generic: Fix per interface nf_call_iptables setting
authorFelix Fietkau <nbd@openwrt.org>
Wed, 9 Sep 2015 18:40:15 +0000 (18:40 +0000)
committerFelix Fietkau <nbd@openwrt.org>
Wed, 9 Sep 2015 18:40:15 +0000 (18:40 +0000)
commit26b4472758d485471e111931c4b9de23684a1b12
tree9b7b73c06bb3d697d0edfd72ca4efcb5a39ad207
parenta6e86a4a7883fbbf8641a0bd28c17b3f5ef2f9f7
generic: Fix per interface nf_call_iptables setting

commit r30917 ("kernel: bypass all netfilter hooks if the sysctls for that
functionality have been disabled - eliminates the overhead of enabling
CONFIG_BRIDGE_NETFILTER in the kernel config") introduced an optimization
which should reduce/eliminate the overhead for traffic send over bridges on
kernels compiled with CONFIG_BRIDGE_NETFILTER=y. But this optimization
breaks the nf_call_iptables per bridge setting which is more fine grained
than the global sysctl net.bridge.bridge-nf-call-iptables setting.

A test reflecting a real world setup was created to identify if this really
eliminates the overhead and if per-bridge nf_call_iptables could be used in
some setups to increase the throughput. A Qualcomm Atheros QCA9558 based
system with one ethernet and an ath9k wifi 3x3 in HT40 mode was used.
Cables from the AP to the wifi station were used to reduce interference
problems during the tests.

The wlan interface was put in one bridge interface called br-wlan. This
bridge usually contains some more wlan interfaces. The eth0 was put in a
second bridge called br-lan. This usually contains some other privileged
wlan or mesh interfaces. Routing was added between br-lan and br-wlan.

Three kernels were tested:

 * (default) OpenWrt kernel for this device
 * (brfilter-global) OpenWrt kernel with CONFIG_BRIDGE_NETFILTER=y
 * (brfilter-local)  OpenWrt kernel with CONFIG_BRIDGE_NETFILTER=y and
    without 644-bridge_optimize_netfilter_hooks.patch

The changes to the the netfilter settings of the bridge were done via:

 * (brfilter-global) /sbin/sysctl -w net.bridge.bridge-nf-call-iptables=1
 * (brfilter-lobal) echo 1 > /sys/class/net/br-lan/bridge/nf_call_iptables
   and/or echo 1 > /sys/class/net/br-wan/bridge/nf_call_iptables

A station connected to the wlan0 (AP) interface was used to send traffic to
a PC connected via ethernet. iperf with 3 concurrent transmissions was used
to generate the traffic.

| kernel          | br-nf-* global | nf-call* iface | download | upload   |
|-----------------|----------------|----------------|----------|----------|
| default         | 0              | -              |      209 |      268 |
| brfilter-global | 0              | -              |      185 |      243 |
| brfilter-local  | 0              | -              |      187 |      243 |
| brfilter-local  | 0              | br-lan         |      157 |      226 |
| brfilter-local  | 0              | br-lan br-wlan |      139 |      161 |
| brfilter-global | 1              | -              |      136 |      162 |

Download/upload results in Mibit/s

It can be seen that the patch doesn't eliminate the overhead. It can also
be seen that the throughput of brfilter-global and brfilter-local with
disabled filtering is the roughly the same. Also the throughput for
brfilter-global and brfilter-local for enabled filtering on all bridges is
roughly the same.

But also the brfilter-local throughput is higher when only br-lan requires
the filtering. This setting would not be possible with
644-bridge_optimize_netfilter_hooks.patch applied and thus can only be
compared with brfilter-global and filtering enabled for all interfaces.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46835
target/linux/generic/patches-3.18/644-bridge_optimize_netfilter_hooks.patch [deleted file]
target/linux/generic/patches-4.0/644-bridge_optimize_netfilter_hooks.patch [deleted file]
target/linux/generic/patches-4.1/644-bridge_optimize_netfilter_hooks.patch [deleted file]