WRTSL54GS,
WRT54G3G,
WRT54G3GV2_VF,
- WRT160N,
+ WRT150NV1,
+ WRT150NV11,
+ WRT160NV1,
+ WRT160NV3,
WRT300NV11,
WRT350N,
WRT600N,
WRT600NV11,
WRT610N,
+ WRT610NV2,
+ E3000V1,
/* ASUS */
WLHDD,
WL520GU,
ASUS_4702,
WL700GE,
+ RTN16,
/* Buffalo */
WBR2_G54,
/* Belkin */
BELKIN_UNKNOWN,
+ BELKIN_F7D4301,
/* Netgear */
WGT634U,
/* Enables GPIO 3 that controls HDD and led power on ASUS WL-700gE */
printk(MODULE_NAME ": Spinning up HDD and enabling leds\n");
- ssb_gpio_outen(&ssb_bcm47xx, pin, pin);
- ssb_gpio_control(&ssb_bcm47xx, pin, 0);
- ssb_gpio_out(&ssb_bcm47xx, pin, pin);
+ gpio_outen(pin, pin);
+ gpio_control(pin, 0);
+ gpio_out(pin, pin);
/* Wait 5s, so the HDD can spin up */
set_current_state(TASK_INTERRUPTIBLE);
static void __init NetCenter_init(void) {
/* unset pin 6 (+12V) */
int pin = 1 << 6;
- ssb_gpio_outen(&ssb_bcm47xx, pin, pin);
- ssb_gpio_control(&ssb_bcm47xx, pin, 0);
- ssb_gpio_out(&ssb_bcm47xx, pin, pin);
+ gpio_outen(pin, pin);
+ gpio_control(pin, 0);
+ gpio_out(pin, pin);
/* unset pin 1 (turn off red led, blue will light alone if +5V comes up) */
pin = 1 << 1;
- ssb_gpio_outen(&ssb_bcm47xx, pin, pin);
- ssb_gpio_control(&ssb_bcm47xx, pin, 0);
- ssb_gpio_out(&ssb_bcm47xx, pin, pin);
+ gpio_outen(pin, pin);
+ gpio_control(pin, 0);
+ gpio_out(pin, pin);
/* unset pin 3 (+5V) and wait 5 seconds (harddisk spin up) */
bcm4780_init();
}
int pin = 1 << 2;
/* FIXME: switch comes up, but port mappings/vlans not right */
- ssb_gpio_outen(&ssb_bcm47xx, pin, pin);
- ssb_gpio_control(&ssb_bcm47xx, pin, 0);
- ssb_gpio_out(&ssb_bcm47xx, pin, pin);
+ gpio_outen(pin, pin);
+ gpio_control(pin, 0);
+ gpio_out(pin, pin);
}
static struct platform_t __initdata platforms[] = {
{ .name = "3g_blue", .gpio = 1 << 3, .polarity = NORMAL },
},
},
- [WRT160N] = {
- .name = "Linksys WRT160N",
+ [WRT150NV1] = {
+ .name = "Linksys WRT150N V1",
+ .buttons = {
+ { .name = "reset", .gpio = 1 << 6 },
+ { .name = "ses", .gpio = 1 << 4 },
+ },
+ .leds = {
+ { .name = "power", .gpio = 1 << 1, .polarity = NORMAL },
+ { .name = "ses_green", .gpio = 1 << 5, .polarity = REVERSE },
+ { .name = "ses_amber", .gpio = 1 << 3, .polarity = REVERSE },
+ },
+ },
+ [WRT150NV11] = {
+ .name = "Linksys WRT150N V1.1",
+ .buttons = {
+ { .name = "reset", .gpio = 1 << 6 },
+ { .name = "ses", .gpio = 1 << 4 },
+ },
+ .leds = {
+ { .name = "power", .gpio = 1 << 1, .polarity = NORMAL },
+ { .name = "ses_green", .gpio = 1 << 5, .polarity = REVERSE },
+ { .name = "ses_amber", .gpio = 1 << 3, .polarity = REVERSE },
+ },
+ },
+ [WRT160NV1] = {
+ .name = "Linksys WRT160N v1.x",
.buttons = {
{ .name = "reset", .gpio = 1 << 6 },
{ .name = "ses", .gpio = 1 << 4 },
{ .name = "ses_orange", .gpio = 1 << 3, .polarity = REVERSE },
},
},
+ [WRT160NV3] = {
+ .name = "Linksys WRT160N V3",
+ .buttons = {
+ { .name = "reset", .gpio = 1 << 6 },
+ { .name = "ses", .gpio = 1 << 5 },
+ },
+ .leds = {
+ { .name = "power", .gpio = 1 << 1, .polarity = NORMAL },
+ { .name = "ses_blue", .gpio = 1 << 4, .polarity = REVERSE },
+ { .name = "ses_orange", .gpio = 1 << 2, .polarity = REVERSE },
+ },
+ },
[WRT300NV11] = {
.name = "Linksys WRT300N V1.1",
.buttons = {
{ .name = "ses_blue", .gpio = 1 << 9, .polarity = REVERSE }, // WiFi protected setup LED blue
},
},
+ [WRT610NV2] = {
+ .name = "Linksys WRT610N V2",
+ .buttons = {
+ { .name = "reset", .gpio = 1 << 6 },
+ { .name = "ses", .gpio = 1 << 4 },
+ },
+ .leds = {
+ { .name = "power", .gpio = 1 << 5, .polarity = NORMAL }, // Power LED
+ { .name = "usb", .gpio = 1 << 7, .polarity = NORMAL }, // USB LED
+ { .name = "ses_amber", .gpio = 1 << 0, .polarity = REVERSE }, // WiFi protected setup LED amber
+ { .name = "ses_blue", .gpio = 1 << 3, .polarity = REVERSE }, // WiFi protected setup LED blue
+ { .name = "wlan", .gpio = 1 << 1, .polarity = NORMAL }, // Wireless LED
+ },
+ },
+ [E3000V1] = {
+ .name = "Linksys E3000 V1",
+ .buttons = {
+ { .name = "reset", .gpio = 1 << 6 },
+ { .name = "ses", .gpio = 1 << 4 },
+ },
+ .leds = {
+ { .name = "power", .gpio = 1 << 5, .polarity = NORMAL }, // Power LED
+ { .name = "usb", .gpio = 1 << 7, .polarity = NORMAL }, // USB LED
+ { .name = "ses_amber", .gpio = 1 << 0, .polarity = REVERSE }, // WiFi protected setup LED amber
+ { .name = "ses_blue", .gpio = 1 << 3, .polarity = REVERSE }, // WiFi protected setup LED blue
+ { .name = "wlan", .gpio = 1 << 1, .polarity = NORMAL }, // Wireless LED
+ },
+ },
/* Asus */
[WLHDD] = {
.name = "ASUS WL-HDD",
},
.platform_init = bcm4780_init,
},
+ [RTN16] = {
+ .name = "ASUS RT-N16",
+ .buttons = {
+ { .name = "reset", .gpio = 1 << 8 },
+ { .name = "ses", .gpio = 1 << 5 },
+ },
+ .leds = {
+ { .name = "power", .gpio = 1 << 1, .polarity = REVERSE },
+ { .name = "wlan", .gpio = 1 << 7, .polarity = NORMAL },
+ },
+ },
/* Buffalo */
[WHR_G54S] = {
.name = "Buffalo WHR-G54S",
{ .name = "connected", .gpio = 1 << 0, .polarity = NORMAL },
},
},
+ [BELKIN_F7D4301] = {
+ .name = "Belkin PlayMax F7D4301",
+ .buttons = {
+ { .name = "reset", .gpio = 1 << 6 },
+ { .name = "wps", .gpio = 1 << 8 },
+ },
+ .leds = {
+ { .name = "power", .gpio = 1 << 11, .polarity = REVERSE },
+ { .name = "wlan", .gpio = 1 << 13, .polarity = REVERSE },
+ { .name = "led0", .gpio = 1 << 14, .polarity = REVERSE },
+ { .name = "led1", .gpio = 1 << 15, .polarity = REVERSE },
+ },
+ },
/* Netgear */
[WGT634U] = {
.name = "Netgear WGT634U",
return &platforms[WL520GU];
if (startswith(buf,"WL330GE-")) /* WL330GE-* */
return &platforms[WL330GE];
+ if (startswith(buf,"RT-N16-")) /* RT-N16-* */
+ return &platforms[RTN16];
+ if (startswith(buf,"F7D4301")) /* F7D4301* */
+ return &platforms[BELKIN_F7D4301];
}
/* Based on "ModelId" */
return &platforms[WRT600N];
}
+ /*
+ * Normally, these would go inside the "CFE based - newer hardware" block below; however, during early init, the
+ * "pmon_ver" variable is not available on the E3000v1 (and probably the WRT610Nv2 also). Until this is figured out,
+ * these will need to remain here in order for platform detection to work.
+ */
+ if (!strcmp(boardnum, "42")) { /* Linksys */
+ if (!strcmp(boardtype, "0x04cf") && !strcmp(getvar("boot_hw_model"), "E300") && !strcmp(getvar("boot_hw_ver"), "1.0"))
+ return &platforms[E3000V1];
+
+ if (!strcmp(boardtype, "0x04cf") && !strcmp(getvar("boot_hw_model"), "WRT610N") && !strcmp(getvar("boot_hw_ver"), "2.0"))
+ return &platforms[WRT610NV2];
+ }
+
if (startswith(getvar("pmon_ver"), "CFE")) {
/* CFE based - newer hardware */
if (!strcmp(boardnum, "42")) { /* Linksys */
if (!strcmp(getvar("et1phyaddr"),"5") && !strcmp(getvar("et1mdcport"), "1"))
return &platforms[WRTSL54GS];
- if (!strcmp(boardtype, "0x0472"))
- return &platforms[WRT160N];
+ if (!strcmp(boardtype, "0x0472")) {
+ if(!strcmp(getvar("boot_hw_model"), "WRT150N"))
+ if(!strcmp(getvar("boot_hw_ver"), "1"))
+ return &platforms[WRT150NV1];
+ else if(!strcmp(getvar("boot_hw_ver"), "1.1"))
+ return &platforms[WRT150NV11];
+ else if(!strcmp(getvar("boot_hw_model"), "WRT160N"))
+ if(!strcmp(getvar("boot_hw_ver"), "1.0"))
+ return &platforms[WRT160NV1];
+ else if(!strcmp(getvar("boot_hw_ver"), "3.0"))
+ return &platforms[WRT160NV3];
+ }
/* default to WRT54G */
return &platforms[WRT54G];
platform.button_mask &= ~gpiomask;
- ssb_gpio_outen(&ssb_bcm47xx, platform.button_mask, 0);
- ssb_gpio_control(&ssb_bcm47xx, platform.button_mask, 0);
- platform.button_polarity = ssb_gpio_in(&ssb_bcm47xx, ~0) & platform.button_mask;
- ssb_gpio_polarity(&ssb_bcm47xx, platform.button_mask, platform.button_polarity);
- ssb_gpio_intmask(&ssb_bcm47xx, platform.button_mask, platform.button_mask);
+ gpio_outen(platform.button_mask, 0);
+ gpio_control(platform.button_mask, 0);
+ platform.button_polarity = gpio_in() & platform.button_mask;
+ gpio_intpolarity(platform.button_mask, platform.button_polarity);
+ gpio_setintmask(platform.button_mask, platform.button_mask);
gpio_set_irqenable(1, button_handler);
}
static void unregister_buttons(struct button_t *b)
{
- ssb_gpio_intmask(&ssb_bcm47xx, platform.button_mask, 0);
+ gpio_setintmask(platform.button_mask, 0);
gpio_set_irqenable(0, button_handler);
}
struct button_t *b;
u32 in, changed;
- in = ssb_gpio_in(&ssb_bcm47xx, ~0) & platform.button_mask;
- ssb_gpio_polarity(&ssb_bcm47xx, platform.button_mask, in);
+ in = gpio_in() & platform.button_mask;
+ gpio_intpolarity(platform.button_mask, in);
changed = platform.button_polarity ^ in;
platform.button_polarity = in;
- changed &= ~ssb_gpio_outen(&ssb_bcm47xx, 0, 0);
+ changed &= ~gpio_outen(0, 0);
for (b = platform.buttons; b->name; b++) {
struct event_t *event;
}
}
- ssb_gpio_outen(&ssb_bcm47xx, mask, oe_mask);
- ssb_gpio_control(&ssb_bcm47xx, mask, 0);
- ssb_gpio_out(&ssb_bcm47xx, mask, val);
- ssb_gpio_intmask(&ssb_bcm47xx, mask, 0);
+ gpio_outen(mask, oe_mask);
+ gpio_control(mask, 0);
+ gpio_out(mask, val);
+ gpio_setintmask(mask, 0);
}
static void unregister_leds(struct led_t *l)
mask &= ~gpiomask;
if (mask) {
- u32 val = ~ssb_gpio_in(&ssb_bcm47xx, ~0);
+ u32 val = ~gpio_in();
- ssb_gpio_outen(&ssb_bcm47xx, mask, mask);
- ssb_gpio_control(&ssb_bcm47xx, mask, 0);
- ssb_gpio_out(&ssb_bcm47xx, mask, val);
+ gpio_outen(mask, mask);
+ gpio_control(mask, 0);
+ gpio_out(mask, val);
}
if (mask || extif_blink) {
mod_timer(&led_timer, jiffies + FLASH_TIME);
if (led->gpio & GPIO_TYPE_EXTIF) {
len = sprintf(page, "%d\n", led->state);
} else {
- u32 in = (ssb_gpio_in(&ssb_bcm47xx, ~0) & led->gpio ? 1 : 0);
+ u32 in = (gpio_in() & led->gpio ? 1 : 0);
u8 p = (led->polarity == NORMAL ? 0 : 1);
len = sprintf(page, "%d\n", ((in ^ p) ? 1 : 0));
}
led->state = p ^ ((page[0] == '1') ? 1 : 0);
set_led_extif(led);
} else {
- ssb_gpio_outen(&ssb_bcm47xx, led->gpio, led->gpio);
- ssb_gpio_control(&ssb_bcm47xx, led->gpio, 0);
- ssb_gpio_out(&ssb_bcm47xx, led->gpio, ((p ^ (page[0] == '1')) ? led->gpio : 0));
+ gpio_outen(led->gpio, led->gpio);
+ gpio_control(led->gpio, 0);
+ gpio_out(led->gpio, ((p ^ (page[0] == '1')) ? led->gpio : 0));
}
}
break;
static struct proc_dir_entry *p;
static struct platform_t *detected;
-#ifdef CONFIG_BCM47XX_SSB
- if (bcm47xx_active_bus_type != BCM47XX_BUS_TYPE_SSB) {
- printk(MODULE_NAME ": bcma bus is not supported.\n");
- return -ENODEV;
- }
-#endif
-
detected = platform_detect();
if (!detected) {
printk(MODULE_NAME ": Router model not detected.\n");
projects / openwrt / svn-archive / archive.git / blobdiff