omap: rework image generation and profiles Migrate to new image generation and introduce sdcard generation (based on sunxi). Profile now generated via image/Makefile instead of profiles/ directory. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
package/uboot-omap: re-introduce patches dropped by update to v2017.01 TODO: add commit messages to patches The beagleboard doesn't boot with Thumb enabled, but without Thumb the SPL (first stage bootloader) is too big to fit into SRAM. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
brcm2708: disable CONFIG_BCM2835_THERMAL by default This fixes: Thermal sensors on bcm2835 SoC (BCM2835_THERMAL) [N/m/y/?] (NEW) aborted! This symbol depends on ARCH_BCM2835 so it should be OK to disable it at brcm2708 target only. Fixes: 7d32caa61fb0 ("brcm2708: backport upstream sdhost controller driver") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
kernel: backport Broadcom thermal drivers This includes driver for Northstar and for Raspberry Pi. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
ar71xx: fix ath9k default LED changes fallout Since 192f0a3db859 ("ath9k: unset the default LED pin if used by platform leds") the default ath9k wireless LED is not set as soon as any pin of the ath ath9k gpio controller is used. All touched boards have leds defined which are using the gpio pins exposed by the ath9k driver but rely on a default set wireless led trigger. Add the wireless leds were missing and setup the wireless phy trigger in userspace. Signed-off-by: Russell Senior <russell@personaltelco.net> Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: fix Netgear R6220 package selection The Netgear R6220 requires the kmod-usb3 package and misses kmod-usb-ledtrig-usbport package to setup the configured usb led trigger. Drop the already target selected kmod-mt76. Fixes: FS#686 Fixes: 38bee61dab02 ("ramips: add support for Netgear R6220") Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: add RP-N53 pcie wireless eeprom Fix the PCIe 5GHz wireless by using the on flash eeprom/caldata. Disable the 2.4GHz band as this band has no antennas attached but is enabled in the eeprom/caldata. Fixes: FS#691 Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: fix WHR-600D eeprom dt property Fix the PCIe 5GHz wireless by using the ralink mtd-eeprom property as this board have a RT5592 and uses the rt2x00 driver. The mediathek device tree bindings do not work here. Fixes: FS#691 Fixes: d8dd207ea6f2 ("ramips: use the ralink,mtd-eeprom device tree property") Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: drop rt-n56u factory image The factory image has an uImage header covering the entire image and not only the kernel. The original uImage header which covers only the kernel is appended to the end of the image. During LEDE boot the uImage rootfs splitter skips the whole filesystem, can't find a valid filesystem magic and panics. The last known working version was OpenWrt 14.07, which simply kept on searching for an uImage header if the first found didn't resulted into a working rootfs. This behaviour is kind of error prone since it could produce false positives. Since the sysupgrade image works fine in combination with the tftp recovery for doing the initial installation of LEDE, simply drop the factory image. Related: FS#462 Signed-off-by: Mathias Kresin <dev@kresin.me>
busybox: Move libresolv detection to LEDE Makefile Since the LEDE nslookup applet is already specific to LEDE, move the libresolv detection into the busybox Makefile that LEDE uses. This fixes builds with external toolchains that don't automatically search for headers and/or libraries without being told so. Fixes: de5b8e5d2fe1 ("busybox: add musl compatible nslookup replacement") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>