ipq806x: add ipq4019 fritz4040 support This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
ipq806x: add support for TP-Link Archer VR2600v This router is similar to the C2600. Ethernet on WAN + LAN, switch, sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem and the POTS/DECT interface are not supported yet. It is not possible to flash LEDE via the TP-Link webinterface. The image need to be signed. The first 0x200 bytes of the image is the TP-Link header including the signature. The signature is not validated by the bootloader. The LEDE image is zeroed in this area. To install LEDE it is necessary to solder a four pin header to JP2. Connect a serial interface to this header and interrupt the autostart of kernel. Transfer the sysupgrade image via TFTP and write it to the serial flash at 0x320000. Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
ipq806x: remove device specific sysupgrade image checks Replaced by image metadata Signed-off-by: Felix Fietkau <nbd@nbd.name>
ipq806x: append metadata to images Signed-off-by: Felix Fietkau <nbd@nbd.name>
ipq806x/nbg6817: add sysupgrade support Add new way of flashing to mmc devices based on rootfs split with loop devices. Signed-off-by: André Valentin <avalentin@marcant.net>
ipq806x: add support for indicating the boot and upgrade state using four leds Signed-off-by: Henryk Heisig hyniu@o2.pl
ipq806x: Build image for Netgear Nighthawk X4 R7500v2 Signed-off-by: Alexis Green <alexis@cessp.it> [Jo-Philipp Wich: add missing DEVICE_TITLE, fix model name in commit title] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
ipq806x: add initial support for Netgear R7800 Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
ipq806x: base-files: add support for Linksys EA8500 Signed-off-by: Adrian Panella <ianchi74@outlook.com>
ipq806x/base-files: Add support for Archer C2600 Signed-off-by: Ash Benz <ash.benz@bk.ru>
ipq806x: Add support for Netgear D7800 Signed-off-by: Tathagata Das <tathagata@alumnux.com> SVN-Revision: 48360
ipq806x: fix sysupgrade for AP148 AP148 uses lowercase name as boardname, so we need to use this in platform.sh as well. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 48304
ipq806x: add platform_pre_upgrade for sysupgrade We're in process of cleaning nand_do_platform_check. Currently is leaves a special mark in /tmp/sysupgrade-nand-path triggering some diffent code path in nand_upgrade_stage1. This can be a bit confusing. The plan is to have the check function only check the image and nothing else. Then platform code (platform_pre_upgrade) should trigger NAND specific upgrade path. This is what this patch implements. This follows ar71xx, lantiq and partially bcm53xx. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 46945
ipq806x: add support for Netgear Nighthawk X4 R7500 Add support for the Netgear Nighthawk X4 R7500 and build appropariate sysupgrade and factory images. Known issues: * 5 GHz wifi not working - there is no quantenna driver * One of the USB ports is not working Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 46796
ipq806x: build images and add sysupgrade support for AP148 Add full ubi and sysupgrade images for AP148 and add sysupgrade support for ipq806x to allow updating the current installation. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 46789