openwrt/staging/lynxis.git
5 months agoag71xx: Fix rx ring buffer stall on small packets flood on qca956x and qca953x.
Vittorio Gambaletta [Sat, 25 Mar 2017 17:08:02 +0000 (18:08 +0100)]
ag71xx: Fix rx ring buffer stall on small packets flood on qca956x and qca953x.

Backported from Code Aurora QSDK

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
5 months agobase-files: set FAILSAFE in /etc/profile when /tmp/.failsafe exists
Matthias Schiffer [Fri, 29 Dec 2017 13:34:03 +0000 (14:34 +0100)]
base-files: set FAILSAFE in /etc/profile when /tmp/.failsafe exists

Since dropbear clears the environment, FAILSAFE was not set as intended in
failsafe mode. This also broke sysupgrade from failsafe mode over SSH.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
5 months agobusybox: add missing TARGET_CPPFLAGS and TARGET_LDFLAGS
Matthias Schiffer [Sun, 10 Dec 2017 17:04:53 +0000 (18:04 +0100)]
busybox: add missing TARGET_CPPFLAGS and TARGET_LDFLAGS

Unconditionally pass TARGET_CPPFLAGS (not passed at all before) and
TARGET_LDFLAGS (passed only in certain non-default configuration before the
Makefile streamlining). Without these flags, hardening options
(PKG_FORTIFY_SOURCE and PKG_RELRO) were not actually applied to busybox.

The addition of these flags increases the size of the stripped busybox
binary by about 6KB (~4KB with fortify headers, ~2KB with "-znow -zrelro")
with the default hardening options PKG_FORTIFY_SOURCE_1 and PKG_RELRO_FULL.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
5 months agobusybox: streamline Makefile
Matthias Schiffer [Sun, 10 Dec 2017 17:01:42 +0000 (18:01 +0100)]
busybox: streamline Makefile

Use default Build/Install steps where possible. No binary change in default
configuration, so PKG_RELEASE is not incremented.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
5 months agoinclude/package.mk: remove old configured stamps before attempting configuration
Matthias Schiffer [Sun, 10 Dec 2017 14:30:30 +0000 (15:30 +0100)]
include/package.mk: remove old configured stamps before attempting configuration

Some packages, e.g. busybox, explicitly remove old .configured stamps
before attempting configuration, rather than after the actual configuration
step. This seems like a good idea, as there will be no stamp left if
configuration fails. Change generic rules to work like this, so package-
specific rules can be dropped.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
5 months agodnsmasq: send procd signal on service reload
Florian Eckert [Tue, 19 Dec 2017 15:11:58 +0000 (16:11 +0100)]
dnsmasq: send procd signal on service reload

Send a SIGHUP signal via procd to the dnsmasq service so the instance(s)
re-read(s) the /tmp/hosts/dhcp config.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
5 months agodnsmasq: rewrite config on host name modification
Florian Eckert [Tue, 19 Dec 2017 14:08:48 +0000 (15:08 +0100)]
dnsmasq: rewrite config on host name modification

If the hostname in /etc/config/system is modified the dnsmasq should also
get triggered to rewrite/reload the config.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
5 months agox86: add NVMe support for motherboards w/ M.2 slot
Philip Prindeville [Fri, 22 Dec 2017 04:10:03 +0000 (21:10 -0700)]
x86: add NVMe support for motherboards w/ M.2 slot

A lot of 1U x86_64 servers have NVMe support, which is lower-power
and higher speed than SSD or CFast drives, etc.  The drivers
required to make this work are trivial.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
5 months agokernel: bump 4.4 to 4.4.108
Kevin Darbyshire-Bryant [Tue, 26 Dec 2017 17:58:08 +0000 (17:58 +0000)]
kernel: bump 4.4 to 4.4.108

Refresh patches.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
5 months agokernel: bump 4.9 to 4.9.72
Kevin Darbyshire-Bryant [Mon, 25 Dec 2017 17:33:03 +0000 (17:33 +0000)]
kernel: bump 4.9 to 4.9.72

Refresh patches.

Runtime tested: ar71xx - Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
5 months agolayerscape: add byte_swap.py script for ls-rcw package
Yangbo Lu [Mon, 25 Dec 2017 06:38:11 +0000 (14:38 +0800)]
layerscape: add byte_swap.py script for ls-rcw package

This patch is to add a byte_swap.py script for rcw bin
byte swapping instead of using tclsh.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
5 months agolayerscape: fix PKG_BUILD_DIR for packages
Yangbo Lu [Mon, 25 Dec 2017 04:21:26 +0000 (12:21 +0800)]
layerscape: fix PKG_BUILD_DIR for packages

PKG_BUILD_DIR was defined with quoting PKG_VERSION in
layerscape package makefiles. Now PKG_VERSION has been
removed from these makefiles. When PKG_BUILD_DIR quotes
PKG_VERSION, '=' should be used instead ':=' to make
sure PKG_VERSION has been defined in common makefile.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
5 months agokernel: add i2c-smbus module package
Philip Prindeville [Tue, 17 Oct 2017 04:11:24 +0000 (22:11 -0600)]
kernel: add i2c-smbus module package

Intel motherboards (as well as the Cavium ThunderX SoC) use a
superset of the I2C protocol called SMBus.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
5 months agolinux: unbreak host tools build for 4.14
Jonas Gorski [Mon, 25 Dec 2017 18:04:35 +0000 (19:04 +0100)]
linux: unbreak host tools build for 4.14

Remove a stray -Wp left in host_c_flags causing build failures for newer
4.14 versions.

Reported-by: Michael Marley <michael@michaelmarley.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
5 months agobrcm2708: use x86's upgrade scripts for all rpi targets
Christian Lamparter [Sun, 17 Dec 2017 14:18:49 +0000 (15:18 +0100)]
brcm2708: use x86's upgrade scripts for all rpi targets

Advantages:
 - preserves existing partition layout on the sd-card.
   Only the boot and rootfs partition will be overwritten.

Please note that sysupgrade will refuse to upgrade, if the existing
installation  has an incompatible partition layout. Future changes
to the bootfs and/or rootfs partition size will likely cause breakage
to the sysupgrade procedure. In these cases, the ext4-sdcard.img.gz
will have to be written to the sdcard manually.
Please don't forget to backup your configuration in this case.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
5 months agobrcm2708: convert to dt-based board-detection
Christian Lamparter [Sun, 17 Dec 2017 14:18:48 +0000 (15:18 +0100)]
brcm2708: convert to dt-based board-detection

Use the values populated by the generic board detect function. The
first compatible from the device tree source file will be the board
name in userspace. The model property from the device tree source file
will be the model name.

Change the board name where used in the userspace and drop the target
specific board detect, to use the generic one.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
5 months agobrcm2708: add compatible strings
Christian Lamparter [Sun, 17 Dec 2017 14:18:47 +0000 (15:18 +0100)]
brcm2708: add compatible strings

This patch adds the compatible string for the various RPIs from
4.14 upstream.

Note: The 4.14 upstream does not include the compute modules.
If the CM* would just house the SoC, it could in theory use the
"raw" chip compatible string. However, these CM boards also come
with RAM and eMMC. So they have to have a proper comaptible.

For now, "raspberrypi,compute-module-{1|3}" will be good enough.

Note2: The original CM was renamed to CM1 when CM3 was released.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
5 months agobrcm2708: convert to metadata
Christian Lamparter [Sun, 17 Dec 2017 14:18:46 +0000 (15:18 +0100)]
brcm2708: convert to metadata

This patch converts all the raspberrypi images to utilize
the common metadata-based image verification.

Note: the CM1 and CM3 currently use the same "rpi-cm"
boardname.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
5 months agonghttp2: bump to 1.29.0
Hans Dedecker [Sun, 24 Dec 2017 16:01:35 +0000 (17:01 +0100)]
nghttp2: bump to 1.29.0

439b9b6c (tag: v1.29.0) Update manual pages
48498452 Bump up version number to v1.29.0, LT revision to 29:1:15
d30f3816 Update manual pages
4d1139f6 Remove SPDY
48f57407 nghttpx: Update doc
c1f14d73 Update manual pages
216f4dad nghttpx: Remove redundant check
a4e27d76 Revert "nghttpx: Use an existing h2 backend connection as much as possible"
2365f12e Fix CMAKE_MODULE_PATH
03f7ec0f nghttpx: Write API request body in temporary file
2056e812 nghttpx: Increase api-max-request-body
1ebb6810 nghttpx: Faster configuration loading with lots of backends
a3ebeeaf nghttpx: Fix crash with --backend-http-proxy-uri option
422ad1be Use NGHTTP2_REFUSED_STREAM for streams which are closed by GOAWAY
97f1735c Bump up version number to 1.29.0

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 months agousbmode: update to latest git HEAD
John Crispin [Tue, 19 Dec 2017 19:49:06 +0000 (20:49 +0100)]
usbmode: update to latest git HEAD

f40f84c support PantechMode
d8dc335 support Quanta and Blackberry modes
333e486 fix support for Option modems

Signed-off-by: John Crispin <john@phrozen.org>
5 months agoar71xx: spi-rb4xx: balance clk_prepare_enable() call
Gabor Juhos [Tue, 19 Dec 2017 07:24:38 +0000 (08:24 +0100)]
ar71xx: spi-rb4xx: balance clk_prepare_enable() call

Commit c312cef223dd ("ar71xx: spi-rb4xx fix.") replaced the clk_enable() call
with clk_prepare_enable() to meet the common clock framework requirements.
However it did not change the clk_disable() call in the error patch which
thus leads to imbalance.

Fix the code by using the correct counterpart of clk_prepare_enable() in both
places.

Fixes: c312cef223dd ("ar71xx: spi-rb4xx fix.")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
5 months agokernel/4.14: add missing newline character to UBI messages
Gabor Juhos [Tue, 19 Dec 2017 08:11:57 +0000 (09:11 +0100)]
kernel/4.14: add missing newline character to UBI messages

A few UBI messages lacks the trailing newline character which
leads to ugly lines in the bootlog like this:

  [    6.649159] UBI error: no valid UBI magic found inside mtd6[    6.667751] Freeing unused kernel memory: 2196K

Add a newline character to the end of the messages to fix it.
After the fix the line from above looks better in the log:

  [    6.609182] UBI error: no valid UBI magic found inside mtd6
  [    6.627599] Freeing unused kernel memory: 2132K

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
5 months agokernel/4.9: add missing newline character to UBI messages
Gabor Juhos [Tue, 19 Dec 2017 08:11:48 +0000 (09:11 +0100)]
kernel/4.9: add missing newline character to UBI messages

A few UBI messages lacks the trailing newline character which
leads to ugly lines in the bootlog like this:

  [    6.649159] UBI error: no valid UBI magic found inside mtd6[    6.667751] Freeing unused kernel memory: 2196K

Add a newline character to the end of the messages to fix it.
After the fix the line from above looks better in the log:

  [    6.609182] UBI error: no valid UBI magic found inside mtd6
  [    6.627599] Freeing unused kernel memory: 2132K

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
5 months agokernel/4.4: add missing newline character to UBI messages
Gabor Juhos [Tue, 19 Dec 2017 08:11:24 +0000 (09:11 +0100)]
kernel/4.4: add missing newline character to UBI messages

A few UBI messages lacks the trailing newline character which
leads to ugly lines in the bootlog like this:

  [    6.649159] UBI error: no valid UBI magic found inside mtd6[    6.667751] Freeing unused kernel memory: 2196K

Add a newline character to the end of the messages to fix it.
After the fix the line from above looks better in the log:

  [    6.609182] UBI error: no valid UBI magic found inside mtd6
  [    6.627599] Freeing unused kernel memory: 2132K

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
5 months agowireguard: bump to 20171221
Kevin Darbyshire-Bryant [Sat, 23 Dec 2017 19:26:52 +0000 (19:26 +0000)]
wireguard: bump to 20171221

7e945a8 version: bump snapshot
f2168aa compat: kernels < 3.13 modified genl_ops
52004fd crypto: compile on UML
6b69b65 wg-quick: dumber matching for default routes
aa35d9d wg-quick: add the "Table" config option
037c389 keygen-html: remove prebuilt file

No patch refresh required.

Compile-test-for: ar71xx
Run-tested-on: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
5 months agokernel: bump 4.4 to 4.4.107
Kevin Darbyshire-Bryant [Thu, 21 Dec 2017 19:12:27 +0000 (19:12 +0000)]
kernel: bump 4.4 to 4.4.107

Refresh patches.

Update patch that no longer applied:
oxnas/0072-mtd-backport-v4.7-0day-patches-from-Boris.patch

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Rosen Penev <rosenp@gmail.com>
5 months agolantiq: remove DSL_ChipSetHWVersion from status information
Martin Schiller [Fri, 22 Dec 2017 07:42:18 +0000 (08:42 +0100)]
lantiq: remove DSL_ChipSetHWVersion from status information

The value DSL_ChipSetHWVersion is fetched from the dsl frontend
via the dsl_control service, but not really provided by the dsl
frontend firmware and for now always "UNKNOWN".

The lantiq support told us that this information wouldn't be
provided in the foreseeable future, so let's remove this
useless "UNKNOWN" information.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
5 months agoramips: fix Linkit smart 7688 support
Mathias Kresin [Thu, 21 Dec 2017 18:55:25 +0000 (19:55 +0100)]
ramips: fix Linkit smart 7688 support

Use a more appropriate compatible string. Fix the wireless led GPIO and
add the default wireless trigger. Use the wireless LED for boot state
indication as well.

Remove the GPIO pinmux for pins not exposed on the board.

Signed-off-by: Mathias Kresin <dev@kresin.me>
5 months agoramips: add support for TP-Link TL-MR3420 v5
Henryk Heisig [Fri, 15 Dec 2017 14:57:49 +0000 (15:57 +0100)]
ramips: add support for TP-Link TL-MR3420 v5

TP-Link TL-MR3420 v5 are simple N300 router with
5-port FE switch and non-detachable antennas.
Its very similar to TP-Link TL-WR841N V13.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 8x LED, 2x button, power input switch

Flash instruction:

The only way to flash LEDE image in mr3420v5 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-mr3420-v5-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
5 months agoramips: move common tplink image build code into own recipe
Mathias Kresin [Sun, 17 Dec 2017 09:44:41 +0000 (10:44 +0100)]
ramips: move common tplink image build code into own recipe

Move common tplink image build code into own recipe. Include the common
parts instead of including a full build recipe and overwriting former set
varaibles.

Signed-off-by: Mathias Kresin <dev@kresin.me>
5 months agokernel: move console loglevel to generic
Tomasz Maciej Nowak [Wed, 20 Dec 2017 18:55:16 +0000 (19:55 +0100)]
kernel: move console loglevel to generic

Move CONFIG_CONSOLE_LOGLEVEL_DEFAULT=7 to generic, to make it consistent
across all targets.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
5 months agouci: update to latest git HEAD (FS#1182)
Hans Dedecker [Fri, 22 Dec 2017 17:16:41 +0000 (18:16 +0100)]
uci: update to latest git HEAD (FS#1182)

25fd142 list: remove unncessary increment of n_section (FS#1182)
021fd65 file: remove unnecessary uci_fixup_section calls

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 months agoodhcpd: update to latest git HEAD
Hans Dedecker [Fri, 22 Dec 2017 17:11:20 +0000 (18:11 +0100)]
odhcpd: update to latest git HEAD

7aa2594 odhcpd: Replace strerror(errno) with %m format
750e457 Support muliple RAs on single interface

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5 months agokernel: add missing config symbols for 4.14
Stijn Tintel [Thu, 21 Dec 2017 22:54:41 +0000 (23:54 +0100)]
kernel: add missing config symbols for 4.14

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
6 months agoar71xx: add support for MikroTik RouterBOARD 921GS-5HPacD r2 (mANTBox 15s)
Roger Pueyo Centelles [Thu, 21 Dec 2017 14:53:05 +0000 (15:53 +0100)]
ar71xx: add support for MikroTik RouterBOARD 921GS-5HPacD r2 (mANTBox 15s)

This patch adds support for the MikroTik RouterBOARD 921GS-5HPacD r2
(mANTBox 15s), an outdoor sector antenna with a built-in 802.11ac
wireless router. Additionally, it adds a new profile for devices with
>= 128 MB NAND flash and 802.11ac to the ar71xx/mikrotik subtarget.

See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9558 (720 MHz)
 - RAM: 128 MB
 - Storage: 128 MB NAND
 - Wireless: external QCA9822 802.11a/ac 2x2:2
 - Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
 - SFP: 1x host

Working:
 - Board/system detection
 - NAND storage detection
 - Wireless
 - Ethernet
 - 1x user LED
 - Reset button
 - Sysupgrade

Untested:
 - SFP cage (probably not working)

Installation:
 - Boot initramfs image via TFTP and then flash sysupgrade image

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
6 months agoar71xx: fix spelling in mach-rb922.c
Roger Pueyo Centelles [Thu, 21 Dec 2017 14:52:38 +0000 (15:52 +0100)]
ar71xx: fix spelling in mach-rb922.c

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
6 months agoar71xx: fix rb922gs_nand_scan_fixup()
Roger Pueyo Centelles [Thu, 21 Dec 2017 14:51:10 +0000 (15:51 +0100)]
ar71xx: fix rb922gs_nand_scan_fixup()

Apply code from commits 9e1bc27e6d67fa29791eb0fac5e5f0066d12a761
(ar71xx: Fix UBIFS work on Mikrotik RB95x devices) and
665bb2749906aff4d4ec607a308353fa30cb1b3a (ar71xx: fix invalid pointer
dereference in rb95x_nand_scan_fixup()) to RB92x devices too.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
6 months agolayerscape: fix package download
Hauke Mehrtens [Thu, 21 Dec 2017 08:32:51 +0000 (09:32 +0100)]
layerscape: fix package download

The git hash was changed for multiple layerscape packages without
changing the version number. The LEDE build system will not download the
packages again if the old version is already there and so some people
and the build bots are using wrong version of some packages. Use
PKG_SOURCE_DATE instead of PKG_VERSION to generate packages with the
date and the first charterers of the git hash. This will change the file
name and make the build system download them again, also if in future
the git hash is changed the file name will change and trigger a new
download.

This should fix a problem spotted by build bot.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agoapm821xx: convert to device-tree board detection
Christian Lamparter [Sun, 17 Dec 2017 14:00:01 +0000 (15:00 +0100)]
apm821xx: convert to device-tree board detection

This patch converts all apm821xx devices to the device-tree
board-detection method. All instances of the legacy
boardnames (mbl,mr24,...) are converted to "vendor,device"
identifier.

The custom board-detection code in apm821xx.sh is removed as
it no longer serves any purpose.

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
6 months agoapm821xx: enable metadata for packaging
Christian Lamparter [Sun, 17 Dec 2017 14:00:00 +0000 (15:00 +0100)]
apm821xx: enable metadata for packaging

This patch enables metadata-supported image verification
for all apm821xx supported devices. Since this method comes
with a built-in image verification tool (fwtool), the previous
image checks can be removed.

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
6 months agoapm821xx: align device names with vendor_device format
Christian Lamparter [Sun, 17 Dec 2017 13:59:59 +0000 (14:59 +0100)]
apm821xx: align device names with vendor_device format

Currently, the device name handle does not include the
manufacturer. This can make it hard do differentiate
between products from different vendors that have the
same product name. As the handle is used to derive
the image name.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
6 months agoapm821xx: dts: rename devices dts files to include the manufacturer
Christian Lamparter [Sun, 17 Dec 2017 13:59:58 +0000 (14:59 +0100)]
apm821xx: dts: rename devices dts files to include the manufacturer

This patch rename all the DT source files in order to
match upstream's "manufacturer-device.dts" format.

Please note that the DEVICE_DTB isn't changed. This is
because the u-boot of the MyBook Live defines the
fdt_file variable to be "apollo3g/apollo3g.dtb".

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
6 months agoapm821xx: add product names to the dt compatible for Meraki
Christian Lamparter [Sun, 17 Dec 2017 13:59:57 +0000 (14:59 +0100)]
apm821xx: add product names to the dt compatible for Meraki

Meraki choose to use their product's codename as the main
compatible string. Mathias Kresin commented that this is
a poor choice as this will confuse the users and devs once
the device-tree compatible is used for board-detection and
possible the image name.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
6 months agoapm821xx: dts: append SoC compatible to DTS
Christian Lamparter [Sun, 17 Dec 2017 13:59:56 +0000 (14:59 +0100)]
apm821xx: dts: append SoC compatible to DTS

This patch appends the "apm,bluestone" or "amcc,apollo3g"
machine compatible string to the current device tree source.

Please note that unlike other archs the PPC DT code does
not regard the machine's compatible string as a priority
list. This is explained in the kernel's usage-model.txt as follows:
"PowerPC uses a slightly different scheme where it calls the .probe()
hook from each machine_desc, and the first one returning TRUE is used.
However, this approach does not take into account the priority of the
compatible list, and probably should be avoided for new architecture
support."

For this reason, the "apm,bluestone" compatible string can't be
added to the WNDR4700. As otherwise the target specific pci
fix-up code will get ignored and this causes the ath9k WIFI
to not get initialized.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
6 months agoapm821xx: replace DEVICE_{PROFILE|NAME} with BOARD_NAME
Christian Lamparter [Sun, 17 Dec 2017 13:59:55 +0000 (14:59 +0100)]
apm821xx: replace DEVICE_{PROFILE|NAME} with BOARD_NAME

This patch sets the BOARD_NAME variable on each affected
apm821xx device. The existing DEVICE_PROFILE and
DEVICE_NAME assignments are deprecated as they no longer
serve any purpose.

The BOARD_NAME variable is used by the sysupgrade-tar
method to specifiy a directory overwrite for the
sysupgrade-$dir directory in the generated tar file.
Keeping the original boardname in this context will be
necessary for targets that utilize the sysupgrade-tar
method. Otherwise, sysupgrade on an previous installation
will not recognize the newly generated images.

This step is necessary since an upcoming patch realigns
the existing shortname for a device with a proper
"manufacturer_device" identifier.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
6 months agoapm821xx: replace whitespace with tabs
Christian Lamparter [Sun, 17 Dec 2017 13:59:54 +0000 (14:59 +0100)]
apm821xx: replace whitespace with tabs

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
6 months agoapm821xx: explicitly build the rootfs.img.gz target
Christian Lamparter [Sun, 17 Dec 2017 13:59:53 +0000 (14:59 +0100)]
apm821xx: explicitly build the rootfs.img.gz target

The commit 87b668765e1
("image: when using the new image build code, gzip ext4 images by default")

forced that all targets that select the ext4 as the root filesystem
to always compress the generated rootfs. This is fine, but this method
doesn't not allow to append the metadata on a per-target base.

Therefore this patch changes the rootfs image production rule to generate
the gzip step manually. This way the metadata can be appended at a later
date.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
6 months agoramips: fix devicetree compat strings
Mathias Kresin [Tue, 19 Dec 2017 20:55:42 +0000 (21:55 +0100)]
ramips: fix devicetree compat strings

"PandoraBox" is not the name of the manufacturer, it's a firmware made by
the manufacturer actually. Their official English name is "D-Team".

PBR-M1 is the only one they use "PandoraBox" as a brand name. Their other
products are using "Newifi" as their trademark (including Y1 and Y1S which
used to be OEM products for Lenovo).

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
6 months agoramips: add support for newifi d2
Jackson Ming Hu [Fri, 15 Dec 2017 03:51:33 +0000 (11:51 +0800)]
ramips: add support for newifi d2

Previously Newifi D2 could only use PandoraBox M1's firmware.
It works fine, but LED GPIO is different.
As a result, a separated DTS file for this device should be implemented.

Hardware spec:

* CPU: MTK MT7621A
* RAM: 512MB
* ROM: 32MB SPI Flash
* WiFi: MTK MT7603+MT7612
* Button: 2 buttons (reset, wps)
* LED: 3 single-color LEDs (USB, WiFi 2.4GHz, WiFi 5GHz) &
       2 dual-color LEDs (Power, Internet)
* Ethernet: 5 ports, 4 LAN + 1 WAN

Installation method:

Same as Newifi D1, users may need to request unlock code from the device
manufacturer. Otherwise, a SPI flash programmer may be necessary to get
the firmware flashed. After the device is unlocked, press and hold reset
button before power cable plugs in. Then go to http://192.168.1.1 to
upload and flash the firmware package.

Signed-off-by: Jackson Ming Hu <huming2207@gmail.com>
6 months agoramips: add support for Vonets VAR11N-300
Andrew Crawley [Thu, 23 Nov 2017 23:52:13 +0000 (23:52 +0000)]
ramips: add support for Vonets VAR11N-300

The VAR11N-300 is a tiny wireless-N device with a hardwired Ethernet
cable, one extra Ethernet port, and an internal antenna, based on the
MediaTek MT7620n chipset.

Specs:
- MT7620n WiSoC @ 600MHz
- 32 MB SDRAM
- 4 MB SPI flash
- 2T2R 2.4GHz WiFi-N
- 1 attached 10/100 Ethernet cable (LAN)
- 1 10/100 Ethernet port (WAN)
- 1 attached USB / barrel 5vdc power cable
- 5 LEDs (see notes below)
- 1 reset button
- 1 UART (3 pads on board)

Installation:

The stock firmware does not support uploading new firmware directly,
only checking the manufacturer's site for updates.  This process may be
possible to spoof, but the update check uses some kind of homebrew
encryption that I didn't investigate.  Instead, you can install via a
backdoor:

1. Set up a TFTP server to serve the firmware binary
(lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin)
2. Factory reset the device by holding the reset button for a few
seconds.
3. Open the web interface (default IP: 192.168.253.254)
4. Log in with the "super admin" credentials: username `vonets`,
password `vonets26642519`.
5. On the "Operative Status" page, click the text "System Uptime", then
quickly click the uptime value.
6. If successful, an alert dialog will appear reading "Ated start", and
the device will now accept telnet connections.  If the alert does not
appear, repeat step 5 until it works (the timing is a bit tricky).
7. Telnet to the device using credentials "admin / admin"
8. Retrieve the firmware binary from the tftp server: `tftp -l lede.bin
-r lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin -g
<tftp-server-ip>`
9. Write the firmware to flash: `mtd_write write lede.bin /dev/mtd4`
10. Reboot

Tested:
- LAN / WAN ethernet
- WiFi
- LAN / WAN / status LED GPIOs (see notes below)
- Reset button
- Sysupgrade

Notes:

LEDs:

The board has 5 LEDs - two green LEDs for LAN / WAN activity, one blue
LED for WiFi, and a pair of "status" LEDs connected to the same GPIO
(the blue LED lights when the GPIO is low, and the green when it's
high).  I was unable to determine how to operate the WiFi LED, as it
does not appear to be controlled by a GPIO directly.

Recovery:

The default U-boot installation will only boot from flash due to a
missing environment block.  I generated a valid 4KB env block using
U-boot's `fw_setenv` tool and wrote it to flash at 0x30000 using an
external programmer.  After this, it was possible to enter the U-boot
commandline interface and download a new image via TFTP (`tftpboot
81b00000 <image-filename>`), but while I could boot this image
sucessfully (`bootm`), writing it to flash (`cp.linux`) just corrupted
the flash chip.  The sysupgrade file can be written to flash at 0x50000
using an external programmer.

Signed-off-by: Andrew Crawley <acrawley@gmail.com>
6 months agoramips: add helper variable for boardname
Mathias Kresin [Thu, 16 Nov 2017 21:17:42 +0000 (22:17 +0100)]
ramips: add helper variable for boardname

Add a helper variable which contains the boardname separated from the
vendor name. It allows to switch to a device tree compatible string
based boardname, by keeping the $board:colour:function syntax in
scripts handling/adding config for LEDs.

Boards not using the device tree compatible string as based boardname
are unaffected by the change, since none of them uses a comma in the
boardname.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 months agoramips: sync image filename with boardname
Mathias Kresin [Sat, 16 Dec 2017 23:30:21 +0000 (00:30 +0100)]
ramips: sync image filename with boardname

Use <manufacturer>_<modelname> as image name for board using the
devicetree compat string as boardname.

Replace the underline of the device define, to keep the SUPPORTED_DEVICES
in sync with a devicetree compat string based boardname.

Override the default SUPPORTED_DEVICES for board which are having an
userspace boardname with an underline.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 months agoramips: fallback to generic board detect
Mathias Kresin [Fri, 1 Dec 2017 07:10:24 +0000 (08:10 +0100)]
ramips: fallback to generic board detect

Fallback to the generic board detection if no case for the current
board exists.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 months agoramips: drop LinkIt Smart 7688 Duo userspace support
Mathias Kresin [Thu, 16 Nov 2017 21:58:23 +0000 (22:58 +0100)]
ramips: drop LinkIt Smart 7688 Duo userspace support

The  LinkIt Smart 7688/LinkIt Smart 7688 Duo are identical beside the
extra ATmega32U4 - accessible via UART - on the the Duo.

Since all relevant hardware is identical, drop the Duo special handling
in userspace.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 months agouboot-layerscape-armv8_32b: fix package download
Hauke Mehrtens [Wed, 20 Dec 2017 20:54:18 +0000 (21:54 +0100)]
uboot-layerscape-armv8_32b: fix package download

In commit 2b1ec44dbd3cd3 ("layerscape: add ls1012afrdm device support")
The git revision and the mirror hash for this package was updated to a
version which includes ls1012afrdm-uboot.bin, but the file name at
dl/uboot-layerscape-armv8_32b-2017.09.tar.xz staid the same. This way
most user did not download the new version but used the old file.
Convert this package to the normal git clone parameters by using
PKG_SOURCE_DATE instated of PKG_VERSION, now the file name in dl also
contains the git hash and should change every time the git hash is
updated.

This should fix a problem spotted by build bot.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: kmod-crypto-hw-talitos: fix dependencies
Hauke Mehrtens [Wed, 20 Dec 2017 19:46:21 +0000 (20:46 +0100)]
kernel: kmod-crypto-hw-talitos: fix dependencies

With the updated to kernel 4.9.70 in commit f704b643b9cab ("kernel:
Update kernel 4.9 to 4.9.70"), the talitos.ko kernel module got a
new dependency to kmod-crypto-des in this upstream commit:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable.git/commit/?id=552f74cbd6ec806ab5ce45336a26cae1e015dbe2

This fixes a build problem found by built bot.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: Update kernel 4.9 to 4.9.70
Hauke Mehrtens [Sat, 16 Dec 2017 20:09:41 +0000 (21:09 +0100)]
kernel: Update kernel 4.9 to 4.9.70

Runtime tested on lantiq.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agolibiconv-full: fix compile-time linking error GCC7
Jake Staehle [Tue, 24 Oct 2017 18:09:37 +0000 (13:09 -0500)]
libiconv-full: fix compile-time linking error GCC7

LEDE Flyspray Task 1091:
Fix libiconv-full 'undefined reference' compile linker error using GCC7 Musl
Tested with targets x86 (i386 and x86_64)
Addition of CFLAGS "std=gnu89" fixes the linker issues, credit to harrylwc
Issue found with 'minidlna' package, which depends on 'libiconv-full'
Error in compile log:
../lib/.libs/libiconv.so: undefined reference to `aliases_lookup'
../lib/.libs/libiconv.so: undefined reference to `aliases2_lookup'
collect2: error: ld returned 1 exit status
Makefile:64: recipe for target 'iconv_no_i18n' failed

Signed-off-by: Jake Staehle <jacob@staehle.us>
6 months agoramips: fix polarity in gpio-export node
Mathias Kresin [Sat, 16 Dec 2017 23:02:06 +0000 (00:02 +0100)]
ramips: fix polarity in gpio-export node

If we need to set the initial output value to GPIOF_OUT_INIT_HIGH (1) to
enable something, the pin is ACTIVE_HIGH. The same applies to
GPIOF_OUT_INIT_LOW (0) and ACTIVE_LOW.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 months agoar71xx: fix lan ports on ens202ext
Marty E. Plummer [Thu, 23 Nov 2017 20:36:28 +0000 (14:36 -0600)]
ar71xx: fix lan ports on ens202ext

In the stock firmware both eth0 and eth1 are set to br-lan,
add this behavior to our images.

Fixes: FS#1084

Signed-off-by: Marty E. Plummer <hanetzer@protonmail.com>
6 months agobrcm63xx: fix Sercomm AD1018 status led
Jonas Gorski [Sun, 17 Dec 2017 10:52:52 +0000 (11:52 +0100)]
brcm63xx: fix Sercomm AD1018 status led

The status led part was missed when changing the board name to *-nor.

Fixes: e12c72bb52eb ("brcm63xx: Add Sercomm AD1018 support")
Reported-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
6 months agomt76: update to the latest version, reverts MAC address changes causing performance...
Felix Fietkau [Sun, 17 Dec 2017 11:41:58 +0000 (12:41 +0100)]
mt76: update to the latest version, reverts MAC address changes causing performance regressions

cf4a5ce mt76: fix memcpy to potential null pointer on failed allocation
ca5ca8c mt76x2: fix possible NULL pointer dereferencing in mt76x2_ampdu_action()
2d4b8f5 mt76x2: mac: fix possible NULL pointer dereferencing in mt76x2_mac_write_txwi()
4ca8bba mt76x2: eeprom: fix typo in mt76x2_get_power_info_5g()
00f7e60 mt7603: fix configuration for HT40
31e9bdb mt7603: main: fix possible NULL pointer dereferencing in mt7603_ampdu_action()
bf90dd2 mt7603: mcu: fix potential NULL pointer dereferencing on failed allocation
860b185 Revert "mt76x2: init: disable APCLI by default"
bcd576e Revert "mt76x2: drop wiphy->addresses"
bdc6f2f Revert "mt76x2: clean up MAC/BSSID address initialization"
d242650 Revert "mt76x2: remove MAC address limitation for multi-vif setups"
68b0cf1 mt76x2: add functions for setting extended MAC address registers

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 months agolantiq: sync image filename with boardname
Mathias Kresin [Fri, 8 Dec 2017 07:42:11 +0000 (08:42 +0100)]
lantiq: sync image filename with boardname

Use <manufacturer>_<modelname> as image name.

Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.

While at it, normalise the image filenames by using only lower case
characters and bin as file extension for sysupgrade images.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 months agolantiq: drop unused variable from image build code
Mathias Kresin [Fri, 8 Dec 2017 07:07:50 +0000 (08:07 +0100)]
lantiq: drop unused variable from image build code

Remove the DEVICE_PROFILE variable. The variable isn't
used at all.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 months agolantiq: use the generic board detect
Mathias Kresin [Sat, 8 Apr 2017 09:59:24 +0000 (11:59 +0200)]
lantiq: use the generic board detect

Drop the target specific detection function in favour of the generic
one provided by base-files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 months agolantiq: add missing model names
Mathias Kresin [Sat, 8 Apr 2017 09:47:44 +0000 (11:47 +0200)]
lantiq: add missing model names

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 months agolantiq: remove the former board name from device tree model
Mathias Kresin [Sat, 8 Apr 2017 09:40:07 +0000 (11:40 +0200)]
lantiq: remove the former board name from device tree model

Remove the former used board name from the device model property and
use the model name as it is.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 months agolantiq: use the compatible string as board name
Mathias Kresin [Sat, 8 Apr 2017 09:16:21 +0000 (11:16 +0200)]
lantiq: use the compatible string as board name

Use the first compatible string as board name in userspace. Add the new
board name as well as the former used board name to the image metadata
to keep compatibilty with already deployed installations.

Don't add the former used boardname for boards which exists only in
master or evaluation boards.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 months agolantiq: drop SoC name from eval boards compatible string
Mathias Kresin [Sat, 8 Apr 2017 08:59:32 +0000 (10:59 +0200)]
lantiq: drop SoC name from eval boards compatible string

Keep it in the same format as used for the other eval boards.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 months agolantiq: add compatible strings to dts files
Mathias Kresin [Sat, 8 Apr 2017 08:33:53 +0000 (10:33 +0200)]
lantiq: add compatible strings to dts files

The compatible string is mandetory for devicetree source file.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 months agox86: Add support for kernel 4.14
Hauke Mehrtens [Sun, 29 Oct 2017 18:34:13 +0000 (19:34 +0100)]
x86: Add support for kernel 4.14

This adds basic support for kernel 4.14, this was tested in qemu only.
The subtarget configuration was refresh with kernel 4.14 and the
options needed to make it compile on kernel 4.9 were added manually.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: include: remove last .0 from kernel versions again
Hauke Mehrtens [Fri, 17 Nov 2017 21:55:03 +0000 (22:55 +0100)]
kernel: include: remove last .0 from kernel versions again

Kernel 4.14 has the version number 4.14 and not 4.14.0. This was
different in some older Linux kernel versions, This change makes it
possible to use kernel 4.14 without any minor version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: add missing dependencies to kmod-crypto-acompress
Hauke Mehrtens [Sat, 25 Nov 2017 23:24:28 +0000 (00:24 +0100)]
kernel: add missing dependencies to kmod-crypto-acompress

kmod-lib-lzo and kmod-lib-lz4 depend in kernel 4.14 on
kmod-crypto-acompress, add this missing dependency.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: kmod-rtc-ds1307: add dependency to regmap
Hauke Mehrtens [Sat, 25 Nov 2017 21:05:21 +0000 (22:05 +0100)]
kernel: kmod-rtc-ds1307: add dependency to regmap

In kernel 4.14 kmod-rtc-ds1307 depends on regmap-i2c, add this missing
dependency.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: kmod-iio-bmp280: allow compile with kernel 4.14
Hauke Mehrtens [Mon, 13 Nov 2017 21:19:43 +0000 (22:19 +0100)]
kernel: kmod-iio-bmp280: allow compile with kernel 4.14

This package also compiles with kernel 4.14.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: kmod-zram: deactivate CONFIG_ZRAM_WRITEBACK for kernel 4.14
Hauke Mehrtens [Sun, 12 Nov 2017 21:22:07 +0000 (22:22 +0100)]
kernel: kmod-zram: deactivate CONFIG_ZRAM_WRITEBACK for kernel 4.14

This new option was introduced in kernel 4.14 and should be deactivated
by default.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agoxtables-addons: fix compile with kernel 4.14
Hauke Mehrtens [Sun, 12 Nov 2017 21:20:22 +0000 (22:20 +0100)]
xtables-addons: fix compile with kernel 4.14

This fixes a compile problems seen with kernel 4.14.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: kmod-fbcon: deactivate for kernel 4.14
Hauke Mehrtens [Wed, 29 Nov 2017 21:51:55 +0000 (22:51 +0100)]
kernel: kmod-fbcon: deactivate for kernel 4.14

CONFIG_FRAMEBUFFER_CONSOLE does not activate new modules any more in
kernel 4.14, but CONFIG_FRAMEBUFFER_CONSOLE is now a boolean option
which change the kmod-fb package. kmod-fbcon should be split up.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: kmod-sound-core: handle moved snd-seq-device.ko
Hauke Mehrtens [Sun, 12 Nov 2017 21:17:30 +0000 (22:17 +0100)]
kernel: kmod-sound-core: handle moved snd-seq-device.ko

The snd-seq-device.ko kernel module was moved with kernel 4.13.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: kmod-mmc: handle moved mmc_block.ko
Hauke Mehrtens [Sun, 12 Nov 2017 21:16:46 +0000 (22:16 +0100)]
kernel: kmod-mmc: handle moved mmc_block.ko

mmc_block.ko was moved with kernel 4.10.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: kmod-rxrpc: handle renamed kernel module
Hauke Mehrtens [Sun, 12 Nov 2017 21:15:14 +0000 (22:15 +0100)]
kernel: kmod-rxrpc: handle renamed kernel module

The kernel module was renamed with kernel 4.11, handle that in the
package definition.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: deactivate some new network features
Hauke Mehrtens [Sun, 12 Nov 2017 21:13:23 +0000 (22:13 +0100)]
kernel: deactivate some new network features

This deactivates the following options which were introduced between
kernel 4.9 and 4.14 in some kernel packages:
CONFIG_INET_ESP_OFFLOAD
CONFIG_INET6_ESP_OFFLOAD
CONFIG_LWTUNNEL_BPF
CONFIG_NET_9P_XEN

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: unset CONFIG_CIFS_SMB311 in kmod-fs-cifs
Hauke Mehrtens [Sun, 12 Nov 2017 21:08:28 +0000 (22:08 +0100)]
kernel: unset CONFIG_CIFS_SMB311 in kmod-fs-cifs

Do not activate the experimental feature CONFIG_CIFS_SMB311.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: add kmod-crypto-ecdh
Hauke Mehrtens [Sun, 12 Nov 2017 21:06:38 +0000 (22:06 +0100)]
kernel: add kmod-crypto-ecdh

In kernel 4.14 kmod-bluetooth depends on kmod-crypto-ecdh, add
kmod-crypto-ecdh to LEDE.
Both packages also depend on the kmod-crypto-kpp package. To build this
we have to fix the dependency of CRYPTO_ECDH which has a typo.
This patch is already accepted upstream.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: add kmod-crypto-rsa
Hauke Mehrtens [Sun, 12 Nov 2017 21:04:17 +0000 (22:04 +0100)]
kernel: add kmod-crypto-rsa

In kernel 4.14 kmod-crypto-hw-ccp depends on kmod-crypto-rsa, add it.
kmod-crypto-rsa also packages the ASN1 parser and some other code which
is currently only used by this module.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: add kmod-crypto-acompress
Hauke Mehrtens [Sun, 12 Nov 2017 21:02:27 +0000 (22:02 +0100)]
kernel: add kmod-crypto-acompress

In kernel 4.14 kmod-crypto-deflate depends on kmod-crypto-acompress.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: add kmod-lib-zstd
Hauke Mehrtens [Sun, 12 Nov 2017 21:00:20 +0000 (22:00 +0100)]
kernel: add kmod-lib-zstd

In kernel 4.14 kmod-fs-btrfs depends on the zstd compression libraries,
add it to the package system.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: add kmod-dax
Hauke Mehrtens [Sun, 12 Nov 2017 20:58:19 +0000 (21:58 +0100)]
kernel: add kmod-dax

In kernel 4.14 kmod-dm depends on kmod-dax.
Add DAX: "Direct access to differentiated memory" to LEDE.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: tg3: deactivate hwmon for kernel 4.14
Hauke Mehrtens [Sun, 12 Nov 2017 14:34:05 +0000 (15:34 +0100)]
kernel: tg3: deactivate hwmon for kernel 4.14

In kernel 4.14 hwmon support can be deactivated for the tg3 driver,
deactivate it by default to save some space.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: generic: Add kernel 4.14 support
Hauke Mehrtens [Sun, 29 Oct 2017 18:32:10 +0000 (19:32 +0100)]
kernel: generic: Add kernel 4.14 support

This adds initial support for kernel 4.14 based on the patches for
kernel 4.9.

In the configuration I deactivated some of the new possible security
features like:
CONFIG_REFCOUNT_FULL
CONFIG_SLAB_FREELIST_HARDENED
CONFIG_SOFTLOCKUP_DETECTOR
CONFIG_WARN_ALL_UNSEEDED_RANDOM

And these overlay FS options are also deactivated:
CONFIG_OVERLAY_FS_INDEX
CONFIG_OVERLAY_FS_REDIRECT_DIR

I activated this:
CONFIG_FORTIFY_SOURCE
CONFIG_POSIX_TIMERS
CONFIG_SLAB_MERGE_DEFAULT
CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED

I am not sure if I did the porting correct for the following patches:
target/linux/generic/backport-4.14/020-backport_netfilter_rtcache.patch
target/linux/generic/hack-4.14/220-gc_sections.patch
target/linux/generic/hack-4.14/321-powerpc_crtsavres_prereq.patch
target/linux/generic/pending-4.14/305-mips_module_reloc.patch
target/linux/generic/pending-4.14/611-netfilter_match_bypass_default_table.patch
target/linux/generic/pending-4.14/680-NET-skip-GRO-for-foreign-MAC-addresses.patch

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agox86: refresh configuration
Hauke Mehrtens [Sun, 26 Nov 2017 10:24:11 +0000 (11:24 +0100)]
x86: refresh configuration

Just refresh the kernel configuration, some options are removed because
they are now in the generic kernel configuration.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agokernel: generic: add some more 4.9 configure options
Hauke Mehrtens [Sun, 26 Nov 2017 00:28:37 +0000 (01:28 +0100)]
kernel: generic: add some more 4.9 configure options

These are taken from the x86 target and should make support kernel 4.9
and 4.14 in the x86 target easier.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agoxtables-addons: update to version 2.14
Hauke Mehrtens [Sun, 26 Nov 2017 22:54:03 +0000 (23:54 +0100)]
xtables-addons: update to version 2.14

This includes a compile fix needed for kernel 4.14.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 months agonetdevices.mk: add Sun Neptune 10Gbit Ethernet
Lucian Cristian [Thu, 2 Nov 2017 15:44:02 +0000 (17:44 +0200)]
netdevices.mk: add Sun Neptune 10Gbit Ethernet

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
6 months agokernel: tune e1000e module parameters
Jo-Philipp Wich [Wed, 23 Aug 2017 22:17:56 +0000 (00:17 +0200)]
kernel: tune e1000e module parameters

The default e1000e parameters (interrupt throttling rate, MSI/MSI-X
mode) are optimized for desktop and server computers to optimize
user-space execution (i.e. what's typically referred to as "useful"
work).  This assumption breaks on a router under load where most of
the "useful" work actually takes place either in hardware interrupt
handlers (IRQ) or at software IRQ (swirq) modes, so we try to reflect
that by overriding these parameters with more appropriate values.

Patch-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6 months agox86: add on-chip thermal sensors and cpuid support
Philip Prindeville [Fri, 3 Nov 2017 23:22:29 +0000 (17:22 -0600)]
x86: add on-chip thermal sensors and cpuid support

Cover temperature sensors for all mainstream 64-bit processors, including
AMD 10h and 15h families, Intel iCore, Xeon, Atom, and Via Nano.  Also
add CPUID support for user-space applications to detect CPU type.

Include the on-chip sensors for 64-bit CPU's in the generic profile
in case someone builds a 32-bit kernel to run on a Xeon SoC, etc.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
6 months agox86: refresh settings for 4.9.59
Philip Prindeville [Fri, 3 Nov 2017 23:01:55 +0000 (17:01 -0600)]
x86: refresh settings for 4.9.59

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
6 months agotools/expat: Update to 2.2.5
Daniel Engberg [Mon, 4 Dec 2017 18:23:15 +0000 (19:23 +0100)]
tools/expat: Update to 2.2.5

Update (lib)expat to 2.2.5

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
6 months agobrcm63xx: backport mdio-bus reset gpio support
Jonas Gorski [Wed, 6 Dec 2017 13:12:06 +0000 (14:12 +0100)]
brcm63xx: backport mdio-bus reset gpio support

Backport the mdio-bus reset gpio support from 4.12 and use it instead
of toggling the reset ourself.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
6 months agobrcm63xx: backport enet cleanup patches
Jonas Gorski [Mon, 2 Oct 2017 09:41:43 +0000 (11:41 +0200)]
brcm63xx: backport enet cleanup patches

Align with upstream version, mostly non-fixes and small clean ups.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>