ath79: add support for Buffalo WHR-G301N
authorINAGAKI Hiroshi <musashino.open@gmail.com>
Tue, 14 Aug 2018 06:01:05 +0000 (15:01 +0900)
committerMathias Kresin <dev@kresin.me>
Thu, 16 Aug 2018 19:20:57 +0000 (21:20 +0200)
Buffalo WHR-G301N is a 2.4 GHz 11n router, based on Atheros AR7240.
Ported from ar71xx target.

Specification:

- Atheros AR7240
- 32 MB of RAM
- 4 MB of Flash
- 2.4 GHz 2T2R wifi
- 5x 10/100 Mbps Ethernet
- 9x LEDs, 4x keys
  - LED: 8x gpio-leds, 1x ath9k-leds
  - key: 2x buttons, 1x slide switch
- UART header on PCB
  - Vcc, GND, TX, RX from LEDs side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of WHR-G301N
2. Connect power cable to WHR-G301N and turn on it
3. Access to "http://192.168.11.1/" and open firmware update page
("ファーム更新")
4. Select the OpenWrt factory image and click execute ("実行") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[fix the SUPPORTED_DEVICES to be compatible with the ar71xx image]
Signed-off-by: Mathias Kresin <dev@kresin.me>
target/linux/ath79/base-files/etc/board.d/01_leds
target/linux/ath79/base-files/etc/board.d/02_network
target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
target/linux/ath79/dts/ar7240_buffalo_whr-g301n.dts [new file with mode: 0644]
target/linux/ath79/image/tiny.mk

index c3dc1bb..0d8222f 100755 (executable)
@@ -17,6 +17,13 @@ avm,fritz300e)
        ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "$boardname:green:rssi3" "wlan0" "60" "100"
        ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "$boardname:green:rssi4" "wlan0" "80" "100"
        ;;
+buffalo,whr-g301n)
+       ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth0"
+       ucidef_set_led_switch "lan1" "LAN1" "$boardname:green:lan1" "switch0" "0x02"
+       ucidef_set_led_switch "lan2" "LAN2" "$boardname:green:lan2" "switch0" "0x04"
+       ucidef_set_led_switch "lan3" "LAN3" "$boardname:green:lan3" "switch0" "0x08"
+       ucidef_set_led_switch "lan4" "LAN4" "$boardname:green:lan4" "switch0" "0x10"
+       ;;
 etactica,eg200)
        ucidef_set_led_netdev "lan" "LAN" "$boardname:red:eth0" "eth0"
        ucidef_set_led_oneshot "modbus" "Modbus" "$boardname:red:modbus" "100" "33"
index a29a295..5ff4b19 100755 (executable)
@@ -83,6 +83,7 @@ ath79_setup_interfaces()
                ucidef_add_switch "switch0" \
                        "0@eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6@eth0" "1:wan"
                ;;
+       buffalo,whr-g301n|\
        tplink,tl-mr3220-v1|\
        tplink,tl-mr3420-v1|\
        tplink,tl-wr841-v7)
index f71139c..1be0d2a 100644 (file)
@@ -111,6 +111,11 @@ case "$FIRMWARE" in
        avm,fritz300e)
                ath9k_eeprom_extract_reverse "urloader" 5441 1088
                ;;
+       buffalo,whr-g301n|\
+       tplink,tl-wr841-v5|\
+       tplink,tl-wr941-v4)
+               ath9k_eeprom_extract "art" 4096 3768
+               ;;
        ocedo,raccoon|\
        tplink,tl-wdr3600|\
        tplink,tl-wdr4300|\
@@ -131,10 +136,6 @@ case "$FIRMWARE" in
        ubnt,unifi)
                ath9k_eeprom_extract "art" 4096 2048
                ;;
-       tplink,tl-wr841-v5|\
-       tplink,tl-wr941-v4)
-               ath9k_eeprom_extract "art" 4096 3768
-               ;;
        *)
                ath9k_eeprom_die "board $board is not supported yet"
                ;;
diff --git a/target/linux/ath79/dts/ar7240_buffalo_whr-g301n.dts b/target/linux/ath79/dts/ar7240_buffalo_whr-g301n.dts
new file mode 100644 (file)
index 0000000..c00509b
--- /dev/null
@@ -0,0 +1,192 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar7240.dtsi"
+
+/ {
+       compatible = "buffalo,whr-g301n", "qca,ar7240";
+       model = "Buffalo WHR-G301N";
+
+       aliases {
+               led-boot = &diag;
+               led-failsafe = &diag;
+               led-upgrade = &diag;
+       };
+
+       gpio-keys-polled {
+               compatible = "gpio-keys-polled";
+               poll-interval = <20>;
+
+               router_on {
+                       label = "router_on";
+                       linux,code = <BTN_2>;
+                       linux,input-type = <EV_SW>;
+                       gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+                       debounce-interval = <60>;
+               };
+
+               router_off {
+                       label = "router_off";
+                       linux,code = <BTN_3>;
+                       linux,input-type = <EV_SW>;
+                       gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+                       debounce-interval = <60>;
+               };
+
+               reset {
+                       label = "reset";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+                       debounce-interval = <60>;
+               };
+
+               wps {
+                       label = "wps";
+                       linux,code = <KEY_WPS_BUTTON>;
+                       gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+                       debounce-interval = <60>;
+               };
+       };
+
+       gpio-leds {
+               compatible = "gpio-leds";
+               pinctrl-names = "default";
+               pinctrl-0 = <&switch_led_pins>;
+
+               security {
+                       label = "whr-g301n:orange:security";
+                       gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+               };
+
+               diag: diag {
+                       label = "whr-g301n:red:diag";
+                       gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+               };
+
+               router {
+                       label = "whr-g301n:green:router";
+                       gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+               };
+
+               lan1 {
+                       label = "whr-g301n:green:lan1";
+                       gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+               };
+
+               lan2 {
+                       label = "whr-g301n:green:lan2";
+                       gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+               };
+
+               lan3 {
+                       label = "whr-g301n:green:lan3";
+                       gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+               };
+
+               lan4 {
+                       label = "whr-g301n:green:lan4";
+                       gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+               };
+
+               wan {
+                       label = "whr-g301n:green:wan";
+                       gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       ath9k-leds {
+               compatible = "gpio-leds";
+
+               wlan {
+                       label = "whr-g301n:green:wlan";
+                       gpios = <&ath9k 1 GPIO_ACTIVE_LOW>;
+                       default-state = "off";
+                       linux,default-trigger = "phy0tpt";
+               };
+       };
+};
+
+&spi {
+       status = "okay";
+       num-cs = <1>;
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <25000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               reg = <0x0 0x3e000>;
+                               label = "u-boot";
+                               read-only;
+                       };
+
+                       partition@3e000 {
+                               reg = <0x3e000 0x2000>;
+                               label = "u-boot-env";
+                               read-only;
+                       };
+
+                       partition@40000 {
+                               reg = <0x40000 0x3a0000>;
+                               label = "firmware";
+                       };
+
+                       partition@3e0000 {
+                               reg = <0x3e0000 0x10000>;
+                               label = "user_property";
+                               read-only;
+                       };
+
+                       art: partition@3f0000 {
+                               reg = <0x3f0000 0x10000>;
+                               label = "art";
+                               read-only;
+                       };
+               };
+       };
+};
+
+&eth0 {
+       status = "okay";
+
+       mtd-mac-address = <&art 0x120c>;
+};
+
+&eth1 {
+       status = "okay";
+
+       mtd-mac-address = <&art 0x120c>;
+       mtd-mac-address-increment = <1>;
+};
+
+&pcie {
+       status = "okay";
+
+       ath9k: wifi@0,0 {
+               compatible = "pci168c,002a";
+               reg = <0x0000 0 0 0 0>;
+               qca,no-eeprom;
+               mtd-mac-address = <&art 0x120c>;
+               #gpio-cells = <2>;
+               gpio-controller;
+       };
+};
+
+&pinmux {
+       switch_led_pins: switch_led_pins {
+               pinctrl-single,bits = <0x0 0x0 0xf8>;
+       };
+};
+
+&uart {
+       status = "okay";
+};
index 0a14fcd..0047554 100644 (file)
@@ -1,5 +1,24 @@
 DEVICE_VARS += ROOTFS_SIZE
 
+define Build/buffalo-tftp-header
+       ( \
+               echo -n -e "# Airstation Public Fmt1" | dd bs=32 count=1 conv=sync; \
+               dd if=$@; \
+       ) > $@.new
+  mv $@.new $@
+endef
+
+define Build/buffalo-tag
+       $(eval product=$(word 1,$(1)))
+       $(STAGING_DIR_HOST)/bin/buffalo-tag \
+               -c 0x80041000 -d 0x801e8000 -w 3 \
+               -a ath -v 1.99 -m 1.01 -f 1 \
+               -b $(product) -p $(product) \
+               -r M_ -l mlang8 \
+               -i $@ -o $@.new
+       mv $@.new $@
+endef
+
 define Device/buffalo_bhr-4grv2
   ATH_SOC := qca9558
   DEVICE_TITLE := Buffalo BHR-4GRV2
@@ -16,3 +35,15 @@ define Device/buffalo_bhr-4grv2
   SUPPORTED_DEVICES += bhr-4grv2
 endef
 TARGET_DEVICES += buffalo_bhr-4grv2
+
+define Device/buffalo_whr-g301n
+  ATH_SOC := ar7240
+  DEVICE_TITLE := Buffalo WHR-G301N
+  IMAGE_SIZE := 3712k
+  IMAGES += factory.bin tftp.bin
+  IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE)
+  IMAGE/factory.bin := $$(IMAGE/default) | buffalo-enc WHR-G301N 1.99 | buffalo-tag WHR-G301N
+  IMAGE/tftp.bin := $$(IMAGE/default) | buffalo-tftp-header
+  SUPPORTED_DEVICES += whr-g301n
+endef
+TARGET_DEVICES += buffalo_whr-g301n