[ramips] add Ralink V11ST-FE board support

[openwrt/svn-archive/archive.git] / target / linux / ramips / base-files / etc / hotplug.d / firmware / 10-rt2x00-eeprom

diff --git a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
index 03ff4f81d4c2688c5b9824ec6ba61a7ba4f48edb..5e6fa420d77d13639c7bad671cadf2b45d7652e1 100644 (file)
--- a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
+++ b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom
@@ -23,13 +23,13 @@ rt2x00_eeprom_extract() {
 
 [ -e /lib/firmware/$FIRMWARE ] && exit 0
 
+. /lib/ramips.sh
+
+board=$(ramips_board_name)
+
 case "$FIRMWARE" in
 "RT288X.eeprom" | \
 "RT305X.eeprom")
-       . /lib/ramips.sh
-
-       local board=$(ramips_board_name)
-
        case $board in
        dir-300-b1 | \
        dir-600-b1 | \
@@ -37,21 +37,54 @@ case "$FIRMWARE" in
                rt2x00_eeprom_extract "devdata" 16384 272
                ;;
 
-       f5d8235v2 | \
+       rt-g32-b1)
+               rt2x00_eeprom_extract "devconf" 0 272
+               ;;
+
+       f5d8235-v1 | \
+       f5d8235-v2)
+               rt2x00_eeprom_extract "u-boot" 262144 272
+               ;;
+
+       all0256n | \
+       argus-atp52b | \
+       bc2 | \
+       esr-9753 | \
        fonera20n | \
        hw550-3g | \
        mofi3500-3gn | \
        pwh2004 | \
+       nbg-419n | \
+       nw718 | \
+       omni-emb | \
        rt-n15 | \
+       v11st-fe | \
        v22rw-2x2 | \
-       wcr150gn | \
-       whr-g300n)
+       w502u | \
+       wcr-150gn | \
+       whr-g300n | \
+       wl-351 | \
+       wli-tx4-ag300n | \
+       wr512-3gn | \
+       wr6202)
                rt2x00_eeprom_extract "factory" 0 272
                ;;
 
+       wl341v3)
+               rt2x00_eeprom_extract "board-nvram" 64880 272
+               ;;
+
        *)
                rt2x00_eeprom_die "board $board is not supported yet"
                ;;
        esac
        ;;
-esac
\ No newline at end of file
+
+"rt2x00pci_1_0.eeprom")
+       case $board in
+       rt-n56u)
+               rt2x00_eeprom_extract "factory" 32768 272
+               ;;
+       esac
+       ;;
+esac