$(call Device/aruba_glenmorangie)
DEVICE_MODEL := AP-303H
endef
-# Missing DSA Setup
-#TARGET_DEVICES += aruba_ap-303h
+TARGET_DEVICES += aruba_ap-303h
define Device/aruba_ap-365
$(call Device/aruba_glenmorangie)
DEVICE_ALT0_VENDOR := AVM
DEVICE_ALT0_MODEL := FRITZ!Box 7520
SOC := qcom-ipq4019
- DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand
+ DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand ltq-vdsl-vr11-app
endef
TARGET_DEVICES += avm_fritzbox-7530
# Missing DSA Setup
#TARGET_DEVICES += glinet_gl-s1300
+define Device/kernel-size-6350-8300
+ DEVICE_COMPAT_VERSION := 2.0
+ DEVICE_COMPAT_MESSAGE := Kernel partition size must be increased for \
+ this OpenWrt version. Before continuing, you MUST issue either the \
+ command "fw_setenv kernsize 500000" from the OpenWrt command line, \
+ or "setenv kernsize 500000 ; saveenv" from the U-Boot serial console. \
+ Instead of the sysupgrade image, you must then install the OpenWrt \
+ factory image, setting the force flag and wiping the configuration. \
+ (e.g. "sysupgrade -n -F openwrt-squashfs-factory.bin" on command line)
+endef
+
define Device/linksys_ea6350v3
# The Linksys EA6350v3 has a uboot bootloader that does not
# support either booting lzma kernel images nor booting UBI
# partitions. This uboot, however, supports raw kernel images and
# gzipped images.
#
- # As for the time of writing this, the device will boot the kernel
- # from a fixed address with a fixed length of 3MiB. Also, the
- # device has a hard-coded kernel command line that requieres the
+ # As configured by the OEM factory, the device will boot the kernel
+ # from a fixed address with a fixed length of 3 MiB. Also, the
+ # device has a hard-coded kernel command line that requires the
# rootfs and alt_rootfs to be in mtd11 and mtd13 respectively.
# Oh... and the kernel partition overlaps with the rootfs
# partition (the same for alt_kernel and alt_rootfs).
#
# If you are planing re-partitioning the device, you may want to
- # keep those details in mind:
- # 1. The kernel adresses you should honor are 0x00000000 and
+ # keep these details in mind:
+ # 1. The kernel addresses you should honor are 0x00000000 and
# 0x02800000 respectively.
- # 2. The kernel size (plus the dtb) cannot exceed 3.00MiB in size.
+ # 2. The kernel size (plus the dtb) cannot exceed 3 MiB in size
+ # unless the uboot environment variable "kernsize" is increased.
# 3. You can use 'zImage', but not a raw 'Image' packed with lzma.
# 4. The kernel command line from uboot is harcoded to boot with
# rootfs either in mtd11 or mtd13.
$(call Device/FitzImage)
+ $(call Device/kernel-size-6350-8300)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA6350
DEVICE_VARIANT := v3
SOC := qcom-ipq4018
BLOCKSIZE := 128k
PAGESIZE := 2048
- KERNEL_SIZE := 3072k
- IMAGE_SIZE := 37888k
+ KERNEL_SIZE := 5120k
+ IMAGE_SIZE := 35840k
UBINIZE_OPTS := -E 5
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA6350v3
- DEFAULT := n
endef
TARGET_DEVICES += linksys_ea6350v3
define Device/linksys_ea8300
$(call Device/FitzImage)
+ $(call Device/kernel-size-6350-8300)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := EA8300
SOC := qcom-ipq4019
- KERNEL_SIZE := 3072k
- IMAGE_SIZE := 87040k
+ KERNEL_SIZE := 5120k
+ IMAGE_SIZE := 84992k
BLOCKSIZE := 128k
PAGESIZE := 2048
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=EA8300
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-linksys_ea8300 kmod-usb-ledtrig-usbport
- DEFAULT := n
endef
TARGET_DEVICES += linksys_ea8300
define Device/linksys_mr8300
$(call Device/FitzImage)
+ $(call Device/kernel-size-6350-8300)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := MR8300
SOC := qcom-ipq4019
- KERNEL_SIZE := 3072k
- IMAGE_SIZE := 87040k
+ KERNEL_SIZE := 5120k
+ IMAGE_SIZE := 84992k
BLOCKSIZE := 128k
PAGESIZE := 2048
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
IMAGES += factory.bin
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=MR8300
DEVICE_PACKAGES := ath10k-firmware-qca9888-ct kmod-usb-ledtrig-usbport
- DEFAULT := n
endef
TARGET_DEVICES += linksys_mr8300
-define Device/linksys_whw01-v1
+define Device/linksys_whw03v2
+ $(call Device/FitzImage)
+ DEVICE_VENDOR := Linksys
+ DEVICE_MODEL := WHW03
+ DEVICE_VARIANT := V2
+ SOC := qcom-ipq4019
+ KERNEL_SIZE := 6144k
+ IMAGE_SIZE := 158720k
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
+ IMAGES += factory.bin
+ IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=WHW03v2
+ DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-linksys_whw03v2 kmod-leds-pca963x kmod-spi-dev kmod-bluetooth
+endef
+TARGET_DEVICES += linksys_whw03v2
+
+define Device/linksys_whw01
$(call Device/FitzImage)
DEVICE_VENDOR := Linksys
DEVICE_MODEL := WHW01
- DEVICE_VARIANT := v1
KERNEL_SIZE := 6144k
- IMAGE_SIZE := 28704512 # 28032k minus linksys signature (256-bytes).
+ IMAGE_SIZE := 75776K
SOC := qcom-ipq4018
BLOCKSIZE := 128k
PAGESIZE := 2048
UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF
IMAGES += factory.bin
- IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \
- append-ubi | linksys-image type=WHW01 | pad-to $$$$(PAGESIZE) | \
- check-size
+ IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | linksys-image type=WHW01
DEVICE_PACKAGES := uboot-envtools kmod-leds-pca963x
endef
-# Missing DSA Setup
-#TARGET_DEVICES += linksys_whw01-v1
+TARGET_DEVICES += linksys_whw01
define Device/luma_wrtq-329acn
$(call Device/FitImage)
# Missing DSA Setup
#TARGET_DEVICES += unielec_u4019-32m
+define Device/zte_mf18a
+ $(call Device/FitImage)
+ DEVICE_VENDOR := ZTE
+ DEVICE_MODEL := MF18A
+ SOC := qcom-ipq4019
+ DEVICE_DTS_CONFIG := config@ap.dk04.1-c1
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ KERNEL_IN_UBI := 1
+ DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct ipq-wifi-zte_mf18a
+endef
+TARGET_DEVICES += zte_mf18a
+
define Device/zte_mf28x_common
$(call Device/FitzImage)
DEVICE_VENDOR := ZTE
projects / openwrt / staging / ldir.git / blobdiff