SERVICE_DAEMONIZE=1
SERVICE_WRITE_PID=1
-#
-# Basic functions to send CLI commands to the vdsl_cpe_control daemon
-#
-dsl_cmd() {
- killall -0 vdsl_cpe_control && (
- echo "$@" > /tmp/pipe/dsl_cpe0_cmd
- cat /tmp/pipe/dsl_cpe0_ack
- )
-}
-dsl_val() {
- echo $(expr "$1" : '.*'$2'=\([-\.[:alnum:]]*\).*')
+. /lib/functions/lantiq_dsl.sh
+XDSL_CTRL=vdsl_cpe_control
+
+# G.992.1 Annex A
+# G.992.2 Annex A
+# G.992.3 Annex A
+# G.992.4 Annex A
+# G.992.5 Annex A
+# G.993.2 Annex A/B/C
+xtse_adsl_a="04 01 04 01 00 01 00 00"
+
+# G.992.1 Annex B
+# G.992.3 Annex B
+# G.992.5 Annex B
+# G.993.2 Annex A/B/C
+xtse_adsl_b="10 00 10 00 00 04 00 00"
+
+# G.992.1 Annex B
+# G.992.3 Annex B
+# G.992.3 Annex J
+# G.992.5 Annex B
+# G.992.5 Annex J
+# G.993.2 Annex A/B/C
+xtse_adsl_j="10 00 10 40 00 04 01 00"
+
+xtse_vdsl="00 00 00 00 00 00 00 07"
+
+xdsl_scr() {
+ val=`echo $2 | sed "s/ / 0x/g"`
+ echo "[WaitForConfiguration]={
+#G997XTUSEC_g997xtusecs 0x$val
}
-#
-# Simple divide by 10 routine to cope with one decimal place
-#
-dbt() {
- local a=$(expr $1 / 10)
- local b=$(expr $1 % 10)
- echo "${a}.${b}"
-}
-#
-# Take a number and convert to k or meg
-#
-scale() {
- local val=$1
- local a
- local b
-
- if [ "$val" -gt 1000000 ]; then
- a=$(expr $val / 1000)
- b=$(expr $a % 1000)
- a=$(expr $a / 1000)
- printf "%d.%03d Mb" ${a} ${b}
- elif [ "$val" -gt 1000 ]; then
- a=$(expr $val / 1000)
- printf "%d Kb" ${a}
- else
- echo "${val} b"
- fi
+[WaitForLinkActivate]={
}
-#
-# Read the data rates for both directions
-#
-data_rates() {
- local csg
- local dru
- local drd
- local sdru
- local sdrd
-
- csg=$(dsl_cmd g997csg 0 1)
- drd=$(dsl_val "$csg" ActualDataRate)
-
- csg=$(dsl_cmd g997csg 0 0)
- dru=$(dsl_val "$csg" ActualDataRate)
-
- [ -z "$drd" ] && drd=0
- [ -z "$dru" ] && dru=0
-
- sdrd=$(scale $drd)
- sdru=$(scale $dru)
-
- if [ "$action" = "lucistat" ]; then
- echo "dsl.data_rate_down=$drd"
- echo "dsl.data_rate_up=$dru"
- echo "dsl.data_rate_down_s=\"$sdrd\""
- echo "dsl.data_rate_up_s=\"$sdru\""
- else
- echo "Data Rate: ${sdrd}/s / ${sdru}/s"
- fi
+[WaitForRestart]={
}
-#
-# Chipset
-#
-chipset() {
- local vig
- local cs
- local csv
-
- vig=$(dsl_cmd vig)
- cs=$(dsl_val "$vig" DSL_ChipSetType)
- csv=$(dsl_val "$vig" DSL_ChipSetHWVersion)
-
- if [ "$action" = "lucistat" ]; then
- echo "dsl.chipset=\"${cs} ${csv}\""
- else
- echo "Chipset: ${cs} ${csv}"
- fi
+[Common]={
+}" > /tmp/$1.scr
}
+# A43
+tone_adsl_a="0x142"
+tone_vdsl_a="0x142"
+
+# A43 + V43
+tone_adsl_av="0x142"
+tone_vdsl_av="0x146"
+
+# B43
+tone_adsl_b="0x1"
+tone_vdsl_b="0x1"
+
+# B43 + V43
+tone_adsl_bv="0x1"
+tone_vdsl_bv="0x5"
+
+lowlevel_cfg() {
+ echo "# VRX Low Level Configuration File
#
-# Work out how long the line has been up
+# Parameters must be separated by tabs or spaces.
+# Empty lines and comments will be ignored.
#
-line_uptime() {
- local ccsg
- local et
- local etr
- local d
- local h
- local m
- local s
- local rc=""
-
- ccsg=$(dsl_cmd pmccsg 0 0 0)
- et=$(dsl_val "$ccsg" nElapsedTime)
-
- [ -z "$et" ] && et=0
-
- if [ "$action" = "lucistat" ]; then
- echo "dsl.line_uptime=${et}"
- return
- fi
-
- d=$(expr $et / 86400)
- etr=$(expr $et % 86400)
- h=$(expr $etr / 3600)
- etr=$(expr $etr % 3600)
- m=$(expr $etr / 60)
- s=$(expr $etr % 60)
-
-
- [ "${d}${h}${m}${s}" -ne 0 ] && rc="${s}s"
- [ "${d}${h}${m}" -ne 0 ] && rc="${m}m ${rc}"
- [ "${d}${h}" -ne 0 ] && rc="${h}h ${rc}"
- [ "${d}" -ne 0 ] && rc="${d}d ${rc}"
-
- [ -z "$rc" ] && rc="down"
- echo "Line Uptime: ${rc}"
-}
+# nFilter
#
-# Get noise and attenuation figures
+# NA = -1
+# OFF = 0
+# ISDN = 1
+# POTS = 2
+# POTS_2 = 3
+# POTS_3 = 4
#
-line_data() {
- local lsg
- local latnu
- local latnd
- local snru
- local snrd
-
- lsg=$(dsl_cmd g997lsg 1 1)
- latnd=$(dsl_val "$lsg" LATN)
- snrd=$(dsl_val "$lsg" SNR)
-
- lsg=$(dsl_cmd g997lsg 0 1)
- latnu=$(dsl_val "$lsg" LATN)
- snru=$(dsl_val "$lsg" SNR)
-
- [ -z "$latnd" ] && latnd=0
- [ -z "$latnu" ] && latnu=0
- [ -z "$snrd" ] && snrd=0
- [ -z "$snru" ] && snru=0
-
- latnd=$(dbt $latnd)
- latnu=$(dbt $latnu)
- snrd=$(dbt $snrd)
- snru=$(dbt $snru)
-
- if [ "$action" = "lucistat" ]; then
- echo "dsl.line_attenuation_down=$latnd"
- echo "dsl.line_attenuation_up=$latnu"
- echo "dsl.noise_margin_down=$snrd"
- echo "dsl.noise_margin_up=$snru"
- else
- echo "Line Attenuation: ${latnd}dB / ${latnu}dB"
- echo "Noise Margin: ${snrd}dB / ${snru}dB"
- fi
-}
+# (dec)
+ -1
+# nHsToneGroupMode nHsToneGroup_A nHsToneGroup_V nHsToneGroup_AV
#
-# Is the line up? Or what state is it in?
+# NA = -1 NA = -1 see see
+# AUTO = 0 VDSL2_B43 = 0x0001 nHsToneGroup_A nHsToneGroup_A
+# MANUAL = 1 VDSL2_A43 = 0x0002
+# VDSL2_V43 = 0x0004
+# VDSL1_V43P = 0x0008
+# VDSL1_V43I = 0x0010
+# ADSL1_C43 = 0x0020
+# ADSL2_J43 = 0x0040
+# ADSL2_B43C = 0x0080
+# ADSL2_A43C = 0x0100
#
-line_state() {
- local lsg=$(dsl_cmd lsg)
- local ls=$(dsl_val "$lsg" nLineState);
- local s;
-
- case "$ls" in
- "0x0") s="not initialized" ;;
- "0x1") s="exception" ;;
- "0x10") s="not updated" ;;
- "0xff") s="idle request" ;;
- "0x100") s="idle" ;;
- "0x1ff") s="silent request" ;;
- "0x200") s="silent" ;;
- "0x300") s="handshake" ;;
- "0x380") s="full_init" ;;
- "0x400") s="discovery" ;;
- "0x500") s="training" ;;
- "0x600") s="analysis" ;;
- "0x700") s="exchange" ;;
- "0x800") s="showtime_no_sync" ;;
- "0x801") s="showtime_tc_sync" ;;
- "0x900") s="fastretrain" ;;
- "0xa00") s="lowpower_l2" ;;
- "0xb00") s="loopdiagnostic active" ;;
- "0xb10") s="loopdiagnostic data exchange" ;;
- "0xb20") s="loopdiagnostic data request" ;;
- "0xc00") s="loopdiagnostic complete" ;;
- "0x1000000") s="test" ;;
- "0xd00") s="resync" ;;
- "0x3c0") s="short init entry" ;;
- "") s="not running daemon"; ls="0xfff" ;;
- *) s="unknown" ;;
- esac
+# (dec) (hex) (hex) (hex)
+ 1 $1 $2 0x0
- if [ $action = "lucistat" ]; then
- echo "dsl.line_state_num=$ls"
- echo "dsl.line_state_detail=\"$s\""
- if [ "$ls" = "0x801" ]; then
- echo "dsl.line_state=\"UP\""
- else
- echo "dsl.line_state=\"DOWN\""
- fi
- else
- if [ "$ls" = "0x801" ]; then
- echo "Line State: UP [$ls: $s]"
- else
- echo "Line State: DOWN [$ls: $s]"
- fi
- fi
-}
+# nBaseAddr nIrqNum
+#
+# (hex) (dec)
+ 0x1e116000 63
+# nUtopiaPhyAdr nUtopiaBusWidth nPosPhyParity
+# default(16b) = 0 NA = -1
+# 8-bit = 1 ODD = 0
+# 16-bit = 2
#
-# Main status routine
#
-status() {
- chipset
- line_state
- data_rates
- line_data
- line_uptime
-}
+# (hex) (dec) (dec)
+ 0xFF 0 0
+# bNtrEnable
#
-# Luci (lua) compatible version that's easy to parse
-#
-lucistat() {
- echo "local dsl={}"
- status
- echo "return dsl"
+# (dec)
+ 0" > /tmp/lowlevel.cfg
}
-
-annex_b=10_00_10_00_00_04_00_00
-annex_bdmt=10_00_00_00_00_00_00_00
-annex_b2=00_00_10_00_00_00_00_00
-annex_b2p=00_00_00_00_00_04_00_00
-annex_a=04_01_04_00_00_01_00_00
-annex_at1=01_00_00_00_00_00_00_00
-annex_alite=00_01_00_00_00_00_00_00
-annex_admt=04_00_00_00_00_00_00_00
-annex_a2=00_00_04_00_00_00_00_00
-annex_a2p=00_00_00_00_00_01_00_00
-annex_l=00_00_00_00_04_00_00_00
-annex_m=00_00_00_00_40_00_04_00
-annex_m2=00_00_00_00_40_00_00_00
-annex_m2p=00_00_00_00_00_00_04_00
-
-#
-# Simple start routine
-#
start() {
local annex
local firmware
- local xtu
+ local tone
+ local tone_adsl
+ local tone_vdsl
+ local xtse_adsl
+ local mode
+
config_load network
+ config_get tone wan tone
config_get annex wan annex
config_get firmware wan firmware
+ config_get xfer_mode wan xfer_mode
+
+ [ -z "${xfer_mode}" ] && xfer_mode=ptm
+
+ case "${xfer_mode}" in
+ atm)
+ insmod ltq_atm_vr9
+ mode=1
+ ;;
+ *)
+ insmod ltq_ptm_vr9
+ mode=2
+ ;;
+ esac
+
+ eval "xtse_adsl=\"\${xtse_adsl_$annex}\""
+ [ -z "${xtse_adsl}" ] && xtse_adsl=$xtse_adsl_b
- # get xtu
- eval "xtu=\"\${annex_$annex}\""
+ eval "tone_adsl=\"\${tone_adsl_$tone}\""
+ [ -z "${tone_adsl}" ] && tone_adsl=$tone_adsl_av
- # check for firmware
- [ -z "${firmware}" ] &&
- firmware=vdsl.bin
+ eval "tone_vdsl=\"\${tone_vdsl_$tone}\""
+ [ -z "${tone_vdsl}" ] && tone_vdsl=$tone_vdsl_av
+
+ [ -z "${firmware}" ] && firmware=vdsl.bin
- # start CPE dsl daemon in the background
- service_start /sbin/vdsl_cpe_control -i${xtu} \
+ xdsl_scr adsl "${xtse_adsl}"
+ xdsl_scr vdsl "${xtse_vdsl}"
+ lowlevel_cfg "${tone_adsl}" "${tone_vdsl}"
+
+ service_start /sbin/vdsl_cpe_control \
+ -i `echo $xtse_adsl | sed "s/ /_/g"` \
-n /sbin/dsl_notify.sh \
- -f /lib/firmware/${firmware}
+ -f /lib/firmware/${firmware} \
+ -a /tmp/adsl.scr \
+ -A /tmp/vdsl.scr \
+ -l /tmp/lowlevel.cfg \
+ -M ${mode}
}
-#
-# For stop we want to simulate the notification call for when
-# the line goes down, so that we can stop the ppp link before
-# we die.
-#
stop() {
DSL_NOTIFICATION_TYPE="DSL_INTERFACE_STATUS" \
DSL_INTERFACE_STATUS="DOWN" \
service_stop /sbin/vdsl_cpe_control
}
-
projects / openwrt / svn-archive / archive.git / blobdiff