From: Piotr Dymacz Date: Mon, 18 Dec 2017 13:51:28 +0000 (+0100) Subject: ar71xx: add support for ALFA Network AP91-5G X-Git-Url: http://git.openwrt.org/?p=openwrt%2Fstaging%2Fwigyori.git;a=commitdiff_plain;h=7f9f42d42eff837d2eca5b4862cbb3b1ccebbefd ar71xx: add support for ALFA Network AP91-5G ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros AR7240 + AR9280. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 32 MB of RAM (DDR1) - 8 MB of FLASH (SPI NOR) - 1x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm - 6x LED (5 are driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, disabled and not used) - header for optional 802.3at/af PoE module - DC jack for main power input (optional, not installed by default) - UART and LEDs headers on PCB Flash instruction: Use "factory" image in vendor GUI (in case of problems, make sure your board has up to date firmware). Alternatively, TFTP in U-Boot can be used: select option "2. Load system code then write to Flash via TFTP" during early boot and use "sysupgrade" image. Signed-off-by: Piotr Dymacz --- diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds index e5baa90db8..97bf33052c 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds @@ -129,6 +129,14 @@ dr531) ;; esac ;; +ap91-5g) + ucidef_set_led_netdev "lan" "LAN" "$board:green:lan" "eth0" + ucidef_set_rssimon "wlan0" "200000" "1" + ucidef_set_led_rssi "signal1" "SIGNAL1" "$board:red:signal1" "wlan0" "1" "100" + ucidef_set_led_rssi "signal2" "SIGNAL2" "$board:orange:signal2" "wlan0" "25" "100" + ucidef_set_led_rssi "signal3" "SIGNAL3" "$board:green:signal3" "wlan0" "50" "100" + ucidef_set_led_rssi "signal4" "SIGNAL4" "$board:green:signal4" "wlan0" "75" "100" + ;; bhr-4grv2) ucidef_set_led_default "power" "POWER" "buffalo:green:power" "1" ucidef_set_led_default "diag" "DIAG" "buffalo:red:diag" "0" diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network index fb61792bf4..461b72f4d7 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/02_network +++ b/target/linux/ar71xx/base-files/etc/board.d/02_network @@ -64,6 +64,7 @@ ar71xx_setup_interfaces() antminer-s3|\ antrouter-r1|\ ap121f|\ + ap91-5g|\ aw-nr580|\ bullet-m|\ c-55|\ diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh index 6cbb3576d8..2f2d2c3103 100644 --- a/target/linux/ar71xx/base-files/etc/diag.sh +++ b/target/linux/ar71xx/base-files/etc/diag.sh @@ -80,6 +80,9 @@ get_status_led() { gl-mifi) status_led="$board:green:lan" ;; + ap91-5g) + status_led="$board:green:signal4" + ;; ap96) status_led="$board:green:led2" ;; diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh index b5440230a5..e90d89e20e 100755 --- a/target/linux/ar71xx/base-files/lib/ar71xx.sh +++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh @@ -446,6 +446,9 @@ ar71xx_board_detect() { *"AP90Q") name="ap90q" ;; + *"AP91-5G") + name="ap91-5g" + ;; *"Archer C25 v1") name="archer-c25-v1" ;; diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh index ecf6820a2b..37c637b6f5 100755 --- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh @@ -310,6 +310,7 @@ platform_check_image() { ap136-020|\ ap147-010|\ ap152|\ + ap91-5g|\ ap96|\ arduino-yun|\ bhr-4grv2|\ diff --git a/target/linux/ar71xx/config-4.4 b/target/linux/ar71xx/config-4.4 index 8478368062..44af80d0f3 100644 --- a/target/linux/ar71xx/config-4.4 +++ b/target/linux/ar71xx/config-4.4 @@ -49,6 +49,7 @@ CONFIG_ATH79=y # CONFIG_ATH79_MACH_AP531B0 is not set # CONFIG_ATH79_MACH_AP81 is not set # CONFIG_ATH79_MACH_AP90Q is not set +# CONFIG_ATH79_MACH_AP91_5G is not set # CONFIG_ATH79_MACH_AP96 is not set # CONFIG_ATH79_MACH_ARCHER_C25_V1 is not set # CONFIG_ATH79_MACH_ARCHER_C58_V1 is not set diff --git a/target/linux/ar71xx/config-4.9 b/target/linux/ar71xx/config-4.9 index 854c14a0f0..401c41e493 100644 --- a/target/linux/ar71xx/config-4.9 +++ b/target/linux/ar71xx/config-4.9 @@ -47,6 +47,7 @@ CONFIG_ATH79=y # CONFIG_ATH79_MACH_AP531B0 is not set # CONFIG_ATH79_MACH_AP81 is not set # CONFIG_ATH79_MACH_AP90Q is not set +# CONFIG_ATH79_MACH_AP91_5G is not set # CONFIG_ATH79_MACH_AP96 is not set # CONFIG_ATH79_MACH_ARCHER_C25_V1 is not set # CONFIG_ATH79_MACH_ARCHER_C58_V1 is not set diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt index 1198fcb74b..f2717e86e9 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt +++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt @@ -225,6 +225,15 @@ config ATH79_MACH_AP90Q select ATH79_DEV_M25P80 select ATH79_DEV_WMAC +config ATH79_MACH_AP91_5G + bool "ALFA Network AP91-5G support" + select SOC_AR724X + select ATH79_DEV_AP9X_PCI if PCI + select ATH79_DEV_ETH + select ATH79_DEV_GPIO_BUTTONS + select ATH79_DEV_LEDS_GPIO + select ATH79_DEV_M25P80 + config ATH79_MACH_AP96 bool "Atheros AP96 board support" select SOC_AR71XX diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile index 455af762e3..0e581005d7 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile +++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile @@ -57,6 +57,7 @@ obj-$(CONFIG_ATH79_MACH_AP147) += mach-ap147.o obj-$(CONFIG_ATH79_MACH_AP152) += mach-ap152.o obj-$(CONFIG_ATH79_MACH_AP531B0) += mach-ap531b0.o obj-$(CONFIG_ATH79_MACH_AP90Q) += mach-ap90q.o +obj-$(CONFIG_ATH79_MACH_AP91_5G) += mach-ap91-5g.o obj-$(CONFIG_ATH79_MACH_AP96) += mach-ap96.o obj-$(CONFIG_ATH79_MACH_ARCHER_C25_V1) += mach-archer-c25-v1.o obj-$(CONFIG_ATH79_MACH_ARCHER_C58_V1) += mach-archer-c59-v1.o diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-ap91-5g.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-ap91-5g.c new file mode 100644 index 0000000000..64b9430381 --- /dev/null +++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-ap91-5g.c @@ -0,0 +1,118 @@ +/* + * ALFA Network AP91-5G board support + * + * Copyright (C) 2018 Piotr Dymacz + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published + * by the Free Software Foundation. + */ + +#include +#include + +#include +#include + +#include "common.h" +#include "dev-ap9x-pci.h" +#include "dev-eth.h" +#include "dev-gpio-buttons.h" +#include "dev-leds-gpio.h" +#include "dev-m25p80.h" +#include "machtypes.h" + +#define AP91_5G_GPIO_LED_LAN 17 +#define AP91_5G_GPIO_LED_SIGNAL1 12 +#define AP91_5G_GPIO_LED_SIGNAL2 8 +#define AP91_5G_GPIO_LED_SIGNAL3 6 +#define AP91_5G_GPIO_LED_SIGNAL4 7 + +#define AP91_5G_GPIO_WDT_EN 1 +#define AP91_5G_GPIO_WDT_IN 0 + +#define AP91_5G_GPIO_BTN_RESET 11 + +#define AP91_5G_KEYS_POLL_INTERVAL 20 +#define AP91_5G_KEYS_DEBOUNCE_INTERVAL (3 * AP91_5G_KEYS_POLL_INTERVAL) + +#define AP91_5G_WMAC_CALDATA_OFFSET 0x1000 + +static struct gpio_led ap91_5g_leds_gpio[] __initdata = { + { + .name = "ap91-5g:green:lan", + .gpio = AP91_5G_GPIO_LED_LAN, + .active_low = 1, + }, { + .name = "ap91-5g:red:signal1", + .gpio = AP91_5G_GPIO_LED_SIGNAL1, + .active_low = 1, + }, { + .name = "ap91-5g:orange:signal2", + .gpio = AP91_5G_GPIO_LED_SIGNAL2, + .active_low = 1, + }, { + .name = "ap91-5g:green:signal3", + .gpio = AP91_5G_GPIO_LED_SIGNAL3, + .active_low = 1, + }, { + .name = "ap91-5g:green:signal4", + .gpio = AP91_5G_GPIO_LED_SIGNAL4, + .active_low = 1, + }, +}; + +static struct gpio_keys_button ap91_5g_gpio_keys[] __initdata = { + { + .desc = "reset", + .type = EV_KEY, + .code = KEY_RESTART, + .debounce_interval = AP91_5G_KEYS_DEBOUNCE_INTERVAL, + .gpio = AP91_5G_GPIO_BTN_RESET, + .active_low = 1, + }, +}; + +static void __init ap91_5g_setup(void) +{ + u8 *art = (u8 *) KSEG1ADDR(0x1fff0000); + + ath79_gpio_function_setup(AR724X_GPIO_FUNC_JTAG_DISABLE, + AR724X_GPIO_FUNC_ETH_SWITCH_LED4_EN); + + gpio_set_value(AP91_5G_GPIO_LED_LAN, 1); + gpio_set_value(AP91_5G_GPIO_LED_SIGNAL3, 1); + gpio_set_value(AP91_5G_GPIO_LED_SIGNAL4, 1); + + ath79_register_m25p80(NULL); + + ath79_register_mdio(0, 0x0); + + /* LAN */ + ath79_eth0_data.duplex = DUPLEX_FULL; + ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII; + ath79_eth0_data.phy_mask = BIT(4); + ath79_eth0_data.speed = SPEED_100; + ath79_init_mac(ath79_eth0_data.mac_addr, art, 0); + ath79_register_eth(0); + + ath79_register_leds_gpio(-1, ARRAY_SIZE(ap91_5g_leds_gpio), + ap91_5g_leds_gpio); + + ath79_register_gpio_keys_polled(-1, AP91_5G_KEYS_POLL_INTERVAL, + ARRAY_SIZE(ap91_5g_gpio_keys), + ap91_5g_gpio_keys); + + gpio_request_one(AP91_5G_GPIO_WDT_IN, + GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED, + "WDT input"); + + gpio_request_one(AP91_5G_GPIO_WDT_EN, + GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED, + "WDT enable"); + + ap91_pci_init(art + AP91_5G_WMAC_CALDATA_OFFSET, NULL); +} + +MIPS_MACHINE(ATH79_MACH_AP91_5G, "AP91-5G", "ALFA Network AP91-5G", + ap91_5g_setup); diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h index 0f536f0ec5..c2cb8b6126 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h +++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h @@ -41,6 +41,7 @@ enum ath79_mach_type { ATH79_MACH_AP152, /* Atheros AP152 reference board */ ATH79_MACH_AP531B0, /* Rockeetech AP531B0 */ ATH79_MACH_AP90Q, /* YunCore AP90Q */ + ATH79_MACH_AP91_5G, /* ALFA Network AP91-5G */ ATH79_MACH_AP96, /* Atheros AP96 */ ATH79_MACH_ARCHER_C25_V1, /* TP-LINK Archer C25 V1 board */ ATH79_MACH_ARCHER_C5, /* TP-LINK Archer C5 board */ diff --git a/target/linux/ar71xx/generic/config-default b/target/linux/ar71xx/generic/config-default index d5b59b5945..e9bf6f3267 100644 --- a/target/linux/ar71xx/generic/config-default +++ b/target/linux/ar71xx/generic/config-default @@ -25,6 +25,7 @@ CONFIG_ATH79_MACH_AP147=y CONFIG_ATH79_MACH_AP152=y CONFIG_ATH79_MACH_AP531B0=y CONFIG_ATH79_MACH_AP90Q=y +CONFIG_ATH79_MACH_AP91_5G=y CONFIG_ATH79_MACH_AP96=y CONFIG_ATH79_MACH_ARCHER_C25_V1=y CONFIG_ATH79_MACH_ARCHER_C58_V1=y diff --git a/target/linux/ar71xx/image/generic.mk b/target/linux/ar71xx/image/generic.mk index 89ab1f0291..d6515ac529 100644 --- a/target/linux/ar71xx/image/generic.mk +++ b/target/linux/ar71xx/image/generic.mk @@ -1,5 +1,12 @@ DEVICE_VARS += DAP_SIGNATURE NETGEAR_BOARD_ID NETGEAR_HW_ID NETGEAR_KERNEL_MAGIC ROOTFS_SIZE SEAMA_SIGNATURE +define Build/alfa-network-rootfs-header + mkimage \ + -A mips -O linux -T filesystem -C lzma -a 0 -e 0 \ + -n 'RootfsImage' -d $@ $@.new + @mv $@.new $@ +endef + define Build/mkbuffaloimg $(STAGING_DIR_HOST)/bin/mkbuffaloimg -B $(BOARDNAME) \ -R $$(($(subst k, * 1024,$(ROOTFS_SIZE)))) \ @@ -105,6 +112,22 @@ define Device/ap90q endef TARGET_DEVICES += ap90q +define Device/ap91-5g + DEVICE_TITLE := ALFA Network AP91-5G + DEVICE_PACKAGES := rssileds -swconfig + BOARDNAME := AP91-5G + IMAGE_SIZE := 7744k + KERNEL_SIZE := 1600k + ROOTFS_SIZE := 6144k + MTDPARTS := spi0.0:256k(u-boot)ro,64k(u-boot-env),6144k(rootfs),1600k(kernel),64k(config)ro,64k(art)ro,7744k@0x50000(firmware) + IMAGES := sysupgrade.bin factory.bin + IMAGE/factory.bin := append-rootfs | pad-rootfs |\ + alfa-network-rootfs-header | append-kernel | check-size $$$$(IMAGE_SIZE) + IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs |\ + pad-to $$$$(ROOTFS_SIZE) | append-kernel | check-size $$$$(IMAGE_SIZE) +endef +TARGET_DEVICES += ap91-5g + define Device/arduino-yun DEVICE_TITLE := Arduino Yun DEVICE_PACKAGES := kmod-usb-core kmod-usb2