  Original buggy commit was
  commit 2bf89e70ecd1 ("dev-ds: Better packing of wal_vdev struct.")

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 months agobuild: add KERNEL_ENTRY and sort DEFAULT_DEVICE_VARS
Christian Lamparter [Wed, 6 Feb 2019 16:41:49 +0000 (17:41 +0100)]
build: add KERNEL_ENTRY and sort DEFAULT_DEVICE_VARS

The KERNEL_ENTRY was missing from the DEFAULT_DEVICE_VARS.

This bug was discovered while preparing alternative images
for the mpc85xx's TP-Link WDR4900-V1, which all failed to
boot due to this:
|## Booting kernel from Legacy Image at 02000000 ...
|   Image Name:   POWERPC OpenWrt Linux-4.14.96
|   Image Type:   PowerPC Linux Kernel Image (uncompressed)
|   Data Size:    2056568 Bytes = 2 MiB
|   Load Address: 01000000
|   Entry Point:  00000000
|   Verifying Checksum ... OK

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 months agomac80211: brcmfmac: fix a possible NULL pointer dereference
Rafał Miłecki [Mon, 11 Feb 2019 10:25:54 +0000 (11:25 +0100)]
mac80211: brcmfmac: fix a possible NULL pointer dereference

This fixes a possible crash in the brcmf_fw_request_nvram_done():
[   31.687293] Backtrace:
[   31.689760] [<c004fb4c>] (__wake_up_common) from [<c004fc38>] (__wake_up_locked+0x1c/0x24)
[   31.698043]  r10:c6794000 r9:00000009 r8:00000001 r7:bf54dda0 r6:a0000013 r5:c78e7d38
[   31.705928]  r4:c78e7d3c r3:00000000
[   31.709528] [<c004fc1c>] (__wake_up_locked) from [<c00502a8>] (complete+0x3c/0x4c)
[   31.717148] [<c005026c>] (complete) from [<bf54590c>] (brcmf_fw_request_nvram_done+0x5c8/0x6a4 [brcmfmac])
[   31.726818]  r7:bf54dda0 r6:c6794000 r5:00001990 r4:c6782380
[   31.732544] [<bf545344>] (brcmf_fw_request_nvram_done [brcmfmac]) from [<c0204e40>] (request_firmware_work_func+0x38/0x60)
[   31.743607]  r10:00000008 r9:c6bdd700 r8:00000000 r7:c72c3cd8 r6:c67f4300 r5:c6bda300
[   31.751493]  r4:c67f4300
[   31.754046] [<c0204e08>] (request_firmware_work_func) from [<c0034458>] (process_one_work+0x1e0/0x318)
[   31.763365]  r4:c72c3cc0
[   31.765913] [<c0034278>] (process_one_work) from [<c0035234>] (worker_thread+0x2f4/0x448)
[   31.774107]  r10:00000008 r9:00000000 r8:c6bda314 r7:c72c3cd8 r6:c6bda300 r5:c6bda300
[   31.781993]  r4:c72c3cc0
[   31.784545] [<c0034f40>] (worker_thread) from [<c003984c>] (kthread+0x100/0x114)
[   31.791949]  r10:00000000 r9:00000000 r8:00000000 r7:c0034f40 r6:c72c3cc0 r5:00000000
[   31.799836]  r4:c735dc00 r3:c79ed540
[   31.803438] [<c003974c>] (kthread) from [<c00097d0>] (ret_from_fork+0x14/0x24)
[   31.810672]  r7:00000000 r6:00000000 r5:c003974c r4:c735dc00
[   31.816378] Code: e5b53004 e1a07001 e1a06002 e243000c (e5934000)
[   31.822487] ---[ end trace a0ffbb07a810d503 ]---

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2 months agoar71xx: add rssileds for xw devices
Koen Vandeputte [Mon, 11 Feb 2019 08:24:11 +0000 (09:24 +0100)]
ar71xx: add rssileds for xw devices

Commit 7ebbbda29377 ("ar71xx: ubnt-(xm,xw): fix LED RSSI indication")
adds support for using the RSSI strenght via LEDS.

The rssileds package addition got lost during altering the patch.
Add it again to fix this.

Fixes: 7ebbbda29377 ("ar71xx: ubnt-(xm,xw): fix LED RSSI indication")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 months agotools/mpfr: Update to 4.0.2
Daniel Engberg [Sun, 10 Feb 2019 11:32:19 +0000 (11:32 +0000)]
tools/mpfr: Update to 4.0.2

Update mpfr to 4.0.2
Use official site as last resort
Force thread-safety functionality
Refresh patches

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2 months agotools/bison: Update to 3.3.2
Daniel Engberg [Sun, 10 Feb 2019 12:16:30 +0000 (12:16 +0000)]
tools/bison: Update to 3.3.2

Update bison to 3.3.2
Enable pthreads support
Refresh patches

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2 months agotools/sed: Update to 4.7
Daniel Engberg [Sun, 10 Feb 2019 12:35:19 +0000 (12:35 +0000)]
tools/sed: Update to 4.7

Update sed to 4.7
Enable pthreads support

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2 months agotools/tar: Update to 1.31
Daniel Engberg [Sun, 10 Feb 2019 11:53:02 +0000 (11:53 +0000)]
tools/tar: Update to 1.31

Update tar to 1.31
Fixes CVE-2018-20482
Switch to tar.xz tarball
Refresh patches

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2 months agoglibc: update to latest 2.27 commit [BZ #24180]
Hans Dedecker [Sat, 9 Feb 2019 19:54:52 +0000 (20:54 +0100)]
glibc: update to latest 2.27 commit [BZ #24180]

9f44fa22cb Add compiler barriers around modifications of the robust mutex list for pthread_mutex_trylock. [BZ #24180]

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2 months agovti: remove setting default firewall zone to wan
Hans Dedecker [Sat, 9 Feb 2019 19:59:55 +0000 (20:59 +0100)]
vti: remove setting default firewall zone to wan

Same reasoning as in bdedb798150a58ad7ce3c4741f2f31df97e84c3f; don't set
default firewall zone to wan as the firewall zone for the vti interface
can be configured in the firewall config or it makes it impossible not to
specify a firewall zone for the vti interface.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2 months agoipip: remove setting default firewall zone to wan
Hans Dedecker [Sat, 9 Feb 2019 19:48:11 +0000 (20:48 +0100)]
ipip: remove setting default firewall zone to wan

Same reasoning as in bdedb798150a58ad7ce3c4741f2f31df97e84c3f; don't set
default firewall zone to wan as the firewall zone for the ipip interface
can be configured in the firewall config or it makes it impossible not to
specify a firewall zone for the ipip interface.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2 months agokernel: fold xt_FLOWOFFLOAD fixes into the main patch
Felix Fietkau [Thu, 31 Jan 2019 17:26:30 +0000 (18:26 +0100)]
kernel: fold xt_FLOWOFFLOAD fixes into the main patch

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 months agonetfilter: fix checking method of conntrack helper
HsiuWen Yen [Thu, 31 Jan 2019 16:45:22 +0000 (00:45 +0800)]
netfilter: fix checking method of conntrack helper

This patch uses nfct_help() to detect whether an established connection
needs conntrack helper instead of using test_bit(IPS_HELPER_BIT,
&ct->status).

The reason for this modification is that IPS_HELPER_BIT is only set when
the conntrack helper is attached by explicit CT target.

However, in the case that a device enables conntrack helper via the other
ways (e.g., command "echo 1 > /proc/sys/net/netfilter/nf_conntrack_helper")
, the status of IPS_HELPER_BIT will not present any change. That means the
IPS_HELPER_BIT might lose the checking ability in the context.

Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
2 months agobase-files: do not strip fwtool signature data during check
Felix Fietkau [Sat, 9 Feb 2019 13:34:12 +0000 (14:34 +0100)]
base-files: do not strip fwtool signature data during check

Same reason as in commit 9808bd279927bcd2d3a78d19a55229b93bbbcf05 -
sysupgrade --test must not alter the image in any way

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 months agoar71xx: ubnt-(xm,xw): fix LED RSSI indication
Lech Perczak [Tue, 11 Sep 2018 21:50:56 +0000 (23:50 +0200)]
ar71xx: ubnt-(xm,xw): fix LED RSSI indication

When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti XM and XW family, it missed connection to actual interface.
Therefore create the mapping to interface, so RSSI LEDs work without
additional configuration, after starting rssileds service.

Also add the required package for this.

While at that, remove coefficients needed for PWM LEDs, as XM and XW
boards do not support PWM LEDs.

Tested-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[Squashed commits + remove custom device_packages + slighty rewrite the commit msg]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 months agoar71xx: fix RB941-2nD detection
Julien Rabier [Mon, 4 Feb 2019 20:03:35 +0000 (21:03 +0100)]
ar71xx: fix RB941-2nD detection

Some hAP lite routers aren't detected because
/proc/cpuinfo shows "RouterBOARD RB941-2nD"
instead of "RouterBOARD 941-2nD".

Fix that.

Signed-off-by: Julien Rabier <taziden@flexiden.org>
[Alter string to include all flavours + slight rewrite of commit msg]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 months agoar71xx: fix Arduino Yun enabling of level shifters outputs
Edoardo Scaglia [Fri, 1 Feb 2019 15:43:46 +0000 (16:43 +0100)]
ar71xx: fix Arduino Yun enabling of level shifters outputs

As show in Arduino Yun schematic [1] GPIO 21 and 22 are connected to
output enable pin (OE) of two NTB01xx level shifters.

NTB01xx datasheets [2] [3] states that OE pin are active-high
therefore we should initialize GPIO 21 (DS_GPIO_OE) and GPIO 22
(DS_GPIO_OE2) accordingly to actually enable level shifters outputs.

[1] https://www.arduino.cc/en/uploads/Main/arduino-Yun-schematic.pdf
[2] https://www.nxp.com/docs/en/data-sheet/NTB0102.pdf
[3] https://www.nxp.com/docs/en/data-sheet/NTB0104.pdf

Signed-off-by: Edoardo Scaglia <edoardo.87@gmail.com>
2 months agokernel: add missing symbols to 4.19
Petr Štetiar [Thu, 3 Jan 2019 19:20:19 +0000 (20:20 +0100)]
kernel: add missing symbols to 4.19

While preparing 4.19 for imx6 and test building it with
CONFIG_ALL_KMODS=y with verbose mode enabled, I was asked by kernel
config about few missing symbols/modules

Let's add them to the generic config.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[slight rewrite of commit log]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 months agokernel: bump 4.19 to 4.19.20
Koen Vandeputte [Thu, 7 Feb 2019 10:34:28 +0000 (11:34 +0100)]
kernel: bump 4.19 to 4.19.20

Refreshed all patches.

Remove upstreamed:
- 100-arm-cns3xxx-fix-writing-to-wrong-PCI-registers-after.patch

Altered patches:
- 721-phy_packets.patch

Compile-tested on: imx6
Runtime-tested on: imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 months agokernel: bump 4.14 to 4.14.98
Koen Vandeputte [Thu, 7 Feb 2019 10:10:31 +0000 (11:10 +0100)]
kernel: bump 4.14 to 4.14.98

Refreshed all patches.

Remove upstreamed:
- 100-arm-cns3xxx-fix-writing-to-wrong-PCI-registers-after.patch

Altered patches:
- 721-phy_packets.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 months agokernel: bump 4.9 to 4.9.155
Koen Vandeputte [Thu, 7 Feb 2019 10:32:51 +0000 (11:32 +0100)]
kernel: bump 4.9 to 4.9.155

Refreshed all patches.

Remove upstreamed:
- 100-arm-cns3xxx-fix-writing-to-wrong-PCI-registers-after.patch

Altered patches:
- 721-phy_packets.patch

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 months agokernel: bump 3.18 to 3.18.134
Koen Vandeputte [Thu, 7 Feb 2019 10:08:08 +0000 (11:08 +0100)]
kernel: bump 3.18 to 3.18.134

Refreshed all patches.

Compile-tested on: adm5120
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 months agomac80211: rt2x00: remove patch causing low tx power
Daniel Golle [Fri, 8 Feb 2019 03:50:47 +0000 (04:50 +0100)]
mac80211: rt2x00: remove patch causing low tx power

Remove 980-rt2x00-reduce-power-consumption-on-mt7620.patch which in
combination with the most recently added patch reportedly causes TX
power to be too weak.

"without patches rssi on receiver is ~ -23dBm with 980 about -35dBm,
with both patches drops below -40dBm. with 987 only ~-28dBm"

We may need to reconsider this once we have implemented TSSI.

Fixes: cdb58b2bfe ("mac80211: rt2x00: reduce tx power to nominal level on RT6352")
Reported-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 months agocurl: bump to 7.64.0
Deng Qingfang [Fri, 8 Feb 2019 03:07:04 +0000 (11:07 +0800)]
curl: bump to 7.64.0

Fixed CVEs:

CVE-2018-16890
CVE-2019-3822
CVE-2019-3823

For other changes in version 7.64.0 see https://curl.haxx.se/changes.html#7_64_0

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2 months agomac80211: rt2x00: reduce tx power to nominal level on RT6352
Daniel Golle [Thu, 7 Feb 2019 23:03:40 +0000 (00:03 +0100)]
mac80211: rt2x00: reduce tx power to nominal level on RT6352

Current implementation of RT6352 support provides too high tx power
at least on iPA/eLNA devices. Reduce amplification of variable gain
amplifier by 6dB to match board target power of 17dBm.
Transmited signal strength with this patch is similar to that of
stock firmware or pandorabox firmware. Throughput measured with iperf
improves. Device tested: Xiaomi Miwifi Mini.

Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 months agogre: remove setting default firewall zone to wan
Florian Eckert [Thu, 11 Oct 2018 11:10:56 +0000 (13:10 +0200)]
gre: remove setting default firewall zone to wan

There are two problems with this behaviour that the zone is set to wan
if no zone config option is defined in the interface section.

* The zone for the interface is "normally" specified in the firewall
config file. So if we have defined "no" zone for this interface zone
option is set now to "wan" additonaly if we add the interface in the firewall
config section to the "lan" zone, the interface is added to lan and wan at once.

iptables-save | grep <iface>

This is not what I expect.

* If I do not want to set a zone to this interface it is not possible.

Remove the default assigment to wan if no zone option is defined.
If some one need the option it stil possible to define this option.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
2 months agoath79: ag71xx: Fix tx queue timeouts during ifup
Petr Štetiar [Thu, 3 Jan 2019 02:25:11 +0000 (03:25 +0100)]
ath79: ag71xx: Fix tx queue timeouts during ifup

On ath79 and UBNT Bullet M XW (ar9342) I was experiencing weird issues during
network setup[1] which I was able to reproduce easily with following commands:

 uci set network.lan.ipaddr='192.168.1.20'
 uci commit network
 ifup lan

Which resulted after some time in:

 ...
 WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:461 dev_watchdog+0x16c/0x280
 NETDEV WATCHDOG: eth0 (ag71xx): transmit queue 0 timed out
 ...

Sometimes I wasn't able to use networking anymore, sometimes it was enough to
just ifdown/ifup lan and network was backup. On ar71xx it was all working just
fine.

I've found out, that it was happening because ag71xx_poll() wasn't called, thus
the TX queue wasn't emptied. The ag71xx_poll() is being called from napi
hrtimer, which is enabled by napi_schedule() in ar71xx_interrupt(), but since
no interrupts were ever fired again after ag71xx_stop() was called, it was
always leading to tx queue timeouts:

 *** ag71xx_hard_start_xmit()
 eth0: packet injected into TX queue
 eth0: raw intr=00000001 TXPS POLL
 eth0: enable polling mode
 eth0: processing TX ring, flush=no
 eth0: disable polling mode, rx=1, tx=1,limit=32

 ( `ifup lan done here` )

 *** ag71xx_stop()
 *** ag71xx_open()
 *** ag71xx_hw_enable()
 IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
 IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
 *** ag71xx_hard_start_xmit()
 eth0: packet injected into TX queue
 *** ag71xx_hard_start_xmit()
 eth0: packet injected into TX queue
 ...
 WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x164/0x274

So I've looked at ag71xx_stop() in ar71xx, added the missing bits to ath79 and
fixed this issue.

1. https://github.com/openwrt/openwrt/pull/1635#issuecomment-448638246

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[move ag->link before ag71xx_hw_disable to retain ordering as original]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2 months agokernel: rename symbol in kernel 4.19 config
Koen Vandeputte [Thu, 7 Feb 2019 12:01:35 +0000 (13:01 +0100)]
kernel: rename symbol in kernel 4.19 config

A symbol was renamed upstream starting from kernel 4.18 [1]

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?h=v5.0-rc5&id=34b13e5e4641c0e9e0aad471a6d8dfb7999276f1

2 months agonat46: Fix mirror hash
Hauke Mehrtens [Thu, 7 Feb 2019 10:12:49 +0000 (11:12 +0100)]
nat46: Fix mirror hash

The package hash does not match the one of the package found on the
mirrors and which is generated when I do the git clone.

Fixes: 4856fa30a6c ("nat46: import for routing, add myself as maintainer")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 months agobrcm2708: fix early bootloader config restore
Stijn Tintel [Tue, 5 Feb 2019 02:34:01 +0000 (04:34 +0200)]
brcm2708: fix early bootloader config restore

Restoring the bootloader config before rebooting fails:
tar: invalid tar magic

Add the -z option to the tar command to fix this.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2 months agobrcm2708: drop 4.9 support
Stijn Tintel [Sat, 2 Feb 2019 20:53:15 +0000 (21:53 +0100)]
brcm2708: drop 4.9 support

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2 months agoath79: add support for TP-LINK Archer C7 v4
Oldřich Jedlička [Tue, 1 Jan 2019 22:11:49 +0000 (23:11 +0100)]
ath79: add support for TP-LINK Archer C7 v4

TP-Link Archer C7 v4 is a dual-band AC1750 router, based on the
Qualcomm/Atheros QCA9561 SoC + QCA9880.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
   via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
   and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
   the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
2 months agobuild: Fix missing device variables for artifacts
Petr Štetiar [Fri, 18 Jan 2019 08:25:59 +0000 (09:25 +0100)]
build: Fix missing device variables for artifacts

It was reported to me today on IRC, that building of artifacts doesn't
work properly if the concat_cmd references DEVICE_NAME variable. I've
found out, that it's due to missing call of Device/Export in artifacts
building code path, so this patch adds the missing Device/Export call
which in turn exports DEFAULT_DEVICE_VARS into the artifacts
environment.

Fixes: 493c9a35516c ("build: Introduce building of artifacts")
Tested-by: Oskari Lemmela <oskari@lemmela.net>
Reported-by: Oskari Lemmela <oskari@lemmela.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 months agoramips: drop m25p,chunked-io from dts
Chuanhong Guo [Mon, 28 Jan 2019 06:37:07 +0000 (14:37 +0800)]
ramips: drop m25p,chunked-io from dts

This option was a spi nor hack which is dropped in commit
bcf4a5f474 ("ramips: remove chunked-io patch and set spi->max_transfer_size instead")

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [edit message]
2 months agoramips: enable MT7610E 5GHz radio of MT7620a_MT7610e EVB
Deng Qingfang [Wed, 9 Jan 2019 12:54:34 +0000 (20:54 +0800)]
ramips: enable MT7610E 5GHz radio of MT7620a_MT7610e EVB

This enables MT7610E of the EVB

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2 months agoramips: add kmod-mt76x2 to WeVo 11AC NAS
Ju Se Hoon [Tue, 8 Jan 2019 08:54:19 +0000 (17:54 +0900)]
ramips: add kmod-mt76x2 to WeVo 11AC NAS

The WeVo 11AC NAS has a MT7612E 802.11ac chip on the PCB.

Signed-off-by: Ju Se Hoon <joosahoon@gmail.com>
[renamed author from Albis-dev to real name, editted commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 months agotoolchain/musl: update to version 1.1.21
Christian Lamparter [Tue, 22 Jan 2019 15:24:11 +0000 (16:24 +0100)]
toolchain/musl: update to version 1.1.21

<https://www.openwall.com/lists/musl/2019/01/21/8>
"This release makes improvements with respect to default thread stack
size, including increasing the default from 80k to 128k, increasing
the default guard size from 4k to 8k, and allowing the default to be
increased via ELF headers so that programs that need larger stacks can
be build without source-level changes, using just LDFLAGS.
Insufficient stack size for AIO threads on kernels that don't honor
the constant MINSIGSTKSZ is also fixed.

The glob core has been rewritten to fix inability to see past
searchable-but-unreadable path components, and to avoid excessive
stack usage and unnecessary syscalls. The tsearch AVL tree
implementation has also been rewritten for better size and
performance. The math library adds more native single-instruction
implementations for arm, s390x, powerpc, and x86_64.

Various bugs are fixed, including several possible deadlocks, one of
which was a new regression in 1.1.20."

detailed release notes can be found in the WHATSNEW file:
<http://git.musl-libc.org/cgit/musl/tree/WHATSNEW#n1989>

Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 months agoramips: dts: Unify naming of gpio-led nodes
Petr Štetiar [Sun, 30 Dec 2018 11:42:53 +0000 (12:42 +0100)]
ramips: dts: Unify naming of gpio-led nodes

In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2 months agoramips: dts: Unify naming of gpio-keys nodes
Petr Štetiar [Sun, 30 Dec 2018 11:17:25 +0000 (12:17 +0100)]
ramips: dts: Unify naming of gpio-keys nodes

In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2 months agoipq40xx: fix ASUS RT-AC58U switch port numbering
Christian Lamparter [Thu, 31 Jan 2019 21:29:32 +0000 (22:29 +0100)]
ipq40xx: fix ASUS RT-AC58U switch port numbering

This patch fixes the ASUS' RT-AC58U port order by
unifying the configuration with the NBG6617.

Reported-by: Roberto Socrates (rtac58u-user on the forum)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 months agoipq40xx: consolidate 02_network board defaults
Christian Lamparter [Thu, 31 Jan 2019 21:23:53 +0000 (22:23 +0100)]
ipq40xx: consolidate 02_network board defaults

This patch splits the big board case switch in 02_network in
two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs()
just like ath79 and ramips do.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 months agobrcm63xx: dts: Unify naming of gpio-led nodes
Petr Štetiar [Sun, 30 Dec 2018 11:42:53 +0000 (12:42 +0100)]
brcm63xx: dts: Unify naming of gpio-led nodes

In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2 months agobrcm63xx: dts: Unify naming of gpio-keys nodes
Petr Štetiar [Sun, 30 Dec 2018 11:17:25 +0000 (12:17 +0100)]
brcm63xx: dts: Unify naming of gpio-keys nodes

In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]