ramips: add support for D-Link DWR-118-A2
authorCezary Jackiewicz <cezary@eko.one.pl>
Thu, 19 Apr 2018 17:34:22 +0000 (19:34 +0200)
committerMathias Kresin <dev@kresin.me>
Wed, 15 Aug 2018 05:42:36 +0000 (07:42 +0200)
The DWR-118-A2 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612EN)
- 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN)
- 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN)
- 2x external, non-detachable antennas
- 1x USB 2.0
- UART (J1) header on PCB (57600 8n1)
- 7x LED (5x GPIO-controlled), 2x button
- JBOOT bootloader

Known issues:
- GELAN not working
- flash is very slow

The status led has been assigned to the dwr-118-a2:green:internet led.
At the end of the boot it is switched off and is available for other
operation. Work correctly also during sysupgrade operation.

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
target/linux/ramips/base-files/etc/board.d/01_leds
target/linux/ramips/base-files/etc/board.d/02_network
target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
target/linux/ramips/base-files/lib/upgrade/platform.sh
target/linux/ramips/dts/DWR-118-A2.dts [new file with mode: 0644]
target/linux/ramips/image/mt7620.mk
target/linux/ramips/mt7620/config-4.14

index 4e90efd..44511bb 100755 (executable)
@@ -162,6 +162,13 @@ dlink,dwr-116-a1|\
 mzk-ex300np)
        set_wifi_led "$boardname:green:wifi"
        ;;
+dlink,dwr-118-a2)
+       ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x0e"
+       ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01"
+       set_wifi_led "$boardname:green:wlan2g" "wlan1"
+       set_usb_led "$boardname:green:usb"
+       ucidef_set_led_default "internet" "internet" "$boardname:green:internet" "0"
+       ;;
 dlink,dwr-921-c1)
        set_wifi_led "$boardname:green:wifi"
        ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x0f"
index 915c358..b6f70ef 100755 (executable)
@@ -157,6 +157,10 @@ ramips_setup_interfaces()
        wrh-300cr)
                ucidef_set_interface_lan "eth0"
                ;;
+       dlink,dwr-118-a2)
+               ucidef_add_switch "switch0" \
+                       "1:lan:2" "2:lan:1" "3:lan:3" "4:lan" "0:wan" "6@eth0"
+               ;;
        mir3g)
                ucidef_add_switch "switch0" \
                        "2:lan:2" "3:lan:1" "1:wan" "6t@eth0"
@@ -462,6 +466,7 @@ ramips_setup_macs()
                wan_mac=$(mtd_get_mac_ascii factory wanmac)
                ;;
        dlink,dwr-116-a1|\
+       dlink,dwr-118-a2|\
        dlink,dwr-921-c1)
                wan_mac=$(jboot_config_read -m -i $(find_mtd_part "config") -o 0xE000)
                lan_mac=$(macaddr_add "$wan_mac" 1)
index c0c6a3e..711b838 100644 (file)
@@ -55,6 +55,7 @@ case "$FIRMWARE" in
 "soc_wmac.eeprom")
        case $board in
        dlink,dwr-116-a1|\
+       dlink,dwr-118-a2|\
        dlink,dwr-921-c1)
                wan_mac=$(jboot_config_read -m -i $(find_mtd_part "config") -o 0xE000)
                wifi_mac=$(macaddr_add "$wan_mac" 1)
index a102a0b..67c032c 100755 (executable)
@@ -289,6 +289,7 @@ platform_check_image() {
                return 0
                ;;
        dlink,dwr-116-a1|\
+       dlink,dwr-118-a2|\
        dlink,dwr-921-c1|\
        dwr-512-b)
                [ "$magic" != "0404242b" ] && {
diff --git a/target/linux/ramips/dts/DWR-118-A2.dts b/target/linux/ramips/dts/DWR-118-A2.dts
new file mode 100644 (file)
index 0000000..f36ecb5
--- /dev/null
@@ -0,0 +1,179 @@
+/dts-v1/;
+
+#include "mt7620a.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+       compatible = "dlink,dwr-118-a2", "ralink,mt7620a-soc";
+       model = "D-Link DWR-118 A2";
+
+       aliases {
+               led-status = &led_internet;
+       };
+
+       gpio-keys-polled {
+               compatible = "gpio-keys-polled";
+               poll-interval = <20>;
+
+               wps {
+                       label = "wps";
+                       gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WPS_BUTTON>;
+               };
+
+               reset {
+                       label = "reset";
+                       gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+               };
+       };
+
+       gpio-leds {
+               compatible = "gpio-leds";
+
+               wan {
+                       label = "dwr-118-a2:green:wan";
+                       gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+               };
+
+               led_internet: internet {
+                       label = "dwr-118-a2:green:internet";
+                       gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+               };
+
+               lan {
+                       label = "dwr-118-a2:green:lan";
+                       gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+               };
+
+               wlan2g {
+                       label = "dwr-118-a2:green:wlan2g";
+                       gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+               };
+
+               usb {
+                       label = "dwr-118-a2:green:usb";
+                       gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+               };
+
+
+       };
+
+       gpio_export {
+               compatible = "gpio-export";
+               #size-cells = <0>;
+
+               usb {
+                       gpio-export,name = "usb";
+                       gpio-export,output = <1>;
+                       gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+       };
+    };
+};
+
+&gpio1 {
+       status = "okay";
+};
+
+&gpio2 {
+       status = "okay";
+};
+
+&gpio3 {
+       status = "okay";
+};
+
+&spi0 {
+       status = "okay";
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <50000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "jboot";
+                               reg = <0x0 0x10000>;
+                               read-only;
+                       };
+
+                       partition@10000 {
+                               label = "firmware";
+                               reg = <0x10000 0xfe0000>;
+                       };
+
+                       config: partition@ff0000 {
+                               label = "config";
+                               reg = <0xff0000 0x10000>;
+                               read-only;
+                       };
+               };
+       };
+};
+
+&ehci {
+       status = "okay";
+};
+
+&ohci {
+       status = "okay";
+};
+
+&pinctrl {
+       state_default: pinctrl0 {
+               default {
+                       ralink,group = "ephy", "uartf", "spi refclk", "wled";
+                       ralink,function = "gpio";
+               };
+       };
+};
+
+&pcie {
+       status = "okay";
+};
+
+&pcie0 {
+       wifi@0,0 {
+               reg = <0x0000 0 0 0 0>;
+               ieee80211-freq-limit = <5000000 6000000>;
+               mtd-mac-address = <&config 0xe4a8>;
+               mtd-mac-address-increment = <(2)>;
+
+               led {
+                       led-sources = <2>;
+                       led-active-low;
+               };
+       };
+};
+
+&ethernet {
+       status = "okay";
+       pinctrl-names = "default";
+       pinctrl-0 = <&rgmii1_pins &mdio_pins>;
+
+       port@4 {
+               status = "okay";
+               phy-handle = <&phy4>;
+               phy-mode = "rgmii";
+       };
+
+       mdio-bus {
+               status = "okay";
+
+               phy4: ethernet-phy@4 {
+                       reg = <4>;
+                       phy-mode = "rgmii";
+               };
+       };
+};
+
+&gsw {
+       mediatek,port4 = "gmac";
+};
index c759a89..c511a17 100644 (file)
@@ -164,6 +164,20 @@ define Device/dlink_dwr-116-a1
 endef
 TARGET_DEVICES += dlink_dwr-116-a1
 
+define Device/dlink_dwr-118-a2
+  DTS := DWR-118-A2
+  DEVICE_TITLE := D-Link DWR-118 A2
+  DEVICE_PACKAGES := kmod-usb2 jboot-tools kmod-mt76
+  DLINK_ROM_ID := DLK6E3814001
+  DLINK_FAMILY_MEMBER := 0x6E38
+  DLINK_FIRMWARE_SIZE := 0xFE0000
+  KERNEL := $(KERNEL_DTB)
+  IMAGES += factory.bin
+  IMAGE/sysupgrade.bin := mkdlinkfw | pad-rootfs | append-metadata
+  IMAGE/factory.bin := mkdlinkfw | pad-rootfs | mkdlinkfw-factory
+endef
+TARGET_DEVICES += dlink_dwr-118-a2
+
 define Device/dlink_dwr-921-c1
   DTS := DWR-921-C1
   IMAGE_SIZE := $(ralink_default_fw_size_16M)
index 89de071..1162ed4 100644 (file)
@@ -128,6 +128,7 @@ CONFIG_IRQ_INTC=y
 CONFIG_IRQ_MIPS_CPU=y
 CONFIG_IRQ_WORK=y
 CONFIG_LIBFDT=y
+CONFIG_MARVELL_PHY=y
 CONFIG_MDIO_BUS=y
 CONFIG_MDIO_DEVICE=y
 CONFIG_MFD_SYSCON=y