lantiq: dts: drop falcon clock node
[openwrt/staging/mkresin.git] / target / linux / lantiq / files-4.14 / arch / mips / boot / dts / EASY98000-base.dtsi
1
2 #include <dt-bindings/interrupt-controller/irq.h>
3 #include <dt-bindings/gpio/gpio.h>
4
5 / {
6 compatible = "lantiq,easy98000", "lantiq,falcon";
7
8 memory@0 {
9 device_type = "memory";
10 reg = <0x0 0x4000000>;
11 };
12
13 easy98000-leds {
14 compatible = "gpio-leds";
15 pinctrl-names = "default";
16 pinctrl-0 = <&bootled_pins>;
17
18 LED_0 {
19 label = "easy98000:green:gpon";
20 gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
21 default-state = "keep";
22 };
23 LED_1 {
24 label = "easy98000:red:gpon";
25 gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>;
26 default-state = "keep";
27 };
28 LED_2 {
29 label = "easy98000:green:gpon_tx";
30 gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
31 default-state = "keep";
32 };
33 LED_3 {
34 label = "easy98000:green:gpon_rx";
35 gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
36 default-state = "keep";
37 };
38 LED_4 {
39 label = "easy98000:green:voice";
40 gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
41 default-state = "keep";
42 };
43 LED_5 {
44 label = "easy98000:green:status";
45 gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
46 default-state = "keep";
47 };
48 };
49 };
50
51 &ebu_cs1 {
52 eth0: ethernet@3 {
53 compatible = "davicom,dm9000";
54 device_type = "network";
55 reg = <0x0000003 0x1>, <0x0000001 0x1>;
56 reg-names = "addr", "data";
57 interrupt-parent = <&gpio1>;
58 #interrupt-cells = <2>;
59 interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
60 local-mac-address = [ 00 00 00 00 00 00 ];
61 };
62
63 cpld@3c00000 {
64 compatible = "lantiq,easy98000_addon";
65 reg = <0x3c00000 0x2>;
66 };
67
68 cpld@3c0000c {
69 compatible = "lantiq,easy98000_cpld_led";
70 reg = <0x3c0000c 0x2>, <0x3c00012 0x2>;
71 };
72 };
73
74 /* // enable this for second uart:
75 &serial1 {
76 status = "okay";
77 };*/
78
79 &spi {
80 status = "okay";
81
82 eeprom@2 {
83 compatible = "atmel,at25", "atmel,at25160n";
84 reg = <2>;
85 spi-max-frequency = <1000000>;
86 spi-cpha;
87 spi-cpol;
88
89 pagesize = <32>;
90 size = <2048>;
91 address-width = <16>;
92 };
93 };
94
95 &i2c {
96 status = "okay";
97
98 clock-frequency = <100000>;
99
100 /* eeprom-emulation by OMU */
101 eeprom@50 {
102 compatible = "at,24c02";
103 reg = <0x50>;
104 };
105 eeprom@51 {
106 compatible = "at,24c02";
107 reg = <0x51>;
108 };
109 };
110