target/linux/ath79/dts/ar9330_gl_ar150.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "ar9330.dtsi"
   8
   9 / {
  10         model = "GL.iNet GL-AR150";
  11         compatible = "glinet,ar150";
  12
  13         aliases {
  14                 serial0 = &uart;
  15         };
  16
  17         memory@0 {
  18                 device_type = "memory";
  19                 reg = <0x0 0x4000000>;
  20         };
  21
  22         leds {
  23                 compatible = "gpio-leds";
  24
  25                 wlan {
  26                         label = "gl-ar150:orange:wlan";
  27                         gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
  28                         default-state = "off";
  29                 };
  30
  31                 lan {
  32                         label = "gl-ar150:green:lan";
  33                         gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
  34                         default-state = "off";
  35                 };
  36
  37                 wan {
  38                         label = "gl-ar150:green:wan";
  39                         gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
  40                         default-state = "off";
  41                 };
  42         };
  43
  44         keys {
  45                 compatible = "gpio-keys-polled";
  46                 #address-cells = <1>;
  47                 #size-cells = <0>;
  48                 poll-interval = <100>;
  49
  50                 manual {
  51                         label = "manual";
  52                         linux,code = <BTN_7>;
  53                         gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
  54                 };
  55
  56                 auto {
  57                         label = "auto";
  58                         linux,code = <BTN_8>;
  59                         gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
  60                 };
  61
  62                 reset {
  63                         label = "reset";
  64                         linux,code = <KEY_RESTART>;
  65                         gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
  66                 };
  67         };
  68 };
  69
  70 &uart {
  71         status = "okay";
  72 };
  73
  74 &gpio {
  75         status = "okay";
  76 };
  77
  78 &usb {
  79         dr_mode = "host";
  80         status = "okay";
  81 };
  82
  83 &usb_phy {
  84         status = "okay";
  85         gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
  86 };
  87
  88 &spi {
  89         num-chipselects = <1>;
  90         status = "okay";
  91
  92         spiflash {
  93                 #address-cells = <1>;
  94                 #size-cells = <1>;
  95                 compatible = "jedec,spi-nor";
  96                 spi-max-frequency = <104000000>;
  97                 reg = <0>;
  98
  99                 partition@0 {
 100                         label = "u-boot";
 101                         reg = <0x000000 0x040000>;
 102                         read-only;
 103                 };
 104
 105                 partition@1 {
 106                         label = "u-boot-env";
 107                         reg = <0x040000 0x010000>;
 108                 };
 109
 110                 partition@2 {
 111                         label = "firmware";
 112                         reg = <0x050000 0xfa0000>;
 113                 };
 114
 115                 art: partition@3 {
 116                         label = "ART";
 117                         reg = <0xff0000 0x010000>;
 118                         read-only;
 119                 };
 120         };
 121 };
 122
 123 &mdio0 {
 124         status = "okay";
 125
 126         phy4: ethernet-phy@4 {
 127                 reg = <4>;
 128                 phy-mode = "mii";
 129         };
 130 };
 131
 132 &eth0 {
 133         status = "okay";
 134
 135         mtd-mac-address = <&art 0x0>;
 136
 137         phy-handle = <&phy4>;
 138 };
 139
 140 &eth1 {
 141         status = "okay";
 142
 143         mtd-mac-address = <&art 0x0>;
 144
 145         fixed-link {
 146                 speed = <1000>;
 147                 full-duplex;
 148         };
 149
 150         gmac-config {
 151                 device = <&gmac>;
 152
 153                 switch-phy-addr-swap = <0>;
 154                 switch-phy-swap = <0>;
 155         };
 156 };