+obj-$(CONFIG_ATHEROS_AR2315) += ar2315.o
--- /dev/null
+++ b/arch/mips/ar231x/board.c
-@@ -0,0 +1,259 @@
+@@ -0,0 +1,260 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ }
+
+ if (!found) {
-+ printk("Could not find Radio Configuration data\n");
++ pr_warn("WARNING: Could not find Radio Configuration data\n");
+ radio_config = 0;
+ }
+
+ }
+
+ if (!bcfg) {
-+ printk(KERN_WARNING "WARNING: No board configuration data found!\n");
++ pr_warn("WARNING: No board configuration data found!\n");
+ return -ENODEV;
+ }
+
+ ar231x_board.config = (struct ar231x_boarddata *) board_data;
+ memcpy(board_data, bcfg, 0x100);
+ if (broken_boarddata) {
-+ printk(KERN_WARNING "WARNING: broken board data detected\n");
++ pr_warn("WARNING: broken board data detected\n");
+ config = ar231x_board.config;
+ if (!memcmp(config->enet0_mac, "\x00\x00\x00\x00\x00\x00", 6)) {
-+ printk(KERN_INFO "Fixing up empty mac addresses\n");
++ pr_info("Fixing up empty mac addresses\n");
+ config->reset_config_gpio = 0xffff;
+ config->sys_led_gpio = 0xffff;
+ random_ether_addr(config->wlan0_mac);
+ radio_data = board_data + 0x100 + ((rcfg - bcfg) & 0xfff);
+ ar231x_board.radio = radio_data;
+ offset = radio_data - board_data;
-+ printk(KERN_INFO "Radio config found at offset 0x%x(0x%x)\n", rcfg - bcfg, offset);
++ pr_info("Radio config found at offset 0x%x (0x%x)\n", rcfg - bcfg,
++ offset);
+ rcfg_size = BOARD_CONFIG_BUFSZ - offset;
+ memcpy(radio_data, rcfg, rcfg_size);
+
+ mac_addr = &radio_data[0x1d * 2];
+ if (is_broadcast_ether_addr(mac_addr)) {
-+ printk(KERN_INFO "Radio MAC is blank; using board-data\n");
++ pr_info("Radio MAC is blank; using board-data\n");
+ memcpy(mac_addr, ar231x_board.config->wlan0_mac, ETH_ALEN);
+ }
+
+ u32 dma1 = ar231x_read_reg(AR531X_DMA1);
+ u32 dma_addr = ar231x_read_reg(AR531X_DMAADDR); /* clears error */
+
-+ printk("AHB interrupt: PROCADDR=0x%8.8x PROC1=0x%8.8x DMAADDR=0x%8.8x DMA1=0x%8.8x\n",
-+ proc_addr, proc1, dma_addr, dma1);
++ pr_emerg("AHB interrupt: PROCADDR=0x%8.8x PROC1=0x%8.8x "
++ "DMAADDR=0x%8.8x DMA1=0x%8.8x\n", proc_addr, proc1, dma_addr,
++ dma1);
+
+ machine_restart("AHB error"); /* Catastrophic failure */
+ return IRQ_HANDLED;
+ gpch = &ar5312_gpio_chip;
+ ret = gpiochip_add(&gpch->chip);
+ if (ret) {
-+ printk(KERN_ERR "%s: failed to add gpiochip\n",
-+ gpch->chip.label);
++ pr_err("%s: failed to add gpiochip\n", gpch->chip.label);
+ return ret;
+ }
-+ printk(KERN_INFO "%s: registered %d GPIOs\n",
-+ gpch->chip.label, gpch->chip.ngpio);
++ pr_info("%s: registered %d GPIOs\n", gpch->chip.label,
++ gpch->chip.ngpio);
+ return ret;
+}
+
+
--- /dev/null
+++ b/arch/mips/ar231x/ar2315.c
-@@ -0,0 +1,692 @@
+@@ -0,0 +1,691 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ ar231x_write_reg(AR2315_AHB_ERR0, AHB_ERROR_DET);
+ ar231x_read_reg(AR2315_AHB_ERR1);
+
-+ printk(KERN_ERR "AHB fatal error\n");
++ pr_emerg("AHB fatal error\n");
+ machine_restart("AHB error"); /* Catastrophic failure */
+
+ return IRQ_HANDLED;
+ gpch = &ar2315_gpio_chip;
+ ret = gpiochip_add(&gpch->chip);
+ if (ret) {
-+ printk(KERN_ERR "%s: failed to add gpiochip\n",
-+ gpch->chip.label);
++ pr_err("%s: failed to add gpiochip\n", gpch->chip.label);
+ return ret;
+ }
-+ printk(KERN_INFO "%s: registered %d GPIOs\n",
-+ gpch->chip.label, gpch->chip.ngpio);
++ pr_info("%s: registered %d GPIOs\n", gpch->chip.label,
++ gpch->chip.ngpio);
+ return ret;
+}
+