target/linux/kirkwood/patches-4.4/180-goflexhome.patch

   1 --- a/arch/arm/boot/dts/Makefile
   2 +++ b/arch/arm/boot/dts/Makefile
   3 @@ -175,6 +175,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
   4         kirkwood-ds411.dtb \
   5         kirkwood-ds411j.dtb \
   6         kirkwood-ds411slim.dtb \
   7 +       kirkwood-goflexhome.dtb \
   8         kirkwood-goflexnet.dtb \
   9         kirkwood-guruplug-server-plus.dtb \
  10         kirkwood-ib62x0.dtb \
  11 --- /dev/null
  12 +++ b/arch/arm/boot/dts/kirkwood-goflexhome.dts
  13 @@ -0,0 +1,117 @@
  14 +/dts-v1/;
  15 +
  16 +#include "kirkwood.dtsi"
  17 +#include "kirkwood-6281.dtsi"
  18 +
  19 +/ {
  20 +       model = "Seagate GoFlex Home";
  21 +       compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
  22 +
  23 +       memory {
  24 +               device_type = "memory";
  25 +               reg = <0x00000000 0x8000000>;
  26 +       };
  27 +
  28 +       chosen {
  29 +               bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
  30 +               stdout-path = &uart0;
  31 +       };
  32 +
  33 +       ocp@f1000000 {
  34 +               pinctrl: pin-controller@10000 {
  35 +                       pmx_usb_power_enable: pmx-usb-power-enable {
  36 +                               marvell,pins = "mpp29";
  37 +                               marvell,function = "gpio";
  38 +                       };
  39 +                       pmx_led_white: pmx-led-white {
  40 +                               marvell,pins = "mpp40";
  41 +                               marvell,function = "gpio";
  42 +                       };
  43 +                       pmx_led_green: pmx-led_green {
  44 +                               marvell,pins = "mpp46";
  45 +                               marvell,function = "gpio";
  46 +                       };
  47 +                       pmx_led_orange: pmx-led-orange {
  48 +                               marvell,pins = "mpp47";
  49 +                               marvell,function = "gpio";
  50 +                       };
  51 +               };
  52 +               serial@12000 {
  53 +                       status = "ok";
  54 +               };
  55 +
  56 +               sata@80000 {
  57 +                       status = "okay";
  58 +                       nr-ports = <2>;
  59 +               };
  60 +
  61 +       };
  62 +       gpio-leds {
  63 +               compatible = "gpio-leds";
  64 +
  65 +               health {
  66 +                       label = "status:green:health";
  67 +                       gpios = <&gpio1 14 1>;
  68 +                       linux,default-trigger = "default-on";
  69 +               };
  70 +               fault {
  71 +                       label = "status:orange:fault";
  72 +                       gpios = <&gpio1 15 1>;
  73 +               };
  74 +               misc {
  75 +                       label = "status:white:misc";
  76 +                       gpios = <&gpio1 8 1>;
  77 +                       linux,default-trigger = "ide-disk";
  78 +               };
  79 +       };
  80 +       regulators {
  81 +               compatible = "simple-bus";
  82 +               #address-cells = <1>;
  83 +               #size-cells = <0>;
  84 +               pinctrl-0 = <&pmx_usb_power_enable>;
  85 +               pinctrl-names = "default";
  86 +
  87 +               usb_power: regulator@1 {
  88 +                       compatible = "regulator-fixed";
  89 +                       reg = <1>;
  90 +                       regulator-name = "USB Power";
  91 +                       regulator-min-microvolt = <5000000>;
  92 +                       regulator-max-microvolt = <5000000>;
  93 +                       enable-active-high;
  94 +                       regulator-always-on;
  95 +                       regulator-boot-on;
  96 +                       gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
  97 +               };
  98 +       };
  99 +};
 100 +
 101 +&nand {
 102 +       chip-delay = <40>;
 103 +       status = "okay";
 104 +
 105 +       partition@0 {
 106 +               label = "u-boot";
 107 +               reg = <0x0000000 0x100000>;
 108 +               read-only;
 109 +       };
 110 +
 111 +       partition@100000 {
 112 +               label = "ubi";
 113 +               reg = <0x100000 0x0ff00000>;
 114 +       };
 115 +};
 116 +
 117 +&mdio {
 118 +       status = "okay";
 119 +
 120 +       ethphy0: ethernet-phy@0 {
 121 +               reg = <0>;
 122 +       };
 123 +};
 124 +
 125 +&eth0 {
 126 +       status = "okay";
 127 +       ethernet0-port@0 {
 128 +               phy-handle = <&ethphy0>;
 129 +       };
 130 +};