ipq40xx: add support for FritzBox 7530
authorDavid Bauer <mail@david-bauer.net>
Mon, 18 Feb 2019 22:58:34 +0000 (23:58 +0100)
committerChristian Lamparter <chunkeey@gmail.com>
Thu, 28 Feb 2019 10:32:55 +0000 (11:32 +0100)
Hardware
--------
CPU:   Qualcomm IPQ4019
RAM:   256M
FLASH: 128M NAND
ETH:   QCA8075
VDSL:  Intel/Lantiq VRX518 PCIe attached
       currently not supported
DECT:  Dialog SC14448
       currently not supported
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
LED:    - Power/DSL green
        - WLAN green
        - FON/DECT green
        - Connect/WPS green
        - Info green
        - Info red
BTN:    - WLAN
        - FON
        - WPS/Connect
UART:  115200n8 3.3V (located under the Dialog chip)
       VCC - RX - TX - GND (Square is VCC)

Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz7530'
   subdirectory. Place it in the same directory as the 'eva_ramboot.py'
   script. It is located in the 'scripts/flashing' subdirectory of the
   OpenWRT tree.

2. Assign yourself the IP address 192.168.178.10/24. Connect your
   Computer to one of the boxes LAN ports.

3. Connect Power to the Box. As soon as the LAN port of your computer
   shows link, load the U-Boot to the box using following command.

   > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin

4. The U-Boot will now start. Now assign yourself the IP address
   192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
   server root directory and rename it to 'FRITZ7530.bin'.

5. The Box will now boot OpenWRT from RAM. This can take up to two
   minutes.

6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
   scp. SSH into the Box and first write the Bootloader to both previous
   kernel partitions.

   > mtd write /path/to/uboot-fritz7530.bin uboot0
   > mtd write /path/to/uboot-fritz7530.bin uboot1

7. Remove the AVM filesystem partitions to make room for our kernel +
   rootfs + overlayfs.

   > ubirmvol /dev/ubi0 --name=avm_filesys_0
   > ubirmvol /dev/ubi0 --name=avm_filesys_1

8. Flash OpenWRT peristently using sysupgrade.

   > sysupgrade -n /path/to/openwrt-sysupgrade.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
[removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
12 files changed:
package/boot/uboot-fritz4040/Makefile
package/firmware/ipq-wifi/Makefile
package/firmware/ipq-wifi/board-avm_fritzbox-7530.bin [new file with mode: 0644]
target/linux/ipq40xx/base-files/etc/board.d/01_leds
target/linux/ipq40xx/base-files/etc/board.d/02_network
target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts [new file with mode: 0644]
target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts [new file with mode: 0644]
target/linux/ipq40xx/image/Makefile
target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch
target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch

index 36ee0be..9af09af 100644 (file)
@@ -30,6 +30,11 @@ define U-Boot/fritz4040
   BUILD_DEVICES:=avm_fritzbox-4040
 endef
 
+define U-Boot/fritz7530
+  NAME:=FritzBox 7530
+  BUILD_DEVICES:=avm_fritzbox-7530
+endef
+
 UBOOT_CONFIGURE_VARS += USE_PRIVATE_LIBGCC=yes
 UBOOT_MAKE_FLAGS = USE_PRIVATE_LIBGCC=yes
 export DTC
@@ -56,6 +61,6 @@ define Package/u-boot/install
        $(INSTALL_BIN) $(PKG_BUILD_DIR)/upload-to-f4040.sh $(1)/
 endef
 
-UBOOT_TARGETS := fritz4040
+UBOOT_TARGETS := fritz4040 fritz7530
 
 $(eval $(call BuildPackage/U-Boot))
index 62f54fc..9a00832 100644 (file)
@@ -18,7 +18,7 @@ endef
 # Please send a mail with your device-specific board files upstream.
 # You can find instructions and examples on the linux-wireless wiki:
 # <https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles>
-ALLWIFIBOARDS:=alfa-network_ap120c-ac asus_map-ac2200 engenius_eap1300 linksys_ea6350v3 qxwlan_e2600ac
+ALLWIFIBOARDS:=alfa-network_ap120c-ac asus_map-ac2200 avm_fritzbox-7530 engenius_eap1300 linksys_ea6350v3 qxwlan_e2600ac
 ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD))
 
 define Package/ipq-wifi-default
@@ -56,6 +56,7 @@ endef
 $(eval $(call generate-ipq-wifi-package,alfa-network_ap120c-ac,board-alfa-network_ap120c-ac.bin,ALFA Network AP120C-AC))
 $(eval $(call generate-ipq-wifi-package,asus_map-ac2200,board-map-ac2200.bin,ASUS MAP-AC2200))
 $(eval $(call generate-ipq-wifi-package,engenius_eap1300,board-engenius_eap1300.bin,EnGenius EAP1300))
+$(eval $(call generate-ipq-wifi-package,avm_fritzbox-7530,board-avm_fritzbox-7530.bin,AVM FRITZ!Box 7530))
 $(eval $(call generate-ipq-wifi-package,linksys_ea6350v3,board-linksys_ea6350v3.bin,Linksys EA6350v3))
 $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,board-qxwlan-e2600ac.bin,Qxwlan E2600AC))
 
diff --git a/package/firmware/ipq-wifi/board-avm_fritzbox-7530.bin b/package/firmware/ipq-wifi/board-avm_fritzbox-7530.bin
new file mode 100644 (file)
index 0000000..905145f
Binary files /dev/null and b/package/firmware/ipq-wifi/board-avm_fritzbox-7530.bin differ
index d23791e..dc656cb 100755 (executable)
@@ -25,15 +25,16 @@ avm,fritzbox-4040)
        ucidef_set_led_netdev "wan" "WAN" "fritz4040:green:wan" "eth1"
        ucidef_set_led_switch "lan" "LAN" "fritz4040:green:lan" "switch0" "0x1e"
        ;;
+avm,fritzbox-7530 |\
+glinet,gl-b1300)
+       ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
+       ;;
 engenius,eap1300)
        ucidef_set_led_netdev "lan" "LAN" "${boardname}:blue:lan" "eth0"
        ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:blue:wlan2g" "phy0tpt"
        ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:yellow:wlan5g" "phy1tpt"
        ucidef_set_led_default "mesh" "MESH" "${boardname}:blue:mesh" "0"
        ;;
-glinet,gl-b1300)
-       ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
-       ;;
 netgear,ex6100v2 |\
 netgear,ex6150v2)
        ucidef_set_led_wlan "wlan2g" "WLAN2G" "ex61x0v2:green:router" "phy0tpt"
index c0466ba..9c232d4 100755 (executable)
@@ -33,6 +33,10 @@ ipq40xx_setup_interfaces()
                ucidef_add_switch "switch0" \
                        "0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
                ;;
+       avm,fritzbox-7530)
+               ucidef_add_switch "switch0" \
+                       "0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
+               ;;
        compex,wpj428)
                ucidef_set_interface_lan "eth0 eth1"
                ;;
index 4442152..1264d2e 100644 (file)
@@ -135,6 +135,10 @@ case "$FIRMWARE" in
        avm,fritzbox-4040)
                /usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
                ;;
+       avm,fritzbox-7530)
+               /usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
+               /usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
+               ;;
        compex,wpj428 |\
        engenius,eap1300 |\
        openmesh,a42 |\
@@ -179,6 +183,10 @@ case "$FIRMWARE" in
        avm,fritzbox-4040)
                /usr/bin/fritz_cal_extract -i 1 -s 0x400 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader_config")
                ;;
+       avm,fritzbox-7530)
+               /usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \
+               /usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
+               ;;
        compex,wpj428 |\
        engenius,eap1300 |\
        openmesh,a42 |\
index 87e27af..9a2c13c 100644 (file)
@@ -48,6 +48,7 @@ platform_do_upgrade() {
        case "$(board_name)" in
        8dev,jalapeno |\
        alfa-network,ap120c-ac |\
+       avm,fritzbox-7530 |\
        qxwlan,e2600ac-c2)
                nand_do_upgrade "$ARGV"
                ;;
diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts
new file mode 100644 (file)
index 0000000..45c4864
--- /dev/null
@@ -0,0 +1,300 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+       model = "AVM FRITZ!Box 7530";
+       compatible = "avm,fritzbox-7530";
+
+       aliases {
+               led-boot = &power_green;
+               led-failsafe = &info_red;
+               led-running = &power_green;
+               led-upgrade = &info_green;
+       };
+
+       soc {
+               mdio@90000 {
+                       status = "okay";
+               };
+
+               ess-psgmii@98000 {
+                       status = "okay";
+               };
+
+               tcsr@1949000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1949000 0x100>;
+                       qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+               };
+
+               tcsr@194b000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x194b000 0x100>;
+                       qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+               };
+
+               ess_tcsr@1953000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1953000 0x1000>;
+                       qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+               };
+
+               tcsr@1957000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1957000 0x100>;
+                       qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+               };
+
+               usb3@8af8800 {
+                       status = "okay";
+               };
+
+               crypto@8e3a000 {
+                       status = "okay";
+               };
+
+               watchdog@b017000 {
+                       status = "okay";
+               };
+
+               ess-switch@c000000 {
+                       status = "okay";
+               };
+
+               edma@c080000 {
+                       status = "okay";
+                       qcom,num_gmac = <1>;
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               wlan {
+                       label = "wlan";
+                       gpios = <&tlmm 42 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RFKILL>;
+               };
+
+               wps {
+                       label = "wps";
+                       gpios = <&tlmm 41 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WPS_BUTTON>;
+               };
+
+               dect {
+                       label = "dect";
+                       gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_PHONE>;
+               };
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               info_red: info_red {
+                       label = "fritzbox-7530:red:info";
+                       gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+               };
+
+               info_green: info {
+                       label = "fritzbox-7530:green:info";
+                       gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+               };
+
+               wlan {
+                       label = "fritzbox-7530:green:wlan";
+                       gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
+               };
+
+               fon {
+                       label = "fritzbox-7530:green:fon";
+                       gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+               };
+
+               power_green: power {
+                       label = "fritzbox-7530:green:power";
+                       gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
+               };
+
+               wps {
+                       label = "fritzbox-7530:green:wps";
+                       gpios = <&tlmm 45 GPIO_ACTIVE_LOW>;
+               };
+       };
+};
+
+&tlmm {
+       serial_0_pins: serial_pinmux {
+               mux {
+                       pins = "gpio16", "gpio17";
+                       function = "blsp_uart0";
+                       bias-disable;
+               };
+       };
+
+       nand_pins: nand_pins {
+               pullups {
+                       pins = "gpio53", "gpio58", "gpio59";
+                       function = "qpic";
+                       bias-pull-up;
+               };
+
+               pulldowns {
+                       pins = "gpio54", "gpio55", "gpio56",
+                               "gpio57", "gpio60", "gpio61",
+                               "gpio62", "gpio63", "gpio64",
+                               "gpio65", "gpio66", "gpio67",
+                               "gpio68", "gpio69";
+                       function = "qpic";
+                       bias-pull-down;
+               };
+       };
+
+       usb-power {
+               line-name = "enable USB3 power";
+               gpios = <49 GPIO_ACTIVE_HIGH>;
+               gpio-hog;
+               output-high;
+       };
+};
+
+&nand {
+       pinctrl-0 = <&nand_pins>;
+       pinctrl-names = "default";
+       status = "okay";
+       cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+       nand@0 {
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "SBL1";
+                               reg = <0x000000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@80000 {
+                               label = "MIBIB";
+                               reg = <0x080000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@100000 {
+                               label = "QSEE";
+                               reg = <0x100000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@180000 {
+                               label = "CDT";
+                               reg = <0x180000 0x40000>;
+                               read-only;
+                       };
+
+                       partition@1c0000 {
+                               label = "QSEE_B";
+                               reg = <0x1c0000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@240000 {
+                               label = "urlader0";
+                               reg = <0x240000 0x40000>;
+                               read-only;
+                       };
+
+                       partition@280000 {
+                               label = "urlader1";
+                               reg = <0x280000 0x40000>;
+                               read-only;
+                       };
+
+                       partition@2c0000 {
+                               label = "nand-tffs";
+                               reg = <0x2c0000 0x840000>;
+                               read-only;
+                       };
+
+                       partition@b00000 {
+                               /* 'kernel1' in AVM firmware */
+                               label = "uboot0";
+                               reg = <0xb00000 0x400000>;
+                       };
+
+                       partition@f00000 {
+                               /* 'kernel2' in AVM firmware */
+                               label = "uboot1";
+                               reg = <0xf00000 0x400000>;
+                       };
+
+                       partition@1300000 {
+                               label = "ubi";
+                               reg = <0x1300000 0x6d00000>;
+                       };
+               };
+       };
+};
+
+&cryptobam {
+       status = "okay";
+};
+
+&blsp_dma {
+       status = "okay";
+};
+
+&blsp1_uart1 {
+       pinctrl-0 = <&serial_0_pins>;
+       pinctrl-names = "default";
+       status = "okay";
+};
+
+&usb3_ss_phy {
+       status = "okay";
+};
+
+&usb3_hs_phy {
+       status = "okay";
+};
+
+&qpic_bam {
+       status = "okay";
+};
+
+&wifi0 {
+       status = "okay";
+       qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530";
+};
+
+&wifi1 {
+       status = "okay";
+       qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530";
+};
+
+&pcie0 {
+       status = "okay";
+
+       perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+       wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+       bridge@0,0 {
+               reg = <0x00000000 0 0 0 0>;
+               #address-cells = <3>;
+               #size-cells = <2>;
+               ranges;
+
+               dsl@1,0 {
+                       compatible = "intel,vrx518";
+                       status = "okay";
+                       reg = <0x00010000 0 0 0 0>;
+               };
+       };
+};
diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-fritzbox-7530.dts
new file mode 100644 (file)
index 0000000..53f83f4
--- /dev/null
@@ -0,0 +1,304 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+       model = "AVM FRITZ!Box 7530";
+       compatible = "avm,fritzbox-7530";
+
+       aliases {
+               led-boot = &power_green;
+               led-failsafe = &info_red;
+               led-running = &power_green;
+               led-upgrade = &info_green;
+       };
+
+       soc {
+               rng@22000 {
+                       status = "okay";
+               };
+
+               mdio@90000 {
+                       status = "okay";
+               };
+
+               ess-psgmii@98000 {
+                       status = "okay";
+               };
+
+               tcsr@1949000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1949000 0x100>;
+                       qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+               };
+
+               tcsr@194b000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x194b000 0x100>;
+                       qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+               };
+
+               ess_tcsr@1953000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1953000 0x1000>;
+                       qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+               };
+
+               tcsr@1957000 {
+                       compatible = "qcom,tcsr";
+                       reg = <0x1957000 0x100>;
+                       qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+               };
+
+               usb3@8af8800 {
+                       status = "okay";
+               };
+
+               crypto@8e3a000 {
+                       status = "okay";
+               };
+
+               watchdog@b017000 {
+                       status = "okay";
+               };
+
+               ess-switch@c000000 {
+                       status = "okay";
+               };
+
+               edma@c080000 {
+                       status = "okay";
+                       qcom,num_gmac = <1>;
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               wlan {
+                       label = "wlan";
+                       gpios = <&tlmm 42 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RFKILL>;
+               };
+
+               wps {
+                       label = "wps";
+                       gpios = <&tlmm 41 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WPS_BUTTON>;
+               };
+
+               dect {
+                       label = "dect";
+                       gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_PHONE>;
+               };
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               info_red: info_red {
+                       label = "fritzbox-7530:red:info";
+                       gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+               };
+
+               info_green: info {
+                       label = "fritzbox-7530:green:info";
+                       gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+               };
+
+               wlan {
+                       label = "fritzbox-7530:green:wlan";
+                       gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
+               };
+
+               fon {
+                       label = "fritzbox-7530:green:fon";
+                       gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+               };
+
+               power_green: power {
+                       label = "fritzbox-7530:green:power";
+                       gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
+               };
+
+               wps {
+                       label = "fritzbox-7530:green:wps";
+                       gpios = <&tlmm 45 GPIO_ACTIVE_LOW>;
+               };
+       };
+};
+
+&tlmm {
+       serial_0_pins: serial_pinmux {
+               mux {
+                       pins = "gpio16", "gpio17";
+                       function = "blsp_uart0";
+                       bias-disable;
+               };
+       };
+
+       nand_pins: nand_pins {
+               pullups {
+                       pins = "gpio53", "gpio58", "gpio59";
+                       function = "qpic";
+                       bias-pull-up;
+               };
+
+               pulldowns {
+                       pins = "gpio54", "gpio55", "gpio56",
+                               "gpio57", "gpio60", "gpio61",
+                               "gpio62", "gpio63", "gpio64",
+                               "gpio65", "gpio66", "gpio67",
+                               "gpio68", "gpio69";
+                       function = "qpic";
+                       bias-pull-down;
+               };
+       };
+
+       usb-power {
+               line-name = "enable USB3 power";
+               gpios = <49 GPIO_ACTIVE_HIGH>;
+               gpio-hog;
+               output-high;
+       };
+};
+
+&nand {
+       pinctrl-0 = <&nand_pins>;
+       pinctrl-names = "default";
+       status = "okay";
+       cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+       nand@0 {
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "SBL1";
+                               reg = <0x000000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@80000 {
+                               label = "MIBIB";
+                               reg = <0x080000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@100000 {
+                               label = "QSEE";
+                               reg = <0x100000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@180000 {
+                               label = "CDT";
+                               reg = <0x180000 0x40000>;
+                               read-only;
+                       };
+
+                       partition@1c0000 {
+                               label = "QSEE_B";
+                               reg = <0x1c0000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@240000 {
+                               label = "urlader0";
+                               reg = <0x240000 0x40000>;
+                               read-only;
+                       };
+
+                       partition@280000 {
+                               label = "urlader1";
+                               reg = <0x280000 0x40000>;
+                               read-only;
+                       };
+
+                       partition@2c0000 {
+                               label = "nand-tffs";
+                               reg = <0x2c0000 0x840000>;
+                               read-only;
+                       };
+
+                       partition@b00000 {
+                               /* 'kernel1' in AVM firmware */
+                               label = "uboot0";
+                               reg = <0xb00000 0x400000>;
+                       };
+
+                       partition@f00000 {
+                               /* 'kernel2' in AVM firmware */
+                               label = "uboot1";
+                               reg = <0xf00000 0x400000>;
+                       };
+
+                       partition@1300000 {
+                               label = "ubi";
+                               reg = <0x1300000 0x6d00000>;
+                       };
+               };
+       };
+};
+
+&cryptobam {
+       status = "okay";
+};
+
+&blsp_dma {
+       status = "okay";
+};
+
+&blsp1_uart1 {
+       pinctrl-0 = <&serial_0_pins>;
+       pinctrl-names = "default";
+       status = "okay";
+};
+
+&usb3_ss_phy {
+       status = "okay";
+};
+
+&usb3_hs_phy {
+       status = "okay";
+};
+
+&qpic_bam {
+       status = "okay";
+};
+
+&wifi0 {
+       status = "okay";
+       qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530";
+};
+
+&wifi1 {
+       status = "okay";
+       qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530";
+};
+
+&pcie0 {
+       status = "okay";
+
+       perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+       wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+       bridge@0,0 {
+               reg = <0x00000000 0 0 0 0>;
+               #address-cells = <3>;
+               #size-cells = <2>;
+               ranges;
+
+               dsl@1,0 {
+                       compatible = "intel,vrx518";
+                       status = "okay";
+                       reg = <0x00010000 0 0 0 0>;
+               };
+       };
+};
index 22836be..3a7ecf3 100644 (file)
@@ -121,6 +121,15 @@ define Device/avm_fritzbox-4040
 endef
 TARGET_DEVICES += avm_fritzbox-4040
 
+define Device/avm_fritzbox-7530
+       $(call Device/FitImageLzma)
+       DEVICE_DTS := qcom-ipq4019-fritzbox-7530
+       DEVICE_TITLE := AVM Fritz!Box 7530
+       DEVICE_PACKAGES := fritz-caldata ipq-wifi-avm_fritzbox-7530
+       IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += avm_fritzbox-7530
+
 define Device/compex_wpj428
        $(call Device/FitImage)
        DEVICE_DTS := qcom-ipq4028-wpj428
index 5aeb396..89ce5b1 100644 (file)
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -697,7 +697,26 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -697,7 +697,27 @@ dtb-$(CONFIG_ARCH_QCOM) += \
        qcom-apq8074-dragonboard.dtb \
        qcom-apq8084-ifc6540.dtb \
        qcom-apq8084-mtp.dtb \
@@ -28,6 +28,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
        qcom-ipq4019-ap.dk01.1-c1.dtb \
 +      qcom-ipq4019-a62.dtb \
 +      qcom-ipq4019-ap.dk04.1-c1.dtb \
++      qcom-ipq4019-fritzbox-7530.dtb \
 +      qcom-ipq4019-map-ac2200.dtb \
 +      qcom-ipq4019-qxwlan-e2600ac-c1.dtb \
 +      qcom-ipq4019-qxwlan-e2600ac-c2.dtb \
index bceadc5..f47b7b6 100644 (file)
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -785,11 +785,29 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -785,11 +785,30 @@ dtb-$(CONFIG_ARCH_QCOM) += \
        qcom-apq8074-dragonboard.dtb \
        qcom-apq8084-ifc6540.dtb \
        qcom-apq8084-mtp.dtb \
@@ -31,6 +31,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
        qcom-ipq4019-ap.dk07.1-c1.dtb \
        qcom-ipq4019-ap.dk07.1-c2.dtb \
 +      qcom-ipq4019-a62.dtb \
++      qcom-ipq4019-fritzbox-7530.dtb \
 +      qcom-ipq4019-map-ac2200.dtb \
 +      qcom-ipq4019-qxwlan-e2600ac-c1.dtb \
 +      qcom-ipq4019-qxwlan-e2600ac-c2.dtb \