/dts-v1/;
-/include/ "rt3883.dtsi"
+#include "rt3883.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
/ {
- compatible = "BR-6475ND", "ralink,rt3883-soc";
+ compatible = "edimax,br-6475nd", "ralink,rt3883-soc";
model = "Edimax BR-6475nD";
- pinctrl {
- state_default: pinctrl0 {
- gpio {
- ralink,group = "spi", "jtag", "uartf";
- ralink,function = "gpio";
- };
- };
+ aliases {
+ led-status = &led_power;
};
- palmbus@10000000 {
- timer@100 {
- status = "okay";
- };
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ poll-interval = <100>;
- gpio1: gpio@638 {
- status = "okay";
+ reset {
+ label = "reset";
+ gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
};
- uartlite@c00 {
- status = "okay";
+ rfkill {
+ label = "rfkill";
+ gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_SW>;
+ linux,code = <KEY_RFKILL>;
};
};
- ethernet@10100000 {
- status = "okay";
- mtd-mac-address = <&devdata 0x0d>;
+ gpio-leds {
+ compatible = "gpio-leds";
- port@0 {
- ralink,fixed-link = <1000 1 1 1>;
+ led_power: power {
+ label = "br-6475nd:green:power";
+ gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
};
- };
-
- wmac@10180000 {
- ralink,mtd-eeprom = <&factory 0>;
- };
-
- pci@10140000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&pci_pins>;
- pci_pins: pci {
- pci {
- ralink,group = "pci";
- ralink,function = "pci-fnc";
- };
+ wlan {
+ label = "br-6475nd:amber:wlan";
+ gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
};
- host-bridge {
- pci-bridge@1 {
- status = "okay";
- wmac@0,0 {
- compatible = "ralink,rt2880-pci", "pciclass060400", "pciclass0604";
- reg = < 0x10000 0 0 0 0 >;
- ralink,eeprom = "soc_wmac.eeprom";
- };
- };
+ wlan_5ghz {
+ label = "br-6475nd:amber:wlan_5ghz";
+ gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
};
};
- ehci@101c0000 {
- status = "okay";
- };
-
- ohci@101c1000 {
- status = "okay";
- };
-
nor-flash@1c000000 {
compatible = "cfi-flash";
reg = <0x1c000000 0x800000>;
-
bank-width = <2>;
- #address-cells = <1>;
- #size-cells = <1>;
- partition@0 {
- reg = <0x00000000 0x00030000>;
- label = "u-boot";
- read-only;
- };
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
- partition@30000 {
- reg = <0x00030000 0x00010000>;
- label = "nvram";
- read-only;
- };
+ partition@0 {
+ reg = <0x00000000 0x00030000>;
+ label = "u-boot";
+ read-only;
+ };
- factory: partition@40000 {
- reg = <0x00040000 0x00010000>;
- label = "factory";
- read-only;
- };
+ partition@30000 {
+ reg = <0x00030000 0x00010000>;
+ label = "nvram";
+ read-only;
+ };
- devdata: partition@50000 {
- reg = <0x00050000 0x00020000>;
- label = "devdata";
- read-only;
- };
+ factory: partition@40000 {
+ reg = <0x00040000 0x00010000>;
+ label = "factory";
+ read-only;
+ };
- partition@70000 {
- reg = <0x00070000 0x00790000>;
- label = "firmware";
- };
+ devdata: partition@50000 {
+ reg = <0x00050000 0x00020000>;
+ label = "devdata";
+ read-only;
+ };
- partition@170000 {
- reg = <0x00270000 0x00590000>;
- label = "rootfs";
+ partition@70000 {
+ reg = <0x00070000 0x00790000>;
+ label = "firmware";
+ };
};
};
rtl8367 {
compatible = "realtek,rtl8367";
- gpio-sda = <&gpio0 5 0>;
- gpio-sck = <&gpio0 4 0>;
+ gpio-sda = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+ gpio-sck = <&gpio0 4 GPIO_ACTIVE_HIGH>;
realtek,extif0 = <1 0 1 1 1 1 1 1 2>;
};
- gpio-keys-polled {
- compatible = "gpio-keys-polled";
- #address-cells = <1>;
- #size-cells = <0>;
- poll-interval = <100>;
- reset {
- label = "reset";
- gpios = <&gpio0 7 1>;
- linux,code = <0x198>;
- };
- rfkill {
- label = "rfkill";
- gpios = <&gpio0 9 1>;
- linux,input-type = <5>;
- linux,code = <0xf7>;
- };
- };
-
- gpio-leds {
- compatible = "gpio-leds";
-
- power {
- label = "edimax:green:power";
- gpios = <&gpio0 10 1>;
- };
- wlan {
- label = "edimax:amber:wlan";
- gpios = <&gpio0 11 1>;
- };
- wlan_5ghz {
- label = "edimax:amber:wlan_5ghz";
- gpios = <&gpio0 14 1>;
- };
- };
-
- /* Unclear if this is the correct gpio setup; the USB ports are
- unpopulated on a stock BR-6475nD, even though the hardware exists
- and the headers are there. */
+ /*
+ * Unclear if this is the correct gpio setup; the USB ports are
+ * unpopulated on a stock BR-6475nD, even though the hardware exists
+ * and the headers are there.
+ */
/*
gpio_export {
compatible = "gpio-export";
#size-cells = <0>;
+
usb {
gpio-export,name="usb";
gpio-export,output=<0>;
- gpios = <&gpio0 19 0>;
+ gpios = <&gpio0 19 GPIO_ACTIVE_LOW>;
};
};
*/
};
+
+&pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "spi", "jtag", "uartf";
+ ralink,function = "gpio";
+ };
+ };
+};
+
+&timer {
+ status = "okay";
+};
+
+&gpio1 {
+ status = "okay";
+};
+
+&uartlite {
+ status = "okay";
+};
+
+ðernet {
+ status = "okay";
+ mtd-mac-address = <&devdata 0x0d>;
+
+ port@0 {
+ mediatek,fixed-link = <1000 1 1 1>;
+ };
+};
+
+&wmac {
+ status = "okay";
+ ralink,mtd-eeprom = <&factory 0>;
+};
+
+&pci {
+ status = "okay";
+};
+
+&pci1 {
+ status = "okay";
+
+ wifi@0,0 {
+ compatible = "pci0,0";
+ reg = <0x10000 0 0 0 0>;
+ ralink,5ghz = <0>;
+ ralink,mtd-eeprom = <&factory 0x8000>;
+ };
+};
+
+&ehci {
+ status = "okay";
+};
+
+&ohci {
+ status = "okay";
+};
projects / openwrt / staging / wigyori.git / blobdiff