# Kismet drone config file version=Feb.04.01a # Name of server (Purely for organiational purposes) servername=Kismet # User to setid to (should be your normal user) suiduser=your_user_here # Port to serve packet data... This probably shouldn't be the same as the port # you configured kismet_server for, or else you'll have problems running them # on the same system. tcpport=3501 # People allowed to connect, comma seperated IP addresses or network/mask # blocks. Netmasks can be expressed as dotted quad (/255.255.255.0) or as # numbers (/24) allowedhosts=127.0.0.1 # Maximum number of concurrent stream attachments maxclients=5 # Packet sources: # source=capture_cardtype,capture_interface,capture_name # Card type - Specifies the type of device. It can be one of: # cisco - Cisco card with Linux Kernel drivers # cisco_cvs - Cisco card with CVS Linux drivers # cisco_bsd - Cisco on *BSD # prism2 - Prism2 using wlan-ng drivers with pcap support (all # current versions support pcap) # prism2_hostap - Prism2 using hostap drivers # prism2_legacy - Prism2 using wlan-ng drivers without pcap support (0.1.9) # prism2_bsd - Prism2 on *BSD # orinoco - Orinoco cards using Snax's patched driers # generic - Generic card with no specific support. You will have # to put this into monitor mode yourself! # wsp100 - WSP100 embedded remote sensor. # wtapfile - Saved file of packets readable by libwiretap # ar5k - ar5k 802.11a using the vt_ar5k drivers # Capture interface - Specifies the network interface Kismet will watch for # packets to come in on. Typically "ethX" or "wlanX". For the WSP100 capture # engine, the WSP100 device sends packets via a UDP stream, so the capture # interface should be in the form of host:port where 'host' is the WSP100 and # 'port' is the local UDP port that it will send data to. # Capture Name - The name Kismet uses for this capture source. This is the # name used to specify what sources to enable. # # To enable multiple sources, specify a source line for each and then use the # enablesources line to enable them. For example: # source=prism2,wlan0,prism # source=cisco,eth0,cisco source=generic,prism0,Kismet-Drone # Comma-separated list of sources to enable. This is only needed if you wish # to selectively enable multiple sources. # enablesources=prism,cisco # Do we channelhop? channelhop=true # How many channels per second do we hop? (1-10) channelvelocity=5 # By setting the dwell time for channel hopping we override the channelvelocity # setting above and dwell on each channel for the given number of seconds. #channeldwell=10 # Do we split channels between cards on the same spectrum? This means if # multiple 802.11b capture sources are defined, they will be offset to cover # the most possible spectrum at a given time. This also controls splitting # fine-tuned sourcechannels lines which cover multiple interfaces (see below) splitchannels=true # Basic channel hopping control: # These define the channels the cards hop through for various frequency ranges # supported by Kismet. More finegrain control is available via the # "sourcechannels" configuration option. # # Don't change the IEEE80211 identifiers or channel hopping won't work. # Users outside the US might want to use this list: # defaultchannels=IEEE80211b:1,7,13,2,8,3,14,9,4,10,5,11,6,12 defaultchannels=IEEE80211b:1,6,11,2,7,3,8,4,9,5,10 # 802.11g uses the same channels as 802.11b... defaultchannels=IEEE80211g:1,6,11,2,7,3,8,4,9,5,10 # 802.11a channels are non-overlapping so sequential is fine. You may want to # adjust the list depending on the channels your card actually supports. # defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64,100,104,108,112,116,120,124,128,132,136,140,149,153,157,161,184,188,192,196,200,204,208,212,216 defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64 # Combo cards like Atheros use both 'a' and 'b/g' channels. Of course, you # can also explicitly override a given source. You can use the script # extras/listchan.pl to extract all the channels your card supports. defaultchannels=IEEE80211ab:1,6,11,2,7,3,8,4,9,5,10,36,40,44,48,52,56,60,64 # Fine-tuning channel hopping control: # The sourcechannels option can be used to set the channel hopping for # specific interfaces, and to control what interfaces share a list of # channels for split hopping. This can also be used to easily lock # one card on a single channel while hopping with other cards. # Any card without a sourcechannel definition will use the standard hopping # list. # sourcechannels=sourcename[,sourcename]:ch1,ch2,ch3,...chN # ie, for us channels on the source 'prism2source' (same as normal channel # hopping behavior): # sourcechannels=prism2source:1,6,11,2,7,3,8,4,9,5,10 # Given two capture sources, "prism2a" and "prism2b", we want prism2a to stay # on channel 6 and prism2b to hop normally. By not setting a sourcechannels # line for prism2b, it will use the standard hopping. # sourcechannels=prism2a:6 # To assign the same custom hop channel to multiple sources, or to split the # same custom hop channel over two sources (if splitchannels is true), list # them all on the same sourcechannels line: # sourcechannels=prism2a,prism2b,prism2c:1,6,11