ramips: Change all '/include/' clauses to '#include' so preprocessing can be done...
[openwrt/svn-archive/archive.git] / target / linux / ramips / dts / MZK-W300NH2.dts
1 /dts-v1/;
2
3 #include "rt3050.dtsi"
4
5 / {
6 compatible = "MZK-W300NH2", "ralink,rt3052-soc";
7 model = "Planex MZK-W300NH2";
8
9 pinctrl {
10 state_default: pinctrl0 {
11 gpio {
12 ralink,group = "spi", "i2c", "jtag", "rgmii", "mdio", "uartf";
13 ralink,function = "gpio";
14 };
15 };
16 };
17
18 cfi@1f000000 {
19 compatible = "cfi-flash";
20 reg = <0x1f000000 0x800000>;
21 bank-width = <2>;
22 device-width = <2>;
23 #address-cells = <1>;
24 #size-cells = <1>;
25
26 partition@0 {
27 label = "u-boot";
28 reg = <0x0 0x30000>;
29 read-only;
30 };
31
32 partition@30000 {
33 label = "u-boot-env";
34 reg = <0x30000 0x10000>;
35 read-only;
36 };
37
38 factory: partition@40000 {
39 label = "factory";
40 reg = <0x40000 0x10000>;
41 read-only;
42 };
43
44 partition@3e0000 {
45 label = "cimage";
46 reg = <0x3e0000 0x20000>;
47 read-only;
48 };
49
50 partition@50000 {
51 label = "firmware";
52 reg = <0x50000 0x390000>;
53 };
54 };
55
56 ethernet@10100000 {
57 mtd-mac-address = <&factory 0x4>;
58 };
59
60 esw@10110000 {
61 mediatek,portmap = <0x2f>;
62 };
63
64 wmac@10180000 {
65 ralink,mtd-eeprom = <&factory 0>;
66 };
67
68 gpio-leds {
69 compatible = "gpio-leds";
70
71 power {
72 label = "mzk-w300nh2:green:power";
73 gpios = <&gpio0 9 1>;
74 };
75
76 wlan {
77 label = "mzk-w300nh2:amber:wlan";
78 gpios = <&gpio0 14 1>;
79 };
80
81 wps {
82 label = "mzk-w300nh2:amber:wps";
83 gpios = <&gpio0 11 1>;
84 };
85 };
86
87 gpio-keys-polled {
88 compatible = "gpio-keys-polled";
89 #address-cells = <1>;
90 #size-cells = <0>;
91 poll-interval = <20>;
92
93 wps {
94 label = "wps";
95 gpios = <&gpio0 12 1>;
96 linux,code = <0x211>;
97 };
98
99 reset {
100 label = "reset";
101 gpios = <&gpio0 0 1>;
102 linux,code = <0x198>;
103 };
104
105 rt {
106 label = "rt";
107 gpios = <&gpio0 13 1>;
108 linux,code = <0x100>;
109 };
110 };
111 };