/*
* Planex MZK-W300NH board support
*
- * Copyright (C) 2008 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2008-2009 Gabor Juhos <juhosg@openwrt.org>
* Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
*
* This program is free software; you can redistribute it and/or modify it
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/flash.h>
+#include <linux/input.h>
#include <asm/mips_machine.h>
#include <asm/mach-ar71xx/ar71xx.h>
-#include <asm/mach-ar71xx/platform.h>
+
+#include "devices.h"
+#include "dev-m25p80.h"
+#include "dev-ar913x-wmac.h"
+
+#define MZK_W300NH_GPIO_LED_STATUS 1
+#define MZK_W300NH_GPIO_LED_WPS 3
+#define MZK_W300NH_GPIO_LED_WLAN 6
+#define MZK_W300NH_GPIO_LED_AP 15
+#define MZK_W300NH_GPIO_LED_ROUTER 16
+
+#define MZK_W300NH_GPIO_BTN_APROUTER 5
+#define MZK_W300NH_GPIO_BTN_WPS 12
+#define MZK_W300NH_GPIO_BTN_RESET 21
+
+#define MZK_W04NU_BUTTONS_POLL_INTERVAL 20
#ifdef CONFIG_MTD_PARTITIONS
static struct mtd_partition mzk_w300nh_partitions[] = {
.offset = 0x040000,
.size = 0x010000,
} , {
- .name = "uImage",
+ .name = "kernel",
.offset = 0x050000,
.size = 0x160000,
} , {
.offset = 0x7e0000,
.size = 0x020000,
.mask_flags = MTD_WRITEABLE,
+ } , {
+ .name = "firmware",
+ .offset = 0x050000,
+ .size = 0x770000,
}
};
#endif /* CONFIG_MTD_PARTITIONS */
#endif
};
-static struct spi_board_info mzk_w300nh_spi_info[] = {
+static struct gpio_led mzk_w300nh_leds_gpio[] __initdata = {
{
- .bus_num = 0,
- .chip_select = 0,
- .max_speed_hz = 25000000,
- .modalias = "m25p80",
- .platform_data = &mzk_w300nh_flash_data,
+ .name = "mzk-w300nh:green:status",
+ .gpio = MZK_W300NH_GPIO_LED_STATUS,
+ .active_low = 1,
+ }, {
+ .name = "mzk-w300nh:blue:wps",
+ .gpio = MZK_W300NH_GPIO_LED_WPS,
+ .active_low = 1,
+ }, {
+ .name = "mzk-w300nh:green:wlan",
+ .gpio = MZK_W300NH_GPIO_LED_WLAN,
+ .active_low = 1,
+ }, {
+ .name = "mzk-w300nh:green:ap",
+ .gpio = MZK_W300NH_GPIO_LED_AP,
+ .active_low = 1,
+ }, {
+ .name = "mzk-w300nh:green:router",
+ .gpio = MZK_W300NH_GPIO_LED_ROUTER,
+ .active_low = 1,
+ }
+};
+
+static struct gpio_button mzk_w300nh_gpio_buttons[] __initdata = {
+ {
+ .desc = "reset",
+ .type = EV_KEY,
+ .code = BTN_0,
+ .threshold = 5,
+ .gpio = MZK_W300NH_GPIO_BTN_RESET,
+ .active_low = 1,
+ }, {
+ .desc = "wps",
+ .type = EV_KEY,
+ .code = BTN_1,
+ .threshold = 5,
+ .gpio = MZK_W300NH_GPIO_BTN_WPS,
+ .active_low = 1,
+ }, {
+ .desc = "aprouter",
+ .type = EV_KEY,
+ .code = BTN_2,
+ .threshold = 5,
+ .gpio = MZK_W300NH_GPIO_BTN_APROUTER,
+ .active_low = 0,
}
};
static void __init mzk_w300nh_setup(void)
{
- ar71xx_add_device_spi(NULL, mzk_w300nh_spi_info,
- ARRAY_SIZE(mzk_w300nh_spi_info));
+ u8 *mac = (u8 *) KSEG1ADDR(0x1fff1000);
+
+ ar71xx_set_mac_base(mac);
+
+ ar71xx_add_device_mdio(0x0);
+
+ ar71xx_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RMII;
+ ar71xx_eth0_data.phy_mask = 0xf;
+ ar71xx_eth0_data.speed = SPEED_100;
+ ar71xx_eth0_data.duplex = DUPLEX_FULL;
+ ar71xx_eth0_data.has_ar8216 = 1;
+
+ ar71xx_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_RMII;
+ ar71xx_eth1_data.phy_mask = 0x10;
+
+ ar71xx_add_device_eth(0);
+ ar71xx_add_device_eth(1);
+
+ ar71xx_add_device_m25p80(&mzk_w300nh_flash_data);
+
+ ar71xx_add_device_leds_gpio(-1, ARRAY_SIZE(mzk_w300nh_leds_gpio),
+ mzk_w300nh_leds_gpio);
- ar91xx_add_device_wmac();
+ ar71xx_add_device_gpio_buttons(-1, MZK_W04NU_BUTTONS_POLL_INTERVAL,
+ ARRAY_SIZE(mzk_w300nh_gpio_buttons),
+ mzk_w300nh_gpio_buttons);
+ ar913x_add_device_wmac();
}
MIPS_MACHINE(AR71XX_MACH_MZK_W300NH, "Planex MZK-W300NH", mzk_w300nh_setup);