CONFIG_GENERIC_IRQ_CHIP=y
CONFIG_GENERIC_IRQ_SHOW=y
CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_PINCONF=y
CONFIG_GENERIC_SCHED_CLOCK=y
CONFIG_GENERIC_SMP_IDLE_THREAD=y
CONFIG_GENERIC_TIME_VSYSCALL=y
CONFIG_LEDS_GPIO=y
CONFIG_LIBFDT=y
CONFIG_MDIO_BOARDINFO=y
+CONFIG_MFD_SYSCON=y
CONFIG_MIPS=y
CONFIG_MIPS_CLOCK_VSYSCALL=y
# CONFIG_MIPS_CMDLINE_DTB_EXTEND is not set
CONFIG_PERF_USE_VMALLOC=y
CONFIG_PGTABLE_LEVELS=2
CONFIG_PHYLIB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_BCM6318=y
+CONFIG_PINCTRL_BCM63268=y
+CONFIG_PINCTRL_BCM6328=y
+CONFIG_PINCTRL_BCM6348=y
+CONFIG_PINCTRL_BCM6358=y
+CONFIG_PINCTRL_BCM6362=y
+CONFIG_PINCTRL_BCM6368=y
+CONFIG_PINCTRL_BCM63XX=y
CONFIG_POSIX_MQUEUE=y
CONFIG_POSIX_MQUEUE_SYSCTL=y
# CONFIG_RCU_STALL_COMMON is not set
+CONFIG_REGMAP=y
+CONFIG_REGMAP_MMIO=y
CONFIG_RELAY=y
CONFIG_RTL8366_SMI=y
CONFIG_RTL8367_PHY=y
wps {
label = "wps";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_WPS_BUTTON>;
};
reset {
label = "reset";
- gpios = <&gpio1 5 1>;
+ gpios = <&pinctrl 37 1>;
linux,code = <KEY_RESTART>;
};
};
voip_red {
label = "DWV-S0:red:VoIP";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
};
eth_red {
label = "DWV-S0:red:ethernet";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
dsl_green {
label = "DWV-S0:green:ADSL";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
usb_green {
label = "DWV-S0:green:USB";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
power_green {
label = "DWV-S0:green:power";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
default-state = "on";
};
power_red {
label = "DWV-S0:red:power";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
inet_red {
label = "DWV-S0:red:internet";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
};
inet_green {
label = "DWV-S0:green:internet";
- gpios = <&gpio0 7 1>;
+ gpios = <&pinctrl 7 1>;
};
eth_green {
label = "DWV-S0:green:ethernet";
- gpios = <&gpio0 8 1>;
+ gpios = <&pinctrl 8 1>;
};
voip_green {
label = "DWV-S0:green:VoIP";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
};
wifi_red {
label = "DWV-S0:red:wifi";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
};
usb_red {
label = "DWV-S0:red:USB";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
dsl_red {
label = "DWV-S0:red:ADSL";
- gpios = <&gpio0 12 1>;
+ gpios = <&pinctrl 12 1>;
};
};
};
wps {
label = "wps";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_WPS_BUTTON>;
};
reset {
label = "reset";
- gpios = <&gpio1 5 1>;
+ gpios = <&pinctrl 37 1>;
linux,code = <KEY_RESTART>;
};
};
voip_red {
label = "DWV-S0:red:VoIP";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
};
eth_red {
label = "DWV-S0:red:ethernet";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
dsl_green {
label = "DWV-S0:green:ADSL";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
usb_green {
label = "DWV-S0:green:USB";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
power_green {
label = "DWV-S0:green:power";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
default-state = "on";
};
power_red {
label = "DWV-S0:red:power";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
inet_red {
label = "DWV-S0:red:internet";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
};
inet_green {
label = "DWV-S0:green:internet";
- gpios = <&gpio0 7 1>;
+ gpios = <&pinctrl 7 1>;
};
eth_green {
label = "DWV-S0:green:ethernet";
- gpios = <&gpio0 8 1>;
+ gpios = <&pinctrl 8 1>;
};
voip_green {
label = "DWV-S0:green:VoIP";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
};
wifi_red {
label = "DWV-S0:red:wifi";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
};
usb_red {
label = "DWV-S0:red:USB";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
dsl_red {
label = "DWV-S0:red:ADSL";
- gpios = <&gpio0 12 1>;
+ gpios = <&pinctrl 12 1>;
};
};
};
wps {
label = "wps";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_WPS_BUTTON>;
};
reset {
label = "reset";
- gpios = <&gpio1 5 1>;
+ gpios = <&pinctrl 37 1>;
linux,code = <KEY_RESTART>;
};
};
voip_red {
label = "DWV-S0:red:VoIP";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
};
eth_red {
label = "DWV-S0:red:ethernet";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
dsl_green {
label = "DWV-S0:green:ADSL";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
usb_green {
label = "DWV-S0:green:USB";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
power_green {
label = "DWV-S0:green:power";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
default-state = "on";
};
power_red {
label = "DWV-S0:red:power";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
inet_red {
label = "DWV-S0:red:internet";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
};
inet_green {
label = "DWV-S0:green:internet";
- gpios = <&gpio0 7 1>;
+ gpios = <&pinctrl 7 1>;
};
eth_green {
label = "DWV-S0:green:ethernet";
- gpios = <&gpio0 8 1>;
+ gpios = <&pinctrl 8 1>;
};
voip_green {
label = "DWV-S0:green:VoIP";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
};
wifi_red {
label = "DWV-S0:red:wifi";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
};
usb_red {
label = "DWV-S0:red:USB";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
dsl_red {
label = "DWV-S0:red:ADSL";
- gpios = <&gpio0 12 1>;
+ gpios = <&pinctrl 12 1>;
};
};
};
reset {
label = "reset";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
- gpios = <&gpio0 24 1>;
+ gpios = <&pinctrl 24 1>;
linux,code = <KEY_WPS_BUTTON>;
};
};
inet_red {
label = "A4001N:red:inet";
- gpios = <&gpio0 1 0>;
+ gpios = <&pinctrl 1 0>;
};
power_red {
label = "A4001N:red:power";
- gpios = <&gpio0 4 0>;
+ gpios = <&pinctrl 4 0>;
};
power_green {
label = "A4001N:green:power";
- gpios = <&gpio0 8 0>;
+ gpios = <&pinctrl 8 0>;
default-state = "on";
};
usb_green {
label = "A4001N:green:usb";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
};
dsl_green {
label = "A4001N:green:dsl";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
};
};
reset {
label = "reset";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wlan";
- gpios = <&gpio0 24 1>;
+ gpios = <&pinctrl 24 1>;
linux,code = <KEY_WLAN>;
};
};
inet_red {
label = "A4001N1:red:inet";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
ppp_green {
label = "A4001N1:green:ppp";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
power_green {
label = "A4001N1:green:power";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
default-state = "on";
};
ppp_red {
label = "A4001N1:red:ppp";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
usb_green {
label = "A4001N1:green:3g";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
};
usb_red {
label = "A4001N1:red:3g";
- gpios = <&gpio0 7 1>;
+ gpios = <&pinctrl 7 1>;
};
power_red {
label = "A4001N1:red:power";
- gpios = <&gpio0 8 1>;
+ gpios = <&pinctrl 8 1>;
};
wlan_green {
label = "A4001N1:green:wlan";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
};
wlan_red {
label = "A4001N1:red:wlan";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
};
inet_green {
label = "A4001N1:green:inet";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
eth_red {
label = "A4001N1:red:eth";
- gpios = <&gpio0 20 1>;
+ gpios = <&pinctrl 20 1>;
};
eth_green {
label = "A4001N1:green:eth";
- gpios = <&gpio0 31 1>;
+ gpios = <&pinctrl 31 1>;
};
};
};
wps {
label = "wps";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_WPS_BUTTON>;
};
reset {
label = "reset";
- gpios = <&gpio1 5 1>;
+ gpios = <&pinctrl 37 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "AGPF-S0:green:power";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
default-state = "on";
};
power_red {
label = "AGPF-S0:red:power";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
service_green {
label = "AGPF-S0:green:service";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
};
service_red {
label = "AGPF-S0:red:service";
- gpios = <&gpio0 7 1>;
+ gpios = <&pinctrl 7 1>;
};
dsl_green {
label = "AGPF-S0:green:adsl";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
};
dsl_red {
label = "AGPF-S0:red:adsl";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
};
wifi_green {
label = "AGPF-S0:green:wifi";
- gpios = <&gpio0 22 1>;
+ gpios = <&pinctrl 22 1>;
};
wifi_red {
label = "AGPF-S0:red:wifi";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
};
inet_red {
label = "AGPF-S0:red:internet";
- gpios = <&gpio0 24 1>;
+ gpios = <&pinctrl 24 1>;
};
inet_green {
label = "AGPF-S0:green:internet";
- gpios = <&gpio0 25 1>;
+ gpios = <&pinctrl 25 1>;
};
usr1_green {
label = "AGPF-S0:green:usr1";
- gpios = <&gpio0 26 1>;
+ gpios = <&pinctrl 26 1>;
};
usr1_red {
label = "AGPF-S0:red:usr1";
- gpios = <&gpio0 27 1>;
+ gpios = <&pinctrl 27 1>;
};
usr2_green {
label = "AGPF-S0:green:usr2";
- gpios = <&gpio0 29 1>;
+ gpios = <&pinctrl 29 1>;
};
usr2_red {
label = "AGPF-S0:red:usr2";
- gpios = <&gpio0 30 1>;
+ gpios = <&pinctrl 30 1>;
};
};
};
reset {
label = "reset";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
linux,code = <KEY_RESTART>;
};
};
alarm_red {
label = "AR-5381u:red:alarm";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
inet_green {
label = "AR-5381u:green:inet";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
power_green {
label = "AR-5381u:green:power";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
default-state = "on";
};
};
reset {
label = "reset";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
linux,code = <KEY_RESTART>;
};
};
inet_red {
label = "AR-5387un:red:inet";
- gpios = <&gpio0 1 0>;
+ gpios = <&pinctrl 1 0>;
};
power_red {
label = "AR-5387un:red:power";
- gpios = <&gpio0 4 0>;
+ gpios = <&pinctrl 4 0>;
};
inet_green {
label = "AR-5387un:green:inet";
- gpios = <&gpio0 7 0>;
+ gpios = <&pinctrl 7 0>;
};
power_green {
label = "AR-5387un:green:power";
- gpios = <&gpio0 8 0>;
+ gpios = <&pinctrl 8 0>;
default-state = "on";
};
dsl_green {
label = "AR-5387un:green:dsl";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
};
};
reset {
label = "reset";
- gpios = <&gpio1 1 1>;
+ gpios = <&pinctrl 33 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "AR1004G:green:power";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
default-state = "on";
};
inet_green {
label = "AR1004G:green:inet";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
power_red {
label = "AR1004G:red:power";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
};
};
};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ext_mii &pinctrl_pci>;
+};
reset {
label = "reset";
- gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+ gpios = <&pinctrl 34 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wlan {
label = "wlan";
- gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+ gpios = <&pinctrl 37 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WLAN>;
};
};
power_white {
label = "AV4202N:white:power";
- gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
+ gpios = <&pinctrl 10 GPIO_ACTIVE_LOW>;
default-state = "on";
};
power_red {
label = "AV4202N:red:power";
- gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+ gpios = <&pinctrl 11 GPIO_ACTIVE_LOW>;
};
wan_white {
label = "AV4202N:white:wan";
- gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+ gpios = <&pinctrl 26 GPIO_ACTIVE_LOW>;
};
wan_red {
label = "AV4202N:red:wan";
- gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
+ gpios = <&pinctrl 27 GPIO_ACTIVE_LOW>;
};
phone_white {
label = "AV4202N:white:phone";
- gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+ gpios = <&pinctrl 24 GPIO_ACTIVE_LOW>;
};
phone_red {
label = "AV4202N:red:phone";
- gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
+ gpios = <&pinctrl 25 GPIO_ACTIVE_LOW>;
};
wifi {
label = "AV4202N:blue:wifi";
- gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
+ gpios = <&pinctrl 22 GPIO_ACTIVE_LOW>;
};
};
};
compatible = "brcm,bcm6318";
aliases {
- gpio0 = &gpio0;
- gpio1 = &gpio1;
+ pinctrl = &pinctrl;
spi1 = &hsspi;
};
interrupts = <2>;
};
- gpio1: gpio-controller@10000080 {
- compatible = "brcm,bcm6345-gpio";
- reg = <0x10000080 4>, <0x10000088 4>;
+ pinctrl: pin-controller@10000080 {
+ compatible = "brcm,bcm6318-pinctrl";
+ reg = <0x10000080 0x08>,
+ <0x10000088 0x08>,
+ <0x10000098 0x04>,
+ <0x1000009c 0x0c>,
+ <0x100000d4 0x18>;
+ reg-names = "dirout", "dat", "mode", "mux", "pad";
gpio-controller;
#gpio-cells = <2>;
- ngpios = <18>;
-
interrupt-parent = <&ext_intc>;
interrupts = <0 0>, <1 0>;
- interrupt-names = "gpio1", "gpio2";
- };
-
- gpio0: gpio-controller@10000084 {
- compatible = "brcm,bcm6345-gpio";
- reg = <0x10000084 4>, <0x1000008c 4>;
-
- gpio-controller;
- #gpio-cells = <2>;
+ interrupt-names = "gpio33", "gpio34";
+
+ pinctrl_ephy0_spd_led: ephy0_spd_led {
+ function = "ephy0_spd_led";
+ pins = "gpio0";
+ };
+
+ pinctrl_ephy1_spd_led: ephy1_spd_led {
+ function = "ephy1_spd_led";
+ pins = "gpio1";
+ };
+
+ pinctrl_ephy2_spd_led: ephy2_spd_led {
+ function = "ephy2_spd_led";
+ pins = "gpio2";
+ };
+
+ pinctrl_ephy3_spd_led: ephy3_spd_led {
+ function = "ephy3_spd_led";
+ pins = "gpio3";
+ };
+
+ pinctrl_ephy0_act_led: ephy0_act_led {
+ function = "ephy0_act_led";
+ pins = "gpio4";
+ };
+
+ pinctrl_ephy1_act_led: ephy1_act_led {
+ function = "ephy1_act_led";
+ pins = "gpio5";
+ };
+
+ pinctrl_ephy2_act_led: ephy2_act_led {
+ function = "ephy2_act_led";
+ pins = "gpio6";
+ };
+
+ pinctrl_ephy3_act_led: ephy3_act_led {
+ function = "ephy3_act_led";
+ pins = "gpio7";
+ };
+
+ pinctrl_serial_led: serial_led {
+ pinctrl_serial_led_data: serial_led_data {
+ function = "serial_led_data";
+ pins = "gpio6";
+ };
+
+ pinctrl_serial_led_clk: serial_led_clk {
+ function = "serial_led_clk";
+ pins = "gpio7";
+ };
+ };
+
+ pinctrl_inet_act_led: inet_act_led {
+ function = "inet_act_led";
+ pins = "gpio8";
+ };
+
+ pinctrl_inet_fail_led: inet_fail_led {
+ function = "inet_fail_led";
+ pins = "gpio9";
+ };
+
+ pinctrl_dsl_led: dsl_led {
+ function = "dsl_led";
+ pins = "gpio10";
+ };
+
+ pinctrl_post_fail_led: post_fail_led {
+ function = "post_fail_led";
+ pins = "gpio11";
+ };
+
+ pinctrl_wlan_wps_led: wlan_wps_led {
+ function = "wlan_wps_led";
+ pins = "gpio12";
+ };
+
+ pinctrl_usb_pwron: usb_pwron {
+ function = "usb_pwron";
+ pins = "gpio13";
+ };
+
+ pinctrl_usb_device_led: usb_device_led {
+ function = "usb_device_led";
+ pins = "gpio13";
+ };
+
+ pinctrl_usb_active: usb_active {
+ function = "usb_active";
+ pins = "gpio40";
+ };
};
hsspi: spi@10003000 {
compatible = "brcm,bcm63268";
aliases {
- gpio0 = &gpio0;
- gpio1 = &gpio1;
+ pinctrl = &pinctrl;
spi0 = &lsspi;
spi1 = &hsspi;
};
interrupts = <2>, <3>;
};
- gpio1: gpio-controller@100000c0 {
- compatible = "brcm,bcm6345-gpio";
- reg = <0x100000c0 4>, <0x100000c8 4>;
+ pinctrl: pin-controller@100000c0 {
+ compatible = "brcm,bcm63268-pinctrl";
+ reg = <0x100000c0 0x8>,
+ <0x100000c8 0x8>,
+ <0x100000d0 0x4>,
+ <0x100000d8 0x4>,
+ <0x100000dc 0x4>,
+ <0x100000f8 0x4>;
+ reg-names = "dirout", "dat", "led", "mode",
+ "ctrl", "basemode";
gpio-controller;
#gpio-cells = <2>;
- ngpios = <20>;
-
interrupt-parent = <&periph_intc>;
interrupts = <0 0>, <1 0>, <2 0>, <3 0>;
- interrupt-names = "gpio0", "gpio1", "gpio2", "gpio3";
- };
-
- gpio0: gpio-controller@100000c4 {
- compatible = "brcm,bcm6345-gpio";
- reg = <0x100000c4 4>, <0x100000cc 4>;
-
- gpio-controller;
- #gpio-cells = <2>;
+ interrupt-names = "gpio32", "gpio33", "gpio34", "gpio35";
+
+ pinctrl_serial_led: serial_led {
+ pinctrl_serial_led_clk: serial_led_clk {
+ function = "serial_led_clk";
+ pins = "gpio0";
+ };
+
+ pinctrl_serial_led_data: serial_led_data {
+ function = "serial_led_data";
+ pins = "gpio1";
+ };
+ };
+
+ pinctrl_hsspi_cs4: hsspi_cs4 {
+ function = "hsspi_cs4";
+ pins = "gpio16";
+ };
+
+ pinctrl_hsspi_cs5: hsspi_cs5 {
+ function = "hsspi_cs5";
+ pins = "gpio17";
+ };
+
+ pinctrl_hsspi_cs6: hsspi_cs6 {
+ function = "hsspi_cs6";
+ pins = "gpio8";
+ };
+
+ pinctrl_hsspi_cs7: hsspi_cs7 {
+ function = "hsspi_cs7";
+ pins = "gpio9";
+ };
+
+ pinctrl_adsl_spi: adsl_spi {
+ pinctrl_adsl_spi_miso: adsl_spi_miso {
+ function = "adsl_spi_miso";
+ pins = "gpio18";
+ };
+
+ pinctrl_adsl_spi_mosi: adsl_spi_mosi {
+ function = "adsl_spi_mosi";
+ pins = "gpio19";
+ };
+ };
+
+ pinctrl_vreq_clk: vreq_clk {
+ function = "vreq_clk";
+ pins = "gpio22";
+ };
+
+ pinctrl_pcie_clkreq_b: pcie_clkreq_b {
+ function = "pcie_clkreq_b";
+ pins = "gpio23";
+ };
+
+ pinctrl_robosw_led_clk: robosw_led_clk {
+ function = "robosw_led_clk";
+ pins = "gpio30";
+ };
+
+ pinctrl_robosw_led_data: robosw_led_data {
+ function = "robosw_led_data";
+ pins = "gpio31";
+ };
+
+ pinctrl_nand: nand {
+ function = "nand";
+ group = "nand_grp";
+ };
+
+ pinctrl_gpio35_alt: gpio35_alt {
+ function = "gpio35_alt";
+ pin = "gpio35";
+ };
+
+ pinctrl_dectpd: dectpd {
+ function = "dectpd";
+ group = "dectpd_grp";
+ };
+
+ pinctrl_vdsl_phy_override_0: vdsl_phy_override_0 {
+ function = "vdsl_phy_override_0";
+ group = "vdsl_phy_override_0_grp";
+ };
+
+ pinctrl_vdsl_phy_override_1: vdsl_phy_override_1 {
+ function = "vdsl_phy_override_1";
+ group = "vdsl_phy_override_1_grp";
+ };
+
+ pinctrl_vdsl_phy_override_2: vdsl_phy_override_2 {
+ function = "vdsl_phy_override_2";
+ group = "vdsl_phy_override_2_grp";
+ };
+
+ pinctrl_vdsl_phy_override_3: vdsl_phy_override_3 {
+ function = "vdsl_phy_override_3";
+ group = "vdsl_phy_override_3_grp";
+ };
+
+ pinctrl_dsl_gpio8: dsl_gpio8 {
+ function = "dsl_gpio8";
+ group = "dsl_gpio8";
+ };
+
+ pinctrl_dsl_gpio9: dsl_gpio9 {
+ function = "dsl_gpio9";
+ group = "dsl_gpio9";
+ };
};
lsspi: spi@10000800 {
compatible = "brcm,bcm6328";
aliases {
- gpio0 = &gpio0;
+ pinctrl = &pinctrl;
spi1 = &hsspi;
};
interrupts = <2>;
};
- gpio0: gpio-controller@10000084 {
- compatible = "brcm,bcm6345-gpio";
- reg = <0x10000084 4>, <0x1000008c 4>;
+ pinctrl: pin-controller@10000080 {
+ compatible = "brcm,bcm6328-pinctrl";
+ reg = <0x10000080 0x8>,
+ <0x10000088 0x8>,
+ <0x10000098 0x4>,
+ <0x1000009c 0xc>;
+ reg-names = "dirout", "dat", "mode", "mux";
gpio-controller;
#gpio-cells = <2>;
interrupts = <3 0>, <2 0>, <0 0>, <1 0>;
interrupt-names = "gpio12", "gpio15",
"gpio23", "gpio24";
+
+ pinctrl_serial_led: serial_led {
+ pinctrl_serial_led_data: serial_led_data {
+ function = "serial_led_data";
+ pins = "gpio6";
+ };
+
+ pinctrl_serial_led_clk: serial_led_clk {
+ function = "serial_led_clk";
+ pins = "gpio7";
+ };
+ };
+
+ pinctrl_inet_act_led: inet_act_led {
+ function = "inet_act_led";
+ pins = "gpio11";
+ };
+
+ pinctrl_pcie_clkreq: pcie_clkreq {
+ function = "pcie_clkreq";
+ pins = "gpio16";
+ };
+
+ pinctrl_ephy0_spd_led: ephy0_spd_led {
+ function = "led";
+ pins = "gpio17";
+ };
+
+ pinctrl_ephy1_spd_led: ephy1_spd_led {
+ function = "led";
+ pins = "gpio18";
+ };
+
+ pinctrl_ephy2_spd_led: ephy2_spd_led {
+ function = "led";
+ pins = "gpio19";
+ };
+
+ pinctrl_ephy3_spd_led: ephy3_spd_led {
+ function = "led";
+ pins = "gpio20";
+ };
+
+ pinctrl_ephy0_act_led: ephy0_act_led {
+ function = "ephy0_act_led";
+ pins = "gpio25";
+ };
+
+ pinctrl_ephy1_act_led: ephy1_act_led {
+ function = "ephy1_act_led";
+ pins = "gpio26";
+ };
+
+ pinctrl_ephy2_act_led: ephy2_act_led {
+ function = "ephy2_act_led";
+ pins = "gpio27";
+ };
+
+ pinctrl_ephy3_act_led: ephy3_act_led {
+ function = "ephy3_act_led";
+ pins = "gpio28";
+ };
+
+ pinctrl_hsspi_cs1: hsspi_cs1 {
+ function = "hsspi_cs1";
+ pins = "hsspi_cs1";
+ };
+
+ pinctrl_usb_port1_device: usb_port1_device {
+ function = "usb_device_port";
+ pins = "usb_port1";
+ };
+
+ pinctrl_usb_port1_host: usb_port1_host {
+ function = "usb_host_port";
+ pins = "usb_port1";
+ };
};
hsspi: spi@10001000 {
aliases {
pflash = &pflash;
- gpio0 = &gpio0;
- gpio1 = &gpio1;
+ pinctrl = &pinctrl;
spi0 = &lsspi;
};
brcm,field-width = <5>;
};
- gpio1: gpio-controller@fffe0400 {
- compatible = "brcm,bcm6345-gpio";
- reg = <0xfffe0400 4>, <0xfffe0408 4>;
+ pinctrl: pin-controller@fffe0400 {
+ compatible = "brcm,bcm6348-pinctrl";
+ reg = <0xfffe0400 0x8>,
+ <0xfffe0408 0x8>,
+ <0xfffe0418 0x4>;
+ reg-names = "dirout", "dat", "mode";
gpio-controller;
#gpio-cells = <2>;
- ngpios = <5>;
-
interrupt-parent = <&ext_intc>;
interrupts = <0 0>, <1 0>, <2 0>, <3 0>;
- interrupt-names = "gpio0", "gpio1", "gpio2", "gpio3";
- };
-
- gpio0: gpio-controller@fffe0404 {
- compatible = "brcm,bcm6345-gpio";
- reg = <0xfffe0404 4>, <0xfffe040c 4>;
-
- gpio-controller;
- #gpio-cells = <2>;
+ interrupt-names = "gpio32", "gpio33", "gpio34", "gpio35";
+
+ pinctrl_ext_ephy: ext_ephy {
+ function = "ext_ephy";
+ groups = "group1", "group4";
+ };
+
+ pinctrl_mii_snoop: mii_snoop {
+ function = "ext_ephy";
+ groups = "group1", "group4";
+ };
+
+ pinctrl_legacy_led: legacy_led {
+ function = "legacy_led";
+ groups = "group4";
+ };
+
+ pinctrl_mii_pccard: mii_pccard {
+ function = "mii_pccard";
+ groups = "group1";
+ };
+
+ pinctrl_pci: pci {
+ function = "pci";
+ groups = "group2";
+ };
+
+ pinctrl_spi_master_uart: spi_master_uart {
+ function = "spi_master_uart";
+ groups = "group1";
+ };
+
+ pinctrl_ext_mii: ext_mii {
+ function = "ext_mii";
+ groups = "group0", "group3";
+ };
+
+ pinctrl_utopia: utopia {
+ function = "utopia";
+ groups = "group0", "group1", "group3";
+ };
};
lsspi: spi@fffe0c00 {
aliases {
pflash = &pflash;
- gpio0 = &gpio0;
- gpio1 = &gpio1;
+ pinctrl = &pinctrl;
spi0 = &lsspi;
};
interrupts = <20>, <21>;
};
- gpio1: gpio-controller@fffe0080 {
- compatible = "brcm,bcm6345-gpio";
- reg = <0xfffe0080 4>, <0xfffe0088 4>;
+ pinctrl: pin-controller@fffe0080 {
+ compatible = "brcm,bcm6358-pinctrl";
+ reg = <0xfffe0080 0x8>,
+ <0xfffe0088 0x8>;
+ reg-names = "dirout", "dat", "mode";
+ brcm,gpiomode = <&gpiomode>;
gpio-controller;
#gpio-cells = <2>;
- ngpios = <8>;
-
interrupts-extended = <&ext_intc1 0 0>,
<&ext_intc1 1 0>,
<&ext_intc0 0 0>,
<&ext_intc0 1 0>,
<&ext_intc0 2 0>,
<&ext_intc0 3 0>;
- interrupt-names = "gpio0", "gpio1", "gpio2", "gpio3",
- "gpio4", "gpio5";
+ interrupt-names = "gpio32", "gpio33", "gpio34", "gpio35",
+ "gpio36", "gpio37";
+
+ pinctrl_ebi_cs: ebi_cs {
+ function = "ebi_cs";
+ groups = "ebi_cs_grp";
+ };
+
+ pinctrl_uart1: uart1 {
+ function = "uart1";
+ groups = "uart1_grp";
+ };
+
+ pinctrl_serial_led: serial_led {
+ function = "serial_led";
+ groups = "serial_led_grp";
+ };
+
+ pinctrl_legacy_led: legacy_led {
+ function = "legacy_led";
+ groups = "legacy_led_grp";
+ };
+
+ pinctrl_led: led {
+ function = "led";
+ groups = "led_grp";
+ };
+
+ pinctrl_spi_cs_23: spi_cs {
+ function = "spi_cs";
+ groups = "spi_cs_grp";
+ };
+
+ pinctrl_utopia: utopia {
+ function = "utopia";
+ groups = "utopia_grp";
+ };
+
+ pinctrl_pwm_syn_clk: pwm_syn_clk {
+ function = "pwm_syn_clk";
+ groups = "pwm_syn_clk_grp";
+ };
+
+ pinctrl_sys_irq: sys_irq {
+ function = "sys_irq";
+ groups = "sys_irq_grp";
+ };
};
- gpio0: gpio-controller@fffe0084 {
- compatible = "brcm,bcm6345-gpio";
- reg = <0xfffe0084 4>, <0xfffe008c 4>;
-
- gpio-controller;
- #gpio-cells = <2>;
+ gpiomode: gpiomode@fffe0098 {
+ compatible = "brcm,bcm6358-gpiomode", "syscon";
+ reg = <0xfffe0098 0x4>;
};
lsspi: spi@fffe0800 {
compatible = "brcm,bcm6362";
aliases {
- gpio0 = &gpio0;
- gpio1 = &gpio1;
+ pinctrl = &pinctrl;
spi0 = &lsspi;
spi1 = &hsspi;
};
interrupts = <2>, <3>;
};
- gpio1: gpio-controller@10000080 {
- compatible = "brcm,bcm6345-gpio";
- reg = <0x10000080 4>, <0x10000088 4>;
-
- gpio-controller;
- #gpio-cells = <2>;
-
- ngpios = <16>;
- };
-
- gpio0: gpio-controller@10000084 {
- compatible = "brcm,bcm6345-gpio";
- reg = <0x10000084 4>, <0x1000008c 4>;
+ pinctrl: pin-controller@10000080 {
+ compatible = "brcm,bcm6362-pinctrl";
+ reg = <0x10000080 0x8>,
+ <0x10000088 0x8>,
+ <0x10000090 0x4>,
+ <0x10000098 0x4>,
+ <0x1000009c 0x4>,
+ <0x100000b8 0x4>;
+ reg-names = "dirout", "dat", "led",
+ "mode", "ctrl", "basemode";
gpio-controller;
#gpio-cells = <2>;
interrupts = <0 0>, <1 0>, <2 0>, <3 0>;
interrupt-names = "gpio24", "gpio25",
"gpio26", "gpio27";
+
+ pinctrl_usb_device_led: usb_device_led {
+ function = "usb_device_led";
+ pins = "gpio0";
+ };
+
+ pinctrl_sys_irq: sys_irq {
+ function = "sys_irq";
+ pins = "gpio1";
+ };
+
+ pinctrl_serial_led: serial_led {
+ pinctrl_serial_led_clk: serial_led_clk {
+ function = "serial_led_clk";
+ pins = "gpio2";
+ };
+
+ pinctrl_serial_led_data: serial_led_data {
+ function = "serial_led_data";
+ pins = "gpio3";
+ };
+ };
+
+ pinctrl_robosw_led_data: robosw_led_data {
+ function = "robosw_led_data";
+ pins = "gpio4";
+ };
+
+ pinctrl_robosw_led_clk: robosw_led_clk {
+ function = "robosw_led_clk";
+ pins = "gpio5";
+ };
+
+ pinctrl_robosw_led0: robosw_led0 {
+ function = "robosw_led0";
+ pins = "gpio6";
+ };
+
+ pinctrl_robosw_led1: robosw_led1 {
+ function = "robosw_led1";
+ pins = "gpio7";
+ };
+
+ pinctrl_inet_led: inet_led {
+ function = "inet_led";
+ pins = "gpio8";
+ };
+
+ pinctrl_spi_cs2: spi_cs2 {
+ function = "spi_cs2";
+ pins = "gpio9";
+ };
+
+ pinctrl_spi_cs3: spi_cs3 {
+ function = "spi_cs3";
+ pins = "gpio10";
+ };
+
+ pinctrl_ntr_pulse: ntr_pulse {
+ function = "ntr_pulse";
+ pins = "gpio11";
+ };
+
+ pinctrl_uart1_scts: uart1_scts {
+ function = "uart1_scts";
+ pins = "gpio12";
+ };
+
+ pinctrl_uart1_srts: uart1_srts {
+ function = "uart1_srts";
+ pins = "gpio13";
+ };
+
+
+ pinctrl_uart1: uart1 {
+ pinctrl_uart1_sdin: uart1_sdin {
+ function = "uart1_sdin";
+ pins = "gpio14";
+ };
+
+ pinctrl_uart1_sdout: uart1_sdout {
+ function = "uart1_sdout";
+ pins = "gpio15";
+ };
+ };
+
+ pinctrl_adsl_spi: adsl_spi {
+ pinctrl_adsl_spi_miso: adsl_spi_miso {
+ function = "adsl_spi_miso";
+ pins = "gpio16";
+ };
+
+ pinctrl_adsl_spi_mosi: adsl_spi_mosi {
+ function = "adsl_spi_mosi";
+ pins = "gpio17";
+ };
+
+ pinctrl_adsl_spi_clk: adsl_spi_clk {
+ function = "adsl_spi_clk";
+ pins = "gpio18";
+ };
+
+ pinctrl_adsl_spi_cs: adsl_spi_cs {
+ function = "adsl_spi_cs";
+ pins = "gpio19";
+ };
+ };
+
+ pinctrl_ephy0_led: ephy0_led {
+ function = "ephy0_led";
+ pins = "gpio20";
+ };
+
+ pinctrl_ephy1_led: ephy1_led {
+ function = "ephy1_led";
+ pins = "gpio21";
+ };
+
+ pinctrl_ephy2_led: ephy2_led {
+ function = "ephy2_led";
+ pins = "gpio22";
+ };
+
+ pinctrl_ephy3_led: ephy3_led {
+ function = "ephy3_led";
+ pins = "gpio23";
+ };
+
+ pinctrl_ext_irq0: ext_irq0 {
+ function = "ext_irq0";
+ pins = "gpio24";
+ };
+
+ pinctrl_ext_irq1: ext_irq1 {
+ function = "ext_irq1";
+ pins = "gpio25";
+ };
+
+ pinctrl_ext_irq2: ext_irq2 {
+ function = "ext_irq2";
+ pins = "gpio26";
+ };
+
+ pinctrl_ext_irq3: ext_irq3 {
+ function = "ext_irq3";
+ pins = "gpio27";
+ };
+
+ pinctrl_nand: nand {
+ function = "nand";
+ group = "nand_grp";
+ };
};
lsspi: spi@10000800 {
aliases {
pflash = &pflash;
- gpio0 = &gpio0;
- gpio1 = &gpio1;
+ pinctrl = &pinctrl;
spi0 = &lsspi;
};
interrupts = <2>, <3>;
};
- gpio1: gpio-controller@10000080 {
- compatible = "brcm,bcm6345-gpio";
- reg = <0x10000080 4>, <0x10000088 4>;
+ pinctrl: pin-controller@10000080 {
+ compatible = "brcm,bcm6368-pinctrl";
+ reg = <0x10000080 0x8>,
+ <0x10000088 0x8>,
+ <0x10000098 0x4>;
+ reg-names = "dirout", "dat", "mode";
+ brcm,gpiobasemode = <&gpiobasemode>;
gpio-controller;
#gpio-cells = <2>;
- ngpios = <6>;
-
interrupts-extended = <&ext_intc1 0 0>,
<&ext_intc1 1 0>,
<&ext_intc0 0 0>,
<&ext_intc0 1 0>,
<&ext_intc0 2 0>,
<&ext_intc0 3 0>;
- interrupt-names = "gpio0", "gpio1", "gpio2", "gpio3",
- "gpio4", "gpio5";
- };
+ interrupt-names = "gpio32", "gpio33", "gpio34", "gpio35",
+ "gpio36", "gpio37";
- gpio0: gpio-controller@10000084 {
- compatible = "brcm,bcm6345-gpio";
- reg = <0x10000084 4>, <0x1000008c 4>;
+ pinctrl_analog_afe_0: analog_afe_0 {
+ function = "analog_afe_0";
+ pins = "gpio0";
+ };
- gpio-controller;
- #gpio-cells = <2>;
+ pinctrl_analog_afe_1: analog_afe_1 {
+ function = "analog_afe_1";
+ pins = "gpio1";
+ };
+
+ pinctrl_sys_irq: sys_irq {
+ function = "sys_irq";
+ pins = "gpio2";
+ };
+
+ pinctrl_serial_led: serial_led {
+ pinctrl_serial_led_data: serial_led_data {
+ function = "serial_led_data";
+ pins = "gpio3";
+ };
+
+ pinctrl_serial_led_clk: serial_led_clk {
+ function = "serial_led_clk";
+ pins = "gpio4";
+ };
+ };
+
+ pinctrl_inet_led: inet_led {
+ function = "inet_led";
+ pins = "gpio5";
+ };
+
+ pinctrl_ephy0_led: ephy0_led {
+ function = "ephy0_led";
+ pins = "gpio6";
+ };
+
+ pinctrl_ephy1_led: ephy1_led {
+ function = "ephy1_led";
+ pins = "gpio7";
+ };
+
+ pinctrl_ephy2_led: ephy2_led {
+ function = "ephy2_led";
+ pins = "gpio8";
+ };
+
+ pinctrl_ephy3_led: ephy3_led {
+ function = "ephy3_led";
+ pins = "gpio9";
+ };
+
+ pinctrl_robosw_led_data: robosw_led_data {
+ function = "robosw_led_data";
+ pins = "gpio10";
+ };
+
+ pinctrl_robosw_led_clk: robosw_led_clk {
+ function = "robosw_led_clk";
+ pins = "gpio11";
+ };
+
+ pinctrl_robosw_led0: robosw_led0 {
+ function = "robosw_led0";
+ pins = "gpio12";
+ };
+
+ pinctrl_robosw_led1: robosw_led1 {
+ function = "robosw_led1";
+ pins = "gpio13";
+ };
+
+ pinctrl_usb_device_led: usb_device_led {
+ function = "usb_device_led";
+ pins = "gpio14";
+ };
+
+ pinctrl_pci: pci {
+ pinctrl_pci_req1: pci_req1 {
+ function = "pci_req1";
+ pins = "gpio16";
+ };
+
+ pinctrl_pci_gnt1: pci_gnt1 {
+ function = "pci_gnt1";
+ pins = "gpio17";
+ };
+
+ pinctrl_pci_intb: pci_intb {
+ function = "pci_intb";
+ pins = "gpio18";
+ };
+
+ pinctrl_pci_req0: pci_req0 {
+ function = "pci_req0";
+ pins = "gpio19";
+ };
+
+ pinctrl_pci_gnt0: pci_gnt0 {
+ function = "pci_gnt0";
+ pins = "gpio20";
+ };
+ };
+
+ pinctrl_pcmcia: pcmcia {
+ pinctrl_pcmcia_cd1: pcmcia_cd1 {
+ function = "pcmcia_cd1";
+ pins = "gpio22";
+ };
+
+ pinctrl_pcmcia_cd2: pcmcia_cd2 {
+ function = "pcmcia_cd2";
+ pins = "gpio23";
+ };
+
+ pinctrl_pcmcia_vs1: pcmcia_vs1 {
+ function = "pcmcia_vs1";
+ pins = "gpio24";
+ };
+
+ pinctrl_pcmcia_vs2: pcmcia_vs2 {
+ function = "pcmcia_vs2";
+ pins = "gpio25";
+ };
+ };
+
+ pinctrl_ebi_cs2: ebi_cs2 {
+ function = "ebi_cs2";
+ pins = "gpio26";
+ };
+
+ pinctrl_ebi_cs3: ebi_cs3 {
+ function = "ebi_cs2";
+ pins = "gpio27";
+ };
+
+ pinctrl_spi_cs2: spi_cs2 {
+ function = "spi_cs2";
+ pins = "gpio28";
+ };
+
+ pinctrl_spi_cs3: spi_cs3 {
+ function = "spi_cs3";
+ pins = "gpio29";
+ };
+
+ pinctrl_spi_cs4: spi_cs4 {
+ function = "spi_cs4";
+ pins = "gpio30";
+ };
+
+ pinctrl_spi_cs5: spi_cs5 {
+ function = "spi_cs5";
+ pins = "gpio31";
+ };
+
+ pinctrl_uart1: uart1 {
+ function = "uart1";
+ group = "uart1_grp";
+ };
+ };
+
+ gpiobasemode: gpiobasemode@100000b8 {
+ compatible = "brcm,bcm6368-gpiobasemode", "syscon";
+ reg = <0x100000b8 0x4>;
};
lsspi: spi@10000800 {
wps {
label = "wps";
- gpios = <&gpio1 1 1>;
+ gpios = <&pinctrl 33 1>;
linux,code = <KEY_WPS_BUTTON>;
};
reset {
label = "reset";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_RESTART>;
};
};
inet {
label = "96318REF:green:inet";
- gpios = <&gpio0 8 1>;
+ gpios = <&pinctrl 8 1>;
};
inet_fail {
label = "96318REF:red:inet-fail";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
};
post_failed {
label = "96318REF:red:post-failed";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
};
};
linux,part-probe = "bcm63xxpart";
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_pwron>;
+};
wps {
label = "wps";
- gpios = <&gpio1 1 1>;
+ gpios = <&pinctrl 33 1>;
linux,code = <KEY_WPS_BUTTON>;
};
reset {
label = "reset";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_RESTART>;
};
};
inet {
label = "96318REF_P300:green:inet";
- gpios = <&gpio0 8 1>;
+ gpios = <&pinctrl 8 1>;
};
inet_fail {
label = "96318REF_P300:red:inet-fail";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
};
post_failed {
label = "96318REF_P300:red:post-failed";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
usb_pwron {
label = "96318REF_P300::usb-pwron";
- gpios = <&gpio0 13 1>;
+ gpios = <&pinctrl 13 1>;
default-state = "on";
};
};
linux,part-probe = "bcm63xxpart";
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_pwron>;
+};
reset {
label = "reset";
- gpios = <&gpio1 0 0>;
+ gpios = <&pinctrl 32 0>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
- gpios = <&gpio1 1 0>;
+ gpios = <&pinctrl 33 0>;
linux,code = <KEY_WPS_BUTTON>;
};
};
reset {
label = "reset";
- gpios = <&gpio1 0 0>;
+ gpios = <&pinctrl 32 0>;
linux,code = <KEY_RESTART>;
};
};
usb1 {
label = "963269BHR:green:usb1";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
};
usb2 {
label = "963269BHR:green:usb2";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
};
};
};
inet {
label = "963281TAN::internet";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
power {
label = "963281TAN::power";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
default-state = "on";
};
inet_fail {
label = "963281TAN::internet-fail";
- gpios = <&gpio0 7 1>;
+ gpios = <&pinctrl 7 1>;
};
power_fail {
label = "963281TAN::power-fail";
- gpios = <&gpio0 8 1>;
+ gpios = <&pinctrl 8 1>;
};
wps {
label = "963281TAN::wps";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
};
dsl {
label = "963281TAN::dsl";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
};
};
inet_fail {
label = "96328avng::internet-fail";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
dsl {
label = "96328avng::dsl";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
power {
label = "96328avng::power";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
default-state = "on";
};
power_fail {
label = "96328avng::power-fail";
- gpios = <&gpio0 8 1>;
+ gpios = <&pinctrl 8 1>;
};
wps {
label = "96328avng::wps";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
};
inet {
label = "96328avng::internet";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
};
};
linux,part-probe = "bcm63xxpart";
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_port1_device>;
+};
reset {
label = "reset";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "96348GW-10:green:power";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
default-state = "on";
};
stop_green {
label = "96348GW-10:green:stop";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
adsl_fail_green {
label = "96348GW-10:green:adsl-fail";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
ppp_green {
label = "96348GW-10:green:ppp";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
ppp_fail_green {
label = "96348GW-10:green:ppp-fail";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
};
};
linux,part-probe = "bcm63xxpart";
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii &pinctrl_mii_pccard>;
+};
reset {
label = "reset";
- gpios = <&gpio1 1 1>;
+ gpios = <&pinctrl 33 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "96348GW-11:green:power";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
default-state = "on";
};
stop_green {
label = "96348GW-11:green:stop";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
adsl_fail_green {
label = "96348GW-11:green:adsl-fail";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
ppp_green {
label = "96348GW-11:green:ppp";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
ppp_fail_green {
label = "96348GW-11:green:ppp-fail";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
};
};
linux,part-probe = "bcm63xxpart";
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii &pinctrl_mii_pccard>;
+};
reset {
label = "reset";
- gpios = <&gpio1 4 1>;
+ gpios = <&pinctrl 36 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "96348GW:green:power";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
default-state = "on";
};
stop_green {
label = "96348GW:green:stop";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
adsl_fail_green {
label = "96348GW:green:adsl-fail";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
ppp_green {
label = "96348GW:green:ppp";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
ppp_fail_green {
label = "96348GW:green:ppp-fail";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
};
};
linux,part-probe = "bcm63xxpart";
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii>;
+};
power_green {
label = "96348R:green:power";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
default-state = "on";
};
stop_green {
label = "96348R:green:stop";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
adsl_fail_green {
label = "96348R:green:adsl-fail";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
ppp_green {
label = "96348R:green:ppp";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
ppp_fail_green {
label = "96348R:green:ppp-fail";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
};
};
linux,part-probe = "bcm63xxpart";
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci>;
+};
power_green {
label = "96358VW:green:power";
- gpios = <&gpio0 4 0>;
+ gpios = <&pinctrl 4 0>;
default-state = "on";
};
stop_green {
label = "96358VW:green:stop";
- gpios = <&gpio0 5 0>;
+ gpios = <&pinctrl 5 0>;
};
adsl_fail_green {
label = "96358VW:green:adsl-fail";
- gpios = <&gpio0 15 1>;
+ gpios = <&pinctrl 15 1>;
};
ppp_green {
label = "96358VW:green:ppp";
- gpios = <&gpio0 22 1>;
+ gpios = <&pinctrl 22 1>;
};
ppp_fail_green {
label = "96358VW:green:ppp-fail";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
};
};
};
stop_green {
label = "96358VW2:green:stop";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
power_green {
label = "96358VW2:green:power";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
default-state = "on";
};
adsl_green {
label = "96358VW2:green:adsl";
- gpios = <&gpio0 22 1>;
+ gpios = <&pinctrl 22 1>;
};
ppp_fail_green {
label = "96358VW2:green:ppp-fail";
- gpios = <&gpio0 23 0>;
+ gpios = <&pinctrl 23 0>;
};
};
};
dsl_green {
label = "96368MVNgr:green:adsl";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
inet_fail_green {
label = "96368MVNgr:green:inet-fail";
- gpios = <&gpio0 3 0>;
+ gpios = <&pinctrl 3 0>;
};
inet_green {
label = "96368MVNgr:green:inet";
- gpios = <&gpio0 5 0>;
+ gpios = <&pinctrl 5 0>;
};
power_green {
label = "96368MVNgr:green:power";
- gpios = <&gpio0 22 0>;
+ gpios = <&pinctrl 22 0>;
default-state = "on";
};
wps_green {
label = "96368MVNgr:green:wps";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
};
};
};
linux,part-probe = "bcm63xxpart";
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci>;
+};
dsl_green {
label = "96368MVWG:green:adsl";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
ppp_green {
label = "96368MVWG:green:ppp";
- gpios = <&gpio0 5 0>;
+ gpios = <&pinctrl 5 0>;
};
power_green {
label = "96368MVWG:green:power";
- gpios = <&gpio0 22 0>;
+ gpios = <&pinctrl 22 0>;
default-state = "on";
};
wps_green {
label = "96368MVWG:green:wps";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
};
ppp_fail_red {
label = "96368MVWG:red:ppp-fail";
- gpios = <&gpio0 31 0>;
+ gpios = <&pinctrl 31 0>;
};
};
};
linux,part-probe = "bcm63xxpart";
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci>;
+};
reset {
label = "reset";
- gpios = <&gpio1 4 1>;
+ gpios = <&pinctrl 36 1>;
linux,code = <KEY_RESTART>;
};
};
phone_green {
label = "CPVA502+:green:phone";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
};
link_amber {
label = "CPVA502+:amber:link";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
};
};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii>;
+};
reset {
label = "reset";
- gpios = <&gpio1 4 1>;
+ gpios = <&pinctrl 36 1>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
- gpios = <&gpio1 5 0>;
+ gpios = <&pinctrl 37 0>;
linux,code = <KEY_WPS_BUTTON>;
};
};
eth_green {
label = "CPVA642:green:ether";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
phone2_green {
label = "CPVA642:green:phone2";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
usb_green {
label = "CPVA642:green:usb";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
phone1_green {
label = "CPVA642:green:phone1";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
wifi_red {
label = "CPVA642:red:wifi";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
};
link_red {
label = "CPVA642:red:link";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
};
link_green {
label = "CPVA642:green:link";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
};
power_green {
label = "CPVA642:green:power";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
default-state = "on";
};
power_red {
label = "CPVA642:red:power";
- gpios = <&gpio0 14 1>;
+ gpios = <&pinctrl 14 1>;
};
wifi_green {
label = "CPVA642:green:wifi";
- gpios = <&gpio0 28 0>;
+ gpios = <&pinctrl 28 0>;
};
};
};
reset {
label = "reset";
- gpios = <&gpio1 1 1>;
+ gpios = <&pinctrl 33 1>;
linux,code = <KEY_RESTART>;
};
wlan {
label = "wlan";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_WLAN>;
};
wps {
label = "wps";
- gpios = <&gpio1 3 1>;
+ gpios = <&pinctrl 35 1>;
linux,code = <KEY_WPS_BUTTON>;
};
};
power_green {
label = "96348A-122:green:power";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
default-state = "on";
};
alarm_red {
label = "96348A-122:red:alarm";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
wps_green {
label = "96348A-122:green:wps";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
};
};
};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii>;
+};
#size-cells = <0>;
compatible = "spi-gpio";
- gpio-mosi = <&gpio0 7 0>;
- gpio-sck = <&gpio0 6 0>;
+ gpio-mosi = <&pinctrl 7 0>;
+ gpio-sck = <&pinctrl 6 0>;
num-chipselects = <0>;
hc595: gpio-spi-controller@0 {
reset {
label = "reset";
- gpios = <&gpio1 3 1>;
+ gpios = <&pinctrl 35 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "CT6373-1:green:power";
- gpios = <&gpio0 0 0>;
+ gpios = <&pinctrl 0 0>;
default-state = "on";
};
usb_green {
label = "CT6373-1:green:usb";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
wlan_green {
label = "CT6373-1:green:wlan";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
};
dsl_green {
label = "CT6373-1:green:adsl";
reset {
label = "reset";
- gpios = <&gpio1 1 1>;
+ gpios = <&pinctrl 33 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "CT536_CT5621:green:power";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
default-state = "on";
};
adsl_fail_green {
label = "CT536_CT5621:green:adsl-fail";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
};
};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii &pinctrl_mii_pccard>;
+};
reset {
label = "reset";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "96348W3:green:power";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
default-state = "on";
};
status {
label = "96348W3:red:power";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
inet_green {
label = "96348W3::adsl";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
inet_red {
label = "96348W3::internet";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
};
};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii>;
+};
reset {
label = "reset";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "96348GW-10:green:power";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
default-state = "on";
};
stop_green {
label = "96348GW-10:green:stop";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
adsl_fail_green {
label = "96348GW-10:green:adsl-fail";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
ppp_green {
label = "96348GW-10:green:ppp";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
ppp_fail_green {
label = "96348GW-10:green:ppp-fail";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
};
};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii &pinctrl_mii_pccard>;
+};
wlan {
label = "wlan";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
linux,code = <KEY_WLAN>;
};
reset {
label = "reset";
- gpios = <&gpio0 12 1>;
+ gpios = <&pinctrl 12 1>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
- gpios = <&gpio1 3 1>;
+ gpios = <&pinctrl 35 1>;
linux,code = <KEY_WPS_BUTTON>;
};
};
dsl_green {
label = "DGND3700v1_3800B:green:dsl";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
inet_red {
label = "DGND3700v1_3800B:red:inet";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
inet_green {
label = "DGND3700v1_3800B:green:inet";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
wps_green {
label = "DGND3700v1_3800B:green:wps";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
usbfront_green {
label = "DGND3700v1_3800B:green:usb-front";
- gpios = <&gpio0 13 1>;
+ gpios = <&pinctrl 13 1>;
};
usbback_green {
label = "DGND3700v1_3800B:green:usb-back";
- gpios = <&gpio0 14 1>;
+ gpios = <&pinctrl 14 1>;
};
power_red {
label = "DGND3700v1_3800B:red:power";
- gpios = <&gpio0 22 1>;
+ gpios = <&pinctrl 22 1>;
};
lan_green {
label = "DGND3700v1_3800B:green:lan";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
};
power_green {
label = "DGND3700v1_3800B:green:power";
- gpios = <&gpio0 24 1>;
+ gpios = <&pinctrl 24 1>;
default-state = "on";
};
wifi2g_green {
label = "DGND3700v1_3800B:green:wifi2g";
- gpios = <&gpio0 26 1>;
+ gpios = <&pinctrl 26 1>;
};
wifi5g_blue {
label = "DGND3700v1_3800B:blue:wifi5g";
- gpios = <&gpio0 27 1>;
+ gpios = <&pinctrl 27 1>;
};
};
};
label = "nvram";
reg = <0x1fe0000 0x20000>;
};
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci>;
};
reset {
label = "reset";
- gpios = <&gpio0 7 1>;
+ gpios = <&pinctrl 7 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "D-4P-W:green:power";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
default-state = "on";
};
status {
label = "D-4P-W::status";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
inet_green {
label = "D-4P-W:green:internet";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
inet_red {
label = "D-4P-W:red:internet";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
};
};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii>;
+};
stop_green {
label = "96358VW2:green:stop";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
power_green {
label = "96358VW2:green:power";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
default-state = "on";
};
adsl_green {
label = "96358VW2:green:adsl";
- gpios = <&gpio0 22 1>;
+ gpios = <&pinctrl 22 1>;
};
ppp_fail_green {
label = "96358VW2:green:ppp-fail";
- gpios = <&gpio0 23 0>;
+ gpios = <&pinctrl 23 0>;
};
};
};
reset {
label = "reset";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_RESTART>;
};
};
inet_green {
label = "dsl-274xb:green:internet";
- gpios = <&gpio0 2 0>;
+ gpios = <&pinctrl 2 0>;
};
power_red {
label = "dsl-274xb:red:power";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
power_green {
label = "dsl-274xb:green:power";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
default-state = "on";
};
dsl_green {
label = "dsl-274xb:green:adsl";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
};
inet_red {
label = "dsl-274xb:red:internet";
- gpios = <&gpio0 10 0>;
+ gpios = <&pinctrl 10 0>;
};
};
};
wifi {
label = "wifi";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
linux,code = <KEY_WLAN>;
};
reset {
label = "reset";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
- gpios = <&gpio0 24 1>;
+ gpios = <&pinctrl 24 1>;
linux,code = <KEY_WPS_BUTTON>;
};
};
inet_red {
label = "dsl-274xb:red:internet";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
dsl_green {
label = "dsl-274xb:green:dsl";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
power_green {
label = "dsl-274xb:green:power";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
default-state = "on";
};
power_red {
label = "dsl-274xb:red:power";
- gpios = <&gpio0 8 1>;
+ gpios = <&pinctrl 8 1>;
};
wps_blue {
label = "dsl-274xb:blue:wps";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
};
inet_green {
label = "dsl-274xb:green:internet";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
};
};
wifi {
label = "wifi";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
linux,code = <KEY_WLAN>;
};
wps {
label = "wps";
- gpios = <&gpio1 1 1>;
+ gpios = <&pinctrl 33 1>;
linux,code = <KEY_WPS_BUTTON>;
};
reset {
label = "reset";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "dsl-275xb:green:power";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
default-state = "on";
};
inet_green {
label = "dsl-275xb:green:inet";
- gpios = <&gpio0 8 1>;
+ gpios = <&pinctrl 8 1>;
};
inet_red {
label = "dsl-275xb:red:inet-fail";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
};
power_red {
label = "dsl-275xb:red:post-failed";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
wps_blue {
label = "dsl-275xb:blue:wps";
- gpios = <&gpio0 16 1>;
+ gpios = <&pinctrl 16 1>;
};
dsl_green {
label = "dsl-275xb:green:dsl";
- gpios = <&gpio0 17 1>;
+ gpios = <&pinctrl 17 1>;
};
usb_green {
/* not user controllable? */
label = "dsl-275xb:green:usb";
- gpios = <&gpio1 17 1>;
+ gpios = <&pinctrl 49 1>;
};
};
};
reg = <0x410000 0x3f0000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii>;
+};
reset {
label = "reset";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_RESTART>;
};
};
voip {
label = "DVAG3810BN::voip";
- gpios = <&gpio0 1 0>;
+ gpios = <&pinctrl 1 0>;
};
power {
label = "DVAG3810BN::power";
- gpios = <&gpio0 4 0>;
+ gpios = <&pinctrl 4 0>;
default-state = "on";
};
stop {
label = "DVAG3810BN::stop";
- gpios = <&gpio0 5 0>;
+ gpios = <&pinctrl 5 0>;
};
dsl {
label = "DVAG3810BN::dsl";
- gpios = <&gpio0 22 1>;
+ gpios = <&pinctrl 22 1>;
};
inet {
label = "DVAG3810BN::internet";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
};
};
};
reset {
label = "reset";
- gpios = <&gpio0 25 1>;
+ gpios = <&pinctrl 25 1>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
- gpios = <&gpio0 26 1>;
+ gpios = <&pinctrl 26 1>;
linux,code = <KEY_WPS_BUTTON>;
};
};
voip1_green {
label = "EVG2000:green:voip1";
- gpios = <&gpio0 14 1>;
+ gpios = <&pinctrl 14 1>;
};
voip2_green {
label = "EVG2000:green:voip2";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
inet_red {
label = "EVG2000:red:inet";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
inet_green {
label = "EVG2000:green:inet";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
usb_green {
label = "EVG2000:green:usb";
- gpios = <&gpio0 15 1>;
+ gpios = <&pinctrl 15 1>;
};
power_green {
label = "EVG2000:green:power";
- gpios = <&gpio0 22 1>;
+ gpios = <&pinctrl 22 1>;
default-state = "on";
};
power_red {
label = "EVG2000:red:power";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
};
lan_green {
label = "EVG2000:green:lan";
- gpios = <&gpio0 24 1>;
+ gpios = <&pinctrl 24 1>;
};
wireless_green {
label = "EVG2000:green:wireless";
- gpios = <&gpio0 26 1>;
+ gpios = <&pinctrl 26 1>;
};
wan_green {
label = "EVG2000:green:wan";
- gpios = <&gpio0 27 1>;
+ gpios = <&pinctrl 27 1>;
};
};
};
reg = <0x00fe0000 0x00020000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci>;
+};
reset {
label = "reset";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "96348GW-10:green:power";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
default-state = "on";
};
stop_green {
label = "96348GW-10:green:stop";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
adsl_fail_green {
label = "96348GW-10:green:adsl-fail";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
ppp_green {
label = "96348GW-10:green:ppp";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
ppp_fail_green {
label = "96348GW-10:green:ppp-fail";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
};
};
reg = <0x3e0000 0x020000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii &pinctrl_mii_pccard>;
+};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii &pinctrl_mii_pccard>;
+};
reset {
label = "reset";
- gpios = <&gpio0 24 1>;
+ gpios = <&pinctrl 24 1>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
- gpios = <&gpio0 25 1>;
+ gpios = <&pinctrl 25 1>;
linux,code = <KEY_WPS_BUTTON>;
};
};
power_orange {
label = "fast2504n:orange:power";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
power_green {
label = "fast2504n:green:power";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
default-state = "on";
};
inet_red {
label = "fast2504n:red:internet";
- gpios = <&gpio0 26 1>;
+ gpios = <&pinctrl 26 1>;
};
ok_green {
label = "fast2504n:green:ok";
- gpios = <&gpio0 28 1>;
+ gpios = <&pinctrl 28 1>;
};
ok_orange {
label = "fast2504n:orange:ok";
- gpios = <&gpio0 29 1>;
+ gpios = <&pinctrl 29 1>;
};
wlan_orangee {
label = "fast2504n:orange:wlan";
- gpios = <&gpio0 30 1>;
+ gpios = <&pinctrl 30 1>;
};
};
};
reset {
label = "reset";
- gpios = <&gpio1 1 1>;
+ gpios = <&pinctrl 33 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "F@ST2604:green:power";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
default-state = "on";
};
power_red {
label = "F@ST2604:red:power";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
inet_red {
label = "F@ST2604:red:inet";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
wps_green {
label = "F@ST2604:green:wps";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
};
};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii>;
+};
wlan {
label = "wlan";
- gpios = <&gpio0 1 0>;
+ gpios = <&pinctrl 1 0>;
linux,code = <KEY_WLAN>;
};
wps {
label = "wps";
- gpios = <&gpio1 1 1>;
+ gpios = <&pinctrl 33 1>;
linux,code = <KEY_WPS_BUTTON>;
};
reset {
label = "reset";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_RESTART>;
};
};
wps_green {
label = "F@ST2704N:green:wps";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
lan1_green {
label = "F@ST2704N:green:lan1";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
lan2_green {
label = "F@ST2704N:green:lan2";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
lan3_green {
label = "F@ST2704N:green:lan3";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
};
lan4_green {
label = "F@ST2704N:green:lan4";
- gpios = <&gpio0 7 1>;
+ gpios = <&pinctrl 7 1>;
};
inet_green {
label = "F@ST2704N:green:inet";
- gpios = <&gpio0 8 1>;
+ gpios = <&pinctrl 8 1>;
};
inet_red {
label = "F@ST2704N:red:inet";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
};
dsl_green {
label = "F@ST2704N:green:dsl";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
};
power_red {
label = "F@ST2704N:red:power";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
power_green {
label = "F@ST2704N:green:power";
- gpios = <&gpio1 15 1>;
+ gpios = <&pinctrl 47 1>;
default-state = "on";
};
usb_green {
label = "F@ST2704N:green:usb";
- gpios = <&gpio1 17 1>;
+ gpios = <&pinctrl 49 1>;
};
};
};
rfkill {
label = "rfkill";
- gpios = <&gpio0 15 1>;
+ gpios = <&pinctrl 15 1>;
linux,code = <KEY_WLAN>;
};
reset {
label = "reset";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
- gpios = <&gpio0 24 1>;
+ gpios = <&pinctrl 24 1>;
linux,code = <KEY_WPS_BUTTON>;
};
};
usb_green {
label = "F@ST2704V2:green:usb";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
inet_red {
label = "F@ST2704V2:red:inet";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
dsl_green {
label = "F@ST2704V2:green:dsl";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
power_green {
label = "F@ST2704V2:green:power";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
default-state = "on";
};
power_red {
label = "F@ST2704V2:red:power";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
wps_green {
label = "F@ST2704V2:green:wps";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
};
inet_green {
label = "F@ST2704V2:green:inet";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
};
};
reset {
label = "reset";
- gpios = <&gpio1 4 1>;
+ gpios = <&pinctrl 36 1>;
linux,code = <KEY_RESTART>;
};
};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii>;
+};
reset {
label = "reset";
- gpios = <&gpio1 4 1>;
+ gpios = <&pinctrl 36 1>;
linux,code = <KEY_RESTART>;
};
};
line1_green {
label = "GW6200:green:line1";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
line2_green {
label = "GW6200:green:line2";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
line3_green {
label = "GW6200:green:line3";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
};
tel_green {
label = "GW6200:green:tel";
- gpios = <&gpio0 7 1>;
+ gpios = <&pinctrl 7 1>;
};
};
};
reg = <0x7f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii &pinctrl_mii_pccard>;
+};
reset {
label = "reset";
- gpios = <&gpio1 5 1>;
+ gpios = <&pinctrl 37 1>;
linux,code = <KEY_RESTART>;
};
};
inet_green {
label = "HW520:green:net";
- gpios = <&gpio1 0 1>;
+ gpios = <&pinctrl 32 1>;
};
};
};
rfkill {
label = "rfkill";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
linux,code = <KEY_RFKILL>;
};
reset {
label = "reset";
- gpios = <&gpio1 5 1>;
+ gpios = <&pinctrl 37 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "HW553:blue:power";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
default-state = "on";
};
power_red {
label = "HW553:red:power";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
hspa_red {
label = "HW553:red:hspa";
- gpios = <&gpio0 12 1>;
+ gpios = <&pinctrl 12 1>;
};
hspa_blue {
label = "HW553:blue:hspa";
- gpios = <&gpio0 13 1>;
+ gpios = <&pinctrl 13 1>;
};
lan_red {
label = "HW553:red:lan";
- gpios = <&gpio0 22 1>;
+ gpios = <&pinctrl 22 1>;
};
lan_blue {
label = "HW553:blue:lan";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
};
wifi_red {
label = "HW553:red:wifi";
- gpios = <&gpio0 25 1>;
+ gpios = <&pinctrl 25 1>;
};
dsl_red {
label = "HW553:red:adsl";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
};
dsl_blue {
label = "HW553:blue:adsl";
- gpios = <&gpio1 3 1>;
+ gpios = <&pinctrl 35 1>;
};
};
};
help {
label = "help";
- gpios = <&gpio0 8 1>;
+ gpios = <&pinctrl 8 1>;
linux,code = <KEY_HELP>;
};
wlan {
label = "wlan";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
linux,code = <KEY_WLAN>;
};
restart {
label = "restart";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
linux,code = <KEY_RESTART>;
};
reset {
label = "reset";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
linux,code = <KEY_CONFIG>;
};
};
message_red {
label = "HW556:red:message";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
};
hspa_red {
label = "HW556:red:hspa";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
dsl_red {
label = "HW556:red:dsl";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
power_red {
label = "HW556:red:power";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
default-state = "on";
};
all_red {
label = "HW556:red:all";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
default-state = "on";
};
lan1_green {
label = "HW556:green:lan1";
- gpios = <&gpio0 12 1>;
+ gpios = <&pinctrl 12 1>;
};
lan1_red {
label = "HW556:red:lan1";
- gpios = <&gpio0 13 1>;
+ gpios = <&pinctrl 13 1>;
};
lan2_green {
label = "HW556:green:lan2";
- gpios = <&gpio0 15 1>;
+ gpios = <&pinctrl 15 1>;
};
lan2_red {
label = "HW556:red:lan2";
- gpios = <&gpio0 22 1>;
+ gpios = <&pinctrl 22 1>;
};
lan3_green {
label = "HW556:green:lan3";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
};
lan3_red {
label = "HW556:red:lan3";
- gpios = <&gpio0 26 1>;
+ gpios = <&pinctrl 26 1>;
};
lan4_green {
label = "HW556:green:lan4";
- gpios = <&gpio0 27 1>;
+ gpios = <&pinctrl 27 1>;
};
lan4_red {
label = "HW556:red:lan4";
- gpios = <&gpio0 28 1>;
+ gpios = <&pinctrl 28 1>;
};
};
};
help {
label = "help";
- gpios = <&gpio0 8 1>;
+ gpios = <&pinctrl 8 1>;
linux,code = <KEY_HELP>;
};
wlan {
label = "wlan";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
linux,code = <KEY_WLAN>;
};
restart {
label = "restart";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
linux,code = <KEY_RESTART>;
};
reset {
label = "reset";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
linux,code = <KEY_CONFIG>;
};
};
message_red {
label = "HW556:red:message";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
};
hspa_red {
label = "HW556:red:hspa";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
dsl_red {
label = "HW556:red:dsl";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
power_red {
label = "HW556:red:power";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
default-state = "on";
};
all_red {
label = "HW556:red:all";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
default-state = "on";
};
lan1_green {
label = "HW556:green:lan1";
- gpios = <&gpio0 12 1>;
+ gpios = <&pinctrl 12 1>;
};
lan1_red {
label = "HW556:red:lan1";
- gpios = <&gpio0 13 1>;
+ gpios = <&pinctrl 13 1>;
};
lan2_green {
label = "HW556:green:lan2";
- gpios = <&gpio0 15 1>;
+ gpios = <&pinctrl 15 1>;
};
lan2_red {
label = "HW556:red:lan2";
- gpios = <&gpio0 22 1>;
+ gpios = <&pinctrl 22 1>;
};
lan3_green {
label = "HW556:green:lan3";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
};
lan3_red {
label = "HW556:red:lan3";
- gpios = <&gpio0 26 1>;
+ gpios = <&pinctrl 26 1>;
};
lan4_green {
label = "HW556:green:lan4";
- gpios = <&gpio0 27 1>;
+ gpios = <&pinctrl 27 1>;
};
lan4_red {
label = "HW556:red:lan4";
- gpios = <&gpio0 28 1>;
+ gpios = <&pinctrl 28 1>;
};
};
};
help {
label = "help";
- gpios = <&gpio1 4 1>;
+ gpios = <&pinctrl 36 1>;
linux,code = <KEY_HELP>;
};
wlan {
label = "wlan";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
linux,code = <KEY_WLAN>;
};
restart {
label = "restart";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
linux,code = <KEY_RESTART>;
};
reset {
label = "reset";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
linux,code = <KEY_CONFIG>;
};
};
lan1_green {
label = "HW556:green:lan1";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
};
lan2_green {
label = "HW556:green:lan2";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
dsl_red {
label = "HW556:red:dsl";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
power_red {
label = "HW556:red:power";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
default-state = "on";
};
message_red {
label = "HW556:red:message";
- gpios = <&gpio0 12 1>;
+ gpios = <&pinctrl 12 1>;
};
lan1_red {
label = "HW556:red:lan1";
- gpios = <&gpio0 13 1>;
+ gpios = <&pinctrl 13 1>;
};
hspa_red {
label = "HW556:red:hspa";
- gpios = <&gpio0 15 1>;
+ gpios = <&pinctrl 15 1>;
};
lan2_red {
label = "HW556:red:lan2";
- gpios = <&gpio0 22 1>;
+ gpios = <&pinctrl 22 1>;
};
lan3_green {
label = "HW556:green:lan3";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
};
lan3_red {
label = "HW556:red:lan3";
- gpios = <&gpio0 26 1>;
+ gpios = <&pinctrl 26 1>;
};
lan4_green {
label = "HW556:green:lan4";
- gpios = <&gpio0 27 1>;
+ gpios = <&pinctrl 27 1>;
};
lan4_red {
label = "HW556:red:lan4";
- gpios = <&gpio0 28 1>;
+ gpios = <&pinctrl 28 1>;
};
};
};
reset {
label = "reset";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_RESTART>;
};
};
dsl_green {
label = "HG622:green:dsl";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
inet_green {
label = "HG622:green:inet";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
usb_green {
label = "HG622:green:usb";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
power_green {
label = "HG622:green:power";
- gpios = <&gpio0 22 1>;
+ gpios = <&pinctrl 22 1>;
default-state = "on";
};
};
reg = <0xfe0000 0x020000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci_gnt0 &pinctrl_pci_req0
+ &pinctrl_pci_intb &pinctrl_pci_gnt1
+ &pinctrl_pci_req1>;
+};
wps {
label = "wps";
- gpios = <&gpio0 12 1>;
+ gpios = <&pinctrl 12 1>;
linux,code = <KEY_WPS_BUTTON>;
};
wlan {
label = "wlan";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
linux,code = <KEY_WLAN>;
};
reset {
label = "reset";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_RESTART>;
};
};
dsl_green {
label = "HW65x:green:dsl";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
internet_green {
label = "HW65x:green:internet";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
+
usb_green {
label = "HW65x:green:usb";
- gpios = <&gpio0 14 1>;
+ gpios = <&pinctrl 14 1>;
};
power_green {
label = "HW65x:green:power";
- gpios = <&gpio0 22 1>;
+ gpios = <&pinctrl 22 1>;
default-state = "on";
};
voip_green {
label = "HW65x:green:voip";
- gpios = <&gpio0 25 1>;
+ gpios = <&pinctrl 25 1>;
};
wps_green {
label = "HW65x:green:wps";
- gpios = <&gpio0 27 1>;
+ gpios = <&pinctrl 27 1>;
};
};
};
reg = <0x7e0000 0x020000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ephy0_led &pinctrl_ephy1_led
+ &pinctrl_ephy2_led &pinctrl_ephy3_led>;
+};
#size-cells = <0>;
compatible = "spi-gpio";
- gpio-mosi = <&gpio0 7 0>;
- gpio-sck = <&gpio0 6 0>;
- cs-gpios = <&gpio0 5 0>;
+ gpio-mosi = <&pinctrl 7 0>;
+ gpio-sck = <&pinctrl 6 0>;
+ cs-gpios = <&pinctrl 5 0>;
num-chipselects = <1>;
hc595: gpio-spi-controller@0 {
phone {
label = "phone";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
linux,code = <KEY_PHONE>;
};
reset {
label = "reset";
- gpios = <&gpio0 9 1>;
+ gpios = <&pinctrl 9 1>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
linux,code = <KEY_WPS_BUTTON>;
};
};
button1 {
label = "1";
- gpios = <&gpio1 4 1>;
+ gpios = <&pinctrl 36 1>;
linux,code = <KEY_RESTART>;
};
button2 {
label = "2";
- gpios = <&gpio0 7 1>;
+ gpios = <&pinctrl 7 1>;
linux,code = <BTN_2>;
};
};
red_adsl_fail {
label = "Livebox1:red:adsl-fail-power";
- gpios = <&gpio0 0 0>;
+ gpios = <&pinctrl 0 0>;
default-state = "on";
};
red_adsl {
label = "Livebox1:red:adsl";
- gpios = <&gpio0 1 0>;
+ gpios = <&pinctrl 1 0>;
};
red_traffic {
label = "Livebox1:red:traffic";
- gpios = <&gpio0 2 0>;
+ gpios = <&pinctrl 2 0>;
};
red_phone {
label = "Livebox1:red:phone";
- gpios = <&gpio0 3 0>;
+ gpios = <&pinctrl 3 0>;
};
red_wifi {
label = "Livebox1:red:wifi";
- gpios = <&gpio0 4 0>;
+ gpios = <&pinctrl 4 0>;
};
};
};
linux,part-probe = "RedBoot";
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii &pinctrl_mii_pccard>;
+};
power {
label = "MAGIC:green:power";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
default-state = "on";
};
stop {
label = "MAGIC:green:stop";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
hpna {
label = "MAGIC:green:hpna";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
status {
label = "MAGIC:green:adsl";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
voip {
label = "MAGIC:green:voip";
- gpios = <&gpio0 22 1>;
+ gpios = <&pinctrl 22 1>;
};
wifi {
label = "MAGIC:green:wifi";
- gpios = <&gpio0 28 0>;
+ gpios = <&pinctrl 28 0>;
};
usb {
label = "MAGIC:green:usb";
- gpios = <&gpio1 3 1>;
+ gpios = <&pinctrl 35 1>;
};
};
};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii &pinctrl_mii_pccard>;
+};
#size-cells = <0>;
compatible = "spi-gpio";
- gpio-mosi = <&gpio0 7 0>;
- gpio-sck = <&gpio0 6 0>;
+ gpio-mosi = <&pinctrl 7 0>;
+ gpio-sck = <&pinctrl 6 0>;
num-chipselects = <0>;
hc595: gpio-spi-controller@0 {
service {
label = "service";
- gpios = <&gpio0 27 1>;
+ gpios = <&pinctrl 27 1>;
linux,code = <BTN_0>;
};
clip {
label = "clip";
- gpios = <&gpio0 31 1>;
+ gpios = <&pinctrl 31 1>;
linux,code = <BTN_1>;
};
reset {
label = "reset";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
- gpios = <&gpio1 5 1>;
+ gpios = <&pinctrl 37 1>;
linux,code = <KEY_WPS_BUTTON>;
};
};
traffic_white {
label = "NB4-FXC-r1:white:traffic";
- gpios = <&gpio0 2 0>;
+ gpios = <&pinctrl 2 0>;
};
service_blue {
label = "NB4-FXC-r1:blue:service";
- gpios = <&gpio0 4 0>;
+ gpios = <&pinctrl 4 0>;
};
wifi_white {
label = "NB4-FXC-r1:white:wifi";
- gpios = <&gpio0 15 0>;
+ gpios = <&pinctrl 15 0>;
};
service_red {
label = "NB4-FXC-r1:red:service";
- gpios = <&gpio0 29 0>;
+ gpios = <&pinctrl 29 0>;
};
service_green {
label = "NB4-FXC-r1:green:service";
- gpios = <&gpio0 30 0>;
+ gpios = <&pinctrl 30 0>;
};
alarm_white {
label = "NB4-FXC-r1:white:alarm";
#size-cells = <0>;
compatible = "spi-gpio";
- gpio-mosi = <&gpio0 7 0>;
- gpio-sck = <&gpio0 6 0>;
+ gpio-mosi = <&pinctrl 7 0>;
+ gpio-sck = <&pinctrl 6 0>;
num-chipselects = <0>;
hc595: gpio-spi-controller@0 {
service {
label = "service";
- gpios = <&gpio0 27 1>;
+ gpios = <&pinctrl 27 1>;
linux,code = <BTN_0>;
};
clip {
label = "clip";
- gpios = <&gpio0 31 1>;
+ gpios = <&pinctrl 31 1>;
linux,code = <BTN_1>;
};
reset {
label = "reset";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
- gpios = <&gpio1 5 1>;
+ gpios = <&pinctrl 37 1>;
linux,code = <KEY_WPS_BUTTON>;
};
};
traffic_white {
label = "NB4-SER-r0:white:traffic";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
service_blue {
label = "NB4-SER-r0:blue:service";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
wifi_white {
label = "NB4-SER-r0:white:wifi";
- gpios = <&gpio0 15 1>;
+ gpios = <&pinctrl 15 1>;
};
service_red {
label = "NB4-SER-r0:red:service";
- gpios = <&gpio0 29 1>;
+ gpios = <&pinctrl 29 1>;
};
service_green {
label = "NB4-SER-r0:green:service";
- gpios = <&gpio0 30 1>;
+ gpios = <&pinctrl 30 1>;
};
alarm_white {
label = "NB4-SER-r0:white:alarm";
service {
label = "service";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
linux,code = <BTN_0>;
};
wlan {
label = "wlan";
- gpios = <&gpio0 12 1>;
+ gpios = <&pinctrl 12 1>;
linux,code = <KEY_WLAN>;
};
reset {
label = "reset";
- gpios = <&gpio0 24 1>;
+ gpios = <&pinctrl 24 1>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
- gpios = <&gpio0 25 1>;
+ gpios = <&pinctrl 25 1>;
linux,code = <KEY_WPS_BUTTON>;
};
};
switch {
compatible = "realtek,rtl8367";
- gpio-sda = <&gpio0 18 0>;
- gpio-sck = <&gpio0 20 0>;
+ gpio-sda = <&pinctrl 18 0>;
+ gpio-sck = <&pinctrl 20 0>;
realtek,extif0 = <1 5 1 1 1 1 1 1 2>;
};
reset {
label = "reset";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 35 1>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
- gpios = <&gpio1 3 1>;
+ gpios = <&pinctrl 36 1>;
linux,code = <KEY_WPS_BUTTON>;
};
};
power_green {
label = "P870HW-51a:green:power";
- gpios = <&gpio0 0 0>;
+ gpios = <&pinctrl 0 0>;
default-state = "on";
};
dsl_green {
label = "P870HW-51a:green:dsl";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
inet_green {
label = "P870HW-51a:green:inet";
- gpios = <&gpio0 22 1>;
+ gpios = <&pinctrl 22 1>;
};
wps_orange {
label = "P870HW-51a:orange:wps";
- gpios = <&gpio0 24 1>;
+ gpios = <&pinctrl 24 1>;
};
inet_red {
label = "P870HW-51a:red:inet";
- gpios = <&gpio1 1 1>;
+ gpios = <&pinctrl 33 1>;
};
};
};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci>;
+};
reset {
label = "reset";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
- gpios = <&gpio0 24 1>;
+ gpios = <&pinctrl 24 1>;
linux,code = <KEY_WPS_BUTTON>;
};
};
inet_green {
label = "R5010UNv2:green:inet";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
inet_fail_red {
label = "R5010UNv2:red:inet-fail";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
dsl_red {
label = "R5010UNv2:green:dsl";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
power_green {
label = "R5010UNv2:green:power";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
default-state = "on";
};
power_fail_red {
label = "R5010UNv2:red:power-fail";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
wps_green {
label = "R5010UNv2:green:wps";
- gpios = <&gpio0 10 1>;
+ gpios = <&pinctrl 10 1>;
};
usb_green {
label = "R5010UNv2:green:usb";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
};
};
stop_green {
label = "96358VW2:green:stop";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
power_green {
label = "96358VW2:green:power";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
default-state = "on";
};
adsl_green {
label = "96358VW2:green:adsl";
- gpios = <&gpio0 22 1>;
+ gpios = <&pinctrl 22 1>;
};
ppp_fail_green {
label = "96358VW2:green:ppp-fail";
- gpios = <&gpio0 23 0>;
+ gpios = <&pinctrl 23 0>;
};
};
};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii>;
+};
reset {
label = "reset";
- gpios = <&gpio0 11 0>;
+ gpios = <&pinctrl 11 0>;
linux,code = <KEY_RESTART>;
};
ses {
label = "ses";
- gpios = <&gpio1 5 1>;
+ gpios = <&pinctrl 37 1>;
linux,code = <KEY_WPS_BUTTON>;
};
};
ses_green {
label = "spw303v:green:ses";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
};
power_adsl_red {
label = "spw303v:red:power+adsl";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
ppp_green {
label = "spw303v:green:ppp";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
power_adsl_green {
label = "spw303v:green:power+adsl";
- gpios = <&gpio0 22 1>;
+ gpios = <&pinctrl 22 1>;
default-state = "on";
};
voip_green {
label = "spw303v:green:voip";
- gpios = <&gpio0 27 1>;
+ gpios = <&pinctrl 27 1>;
};
pots_green {
label = "spw303v:green:pots";
- gpios = <&gpio0 31 1>;
+ gpios = <&pinctrl 31 1>;
};
};
};
reset {
label = "reset";
- gpios = <&gpio1 1 1>;
+ gpios = <&pinctrl 33 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "SPW500V:green:power";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
default-state = "on";
};
power_red {
label = "SPW500V:red:power";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
ppp_green {
label = "SPW500V:green:ppp";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
pstn_green {
label = "SPW500V:green:pstn";
- gpios = <&gpio0 28 1>;
+ gpios = <&pinctrl 28 1>;
};
voip_green {
label = "SPW500V:green:voip";
- gpios = <&gpio1 0 1>;
+ gpios = <&pinctrl 32 1>;
};
};
};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci>;
+};
reset {
label = "reset";
- gpios = <&gpio1 1 1>;
+ gpios = <&pinctrl 33 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "96348GW-11:green:power";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
default-state = "on";
};
stop_green {
label = "96348GW-11:green:stop";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
adsl_fail_green {
label = "96348GW-11:green:adsl-fail";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
ppp_green {
label = "96348GW-11:green:ppp";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
ppp_fail_green {
label = "96348GW-11:green:ppp-fail";
- gpios = <&gpio0 4 1>;
+ gpios = <&pinctrl 4 1>;
};
};
};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii &pinctrl_mii_pccard>;
+};
usb {
label = "96348GW-A::usb";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
};
dsl {
label = "96348GW-A::adsl";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
};
};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii>;
+};
reset {
label = "reset";
- gpios = <&gpio1 1 1>;
+ gpios = <&pinctrl 33 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "V2110:green:power";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
};
power_red {
label = "V2110:red:power";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
adsl_green {
label = "V2110:green:adsl";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
ppp_green {
label = "V2110:green:ppp";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
wireless_green {
label = "V2110:green:wireless";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
};
};
};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii>;
+};
reset {
label = "reset";
- gpios = <&gpio0 31 1>;
+ gpios = <&pinctrl 31 1>;
linux,code = <KEY_RESTART>;
};
};
power_green {
label = "V2500V_BB:green:power";
- gpios = <&gpio0 0 1>;
+ gpios = <&pinctrl 0 1>;
};
power_red {
label = "V2500V_BB:red:power";
- gpios = <&gpio0 1 1>;
+ gpios = <&pinctrl 1 1>;
};
adsl_green {
label = "V2500V_BB:green:adsl";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
ppp_green {
label = "V2500V_BB:green:ppp";
- gpios = <&gpio0 3 1>;
+ gpios = <&pinctrl 3 1>;
};
wireless_green {
label = "V2500V_BB:green:wireless";
- gpios = <&gpio0 6 1>;
+ gpios = <&pinctrl 6 1>;
};
};
};
reg = <0x3f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii>;
+};
reset {
label = "reset";
- gpios = <&gpio1 0 0>;
+ gpios = <&pinctrl 32 0>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
- gpios = <&gpio1 2 0>;
+ gpios = <&pinctrl 34 0>;
linux,code = <KEY_WPS_BUTTON>;
};
};
reset {
label = "reset";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
- gpios = <&gpio1 3 1>;
+ gpios = <&pinctrl 35 1>;
linux,code = <KEY_WPS_BUTTON>;
};
};
dsl_blue {
label = "VH4032N:blue:dsl";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
dsl_red {
label = "VH4032N:red:dsl";
- gpios = <&gpio0 5 1>;
+ gpios = <&pinctrl 5 1>;
};
hspa_blue {
label = "VH4032N:blue:hspa";
- gpios = <&gpio0 11 1>;
+ gpios = <&pinctrl 11 1>;
};
hspa_red {
label = "VH4032N:red:hspa";
- gpios = <&gpio0 12 1>;
+ gpios = <&pinctrl 12 1>;
};
power_blue {
label = "VH4032N:blue:power";
- gpios = <&gpio0 22 0>;
+ gpios = <&pinctrl 22 0>;
};
power_red {
label = "VH4032N:red:power";
- gpios = <&gpio0 24 0>;
+ gpios = <&pinctrl 24 0>;
default-state = "on";
};
voice_blue {
label = "VH4032N:blue:voice";
- gpios = <&gpio0 25 1>;
+ gpios = <&pinctrl 25 1>;
};
voice_red {
label = "VH4032N:red:voice";
- gpios = <&gpio0 26 1>;
+ gpios = <&pinctrl 26 1>;
};
};
};
-&gpio0 {
+&pinctrl {
usb_hub_reset {
gpio-hog;
gpios = <27 0>;
reset {
label = "reset";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_RESTART>;
};
};
dsl_green {
label = "VR-3025u:green:dsl";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
inet_green {
label = "VR-3025u:green:inet";
- gpios = <&gpio0 5 0>;
+ gpios = <&pinctrl 5 0>;
};
power_green {
label = "VR-3025u:green:power";
- gpios = <&gpio0 22 0>;
+ gpios = <&pinctrl 22 0>;
default-state = "on";
};
power_red {
label = "VR-3025u:red:power";
- gpios = <&gpio0 24 0>;
+ gpios = <&pinctrl 24 0>;
};
inet_red {
label = "VR-3025u:red:inet";
- gpios = <&gpio0 31 0>;
+ gpios = <&pinctrl 31 0>;
};
};
};
reg = <0x1fe0000 0x020000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ephy0_led &pinctrl_ephy1_led
+ &pinctrl_ephy2_led &pinctrl_ephy3_led>;
+};
reset {
label = "reset";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_RESTART>;
};
};
dsl_green {
label = "VR-3025un:green:dsl";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
inet_green {
label = "VR-3025un:green:inet";
- gpios = <&gpio0 5 0>;
+ gpios = <&pinctrl 5 0>;
};
power_green {
label = "VR-3025un:green:power";
- gpios = <&gpio0 22 0>;
+ gpios = <&pinctrl 22 0>;
default-state = "on";
};
power_red {
label = "VR-3025un:red:power";
- gpios = <&gpio0 24 0>;
+ gpios = <&pinctrl 24 0>;
};
inet_red {
label = "VR-3025un:red:inet";
- gpios = <&gpio0 31 0>;
+ gpios = <&pinctrl 31 0>;
};
};
};
reg = <0x7f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ephy0_led &pinctrl_ephy1_led
+ &pinctrl_ephy2_led &pinctrl_ephy3_led>;
+};
reset {
label = "reset";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_RESTART>;
};
};
dsl_green {
label = "VR-3026e:green:dsl";
- gpios = <&gpio0 2 1>;
+ gpios = <&pinctrl 2 1>;
};
inet_green {
label = "VR-3026e:green:inet";
- gpios = <&gpio0 5 0>;
+ gpios = <&pinctrl 5 0>;
};
power_green {
label = "VR-3026e:green:power";
- gpios = <&gpio0 22 0>;
+ gpios = <&pinctrl 22 0>;
default-state = "on";
};
power_red {
label = "VR-3026e:red:power";
- gpios = <&gpio0 24 0>;
+ gpios = <&pinctrl 24 0>;
};
inet_red {
label = "VR-3026e:red:inet";
- gpios = <&gpio0 31 0>;
+ gpios = <&pinctrl 31 0>;
};
};
};
reg = <0x7f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci &pinctrl_ephy0_led &pinctrl_ephy1_led
+ &pinctrl_ephy2_led &pinctrl_ephy3_led>;
+};
wlan {
label = "wlan";
- gpios = <&gpio1 0 1>;
+ gpios = <&pinctrl 32 1>;
linux,code = <KEY_WLAN>;
};
reset {
label = "reset";
- gpios = <&gpio1 2 1>;
+ gpios = <&pinctrl 34 1>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
- gpios = <&gpio1 3 1>;
+ gpios = <&pinctrl 35 1>;
linux,code = <KEY_WPS_BUTTON>;
};
};
inet_green {
label = "WAP-5813n:green:inet";
- gpios = <&gpio0 5 0>;
+ gpios = <&pinctrl 5 0>;
};
power_green {
label = "WAP-5813n:green:power";
- gpios = <&gpio0 22 0>;
+ gpios = <&pinctrl 22 0>;
default-state = "on";
};
wps_green {
label = "WAP-5813n:green:wps";
- gpios = <&gpio0 23 1>;
+ gpios = <&pinctrl 23 1>;
};
power_red {
label = "WAP-5813n:red:power";
- gpios = <&gpio0 24 0>;
+ gpios = <&pinctrl 24 0>;
};
inet_red {
label = "WAP-5813n:red:inet";
- gpios = <&gpio0 31 0>;
+ gpios = <&pinctrl 31 0>;
};
};
};
reg = <0x7f0000 0x010000>;
};
};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pci>;
+};
--- /dev/null
+From 0cf3292cde22f8843ae5d1eeb8466d8121243c1a Mon Sep 17 00:00:00 2001
+From: Laxman Dewangan <ldewangan@nvidia.com>
+Date: Mon, 15 Feb 2016 16:32:09 +0530
+Subject: [PATCH] gpio: Add devm_ apis for gpiochip_add_data and
+ gpiochip_remove
+
+Add device managed APIs devm_gpiochip_add_data() and
+devm_gpiochip_remove() for the APIs gpiochip_add_data()
+and gpiochip_remove().
+
+This helps in reducing code in error path and sometimes
+removal of .remove callback for driver unbind.
+
+Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
+---
+ drivers/gpio/gpiolib.c | 74 +++++++++++++++++++++++++++++++++++++++++++++
+ include/linux/gpio/driver.h | 4 +++
+ 2 files changed, 78 insertions(+)
+
+--- a/drivers/gpio/gpiolib.c
++++ b/drivers/gpio/gpiolib.c
+@@ -433,6 +433,80 @@ void gpiochip_remove(struct gpio_chip *c
+ }
+ EXPORT_SYMBOL_GPL(gpiochip_remove);
+
++static void devm_gpio_chip_release(struct device *dev, void *res)
++{
++ struct gpio_chip *chip = *(struct gpio_chip **)res;
++
++ gpiochip_remove(chip);
++}
++
++static int devm_gpio_chip_match(struct device *dev, void *res, void *data)
++
++{
++ struct gpio_chip **r = res;
++
++ if (!r || !*r) {
++ WARN_ON(!r || !*r);
++ return 0;
++ }
++
++ return *r == data;
++}
++
++/**
++ * devm_gpiochip_add_data() - Resource manager piochip_add_data()
++ * @dev: the device pointer on which irq_chip belongs to.
++ * @chip: the chip to register, with chip->base initialized
++ * Context: potentially before irqs will work
++ *
++ * Returns a negative errno if the chip can't be registered, such as
++ * because the chip->base is invalid or already associated with a
++ * different chip. Otherwise it returns zero as a success code.
++ *
++ * The gpio chip automatically be released when the device is unbound.
++ */
++int devm_gpiochip_add_data(struct device *dev, struct gpio_chip *chip,
++ void *data)
++{
++ struct gpio_chip **ptr;
++ int ret;
++
++ ptr = devres_alloc(devm_gpio_chip_release, sizeof(*ptr),
++ GFP_KERNEL);
++ if (!ptr)
++ return -ENOMEM;
++
++ ret = gpiochip_add_data(chip, data);
++ if (ret < 0) {
++ devres_free(ptr);
++ return ret;
++ }
++
++ *ptr = chip;
++ devres_add(dev, ptr);
++
++ return 0;
++}
++EXPORT_SYMBOL_GPL(devm_gpiochip_add_data);
++
++/**
++ * devm_gpiochip_remove() - Resource manager of gpiochip_remove()
++ * @dev: device for which which resource was allocated
++ * @chip: the chip to remove
++ *
++ * A gpio_chip with any GPIOs still requested may not be removed.
++ */
++void devm_gpiochip_remove(struct device *dev, struct gpio_chip *chip)
++{
++ int ret;
++
++ ret = devres_release(dev, devm_gpio_chip_release,
++ devm_gpio_chip_match, chip);
++ if (!ret)
++ WARN_ON(ret);
++}
++EXPORT_SYMBOL_GPL(devm_gpiochip_remove);
++
+ /**
+ * gpiochip_find() - iterator for locating a specific gpio_chip
+ * @data: data to pass to match function
+--- a/include/linux/gpio/driver.h
++++ b/include/linux/gpio/driver.h
+@@ -206,6 +206,10 @@ static inline int gpiochip_add(struct gp
+ return gpiochip_add_data(chip, NULL);
+ }
+ extern void gpiochip_remove(struct gpio_chip *chip);
++extern int devm_gpiochip_add_data(struct device *dev, struct gpio_chip *chip,
++ void *data);
++extern void devm_gpiochip_remove(struct device *dev, struct gpio_chip *chip);
++
+ extern struct gpio_chip *gpiochip_find(void *data,
+ int (*match)(struct gpio_chip *chip, void *data));
+
--- /dev/null
+From 80e0f8d94d3090f0f7bf3faf3e6180e920ee0d22 Mon Sep 17 00:00:00 2001
+From: Laxman Dewangan <ldewangan@nvidia.com>
+Date: Wed, 24 Feb 2016 14:12:59 +0530
+Subject: [PATCH] pinctrl: Add devm_ apis for pinctrl_{register, unregister}
+
+Add device managed APIs devm_pinctrl_register() and
+devm_pinctrl_unregister() for the APIs pinctrl_register()
+and pinctrl_unregister().
+
+This helps in reducing code in error path and sometimes
+removal of .remove callback for driver unbind.
+
+Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
+Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
+Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
+Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
+---
+ drivers/pinctrl/core.c | 63 +++++++++++++++++++++++++++++++++++++++++
+ include/linux/pinctrl/pinctrl.h | 6 ++++
+ 2 files changed, 69 insertions(+)
+
+--- a/drivers/pinctrl/core.c
++++ b/drivers/pinctrl/core.c
+@@ -1861,6 +1861,69 @@ void pinctrl_unregister(struct pinctrl_d
+ }
+ EXPORT_SYMBOL_GPL(pinctrl_unregister);
+
++static void devm_pinctrl_dev_release(struct device *dev, void *res)
++{
++ struct pinctrl_dev *pctldev = *(struct pinctrl_dev **)res;
++
++ pinctrl_unregister(pctldev);
++}
++
++static int devm_pinctrl_dev_match(struct device *dev, void *res, void *data)
++{
++ struct pctldev **r = res;
++
++ if (WARN_ON(!r || !*r))
++ return 0;
++
++ return *r == data;
++}
++
++/**
++ * devm_pinctrl_register() - Resource managed version of pinctrl_register().
++ * @dev: parent device for this pin controller
++ * @pctldesc: descriptor for this pin controller
++ * @driver_data: private pin controller data for this pin controller
++ *
++ * Returns an error pointer if pincontrol register failed. Otherwise
++ * it returns valid pinctrl handle.
++ *
++ * The pinctrl device will be automatically released when the device is unbound.
++ */
++struct pinctrl_dev *devm_pinctrl_register(struct device *dev,
++ struct pinctrl_desc *pctldesc,
++ void *driver_data)
++{
++ struct pinctrl_dev **ptr, *pctldev;
++
++ ptr = devres_alloc(devm_pinctrl_dev_release, sizeof(*ptr), GFP_KERNEL);
++ if (!ptr)
++ return ERR_PTR(-ENOMEM);
++
++ pctldev = pinctrl_register(pctldesc, dev, driver_data);
++ if (IS_ERR(pctldev)) {
++ devres_free(ptr);
++ return pctldev;
++ }
++
++ *ptr = pctldev;
++ devres_add(dev, ptr);
++
++ return pctldev;
++}
++EXPORT_SYMBOL_GPL(devm_pinctrl_register);
++
++/**
++ * devm_pinctrl_unregister() - Resource managed version of pinctrl_unregister().
++ * @dev: device for which which resource was allocated
++ * @pctldev: the pinctrl device to unregister.
++ */
++void devm_pinctrl_unregister(struct device *dev, struct pinctrl_dev *pctldev)
++{
++ WARN_ON(devres_release(dev, devm_pinctrl_dev_release,
++ devm_pinctrl_dev_match, pctldev));
++}
++EXPORT_SYMBOL_GPL(devm_pinctrl_unregister);
++
+ static int __init pinctrl_init(void)
+ {
+ pr_info("initialized pinctrl subsystem\n");
+--- a/include/linux/pinctrl/pinctrl.h
++++ b/include/linux/pinctrl/pinctrl.h
+@@ -144,6 +144,12 @@ struct pinctrl_desc {
+ extern struct pinctrl_dev *pinctrl_register(struct pinctrl_desc *pctldesc,
+ struct device *dev, void *driver_data);
+ extern void pinctrl_unregister(struct pinctrl_dev *pctldev);
++extern struct pinctrl_dev *devm_pinctrl_register(struct device *dev,
++ struct pinctrl_desc *pctldesc,
++ void *driver_data);
++extern void devm_pinctrl_unregister(struct device *dev,
++ struct pinctrl_dev *pctldev);
++
+ extern bool pin_is_valid(struct pinctrl_dev *pctldev, int pin);
+ extern void pinctrl_add_gpio_range(struct pinctrl_dev *pctldev,
+ struct pinctrl_gpio_range *range);
--- /dev/null
+From d32f7fd3bbc32732b094d938b95169521503a9fb Mon Sep 17 00:00:00 2001
+From: Irina Tirdea <irina.tirdea@intel.com>
+Date: Thu, 31 Mar 2016 14:44:42 +0300
+Subject: [PATCH] pinctrl: Rename pinctrl_utils_dt_free_map to
+ pinctrl_utils_free_map
+
+Rename pinctrl_utils_dt_free_map to pinctrl_utils_free_map, since
+it does not depend on device tree despite the current name. This
+will enforce a consistent naming in pinctr-utils.c and will make
+it clear it can be called from outside device tree (e.g. from
+ACPI handling code).
+
+Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
+Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
+---
+ drivers/pinctrl/pinconf-generic.c | 2 +-
+ drivers/pinctrl/pinctrl-utils.c | 4 ++--
+ drivers/pinctrl/pinctrl-utils.h | 2 +-
+ 3 files changed, 4 insertions(+), 4 deletions(-)
+
+--- a/drivers/pinctrl/pinconf-generic.c
++++ b/drivers/pinctrl/pinconf-generic.c
+@@ -385,7 +385,7 @@ int pinconf_generic_dt_node_to_map(struc
+ return 0;
+
+ exit:
+- pinctrl_utils_dt_free_map(pctldev, *map, *num_maps);
++ pinctrl_utils_free_map(pctldev, *map, *num_maps);
+ return ret;
+ }
+ EXPORT_SYMBOL_GPL(pinconf_generic_dt_node_to_map);
+--- a/drivers/pinctrl/pinctrl-utils.c
++++ b/drivers/pinctrl/pinctrl-utils.c
+@@ -122,7 +122,7 @@ int pinctrl_utils_add_config(struct pinc
+ }
+ EXPORT_SYMBOL_GPL(pinctrl_utils_add_config);
+
+-void pinctrl_utils_dt_free_map(struct pinctrl_dev *pctldev,
++void pinctrl_utils_free_map(struct pinctrl_dev *pctldev,
+ struct pinctrl_map *map, unsigned num_maps)
+ {
+ int i;
+@@ -139,4 +139,4 @@ void pinctrl_utils_dt_free_map(struct pi
+ }
+ kfree(map);
+ }
+-EXPORT_SYMBOL_GPL(pinctrl_utils_dt_free_map);
++EXPORT_SYMBOL_GPL(pinctrl_utils_free_map);
+--- a/drivers/pinctrl/pinctrl-utils.h
++++ b/drivers/pinctrl/pinctrl-utils.h
+@@ -37,7 +37,7 @@ int pinctrl_utils_add_map_configs(struct
+ int pinctrl_utils_add_config(struct pinctrl_dev *pctldev,
+ unsigned long **configs, unsigned *num_configs,
+ unsigned long config);
+-void pinctrl_utils_dt_free_map(struct pinctrl_dev *pctldev,
++void pinctrl_utils_free_map(struct pinctrl_dev *pctldev,
+ struct pinctrl_map *map, unsigned num_maps);
+
+ #endif /* __PINCTRL_UTILS_H__ */
--- /dev/null
+From ab2f33e35e35905a76204138143875251f3e1088 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Fri, 24 Jun 2016 22:07:42 +0200
+Subject: [PATCH 01/13] pinctrl: add bcm63xx base code
+
+Setup directory and add a helper for bcm63xx pinctrl support.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ drivers/pinctrl/Kconfig | 1 +
+ drivers/pinctrl/Makefile | 1 +
+ drivers/pinctrl/bcm63xx/Kconfig | 3 +
+ drivers/pinctrl/bcm63xx/Makefile | 1 +
+ drivers/pinctrl/bcm63xx/pinctrl-bcm63xx.c | 142 ++++++++++++++++++++++++++++++
+ drivers/pinctrl/bcm63xx/pinctrl-bcm63xx.h | 14 +++
+ 7 files changed, 163 insertions(+)
+ create mode 100644 drivers/pinctrl/bcm63xx/Kconfig
+ create mode 100644 drivers/pinctrl/bcm63xx/Makefile
+ create mode 100644 drivers/pinctrl/bcm63xx/pinctrl-bcm63xx.c
+ create mode 100644 drivers/pinctrl/bcm63xx/pinctrl-bcm63xx.h
+
+--- a/drivers/pinctrl/Kconfig
++++ b/drivers/pinctrl/Kconfig
+@@ -247,6 +247,7 @@ config PINCTRL_ZYNQ
+ This selectes the pinctrl driver for Xilinx Zynq.
+
+ source "drivers/pinctrl/bcm/Kconfig"
++source "drivers/pinctrl/bcm63xx/Kconfig"
+ source "drivers/pinctrl/berlin/Kconfig"
+ source "drivers/pinctrl/freescale/Kconfig"
+ source "drivers/pinctrl/intel/Kconfig"
+--- a/drivers/pinctrl/Makefile
++++ b/drivers/pinctrl/Makefile
+@@ -41,6 +41,7 @@ obj-$(CONFIG_PINCTRL_ST) += pinctrl-st.
+ obj-$(CONFIG_PINCTRL_ZYNQ) += pinctrl-zynq.o
+
+ obj-$(CONFIG_ARCH_BCM) += bcm/
++obj-y += bcm63xx/
+ obj-$(CONFIG_ARCH_BERLIN) += berlin/
+ obj-y += freescale/
+ obj-$(CONFIG_X86) += intel/
+--- /dev/null
++++ b/drivers/pinctrl/bcm63xx/Kconfig
+@@ -0,0 +1,3 @@
++config PINCTRL_BCM63XX
++ bool
++ select GPIO_GENERIC
+--- /dev/null
++++ b/drivers/pinctrl/bcm63xx/Makefile
+@@ -0,0 +1 @@
++obj-$(CONFIG_PINCTRL_BCM63XX) += pinctrl-bcm63xx.o
+--- /dev/null
++++ b/drivers/pinctrl/bcm63xx/pinctrl-bcm63xx.c
+@@ -0,0 +1,155 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License. See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2016 Jonas Gorski <jonas.gorski@gmail.com>
++ */
++
++#include <linux/bitops.h>
++#include <linux/device.h>
++#include <linux/gpio/driver.h>
++#include <linux/of_irq.h>
++
++#include "pinctrl-bcm63xx.h"
++#include "../core.h"
++
++#define BANK_SIZE sizeof(u32)
++#define PINS_PER_BANK (BANK_SIZE * BITS_PER_BYTE)
++
++#ifdef CONFIG_OF
++static int bcm63xx_gpio_of_xlate(struct gpio_chip *gc,
++ const struct of_phandle_args *gpiospec,
++ u32 *flags)
++{
++ struct gpio_chip *base = gpiochip_get_data(gc);
++ int pin = gpiospec->args[0];
++
++ if (gc != &base[pin / PINS_PER_BANK])
++ return -EINVAL;
++
++ pin = pin % PINS_PER_BANK;
++
++ if (pin >= gc->ngpio)
++ return -EINVAL;
++
++ if (flags)
++ *flags = gpiospec->args[1];
++
++ return pin;
++}
++#endif
++
++static int bcm63xx_gpio_to_irq(struct gpio_chip *chip, unsigned gpio)
++{
++ struct gpio_chip *base = gpiochip_get_data(chip);
++ char irq_name[7]; /* "gpioXX" */
++
++ /* FIXME: this is ugly */
++ sprintf(irq_name, "gpio%d", gpio + PINS_PER_BANK * (chip - base));
++ return of_irq_get_byname(chip->of_node, irq_name);
++}
++
++static int bcm63xx_setup_gpio(struct device *dev, struct gpio_chip *gc,
++ void __iomem *dirout, void __iomem *data,
++ size_t sz, int ngpio)
++
++{
++ int banks, chips, i, ret = -EINVAL;
++
++ chips = DIV_ROUND_UP(ngpio, PINS_PER_BANK);
++ banks = sz / BANK_SIZE;
++
++ for (i = 0; i < chips; i++) {
++ int offset, pins;
++ int reg_offset;
++ char *label;
++
++ label = devm_kasprintf(dev, GFP_KERNEL, "bcm63xx-gpio.%i", i);
++ if (!label)
++ return -ENOMEM;
++
++ offset = i * PINS_PER_BANK;
++ pins = min_t(int, ngpio - offset, PINS_PER_BANK);
++
++ /* the registers are treated like a huge big endian register */
++ reg_offset = (banks - i - 1) * BANK_SIZE;
++
++ ret = bgpio_init(&gc[i], dev, BANK_SIZE, data + reg_offset,
++ NULL, NULL, dirout + reg_offset, NULL,
++ BGPIOF_BIG_ENDIAN_BYTE_ORDER);
++ if (ret)
++ return ret;
++
++ gc[i].request = gpiochip_generic_request;
++ gc[i].free = gpiochip_generic_free;
++
++ if (of_get_property(dev->of_node, "interrupt-names", NULL))
++ gc[i].to_irq = bcm63xx_gpio_to_irq;
++
++#ifdef CONFIG_OF
++ gc[i].of_gpio_n_cells = 2;
++ gc[i].of_xlate = bcm63xx_gpio_of_xlate;
++#endif
++
++ gc[i].label = label;
++ gc[i].ngpio = pins;
++
++ devm_gpiochip_add_data(dev, &gc[i], gc);
++ }
++
++ return 0;
++}
++
++static void bcm63xx_setup_pinranges(struct gpio_chip *gc, const char *name,
++ int ngpio)
++{
++ int i, chips = DIV_ROUND_UP(ngpio, PINS_PER_BANK);
++
++ for (i = 0; i < chips; i++) {
++ int offset, pins;
++
++ offset = i * PINS_PER_BANK;
++ pins = min_t(int, ngpio - offset, PINS_PER_BANK);
++
++ gpiochip_add_pin_range(&gc[i], name, 0, offset, pins);
++ }
++}
++
++struct pinctrl_dev *bcm63xx_pinctrl_register(struct platform_device *pdev,
++ struct pinctrl_desc *desc,
++ void *priv, struct gpio_chip *gc,
++ int ngpio)
++{
++ struct pinctrl_dev *pctldev;
++ struct resource *res;
++ void __iomem *dirout, *data;
++ size_t sz;
++ int ret;
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dirout");
++ dirout = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(dirout))
++ return ERR_CAST(dirout);
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "dat");
++ data = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(data))
++ return ERR_CAST(data);
++
++ sz = resource_size(res);
++
++ ret = bcm63xx_setup_gpio(&pdev->dev, gc, dirout, data, sz, ngpio);
++ if (ret)
++ return ERR_PTR(ret);
++
++ pctldev = devm_pinctrl_register(&pdev->dev, desc, priv);
++ if (IS_ERR(pctldev))
++ return pctldev;
++
++ bcm63xx_setup_pinranges(gc, pinctrl_dev_get_devname(pctldev), ngpio);
++
++ dev_info(&pdev->dev, "registered at mmio %p\n", dirout);
++
++ return pctldev;
++}
+--- /dev/null
++++ b/drivers/pinctrl/bcm63xx/pinctrl-bcm63xx.h
+@@ -0,0 +1,14 @@
++#ifndef __PINCTRL_BCM63XX
++#define __PINCTRL_BCM63XX
++
++#include <linux/kernel.h>
++#include <linux/gpio.h>
++#include <linux/pinctrl/pinctrl.h>
++#include <linux/platform_device.h>
++
++struct pinctrl_dev *bcm63xx_pinctrl_register(struct platform_device *pdev,
++ struct pinctrl_desc *desc,
++ void *priv, struct gpio_chip *gc,
++ int ngpio);
++
++#endif
--- /dev/null
+From 4bdd40849632608d5cb7d3a64380cd76e7eea07b Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Wed, 27 Jul 2016 11:33:56 +0200
+Subject: [PATCH 02/16] Documentation: add BCM6328 pincontroller binding
+ documentation
+
+Add binding documentation for the pincontrol core found in BCM6328 SoCs.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ .../bindings/pinctrl/brcm,bcm6328-pinctrl.txt | 61 ++++++++++++++++++++++
+ 1 file changed, 61 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/pinctrl/brcm,bcm6328-pinctrl.txt
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6328-pinctrl.txt
+@@ -0,0 +1,61 @@
++* Broadcom BCM6328 pin controller
++
++Required properties:
++- compatible: Must be "brcm,bcm6328-pinctrl".
++- reg: Register specifies of dirout, dat, mode, mux registers.
++- reg-names: Must be "dirout", "dat", "mode", "mux".
++- gpio-controller: Identifies this node as a GPIO controller.
++- #gpio-cells: Must be <2>
++
++Example:
++
++pinctrl: pin-controller@10000080 {
++ compatible = "brcm,bcm6328-pinctrl";
++ reg = <0x10000080 0x8>,
++ <0x10000088 0x8>,
++ <0x10000098 0x4>,
++ <0x1000009c 0xc>;
++ reg-names = "dirout", "dat", "mode", "mux";
++
++ gpio-controller;
++ #gpio-cells = <2>;
++};
++
++Available pins/groups and functions:
++
++name pins functions
++-----------------------------------------------------------
++gpio0 0 led
++gpio1 1 led
++gpio2 2 led
++gpio3 3 led
++gpio4 4 led
++gpio5 5 led
++gpio6 6 led, serial_led_data
++gpio7 7 led, serial_led_clk
++gpio8 8 led
++gpio9 9 led
++gpio10 10 led
++gpio11 11 led
++gpio12 12 led
++gpio13 13 led
++gpio14 14 led
++gpio15 15 led
++gpio16 16 led, pcie_clkreq
++gpio17 17 led
++gpio18 18 led
++gpio19 19 led
++gpio20 20 led
++gpio21 21 led
++gpio22 22 led
++gpio23 23 led
++gpio24 24 -
++gpio25 25 ephy0_act_led
++gpio26 26 ephy1_act_led
++gpio27 27 ephy2_act_led
++gpio28 28 ephy3_act_led
++gpio29 29 -
++gpio30 30 -
++gpio31 31 -
++hsspi_cs1 - hsspi_cs1
++usb_port1 - usb_host_port, usb_device_port
--- /dev/null
+From 393e9753f6492c1fdf55891ddee60d955ae8b119 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Fri, 24 Jun 2016 22:12:50 +0200
+Subject: [PATCH 03/16] pinctrl: add a pincontrol driver for BCM6328
+
+Add a pincontrol driver for BCM6328. BCM628 supports muxing 32 pins as
+GPIOs, as LEDs for the integrated LED controller, or various other
+functions. Its pincontrol mux registers also control other aspects, like
+switching the second USB port between host and device mode.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ drivers/pinctrl/bcm63xx/Kconfig | 7 +
+ drivers/pinctrl/bcm63xx/Makefile | 1 +
+ drivers/pinctrl/bcm63xx/pinctrl-bcm6328.c | 456 ++++++++++++++++++++++++++++++
+ 3 files changed, 464 insertions(+)
+ create mode 100644 drivers/pinctrl/bcm63xx/pinctrl-bcm6328.c
+
+--- a/drivers/pinctrl/bcm63xx/Kconfig
++++ b/drivers/pinctrl/bcm63xx/Kconfig
+@@ -1,3 +1,10 @@
+ config PINCTRL_BCM63XX
+ bool
+ select GPIO_GENERIC
++
++config PINCTRL_BCM6328
++ bool "BCM6328 pincontrol driver" if COMPILE_TEST
++ select PINMUX
++ select PINCONF
++ select PINCTRL_BCM63XX
++ select GENERIC_PINCONF
+--- a/drivers/pinctrl/bcm63xx/Makefile
++++ b/drivers/pinctrl/bcm63xx/Makefile
+@@ -1 +1,2 @@
+ obj-$(CONFIG_PINCTRL_BCM63XX) += pinctrl-bcm63xx.o
++obj-$(CONFIG_PINCTRL_BCM6328) += pinctrl-bcm6328.o
+--- /dev/null
++++ b/drivers/pinctrl/bcm63xx/pinctrl-bcm6328.c
+@@ -0,0 +1,456 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License. See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2016 Jonas Gorski <jonas.gorski@gmail.com>
++ */
++
++#include <linux/bitops.h>
++#include <linux/gpio.h>
++#include <linux/kernel.h>
++#include <linux/slab.h>
++#include <linux/spinlock.h>
++#include <linux/of.h>
++#include <linux/of_gpio.h>
++#include <linux/platform_device.h>
++
++#include <linux/pinctrl/machine.h>
++#include <linux/pinctrl/pinconf.h>
++#include <linux/pinctrl/pinconf-generic.h>
++#include <linux/pinctrl/pinmux.h>
++
++#include "../core.h"
++#include "../pinctrl-utils.h"
++
++#include "pinctrl-bcm63xx.h"
++
++#define BCM6328_MUX_LO_REG 0x4
++#define BCM6328_MUX_HI_REG 0x0
++#define BCM6328_MUX_OTHER_REG 0xc
++
++#define BCM6328_NGPIO 32
++
++struct bcm6328_pingroup {
++ const char *name;
++ const unsigned * const pins;
++ const unsigned num_pins;
++};
++
++struct bcm6328_function {
++ const char *name;
++ const char * const *groups;
++ const unsigned num_groups;
++
++ unsigned mode_val:1;
++ unsigned mux_val:2;
++};
++
++struct bcm6328_pinctrl {
++ struct pinctrl_dev *pctldev;
++ struct pinctrl_desc desc;
++
++ void __iomem *mode;
++ void __iomem *mux[3];
++
++ /* register access lock */
++ spinlock_t lock;
++
++ struct gpio_chip gpio;
++};
++
++static const struct pinctrl_pin_desc bcm6328_pins[] = {
++ PINCTRL_PIN(0, "gpio0"),
++ PINCTRL_PIN(1, "gpio1"),
++ PINCTRL_PIN(2, "gpio2"),
++ PINCTRL_PIN(3, "gpio3"),
++ PINCTRL_PIN(4, "gpio4"),
++ PINCTRL_PIN(5, "gpio5"),
++ PINCTRL_PIN(6, "gpio6"),
++ PINCTRL_PIN(7, "gpio7"),
++ PINCTRL_PIN(8, "gpio8"),
++ PINCTRL_PIN(9, "gpio9"),
++ PINCTRL_PIN(10, "gpio10"),
++ PINCTRL_PIN(11, "gpio11"),
++ PINCTRL_PIN(12, "gpio12"),
++ PINCTRL_PIN(13, "gpio13"),
++ PINCTRL_PIN(14, "gpio14"),
++ PINCTRL_PIN(15, "gpio15"),
++ PINCTRL_PIN(16, "gpio16"),
++ PINCTRL_PIN(17, "gpio17"),
++ PINCTRL_PIN(18, "gpio18"),
++ PINCTRL_PIN(19, "gpio19"),
++ PINCTRL_PIN(20, "gpio20"),
++ PINCTRL_PIN(21, "gpio21"),
++ PINCTRL_PIN(22, "gpio22"),
++ PINCTRL_PIN(23, "gpio23"),
++ PINCTRL_PIN(24, "gpio24"),
++ PINCTRL_PIN(25, "gpio25"),
++ PINCTRL_PIN(26, "gpio26"),
++ PINCTRL_PIN(27, "gpio27"),
++ PINCTRL_PIN(28, "gpio28"),
++ PINCTRL_PIN(29, "gpio29"),
++ PINCTRL_PIN(30, "gpio30"),
++ PINCTRL_PIN(31, "gpio31"),
++
++ /*
++ * No idea where they really are; so let's put them according
++ * to their mux offsets.
++ */
++ PINCTRL_PIN(36, "hsspi_cs1"),
++ PINCTRL_PIN(38, "usb_p2"),
++};
++
++static unsigned gpio0_pins[] = { 0 };
++static unsigned gpio1_pins[] = { 1 };
++static unsigned gpio2_pins[] = { 2 };
++static unsigned gpio3_pins[] = { 3 };
++static unsigned gpio4_pins[] = { 4 };
++static unsigned gpio5_pins[] = { 5 };
++static unsigned gpio6_pins[] = { 6 };
++static unsigned gpio7_pins[] = { 7 };
++static unsigned gpio8_pins[] = { 8 };
++static unsigned gpio9_pins[] = { 9 };
++static unsigned gpio10_pins[] = { 10 };
++static unsigned gpio11_pins[] = { 11 };
++static unsigned gpio12_pins[] = { 12 };
++static unsigned gpio13_pins[] = { 13 };
++static unsigned gpio14_pins[] = { 14 };
++static unsigned gpio15_pins[] = { 15 };
++static unsigned gpio16_pins[] = { 16 };
++static unsigned gpio17_pins[] = { 17 };
++static unsigned gpio18_pins[] = { 18 };
++static unsigned gpio19_pins[] = { 19 };
++static unsigned gpio20_pins[] = { 20 };
++static unsigned gpio21_pins[] = { 21 };
++static unsigned gpio22_pins[] = { 22 };
++static unsigned gpio23_pins[] = { 23 };
++static unsigned gpio24_pins[] = { 24 };
++static unsigned gpio25_pins[] = { 25 };
++static unsigned gpio26_pins[] = { 26 };
++static unsigned gpio27_pins[] = { 27 };
++static unsigned gpio28_pins[] = { 28 };
++static unsigned gpio29_pins[] = { 29 };
++static unsigned gpio30_pins[] = { 30 };
++static unsigned gpio31_pins[] = { 31 };
++
++static unsigned hsspi_cs1_pins[] = { 36 };
++static unsigned usb_port1_pins[] = { 38 };
++
++#define BCM6328_GROUP(n) \
++ { \
++ .name = #n, \
++ .pins = n##_pins, \
++ .num_pins = ARRAY_SIZE(n##_pins), \
++ }
++
++static struct bcm6328_pingroup bcm6328_groups[] = {
++ BCM6328_GROUP(gpio0),
++ BCM6328_GROUP(gpio1),
++ BCM6328_GROUP(gpio2),
++ BCM6328_GROUP(gpio3),
++ BCM6328_GROUP(gpio4),
++ BCM6328_GROUP(gpio5),
++ BCM6328_GROUP(gpio6),
++ BCM6328_GROUP(gpio7),
++ BCM6328_GROUP(gpio8),
++ BCM6328_GROUP(gpio9),
++ BCM6328_GROUP(gpio10),
++ BCM6328_GROUP(gpio11),
++ BCM6328_GROUP(gpio12),
++ BCM6328_GROUP(gpio13),
++ BCM6328_GROUP(gpio14),
++ BCM6328_GROUP(gpio15),
++ BCM6328_GROUP(gpio16),
++ BCM6328_GROUP(gpio17),
++ BCM6328_GROUP(gpio18),
++ BCM6328_GROUP(gpio19),
++ BCM6328_GROUP(gpio20),
++ BCM6328_GROUP(gpio21),
++ BCM6328_GROUP(gpio22),
++ BCM6328_GROUP(gpio23),
++ BCM6328_GROUP(gpio24),
++ BCM6328_GROUP(gpio25),
++ BCM6328_GROUP(gpio26),
++ BCM6328_GROUP(gpio27),
++ BCM6328_GROUP(gpio28),
++ BCM6328_GROUP(gpio29),
++ BCM6328_GROUP(gpio30),
++ BCM6328_GROUP(gpio31),
++
++ BCM6328_GROUP(hsspi_cs1),
++ BCM6328_GROUP(usb_port1),
++};
++
++/* GPIO_MODE */
++static const char * const led_groups[] = {
++ "gpio0",
++ "gpio1",
++ "gpio2",
++ "gpio3",
++ "gpio4",
++ "gpio5",
++ "gpio6",
++ "gpio7",
++ "gpio8",
++ "gpio9",
++ "gpio10",
++ "gpio11",
++ "gpio12",
++ "gpio13",
++ "gpio14",
++ "gpio15",
++ "gpio16",
++ "gpio17",
++ "gpio18",
++ "gpio19",
++ "gpio20",
++ "gpio21",
++ "gpio22",
++ "gpio23",
++};
++
++/* PINMUX_SEL */
++static const char * const serial_led_data_groups[] = {
++ "gpio6",
++};
++
++static const char * const serial_led_clk_groups[] = {
++ "gpio7",
++};
++
++static const char * const inet_act_led_groups[] = {
++ "gpio11",
++};
++
++static const char * const pcie_clkreq_groups[] = {
++ "gpio16",
++};
++
++static const char * const ephy0_act_led_groups[] = {
++ "gpio25",
++};
++
++static const char * const ephy1_act_led_groups[] = {
++ "gpio26",
++};
++
++static const char * const ephy2_act_led_groups[] = {
++ "gpio27",
++};
++
++static const char * const ephy3_act_led_groups[] = {
++ "gpio28",
++};
++
++static const char * const hsspi_cs1_groups[] = {
++ "hsspi_cs1"
++};
++
++static const char * const usb_host_port_groups[] = {
++ "usb_port1",
++};
++
++static const char * const usb_device_port_groups[] = {
++ "usb_port1",
++};
++
++#define BCM6328_MODE_FUN(n) \
++ { \
++ .name = #n, \
++ .groups = n##_groups, \
++ .num_groups = ARRAY_SIZE(n##_groups), \
++ .mode_val = 1, \
++ }
++
++#define BCM6328_MUX_FUN(n, mux) \
++ { \
++ .name = #n, \
++ .groups = n##_groups, \
++ .num_groups = ARRAY_SIZE(n##_groups), \
++ .mux_val = mux, \
++ }
++
++static const struct bcm6328_function bcm6328_funcs[] = {
++ BCM6328_MODE_FUN(led),
++ BCM6328_MUX_FUN(serial_led_data, 2),
++ BCM6328_MUX_FUN(serial_led_clk, 2),
++ BCM6328_MUX_FUN(inet_act_led, 1),
++ BCM6328_MUX_FUN(pcie_clkreq, 2),
++ BCM6328_MUX_FUN(ephy0_act_led, 1),
++ BCM6328_MUX_FUN(ephy1_act_led, 1),
++ BCM6328_MUX_FUN(ephy2_act_led, 1),
++ BCM6328_MUX_FUN(ephy3_act_led, 1),
++ BCM6328_MUX_FUN(hsspi_cs1, 2),
++ BCM6328_MUX_FUN(usb_host_port, 1),
++ BCM6328_MUX_FUN(usb_device_port, 2),
++};
++
++static int bcm6328_pinctrl_get_group_count(struct pinctrl_dev *pctldev)
++{
++ return ARRAY_SIZE(bcm6328_groups);
++}
++
++static const char *bcm6328_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
++ unsigned group)
++{
++ return bcm6328_groups[group].name;
++}
++
++static int bcm6328_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
++ unsigned group, const unsigned **pins,
++ unsigned *num_pins)
++{
++ *pins = bcm6328_groups[group].pins;
++ *num_pins = bcm6328_groups[group].num_pins;
++
++ return 0;
++}
++
++static int bcm6328_pinctrl_get_func_count(struct pinctrl_dev *pctldev)
++{
++ return ARRAY_SIZE(bcm6328_funcs);
++}
++
++static const char *bcm6328_pinctrl_get_func_name(struct pinctrl_dev *pctldev,
++ unsigned selector)
++{
++ return bcm6328_funcs[selector].name;
++}
++
++static int bcm6328_pinctrl_get_groups(struct pinctrl_dev *pctldev,
++ unsigned selector,
++ const char * const **groups,
++ unsigned * const num_groups)
++{
++ *groups = bcm6328_funcs[selector].groups;
++ *num_groups = bcm6328_funcs[selector].num_groups;
++
++ return 0;
++}
++
++static void bcm6328_rmw_mux(struct bcm6328_pinctrl *pctl, unsigned pin,
++ u32 mode, u32 mux)
++{
++ unsigned long flags;
++ u32 reg;
++
++ spin_lock_irqsave(&pctl->lock, flags);
++ if (pin < 32) {
++ reg = __raw_readl(pctl->mode);
++ reg &= ~BIT(pin);
++ if (mode)
++ reg |= BIT(pin);
++ __raw_writel(reg, pctl->mode);
++ }
++
++ reg = __raw_readl(pctl->mux[pin / 16]);
++ reg &= ~(3UL << ((pin % 16) * 2));
++ reg |= mux << ((pin % 16) * 2);
++ __raw_writel(reg, pctl->mux[pin / 16]);
++
++ spin_unlock_irqrestore(&pctl->lock, flags);
++}
++
++static int bcm6328_pinctrl_set_mux(struct pinctrl_dev *pctldev,
++ unsigned selector, unsigned group)
++{
++ struct bcm6328_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
++ const struct bcm6328_pingroup *grp = &bcm6328_groups[group];
++ const struct bcm6328_function *f = &bcm6328_funcs[selector];
++
++ bcm6328_rmw_mux(pctl, grp->pins[0], f->mode_val, f->mux_val);
++
++ return 0;
++}
++
++static int bcm6328_gpio_request_enable(struct pinctrl_dev *pctldev,
++ struct pinctrl_gpio_range *range,
++ unsigned offset)
++{
++ struct bcm6328_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
++
++ /* disable all functions using this pin */
++ bcm6328_rmw_mux(pctl, offset, 0, 0);
++
++ return 0;
++}
++
++static struct pinctrl_ops bcm6328_pctl_ops = {
++ .get_groups_count = bcm6328_pinctrl_get_group_count,
++ .get_group_name = bcm6328_pinctrl_get_group_name,
++ .get_group_pins = bcm6328_pinctrl_get_group_pins,
++#ifdef CONFIG_OF
++ .dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
++ .dt_free_map = pinctrl_utils_free_map,
++#endif
++};
++
++static struct pinmux_ops bcm6328_pmx_ops = {
++ .get_functions_count = bcm6328_pinctrl_get_func_count,
++ .get_function_name = bcm6328_pinctrl_get_func_name,
++ .get_function_groups = bcm6328_pinctrl_get_groups,
++ .set_mux = bcm6328_pinctrl_set_mux,
++ .gpio_request_enable = bcm6328_gpio_request_enable,
++ .strict = true,
++};
++
++static int bcm6328_pinctrl_probe(struct platform_device *pdev)
++{
++ struct bcm6328_pinctrl *pctl;
++ struct resource *res;
++ void __iomem *mode, *mux;
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mode");
++ mode = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(mode))
++ return PTR_ERR(mode);
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mux");
++ mux = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(mux))
++ return PTR_ERR(mux);
++
++ pctl = devm_kzalloc(&pdev->dev, sizeof(*pctl), GFP_KERNEL);
++ if (!pctl)
++ return -ENOMEM;
++
++ spin_lock_init(&pctl->lock);
++
++ pctl->mode = mode;
++ pctl->mux[0] = mux + BCM6328_MUX_LO_REG;
++ pctl->mux[1] = mux + BCM6328_MUX_HI_REG;
++ pctl->mux[2] = mux + BCM6328_MUX_OTHER_REG;
++
++ pctl->desc.name = dev_name(&pdev->dev);
++ pctl->desc.owner = THIS_MODULE;
++ pctl->desc.pctlops = &bcm6328_pctl_ops;
++ pctl->desc.pmxops = &bcm6328_pmx_ops;
++
++ pctl->desc.npins = ARRAY_SIZE(bcm6328_pins);
++ pctl->desc.pins = bcm6328_pins;
++
++ platform_set_drvdata(pdev, pctl);
++
++ pctl->pctldev = bcm63xx_pinctrl_register(pdev, &pctl->desc, pctl,
++ &pctl->gpio, BCM6328_NGPIO);
++ if (IS_ERR(pctl->pctldev))
++ return PTR_ERR(pctl->pctldev);
++
++ return 0;
++}
++
++static const struct of_device_id bcm6328_pinctrl_match[] = {
++ { .compatible = "brcm,bcm6328-pinctrl", },
++ { },
++};
++
++static struct platform_driver bcm6328_pinctrl_driver = {
++ .probe = bcm6328_pinctrl_probe,
++ .driver = {
++ .name = "bcm6328-pinctrl",
++ .of_match_table = bcm6328_pinctrl_match,
++ },
++};
++
++builtin_platform_driver(bcm6328_pinctrl_driver);
--- /dev/null
+From 962c46bf7f43df730e2d3698930e77958cc6b191 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Wed, 27 Jul 2016 11:35:45 +0200
+Subject: [PATCH 04/16] Documentation: add BCM6348 pincontroller binding
+ documentation
+
+Add binding documentation for the pincontrol core found in BCM6348 SoCs.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ .../bindings/pinctrl/brcm,bcm6348-pinctrl.txt | 32 ++++++++++++++++++++++
+ 1 file changed, 32 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/pinctrl/brcm,bcm6348-pinctrl.txt
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6348-pinctrl.txt
+@@ -0,0 +1,32 @@
++* Broadcom BCM6348 pin controller
++
++Required properties:
++- compatible: Must be "brcm,bcm6348-pinctrl".
++- reg: register Specifiers of dirout, dat, mode registers.
++- reg-names: Must be "dirout", "dat", "mode".
++- gpio-controller: Identifies this node as a GPIO controller.
++- #gpio-cells: Must be <2>.
++
++Example:
++
++pinctrl: pin-controller@fffe0080 {
++ compatible = "brcm,bcm6348-pinctrl";
++ reg = <0xfffe0080 0x8>,
++ <0xfffe0088 0x8>,
++ <0xfffe0098 0x4>;
++ reg-names = "dirout", "dat", "mode";
++
++ gpio-controller;
++ #gpio-cells = <2>;
++};
++
++Available pins/groups and functions:
++
++name pins functions
++-----------------------------------------------------------
++group0 32-36 ext_mii, utopia, diag
++group1 22-31 ext_ephy, mii_snoop, mii_pccard,
++ spi_master_uart, utopia, diag
++group2 16-21 pci, diag
++group3 8-15 ext_mii, utopia
++group4 0-7 ext_ephy, mii_snoop, legacy_led, diag
--- /dev/null
+From 45444cb631555e2dc16b95d779b10aa075c7482e Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Fri, 24 Jun 2016 22:14:13 +0200
+Subject: [PATCH 05/16] pinctrl: add a pincontrol driver for BCM6348
+
+Add a pincotrol driver for BCM6348. BCM6348 allow muxing five groups of
+up to ten gpios into fourteen potential functions. It does not allow
+muxing individual pins. Some functions require more than one group to be
+muxed to the same function.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ drivers/pinctrl/bcm63xx/Kconfig | 7 +
+ drivers/pinctrl/bcm63xx/Makefile | 1 +
+ drivers/pinctrl/bcm63xx/pinctrl-bcm6348.c | 392 ++++++++++++++++++++++++++++++
+ 3 files changed, 400 insertions(+)
+ create mode 100644 drivers/pinctrl/bcm63xx/pinctrl-bcm6348.c
+
+--- a/drivers/pinctrl/bcm63xx/Kconfig
++++ b/drivers/pinctrl/bcm63xx/Kconfig
+@@ -8,3 +8,10 @@ config PINCTRL_BCM6328
+ select PINCONF
+ select PINCTRL_BCM63XX
+ select GENERIC_PINCONF
++
++config PINCTRL_BCM6348
++ bool "BCM6348 pincontrol driver" if COMPILE_TEST
++ select PINMUX
++ select PINCONF
++ select PINCTRL_BCM63XX
++ select GENERIC_PINCONF
+--- a/drivers/pinctrl/bcm63xx/Makefile
++++ b/drivers/pinctrl/bcm63xx/Makefile
+@@ -1,2 +1,3 @@
+ obj-$(CONFIG_PINCTRL_BCM63XX) += pinctrl-bcm63xx.o
+ obj-$(CONFIG_PINCTRL_BCM6328) += pinctrl-bcm6328.o
++obj-$(CONFIG_PINCTRL_BCM6348) += pinctrl-bcm6348.o
+--- /dev/null
++++ b/drivers/pinctrl/bcm63xx/pinctrl-bcm6348.c
+@@ -0,0 +1,392 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License. See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2016 Jonas Gorski <jonas.gorski@gmail.com>
++ */
++
++#include <linux/kernel.h>
++#include <linux/spinlock.h>
++#include <linux/bitops.h>
++#include <linux/gpio.h>
++#include <linux/of.h>
++#include <linux/of_gpio.h>
++#include <linux/slab.h>
++#include <linux/platform_device.h>
++
++#include <linux/pinctrl/machine.h>
++#include <linux/pinctrl/pinconf.h>
++#include <linux/pinctrl/pinconf-generic.h>
++#include <linux/pinctrl/pinmux.h>
++
++#include "../core.h"
++#include "../pinctrl-utils.h"
++
++#include "pinctrl-bcm63xx.h"
++
++#define BCM6348_NGPIO 37
++
++#define MAX_GROUP 4
++#define PINS_PER_GROUP 8
++#define PIN_TO_GROUP(pin) (MAX_GROUP - ((pin) / PINS_PER_GROUP))
++#define GROUP_SHIFT(pin) (PIN_TO_GROUP(pin) * 4)
++#define GROUP_MASK(pin) (0xf << GROUP_SHIFT(pin))
++
++struct bcm6348_pingroup {
++ const char *name;
++ const unsigned * const pins;
++ const unsigned num_pins;
++};
++
++struct bcm6348_function {
++ const char *name;
++ const char * const *groups;
++ const unsigned num_groups;
++ unsigned int value;
++};
++
++struct bcm6348_pinctrl {
++ struct pinctrl_dev *pctldev;
++ struct pinctrl_desc desc;
++
++ void __iomem *mode;
++
++ /* register access lock */
++ spinlock_t lock;
++
++ struct gpio_chip gpio[2];
++};
++
++#define BCM6348_PIN(a, b, group) \
++ { \
++ .number = a, \
++ .name = b, \
++ .drv_data = (void *)(group), \
++ }
++
++static const struct pinctrl_pin_desc bcm6348_pins[] = {
++ BCM6348_PIN(0, "gpio0", 4),
++ BCM6348_PIN(1, "gpio1", 4),
++ BCM6348_PIN(2, "gpio2", 4),
++ BCM6348_PIN(3, "gpio3", 4),
++ BCM6348_PIN(4, "gpio4", 4),
++ BCM6348_PIN(5, "gpio5", 4),
++ BCM6348_PIN(6, "gpio6", 4),
++ BCM6348_PIN(7, "gpio7", 4),
++ BCM6348_PIN(8, "gpio8", 3),
++ BCM6348_PIN(9, "gpio9", 3),
++ BCM6348_PIN(10, "gpio10", 3),
++ BCM6348_PIN(11, "gpio11", 3),
++ BCM6348_PIN(12, "gpio12", 3),
++ BCM6348_PIN(13, "gpio13", 3),
++ BCM6348_PIN(14, "gpio14", 3),
++ BCM6348_PIN(15, "gpio15", 3),
++ BCM6348_PIN(16, "gpio16", 2),
++ BCM6348_PIN(17, "gpio17", 2),
++ BCM6348_PIN(18, "gpio18", 2),
++ BCM6348_PIN(19, "gpio19", 2),
++ BCM6348_PIN(20, "gpio20", 2),
++ BCM6348_PIN(21, "gpio21", 2),
++ BCM6348_PIN(22, "gpio22", 1),
++ BCM6348_PIN(23, "gpio23", 1),
++ BCM6348_PIN(24, "gpio24", 1),
++ BCM6348_PIN(25, "gpio25", 1),
++ BCM6348_PIN(26, "gpio26", 1),
++ BCM6348_PIN(27, "gpio27", 1),
++ BCM6348_PIN(28, "gpio28", 1),
++ BCM6348_PIN(29, "gpio29", 1),
++ BCM6348_PIN(30, "gpio30", 1),
++ BCM6348_PIN(31, "gpio31", 1),
++ BCM6348_PIN(32, "gpio32", 0),
++ BCM6348_PIN(33, "gpio33", 0),
++ BCM6348_PIN(34, "gpio34", 0),
++ BCM6348_PIN(35, "gpio35", 0),
++ BCM6348_PIN(36, "gpio36", 0),
++};
++
++enum bcm6348_muxes {
++ BCM6348_MUX_GPIO = 0,
++ BCM6348_MUX_EXT_EPHY,
++ BCM6348_MUX_MII_SNOOP,
++ BCM6348_MUX_LEGACY_LED,
++ BCM6348_MUX_MII_PCCARD,
++ BCM6348_MUX_PCI,
++ BCM6348_MUX_SPI_MASTER_UART,
++ BCM6348_MUX_EXT_MII,
++ BCM6348_MUX_UTOPIA,
++ BCM6348_MUX_DIAG,
++};
++
++static unsigned group0_pins[] = {
++ 32, 33, 34, 35, 36,
++};
++
++static unsigned group1_pins[] = {
++ 22, 23, 24, 25, 26, 27, 28, 29, 30, 31,
++};
++
++static unsigned group2_pins[] = {
++ 16, 17, 18, 19, 20, 21,
++};
++
++static unsigned group3_pins[] = {
++ 8, 9, 10, 11, 12, 13, 14, 15,
++};
++
++static unsigned group4_pins[] = {
++ 0, 1, 2, 3, 4, 5, 6, 7,
++};
++
++#define BCM6348_GROUP(n) \
++ { \
++ .name = #n, \
++ .pins = n##_pins, \
++ .num_pins = ARRAY_SIZE(n##_pins), \
++ } \
++
++static struct bcm6348_pingroup bcm6348_groups[] = {
++ BCM6348_GROUP(group0),
++ BCM6348_GROUP(group1),
++ BCM6348_GROUP(group2),
++ BCM6348_GROUP(group3),
++ BCM6348_GROUP(group4),
++};
++
++static const char * const ext_mii_groups[] = {
++ "group0",
++ "group3",
++};
++
++static const char * const ext_ephy_groups[] = {
++ "group1",
++ "group4"
++};
++
++static const char * const mii_snoop_groups[] = {
++ "group1",
++ "group4",
++};
++
++static const char * const legacy_led_groups[] = {
++ "group4",
++};
++
++static const char * const mii_pccard_groups[] = {
++ "group1",
++};
++
++static const char * const pci_groups[] = {
++ "group2",
++};
++
++static const char * const spi_master_uart_groups[] = {
++ "group1",
++};
++
++static const char * const utopia_groups[] = {
++ "group0",
++ "group1",
++ "group3",
++};
++
++static const char * const diag_groups[] = {
++ "group0",
++ "group1",
++ "group2",
++ "group4",
++};
++
++#define BCM6348_FUN(n, f) \
++ { \
++ .name = #n, \
++ .groups = n##_groups, \
++ .num_groups = ARRAY_SIZE(n##_groups), \
++ .value = BCM6348_MUX_##f, \
++ }
++
++static const struct bcm6348_function bcm6348_funcs[] = {
++ BCM6348_FUN(ext_mii, EXT_MII),
++ BCM6348_FUN(ext_ephy, EXT_EPHY),
++ BCM6348_FUN(mii_snoop, MII_SNOOP),
++ BCM6348_FUN(legacy_led, LEGACY_LED),
++ BCM6348_FUN(mii_pccard, MII_PCCARD),
++ BCM6348_FUN(pci, PCI),
++ BCM6348_FUN(spi_master_uart, SPI_MASTER_UART),
++ BCM6348_FUN(utopia, UTOPIA),
++ BCM6348_FUN(diag, DIAG),
++};
++
++static int bcm6348_pinctrl_get_group_count(struct pinctrl_dev *pctldev)
++{
++ return ARRAY_SIZE(bcm6348_groups);
++}
++
++static const char *bcm6348_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
++ unsigned group)
++{
++ return bcm6348_groups[group].name;
++}
++
++static int bcm6348_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
++ unsigned group, const unsigned **pins,
++ unsigned *num_pins)
++{
++ *pins = bcm6348_groups[group].pins;
++ *num_pins = bcm6348_groups[group].num_pins;
++
++ return 0;
++}
++
++static int bcm6348_pinctrl_get_func_count(struct pinctrl_dev *pctldev)
++{
++ return ARRAY_SIZE(bcm6348_funcs);
++}
++
++static const char *bcm6348_pinctrl_get_func_name(struct pinctrl_dev *pctldev,
++ unsigned selector)
++{
++ return bcm6348_funcs[selector].name;
++}
++
++static int bcm6348_pinctrl_get_groups(struct pinctrl_dev *pctldev,
++ unsigned selector,
++ const char * const **groups,
++ unsigned * const num_groups)
++{
++ *groups = bcm6348_funcs[selector].groups;
++ *num_groups = bcm6348_funcs[selector].num_groups;
++
++ return 0;
++}
++
++static void bcm6348_rmw_mux(struct bcm6348_pinctrl *pctl, u32 mask, u32 val)
++{
++ unsigned long flags;
++ u32 reg;
++
++ spin_lock_irqsave(&pctl->lock, flags);
++
++ reg = __raw_readl(pctl->mode);
++ reg &= ~mask;
++ reg |= val & mask;
++ __raw_writel(reg, pctl->mode);
++
++ spin_unlock_irqrestore(&pctl->lock, flags);
++}
++
++static int bcm6348_pinctrl_set_mux(struct pinctrl_dev *pctldev,
++ unsigned selector, unsigned group)
++{
++ struct bcm6348_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
++ const struct bcm6348_pingroup *grp = &bcm6348_groups[group];
++ const struct bcm6348_function *f = &bcm6348_funcs[selector];
++ u32 group_num, mask, val;
++
++ /*
++ * pins n..(n+7) share the same group, so we only need to look at
++ * the first pin.
++ */
++ group_num = (unsigned long)bcm6348_pins[grp->pins[0]].drv_data;
++ mask = GROUP_MASK(group_num);
++ val = f->value << GROUP_SHIFT(group_num);
++
++ bcm6348_rmw_mux(pctl, mask, val);
++
++ return 0;
++}
++
++static int bcm6348_gpio_request_enable(struct pinctrl_dev *pctldev,
++ struct pinctrl_gpio_range *range,
++ unsigned offset)
++{
++ struct bcm6348_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
++ struct pin_desc *desc;
++ u32 mask;
++
++ /* don't reconfigure if already muxed */
++ desc = pin_desc_get(pctldev, offset);
++ if (desc->mux_usecount)
++ return 0;
++
++ mask = GROUP_MASK(offset);
++
++ /* disable all functions using this pin */
++ bcm6348_rmw_mux(pctl, mask, 0);
++
++ return 0;
++}
++
++static struct pinctrl_ops bcm6348_pctl_ops = {
++ .get_groups_count = bcm6348_pinctrl_get_group_count,
++ .get_group_name = bcm6348_pinctrl_get_group_name,
++ .get_group_pins = bcm6348_pinctrl_get_group_pins,
++#ifdef CONFIG_OF
++ .dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
++ .dt_free_map = pinctrl_utils_free_map,
++#endif
++};
++
++static struct pinmux_ops bcm6348_pmx_ops = {
++ .get_functions_count = bcm6348_pinctrl_get_func_count,
++ .get_function_name = bcm6348_pinctrl_get_func_name,
++ .get_function_groups = bcm6348_pinctrl_get_groups,
++ .set_mux = bcm6348_pinctrl_set_mux,
++ .gpio_request_enable = bcm6348_gpio_request_enable,
++ .strict = true,
++};
++
++static int bcm6348_pinctrl_probe(struct platform_device *pdev)
++{
++ struct bcm6348_pinctrl *pctl;
++ struct resource *res;
++ void __iomem *mode;
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mode");
++ mode = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(mode))
++ return PTR_ERR(mode);
++
++ pctl = devm_kzalloc(&pdev->dev, sizeof(*pctl), GFP_KERNEL);
++ if (!pctl)
++ return -ENOMEM;
++
++ spin_lock_init(&pctl->lock);
++
++ pctl->mode = mode;
++
++ /* disable all muxes by default */
++ __raw_writel(0, pctl->mode);
++
++ pctl->desc.name = dev_name(&pdev->dev);
++ pctl->desc.owner = THIS_MODULE;
++ pctl->desc.pctlops = &bcm6348_pctl_ops;
++ pctl->desc.pmxops = &bcm6348_pmx_ops;
++
++ pctl->desc.npins = ARRAY_SIZE(bcm6348_pins);
++ pctl->desc.pins = bcm6348_pins;
++
++ platform_set_drvdata(pdev, pctl);
++
++ pctl->pctldev = bcm63xx_pinctrl_register(pdev, &pctl->desc, pctl,
++ pctl->gpio, BCM6348_NGPIO);
++ if (IS_ERR(pctl->pctldev))
++ return PTR_ERR(pctl->pctldev);
++
++ return 0;
++}
++
++static const struct of_device_id bcm6348_pinctrl_match[] = {
++ { .compatible = "brcm,bcm6348-pinctrl", },
++ { },
++};
++
++static struct platform_driver bcm6348_pinctrl_driver = {
++ .probe = bcm6348_pinctrl_probe,
++ .driver = {
++ .name = "bcm6348-pinctrl",
++ .of_match_table = bcm6348_pinctrl_match,
++ },
++};
++
++builtin_platform_driver(bcm6348_pinctrl_driver);
--- /dev/null
+From c7c8fa7f5b5ee9bea751fa7bdae8ff4acde8f26e Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Wed, 27 Jul 2016 11:36:00 +0200
+Subject: [PATCH 06/16] Documentation: add BCM6358 pincontroller binding
+ documentation
+
+Add binding documentation for the pincontrol core found in BCM6358 SoCs.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ .../bindings/pinctrl/brcm,bcm6358-pinctrl.txt | 44 ++++++++++++++++++++++
+ 1 file changed, 44 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/pinctrl/brcm,bcm6358-pinctrl.txt
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6358-pinctrl.txt
+@@ -0,0 +1,44 @@
++* Broadcom BCM6358 pin controller
++
++Required properties:
++- compatible: Must be "brcm,bcm6358-pinctrl".
++- reg: Register specifiers of dirout, dat registers.
++- reg-names: Must be "dirout", "dat".
++- brcm,gpiomode: Phandle to the shared gpiomode register.
++- gpio-controller: Identifies this node as a gpio-controller.
++- #gpio-cells: Must be <2>.
++
++Example:
++
++pinctrl: pin-controller@fffe0080 {
++ compatible = "brcm,bcm6358-pinctrl";
++ reg = <0xfffe0080 0x8>,
++ <0xfffe0088 0x8>,
++ <0xfffe0098 0x4>;
++ reg-names = "dirout", "dat";
++ brcm,gpiomode = <&gpiomode>;
++
++ gpio-controller;
++ #gpio-cells = <2>;
++};
++
++gpiomode: syscon@fffe0098 {
++ compatible = "brcm,bcm6358-gpiomode", "syscon";
++ reg = <0xfffe0098 0x4>;
++ native-endian;
++};
++
++Available pins/groups and functions:
++
++name pins functions
++-----------------------------------------------------------
++ebi_cs_grp 30-31 ebi_cs
++uart1_grp 28-31 uart1
++spi_cs_grp 32-33 spi_cs
++async_modem_grp 12-15 async_modem
++legacy_led_grp 9-15 legacy_led
++serial_led_grp 6-7 serial_led
++led_grp 0-3 led
++utopia_grp 12-15, 22-31 utopia
++pwm_syn_clk_grp 8 pwm_syn_clk
++sys_irq_grp 5 sys_irq
--- /dev/null
+From fb00ef462f3f8b70ea8902151cc72810fe90b999 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Fri, 24 Jun 2016 22:16:01 +0200
+Subject: [PATCH 07/16] pinctrl: add a pincontrol driver for BCM6358
+
+Add a pincotrol driver for BCM6358. BCM6358 allow overlaying different
+functions onto the GPIO pins. It does not support configuring individual
+pins but only whole groups. These groups may overlap, and still require
+the directions to be set correctly in the GPIO register. In addition the
+functions register controls other, not directly mux related functions.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ drivers/pinctrl/bcm63xx/Kconfig | 8 +
+ drivers/pinctrl/bcm63xx/Makefile | 1 +
+ drivers/pinctrl/bcm63xx/pinctrl-bcm6358.c | 393 ++++++++++++++++++++++++++++++
+ 3 files changed, 402 insertions(+)
+ create mode 100644 drivers/pinctrl/bcm63xx/pinctrl-bcm6358.c
+
+--- a/drivers/pinctrl/bcm63xx/Kconfig
++++ b/drivers/pinctrl/bcm63xx/Kconfig
+@@ -15,3 +15,11 @@ config PINCTRL_BCM6348
+ select PINCONF
+ select PINCTRL_BCM63XX
+ select GENERIC_PINCONF
++
++config PINCTRL_BCM6358
++ bool "BCM6358 pincontrol driver" if COMPILE_TEST
++ select PINMUX
++ select PINCONF
++ select PINCTRL_BCM63XX
++ select GENERIC_PINCONF
++ select MFD_SYSCON
+--- a/drivers/pinctrl/bcm63xx/Makefile
++++ b/drivers/pinctrl/bcm63xx/Makefile
+@@ -1,3 +1,4 @@
+ obj-$(CONFIG_PINCTRL_BCM63XX) += pinctrl-bcm63xx.o
+ obj-$(CONFIG_PINCTRL_BCM6328) += pinctrl-bcm6328.o
+ obj-$(CONFIG_PINCTRL_BCM6348) += pinctrl-bcm6348.o
++obj-$(CONFIG_PINCTRL_BCM6358) += pinctrl-bcm6358.o
+--- /dev/null
++++ b/drivers/pinctrl/bcm63xx/pinctrl-bcm6358.c
+@@ -0,0 +1,393 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License. See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2016 Jonas Gorski <jonas.gorski@gmail.com>
++ */
++
++#include <linux/kernel.h>
++#include <linux/bitops.h>
++#include <linux/gpio.h>
++#include <linux/gpio/driver.h>
++#include <linux/mfd/syscon.h>
++#include <linux/of.h>
++#include <linux/of_gpio.h>
++#include <linux/of_address.h>
++#include <linux/slab.h>
++#include <linux/regmap.h>
++#include <linux/platform_device.h>
++
++#include <linux/pinctrl/pinconf.h>
++#include <linux/pinctrl/pinconf-generic.h>
++#include <linux/pinctrl/pinmux.h>
++#include <linux/pinctrl/machine.h>
++
++#include "../core.h"
++#include "../pinctrl-utils.h"
++
++#include "pinctrl-bcm63xx.h"
++
++/* GPIO_MODE register */
++#define BCM6358_MODE_MUX_NONE 0
++
++/* overlays on gpio pins */
++#define BCM6358_MODE_MUX_EBI_CS BIT(5)
++#define BCM6358_MODE_MUX_UART1 BIT(6)
++#define BCM6358_MODE_MUX_SPI_CS BIT(7)
++#define BCM6358_MODE_MUX_ASYNC_MODEM BIT(8)
++#define BCM6358_MODE_MUX_LEGACY_LED BIT(9)
++#define BCM6358_MODE_MUX_SERIAL_LED BIT(10)
++#define BCM6358_MODE_MUX_LED BIT(11)
++#define BCM6358_MODE_MUX_UTOPIA BIT(12)
++#define BCM6358_MODE_MUX_CLKRST BIT(13)
++#define BCM6358_MODE_MUX_PWM_SYN_CLK BIT(14)
++#define BCM6358_MODE_MUX_SYS_IRQ BIT(15)
++
++#define BCM6358_NGPIO 40
++
++struct bcm6358_pingroup {
++ const char *name;
++ const unsigned * const pins;
++ const unsigned num_pins;
++
++ const u16 mode_val;
++
++ /* non-GPIO function muxes require the gpio direction to be set */
++ const u16 direction;
++};
++
++struct bcm6358_function {
++ const char *name;
++ const char * const *groups;
++ const unsigned num_groups;
++};
++
++struct bcm6358_pinctrl {
++ struct device *dev;
++ struct pinctrl_dev *pctldev;
++ struct pinctrl_desc desc;
++
++ struct regmap_field *overlays;
++
++ struct gpio_chip gpio[2];
++};
++
++#define BCM6358_GPIO_PIN(a, b, bit1, bit2, bit3) \
++ { \
++ .number = a, \
++ .name = b, \
++ .drv_data = (void *)(BCM6358_MODE_MUX_##bit1 | \
++ BCM6358_MODE_MUX_##bit2 | \
++ BCM6358_MODE_MUX_##bit3), \
++ }
++
++static const struct pinctrl_pin_desc bcm6358_pins[] = {
++ BCM6358_GPIO_PIN(0, "gpio0", LED, NONE, NONE),
++ BCM6358_GPIO_PIN(1, "gpio1", LED, NONE, NONE),
++ BCM6358_GPIO_PIN(2, "gpio2", LED, NONE, NONE),
++ BCM6358_GPIO_PIN(3, "gpio3", LED, NONE, NONE),
++ PINCTRL_PIN(4, "gpio4"),
++ BCM6358_GPIO_PIN(5, "gpio5", SYS_IRQ, NONE, NONE),
++ BCM6358_GPIO_PIN(6, "gpio6", SERIAL_LED, NONE, NONE),
++ BCM6358_GPIO_PIN(7, "gpio7", SERIAL_LED, NONE, NONE),
++ BCM6358_GPIO_PIN(8, "gpio8", PWM_SYN_CLK, NONE, NONE),
++ BCM6358_GPIO_PIN(9, "gpio09", LEGACY_LED, NONE, NONE),
++ BCM6358_GPIO_PIN(10, "gpio10", LEGACY_LED, NONE, NONE),
++ BCM6358_GPIO_PIN(11, "gpio11", LEGACY_LED, NONE, NONE),
++ BCM6358_GPIO_PIN(12, "gpio12", LEGACY_LED, ASYNC_MODEM, UTOPIA),
++ BCM6358_GPIO_PIN(13, "gpio13", LEGACY_LED, ASYNC_MODEM, UTOPIA),
++ BCM6358_GPIO_PIN(14, "gpio14", LEGACY_LED, ASYNC_MODEM, UTOPIA),
++ BCM6358_GPIO_PIN(15, "gpio15", LEGACY_LED, ASYNC_MODEM, UTOPIA),
++ PINCTRL_PIN(16, "gpio16"),
++ PINCTRL_PIN(17, "gpio17"),
++ PINCTRL_PIN(18, "gpio18"),
++ PINCTRL_PIN(19, "gpio19"),
++ PINCTRL_PIN(20, "gpio20"),
++ PINCTRL_PIN(21, "gpio21"),
++ BCM6358_GPIO_PIN(22, "gpio22", UTOPIA, NONE, NONE),
++ BCM6358_GPIO_PIN(23, "gpio23", UTOPIA, NONE, NONE),
++ BCM6358_GPIO_PIN(24, "gpio24", UTOPIA, NONE, NONE),
++ BCM6358_GPIO_PIN(25, "gpio25", UTOPIA, NONE, NONE),
++ BCM6358_GPIO_PIN(26, "gpio26", UTOPIA, NONE, NONE),
++ BCM6358_GPIO_PIN(27, "gpio27", UTOPIA, NONE, NONE),
++ BCM6358_GPIO_PIN(28, "gpio28", UTOPIA, UART1, NONE),
++ BCM6358_GPIO_PIN(29, "gpio29", UTOPIA, UART1, NONE),
++ BCM6358_GPIO_PIN(30, "gpio30", UTOPIA, UART1, EBI_CS),
++ BCM6358_GPIO_PIN(31, "gpio31", UTOPIA, UART1, EBI_CS),
++ BCM6358_GPIO_PIN(32, "gpio32", SPI_CS, NONE, NONE),
++ BCM6358_GPIO_PIN(33, "gpio33", SPI_CS, NONE, NONE),
++ PINCTRL_PIN(34, "gpio34"),
++ PINCTRL_PIN(35, "gpio35"),
++ PINCTRL_PIN(36, "gpio36"),
++ PINCTRL_PIN(37, "gpio37"),
++ PINCTRL_PIN(38, "gpio38"),
++ PINCTRL_PIN(39, "gpio39"),
++};
++
++static unsigned ebi_cs_grp_pins[] = { 30, 31 };
++
++static unsigned uart1_grp_pins[] = { 28, 29, 30, 31 };
++
++static unsigned spi_cs_grp_pins[] = { 32, 33 };
++
++static unsigned async_modem_grp_pins[] = { 12, 13, 14, 15 };
++
++static unsigned serial_led_grp_pins[] = { 6, 7 };
++
++static unsigned legacy_led_grp_pins[] = { 9, 10, 11, 12, 13, 14, 15 };
++
++static unsigned led_grp_pins[] = { 0, 1, 2, 3 };
++
++static unsigned utopia_grp_pins[] = {
++ 12, 13, 14, 15, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31,
++};
++
++static unsigned pwm_syn_clk_grp_pins[] = { 8 };
++
++static unsigned sys_irq_grp_pins[] = { 5 };
++
++#define BCM6358_GPIO_MUX_GROUP(n, bit, dir) \
++ { \
++ .name = #n, \
++ .pins = n##_pins, \
++ .num_pins = ARRAY_SIZE(n##_pins), \
++ .mode_val = BCM6358_MODE_MUX_##bit, \
++ .direction = dir, \
++ }
++
++static const struct bcm6358_pingroup bcm6358_groups[] = {
++ BCM6358_GPIO_MUX_GROUP(ebi_cs_grp, EBI_CS, 0x3),
++ BCM6358_GPIO_MUX_GROUP(uart1_grp, UART1, 0x2),
++ BCM6358_GPIO_MUX_GROUP(spi_cs_grp, SPI_CS, 0x6),
++ BCM6358_GPIO_MUX_GROUP(async_modem_grp, ASYNC_MODEM, 0x6),
++ BCM6358_GPIO_MUX_GROUP(legacy_led_grp, LEGACY_LED, 0x7f),
++ BCM6358_GPIO_MUX_GROUP(serial_led_grp, SERIAL_LED, 0x3),
++ BCM6358_GPIO_MUX_GROUP(led_grp, LED, 0xf),
++ BCM6358_GPIO_MUX_GROUP(utopia_grp, UTOPIA, 0x000f),
++ BCM6358_GPIO_MUX_GROUP(pwm_syn_clk_grp, PWM_SYN_CLK, 0x1),
++ BCM6358_GPIO_MUX_GROUP(sys_irq_grp, SYS_IRQ, 0x1),
++};
++
++static const char * const ebi_cs_groups[] = {
++ "ebi_cs_grp"
++};
++
++static const char * const uart1_groups[] = {
++ "uart1_grp"
++};
++
++static const char * const spi_cs_2_3_groups[] = {
++ "spi_cs_2_3_grp"
++};
++
++static const char * const async_modem_groups[] = {
++ "async_modem_grp"
++};
++
++static const char * const legacy_led_groups[] = {
++ "legacy_led_grp",
++};
++
++static const char * const serial_led_groups[] = {
++ "serial_led_grp",
++};
++
++static const char * const led_groups[] = {
++ "led_grp",
++};
++
++static const char * const clkrst_groups[] = {
++ "clkrst_grp",
++};
++
++static const char * const pwm_syn_clk_groups[] = {
++ "pwm_syn_clk_grp",
++};
++
++static const char * const sys_irq_groups[] = {
++ "sys_irq_grp",
++};
++
++#define BCM6358_FUN(n) \
++ { \
++ .name = #n, \
++ .groups = n##_groups, \
++ .num_groups = ARRAY_SIZE(n##_groups), \
++ }
++
++static const struct bcm6358_function bcm6358_funcs[] = {
++ BCM6358_FUN(ebi_cs),
++ BCM6358_FUN(uart1),
++ BCM6358_FUN(spi_cs_2_3),
++ BCM6358_FUN(async_modem),
++ BCM6358_FUN(legacy_led),
++ BCM6358_FUN(serial_led),
++ BCM6358_FUN(led),
++ BCM6358_FUN(clkrst),
++ BCM6358_FUN(pwm_syn_clk),
++ BCM6358_FUN(sys_irq),
++};
++
++static int bcm6358_pinctrl_get_group_count(struct pinctrl_dev *pctldev)
++{
++ return ARRAY_SIZE(bcm6358_groups);
++}
++
++static const char *bcm6358_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
++ unsigned group)
++{
++ return bcm6358_groups[group].name;
++}
++
++static int bcm6358_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
++ unsigned group, const unsigned **pins,
++ unsigned *num_pins)
++{
++ *pins = bcm6358_groups[group].pins;
++ *num_pins = bcm6358_groups[group].num_pins;
++
++ return 0;
++}
++
++static int bcm6358_pinctrl_get_func_count(struct pinctrl_dev *pctldev)
++{
++ return ARRAY_SIZE(bcm6358_funcs);
++}
++
++static const char *bcm6358_pinctrl_get_func_name(struct pinctrl_dev *pctldev,
++ unsigned selector)
++{
++ return bcm6358_funcs[selector].name;
++}
++
++static int bcm6358_pinctrl_get_groups(struct pinctrl_dev *pctldev,
++ unsigned selector,
++ const char * const **groups,
++ unsigned * const num_groups)
++{
++ *groups = bcm6358_funcs[selector].groups;
++ *num_groups = bcm6358_funcs[selector].num_groups;
++
++ return 0;
++}
++
++static int bcm6358_pinctrl_set_mux(struct pinctrl_dev *pctldev,
++ unsigned selector, unsigned group)
++{
++ struct bcm6358_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
++ const struct bcm6358_pingroup *grp = &bcm6358_groups[group];
++ u32 val = grp->mode_val;
++ u32 mask = val;
++ unsigned pin;
++
++ for (pin = 0; pin < grp->num_pins; pin++)
++ mask |= (unsigned long)bcm6358_pins[pin].drv_data;
++
++ regmap_field_update_bits(pctl->overlays, mask, val);
++
++ for (pin = 0; pin < grp->num_pins; pin++) {
++ int hw_gpio = bcm6358_pins[pin].number;
++ struct gpio_chip *gc = &pctl->gpio[hw_gpio / 32];
++
++ if (grp->direction & BIT(pin))
++ gc->direction_output(gc, hw_gpio % 32, 0);
++ else
++ gc->direction_input(gc, hw_gpio % 32);
++ }
++
++ return 0;
++}
++
++static int bcm6358_gpio_request_enable(struct pinctrl_dev *pctldev,
++ struct pinctrl_gpio_range *range,
++ unsigned offset)
++{
++ struct bcm6358_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
++ u32 mask;
++
++ mask = (unsigned long)bcm6358_pins[offset].drv_data;
++ if (!mask)
++ return 0;
++
++ /* disable all functions using this pin */
++ return regmap_field_update_bits(pctl->overlays, mask, 0);
++}
++
++static struct pinctrl_ops bcm6358_pctl_ops = {
++ .get_groups_count = bcm6358_pinctrl_get_group_count,
++ .get_group_name = bcm6358_pinctrl_get_group_name,
++ .get_group_pins = bcm6358_pinctrl_get_group_pins,
++#ifdef CONFIG_OF
++ .dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
++ .dt_free_map = pinctrl_utils_free_map,
++#endif
++};
++
++static struct pinmux_ops bcm6358_pmx_ops = {
++ .get_functions_count = bcm6358_pinctrl_get_func_count,
++ .get_function_name = bcm6358_pinctrl_get_func_name,
++ .get_function_groups = bcm6358_pinctrl_get_groups,
++ .set_mux = bcm6358_pinctrl_set_mux,
++ .gpio_request_enable = bcm6358_gpio_request_enable,
++ .strict = true,
++};
++
++static int bcm6358_pinctrl_probe(struct platform_device *pdev)
++{
++ struct bcm6358_pinctrl *pctl;
++ struct regmap *mode;
++ struct reg_field overlays = REG_FIELD(0, 0, 15);
++
++ if (pdev->dev.of_node)
++ mode = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
++ "brcm,gpiomode");
++ else
++ mode = syscon_regmap_lookup_by_pdevname("syscon.fffe0098");
++
++ if (IS_ERR(mode))
++ return PTR_ERR(mode);
++
++ pctl = devm_kzalloc(&pdev->dev, sizeof(*pctl), GFP_KERNEL);
++ if (!pctl)
++ return -ENOMEM;
++
++ pctl->overlays = devm_regmap_field_alloc(&pdev->dev, mode, overlays);
++ if (IS_ERR(pctl->overlays))
++ return PTR_ERR(pctl->overlays);
++
++ /* disable all muxes by default */
++ regmap_field_write(pctl->overlays, 0);
++
++ pctl->desc.name = dev_name(&pdev->dev);
++ pctl->desc.owner = THIS_MODULE;
++ pctl->desc.pctlops = &bcm6358_pctl_ops;
++ pctl->desc.pmxops = &bcm6358_pmx_ops;
++
++ pctl->desc.npins = ARRAY_SIZE(bcm6358_pins);
++ pctl->desc.pins = bcm6358_pins;
++
++ platform_set_drvdata(pdev, pctl);
++
++ pctl->pctldev = bcm63xx_pinctrl_register(pdev, &pctl->desc, pctl,
++ pctl->gpio, BCM6358_NGPIO);
++ if (IS_ERR(pctl->pctldev))
++ return PTR_ERR(pctl->pctldev);
++
++ return 0;
++}
++
++static const struct of_device_id bcm6358_pinctrl_match[] = {
++ { .compatible = "brcm,bcm6358-pinctrl", },
++ { },
++};
++
++static struct platform_driver bcm6358_pinctrl_driver = {
++ .probe = bcm6358_pinctrl_probe,
++ .driver = {
++ .name = "bcm6358-pinctrl",
++ .of_match_table = bcm6358_pinctrl_match,
++ },
++};
++
++builtin_platform_driver(bcm6358_pinctrl_driver);
--- /dev/null
+From ba03ea8ada2ca71c9095d96a1e4085c2c5cf0e69 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Wed, 27 Jul 2016 11:36:18 +0200
+Subject: [PATCH 08/16] Documentation: add BCM6362 pincontroller binding
+ documentation
+
+Add binding documentation for the pincontrol core found in BCM6362 SoCs.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ .../bindings/pinctrl/brcm,bcm6362-pinctrl.txt | 79 ++++++++++++++++++++++
+ 1 file changed, 79 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/pinctrl/brcm,bcm6362-pinctrl.txt
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6362-pinctrl.txt
+@@ -0,0 +1,79 @@
++* Broadcom BCM6362 pin controller
++
++Required properties:
++- compatible: Must be "brcm,bcm6362-pinctrl"
++- reg: Register specifiers of dirout, dat, led, mode, ctrl, basemode registers.
++- reg-names: Must be "dirout", "dat", "led", "mode", "ctrl", "basemode".
++- gpio-controller: Identifies this node as a GPIO controller.
++- #gpio-cells: Must be <2>.
++
++Example:
++
++pinctrl: pin-controller@10000080 {
++ compatible = "brcm,bcm6362-pinctrl";
++ reg = <0x10000080 0x8>,
++ <0x10000088 0x8>,
++ <0x10000090 0x4>,
++ <0x10000098 0x4>,
++ <0x1000009c 0x4>,
++ <0x100000b8 0x4>;
++ reg-names = "dirout", "dat", "led",
++ "mode", "ctrl", "basemode";
++
++ gpio-controller;
++ #gpio-cells = <2>;
++};
++
++Available pins/groups and functions:
++
++name pins functions
++-----------------------------------------------------------
++gpio0 0 led, usb_device_led
++gpio1 1 led, sys_irq
++gpio2 2 led, serial_led_clk
++gpio3 3 led, serial_led_data
++gpio4 4 led, robosw_led_data
++gpio5 5 led, robosw_led_clk
++gpio6 6 led, robosw_led0
++gpio7 7 led, robosw_led1
++gpio8 8 led, inet_led
++gpio9 9 led, spi_cs2
++gpio10 10 led, spi_cs3
++gpio11 11 led, ntr_pulse
++gpio12 12 led, uart1_scts
++gpio13 13 led, uart1_srts
++gpio14 14 led, uart1_sdin
++gpio15 15 led, uart1_sdout
++gpio16 16 led, adsl_spi_miso
++gpio17 17 led, adsl_spi_mosi
++gpio18 18 led, adsl_spi_clk
++gpio19 19 led, adsl_spi_cs
++gpio20 20 led, ephy0_led
++gpio21 21 led, ephy1_led
++gpio22 22 led, ephy2_led
++gpio23 23 led, ephy3_led
++gpio24 24 ext_irq0
++gpio25 25 ext_irq1
++gpio26 26 ext_irq2
++gpio27 27 ext_irq3
++gpio28 28 -
++gpio29 29 -
++gpio30 30 -
++gpio31 31 -
++gpio32 32 wifi
++gpio33 33 wifi
++gpio34 34 wifi
++gpio35 35 wifi
++gpio36 36 wifi
++gpio37 37 wifi
++gpio38 38 wifi
++gpio39 39 wifi
++gpio40 40 wifi
++gpio41 41 wifi
++gpio42 42 wifi
++gpio43 43 wifi
++gpio44 44 wifi
++gpio45 45 wifi
++gpio46 46 wifi
++gpio47 47 wifi
++nand_grp 8, 12-23, 27 nand
--- /dev/null
+From eea6b96701d734095e2f823f3a82d9b063f553ae Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Fri, 24 Jun 2016 22:17:20 +0200
+Subject: [PATCH 09/16] pinctrl: add a pincontrol driver for BCM6362
+
+Add a pincotrol driver for BCM6362. BCM6362 allows muxing individual
+GPIO pins to the LED controller, to be available by the integrated
+wifi, or other functions. It also supports overlay groups, of which
+only NAND is documented.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ drivers/pinctrl/bcm63xx/Kconfig | 7 +
+ drivers/pinctrl/bcm63xx/Makefile | 1 +
+ drivers/pinctrl/bcm63xx/pinctrl-bcm6362.c | 692 ++++++++++++++++++++++++++++++
+ 3 files changed, 700 insertions(+)
+ create mode 100644 drivers/pinctrl/bcm63xx/pinctrl-bcm6362.c
+
+--- a/drivers/pinctrl/bcm63xx/Kconfig
++++ b/drivers/pinctrl/bcm63xx/Kconfig
+@@ -23,3 +23,10 @@ config PINCTRL_BCM6358
+ select PINCTRL_BCM63XX
+ select GENERIC_PINCONF
+ select MFD_SYSCON
++
++config PINCTRL_BCM6362
++ bool "BCM6362 pincontrol driver" if COMPILE_TEST
++ select PINMUX
++ select PINCONF
++ select PINCTRL_BCM63XX
++ select GENERIC_PINCONF
+--- a/drivers/pinctrl/bcm63xx/Makefile
++++ b/drivers/pinctrl/bcm63xx/Makefile
+@@ -2,3 +2,4 @@ obj-$(CONFIG_PINCTRL_BCM63XX) += pinctrl
+ obj-$(CONFIG_PINCTRL_BCM6328) += pinctrl-bcm6328.o
+ obj-$(CONFIG_PINCTRL_BCM6348) += pinctrl-bcm6348.o
+ obj-$(CONFIG_PINCTRL_BCM6358) += pinctrl-bcm6358.o
++obj-$(CONFIG_PINCTRL_BCM6362) += pinctrl-bcm6362.o
+--- /dev/null
++++ b/drivers/pinctrl/bcm63xx/pinctrl-bcm6362.c
+@@ -0,0 +1,692 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License. See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2016 Jonas Gorski <jonas.gorski@gmail.com>
++ */
++
++#include <linux/kernel.h>
++#include <linux/spinlock.h>
++#include <linux/bitops.h>
++#include <linux/gpio.h>
++#include <linux/of.h>
++#include <linux/of_gpio.h>
++#include <linux/slab.h>
++#include <linux/platform_device.h>
++
++#include <linux/pinctrl/pinconf.h>
++#include <linux/pinctrl/pinconf-generic.h>
++#include <linux/pinctrl/pinmux.h>
++#include <linux/pinctrl/machine.h>
++
++#include "../core.h"
++#include "../pinctrl-utils.h"
++
++#include "pinctrl-bcm63xx.h"
++
++#define BCM6362_NGPIO 48
++
++/* GPIO_BASEMODE register */
++#define BASEMODE_NAND BIT(2)
++
++enum bcm6362_pinctrl_reg {
++ BCM6362_LEDCTRL,
++ BCM6362_MODE,
++ BCM6362_CTRL,
++ BCM6362_BASEMODE,
++};
++
++struct bcm6362_pingroup {
++ const char *name;
++ const unsigned * const pins;
++ const unsigned num_pins;
++};
++
++struct bcm6362_function {
++ const char *name;
++ const char * const *groups;
++ const unsigned num_groups;
++
++ enum bcm6362_pinctrl_reg reg;
++ u32 basemode_mask;
++};
++
++struct bcm6362_pinctrl {
++ struct pinctrl_dev *pctldev;
++ struct pinctrl_desc desc;
++
++ void __iomem *led;
++ void __iomem *mode;
++ void __iomem *ctrl;
++ void __iomem *basemode;
++
++ /* register access lock */
++ spinlock_t lock;
++
++ struct gpio_chip gpio[2];
++};
++
++#define BCM6362_PIN(a, b, mask) \
++ { \
++ .number = a, \
++ .name = b, \
++ .drv_data = (void *)(mask), \
++ }
++
++static const struct pinctrl_pin_desc bcm6362_pins[] = {
++ PINCTRL_PIN(0, "gpio0"),
++ PINCTRL_PIN(1, "gpio1"),
++ PINCTRL_PIN(2, "gpio2"),
++ PINCTRL_PIN(3, "gpio3"),
++ PINCTRL_PIN(4, "gpio4"),
++ PINCTRL_PIN(5, "gpio5"),
++ PINCTRL_PIN(6, "gpio6"),
++ PINCTRL_PIN(7, "gpio7"),
++ BCM6362_PIN(8, "gpio8", BASEMODE_NAND),
++ PINCTRL_PIN(9, "gpio9"),
++ PINCTRL_PIN(10, "gpio10"),
++ PINCTRL_PIN(11, "gpio11"),
++ BCM6362_PIN(12, "gpio12", BASEMODE_NAND),
++ BCM6362_PIN(13, "gpio13", BASEMODE_NAND),
++ BCM6362_PIN(14, "gpio14", BASEMODE_NAND),
++ BCM6362_PIN(15, "gpio15", BASEMODE_NAND),
++ BCM6362_PIN(16, "gpio16", BASEMODE_NAND),
++ BCM6362_PIN(17, "gpio17", BASEMODE_NAND),
++ BCM6362_PIN(18, "gpio18", BASEMODE_NAND),
++ BCM6362_PIN(19, "gpio19", BASEMODE_NAND),
++ BCM6362_PIN(20, "gpio20", BASEMODE_NAND),
++ BCM6362_PIN(21, "gpio21", BASEMODE_NAND),
++ BCM6362_PIN(22, "gpio22", BASEMODE_NAND),
++ BCM6362_PIN(23, "gpio23", BASEMODE_NAND),
++ PINCTRL_PIN(24, "gpio24"),
++ PINCTRL_PIN(25, "gpio25"),
++ PINCTRL_PIN(26, "gpio26"),
++ BCM6362_PIN(27, "gpio27", BASEMODE_NAND),
++ PINCTRL_PIN(28, "gpio28"),
++ PINCTRL_PIN(29, "gpio29"),
++ PINCTRL_PIN(30, "gpio30"),
++ PINCTRL_PIN(31, "gpio31"),
++ PINCTRL_PIN(32, "gpio32"),
++ PINCTRL_PIN(33, "gpio33"),
++ PINCTRL_PIN(34, "gpio34"),
++ PINCTRL_PIN(35, "gpio35"),
++ PINCTRL_PIN(36, "gpio36"),
++ PINCTRL_PIN(37, "gpio37"),
++ PINCTRL_PIN(38, "gpio38"),
++ PINCTRL_PIN(39, "gpio39"),
++ PINCTRL_PIN(40, "gpio40"),
++ PINCTRL_PIN(41, "gpio41"),
++ PINCTRL_PIN(42, "gpio42"),
++ PINCTRL_PIN(43, "gpio43"),
++ PINCTRL_PIN(44, "gpio44"),
++ PINCTRL_PIN(45, "gpio45"),
++ PINCTRL_PIN(46, "gpio46"),
++ PINCTRL_PIN(47, "gpio47"),
++};
++
++static unsigned gpio0_pins[] = { 0 };
++static unsigned gpio1_pins[] = { 1 };
++static unsigned gpio2_pins[] = { 2 };
++static unsigned gpio3_pins[] = { 3 };
++static unsigned gpio4_pins[] = { 4 };
++static unsigned gpio5_pins[] = { 5 };
++static unsigned gpio6_pins[] = { 6 };
++static unsigned gpio7_pins[] = { 7 };
++static unsigned gpio8_pins[] = { 8 };
++static unsigned gpio9_pins[] = { 9 };
++static unsigned gpio10_pins[] = { 10 };
++static unsigned gpio11_pins[] = { 11 };
++static unsigned gpio12_pins[] = { 12 };
++static unsigned gpio13_pins[] = { 13 };
++static unsigned gpio14_pins[] = { 14 };
++static unsigned gpio15_pins[] = { 15 };
++static unsigned gpio16_pins[] = { 16 };
++static unsigned gpio17_pins[] = { 17 };
++static unsigned gpio18_pins[] = { 18 };
++static unsigned gpio19_pins[] = { 19 };
++static unsigned gpio20_pins[] = { 20 };
++static unsigned gpio21_pins[] = { 21 };
++static unsigned gpio22_pins[] = { 22 };
++static unsigned gpio23_pins[] = { 23 };
++static unsigned gpio24_pins[] = { 24 };
++static unsigned gpio25_pins[] = { 25 };
++static unsigned gpio26_pins[] = { 26 };
++static unsigned gpio27_pins[] = { 27 };
++static unsigned gpio28_pins[] = { 28 };
++static unsigned gpio29_pins[] = { 29 };
++static unsigned gpio30_pins[] = { 30 };
++static unsigned gpio31_pins[] = { 31 };
++static unsigned gpio32_pins[] = { 32 };
++static unsigned gpio33_pins[] = { 33 };
++static unsigned gpio34_pins[] = { 34 };
++static unsigned gpio35_pins[] = { 35 };
++static unsigned gpio36_pins[] = { 36 };
++static unsigned gpio37_pins[] = { 37 };
++static unsigned gpio38_pins[] = { 38 };
++static unsigned gpio39_pins[] = { 39 };
++static unsigned gpio40_pins[] = { 40 };
++static unsigned gpio41_pins[] = { 41 };
++static unsigned gpio42_pins[] = { 42 };
++static unsigned gpio43_pins[] = { 43 };
++static unsigned gpio44_pins[] = { 44 };
++static unsigned gpio45_pins[] = { 45 };
++static unsigned gpio46_pins[] = { 46 };
++static unsigned gpio47_pins[] = { 47 };
++
++static unsigned nand_grp_pins[] = {
++ 8, 12, 13, 14, 15, 16, 17,
++ 18, 19, 20, 21, 22, 23, 27,
++};
++
++#define BCM6362_GROUP(n) \
++ { \
++ .name = #n, \
++ .pins = n##_pins, \
++ .num_pins = ARRAY_SIZE(n##_pins), \
++ }
++
++static struct bcm6362_pingroup bcm6362_groups[] = {
++ BCM6362_GROUP(gpio0),
++ BCM6362_GROUP(gpio1),
++ BCM6362_GROUP(gpio2),
++ BCM6362_GROUP(gpio3),
++ BCM6362_GROUP(gpio4),
++ BCM6362_GROUP(gpio5),
++ BCM6362_GROUP(gpio6),
++ BCM6362_GROUP(gpio7),
++ BCM6362_GROUP(gpio8),
++ BCM6362_GROUP(gpio9),
++ BCM6362_GROUP(gpio10),
++ BCM6362_GROUP(gpio11),
++ BCM6362_GROUP(gpio12),
++ BCM6362_GROUP(gpio13),
++ BCM6362_GROUP(gpio14),
++ BCM6362_GROUP(gpio15),
++ BCM6362_GROUP(gpio16),
++ BCM6362_GROUP(gpio17),
++ BCM6362_GROUP(gpio18),
++ BCM6362_GROUP(gpio19),
++ BCM6362_GROUP(gpio20),
++ BCM6362_GROUP(gpio21),
++ BCM6362_GROUP(gpio22),
++ BCM6362_GROUP(gpio23),
++ BCM6362_GROUP(gpio24),
++ BCM6362_GROUP(gpio25),
++ BCM6362_GROUP(gpio26),
++ BCM6362_GROUP(gpio27),
++ BCM6362_GROUP(gpio28),
++ BCM6362_GROUP(gpio29),
++ BCM6362_GROUP(gpio30),
++ BCM6362_GROUP(gpio31),
++ BCM6362_GROUP(gpio32),
++ BCM6362_GROUP(gpio33),
++ BCM6362_GROUP(gpio34),
++ BCM6362_GROUP(gpio35),
++ BCM6362_GROUP(gpio36),
++ BCM6362_GROUP(gpio37),
++ BCM6362_GROUP(gpio38),
++ BCM6362_GROUP(gpio39),
++ BCM6362_GROUP(gpio40),
++ BCM6362_GROUP(gpio41),
++ BCM6362_GROUP(gpio42),
++ BCM6362_GROUP(gpio43),
++ BCM6362_GROUP(gpio44),
++ BCM6362_GROUP(gpio45),
++ BCM6362_GROUP(gpio46),
++ BCM6362_GROUP(gpio47),
++ BCM6362_GROUP(nand_grp),
++};
++
++static const char * const led_groups[] = {
++ "gpio0",
++ "gpio1",
++ "gpio2",
++ "gpio3",
++ "gpio4",
++ "gpio5",
++ "gpio6",
++ "gpio7",
++ "gpio8",
++ "gpio9",
++ "gpio10",
++ "gpio11",
++ "gpio12",
++ "gpio13",
++ "gpio14",
++ "gpio15",
++ "gpio16",
++ "gpio17",
++ "gpio18",
++ "gpio19",
++ "gpio20",
++ "gpio21",
++ "gpio22",
++ "gpio23",
++};
++
++static const char * const usb_device_led_groups[] = {
++ "gpio0",
++};
++
++static const char * const sys_irq_groups[] = {
++ "gpio1",
++};
++
++static const char * const serial_led_clk_groups[] = {
++ "gpio2",
++};
++
++static const char * const serial_led_data_groups[] = {
++ "gpio3",
++};
++
++static const char * const robosw_led_data_groups[] = {
++ "gpio4",
++};
++
++static const char * const robosw_led_clk_groups[] = {
++ "gpio5",
++};
++
++static const char * const robosw_led0_groups[] = {
++ "gpio6",
++};
++
++static const char * const robosw_led1_groups[] = {
++ "gpio7",
++};
++
++static const char * const inet_led_groups[] = {
++ "gpio8",
++};
++
++static const char * const spi_cs2_groups[] = {
++ "gpio9",
++};
++
++static const char * const spi_cs3_groups[] = {
++ "gpio10",
++};
++
++static const char * const ntr_pulse_groups[] = {
++ "gpio11",
++};
++
++static const char * const uart1_scts_groups[] = {
++ "gpio12",
++};
++
++static const char * const uart1_srts_groups[] = {
++ "gpio13",
++};
++
++static const char * const uart1_sdin_groups[] = {
++ "gpio14",
++};
++
++static const char * const uart1_sdout_groups[] = {
++ "gpio15",
++};
++
++static const char * const adsl_spi_miso_groups[] = {
++ "gpio16",
++};
++
++static const char * const adsl_spi_mosi_groups[] = {
++ "gpio17",
++};
++
++static const char * const adsl_spi_clk_groups[] = {
++ "gpio18",
++};
++
++static const char * const adsl_spi_cs_groups[] = {
++ "gpio19",
++};
++
++static const char * const ephy0_led_groups[] = {
++ "gpio20",
++};
++
++static const char * const ephy1_led_groups[] = {
++ "gpio21",
++};
++
++static const char * const ephy2_led_groups[] = {
++ "gpio22",
++};
++
++static const char * const ephy3_led_groups[] = {
++ "gpio23",
++};
++
++static const char * const ext_irq0_groups[] = {
++ "gpio24",
++};
++
++static const char * const ext_irq1_groups[] = {
++ "gpio25",
++};
++
++static const char * const ext_irq2_groups[] = {
++ "gpio26",
++};
++
++static const char * const ext_irq3_groups[] = {
++ "gpio27",
++};
++
++static const char * const wifi_groups[] = {
++ "gpio32",
++ "gpio33",
++ "gpio34",
++ "gpio35",
++ "gpio36",
++ "gpio37",
++ "gpio38",
++ "gpio39",
++ "gpio40",
++ "gpio41",
++ "gpio42",
++ "gpio43",
++ "gpio44",
++ "gpio45",
++ "gpio46",
++ "gpio47",
++};
++
++static const char * const nand_groups[] = {
++ "nand_grp",
++};
++
++#define BCM6362_LED_FUN(n) \
++ { \
++ .name = #n, \
++ .groups = n##_groups, \
++ .num_groups = ARRAY_SIZE(n##_groups), \
++ .reg = BCM6362_LEDCTRL, \
++ }
++
++#define BCM6362_MODE_FUN(n) \
++ { \
++ .name = #n, \
++ .groups = n##_groups, \
++ .num_groups = ARRAY_SIZE(n##_groups), \
++ .reg = BCM6362_MODE, \
++ }
++
++#define BCM6362_CTRL_FUN(n) \
++ { \
++ .name = #n, \
++ .groups = n##_groups, \
++ .num_groups = ARRAY_SIZE(n##_groups), \
++ .reg = BCM6362_CTRL, \
++ }
++
++#define BCM6362_BASEMODE_FUN(n, mask) \
++ { \
++ .name = #n, \
++ .groups = n##_groups, \
++ .num_groups = ARRAY_SIZE(n##_groups), \
++ .reg = BCM6362_BASEMODE, \
++ .basemode_mask = (mask), \
++ }
++
++static const struct bcm6362_function bcm6362_funcs[] = {
++ BCM6362_LED_FUN(led),
++ BCM6362_MODE_FUN(usb_device_led),
++ BCM6362_MODE_FUN(sys_irq),
++ BCM6362_MODE_FUN(serial_led_clk),
++ BCM6362_MODE_FUN(serial_led_data),
++ BCM6362_MODE_FUN(robosw_led_data),
++ BCM6362_MODE_FUN(robosw_led_clk),
++ BCM6362_MODE_FUN(robosw_led0),
++ BCM6362_MODE_FUN(robosw_led1),
++ BCM6362_MODE_FUN(inet_led),
++ BCM6362_MODE_FUN(spi_cs2),
++ BCM6362_MODE_FUN(spi_cs3),
++ BCM6362_MODE_FUN(ntr_pulse),
++ BCM6362_MODE_FUN(uart1_scts),
++ BCM6362_MODE_FUN(uart1_srts),
++ BCM6362_MODE_FUN(uart1_sdin),
++ BCM6362_MODE_FUN(uart1_sdout),
++ BCM6362_MODE_FUN(adsl_spi_miso),
++ BCM6362_MODE_FUN(adsl_spi_mosi),
++ BCM6362_MODE_FUN(adsl_spi_clk),
++ BCM6362_MODE_FUN(adsl_spi_cs),
++ BCM6362_MODE_FUN(ephy0_led),
++ BCM6362_MODE_FUN(ephy1_led),
++ BCM6362_MODE_FUN(ephy2_led),
++ BCM6362_MODE_FUN(ephy3_led),
++ BCM6362_MODE_FUN(ext_irq0),
++ BCM6362_MODE_FUN(ext_irq1),
++ BCM6362_MODE_FUN(ext_irq2),
++ BCM6362_MODE_FUN(ext_irq3),
++ BCM6362_CTRL_FUN(wifi),
++ BCM6362_BASEMODE_FUN(nand, BASEMODE_NAND),
++};
++
++static int bcm6362_pinctrl_get_group_count(struct pinctrl_dev *pctldev)
++{
++ return ARRAY_SIZE(bcm6362_groups);
++}
++
++static const char *bcm6362_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
++ unsigned group)
++{
++ return bcm6362_groups[group].name;
++}
++
++static int bcm6362_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
++ unsigned group, const unsigned **pins,
++ unsigned *num_pins)
++{
++ *pins = bcm6362_groups[group].pins;
++ *num_pins = bcm6362_groups[group].num_pins;
++
++ return 0;
++}
++
++static int bcm6362_pinctrl_get_func_count(struct pinctrl_dev *pctldev)
++{
++ return ARRAY_SIZE(bcm6362_funcs);
++}
++
++static const char *bcm6362_pinctrl_get_func_name(struct pinctrl_dev *pctldev,
++ unsigned selector)
++{
++ return bcm6362_funcs[selector].name;
++}
++
++static int bcm6362_pinctrl_get_groups(struct pinctrl_dev *pctldev,
++ unsigned selector,
++ const char * const **groups,
++ unsigned * const num_groups)
++{
++ *groups = bcm6362_funcs[selector].groups;
++ *num_groups = bcm6362_funcs[selector].num_groups;
++
++ return 0;
++}
++
++static void bcm6362_rmw_mux(struct bcm6362_pinctrl *pctl, void __iomem *reg,
++ u32 mask, u32 val)
++{
++ unsigned long flags;
++ u32 tmp;
++
++ spin_lock_irqsave(&pctl->lock, flags);
++ tmp = __raw_readl(reg);
++ tmp &= ~mask;
++ tmp |= val & mask;
++ __raw_writel(tmp, reg);
++
++ spin_unlock_irqrestore(&pctl->lock, flags);
++}
++
++static void bcm6362_set_gpio(struct bcm6362_pinctrl *pctl, unsigned pin)
++{
++ const struct pinctrl_pin_desc *desc = &bcm6362_pins[pin];
++ u32 mask = BIT(pin % 32);
++
++ if (desc->drv_data)
++ bcm6362_rmw_mux(pctl, pctl->basemode, (u32)desc->drv_data, 0);
++
++ if (pin < 32) {
++ /* base mode 0 => gpio 1 => mux function */
++ bcm6362_rmw_mux(pctl, pctl->mode, mask, 0);
++
++ /* pins 0-23 might be muxed to led */
++ if (pin < 24)
++ bcm6362_rmw_mux(pctl, pctl->led, mask, 0);
++ } else {
++ /* ctrl reg 0 => wifi function 1 => gpio */
++ bcm6362_rmw_mux(pctl, pctl->ctrl, mask, mask);
++ }
++}
++
++static int bcm6362_pinctrl_set_mux(struct pinctrl_dev *pctldev,
++ unsigned selector, unsigned group)
++{
++ struct bcm6362_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
++ const struct bcm6362_pingroup *grp = &bcm6362_groups[group];
++ const struct bcm6362_function *f = &bcm6362_funcs[selector];
++ unsigned i;
++ void __iomem *reg;
++ u32 val, mask;
++
++ for (i = 0; i < grp->num_pins; i++)
++ bcm6362_set_gpio(pctl, grp->pins[i]);
++
++ switch (f->reg) {
++ case BCM6362_LEDCTRL:
++ reg = pctl->led;
++ mask = BIT(grp->pins[0]);
++ val = BIT(grp->pins[0]);
++ break;
++ case BCM6362_MODE:
++ reg = pctl->ctrl;
++ mask = BIT(grp->pins[0]);
++ val = BIT(grp->pins[0]);
++ break;
++ case BCM6362_CTRL:
++ reg = pctl->ctrl;
++ mask = BIT(grp->pins[0]);
++ val = 0;
++ break;
++ case BCM6362_BASEMODE:
++ reg = pctl->basemode;
++ mask = f->basemode_mask;
++ val = f->basemode_mask;
++ break;
++ default:
++ WARN_ON(1);
++ return -EINVAL;
++ }
++
++ bcm6362_rmw_mux(pctl, reg, mask, val);
++
++ return 0;
++}
++
++static int bcm6362_gpio_request_enable(struct pinctrl_dev *pctldev,
++ struct pinctrl_gpio_range *range,
++ unsigned offset)
++{
++ struct bcm6362_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
++
++ /* disable all functions using this pin */
++ bcm6362_set_gpio(pctl, offset);
++
++ return 0;
++}
++
++static struct pinctrl_ops bcm6362_pctl_ops = {
++ .get_groups_count = bcm6362_pinctrl_get_group_count,
++ .get_group_name = bcm6362_pinctrl_get_group_name,
++ .get_group_pins = bcm6362_pinctrl_get_group_pins,
++#ifdef CONFIG_OF
++ .dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
++ .dt_free_map = pinctrl_utils_free_map,
++#endif
++};
++
++static struct pinmux_ops bcm6362_pmx_ops = {
++ .get_functions_count = bcm6362_pinctrl_get_func_count,
++ .get_function_name = bcm6362_pinctrl_get_func_name,
++ .get_function_groups = bcm6362_pinctrl_get_groups,
++ .set_mux = bcm6362_pinctrl_set_mux,
++ .gpio_request_enable = bcm6362_gpio_request_enable,
++ .strict = true,
++};
++
++static int bcm6362_pinctrl_probe(struct platform_device *pdev)
++{
++ struct bcm6362_pinctrl *pctl;
++ struct resource *res;
++ void __iomem *led, *mode, *ctrl, *basemode;
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "led");
++ led = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(led))
++ return PTR_ERR(led);
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mode");
++ mode = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(mode))
++ return PTR_ERR(mode);
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ctrl");
++ ctrl = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(ctrl))
++ return PTR_ERR(ctrl);
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "basemode");
++ basemode = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(basemode))
++ return PTR_ERR(basemode);
++
++ pctl = devm_kzalloc(&pdev->dev, sizeof(*pctl), GFP_KERNEL);
++ if (!pctl)
++ return -ENOMEM;
++
++ spin_lock_init(&pctl->lock);
++
++ pctl->led = led;
++ pctl->mode = mode;
++ pctl->ctrl = ctrl;
++ pctl->basemode = basemode;
++
++ pctl->desc.name = dev_name(&pdev->dev);
++ pctl->desc.owner = THIS_MODULE;
++ pctl->desc.pctlops = &bcm6362_pctl_ops;
++ pctl->desc.pmxops = &bcm6362_pmx_ops;
++
++ pctl->desc.npins = ARRAY_SIZE(bcm6362_pins);
++ pctl->desc.pins = bcm6362_pins;
++
++ platform_set_drvdata(pdev, pctl);
++
++ pctl->pctldev = bcm63xx_pinctrl_register(pdev, &pctl->desc, pctl,
++ pctl->gpio, BCM6362_NGPIO);
++ if (IS_ERR(pctl->pctldev))
++ return PTR_ERR(pctl->pctldev);
++
++ return 0;
++}
++
++static const struct of_device_id bcm6362_pinctrl_match[] = {
++ { .compatible = "brcm,bcm6362-pinctrl", },
++ { },
++};
++
++static struct platform_driver bcm6362_pinctrl_driver = {
++ .probe = bcm6362_pinctrl_probe,
++ .driver = {
++ .name = "bcm6362-pinctrl",
++ .of_match_table = bcm6362_pinctrl_match,
++ },
++};
++
++builtin_platform_driver(bcm6362_pinctrl_driver);
--- /dev/null
+From 30594cf9bfff176a9e4b14c50dcd8b9d0cc3edec Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Wed, 27 Jul 2016 11:36:51 +0200
+Subject: [PATCH 10/16] Documentation: add BCM6368 pincontroller binding
+ documentation
+
+Add binding documentation for the pincontrol core found in BCM6368 SoCs.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ .../bindings/pinctrl/brcm,bcm6368-pinctrl.txt | 67 ++++++++++++++++++++++
+ 1 file changed, 67 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/pinctrl/brcm,bcm6368-pinctrl.txt
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6368-pinctrl.txt
+@@ -0,0 +1,67 @@
++* Broadcom BCM6368 pin controller
++
++Required properties:
++- compatible: Must be "brcm,bcm6368-pinctrl".
++- reg: Register specifiers of dirout, dat, mode registers.
++- reg-names: Must be "dirout", "dat", "mode".
++- brcm,gpiobasemode: Phandle to the gpio basemode register.
++- gpio-controller: Identifies this node as a GPIO controller.
++- #gpio-cells: Must be <2>.
++
++Example:
++
++pinctrl: pin-controller@10000080 {
++ compatible = "brcm,bcm6368-pinctrl";
++ reg = <0x10000080 0x08>,
++ <0x10000088 0x08>,
++ <0x10000098 0x04>;
++ reg-names = "dirout", "dat", "mode";
++ brcm,gpiobasemode = <&gpiobasemode>;
++
++ gpio-controller;
++ #gpio-cells = <2>;
++};
++
++gpiobasemode: syscon@100000b8 {
++ compatible = "brcm,bcm6368-gpiobasemode", "syscon";
++ reg = <0x100000b8 4>;
++ native-endian;
++};
++
++Available pins/groups and functions:
++
++name pins functions
++-----------------------------------------------------------
++gpio0 0 analog_afe0
++gpio1 1 analog_afe1
++gpio2 2 sys_irq
++gpio3 3 serial_led_data
++gpio4 4 serial_led_clk
++gpio5 5 inet_led
++gpio6 6 ephy0_led
++gpio7 7 ephy1_led
++gpio8 8 ephy2_led
++gpio9 9 ephy3_led
++gpio10 10 robosw_led_data
++gpio11 11 robosw_led_clk
++gpio12 12 robosw_led0
++gpio13 13 robosw_led1
++gpio14 14 usb_device_led
++gpio15 15 -
++gpio16 16 pci_req1
++gpio17 17 pci_gnt1
++gpio18 18 pci_intb
++gpio19 19 pci_req0
++gpio20 20 pci_gnt0
++gpio21 21 -
++gpio22 22 pcmcia_cd1
++gpio23 23 pcmcia_cd2
++gpio24 24 pcmcia_vs1
++gpio25 25 pcmcia_vs2
++gpio26 26 ebi_cs2
++gpio27 27 ebi_cs3
++gpio28 28 spi_cs2
++gpio29 29 spi_cs3
++gpio30 30 spi_cs4
++gpio31 31 spi_cs5
++uart1_grp 30-33 uart1
--- /dev/null
+From 90be3cb4f1a45b8be4a4ec264cd66c2f8e893fcb Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Fri, 24 Jun 2016 22:18:25 +0200
+Subject: [PATCH 11/16] pinctrl: add a pincontrol driver for BCM6368
+
+Add a pincontrol driver for BCM6368. BCM6368 allows muxing the first 32
+GPIOs onto alternative functions. Not all are documented.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ drivers/pinctrl/bcm63xx/Kconfig | 15 +
+ drivers/pinctrl/bcm63xx/Makefile | 1 +
+ drivers/pinctrl/bcm63xx/pinctrl-bcm6368.c | 573 ++++++++++++++++++++++++++++++
+ 3 files changed, 589 insertions(+)
+ create mode 100644 drivers/pinctrl/bcm63xx/pinctrl-bcm6368.c
+
+--- a/drivers/pinctrl/bcm63xx/Kconfig
++++ b/drivers/pinctrl/bcm63xx/Kconfig
+@@ -30,3 +30,18 @@ config PINCTRL_BCM6362
+ select PINCONF
+ select PINCTRL_BCM63XX
+ select GENERIC_PINCONF
++
++config PINCTRL_BCM6368
++ bool "BCM6368 pincontrol driver" if COMPILE_TEST
++ select PINMUX
++ select PINCONF
++ select PINCTRL_BCM63XX
++ select GENERIC_PINCONF
++ select MFD_SYSCON
++
++config PINCTRL_BCM63268
++ bool "BCM63268 pincontrol driver" if COMPILE_TEST
++ select PINMUX
++ select PINCONF
++ select PINCTRL_BCM63XX
++ select GENERIC_PINCONF
+--- a/drivers/pinctrl/bcm63xx/Makefile
++++ b/drivers/pinctrl/bcm63xx/Makefile
+@@ -3,3 +3,4 @@ obj-$(CONFIG_PINCTRL_BCM6328) += pinctrl
+ obj-$(CONFIG_PINCTRL_BCM6348) += pinctrl-bcm6348.o
+ obj-$(CONFIG_PINCTRL_BCM6358) += pinctrl-bcm6358.o
+ obj-$(CONFIG_PINCTRL_BCM6362) += pinctrl-bcm6362.o
++obj-$(CONFIG_PINCTRL_BCM6368) += pinctrl-bcm6368.o
+--- /dev/null
++++ b/drivers/pinctrl/bcm63xx/pinctrl-bcm6368.c
+@@ -0,0 +1,573 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License. See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2016 Jonas Gorski <jonas.gorski@gmail.com>
++ */
++
++#include <linux/bitops.h>
++#include <linux/kernel.h>
++#include <linux/gpio.h>
++#include <linux/mfd/syscon.h>
++#include <linux/of.h>
++#include <linux/of_address.h>
++#include <linux/of_gpio.h>
++#include <linux/pinctrl/pinconf.h>
++#include <linux/pinctrl/pinconf-generic.h>
++#include <linux/pinctrl/pinmux.h>
++#include <linux/pinctrl/machine.h>
++#include <linux/platform_device.h>
++#include <linux/regmap.h>
++#include <linux/slab.h>
++#include <linux/spinlock.h>
++
++#include "../core.h"
++#include "../pinctrl-utils.h"
++
++#include "pinctrl-bcm63xx.h"
++
++#define BCM6368_NGPIO 38
++
++#define BCM6368_BASEMODE_MASK 0x7
++#define BCM6368_BASEMODE_GPIO 0x0
++#define BCM6368_BASEMODE_UART1 0x1
++
++struct bcm6368_pingroup {
++ const char *name;
++ const unsigned * const pins;
++ const unsigned num_pins;
++};
++
++struct bcm6368_function {
++ const char *name;
++ const char * const *groups;
++ const unsigned num_groups;
++
++ unsigned dir_out:16;
++ unsigned basemode:3;
++};
++
++struct bcm6368_pinctrl {
++ struct pinctrl_dev *pctldev;
++ struct pinctrl_desc desc;
++
++ void __iomem *mode;
++ struct regmap_field *overlay;
++
++ /* register access lock */
++ spinlock_t lock;
++
++ struct gpio_chip gpio[2];
++};
++
++#define BCM6368_BASEMODE_PIN(a, b) \
++ { \
++ .number = a, \
++ .name = b, \
++ .drv_data = (void *)true \
++ }
++
++static const struct pinctrl_pin_desc bcm6368_pins[] = {
++ PINCTRL_PIN(0, "gpio0"),
++ PINCTRL_PIN(1, "gpio1"),
++ PINCTRL_PIN(2, "gpio2"),
++ PINCTRL_PIN(3, "gpio3"),
++ PINCTRL_PIN(4, "gpio4"),
++ PINCTRL_PIN(5, "gpio5"),
++ PINCTRL_PIN(6, "gpio6"),
++ PINCTRL_PIN(7, "gpio7"),
++ PINCTRL_PIN(8, "gpio8"),
++ PINCTRL_PIN(9, "gpio9"),
++ PINCTRL_PIN(10, "gpio10"),
++ PINCTRL_PIN(11, "gpio11"),
++ PINCTRL_PIN(12, "gpio12"),
++ PINCTRL_PIN(13, "gpio13"),
++ PINCTRL_PIN(14, "gpio14"),
++ PINCTRL_PIN(15, "gpio15"),
++ PINCTRL_PIN(16, "gpio16"),
++ PINCTRL_PIN(17, "gpio17"),
++ PINCTRL_PIN(18, "gpio18"),
++ PINCTRL_PIN(19, "gpio19"),
++ PINCTRL_PIN(20, "gpio20"),
++ PINCTRL_PIN(21, "gpio21"),
++ PINCTRL_PIN(22, "gpio22"),
++ PINCTRL_PIN(23, "gpio23"),
++ PINCTRL_PIN(24, "gpio24"),
++ PINCTRL_PIN(25, "gpio25"),
++ PINCTRL_PIN(26, "gpio26"),
++ PINCTRL_PIN(27, "gpio27"),
++ PINCTRL_PIN(28, "gpio28"),
++ PINCTRL_PIN(29, "gpio29"),
++ BCM6368_BASEMODE_PIN(30, "gpio30"),
++ BCM6368_BASEMODE_PIN(31, "gpio31"),
++ BCM6368_BASEMODE_PIN(32, "gpio32"),
++ BCM6368_BASEMODE_PIN(33, "gpio33"),
++ PINCTRL_PIN(34, "gpio34"),
++ PINCTRL_PIN(35, "gpio35"),
++ PINCTRL_PIN(36, "gpio36"),
++ PINCTRL_PIN(37, "gpio37"),
++};
++
++static unsigned gpio0_pins[] = { 0 };
++static unsigned gpio1_pins[] = { 1 };
++static unsigned gpio2_pins[] = { 2 };
++static unsigned gpio3_pins[] = { 3 };
++static unsigned gpio4_pins[] = { 4 };
++static unsigned gpio5_pins[] = { 5 };
++static unsigned gpio6_pins[] = { 6 };
++static unsigned gpio7_pins[] = { 7 };
++static unsigned gpio8_pins[] = { 8 };
++static unsigned gpio9_pins[] = { 9 };
++static unsigned gpio10_pins[] = { 10 };
++static unsigned gpio11_pins[] = { 11 };
++static unsigned gpio12_pins[] = { 12 };
++static unsigned gpio13_pins[] = { 13 };
++static unsigned gpio14_pins[] = { 14 };
++static unsigned gpio15_pins[] = { 15 };
++static unsigned gpio16_pins[] = { 16 };
++static unsigned gpio17_pins[] = { 17 };
++static unsigned gpio18_pins[] = { 18 };
++static unsigned gpio19_pins[] = { 19 };
++static unsigned gpio20_pins[] = { 20 };
++static unsigned gpio21_pins[] = { 21 };
++static unsigned gpio22_pins[] = { 22 };
++static unsigned gpio23_pins[] = { 23 };
++static unsigned gpio24_pins[] = { 24 };
++static unsigned gpio25_pins[] = { 25 };
++static unsigned gpio26_pins[] = { 26 };
++static unsigned gpio27_pins[] = { 27 };
++static unsigned gpio28_pins[] = { 28 };
++static unsigned gpio29_pins[] = { 29 };
++static unsigned gpio30_pins[] = { 30 };
++static unsigned gpio31_pins[] = { 31 };
++static unsigned uart1_grp_pins[] = { 30, 31, 32, 33 };
++
++#define BCM6368_GROUP(n) \
++ { \
++ .name = #n, \
++ .pins = n##_pins, \
++ .num_pins = ARRAY_SIZE(n##_pins), \
++ }
++
++static struct bcm6368_pingroup bcm6368_groups[] = {
++ BCM6368_GROUP(gpio0),
++ BCM6368_GROUP(gpio1),
++ BCM6368_GROUP(gpio2),
++ BCM6368_GROUP(gpio3),
++ BCM6368_GROUP(gpio4),
++ BCM6368_GROUP(gpio5),
++ BCM6368_GROUP(gpio6),
++ BCM6368_GROUP(gpio7),
++ BCM6368_GROUP(gpio8),
++ BCM6368_GROUP(gpio9),
++ BCM6368_GROUP(gpio10),
++ BCM6368_GROUP(gpio11),
++ BCM6368_GROUP(gpio12),
++ BCM6368_GROUP(gpio13),
++ BCM6368_GROUP(gpio14),
++ BCM6368_GROUP(gpio15),
++ BCM6368_GROUP(gpio16),
++ BCM6368_GROUP(gpio17),
++ BCM6368_GROUP(gpio18),
++ BCM6368_GROUP(gpio19),
++ BCM6368_GROUP(gpio20),
++ BCM6368_GROUP(gpio21),
++ BCM6368_GROUP(gpio22),
++ BCM6368_GROUP(gpio23),
++ BCM6368_GROUP(gpio24),
++ BCM6368_GROUP(gpio25),
++ BCM6368_GROUP(gpio26),
++ BCM6368_GROUP(gpio27),
++ BCM6368_GROUP(gpio28),
++ BCM6368_GROUP(gpio29),
++ BCM6368_GROUP(gpio30),
++ BCM6368_GROUP(gpio31),
++ BCM6368_GROUP(uart1_grp),
++};
++
++static const char * const analog_afe_0_groups[] = {
++ "gpio0",
++};
++
++static const char * const analog_afe_1_groups[] = {
++ "gpio1",
++};
++
++static const char * const sys_irq_groups[] = {
++ "gpio2",
++};
++
++static const char * const serial_led_data_groups[] = {
++ "gpio3",
++};
++
++static const char * const serial_led_clk_groups[] = {
++ "gpio4",
++};
++
++static const char * const inet_led_groups[] = {
++ "gpio5",
++};
++
++static const char * const ephy0_led_groups[] = {
++ "gpio6",
++};
++
++static const char * const ephy1_led_groups[] = {
++ "gpio7",
++};
++
++static const char * const ephy2_led_groups[] = {
++ "gpio8",
++};
++
++static const char * const ephy3_led_groups[] = {
++ "gpio9",
++};
++
++static const char * const robosw_led_data_groups[] = {
++ "gpio10",
++};
++
++static const char * const robosw_led_clk_groups[] = {
++ "gpio11",
++};
++
++static const char * const robosw_led0_groups[] = {
++ "gpio12",
++};
++
++static const char * const robosw_led1_groups[] = {
++ "gpio13",
++};
++
++static const char * const usb_device_led_groups[] = {
++ "gpio14",
++};
++
++static const char * const pci_req1_groups[] = {
++ "gpio16",
++};
++
++static const char * const pci_gnt1_groups[] = {
++ "gpio17",
++};
++
++static const char * const pci_intb_groups[] = {
++ "gpio18",
++};
++
++static const char * const pci_req0_groups[] = {
++ "gpio19",
++};
++
++static const char * const pci_gnt0_groups[] = {
++ "gpio20",
++};
++
++static const char * const pcmcia_cd1_groups[] = {
++ "gpio22",
++};
++
++static const char * const pcmcia_cd2_groups[] = {
++ "gpio23",
++};
++
++static const char * const pcmcia_vs1_groups[] = {
++ "gpio24",
++};
++
++static const char * const pcmcia_vs2_groups[] = {
++ "gpio25",
++};
++
++static const char * const ebi_cs2_groups[] = {
++ "gpio26",
++};
++
++static const char * const ebi_cs3_groups[] = {
++ "gpio27",
++};
++
++static const char * const spi_cs2_groups[] = {
++ "gpio28",
++};
++
++static const char * const spi_cs3_groups[] = {
++ "gpio29",
++};
++
++static const char * const spi_cs4_groups[] = {
++ "gpio30",
++};
++
++static const char * const spi_cs5_groups[] = {
++ "gpio31",
++};
++
++static const char * const uart1_groups[] = {
++ "uart1_grp",
++};
++
++#define BCM6368_FUN(n, out) \
++ { \
++ .name = #n, \
++ .groups = n##_groups, \
++ .num_groups = ARRAY_SIZE(n##_groups), \
++ .dir_out = out, \
++ }
++
++#define BCM6368_BASEMODE_FUN(n, val, out) \
++ { \
++ .name = #n, \
++ .groups = n##_groups, \
++ .num_groups = ARRAY_SIZE(n##_groups), \
++ .basemode = BCM6368_BASEMODE_##val, \
++ .dir_out = out, \
++ }
++
++static const struct bcm6368_function bcm6368_funcs[] = {
++ BCM6368_FUN(analog_afe_0, 1),
++ BCM6368_FUN(analog_afe_1, 1),
++ BCM6368_FUN(sys_irq, 1),
++ BCM6368_FUN(serial_led_data, 1),
++ BCM6368_FUN(serial_led_clk, 1),
++ BCM6368_FUN(inet_led, 1),
++ BCM6368_FUN(ephy0_led, 1),
++ BCM6368_FUN(ephy1_led, 1),
++ BCM6368_FUN(ephy2_led, 1),
++ BCM6368_FUN(ephy3_led, 1),
++ BCM6368_FUN(robosw_led_data, 1),
++ BCM6368_FUN(robosw_led_clk, 1),
++ BCM6368_FUN(robosw_led0, 1),
++ BCM6368_FUN(robosw_led1, 1),
++ BCM6368_FUN(usb_device_led, 1),
++ BCM6368_FUN(pci_req1, 0),
++ BCM6368_FUN(pci_gnt1, 0),
++ BCM6368_FUN(pci_intb, 0),
++ BCM6368_FUN(pci_req0, 0),
++ BCM6368_FUN(pci_gnt0, 0),
++ BCM6368_FUN(pcmcia_cd1, 0),
++ BCM6368_FUN(pcmcia_cd2, 0),
++ BCM6368_FUN(pcmcia_vs1, 0),
++ BCM6368_FUN(pcmcia_vs2, 0),
++ BCM6368_FUN(ebi_cs2, 1),
++ BCM6368_FUN(ebi_cs3, 1),
++ BCM6368_FUN(spi_cs2, 1),
++ BCM6368_FUN(spi_cs3, 1),
++ BCM6368_FUN(spi_cs4, 1),
++ BCM6368_FUN(spi_cs5, 1),
++ BCM6368_BASEMODE_FUN(uart1, UART1, 0x6),
++};
++
++static int bcm6368_pinctrl_get_group_count(struct pinctrl_dev *pctldev)
++{
++ return ARRAY_SIZE(bcm6368_groups);
++}
++
++static const char *bcm6368_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
++ unsigned group)
++{
++ return bcm6368_groups[group].name;
++}
++
++static int bcm6368_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
++ unsigned group, const unsigned **pins,
++ unsigned *num_pins)
++{
++ *pins = bcm6368_groups[group].pins;
++ *num_pins = bcm6368_groups[group].num_pins;
++
++ return 0;
++}
++
++static int bcm6368_pinctrl_get_func_count(struct pinctrl_dev *pctldev)
++{
++ return ARRAY_SIZE(bcm6368_funcs);
++}
++
++static const char *bcm6368_pinctrl_get_func_name(struct pinctrl_dev *pctldev,
++ unsigned selector)
++{
++ return bcm6368_funcs[selector].name;
++}
++
++static int bcm6368_pinctrl_get_groups(struct pinctrl_dev *pctldev,
++ unsigned selector,
++ const char * const **groups,
++ unsigned * const num_groups)
++{
++ *groups = bcm6368_funcs[selector].groups;
++ *num_groups = bcm6368_funcs[selector].num_groups;
++
++ return 0;
++}
++
++static void bcm6368_rmw_mux(struct bcm6368_pinctrl *pctl, void __iomem *reg,
++ u32 mask, u32 val)
++{
++ u32 tmp;
++
++ tmp = __raw_readl(reg);
++ tmp &= ~mask;
++ tmp |= (val & mask);
++ __raw_writel(tmp, reg);
++}
++
++static int bcm6368_pinctrl_set_mux(struct pinctrl_dev *pctldev,
++ unsigned selector, unsigned group)
++{
++ struct bcm6368_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
++ const struct bcm6368_pingroup *grp = &bcm6368_groups[group];
++ const struct bcm6368_function *fun = &bcm6368_funcs[selector];
++ unsigned long flags;
++ int i, pin;
++
++ spin_lock_irqsave(&pctl->lock, flags);
++ if (fun->basemode) {
++ u32 mask = 0;
++
++ for (i = 0; i < grp->num_pins; i++) {
++ pin = grp->pins[i];
++ if (pin < 32)
++ mask |= BIT(pin);
++ }
++
++ bcm6368_rmw_mux(pctl, pctl->mode, mask, 0);
++ regmap_field_write(pctl->overlay, fun->basemode);
++ } else {
++ pin = grp->pins[0];
++
++ if (bcm6368_pins[pin].drv_data)
++ regmap_field_write(pctl->overlay,
++ BCM6368_BASEMODE_GPIO);
++
++ bcm6368_rmw_mux(pctl, pctl->mode, BIT(pin), BIT(pin));
++ }
++ spin_unlock_irqrestore(&pctl->lock, flags);
++
++ for (pin = 0; pin < grp->num_pins; pin++) {
++ int hw_gpio = bcm6368_pins[pin].number;
++ struct gpio_chip *gc = &pctl->gpio[hw_gpio / 32];
++
++ if (fun->dir_out & BIT(pin))
++ gc->direction_output(gc, hw_gpio % 32, 0);
++ else
++ gc->direction_input(gc, hw_gpio % 32);
++ }
++
++ return 0;
++}
++
++static int bcm6368_gpio_request_enable(struct pinctrl_dev *pctldev,
++ struct pinctrl_gpio_range *range,
++ unsigned offset)
++{
++ struct bcm6368_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
++ unsigned long flags;
++
++ if (offset >= 32 && !bcm6368_pins[offset].drv_data)
++ return 0;
++
++ spin_lock_irqsave(&pctl->lock, flags);
++ /* disable all functions using this pin */
++ if (offset < 32)
++ bcm6368_rmw_mux(pctl, pctl->mode, BIT(offset), 0);
++
++ if (bcm6368_pins[offset].drv_data)
++ regmap_field_write(pctl->overlay, BCM6368_BASEMODE_GPIO);
++
++ spin_unlock_irqrestore(&pctl->lock, flags);
++
++ return 0;
++}
++
++static struct pinctrl_ops bcm6368_pctl_ops = {
++ .get_groups_count = bcm6368_pinctrl_get_group_count,
++ .get_group_name = bcm6368_pinctrl_get_group_name,
++ .get_group_pins = bcm6368_pinctrl_get_group_pins,
++#ifdef CONFIG_OF
++ .dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
++ .dt_free_map = pinctrl_utils_free_map,
++#endif
++};
++
++static struct pinmux_ops bcm6368_pmx_ops = {
++ .get_functions_count = bcm6368_pinctrl_get_func_count,
++ .get_function_name = bcm6368_pinctrl_get_func_name,
++ .get_function_groups = bcm6368_pinctrl_get_groups,
++ .set_mux = bcm6368_pinctrl_set_mux,
++ .gpio_request_enable = bcm6368_gpio_request_enable,
++ .strict = true,
++};
++
++static int bcm6368_pinctrl_probe(struct platform_device *pdev)
++{
++ struct bcm6368_pinctrl *pctl;
++ struct resource *res;
++ void __iomem *mode;
++ struct regmap *basemode;
++ struct reg_field overlay = REG_FIELD(0, 0, 3);
++
++ if (pdev->dev.of_node)
++ basemode = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
++ "brcm,gpiobasemode");
++ else
++ basemode = syscon_regmap_lookup_by_pdevname("syscon.b00000b8");
++
++ if (IS_ERR(basemode))
++ return PTR_ERR(basemode);
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mode");
++ mode = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(mode))
++ return PTR_ERR(mode);
++
++ pctl = devm_kzalloc(&pdev->dev, sizeof(*pctl), GFP_KERNEL);
++ if (!pctl)
++ return -ENOMEM;
++
++ pctl->overlay = devm_regmap_field_alloc(&pdev->dev, mode, overlay);
++ if (IS_ERR(pctl->overlay))
++ return PTR_ERR(pctl->overlay);
++
++ spin_lock_init(&pctl->lock);
++
++ pctl->mode = mode;
++
++ /* disable all muxes by default */
++ __raw_writel(0, pctl->mode);
++
++ pctl->desc.name = dev_name(&pdev->dev);
++ pctl->desc.owner = THIS_MODULE;
++ pctl->desc.pctlops = &bcm6368_pctl_ops;
++ pctl->desc.pmxops = &bcm6368_pmx_ops;
++
++ pctl->desc.npins = ARRAY_SIZE(bcm6368_pins);
++ pctl->desc.pins = bcm6368_pins;
++
++ platform_set_drvdata(pdev, pctl);
++
++ pctl->pctldev = bcm63xx_pinctrl_register(pdev, &pctl->desc, pctl,
++ pctl->gpio, BCM6368_NGPIO);
++ if (IS_ERR(pctl->pctldev))
++ return PTR_ERR(pctl->pctldev);
++
++ return 0;
++}
++
++static const struct of_device_id bcm6368_pinctrl_match[] = {
++ { .compatible = "brcm,bcm6368-pinctrl", },
++ { },
++};
++
++static struct platform_driver bcm6368_pinctrl_driver = {
++ .probe = bcm6368_pinctrl_probe,
++ .driver = {
++ .name = "bcm6368-pinctrl",
++ .of_match_table = bcm6368_pinctrl_match,
++ },
++};
++
++builtin_platform_driver(bcm6368_pinctrl_driver);
--- /dev/null
+From 28cc80e4ada5d73d5305fd268297825cd8d01936 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Wed, 27 Jul 2016 11:37:08 +0200
+Subject: [PATCH 12/16] Documentation: add BCM63268 pincontroller binding
+ documentation
+
+Add binding documentation for the pincontrol core found in the BCM63268
+family SoCs.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ .../bindings/pinctrl/brcm,bcm63268-pinctrl.txt | 88 ++++++++++++++++++++++
+ 1 file changed, 88 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/pinctrl/brcm,bcm63268-pinctrl.txt
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm63268-pinctrl.txt
+@@ -0,0 +1,88 @@
++* Broadcom BCM63268 pin controller
++
++Required properties:
++- compatible: Must be "brcm,bcm6362-pinctrl".
++- reg: Register specifiers of dirout, dat, led, mode, ctrl, basemode registers.
++- reg-names: Must be "dirout", "dat", "led", "mode", "ctrl", "basemode".
++- gpio-controller: Identifies this node as a GPIO controller.
++- #gpio-cells: Must be <2>.
++
++Example:
++
++pinctrl: pin-controller@100000c0 {
++ compatible = "brcm,bcm63268-pinctrl";
++ reg = <0x100000c0 0x8>,
++ <0x100000c8 0x8>,
++ <0x100000d0 0x4>,
++ <0x100000d8 0x4>,
++ <0x100000dc 0x4>,
++ <0x100000f8 0x4>;
++ reg-names = "dirout", "dat", "led", "mode",
++ "ctrl", "basemode";
++
++ gpio-controller;
++ #gpio-cells = <2>;
++};
++
++Available pins/groups and functions:
++
++name pins functions
++-----------------------------------------------------------
++gpio0 0 led, serial_led_clk
++gpio1 1 led, serial_led_data
++gpio2 2 led,
++gpio3 3 led,
++gpio4 4 led,
++gpio5 5 led,
++gpio6 6 led,
++gpio7 7 led,
++gpio8 8 led, hsspi_cs6
++gpio9 9 led, hsspi_cs7
++gpio10 10 led, uart1_scts
++gpio11 11 led, uart1_srts
++gpio12 12 led, uart1_sdin
++gpio13 13 led, uart1_sdout
++gpio14 14 led, ntr_pulse_in
++gpio15 15 led, dsl_ntr_pulse_out
++gpio16 16 led, hsspi_cs4
++gpio17 17 led, hsspi_cs5
++gpio18 18 led, adsl_spi_miso
++gpio19 19 led, adsl_spi_mosi
++gpio20 20 led,
++gpio21 21 led,
++gpio22 22 led, vreg_clk
++gpio23 23 led, pcie_clkreq_b
++gpio24 24 uart1_scts
++gpio25 25 uart1_srts
++gpio26 26 uart1_sdin
++gpio27 27 uart1_sdout
++gpio28 28 ntr_pulse_in
++gpio29 29 dsl_ntr_pulse_out
++gpio30 30 switch_led_clk
++gpio31 31 switch_led_data
++gpio32 32 wifi
++gpio33 33 wifi
++gpio34 34 wifi
++gpio35 35 wifi
++gpio36 36 wifi
++gpio37 37 wifi
++gpio38 38 wifi
++gpio39 39 wifi
++gpio40 40 wifi
++gpio41 41 wifi
++gpio42 42 wifi
++gpio43 43 wifi
++gpio44 44 wifi
++gpio45 45 wifi
++gpio46 46 wifi
++gpio47 47 wifi
++gpio48 48 wifi
++gpio49 49 wifi
++gpio50 50 wifi
++gpio51 51 wifi
++nand_grp 2-7,24-31 nand
++dect_pd_grp 8-9 dect_pd
++vdsl_phy0_grp 10-11 vdsl_phy0
++vdsl_phy1_grp 12-13 vdsl_phy1
++vdsl_phy2_grp 24-25 vdsl_phy2
++vdsl_phy3_grp 26-27 vdsl_phy3
--- /dev/null
+From 8665d3ea63649cc155286c75f83f694a930580e5 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Fri, 24 Jun 2016 22:19:12 +0200
+Subject: [PATCH 13/16] pinctrl: add a pincontrol driver for BCM63268
+
+Add a pincontrol driver for BCM63268. BCM63268 allows muxing GPIOs
+to different functions. Depending on the mux, these are either single
+pin configurations or whole pin groups.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ drivers/pinctrl/bcm63xx/Makefile | 1 +
+ drivers/pinctrl/bcm63xx/pinctrl-bcm63268.c | 710 +++++++++++++++++++++++++++++
+ 2 files changed, 711 insertions(+)
+ create mode 100644 drivers/pinctrl/bcm63xx/pinctrl-bcm63268.c
+
+--- a/drivers/pinctrl/bcm63xx/Makefile
++++ b/drivers/pinctrl/bcm63xx/Makefile
+@@ -4,3 +4,4 @@ obj-$(CONFIG_PINCTRL_BCM6348) += pinctrl
+ obj-$(CONFIG_PINCTRL_BCM6358) += pinctrl-bcm6358.o
+ obj-$(CONFIG_PINCTRL_BCM6362) += pinctrl-bcm6362.o
+ obj-$(CONFIG_PINCTRL_BCM6368) += pinctrl-bcm6368.o
++obj-$(CONFIG_PINCTRL_BCM63268) += pinctrl-bcm63268.o
+--- /dev/null
++++ b/drivers/pinctrl/bcm63xx/pinctrl-bcm63268.c
+@@ -0,0 +1,710 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License. See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2016 Jonas Gorski <jonas.gorski@gmail.com>
++ */
++
++#include <linux/kernel.h>
++#include <linux/spinlock.h>
++#include <linux/bitops.h>
++#include <linux/gpio.h>
++#include <linux/of.h>
++#include <linux/of_gpio.h>
++#include <linux/slab.h>
++#include <linux/platform_device.h>
++
++#include <linux/pinctrl/pinconf.h>
++#include <linux/pinctrl/pinconf-generic.h>
++#include <linux/pinctrl/pinmux.h>
++#include <linux/pinctrl/machine.h>
++
++#include "../core.h"
++#include "../pinctrl-utils.h"
++
++#include "pinctrl-bcm63xx.h"
++
++#define BCM63268_NGPIO 52
++
++/* GPIO_BASEMODE register */
++#define BASEMODE_NAND BIT(2) /* GPIOs 2-7, 24-31 */
++#define BASEMODE_GPIO35 BIT(4) /* GPIO 35 */
++#define BASEMODE_DECTPD BIT(5) /* GPIOs 8/9 */
++#define BASEMODE_VDSL_PHY_0 BIT(6) /* GPIOs 10/11 */
++#define BASEMODE_VDSL_PHY_1 BIT(7) /* GPIOs 12/13 */
++#define BASEMODE_VDSL_PHY_2 BIT(8) /* GPIOs 24/25 */
++#define BASEMODE_VDSL_PHY_3 BIT(9) /* GPIOs 26/27 */
++
++enum bcm63268_pinctrl_reg {
++ BCM63268_LEDCTRL,
++ BCM63268_MODE,
++ BCM63268_CTRL,
++ BCM63268_BASEMODE,
++};
++
++struct bcm63268_pingroup {
++ const char *name;
++ const unsigned * const pins;
++ const unsigned num_pins;
++};
++
++struct bcm63268_function {
++ const char *name;
++ const char * const *groups;
++ const unsigned num_groups;
++
++ enum bcm63268_pinctrl_reg reg;
++ u32 mask;
++};
++
++struct bcm63268_pinctrl {
++ struct pinctrl_dev *pctldev;
++ struct pinctrl_desc desc;
++
++ void __iomem *led;
++ void __iomem *mode;
++ void __iomem *ctrl;
++ void __iomem *basemode;
++
++ /* register access lock */
++ spinlock_t lock;
++
++ struct gpio_chip gpio[2];
++};
++
++#define BCM63268_PIN(a, b, basemode) \
++ { \
++ .number = a, \
++ .name = b, \
++ .drv_data = (void *)(basemode) \
++ }
++
++static const struct pinctrl_pin_desc bcm63268_pins[] = {
++ PINCTRL_PIN(0, "gpio0"),
++ PINCTRL_PIN(1, "gpio1"),
++ BCM63268_PIN(2, "gpio2", BASEMODE_NAND),
++ BCM63268_PIN(3, "gpio3", BASEMODE_NAND),
++ BCM63268_PIN(4, "gpio4", BASEMODE_NAND),
++ BCM63268_PIN(5, "gpio5", BASEMODE_NAND),
++ BCM63268_PIN(6, "gpio6", BASEMODE_NAND),
++ BCM63268_PIN(7, "gpio7", BASEMODE_NAND),
++ BCM63268_PIN(8, "gpio8", BASEMODE_DECTPD),
++ BCM63268_PIN(9, "gpio9", BASEMODE_DECTPD),
++ BCM63268_PIN(10, "gpio10", BASEMODE_VDSL_PHY_0),
++ BCM63268_PIN(11, "gpio11", BASEMODE_VDSL_PHY_0),
++ BCM63268_PIN(12, "gpio12", BASEMODE_VDSL_PHY_1),
++ BCM63268_PIN(13, "gpio13", BASEMODE_VDSL_PHY_1),
++ PINCTRL_PIN(14, "gpio14"),
++ PINCTRL_PIN(15, "gpio15"),
++ PINCTRL_PIN(16, "gpio16"),
++ PINCTRL_PIN(17, "gpio17"),
++ PINCTRL_PIN(18, "gpio18"),
++ PINCTRL_PIN(19, "gpio19"),
++ PINCTRL_PIN(20, "gpio20"),
++ PINCTRL_PIN(21, "gpio21"),
++ PINCTRL_PIN(22, "gpio22"),
++ PINCTRL_PIN(23, "gpio23"),
++ BCM63268_PIN(24, "gpio24", BASEMODE_NAND | BASEMODE_VDSL_PHY_2),
++ BCM63268_PIN(25, "gpio25", BASEMODE_NAND | BASEMODE_VDSL_PHY_2),
++ BCM63268_PIN(26, "gpio26", BASEMODE_NAND | BASEMODE_VDSL_PHY_3),
++ BCM63268_PIN(27, "gpio27", BASEMODE_NAND | BASEMODE_VDSL_PHY_3),
++ BCM63268_PIN(28, "gpio28", BASEMODE_NAND),
++ BCM63268_PIN(29, "gpio29", BASEMODE_NAND),
++ BCM63268_PIN(30, "gpio30", BASEMODE_NAND),
++ BCM63268_PIN(31, "gpio31", BASEMODE_NAND),
++ PINCTRL_PIN(32, "gpio32"),
++ PINCTRL_PIN(33, "gpio33"),
++ PINCTRL_PIN(34, "gpio34"),
++ PINCTRL_PIN(35, "gpio35"),
++ PINCTRL_PIN(36, "gpio36"),
++ PINCTRL_PIN(37, "gpio37"),
++ PINCTRL_PIN(38, "gpio38"),
++ PINCTRL_PIN(39, "gpio39"),
++ PINCTRL_PIN(40, "gpio40"),
++ PINCTRL_PIN(41, "gpio41"),
++ PINCTRL_PIN(42, "gpio42"),
++ PINCTRL_PIN(43, "gpio43"),
++ PINCTRL_PIN(44, "gpio44"),
++ PINCTRL_PIN(45, "gpio45"),
++ PINCTRL_PIN(46, "gpio46"),
++ PINCTRL_PIN(47, "gpio47"),
++ PINCTRL_PIN(48, "gpio48"),
++ PINCTRL_PIN(49, "gpio49"),
++ PINCTRL_PIN(50, "gpio50"),
++ PINCTRL_PIN(51, "gpio51"),
++};
++
++static unsigned gpio0_pins[] = { 0 };
++static unsigned gpio1_pins[] = { 1 };
++static unsigned gpio2_pins[] = { 2 };
++static unsigned gpio3_pins[] = { 3 };
++static unsigned gpio4_pins[] = { 4 };
++static unsigned gpio5_pins[] = { 5 };
++static unsigned gpio6_pins[] = { 6 };
++static unsigned gpio7_pins[] = { 7 };
++static unsigned gpio8_pins[] = { 8 };
++static unsigned gpio9_pins[] = { 9 };
++static unsigned gpio10_pins[] = { 10 };
++static unsigned gpio11_pins[] = { 11 };
++static unsigned gpio12_pins[] = { 12 };
++static unsigned gpio13_pins[] = { 13 };
++static unsigned gpio14_pins[] = { 14 };
++static unsigned gpio15_pins[] = { 15 };
++static unsigned gpio16_pins[] = { 16 };
++static unsigned gpio17_pins[] = { 17 };
++static unsigned gpio18_pins[] = { 18 };
++static unsigned gpio19_pins[] = { 19 };
++static unsigned gpio20_pins[] = { 20 };
++static unsigned gpio21_pins[] = { 21 };
++static unsigned gpio22_pins[] = { 22 };
++static unsigned gpio23_pins[] = { 23 };
++static unsigned gpio24_pins[] = { 24 };
++static unsigned gpio25_pins[] = { 25 };
++static unsigned gpio26_pins[] = { 26 };
++static unsigned gpio27_pins[] = { 27 };
++static unsigned gpio28_pins[] = { 28 };
++static unsigned gpio29_pins[] = { 29 };
++static unsigned gpio30_pins[] = { 30 };
++static unsigned gpio31_pins[] = { 31 };
++static unsigned gpio32_pins[] = { 32 };
++static unsigned gpio33_pins[] = { 33 };
++static unsigned gpio34_pins[] = { 34 };
++static unsigned gpio35_pins[] = { 35 };
++static unsigned gpio36_pins[] = { 36 };
++static unsigned gpio37_pins[] = { 37 };
++static unsigned gpio38_pins[] = { 38 };
++static unsigned gpio39_pins[] = { 39 };
++static unsigned gpio40_pins[] = { 40 };
++static unsigned gpio41_pins[] = { 41 };
++static unsigned gpio42_pins[] = { 42 };
++static unsigned gpio43_pins[] = { 43 };
++static unsigned gpio44_pins[] = { 44 };
++static unsigned gpio45_pins[] = { 45 };
++static unsigned gpio46_pins[] = { 46 };
++static unsigned gpio47_pins[] = { 47 };
++static unsigned gpio48_pins[] = { 48 };
++static unsigned gpio49_pins[] = { 49 };
++static unsigned gpio50_pins[] = { 50 };
++static unsigned gpio51_pins[] = { 51 };
++
++static unsigned nand_grp_pins[] = {
++ 2, 3, 4, 5, 6, 7, 24,
++ 25, 26, 27, 28, 29, 30, 31,
++};
++
++static unsigned dectpd_grp_pins[] = { 8, 9 };
++static unsigned vdsl_phy0_grp_pins[] = { 10, 11 };
++static unsigned vdsl_phy1_grp_pins[] = { 12, 13 };
++static unsigned vdsl_phy2_grp_pins[] = { 24, 25 };
++static unsigned vdsl_phy3_grp_pins[] = { 26, 27 };
++
++#define BCM63268_GROUP(n) \
++ { \
++ .name = #n, \
++ .pins = n##_pins, \
++ .num_pins = ARRAY_SIZE(n##_pins), \
++ }
++
++static struct bcm63268_pingroup bcm63268_groups[] = {
++ BCM63268_GROUP(gpio0),
++ BCM63268_GROUP(gpio1),
++ BCM63268_GROUP(gpio2),
++ BCM63268_GROUP(gpio3),
++ BCM63268_GROUP(gpio4),
++ BCM63268_GROUP(gpio5),
++ BCM63268_GROUP(gpio6),
++ BCM63268_GROUP(gpio7),
++ BCM63268_GROUP(gpio8),
++ BCM63268_GROUP(gpio9),
++ BCM63268_GROUP(gpio10),
++ BCM63268_GROUP(gpio11),
++ BCM63268_GROUP(gpio12),
++ BCM63268_GROUP(gpio13),
++ BCM63268_GROUP(gpio14),
++ BCM63268_GROUP(gpio15),
++ BCM63268_GROUP(gpio16),
++ BCM63268_GROUP(gpio17),
++ BCM63268_GROUP(gpio18),
++ BCM63268_GROUP(gpio19),
++ BCM63268_GROUP(gpio20),
++ BCM63268_GROUP(gpio21),
++ BCM63268_GROUP(gpio22),
++ BCM63268_GROUP(gpio23),
++ BCM63268_GROUP(gpio24),
++ BCM63268_GROUP(gpio25),
++ BCM63268_GROUP(gpio26),
++ BCM63268_GROUP(gpio27),
++ BCM63268_GROUP(gpio28),
++ BCM63268_GROUP(gpio29),
++ BCM63268_GROUP(gpio30),
++ BCM63268_GROUP(gpio31),
++ BCM63268_GROUP(gpio32),
++ BCM63268_GROUP(gpio33),
++ BCM63268_GROUP(gpio34),
++ BCM63268_GROUP(gpio35),
++ BCM63268_GROUP(gpio36),
++ BCM63268_GROUP(gpio37),
++ BCM63268_GROUP(gpio38),
++ BCM63268_GROUP(gpio39),
++ BCM63268_GROUP(gpio40),
++ BCM63268_GROUP(gpio41),
++ BCM63268_GROUP(gpio42),
++ BCM63268_GROUP(gpio43),
++ BCM63268_GROUP(gpio44),
++ BCM63268_GROUP(gpio45),
++ BCM63268_GROUP(gpio46),
++ BCM63268_GROUP(gpio47),
++ BCM63268_GROUP(gpio48),
++ BCM63268_GROUP(gpio49),
++ BCM63268_GROUP(gpio50),
++ BCM63268_GROUP(gpio51),
++
++ /* multi pin groups */
++ BCM63268_GROUP(nand_grp),
++ BCM63268_GROUP(dectpd_grp),
++ BCM63268_GROUP(vdsl_phy0_grp),
++ BCM63268_GROUP(vdsl_phy1_grp),
++ BCM63268_GROUP(vdsl_phy2_grp),
++ BCM63268_GROUP(vdsl_phy3_grp),
++};
++
++static const char * const led_groups[] = {
++ "gpio0",
++ "gpio1",
++ "gpio2",
++ "gpio3",
++ "gpio4",
++ "gpio5",
++ "gpio6",
++ "gpio7",
++ "gpio8",
++ "gpio9",
++ "gpio10",
++ "gpio11",
++ "gpio12",
++ "gpio13",
++ "gpio14",
++ "gpio15",
++ "gpio16",
++ "gpio17",
++ "gpio18",
++ "gpio19",
++ "gpio20",
++ "gpio21",
++ "gpio22",
++ "gpio23",
++};
++
++static const char * const serial_led_clk_groups[] = {
++ "gpio0",
++};
++
++static const char * const serial_led_data_groups[] = {
++ "gpio1",
++};
++
++static const char * const hsspi_cs4_groups[] = {
++ "gpio16",
++};
++
++static const char * const hsspi_cs5_groups[] = {
++ "gpio17",
++};
++
++static const char * const hsspi_cs6_groups[] = {
++ "gpio8",
++};
++
++static const char * const hsspi_cs7_groups[] = {
++ "gpio9",
++};
++
++static const char * const uart1_scts_groups[] = {
++ "gpio10",
++ "gpio24",
++};
++
++static const char * const uart1_srts_groups[] = {
++ "gpio11",
++ "gpio25",
++};
++
++static const char * const uart1_sdin_groups[] = {
++ "gpio12",
++ "gpio26",
++};
++
++static const char * const uart1_sdout_groups[] = {
++ "gpio13",
++ "gpio27",
++};
++
++static const char * const ntr_pulse_in_groups[] = {
++ "gpio14",
++ "gpio28",
++};
++
++static const char * const dsl_ntr_pulse_out_groups[] = {
++ "gpio15",
++ "gpio29",
++};
++
++static const char * const adsl_spi_miso_groups[] = {
++ "gpio18",
++};
++
++static const char * const adsl_spi_mosi_groups[] = {
++ "gpio19",
++};
++
++static const char * const vreg_clk_groups[] = {
++ "gpio22",
++};
++
++static const char * const pcie_clkreq_b_groups[] = {
++ "gpio23",
++};
++
++static const char * const switch_led_clk_groups[] = {
++ "gpio30",
++};
++
++static const char * const switch_led_data_groups[] = {
++ "gpio31",
++};
++
++static const char * const wifi_groups[] = {
++ "gpio32",
++ "gpio33",
++ "gpio34",
++ "gpio35",
++ "gpio36",
++ "gpio37",
++ "gpio38",
++ "gpio39",
++ "gpio40",
++ "gpio41",
++ "gpio42",
++ "gpio43",
++ "gpio44",
++ "gpio45",
++ "gpio46",
++ "gpio47",
++ "gpio48",
++ "gpio49",
++ "gpio50",
++ "gpio51",
++};
++
++static const char * const nand_groups[] = {
++ "nand_grp",
++};
++
++static const char * const dectpd_groups[] = {
++ "dectpd_grp",
++};
++
++static const char * const vdsl_phy_override_0_groups[] = {
++ "vdsl_phy_override_0_grp",
++};
++
++static const char * const vdsl_phy_override_1_groups[] = {
++ "vdsl_phy_override_1_grp",
++};
++
++static const char * const vdsl_phy_override_2_groups[] = {
++ "vdsl_phy_override_2_grp",
++};
++
++static const char * const vdsl_phy_override_3_groups[] = {
++ "vdsl_phy_override_3_grp",
++};
++
++#define BCM63268_LED_FUN(n) \
++ { \
++ .name = #n, \
++ .groups = n##_groups, \
++ .num_groups = ARRAY_SIZE(n##_groups), \
++ .reg = BCM63268_LEDCTRL, \
++ }
++
++#define BCM63268_MODE_FUN(n) \
++ { \
++ .name = #n, \
++ .groups = n##_groups, \
++ .num_groups = ARRAY_SIZE(n##_groups), \
++ .reg = BCM63268_MODE, \
++ }
++
++#define BCM63268_CTRL_FUN(n) \
++ { \
++ .name = #n, \
++ .groups = n##_groups, \
++ .num_groups = ARRAY_SIZE(n##_groups), \
++ .reg = BCM63268_CTRL, \
++ }
++
++#define BCM63268_BASEMODE_FUN(n, val) \
++ { \
++ .name = #n, \
++ .groups = n##_groups, \
++ .num_groups = ARRAY_SIZE(n##_groups), \
++ .reg = BCM63268_BASEMODE, \
++ .mask = val, \
++ }
++
++static const struct bcm63268_function bcm63268_funcs[] = {
++ BCM63268_LED_FUN(led),
++ BCM63268_MODE_FUN(serial_led_clk),
++ BCM63268_MODE_FUN(serial_led_data),
++ BCM63268_MODE_FUN(hsspi_cs6),
++ BCM63268_MODE_FUN(hsspi_cs7),
++ BCM63268_MODE_FUN(uart1_scts),
++ BCM63268_MODE_FUN(uart1_srts),
++ BCM63268_MODE_FUN(uart1_sdin),
++ BCM63268_MODE_FUN(uart1_sdout),
++ BCM63268_MODE_FUN(ntr_pulse_in),
++ BCM63268_MODE_FUN(dsl_ntr_pulse_out),
++ BCM63268_MODE_FUN(hsspi_cs4),
++ BCM63268_MODE_FUN(hsspi_cs5),
++ BCM63268_MODE_FUN(adsl_spi_miso),
++ BCM63268_MODE_FUN(adsl_spi_mosi),
++ BCM63268_MODE_FUN(vreg_clk),
++ BCM63268_MODE_FUN(pcie_clkreq_b),
++ BCM63268_MODE_FUN(switch_led_clk),
++ BCM63268_MODE_FUN(switch_led_data),
++ BCM63268_CTRL_FUN(wifi),
++ BCM63268_BASEMODE_FUN(nand, BASEMODE_NAND),
++ BCM63268_BASEMODE_FUN(dectpd, BASEMODE_DECTPD),
++ BCM63268_BASEMODE_FUN(vdsl_phy_override_0, BASEMODE_VDSL_PHY_0),
++ BCM63268_BASEMODE_FUN(vdsl_phy_override_1, BASEMODE_VDSL_PHY_1),
++ BCM63268_BASEMODE_FUN(vdsl_phy_override_2, BASEMODE_VDSL_PHY_2),
++ BCM63268_BASEMODE_FUN(vdsl_phy_override_3, BASEMODE_VDSL_PHY_3),
++};
++
++static int bcm63268_pinctrl_get_group_count(struct pinctrl_dev *pctldev)
++{
++ return ARRAY_SIZE(bcm63268_groups);
++}
++
++static const char *bcm63268_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
++ unsigned group)
++{
++ return bcm63268_groups[group].name;
++}
++
++static int bcm63268_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
++ unsigned group,
++ const unsigned **pins,
++ unsigned *num_pins)
++{
++ *pins = bcm63268_groups[group].pins;
++ *num_pins = bcm63268_groups[group].num_pins;
++
++ return 0;
++}
++
++static int bcm63268_pinctrl_get_func_count(struct pinctrl_dev *pctldev)
++{
++ return ARRAY_SIZE(bcm63268_funcs);
++}
++
++static const char *bcm63268_pinctrl_get_func_name(struct pinctrl_dev *pctldev,
++ unsigned selector)
++{
++ return bcm63268_funcs[selector].name;
++}
++
++static int bcm63268_pinctrl_get_groups(struct pinctrl_dev *pctldev,
++ unsigned selector,
++ const char * const **groups,
++ unsigned * const num_groups)
++{
++ *groups = bcm63268_funcs[selector].groups;
++ *num_groups = bcm63268_funcs[selector].num_groups;
++
++ return 0;
++}
++
++static void bcm63268_rmw_mux(struct bcm63268_pinctrl *pctl, void __iomem *reg,
++ u32 mask, u32 val)
++{
++ unsigned long flags;
++ u32 tmp;
++
++ spin_lock_irqsave(&pctl->lock, flags);
++ tmp = __raw_readl(reg);
++ tmp &= ~mask;
++ tmp |= val;
++ __raw_writel(tmp, reg);
++
++ spin_unlock_irqrestore(&pctl->lock, flags);
++}
++
++static void bcm63268_set_gpio(struct bcm63268_pinctrl *pctl, unsigned pin)
++{
++ const struct pinctrl_pin_desc *desc = &bcm63268_pins[pin];
++ u32 basemode = (unsigned long)desc->drv_data;
++ u32 mask = BIT(pin % 32);
++
++ if (basemode)
++ bcm63268_rmw_mux(pctl, pctl->basemode, basemode, 0);
++
++ if (pin < 32) {
++ /* base mode: 0 => gpio, 1 => mux function */
++ bcm63268_rmw_mux(pctl, pctl->mode, mask, 0);
++
++ /* pins 0-23 might be muxed to led */
++ if (pin < 24)
++ bcm63268_rmw_mux(pctl, pctl->led, mask, 0);
++ } else if (pin < 52) {
++ /* ctrl reg: 0 => wifi function, 1 => gpio */
++ bcm63268_rmw_mux(pctl, pctl->ctrl, mask, mask);
++ }
++}
++
++static int bcm63268_pinctrl_set_mux(struct pinctrl_dev *pctldev,
++ unsigned selector, unsigned group)
++{
++ struct bcm63268_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
++ const struct bcm63268_pingroup *grp = &bcm63268_groups[group];
++ const struct bcm63268_function *f = &bcm63268_funcs[selector];
++ unsigned i;
++ void __iomem *reg;
++ u32 val, mask;
++
++ for (i = 0; i < grp->num_pins; i++)
++ bcm63268_set_gpio(pctl, grp->pins[i]);
++
++ switch (f->reg) {
++ case BCM63268_LEDCTRL:
++ reg = pctl->led;
++ mask = BIT(grp->pins[0]);
++ val = BIT(grp->pins[0]);
++ break;
++ case BCM63268_MODE:
++ reg = pctl->mode;
++ mask = BIT(grp->pins[0]);
++ val = BIT(grp->pins[0]);
++ break;
++ case BCM63268_CTRL:
++ reg = pctl->ctrl;
++ mask = BIT(grp->pins[0]);
++ val = 0;
++ break;
++ case BCM63268_BASEMODE:
++ reg = pctl->basemode;
++ mask = f->mask;
++ val = f->mask;
++ break;
++ default:
++ WARN_ON(1);
++ return -EINVAL;
++ }
++
++ bcm63268_rmw_mux(pctl, reg, mask, val);
++
++ return 0;
++}
++
++static int bcm63268_gpio_request_enable(struct pinctrl_dev *pctldev,
++ struct pinctrl_gpio_range *range,
++ unsigned offset)
++{
++ struct bcm63268_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
++
++ /* disable all functions using this pin */
++ bcm63268_set_gpio(pctl, offset);
++
++ return 0;
++}
++
++static struct pinctrl_ops bcm63268_pctl_ops = {
++ .get_groups_count = bcm63268_pinctrl_get_group_count,
++ .get_group_name = bcm63268_pinctrl_get_group_name,
++ .get_group_pins = bcm63268_pinctrl_get_group_pins,
++#ifdef CONFIG_OF
++ .dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
++ .dt_free_map = pinctrl_utils_free_map,
++#endif
++};
++
++static struct pinmux_ops bcm63268_pmx_ops = {
++ .get_functions_count = bcm63268_pinctrl_get_func_count,
++ .get_function_name = bcm63268_pinctrl_get_func_name,
++ .get_function_groups = bcm63268_pinctrl_get_groups,
++ .set_mux = bcm63268_pinctrl_set_mux,
++ .gpio_request_enable = bcm63268_gpio_request_enable,
++ .strict = true,
++};
++
++static int bcm63268_pinctrl_probe(struct platform_device *pdev)
++{
++ struct bcm63268_pinctrl *pctl;
++ struct resource *res;
++ void __iomem *led, *mode, *ctrl, *basemode;
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "led");
++ led = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(led))
++ return PTR_ERR(led);
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mode");
++ mode = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(mode))
++ return PTR_ERR(mode);
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ctrl");
++ ctrl = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(ctrl))
++ return PTR_ERR(ctrl);
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "basemode");
++ basemode = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(basemode))
++ return PTR_ERR(basemode);
++
++ pctl = devm_kzalloc(&pdev->dev, sizeof(*pctl), GFP_KERNEL);
++ if (!pctl)
++ return -ENOMEM;
++
++ spin_lock_init(&pctl->lock);
++
++ pctl->led = led;
++ pctl->mode = mode;
++ pctl->ctrl = ctrl;
++ pctl->basemode = basemode;
++
++ pctl->desc.name = dev_name(&pdev->dev);
++ pctl->desc.owner = THIS_MODULE;
++ pctl->desc.pctlops = &bcm63268_pctl_ops;
++ pctl->desc.pmxops = &bcm63268_pmx_ops;
++
++ pctl->desc.npins = ARRAY_SIZE(bcm63268_pins);
++ pctl->desc.pins = bcm63268_pins;
++
++ platform_set_drvdata(pdev, pctl);
++
++ pctl->pctldev = bcm63xx_pinctrl_register(pdev, &pctl->desc, pctl,
++ pctl->gpio, BCM63268_NGPIO);
++ if (IS_ERR(pctl->pctldev))
++ return PTR_ERR(pctl->pctldev);
++
++ return 0;
++}
++
++static const struct of_device_id bcm63268_pinctrl_match[] = {
++ { .compatible = "brcm,bcm63268-pinctrl", },
++ { },
++};
++
++static struct platform_driver bcm63268_pinctrl_driver = {
++ .probe = bcm63268_pinctrl_probe,
++ .driver = {
++ .name = "bcm63268-pinctrl",
++ .of_match_table = bcm63268_pinctrl_match,
++ },
++};
++
++builtin_platform_driver(bcm63268_pinctrl_driver);
static const char * const gpio_chip_labels[] = {
"bcm63xx-gpio.0",
"bcm63xx-gpio.1",
-@@ -48,8 +50,9 @@ static void __init bcm63xx_gpio_init_one
+@@ -48,8 +50,10 @@ static void __init bcm63xx_gpio_init_one
pdata.base = id * 32;
pdata.ngpio = ngpio;
- platform_device_register_resndata(NULL, "bcm63xx-gpio", id, res, 2,
- &pdata, sizeof(pdata));
-+ if (!board_of_device_present("gpio0"))
++ if (!board_of_device_present("gpio0") &&
++ !board_of_device_present("pinctrl"))
+ platform_device_register_resndata(NULL, "bcm63xx-gpio", id, res,
+ 2, &pdata, sizeof(pdata));
}
--- /dev/null
+From 8439e5d2e69f54a532bb5f8ec001b4b5a3035574 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Wed, 27 Jul 2016 11:38:05 +0200
+Subject: [PATCH 14/16] Documentation: add BCM6318 pincontroller binding
+ documentation
+
+Add binding documentation for the pincontrol core found in BCM6318 SoCs.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ .../bindings/pinctrl/brcm,bcm6318-pinctrl.txt | 79 ++++++++++++++++++++++
+ 1 file changed, 79 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/pinctrl/brcm,bcm6318-pinctrl.txt
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6318-pinctrl.txt
+@@ -0,0 +1,79 @@
++* Broadcom BCM6318 pin controller
++
++Required properties:
++- compatible: Must be "brcm,bcm6318-pinctrl".
++- regs: Register specifiers of dirout, dat, mode, mux, and pad registers.
++- reg-names: Must be "dirout", "dat", "mode", "mux", "pad".
++- gpio-controller: Identifies this node as a gpio controller.
++- #gpio-cells: Must be <2>.
++
++Example:
++
++pinctrl: pin-controller@10000080 {
++ compatible = "brcm,bcm6318-pinctrl";
++ reg = <0x10000080 0x08>,
++ <0x10000088 0x08>,
++ <0x10000098 0x04>,
++ <0x1000009c 0x0c>,
++ <0x100000d4 0x18>;
++ reg-names = "dirout", "dat", "mode", "mux", "pad";
++
++ gpio-controller;
++ #gpio-cells = <2>;
++};
++
++
++Available pins/groups and functions:
++
++name pins functions
++-----------------------------------------------------------
++gpio0 0 led, ephy0_spd_led
++gpio1 1 led, ephy1_spd_led
++gpio2 2 led, ephy2_spd_led
++gpio3 3 led, ephy3_spd_led
++gpio4 4 led, ephy0_act_led
++gpio5 5 led, ephy1_act_led
++gpio6 6 led, ephy2_act_led, serial_led_data
++gpio7 7 led, ephy3_act_led, serial_led_clk
++gpio8 8 led, inet_act_led
++gpio9 9 led, inet_fail_led
++gpio10 10 led, dsl_led
++gpio11 11 led, post_fail_led
++gpio12 12 led, wlan_wps_led
++gpio13 13 led, usb_pwron, usb_device_led
++gpio14 14 led
++gpio15 15 led
++gpio16 16 led
++gpio17 17 led
++gpio18 18 led
++gpio19 19 led
++gpio20 20 led
++gpio21 21 led
++gpio22 22 led
++gpio23 23 led
++gpio24 24 -
++gpio25 25 -
++gpio26 26 -
++gpio27 27 -
++gpio28 28 -
++gpio29 29 -
++gpio30 30 -
++gpio31 31 -
++gpio32 32 -
++gpio33 33 -
++gpio34 34 -
++gpio35 35 -
++gpio36 36 -
++gpio37 37 -
++gpio38 38 -
++gpio39 39 -
++gpio40 40 usb_active
++gpio41 41 -
++gpio42 42 -
++gpio43 43 -
++gpio44 44 -
++gpio45 45 -
++gpio46 46 -
++gpio47 47 -
++gpio48 48 -
++gpio49 49 -
+++ /dev/null
-From 8940437e017d446d61a035e847c2a1d7a57a4354 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Wed, 1 Feb 2017 12:17:13 +0100
-Subject: [PATCH] brcm63xx: setup pinctrl for internal switch leds on bcm6368
-
----
- arch/mips/bcm63xx/boards/board_common.c | 9 +++++++++
- 1 file changed, 9 insertions(+)
-
---- a/arch/mips/bcm63xx/boards/board_common.c
-+++ b/arch/mips/bcm63xx/boards/board_common.c
-@@ -104,6 +104,15 @@ void __init board_early_setup(const stru
- GPIO_MODE_6348_G0_EXT_MII;
- }
-
-+ if (BCMCPU_IS_6368() && board.has_enetsw) {
-+ int i;
-+
-+ for (i = 0; i < 4; i++) {
-+ if (board.enetsw.used_ports[i].used)
-+ val |= (GPIO_MODE_6368_EPHY0_LED << i);
-+ }
-+ }
-+
- bcm_gpio_writel(val, GPIO_MODE_REG);
-
- #if IS_ENABLED(CONFIG_USB)
--- /dev/null
+From bd9c250ef85e6f99aa5d59b21abb87d0a48f2f61 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jonas.gorski@gmail.com>
+Date: Fri, 24 Jun 2016 22:20:39 +0200
+Subject: [PATCH 15/16] pinctrl: add a pincontrol driver for BCM6318
+
+Add a pincontrol driver for BCM6318. BCM6318 allows muxing most GPIOs
+to different functions. BCM6318 is similar to BCM6328 with the addition
+of a pad register, and the GPIO meaning of the mux register changes
+based on the GPIO number.
+
+Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
+---
+ drivers/pinctrl/bcm63xx/Kconfig | 7 +
+ drivers/pinctrl/bcm63xx/Makefile | 1 +
+ drivers/pinctrl/bcm63xx/pinctrl-bcm6318.c | 564 ++++++++++++++++++++++++++++++
+ 3 files changed, 572 insertions(+)
+ create mode 100644 drivers/pinctrl/bcm63xx/pinctrl-bcm6318.c
+
+--- a/drivers/pinctrl/bcm63xx/Kconfig
++++ b/drivers/pinctrl/bcm63xx/Kconfig
+@@ -2,6 +2,13 @@ config PINCTRL_BCM63XX
+ bool
+ select GPIO_GENERIC
+
++config PINCTRL_BCM6318
++ bool "BCM6318 pincontrol driver" if COMPILE_TEST
++ select PINMUX
++ select PINCONF
++ select PINCTRL_BCM63XX
++ select GENERIC_PINCONF
++
+ config PINCTRL_BCM6328
+ bool "BCM6328 pincontrol driver" if COMPILE_TEST
+ select PINMUX
+--- a/drivers/pinctrl/bcm63xx/Makefile
++++ b/drivers/pinctrl/bcm63xx/Makefile
+@@ -1,4 +1,5 @@
+ obj-$(CONFIG_PINCTRL_BCM63XX) += pinctrl-bcm63xx.o
++obj-$(CONFIG_PINCTRL_BCM6318) += pinctrl-bcm6318.o
+ obj-$(CONFIG_PINCTRL_BCM6328) += pinctrl-bcm6328.o
+ obj-$(CONFIG_PINCTRL_BCM6348) += pinctrl-bcm6348.o
+ obj-$(CONFIG_PINCTRL_BCM6358) += pinctrl-bcm6358.o
+--- /dev/null
++++ b/drivers/pinctrl/bcm63xx/pinctrl-bcm6318.c
+@@ -0,0 +1,564 @@
++/*
++ * This file is subject to the terms and conditions of the GNU General Public
++ * License. See the file "COPYING" in the main directory of this archive
++ * for more details.
++ *
++ * Copyright (C) 2016 Jonas Gorski <jonas.gorski@gmail.com>
++ */
++
++#include <linux/kernel.h>
++#include <linux/spinlock.h>
++#include <linux/bitops.h>
++#include <linux/gpio.h>
++#include <linux/gpio/driver.h>
++#include <linux/of.h>
++#include <linux/of_gpio.h>
++#include <linux/slab.h>
++#include <linux/platform_device.h>
++
++#include <linux/pinctrl/pinconf.h>
++#include <linux/pinctrl/pinconf-generic.h>
++#include <linux/pinctrl/pinmux.h>
++#include <linux/pinctrl/machine.h>
++
++#include "../core.h"
++#include "../pinctrl-utils.h"
++
++#include "pinctrl-bcm63xx.h"
++
++#define BCM6318_NGPIO 50
++
++struct bcm6318_pingroup {
++ const char *name;
++ const unsigned * const pins;
++ const unsigned num_pins;
++};
++
++struct bcm6318_function {
++ const char *name;
++ const char * const *groups;
++ const unsigned num_groups;
++
++ unsigned mode_val:1;
++ unsigned mux_val:2;
++};
++
++struct bcm6318_pinctrl {
++ struct pinctrl_dev *pctldev;
++ struct pinctrl_desc desc;
++
++ void __iomem *mode;
++ void __iomem *mux[3];
++ void __iomem *pad[6];
++
++ /* register access lock */
++ spinlock_t lock;
++
++ struct gpio_chip gpio[2];
++};
++
++static const struct pinctrl_pin_desc bcm6318_pins[] = {
++ PINCTRL_PIN(0, "gpio0"),
++ PINCTRL_PIN(1, "gpio1"),
++ PINCTRL_PIN(2, "gpio2"),
++ PINCTRL_PIN(3, "gpio3"),
++ PINCTRL_PIN(4, "gpio4"),
++ PINCTRL_PIN(5, "gpio5"),
++ PINCTRL_PIN(6, "gpio6"),
++ PINCTRL_PIN(7, "gpio7"),
++ PINCTRL_PIN(8, "gpio8"),
++ PINCTRL_PIN(9, "gpio9"),
++ PINCTRL_PIN(10, "gpio10"),
++ PINCTRL_PIN(11, "gpio11"),
++ PINCTRL_PIN(12, "gpio12"),
++ PINCTRL_PIN(13, "gpio13"),
++ PINCTRL_PIN(14, "gpio14"),
++ PINCTRL_PIN(15, "gpio15"),
++ PINCTRL_PIN(16, "gpio16"),
++ PINCTRL_PIN(17, "gpio17"),
++ PINCTRL_PIN(18, "gpio18"),
++ PINCTRL_PIN(19, "gpio19"),
++ PINCTRL_PIN(20, "gpio20"),
++ PINCTRL_PIN(21, "gpio21"),
++ PINCTRL_PIN(22, "gpio22"),
++ PINCTRL_PIN(23, "gpio23"),
++ PINCTRL_PIN(24, "gpio24"),
++ PINCTRL_PIN(25, "gpio25"),
++ PINCTRL_PIN(26, "gpio26"),
++ PINCTRL_PIN(27, "gpio27"),
++ PINCTRL_PIN(28, "gpio28"),
++ PINCTRL_PIN(29, "gpio29"),
++ PINCTRL_PIN(30, "gpio30"),
++ PINCTRL_PIN(31, "gpio31"),
++ PINCTRL_PIN(32, "gpio32"),
++ PINCTRL_PIN(33, "gpio33"),
++ PINCTRL_PIN(34, "gpio34"),
++ PINCTRL_PIN(35, "gpio35"),
++ PINCTRL_PIN(36, "gpio36"),
++ PINCTRL_PIN(37, "gpio37"),
++ PINCTRL_PIN(38, "gpio38"),
++ PINCTRL_PIN(39, "gpio39"),
++ PINCTRL_PIN(40, "gpio40"),
++ PINCTRL_PIN(41, "gpio41"),
++ PINCTRL_PIN(42, "gpio42"),
++ PINCTRL_PIN(43, "gpio43"),
++ PINCTRL_PIN(44, "gpio44"),
++ PINCTRL_PIN(45, "gpio45"),
++ PINCTRL_PIN(46, "gpio46"),
++ PINCTRL_PIN(47, "gpio47"),
++ PINCTRL_PIN(48, "gpio48"),
++ PINCTRL_PIN(49, "gpio49"),
++};
++
++static unsigned gpio0_pins[] = { 0 };
++static unsigned gpio1_pins[] = { 1 };
++static unsigned gpio2_pins[] = { 2 };
++static unsigned gpio3_pins[] = { 3 };
++static unsigned gpio4_pins[] = { 4 };
++static unsigned gpio5_pins[] = { 5 };
++static unsigned gpio6_pins[] = { 6 };
++static unsigned gpio7_pins[] = { 7 };
++static unsigned gpio8_pins[] = { 8 };
++static unsigned gpio9_pins[] = { 9 };
++static unsigned gpio10_pins[] = { 10 };
++static unsigned gpio11_pins[] = { 11 };
++static unsigned gpio12_pins[] = { 12 };
++static unsigned gpio13_pins[] = { 13 };
++static unsigned gpio14_pins[] = { 14 };
++static unsigned gpio15_pins[] = { 15 };
++static unsigned gpio16_pins[] = { 16 };
++static unsigned gpio17_pins[] = { 17 };
++static unsigned gpio18_pins[] = { 18 };
++static unsigned gpio19_pins[] = { 19 };
++static unsigned gpio20_pins[] = { 20 };
++static unsigned gpio21_pins[] = { 21 };
++static unsigned gpio22_pins[] = { 22 };
++static unsigned gpio23_pins[] = { 23 };
++static unsigned gpio24_pins[] = { 24 };
++static unsigned gpio25_pins[] = { 25 };
++static unsigned gpio26_pins[] = { 26 };
++static unsigned gpio27_pins[] = { 27 };
++static unsigned gpio28_pins[] = { 28 };
++static unsigned gpio29_pins[] = { 29 };
++static unsigned gpio30_pins[] = { 30 };
++static unsigned gpio31_pins[] = { 31 };
++static unsigned gpio32_pins[] = { 32 };
++static unsigned gpio33_pins[] = { 33 };
++static unsigned gpio34_pins[] = { 34 };
++static unsigned gpio35_pins[] = { 35 };
++static unsigned gpio36_pins[] = { 36 };
++static unsigned gpio37_pins[] = { 37 };
++static unsigned gpio38_pins[] = { 38 };
++static unsigned gpio39_pins[] = { 39 };
++static unsigned gpio40_pins[] = { 40 };
++static unsigned gpio41_pins[] = { 41 };
++static unsigned gpio42_pins[] = { 42 };
++static unsigned gpio43_pins[] = { 43 };
++static unsigned gpio44_pins[] = { 44 };
++static unsigned gpio45_pins[] = { 45 };
++static unsigned gpio46_pins[] = { 46 };
++static unsigned gpio47_pins[] = { 47 };
++static unsigned gpio48_pins[] = { 48 };
++static unsigned gpio49_pins[] = { 49 };
++
++#define BCM6318_GROUP(n) \
++ { \
++ .name = #n, \
++ .pins = n##_pins, \
++ .num_pins = ARRAY_SIZE(n##_pins), \
++ }
++
++static struct bcm6318_pingroup bcm6318_groups[] = {
++ BCM6318_GROUP(gpio0),
++ BCM6318_GROUP(gpio1),
++ BCM6318_GROUP(gpio2),
++ BCM6318_GROUP(gpio3),
++ BCM6318_GROUP(gpio4),
++ BCM6318_GROUP(gpio5),
++ BCM6318_GROUP(gpio6),
++ BCM6318_GROUP(gpio7),
++ BCM6318_GROUP(gpio8),
++ BCM6318_GROUP(gpio9),
++ BCM6318_GROUP(gpio10),
++ BCM6318_GROUP(gpio11),
++ BCM6318_GROUP(gpio12),
++ BCM6318_GROUP(gpio13),
++ BCM6318_GROUP(gpio14),
++ BCM6318_GROUP(gpio15),
++ BCM6318_GROUP(gpio16),
++ BCM6318_GROUP(gpio17),
++ BCM6318_GROUP(gpio18),
++ BCM6318_GROUP(gpio19),
++ BCM6318_GROUP(gpio20),
++ BCM6318_GROUP(gpio21),
++ BCM6318_GROUP(gpio22),
++ BCM6318_GROUP(gpio23),
++ BCM6318_GROUP(gpio24),
++ BCM6318_GROUP(gpio25),
++ BCM6318_GROUP(gpio26),
++ BCM6318_GROUP(gpio27),
++ BCM6318_GROUP(gpio28),
++ BCM6318_GROUP(gpio29),
++ BCM6318_GROUP(gpio30),
++ BCM6318_GROUP(gpio31),
++ BCM6318_GROUP(gpio32),
++ BCM6318_GROUP(gpio33),
++ BCM6318_GROUP(gpio34),
++ BCM6318_GROUP(gpio35),
++ BCM6318_GROUP(gpio36),
++ BCM6318_GROUP(gpio37),
++ BCM6318_GROUP(gpio38),
++ BCM6318_GROUP(gpio39),
++ BCM6318_GROUP(gpio40),
++ BCM6318_GROUP(gpio41),
++ BCM6318_GROUP(gpio42),
++ BCM6318_GROUP(gpio43),
++ BCM6318_GROUP(gpio44),
++ BCM6318_GROUP(gpio45),
++ BCM6318_GROUP(gpio46),
++ BCM6318_GROUP(gpio47),
++ BCM6318_GROUP(gpio48),
++ BCM6318_GROUP(gpio49),
++};
++
++/* GPIO_MODE */
++static const char * const led_groups[] = {
++ "gpio0",
++ "gpio1",
++ "gpio2",
++ "gpio3",
++ "gpio4",
++ "gpio5",
++ "gpio6",
++ "gpio7",
++ "gpio8",
++ "gpio9",
++ "gpio10",
++ "gpio11",
++ "gpio12",
++ "gpio13",
++ "gpio14",
++ "gpio15",
++ "gpio16",
++ "gpio17",
++ "gpio18",
++ "gpio19",
++ "gpio20",
++ "gpio21",
++ "gpio22",
++ "gpio23",
++};
++
++/* PINMUX_SEL */
++static const char * const ephy0_spd_led_groups[] = {
++ "gpio0",
++};
++
++static const char * const ephy1_spd_led_groups[] = {
++ "gpio1",
++};
++
++static const char * const ephy2_spd_led_groups[] = {
++ "gpio2",
++};
++
++static const char * const ephy3_spd_led_groups[] = {
++ "gpio3",
++};
++
++static const char * const ephy0_act_led_groups[] = {
++ "gpio4",
++};
++
++static const char * const ephy1_act_led_groups[] = {
++ "gpio5",
++};
++
++static const char * const ephy2_act_led_groups[] = {
++ "gpio6",
++};
++
++static const char * const ephy3_act_led_groups[] = {
++ "gpio7",
++};
++
++static const char * const serial_led_data_groups[] = {
++ "gpio6",
++};
++
++static const char * const serial_led_clk_groups[] = {
++ "gpio7",
++};
++
++static const char * const inet_act_led_groups[] = {
++ "gpio8",
++};
++
++static const char * const inet_fail_led_groups[] = {
++ "gpio9",
++};
++
++static const char * const dsl_led_groups[] = {
++ "gpio10",
++};
++
++static const char * const post_fail_led_groups[] = {
++ "gpio11",
++};
++
++static const char * const wlan_wps_led_groups[] = {
++ "gpio12",
++};
++
++static const char * const usb_pwron_groups[] = {
++ "gpio13",
++};
++
++static const char * const usb_device_led_groups[] = {
++ "gpio13",
++};
++
++static const char * const usb_active_groups[] = {
++ "gpio40",
++};
++
++#define BCM6318_MODE_FUN(n) \
++ { \
++ .name = #n, \
++ .groups = n##_groups, \
++ .num_groups = ARRAY_SIZE(n##_groups), \
++ .mode_val = 1, \
++ }
++
++#define BCM6318_MUX_FUN(n, mux) \
++ { \
++ .name = #n, \
++ .groups = n##_groups, \
++ .num_groups = ARRAY_SIZE(n##_groups), \
++ .mux_val = mux, \
++ }
++
++static const struct bcm6318_function bcm6318_funcs[] = {
++ BCM6318_MODE_FUN(led),
++ BCM6318_MUX_FUN(ephy0_spd_led, 1),
++ BCM6318_MUX_FUN(ephy1_spd_led, 1),
++ BCM6318_MUX_FUN(ephy2_spd_led, 1),
++ BCM6318_MUX_FUN(ephy3_spd_led, 1),
++ BCM6318_MUX_FUN(ephy0_act_led, 1),
++ BCM6318_MUX_FUN(ephy1_act_led, 1),
++ BCM6318_MUX_FUN(ephy2_act_led, 1),
++ BCM6318_MUX_FUN(ephy3_act_led, 1),
++ BCM6318_MUX_FUN(serial_led_data, 3),
++ BCM6318_MUX_FUN(serial_led_clk, 3),
++ BCM6318_MUX_FUN(inet_act_led, 1),
++ BCM6318_MUX_FUN(inet_fail_led, 1),
++ BCM6318_MUX_FUN(dsl_led, 1),
++ BCM6318_MUX_FUN(post_fail_led, 1),
++ BCM6318_MUX_FUN(wlan_wps_led, 1),
++ BCM6318_MUX_FUN(usb_pwron, 1),
++ BCM6318_MUX_FUN(usb_device_led, 2),
++ BCM6318_MUX_FUN(usb_active, 2),
++};
++
++static int bcm6318_pinctrl_get_group_count(struct pinctrl_dev *pctldev)
++{
++ return ARRAY_SIZE(bcm6318_groups);
++}
++
++static const char *bcm6318_pinctrl_get_group_name(struct pinctrl_dev *pctldev,
++ unsigned group)
++{
++ return bcm6318_groups[group].name;
++}
++
++static int bcm6318_pinctrl_get_group_pins(struct pinctrl_dev *pctldev,
++ unsigned group, const unsigned **pins,
++ unsigned *num_pins)
++{
++ *pins = bcm6318_groups[group].pins;
++ *num_pins = bcm6318_groups[group].num_pins;
++
++ return 0;
++}
++
++static int bcm6318_pinctrl_get_func_count(struct pinctrl_dev *pctldev)
++{
++ return ARRAY_SIZE(bcm6318_funcs);
++}
++
++static const char *bcm6318_pinctrl_get_func_name(struct pinctrl_dev *pctldev,
++ unsigned selector)
++{
++ return bcm6318_funcs[selector].name;
++}
++
++static int bcm6318_pinctrl_get_groups(struct pinctrl_dev *pctldev,
++ unsigned selector,
++ const char * const **groups,
++ unsigned * const num_groups)
++{
++ *groups = bcm6318_funcs[selector].groups;
++ *num_groups = bcm6318_funcs[selector].num_groups;
++
++ return 0;
++}
++
++static void bcm6318_rmw_mux(struct bcm6318_pinctrl *pctl, unsigned pin,
++ u32 mode, u32 mux)
++{
++ unsigned long flags;
++ u32 reg;
++
++ spin_lock_irqsave(&pctl->lock, flags);
++ if (pin < 32) {
++ reg = __raw_readl(pctl->mode);
++ reg &= ~BIT(pin);
++ if (mode)
++ reg |= BIT(pin);
++ __raw_writel(reg, pctl->mode);
++ }
++
++ if (pin < 48) {
++ reg = __raw_readl(pctl->mux[pin / 16]);
++ reg &= ~(3UL << ((pin % 16) * 2));
++ reg |= mux << ((pin % 16) * 2);
++ __raw_writel(reg, pctl->mux[pin / 16]);
++ }
++ spin_unlock_irqrestore(&pctl->lock, flags);
++}
++
++static void bcm6318_set_pad(struct bcm6318_pinctrl *pctl, unsigned pin, u8 val)
++{
++ unsigned long flags;
++ u32 reg;
++
++ spin_lock_irqsave(&pctl->lock, flags);
++ reg = __raw_readl(pctl->pad[pin / 8]);
++ reg &= ~(0xfUL << ((pin % 8) * 4));
++ reg |= val << ((pin % 8) * 4);
++ __raw_writel(reg, pctl->pad[pin / 8]);
++ spin_unlock_irqrestore(&pctl->lock, flags);
++}
++
++static int bcm6318_pinctrl_set_mux(struct pinctrl_dev *pctldev,
++ unsigned selector, unsigned group)
++{
++ struct bcm6318_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
++ const struct bcm6318_pingroup *grp = &bcm6318_groups[group];
++ const struct bcm6318_function *f = &bcm6318_funcs[selector];
++
++ bcm6318_rmw_mux(pctl, grp->pins[0], f->mode_val, f->mux_val);
++
++ return 0;
++}
++
++static int bcm6318_gpio_request_enable(struct pinctrl_dev *pctldev,
++ struct pinctrl_gpio_range *range,
++ unsigned offset)
++{
++ struct bcm6318_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
++
++ /* disable all functions using this pin */
++ if (offset < 13) {
++ /* GPIOs 0-12 use mux 0 as GPIO function */
++ bcm6318_rmw_mux(pctl, offset, 0, 0);
++ } else if (offset < 42) {
++ /* GPIOs 13-41 use mux 3 as GPIO function */
++ bcm6318_rmw_mux(pctl, offset, 0, 3);
++
++ /* FIXME: revert to old value for non gpio? */
++ bcm6318_set_pad(pctl, offset, 0);
++ } else {
++ /* no idea, really */
++ }
++
++ return 0;
++}
++
++static struct pinctrl_ops bcm6318_pctl_ops = {
++ .get_groups_count = bcm6318_pinctrl_get_group_count,
++ .get_group_name = bcm6318_pinctrl_get_group_name,
++ .get_group_pins = bcm6318_pinctrl_get_group_pins,
++#ifdef CONFIG_OF
++ .dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
++ .dt_free_map = pinctrl_utils_free_map,
++#endif
++};
++
++static struct pinmux_ops bcm6318_pmx_ops = {
++ .get_functions_count = bcm6318_pinctrl_get_func_count,
++ .get_function_name = bcm6318_pinctrl_get_func_name,
++ .get_function_groups = bcm6318_pinctrl_get_groups,
++ .set_mux = bcm6318_pinctrl_set_mux,
++ .gpio_request_enable = bcm6318_gpio_request_enable,
++ .strict = true,
++};
++
++static int bcm6318_pinctrl_probe(struct platform_device *pdev)
++{
++ struct bcm6318_pinctrl *pctl;
++ struct resource *res;
++ void __iomem *mode, *mux, *pad;
++ unsigned i;
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mode");
++ mode = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(mode))
++ return PTR_ERR(mode);
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mux");
++ mux = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(mux))
++ return PTR_ERR(mux);
++
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pad");
++ pad = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(pad))
++ return PTR_ERR(pad);
++
++ pctl = devm_kzalloc(&pdev->dev, sizeof(*pctl), GFP_KERNEL);
++ if (!pctl)
++ return -ENOMEM;
++
++ spin_lock_init(&pctl->lock);
++
++ pctl->mode = mode;
++
++ for (i = 0; i < 3; i++)
++ pctl->mux[i] = mux + (i * 4);
++
++ for (i = 0; i < 6; i++)
++ pctl->pad[i] = pad + (i * 4);
++
++ pctl->desc.name = dev_name(&pdev->dev);
++ pctl->desc.owner = THIS_MODULE;
++ pctl->desc.pctlops = &bcm6318_pctl_ops;
++ pctl->desc.pmxops = &bcm6318_pmx_ops;
++
++ pctl->desc.npins = ARRAY_SIZE(bcm6318_pins);
++ pctl->desc.pins = bcm6318_pins;
++
++ platform_set_drvdata(pdev, pctl);
++
++ pctl->pctldev = bcm63xx_pinctrl_register(pdev, &pctl->desc, pctl,
++ pctl->gpio, BCM6318_NGPIO);
++ if (IS_ERR(pctl->pctldev))
++ return PTR_ERR(pctl->pctldev);
++
++ return 0;
++}
++
++static const struct of_device_id bcm6318_pinctrl_match[] = {
++ { .compatible = "brcm,bcm6318-pinctrl", },
++ { },
++};
++
++static struct platform_driver bcm6318_pinctrl_driver = {
++ .probe = bcm6318_pinctrl_probe,
++ .driver = {
++ .name = "bcm6318-pinctrl",
++ .of_match_table = bcm6318_pinctrl_match,
++ },
++};
++
++builtin_platform_driver(bcm6318_pinctrl_driver);
--- /dev/null
+--- a/arch/mips/bcm63xx/Kconfig
++++ b/arch/mips/bcm63xx/Kconfig
+@@ -24,6 +24,8 @@ config BCM63XX_CPU_6318
+ select HW_HAS_PCI
+ select BCM63XX_OHCI
+ select BCM63XX_EHCI
++ select PINCTRL
++ select PINCTRL_BCM6318
+
+ config BCM63XX_CPU_6328
+ bool "support 6328 CPU"
+@@ -31,6 +33,8 @@ config BCM63XX_CPU_6328
+ select HW_HAS_PCI
+ select BCM63XX_OHCI
+ select BCM63XX_EHCI
++ select PINCTRL
++ select PINCTRL_BCM6328
+
+ config BCM63XX_CPU_6338
+ bool "support 6338 CPU"
+@@ -46,6 +50,8 @@ config BCM63XX_CPU_6348
+ select SYS_HAS_CPU_BMIPS32_3300
+ select HW_HAS_PCI
+ select BCM63XX_OHCI
++ select PINCTRL
++ select PINCTRL_BCM6348
+
+ config BCM63XX_CPU_6358
+ bool "support 6358 CPU"
+@@ -53,6 +59,8 @@ config BCM63XX_CPU_6358
+ select HW_HAS_PCI
+ select BCM63XX_OHCI
+ select BCM63XX_EHCI
++ select PINCTRL
++ select PINCTRL_BCM6358
+
+ config BCM63XX_CPU_6362
+ bool "support 6362 CPU"
+@@ -60,6 +68,8 @@ config BCM63XX_CPU_6362
+ select HW_HAS_PCI
+ select BCM63XX_OHCI
+ select BCM63XX_EHCI
++ select PINCTRL
++ select PINCTRL_BCM6362
+
+ config BCM63XX_CPU_6368
+ bool "support 6368 CPU"
+@@ -67,6 +77,8 @@ config BCM63XX_CPU_6368
+ select HW_HAS_PCI
+ select BCM63XX_OHCI
+ select BCM63XX_EHCI
++ select PINCTRL
++ select PINCTRL_BCM6368
+
+ config BCM63XX_CPU_63268
+ bool "support 63268 CPU"
+@@ -74,6 +86,8 @@ config BCM63XX_CPU_63268
+ select HW_HAS_PCI
+ select BCM63XX_OHCI
+ select BCM63XX_EHCI
++ select PINCTRL
++ select PINCTRL_BCM63268
+ endmenu
+
+ source "arch/mips/bcm63xx/boards/Kconfig"
#include <bcm63xx_dev_usb_ehci.h>
#include <bcm63xx_dev_usb_ohci.h>
#include <bcm63xx_dev_usb_usbd.h>
-@@ -250,10 +248,6 @@ int __init board_register_devices(void)
+@@ -241,10 +239,6 @@ int __init board_register_devices(void)
bcm63xx_register_fallback_sprom(&board.fallback_sprom)))
pr_err(PFX "failed to register fallback SPROM\n");
+ val |= GPIO_MODE_6358_ENET1_MII_CLK_INV;
}
- if (BCMCPU_IS_6368() && board.has_enetsw) {
+ bcm_gpio_writel(val, GPIO_MODE_REG);
--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
@@ -651,6 +651,8 @@
#include "board_common.h"
-@@ -189,6 +190,7 @@ static struct of_device_id of_ids[] = {
+@@ -180,6 +181,7 @@ static struct of_device_id of_ids[] = {
int __init board_register_devices(void)
{
int usbh_ports = 0;
#if CONFIG_OF
if (of_have_populated_dt()) {
-@@ -265,6 +267,10 @@ int __init board_register_devices(void)
+@@ -256,6 +258,10 @@ int __init board_register_devices(void)
board.ephy_reset_gpio_flags);
}
return;
--- a/arch/mips/bcm63xx/boards/board_common.c
+++ b/arch/mips/bcm63xx/boards/board_common.c
-@@ -269,7 +269,8 @@ int __init board_register_devices(void)
+@@ -260,7 +260,8 @@ int __init board_register_devices(void)
/* register any fixups */
for (i = 0; i < board.has_caldata; i++)
--- a/arch/mips/bcm63xx/boards/board_common.c
+++ b/arch/mips/bcm63xx/boards/board_common.c
-@@ -270,7 +270,7 @@ int __init board_register_devices(void)
+@@ -261,7 +261,7 @@ int __init board_register_devices(void)
/* register any fixups */
for (i = 0; i < board.has_caldata; i++)
pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset,
#include "board_common.h"
-@@ -268,9 +269,19 @@ int __init board_register_devices(void)
+@@ -259,9 +260,19 @@ int __init board_register_devices(void)
}
/* register any fixups */
projects / openwrt / staging / wigyori.git / commitdiff