ath79: add support for Teltonika RUT955
authorDaniel Golle <daniel@makrotopia.org>
Sun, 2 Feb 2020 16:09:50 +0000 (18:09 +0200)
committerDaniel Golle <daniel@makrotopia.org>
Fri, 21 Feb 2020 21:35:12 +0000 (22:35 +0100)
Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 4G/3G module (example: Quectel EC-25EU)
- internal microSD slot (spi-mmc, buggy and disabled for now)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-24V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 11x LED (4 are driven by AR9344, 7 by 74HC595)
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector

Serial console (/dev/ttyS0) pinout:

- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side

Flash instruction:

Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.2".

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
target/linux/ath79/dts/ar9344_teltonika_rut955.dts [new file with mode: 0644]
target/linux/ath79/generic/base-files/etc/board.d/02_network
target/linux/ath79/generic/base-files/etc/board.d/03_gpio_switches
target/linux/ath79/image/generic.mk

diff --git a/target/linux/ath79/dts/ar9344_teltonika_rut955.dts b/target/linux/ath79/dts/ar9344_teltonika_rut955.dts
new file mode 100644 (file)
index 0000000..a8aeef0
--- /dev/null
@@ -0,0 +1,346 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9344.dtsi"
+
+/ {
+       model = "Teltonika RUT955";
+       compatible = "teltonika,rut955", "qca,ar9344";
+
+       aliases {
+               serial0 = &uart;
+               serial1 = &hs_uart;
+               led-boot = &led_system_green;
+               led-failsafe = &led_system_red;
+               led-running = &led_system_green;
+               led-upgrade = &led_system_red;
+               label-mac-device = &eth1;
+       };
+
+       i2c {
+               compatible = "i2c-gpio";
+               scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+               sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               hwmon@4d {
+                       compatible = "microchip,mcp3221";
+                       reg = <0x4d>;
+               };
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               signal1 {
+                       label = "rut955:green:signal1";
+                       gpios = <&gpio_ext 0 GPIO_ACTIVE_HIGH>;
+               };
+
+               signal2 {
+                       label = "rut955:green:signal2";
+                       gpios = <&gpio_ext 1 GPIO_ACTIVE_HIGH>;
+               };
+
+               signal3 {
+                       label = "rut955:green:signal3";
+                       gpios = <&gpio_ext 2 GPIO_ACTIVE_HIGH>;
+               };
+
+               signal4 {
+                       label = "rut955:green:signal4";
+                       gpios = <&gpio_ext 3 GPIO_ACTIVE_HIGH>;
+               };
+
+               signal5 {
+                       label = "rut955:green:signal5";
+                       gpios = <&gpio_ext 4 GPIO_ACTIVE_HIGH>;
+               };
+
+               led_system_red: system_red {
+                       label = "rut955:red:system";
+                       gpios = <&gpio_ext 5 GPIO_ACTIVE_HIGH>;
+               };
+
+               led_system_green: system_green {
+                       label = "rut955:green:system";
+                       gpios = <&gpio_ext 6 GPIO_ACTIVE_HIGH>;
+                       default-state = "on";
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               reset {
+                       label = "reset";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+                       debounce-interval = <60>;
+               };
+       };
+};
+
+&gpio {
+       pinctrl-names = "default";
+       pinctrl-0 = <&jtag_disable_pins>;
+
+       gpio-line-names = "RS485_D", "led_wan", "DIN3", "mmc_cs",
+               "ext_sck", "", "", "",
+               "", "", "", "",
+               "ext_mosi", "led_lan2", "led_lan1", "",
+               "i2c_scl", "i2c_sda", "", "DIN2",
+               "ext_cs", "DIN1", "led_lan3", "",
+               "", "", "", "",
+               "", "", "", "";
+
+       ext_sck {
+               gpio-hog;
+               gpios = <4 GPIO_ACTIVE_HIGH>;
+               output-high;
+               line-name = "rut955:ext:sck";
+       };
+
+       ext_mosi {
+               gpio-hog;
+               gpios = <12 GPIO_ACTIVE_HIGH>;
+               output-high;
+               line-name = "rut955:ext:mosi";
+       };
+
+       ext_cs {
+               gpio-hog;
+               gpios = <20 GPIO_ACTIVE_HIGH>;
+               output-low;
+               line-name = "rut955:ext:cs";
+       };
+
+       mmc_cs {
+               gpio-hog;
+               gpios = <3 GPIO_ACTIVE_HIGH>;
+               output-high;
+               line-name = "rut955:mmc:cs";
+       };
+
+       uart1_td {
+               gpio-hog;
+               gpios = <18 GPIO_ACTIVE_HIGH>;
+               output-high;
+               line-name = "rut955:uart1:td";
+       };
+
+       uart1_rd {
+               gpio-hog;
+               gpios = <11 GPIO_ACTIVE_LOW>;
+               input;
+               line-name = "rut955:uart1:rd";
+       };
+
+       led_wan {
+               gpio-hog;
+               gpios = <1 GPIO_ACTIVE_HIGH>;
+               output-high;
+               line-name = "rut955:led:wan";
+       };
+
+       led_lan2 {
+               gpio-hog;
+               gpios = <13 GPIO_ACTIVE_HIGH>;
+               output-high;
+               line-name = "rut955:led:lan2";
+       };
+
+       led_lan1 {
+               gpio-hog;
+               gpios = <14 GPIO_ACTIVE_HIGH>;
+               output-high;
+               line-name = "rut955:led:lan1";
+       };
+
+       led_lan3 {
+               gpio-hog;
+               gpios = <22 GPIO_ACTIVE_HIGH>;
+               output-high;
+               line-name = "rut955:led:lan3";
+       };
+};
+
+&ref {
+       clock-frequency = <40000000>;
+};
+
+&uart {
+       status = "okay";
+};
+
+&hs_uart {
+       status = "okay";
+
+       pinctrl-names = "default";
+       pinctrl-0 = <&pmx_uart2>;
+
+       rts-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+       rs485-rts-active-low;
+       linux,rs485-enabled-at-boot-time;
+};
+
+&spi {
+       status = "okay";
+
+       num-cs = <3>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&pmx_spi>;
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <25000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "u-boot";
+                               reg = <0x0 0x20000>;
+                               read-only;
+                       };
+
+                       config: partition@20000 {
+                               label = "config";
+                               reg = <0x20000 0x10000>;
+                               read-only;
+                       };
+
+                       art: partition@30000 {
+                               label = "art";
+                               reg = <0x30000 0x10000>;
+                               read-only;
+                       };
+
+                       partition@40000 {
+                               label = "firmware";
+                               reg = <0x40000 0xf30000>;
+                               compatible = "tplink,firmware";
+                       };
+
+                       partition@f70000 {
+                               label = "event-log";
+                               reg = <0xf70000 0x90000>;
+                               read-only;
+                       };
+               };
+       };
+
+       microsd@1 {
+               status = "disabled";
+
+               compatible = "mmc-spi-slot";
+               spi-max-frequency = <25000000>;
+               reg = <1>;
+               voltage-ranges = <3200 3400>;
+               broken-cd;
+       };
+
+       gpio_ext: gpio_ext@2 {
+               compatible = "fairchild,74hc595";
+               reg = <2>;
+               gpio-controller;
+               #gpio-cells = <2>;
+               registers-number = <2>;
+               spi-max-frequency = <10000000>;
+               gpio-line-names = "led_signal_bar1", "led_signal_bar2", "led_signal_bar3", "led_signal_bar4",
+                       "led_signal_bar5", "led_status_red", "led_status_green", "sim_sel",
+                       "DOUT1", "DOUT2", "modem_vbus", "modem_rst",
+                       "DOUT3", "RS485_R", "SDCS", "HWRST";
+       };
+};
+
+&usb {
+       #address-cells = <1>;
+       #size-cells = <0>;
+       status = "okay";
+
+       port@1 {
+               #address-cells = <1>;
+               #size-cells = <0>;
+               reg = <1>;
+
+               port@1 {
+                       compatible = "usb-a-connector";
+                       reg = <1>;
+               };
+
+               port@3 {
+                       label = "RS-232 serial adapter";
+                       reg = <3>;
+               };
+
+               port@4 {
+                       label = "internal wwan modem";
+                       reg = <4>;
+               };
+       };
+};
+
+&usb_phy {
+       status = "okay";
+};
+
+&wmac {
+       status = "okay";
+
+       mtd-cal-data = <&art 0x1000>;
+       mtd-mac-address = <&config 0x0>;
+       mtd-mac-address-increment = <2>;
+};
+
+&eth0 {
+       status = "okay";
+
+       phy-handle = <&swphy4>;
+
+       mtd-mac-address = <&config 0x0>;
+       mtd-mac-address-increment = <1>;
+};
+
+&eth1 {
+       status = "okay";
+
+       mtd-mac-address = <&config 0x0>;
+};
+
+&builtin_switch {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pmx_leds_switch>;
+};
+
+&pinmux {
+       pmx_spi: spi {
+               // SPI_CS1 on GPIO 3, 2nd SCK on GPIO 4
+               // 2nd MOSI on GPIO 12, SPI_CS2 on GPIO 20
+               pinctrl-single,bits = <0x0 0x07000000 0xff000000>,
+                                       <0x4 0x0a 0xff>,
+                                       <0xc 0x0b 0xff>,
+                                       <0x14 0x08 0xff>;
+       };
+
+       pmx_leds_switch: leds_switch {
+               // switch port LEDs on GPIO 1, GPIO 13, GPIO 14 and GPIO 22
+               pinctrl-single,bits =  <0x0 0x00002d00 0x0000ff00>,
+                                       <0xc 0x002c2b00 0x00ffff00>,
+                                       <0x14 0x002a0000 0x00ff0000>;
+       };
+
+       pmx_uart2: uart2 {
+               // UART1_DTR on GPIO 0, UART1_RD on GPIO 11, UART1_TD on GPIO 18
+               pinctrl-single,bits = <0x0 0x0 0xff>,
+                               <0x10 0x4f000000 0xff000000>,
+                               <0x3c 0x000b0000 0x00ff0000>;
+       };
+};
index 339cfd111f9bfa25f9ce521daeb161d1ac56fb4d..ef58d9e124a0251d622ee126f27e312fffca0840 100755 (executable)
@@ -220,6 +220,11 @@ ath79_setup_interfaces()
                ucidef_add_switch "switch0" \
                        "0@eth0" "1:lan" "2:lan" "3:wan"
                ;;
+       teltonika,rut955)
+               ucidef_set_interface_wan "eth1"
+               ucidef_add_switch "switch0" \
+                       "0@eth0" "2:lan:3" "3:lan:2" "4:lan:1"
+               ;;
        tplink,archer-a7-v5|\
        tplink,archer-c6-v2|\
        tplink,archer-c6-v2-us|\
index 967e2c76801e946ae7b4073f3ee27c1bbdfd751e..b5b46f16bfaa44410712907dee7e1549ed0e268d 100755 (executable)
@@ -38,6 +38,14 @@ dlink,dir-835-a1)
 librerouter,librerouter-v1)
        ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "1" "0"
        ;;
+teltonika,rut955)
+       ucidef_add_gpio_switch "sim_sel" "SIM select" "503" "1"
+       ucidef_add_gpio_switch "DOUT1" "DOUT1 (OC)" "504" "0"
+       ucidef_add_gpio_switch "DOUT2" "DOUT2 (Relay)" "505" "0"
+       ucidef_add_gpio_switch "modem_vbus" "Modem enable" "506" "1"
+       ucidef_add_gpio_switch "modem_rst" "Modem reset" "507" "0"
+       ucidef_add_gpio_switch "DOUT3" "DOUT3" "508" "0"
+       ;;
 tplink,archer-c25-v1)
        ucidef_add_gpio_switch "led_control" "LED control" "21" "0"
        ucidef_add_gpio_switch "led_reset" "LED reset" "19" "1"
index 1fa9b30c518fa9ba3507cc56d5e3bc74b5de431b..3c0aa2ee4d6869ae8641654db1d905b6934da64a 100644 (file)
@@ -36,6 +36,11 @@ define Build/addpattern
        -mv "$@.new" "$@"
 endef
 
+define Build/append-md5sum-bin
+       $(STAGING_DIR_HOST)/bin/mkhash md5 $@ | sed 's/../\\\\x&/g' |\
+               xargs echo -ne >> $@
+endef
+
 define Build/cybertan-trx
        @echo -n '' > $@-empty.bin
        -$(STAGING_DIR_HOST)/bin/trx -o $@.new \
@@ -73,6 +78,17 @@ define Build/pisen_wmb001n-factory
   rm -rf "$@.tmp"
 endef
 
+define Build/teltonika-fw-fake-checksum
+       # Teltonika U-Boot web based firmware upgrade/recovery routine compares
+       # 16 bytes from md5sum1[16] field in TP-Link v1 header (offset: 76 bytes
+       # from begin of the firmware file) with 16 bytes stored just before
+       # 0xdeadc0de marker. Values are only compared, MD5 sum is not verified.
+       let \
+               offs="$$(stat -c%s $@) - 20"; \
+               dd if=$@ bs=1 count=16 skip=76 |\
+               dd of=$@ bs=1 count=16 seek=$$offs conv=notrunc
+endef
+
 define Device/seama
   KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
   KERNEL_INITRAMFS := $$(KERNEL) | seama
@@ -1070,6 +1086,28 @@ define Device/sitecom_wlr-7100
 endef
 TARGET_DEVICES += sitecom_wlr-7100
 
+define Device/teltonika_rut955
+  SOC := ar9344
+  DEVICE_VENDOR := Teltonika
+  DEVICE_MODEL := RUT955
+  DEVICE_PACKAGES := kmod-usb2 kmod-usb-acm kmod-usb-net-qmi-wwan \
+       kmod-usb-serial-option kmod-hwmon-mcp3021 uqmi -uboot-envtools
+  IMAGE_SIZE := 15552k
+  TPLINK_HWID := 0x35000001
+  TPLINK_HWREV := 0x1
+  TPLINK_HEADER_VERSION := 1
+  KERNEL := kernel-bin | append-dtb | lzma | tplink-v1-header
+  KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma
+  IMAGES += factory.bin
+  IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs |\
+       pad-rootfs | teltonika-fw-fake-checksum | append-string master |\
+       append-md5sum-bin | check-size $$$$(IMAGE_SIZE)
+  IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
+       append-rootfs | pad-rootfs | append-metadata |\
+       check-size $$$$(IMAGE_SIZE)
+endef
+TARGET_DEVICES += teltonika_rut955
+
 define Device/trendnet_tew-823dru
   SOC := qca9558
   DEVICE_VENDOR := Trendnet