target/linux/ramips/dts/WNCE2001.dts

   1 /dts-v1/;
   2
   3 #include "rt3050.dtsi"
   4
   5 / {
   6         compatible = "WNCE2001", "ralink,rt3052-soc";
   7         model = "Netgear WNCE2001";
   8
   9         chosen {
  10                 bootargs = "console=ttyS0,115200";
  11         };
  12
  13         gpio-leds {
  14                 compatible = "gpio-leds";
  15
  16                 power-green {
  17                         label = "wnce2001:green:power";
  18                         gpios = <&gpio0 8 1>;
  19                 };
  20
  21                 power-red {
  22                         label = "wnce2001:red:power";
  23                         gpios = <&gpio0 9 1>;
  24                 };
  25
  26                 wlan-green {
  27                         label = "wnce2001:green:wlan";
  28                         gpios = <&gpio0 12 0>;
  29                 };
  30
  31                 wlan-red {
  32                         label = "wnce2001:red:wlan";
  33                         gpios = <&gpio0 13 0>;
  34                 };
  35         };
  36
  37         gpio-keys-polled {
  38                 compatible = "gpio-keys-polled";
  39                 #address-cells = <1>;
  40                 #size-cells = <0>;
  41                 poll-interval = <20>;
  42
  43                 reset {
  44                         label = "reset";
  45                         gpios = <&gpio0 10 1>;
  46                         linux,code = <0x198>;
  47                 };
  48
  49                 wps {
  50                         label = "wps";
  51                         gpios = <&gpio0 0 1>;
  52                         linux,code = <0x211>;
  53                 };
  54
  55                 rt {
  56                         label = "rt";
  57                         gpios = <&gpio0 11 1>;
  58                         linux,code = <0x100>;
  59                 };
  60
  61                 ap {
  62                         label = "ap";
  63                         gpios = <&gpio0 7 1>;
  64                         linux,code = <0x101>;
  65                 };
  66         };
  67 };
  68
  69 &spi0 {
  70         status = "okay";
  71
  72         m25p80@0 {
  73                 #address-cells = <1>;
  74                 #size-cells = <1>;
  75                 compatible = "jedec,spi-nor";
  76                 reg = <0>;
  77                 linux,modalias = "m25p80", "mx25l3205d";
  78                 spi-max-frequency = <10000000>;
  79
  80                 partition@0 {
  81                         label = "u-boot";
  82                         reg = <0x0 0x30000>;
  83                         read-only;
  84                 };
  85
  86                 factory: partition@30000 {
  87                         label = "factory";
  88                         reg = <0x30000 0x10000>;
  89                         read-only;
  90                 };
  91
  92                 partition@40000 {
  93                         label = "config";
  94                         reg = <0x40000 0x20000>;
  95                         read-only;
  96                 };
  97
  98                 partition@60000 {
  99                         label = "language";
 100                         reg = <0x60000 0x30000>;
 101                         read-only;
 102                 };
 103
 104                 partition@90000 {
 105                         label = "pot";
 106                         reg = <0x90000 0x10000>;
 107                         read-only;
 108                 };
 109
 110                 partition@a0000 {
 111                         label = "checksum";
 112                         reg = <0xa0000 0x10000>;
 113                 };
 114
 115                 partition@b0000 {
 116                         label = "firmware";
 117                         reg = <0xb0000 0x350000>;
 118                 };
 119         };
 120 };
 121
 122 &pinctrl {
 123         state_default: pinctrl0 {
 124                 gpio {
 125                         ralink,group = "i2c", "jtag", "rgmii", "mdio", "uartf";
 126                         ralink,function = "gpio";
 127                 };
 128         };
 129 };
 130
 131 &ethernet {
 132         mtd-mac-address = <&factory 0x28>;
 133 };
 134
 135 &wmac {
 136         ralink,mtd-eeprom = <&factory 0>;
 137 };