ralink: add pinctrl driver
[openwrt/svn-archive/archive.git] / target / linux / ramips / dts / WL-351.dts
1 /dts-v1/;
2
3 /include/ "rt3050.dtsi"
4
5 / {
6 compatible = "WL-351", "ralink,rt3052-soc";
7 model = "Sitecom WL-351 v1 002";
8
9 pinctrl {
10 state_default: pinctrl0 {
11 gpio {
12 ralink,group = "spi", "i2c", "jtag", "rgmii", "mdio", "uartf";
13 ralink,function = "gpio";
14 };
15 };
16 };
17
18 cfi@1f000000 {
19 compatible = "cfi-flash";
20 reg = <0x1f000000 0x800000>;
21
22 bank-width = <2>;
23 device-width = <2>;
24 #address-cells = <1>;
25 #size-cells = <1>;
26
27 partition@0 {
28 label = "u-boot";
29 reg = <0x0 0x30000>;
30 read-only;
31 };
32
33 partition@30000 {
34 label = "u-boot-env";
35 reg = <0x30000 0x10000>;
36 read-only;
37 };
38
39 factory: partition@40000 {
40 label = "factory";
41 reg = <0x40000 0x10000>;
42 read-only;
43 };
44
45 partition@50000 {
46 label = "firmware";
47 reg = <0x50000 0x3b0000>;
48 };
49 };
50
51 esw@10110000 {
52 ralink,portmap = <0x3f>;
53 ralink,fct2 = <0x0002500c>;
54 /*
55 * ext phy base addr 31, rx/tx clock skew 0,
56 * turbo mii off, rgmi 3.3v off, port 5 polling off
57 * port5: enabled, gige, full-duplex, rx/tx-flow-control
58 * port6: enabled, gige, full-duplex, rx/tx-flow-control
59 */
60 ralink,fpa2 = <0x1f003fff>;
61 };
62
63 otg@101c0000 {
64 status = "okay";
65 };
66
67 gpio-leds {
68 compatible = "gpio-leds";
69 power {
70 label = "wl-351:amber:power";
71 gpios = <&gpio0 8 1>;
72 };
73 unpopulated {
74 label = "wl-351:amber:unpopulated";
75 gpios = <&gpio0 12 1>;
76 };
77 unpopulated2 {
78 label = "wl-351:blue:unpopulated";
79 gpios = <&gpio0 13 1>;
80 };
81 };
82
83 gpio-keys-polled {
84 compatible = "gpio-keys-polled";
85 #address-cells = <1>;
86 #size-cells = <0>;
87 poll-interval = <20>;
88 reset {
89 label = "reset";
90 gpios = <&gpio0 10 1>;
91 linux,code = <0x198>;
92 };
93 wps {
94 label = "wps";
95 gpios = <&gpio0 0 1>;
96 linux,code = <0x211>;
97 };
98 };
99
100 rtl8366rb {
101 compatible = "rtl8367rb";
102 gpio-sda = <&gpio0 1 0>;
103 gpio-sck = <&gpio0 2 0>;
104 };
105 };