[adm5120] prepare for 2.6.23
authorGabor Juhos <juhosg@openwrt.org>
Thu, 11 Oct 2007 07:45:02 +0000 (07:45 +0000)
committerGabor Juhos <juhosg@openwrt.org>
Thu, 11 Oct 2007 07:45:02 +0000 (07:45 +0000)
SVN-Revision: 9258

16 files changed:
target/linux/adm5120/patches-2.6.23/001-adm5120.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.23/002-adm5120_flash.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.23/003-adm5120_switch.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.23/004-adm5120_nand.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.23/005-adm5120_usb.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.23/006-adm5120_leds.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.23/007-adm5120_pci.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.23/008-adm5120_uart.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.23/100-mtd_myloder_partition_parser.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.23/101-cfi_fixup_macronix_bootloc.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.23/102-jedec_pmc_39lvxxx_chips.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.23/103-mtd_trxsplit.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.23/140-cmdline_hack.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.23/200-amba_pl010_hacks.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.23/201-amba_bus_hacks.patch [new file with mode: 0644]
target/linux/adm5120/patches-2.6.23/300-i2c_gpio_custom.patch [new file with mode: 0644]

diff --git a/target/linux/adm5120/patches-2.6.23/001-adm5120.patch b/target/linux/adm5120/patches-2.6.23/001-adm5120.patch
new file mode 100644 (file)
index 0000000..b197b3f
--- /dev/null
@@ -0,0 +1,115 @@
+Index: linux-2.6.23/arch/mips/Kconfig
+===================================================================
+--- linux-2.6.23.orig/arch/mips/Kconfig
++++ linux-2.6.23/arch/mips/Kconfig
+@@ -15,6 +15,18 @@ choice
+       prompt "System type"
+       default SGI_IP22
++config MIPS_ADM5120
++      bool "ADM5120 SoC based machines"
++      select SYS_HAS_CPU_MIPS32_R1
++      select SYS_HAS_EARLY_PRINTK
++      select DMA_NONCOHERENT
++      select HW_HAS_PCI
++      select IRQ_CPU
++      select SYS_SUPPORTS_LITTLE_ENDIAN
++      select SYS_SUPPORTS_BIG_ENDIAN
++      select SYS_SUPPORTS_32BIT_KERNEL
++      select GENERIC_GPIO
++
+ config MACH_ALCHEMY
+       bool "Alchemy processor based machines"
+@@ -597,6 +609,7 @@ config WR_PPMC
+ endchoice
++source "arch/mips/adm5120/Kconfig"
+ source "arch/mips/au1000/Kconfig"
+ source "arch/mips/jazz/Kconfig"
+ source "arch/mips/pmc-sierra/Kconfig"
+Index: linux-2.6.23/arch/mips/Makefile
+===================================================================
+--- linux-2.6.23.orig/arch/mips/Makefile
++++ linux-2.6.23/arch/mips/Makefile
+@@ -168,6 +168,16 @@ cflags-$(CONFIG_MACH_JAZZ)        += -Iinclude/
+ load-$(CONFIG_MACH_JAZZ)      += 0xffffffff80080000
+ #
++# ADMtek 5120
++#
++
++libs-$(CONFIG_MIPS_ADM5120)   += arch/mips/adm5120/prom/
++core-$(CONFIG_MIPS_ADM5120)   += arch/mips/adm5120/
++core-$(CONFIG_MIPS_ADM5120)   += arch/mips/adm5120/boards/
++cflags-$(CONFIG_MIPS_ADM5120) += -Iinclude/asm-mips/mach-adm5120
++load-$(CONFIG_MIPS_ADM5120)   += 0xffffffff80001000
++
++#
+ # Common Alchemy Au1x00 stuff
+ #
+ core-$(CONFIG_SOC_AU1X00)     += arch/mips/au1000/common/
+Index: linux-2.6.23/include/asm-mips/bootinfo.h
+===================================================================
+--- linux-2.6.23.orig/include/asm-mips/bootinfo.h
++++ linux-2.6.23/include/asm-mips/bootinfo.h
+@@ -208,6 +208,58 @@
+ #define MACH_GROUP_WINDRIVER   28     /* Windriver boards */
+ #define MACH_WRPPMC             1
++/*
++ * Valid machtype for group ADMtek ADM5120
++ */
++#define MACH_GROUP_ADM5120    26
++#define MACH_ADM5120_GENERIC  0       /* Generic board */
++#define MACH_ADM5120_WP54G_WRT        1       /* Compex WP54G-WRT */
++#define MACH_ADM5120_WP54G    2       /* Compex WP54G */
++#define MACH_ADM5120_WP54AG   3       /* Compex WP54AG */
++#define MACH_ADM5120_WPP54G   4       /* Compex WPP54G */
++#define MACH_ADM5120_WPP54AG  5       /* Compex WPP54AG */
++#define MACH_ADM5120_NP28G    6       /* Compex NP28G */
++#define MACH_ADM5120_NP28GHS  7       /* Compex NP28G HotSpot */
++#define MACH_ADM5120_NP27G    8       /* Compex NP27G */
++#define MACH_ADM5120_WP54Gv1C 9       /* Compex WP54G version 1C */
++#define MACH_ADM5120_RB_111   10      /* Mikrotik RouterBOARD 111 */
++#define MACH_ADM5120_RB_112   11      /* Mikrotik RouterBOARD 112 */
++#define MACH_ADM5120_RB_133   12      /* Mikrotik RouterBOARD 133 */
++#define MACH_ADM5120_RB_133C  13      /* Mikrotik RouterBOARD 133c */
++#define MACH_ADM5120_RB_150   14      /* Mikrotik RouterBOARD 150 */
++#define MACH_ADM5120_RB_153   15      /* Mikrotik RouterBOARD 153 */
++#define MACH_ADM5120_HS100    16      /* ZyXEL HomeSafe 100/100W */
++#define MACH_ADM5120_P334     17      /* ZyXEL Prestige 334 */
++#define MACH_ADM5120_P334U    18      /* ZyXEL Prestige 334U */
++#define MACH_ADM5120_P334W    19      /* ZyXEL Prestige 334W */
++#define MACH_ADM5120_P334WH   20      /* ZyXEL Prestige 334WH */
++#define MACH_ADM5120_P334WHD  21      /* ZyXEL Prestige 334WHD */
++#define MACH_ADM5120_P334WT   22      /* ZyXEL Prestige 334WT */
++#define MACH_ADM5120_P335     23      /* ZyXEL Prestige 335/335WT */
++#define MACH_ADM5120_P335PLUS 24      /* ZyXEL Prestige 335Plus */
++#define MACH_ADM5120_P335U    25      /* ZyXEL Prestige 335U */
++#define MACH_ADM5120_ES2108   26      /* ZyXEL Ethernet Switch 2108 */
++#define MACH_ADM5120_ES2108F  27      /* ZyXEL Ethernet Switch 2108-F */
++#define MACH_ADM5120_ES2108G  28      /* ZyXEL Ethernet Switch 2108-G */
++#define MACH_ADM5120_ES2108LC 29      /* ZyXEL Ethernet Switch 2108-LC */
++#define MACH_ADM5120_ES2108PWR        30      /* ZyXEL Ethernet Switch 2108-PWR */
++#define MACH_ADM5120_ES2024A  31      /* ZyXEL Ethernet Switch 2024A */
++#define MACH_ADM5120_ES2024PWR        32      /* ZyXEL Ethernet Switch 2024PWR */
++#define MACH_ADM5120_CAS630   33      /* Cellvision CAS-630/630W */
++#define MACH_ADM5120_CAS670   34      /* Cellvision CAS-670/670W */
++#define MACH_ADM5120_CAS700   36      /* Cellvision CAS-700/700W */
++#define MACH_ADM5120_CAS771   37      /* Cellvision CAS-771/771W */
++#define MACH_ADM5120_CAS790   38      /* Cellvision CAS-790 */
++#define MACH_ADM5120_CAS861   39      /* Cellvision CAS-861/861W */
++#define MACH_ADM5120_NFS101U  40      /* Cellvision NFS-101U/101WU */
++#define MACH_ADM5120_NFS202U  41      /* Cellvision NFS-202U/202WU */
++#define MACH_ADM5120_EASY5120PATA 42  /* Infineon EASY 5120P-ATA */
++#define MACH_ADM5120_EASY5120RT 43    /* Infineon EASY 5120-RT */
++#define MACH_ADM5120_EASY5120WVOIP 44 /* Infineon EASY 5120-WVoIP */
++#define MACH_ADM5120_EASY83000        45      /* Infineon EASY-83000 */
++#define MACH_ADM5120_BR6104K  46      /* Edimax BR-6104K */
++#define MACH_ADM5120_RB_192   47      /* Mikrotik RouterBOARD 192 */
++
+ #define CL_SIZE                       COMMAND_LINE_SIZE
+ const char *get_system_type(void);
diff --git a/target/linux/adm5120/patches-2.6.23/002-adm5120_flash.patch b/target/linux/adm5120/patches-2.6.23/002-adm5120_flash.patch
new file mode 100644 (file)
index 0000000..4b5e887
--- /dev/null
@@ -0,0 +1,26 @@
+Index: linux-2.6.23/drivers/mtd/maps/Kconfig
+===================================================================
+--- linux-2.6.23.orig/drivers/mtd/maps/Kconfig
++++ linux-2.6.23/drivers/mtd/maps/Kconfig
+@@ -614,5 +614,9 @@ config MTD_PLATRAM
+         This selection automatically selects the map_ram driver.
++config MTD_ADM5120
++      tristate "Map driver for ADM5120 based boards"
++      depends on MIPS_ADM5120
++
+ endmenu
+Index: linux-2.6.23/drivers/mtd/maps/Makefile
+===================================================================
+--- linux-2.6.23.orig/drivers/mtd/maps/Makefile
++++ linux-2.6.23/drivers/mtd/maps/Makefile
+@@ -47,6 +47,7 @@ obj-$(CONFIG_MTD_OCELOT)     += ocelot.o
+ obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o
+ obj-$(CONFIG_MTD_PCI)         += pci.o
+ obj-$(CONFIG_MTD_ALCHEMY)       += alchemy-flash.o
++obj-$(CONFIG_MTD_ADM5120)             += adm5120-flash.o
+ obj-$(CONFIG_MTD_AUTCPU12)    += autcpu12-nvram.o
+ obj-$(CONFIG_MTD_EDB7312)     += edb7312.o
+ obj-$(CONFIG_MTD_IMPA7)               += impa7.o
diff --git a/target/linux/adm5120/patches-2.6.23/003-adm5120_switch.patch b/target/linux/adm5120/patches-2.6.23/003-adm5120_switch.patch
new file mode 100644 (file)
index 0000000..cb28a46
--- /dev/null
@@ -0,0 +1,27 @@
+Index: linux-2.6.23/drivers/net/Kconfig
+===================================================================
+--- linux-2.6.23.orig/drivers/net/Kconfig
++++ linux-2.6.23/drivers/net/Kconfig
+@@ -589,6 +589,10 @@ config MIPS_AU1X00_ENET
+         If you have an Alchemy Semi AU1X00 based system
+         say Y.  Otherwise, say N.
++config MIPS_ADM5120_ENET
++      tristate "MIPS ADM5120 Ethernet switch support"
++      depends on NET_ETHERNET && MIPS_ADM5120
++
+ config NET_SB1250_MAC
+       tristate "SB1250 Ethernet support"
+       depends on SIBYTE_SB1xxx_SOC
+Index: linux-2.6.23/drivers/net/Makefile
+===================================================================
+--- linux-2.6.23.orig/drivers/net/Makefile
++++ linux-2.6.23/drivers/net/Makefile
+@@ -174,6 +174,7 @@ obj-$(CONFIG_SC92031) += sc92031.o
+ # This is also a 82596 and should probably be merged
+ obj-$(CONFIG_LP486E) += lp486e.o
++obj-$(CONFIG_MIPS_ADM5120_ENET) += adm5120sw.o
+ obj-$(CONFIG_ETH16I) += eth16i.o
+ obj-$(CONFIG_ZORRO8390) += zorro8390.o
+ obj-$(CONFIG_HPLANCE) += hplance.o 7990.o
diff --git a/target/linux/adm5120/patches-2.6.23/004-adm5120_nand.patch b/target/linux/adm5120/patches-2.6.23/004-adm5120_nand.patch
new file mode 100644 (file)
index 0000000..ac90811
--- /dev/null
@@ -0,0 +1,33 @@
+Index: linux-2.6.23/drivers/mtd/nand/Kconfig
+===================================================================
+--- linux-2.6.23.orig/drivers/mtd/nand/Kconfig
++++ linux-2.6.23/drivers/mtd/nand/Kconfig
+@@ -81,6 +81,16 @@ config MTD_NAND_TS7250
+       help
+         Support for NAND flash on Technologic Systems TS-7250 platform.
++config MTD_NAND_ADM5120
++      tristate "ADM5120 NAND support"
++      depends on MTD_NAND && MIPS_ADM5120
++      help
++        This enables the driver for the ADM5120 SoC built-in
++        NAND flash interface.
++
++        No board specific support is done by this driver, each board
++        must advertise a platform_device for the driver to attach.
++
+ config MTD_NAND_IDS
+       tristate
+Index: linux-2.6.23/drivers/mtd/nand/Makefile
+===================================================================
+--- linux-2.6.23.orig/drivers/mtd/nand/Makefile
++++ linux-2.6.23/drivers/mtd/nand/Makefile
+@@ -10,6 +10,7 @@ obj-$(CONFIG_MTD_NAND_CAFE)          += cafe_nan
+ obj-$(CONFIG_MTD_NAND_SPIA)           += spia.o
+ obj-$(CONFIG_MTD_NAND_AMS_DELTA)      += ams-delta.o
+ obj-$(CONFIG_MTD_NAND_TOTO)           += toto.o
++obj-$(CONFIG_MTD_NAND_ADM5120)                += adm5120-nand.o
+ obj-$(CONFIG_MTD_NAND_AUTCPU12)               += autcpu12.o
+ obj-$(CONFIG_MTD_NAND_EDB7312)                += edb7312.o
+ obj-$(CONFIG_MTD_NAND_AU1550)         += au1550nd.o
diff --git a/target/linux/adm5120/patches-2.6.23/005-adm5120_usb.patch b/target/linux/adm5120/patches-2.6.23/005-adm5120_usb.patch
new file mode 100644 (file)
index 0000000..0b945ce
--- /dev/null
@@ -0,0 +1,35 @@
+Index: linux-2.6.23/drivers/usb/host/Kconfig
+===================================================================
+--- linux-2.6.23.orig/drivers/usb/host/Kconfig
++++ linux-2.6.23/drivers/usb/host/Kconfig
+@@ -261,3 +261,6 @@ config USB_R8A66597_HCD
+         To compile this driver as a module, choose M here: the
+         module will be called r8a66597-hcd.
++config USB_ADM5120_HCD
++      tristate "ADM5120 HCD support (EXPERIMENTAL)"
++      depends on USB && MIPS_ADM5120 && EXPERIMENTAL
+Index: linux-2.6.23/drivers/usb/host/Makefile
+===================================================================
+--- linux-2.6.23.orig/drivers/usb/host/Makefile
++++ linux-2.6.23/drivers/usb/host/Makefile
+@@ -8,6 +8,7 @@ endif
+ obj-$(CONFIG_PCI)             += pci-quirks.o
++obj-$(CONFIG_USB_ADM5120_HCD) += adm5120-hcd.o
+ obj-$(CONFIG_USB_EHCI_HCD)    += ehci-hcd.o
+ obj-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o
+ obj-$(CONFIG_USB_OHCI_HCD)    += ohci-hcd.o
+Index: linux-2.6.23/drivers/usb/Makefile
+===================================================================
+--- linux-2.6.23.orig/drivers/usb/Makefile
++++ linux-2.6.23/drivers/usb/Makefile
+@@ -16,6 +16,7 @@ obj-$(CONFIG_USB_UHCI_HCD)   += host/
+ obj-$(CONFIG_USB_SL811_HCD)   += host/
+ obj-$(CONFIG_USB_U132_HCD)    += host/
+ obj-$(CONFIG_USB_R8A66597_HCD)        += host/
++obj-$(CONFIG_USB_ADM5120_HCD)         += host/
+ obj-$(CONFIG_USB_ACM)         += class/
+ obj-$(CONFIG_USB_PRINTER)     += class/
diff --git a/target/linux/adm5120/patches-2.6.23/006-adm5120_leds.patch b/target/linux/adm5120/patches-2.6.23/006-adm5120_leds.patch
new file mode 100644 (file)
index 0000000..30f9234
--- /dev/null
@@ -0,0 +1,45 @@
+Index: linux-2.6.23/drivers/leds/Kconfig
+===================================================================
+--- linux-2.6.23.orig/drivers/leds/Kconfig
++++ linux-2.6.23/drivers/leds/Kconfig
+@@ -18,6 +18,27 @@ config LEDS_CLASS
+ comment "LED drivers"
++config LEDS_GPIO
++      tristate "LED support for LEDS on GPIO lines"
++      depends on LEDS_CLASS && GENERIC_GPIO
++      help
++        This option enables support for LEDs connected to GPIO lines
++
++config LEDS_ADM5120
++      tristate "LED Support for ADM5120 GPIO LEDs"
++      depends on LEDS_GPIO && MIPS_ADM5120
++      help
++        This option enables support for LEDs connected to GPIO lines
++        on ADM5120 SoC based platforms.
++
++config LEDS_ADM5120_EXPERIMENTAL
++      bool "Enable ADM5120 LEDs experimental code"
++      depends on LEDS_ADM5120
++
++config LEDS_ADM5120_DIAG
++      bool "Enable ADM5120 LEDs diagnostic mode"
++      depends on LEDS_ADM5120
++
+ config LEDS_CORGI
+       tristate "LED Support for the Sharp SL-C7x0 series"
+       depends on LEDS_CLASS && PXA_SHARP_C7xx
+Index: linux-2.6.23/drivers/leds/Makefile
+===================================================================
+--- linux-2.6.23.orig/drivers/leds/Makefile
++++ linux-2.6.23/drivers/leds/Makefile
+@@ -5,6 +5,8 @@ obj-$(CONFIG_LEDS_CLASS)               += led-class.o
+ obj-$(CONFIG_LEDS_TRIGGERS)           += led-triggers.o
+ # LED Platform Drivers
++obj-$(CONFIG_LEDS_GPIO)               += leds-gpio.o
++obj-$(CONFIG_LEDS_ADM5120)            += leds-adm5120.o
+ obj-$(CONFIG_LEDS_CORGI)              += leds-corgi.o
+ obj-$(CONFIG_LEDS_LOCOMO)             += leds-locomo.o
+ obj-$(CONFIG_LEDS_SPITZ)              += leds-spitz.o
diff --git a/target/linux/adm5120/patches-2.6.23/007-adm5120_pci.patch b/target/linux/adm5120/patches-2.6.23/007-adm5120_pci.patch
new file mode 100644 (file)
index 0000000..5e9fded
--- /dev/null
@@ -0,0 +1,23 @@
+Index: linux-2.6.23/arch/mips/pci/Makefile
+===================================================================
+--- linux-2.6.23.orig/arch/mips/pci/Makefile
++++ linux-2.6.23/arch/mips/pci/Makefile
+@@ -46,3 +46,4 @@ obj-$(CONFIG_TOSHIBA_RBTX4938)       += fixup-
+ obj-$(CONFIG_VICTOR_MPC30X)   += fixup-mpc30x.o
+ obj-$(CONFIG_ZAO_CAPCELLA)    += fixup-capcella.o
+ obj-$(CONFIG_WR_PPMC)         += fixup-wrppmc.o
++obj-$(CONFIG_PCI_ADM5120)     += pci-adm5120.o
+Index: linux-2.6.23/include/linux/pci_ids.h
+===================================================================
+--- linux-2.6.23.orig/include/linux/pci_ids.h
++++ linux-2.6.23/include/linux/pci_ids.h
+@@ -1690,6 +1690,9 @@
+ #define PCI_VENDOR_ID_ESDGMBH         0x12fe
+ #define PCI_DEVICE_ID_ESDGMBH_CPCIASIO4 0x0111
++#define PCI_VENDOR_ID_ADMTEK          0x1317
++#define PCI_DEVICE_ID_ADMTEK_ADM5120  0x5120
++
+ #define PCI_VENDOR_ID_SIIG            0x131f
+ #define PCI_SUBVENDOR_ID_SIIG         0x131f
+ #define PCI_DEVICE_ID_SIIG_1S_10x_550 0x1000
diff --git a/target/linux/adm5120/patches-2.6.23/008-adm5120_uart.patch b/target/linux/adm5120/patches-2.6.23/008-adm5120_uart.patch
new file mode 100644 (file)
index 0000000..cba4374
--- /dev/null
@@ -0,0 +1,53 @@
+Index: linux-2.6.23/drivers/serial/Makefile
+===================================================================
+--- linux-2.6.23.orig/drivers/serial/Makefile
++++ linux-2.6.23/drivers/serial/Makefile
+@@ -21,6 +21,7 @@ obj-$(CONFIG_SERIAL_8250_EXAR_ST16C554) 
+ obj-$(CONFIG_SERIAL_8250_HUB6) += 8250_hub6.o
+ obj-$(CONFIG_SERIAL_8250_MCA) += 8250_mca.o
+ obj-$(CONFIG_SERIAL_8250_AU1X00) += 8250_au1x00.o
++obj-$(CONFIG_SERIAL_ADM5120) += adm5120_uart.o
+ obj-$(CONFIG_SERIAL_AMBA_PL010) += amba-pl010.o
+ obj-$(CONFIG_SERIAL_AMBA_PL011) += amba-pl011.o
+ obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o
+Index: linux-2.6.23/include/linux/serial_core.h
+===================================================================
+--- linux-2.6.23.orig/include/linux/serial_core.h
++++ linux-2.6.23/include/linux/serial_core.h
+@@ -147,6 +147,9 @@
+ #define PORT_SB1250_DUART     77
++/* ADMtek ADM5120 SoC */
++#define PORT_ADM5120  77
++
+ #ifdef __KERNEL__
+ #include <linux/compiler.h>
+Index: linux-2.6.23/drivers/serial/Kconfig
+===================================================================
+--- linux-2.6.23.orig/drivers/serial/Kconfig
++++ linux-2.6.23/drivers/serial/Kconfig
+@@ -280,6 +280,22 @@ config SERIAL_8250_RM9K
+ comment "Non-8250 serial port support"
++config SERIAL_ADM5120
++       bool "ADM5120 serial port support"
++       depends on MIPS_ADM5120
++       select SERIAL_CORE
++       select SERIAL_CORE_CONSOLE
++       help
++         Driver for the on chip UARTs on the ADM5120 SoC
++
++config ADM5120_NR_UARTS
++       int "Maximum number of ADM5120 serial ports"
++       depends on SERIAL_ADM5120
++       default "2"
++       ---help---
++         Set this to the number of serial ports you want the driver to
++         support.
++
+ config SERIAL_AMBA_PL010
+       tristate "ARM AMBA PL010 serial port support"
+       depends on ARM_AMBA && (BROKEN || !ARCH_VERSATILE)
diff --git a/target/linux/adm5120/patches-2.6.23/100-mtd_myloder_partition_parser.patch b/target/linux/adm5120/patches-2.6.23/100-mtd_myloder_partition_parser.patch
new file mode 100644 (file)
index 0000000..fe7b1ed
--- /dev/null
@@ -0,0 +1,39 @@
+Index: linux-2.6.23/drivers/mtd/Kconfig
+===================================================================
+--- linux-2.6.23.orig/drivers/mtd/Kconfig
++++ linux-2.6.23/drivers/mtd/Kconfig
+@@ -160,6 +160,22 @@ config MTD_AFS_PARTS
+         for your particular device. It won't happen automatically. The
+         'armflash' map driver (CONFIG_MTD_ARMFLASH) does this, for example.
++config MTD_MYLOADER_PARTS
++      tristate "MyLoader partition parsing"
++      depends on MIPS_ADM5120 && MTD_PARTITIONS
++      ---help---
++        MyLoader is a bootloader which allows the user to define partitions
++        in flash devices, by putting a table in the second erase block
++        on the device, similar to a partition table. This table gives the 
++        offsets and lengths of the user defined partitions.
++
++        If you need code which can detect and parse these tables, and
++        register MTD 'partitions' corresponding to each image detected,
++        enable this option.
++
++        You will still need the parsing functions to be called by the driver
++        for your particular device. It won't happen automatically.
++
+ comment "User Modules And Translation Layers"
+ config MTD_CHAR
+Index: linux-2.6.23/drivers/mtd/Makefile
+===================================================================
+--- linux-2.6.23.orig/drivers/mtd/Makefile
++++ linux-2.6.23/drivers/mtd/Makefile
+@@ -11,6 +11,7 @@ obj-$(CONFIG_MTD_CONCAT)     += mtdconcat.o
+ obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o
+ obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o
+ obj-$(CONFIG_MTD_AFS_PARTS)   += afs.o
++obj-$(CONFIG_MTD_MYLOADER_PARTS) += myloader.o
+ # 'Users' - code which presents functionality to userspace.
+ obj-$(CONFIG_MTD_CHAR)                += mtdchar.o
diff --git a/target/linux/adm5120/patches-2.6.23/101-cfi_fixup_macronix_bootloc.patch b/target/linux/adm5120/patches-2.6.23/101-cfi_fixup_macronix_bootloc.patch
new file mode 100644 (file)
index 0000000..3650d4b
--- /dev/null
@@ -0,0 +1,95 @@
+Index: linux-2.6.23/drivers/mtd/chips/cfi_cmdset_0002.c
+===================================================================
+--- linux-2.6.23.orig/drivers/mtd/chips/cfi_cmdset_0002.c
++++ linux-2.6.23/drivers/mtd/chips/cfi_cmdset_0002.c
+@@ -47,12 +47,19 @@
+ #define MANUFACTURER_AMD      0x0001
+ #define MANUFACTURER_ATMEL    0x001F
+ #define MANUFACTURER_SST      0x00BF
++#define MANUFACTURER_MACRONIX 0x00C2
+ #define SST49LF004B           0x0060
+ #define SST49LF040B           0x0050
+ #define SST49LF008A           0x005a
+ #define AT49BV6416            0x00d6
+ #define MANUFACTURER_SAMSUNG  0x00ec
++/* Macronix */
++#define MX29LV160B    0x2249  /* MX29LV160 Bottom-boot chip */
++#define MX29LV160T    0x22C4  /* MX29LV160 Top-boot chip */
++#define MX29LV320B    0x22A8  /* MX29LV320 Bottom-boot chip */
++#define MX29LV320T    0x22A7  /* MX29LV320 Top-boot chip */
++
+ static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
+ static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
+ static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
+@@ -217,6 +224,41 @@ static void fixup_use_atmel_lock(struct 
+       mtd->flags |= MTD_STUPID_LOCK;
+ }
++#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++/*
++ * Some Macronix chips has no/bad bootblock information in the CFI table
++ */
++static void fixup_macronix_bootloc(struct mtd_info *mtd, void* param)
++{
++      struct map_info *map = mtd->priv;
++      struct cfi_private *cfi = map->fldrv_priv;
++      struct cfi_pri_amdstd *extp = cfi->cmdset_priv;
++      __u8 t;
++
++      switch (cfi->id) {
++      /* TODO: put affected chip ids here */
++      case MX29LV160B:
++      case MX29LV320B:
++              t = 2;  /* Bottom boot */
++              break;
++      case MX29LV160T:
++      case MX29LV320T:
++              t = 3;  /* Top boot */
++              break;
++      default:
++              return;
++      }
++
++      if (extp->TopBottom == t)
++              /* boot location detected by the CFI layer is correct */
++              return;
++
++      extp->TopBottom = t;
++      printk("%s: Macronix chip detected, id:0x%04X, boot location forced "
++              "to %s\n", map->name, cfi->id, (t == 2) ? "bottom" : "top");
++}
++#endif /* CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC */
++
+ static struct cfi_fixup cfi_fixup_table[] = {
+ #ifdef AMD_BOOTLOC_BUG
+       { CFI_MFR_AMD, CFI_ID_ANY, fixup_amd_bootblock, NULL },
+@@ -231,6 +273,9 @@ static struct cfi_fixup cfi_fixup_table[
+       { CFI_MFR_ANY, CFI_ID_ANY, fixup_use_write_buffers, NULL, },
+ #endif
+       { CFI_MFR_ATMEL, CFI_ID_ANY, fixup_convert_atmel_pri, NULL },
++#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++      { MANUFACTURER_MACRONIX, CFI_ID_ANY, fixup_macronix_bootloc, NULL, },
++#endif
+       { 0, 0, NULL, NULL }
+ };
+ static struct cfi_fixup jedec_fixup_table[] = {
+Index: linux-2.6.23/drivers/mtd/chips/Kconfig
+===================================================================
+--- linux-2.6.23.orig/drivers/mtd/chips/Kconfig
++++ linux-2.6.23/drivers/mtd/chips/Kconfig
+@@ -196,6 +196,14 @@ config MTD_CFI_AMDSTD
+         provides support for one of those command sets, used on chips
+         including the AMD Am29LV320.
++config MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++      bool "Fix boot-block location for Macronix flash chips"
++      depends on MTD_CFI_AMDSTD
++      help
++        Some Macronix flash chips have no/wrong boot-block location in the
++        CFI table, and the driver may detect the type incorrectly. Select
++        this if your board has such chip.
++
+ config MTD_CFI_STAA
+       tristate "Support for ST (Advanced Architecture) flash chips"
+       depends on MTD_GEN_PROBE
diff --git a/target/linux/adm5120/patches-2.6.23/102-jedec_pmc_39lvxxx_chips.patch b/target/linux/adm5120/patches-2.6.23/102-jedec_pmc_39lvxxx_chips.patch
new file mode 100644 (file)
index 0000000..b61396d
--- /dev/null
@@ -0,0 +1,74 @@
+Index: linux-2.6.23/drivers/mtd/chips/jedec_probe.c
+===================================================================
+--- linux-2.6.23.orig/drivers/mtd/chips/jedec_probe.c
++++ linux-2.6.23/drivers/mtd/chips/jedec_probe.c
+@@ -121,6 +121,10 @@
+ #define UPD29F064115  0x221C
+ /* PMC */
++#define PM39LV512     0x001B
++#define PM39LV010     0x001C
++#define PM39LV020     0x003D
++#define PM39LV040     0x003E
+ #define PM49FL002     0x006D
+ #define PM49FL004     0x006E
+ #define PM49FL008     0x006A
+@@ -1246,6 +1250,58 @@ static const struct amd_flash_info jedec
+                       ERASEINFO(0x02000,2),
+                       ERASEINFO(0x04000,1),
+               }
++        }, {
++              .mfr_id         = MANUFACTURER_PMC,
++              .dev_id         = PM39LV512,
++              .name           = "PMC Pm39LV512",
++              .uaddr          = {
++                      [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
++              },
++              .DevSize        = SIZE_64KiB,
++              .CmdSet         = P_ID_AMD_STD,
++              .NumEraseRegions= 1,
++              .regions        = {
++                      ERASEINFO(0x01000,16),
++              }
++        }, {
++              .mfr_id         = MANUFACTURER_PMC,
++              .dev_id         = PM39LV010,
++              .name           = "PMC Pm39LV010",
++              .uaddr          = {
++                      [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
++              },
++              .DevSize        = SIZE_128KiB,
++              .CmdSet         = P_ID_AMD_STD,
++              .NumEraseRegions= 1,
++              .regions        = {
++                      ERASEINFO(0x01000,32),
++              }
++        }, {
++              .mfr_id         = MANUFACTURER_PMC,
++              .dev_id         = PM39LV020,
++              .name           = "PMC Pm39LV020",
++              .uaddr          = {
++                      [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
++              },
++              .DevSize        = SIZE_256KiB,
++              .CmdSet         = P_ID_AMD_STD,
++              .NumEraseRegions= 1,
++              .regions        = {
++                      ERASEINFO(0x01000,64),
++              }
++        }, {
++              .mfr_id         = MANUFACTURER_PMC,
++              .dev_id         = PM39LV040,
++              .name           = "PMC Pm39LV040",
++              .uaddr          = {
++                      [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
++              },
++              .DevSize        = SIZE_512KiB,
++              .CmdSet         = P_ID_AMD_STD,
++              .NumEraseRegions= 1,
++              .regions        = {
++                      ERASEINFO(0x01000,128),
++              }
+       }, {
+               .mfr_id         = MANUFACTURER_PMC,
+               .dev_id         = PM49FL002,
diff --git a/target/linux/adm5120/patches-2.6.23/103-mtd_trxsplit.patch b/target/linux/adm5120/patches-2.6.23/103-mtd_trxsplit.patch
new file mode 100644 (file)
index 0000000..76f22d4
--- /dev/null
@@ -0,0 +1,28 @@
+Index: linux-2.6.23/drivers/mtd/Kconfig
+===================================================================
+--- linux-2.6.23.orig/drivers/mtd/Kconfig
++++ linux-2.6.23/drivers/mtd/Kconfig
+@@ -57,6 +57,11 @@ config MTD_ROOTFS_SPLIT
+       depends on MTD_PARTITIONS
+       default y
++config MTD_TRXSPLIT
++      bool "Automatically find and split TRX partitions"
++      depends on MTD_PARTITIONS
++      default n
++
+ config MTD_REDBOOT_PARTS
+       tristate "RedBoot partition table parsing"
+       depends on MTD_PARTITIONS
+Index: linux-2.6.23/drivers/mtd/Makefile
+===================================================================
+--- linux-2.6.23.orig/drivers/mtd/Makefile
++++ linux-2.6.23/drivers/mtd/Makefile
+@@ -8,6 +8,7 @@ mtd-y                          := mtdcore.o mtdsuper.o
+ mtd-$(CONFIG_MTD_PARTITIONS)  += mtdpart.o
+ obj-$(CONFIG_MTD_CONCAT)      += mtdconcat.o
++obj-$(CONFIG_MTD_TRXSPLIT)    += trxsplit.o
+ obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o
+ obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o
+ obj-$(CONFIG_MTD_AFS_PARTS)   += afs.o
diff --git a/target/linux/adm5120/patches-2.6.23/140-cmdline_hack.patch b/target/linux/adm5120/patches-2.6.23/140-cmdline_hack.patch
new file mode 100644 (file)
index 0000000..da0e001
--- /dev/null
@@ -0,0 +1,17 @@
+Index: linux-2.6.23/arch/mips/kernel/head.S
+===================================================================
+--- linux-2.6.23.orig/arch/mips/kernel/head.S
++++ linux-2.6.23/arch/mips/kernel/head.S
+@@ -136,7 +136,12 @@
+       /*
+        * Reserved space for exception handlers.
+        * Necessary for machines which link their kernels at KSEG0.
++       * Use as temporary storage for the kernel command line, so that it
++       * can be updated easily without having to relink the kernel.
+        */
++
++EXPORT(_image_cmdline)
++      .ascii "CMDLINE:"
+       .fill   0x400
+ #endif
diff --git a/target/linux/adm5120/patches-2.6.23/200-amba_pl010_hacks.patch b/target/linux/adm5120/patches-2.6.23/200-amba_pl010_hacks.patch
new file mode 100644 (file)
index 0000000..4923048
--- /dev/null
@@ -0,0 +1,297 @@
+Index: linux-2.6.23/drivers/serial/amba-pl010.c
+===================================================================
+--- linux-2.6.23.orig/drivers/serial/amba-pl010.c
++++ linux-2.6.23/drivers/serial/amba-pl010.c
+@@ -52,11 +52,10 @@
+ #include <asm/io.h>
+-#define UART_NR               8
+-
+ #define SERIAL_AMBA_MAJOR     204
+ #define SERIAL_AMBA_MINOR     16
+-#define SERIAL_AMBA_NR                UART_NR
++#define SERIAL_AMBA_NR                CONFIG_SERIAL_AMBA_PL010_NUMPORTS
++#define SERIAL_AMBA_NAME      CONFIG_SERIAL_AMBA_PL010_PORTNAME
+ #define AMBA_ISR_PASS_LIMIT   256
+@@ -82,7 +81,7 @@ static void pl010_stop_tx(struct uart_po
+       struct uart_amba_port *uap = (struct uart_amba_port *)port;
+       unsigned int cr;
+-      cr = readb(uap->port.membase + UART010_CR);
++      cr = readl(uap->port.membase + UART010_CR);
+       cr &= ~UART010_CR_TIE;
+       writel(cr, uap->port.membase + UART010_CR);
+ }
+@@ -92,7 +91,7 @@ static void pl010_start_tx(struct uart_p
+       struct uart_amba_port *uap = (struct uart_amba_port *)port;
+       unsigned int cr;
+-      cr = readb(uap->port.membase + UART010_CR);
++      cr = readl(uap->port.membase + UART010_CR);
+       cr |= UART010_CR_TIE;
+       writel(cr, uap->port.membase + UART010_CR);
+ }
+@@ -102,7 +101,7 @@ static void pl010_stop_rx(struct uart_po
+       struct uart_amba_port *uap = (struct uart_amba_port *)port;
+       unsigned int cr;
+-      cr = readb(uap->port.membase + UART010_CR);
++      cr = readl(uap->port.membase + UART010_CR);
+       cr &= ~(UART010_CR_RIE | UART010_CR_RTIE);
+       writel(cr, uap->port.membase + UART010_CR);
+ }
+@@ -112,7 +111,7 @@ static void pl010_enable_ms(struct uart_
+       struct uart_amba_port *uap = (struct uart_amba_port *)port;
+       unsigned int cr;
+-      cr = readb(uap->port.membase + UART010_CR);
++      cr = readl(uap->port.membase + UART010_CR);
+       cr |= UART010_CR_MSIE;
+       writel(cr, uap->port.membase + UART010_CR);
+ }
+@@ -122,9 +121,9 @@ static void pl010_rx_chars(struct uart_a
+       struct tty_struct *tty = uap->port.info->tty;
+       unsigned int status, ch, flag, rsr, max_count = 256;
+-      status = readb(uap->port.membase + UART01x_FR);
++      status = readl(uap->port.membase + UART01x_FR);
+       while (UART_RX_DATA(status) && max_count--) {
+-              ch = readb(uap->port.membase + UART01x_DR);
++              ch = readl(uap->port.membase + UART01x_DR);
+               flag = TTY_NORMAL;
+               uap->port.icount.rx++;
+@@ -133,7 +132,7 @@ static void pl010_rx_chars(struct uart_a
+                * Note that the error handling code is
+                * out of the main execution path
+                */
+-              rsr = readb(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
++              rsr = readl(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
+               if (unlikely(rsr & UART01x_RSR_ANY)) {
+                       writel(0, uap->port.membase + UART01x_ECR);
+@@ -165,7 +164,7 @@ static void pl010_rx_chars(struct uart_a
+               uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag);
+       ignore_char:
+-              status = readb(uap->port.membase + UART01x_FR);
++              status = readl(uap->port.membase + UART01x_FR);
+       }
+       spin_unlock(&uap->port.lock);
+       tty_flip_buffer_push(tty);
+@@ -210,7 +209,7 @@ static void pl010_modem_status(struct ua
+       writel(0, uap->port.membase + UART010_ICR);
+-      status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
++      status = readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+       delta = status ^ uap->old_status;
+       uap->old_status = status;
+@@ -238,7 +237,7 @@ static irqreturn_t pl010_int(int irq, vo
+       spin_lock(&uap->port.lock);
+-      status = readb(uap->port.membase + UART010_IIR);
++      status = readl(uap->port.membase + UART010_IIR);
+       if (status) {
+               do {
+                       if (status & (UART010_IIR_RTIS | UART010_IIR_RIS))
+@@ -251,7 +250,7 @@ static irqreturn_t pl010_int(int irq, vo
+                       if (pass_counter-- == 0)
+                               break;
+-                      status = readb(uap->port.membase + UART010_IIR);
++                      status = readl(uap->port.membase + UART010_IIR);
+               } while (status & (UART010_IIR_RTIS | UART010_IIR_RIS |
+                                  UART010_IIR_TIS));
+               handled = 1;
+@@ -265,7 +264,7 @@ static irqreturn_t pl010_int(int irq, vo
+ static unsigned int pl010_tx_empty(struct uart_port *port)
+ {
+       struct uart_amba_port *uap = (struct uart_amba_port *)port;
+-      unsigned int status = readb(uap->port.membase + UART01x_FR);
++      unsigned int status = readl(uap->port.membase + UART01x_FR);
+       return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT;
+ }
+@@ -275,7 +274,7 @@ static unsigned int pl010_get_mctrl(stru
+       unsigned int result = 0;
+       unsigned int status;
+-      status = readb(uap->port.membase + UART01x_FR);
++      status = readl(uap->port.membase + UART01x_FR);
+       if (status & UART01x_FR_DCD)
+               result |= TIOCM_CAR;
+       if (status & UART01x_FR_DSR)
+@@ -301,7 +300,7 @@ static void pl010_break_ctl(struct uart_
+       unsigned int lcr_h;
+       spin_lock_irqsave(&uap->port.lock, flags);
+-      lcr_h = readb(uap->port.membase + UART010_LCRH);
++      lcr_h = readl(uap->port.membase + UART010_LCRH);
+       if (break_state == -1)
+               lcr_h |= UART01x_LCRH_BRK;
+       else
+@@ -334,7 +333,7 @@ static int pl010_startup(struct uart_por
+       /*
+        * initialise the old status of the modem signals
+        */
+-      uap->old_status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
++      uap->old_status = readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+       /*
+        * Finally, enable interrupts
+@@ -365,7 +364,7 @@ static void pl010_shutdown(struct uart_p
+       writel(0, uap->port.membase + UART010_CR);
+       /* disable break condition and fifos */
+-      writel(readb(uap->port.membase + UART010_LCRH) &
++      writel(readl(uap->port.membase + UART010_LCRH) &
+               ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN),
+              uap->port.membase + UART010_LCRH);
+@@ -387,7 +386,7 @@ pl010_set_termios(struct uart_port *port
+       /*
+        * Ask the core to calculate the divisor for us.
+        */
+-      baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16); 
++      baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
+       quot = uart_get_divisor(port, baud);
+       switch (termios->c_cflag & CSIZE) {
+@@ -450,7 +449,7 @@ pl010_set_termios(struct uart_port *port
+               uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX;
+       /* first, disable everything */
+-      old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
++      old_cr = readl(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
+       if (UART_ENABLE_MS(port, termios->c_cflag))
+               old_cr |= UART010_CR_MSIE;
+@@ -540,7 +539,7 @@ static struct uart_ops amba_pl010_pops =
+       .verify_port    = pl010_verify_port,
+ };
+-static struct uart_amba_port *amba_ports[UART_NR];
++static struct uart_amba_port *amba_ports[SERIAL_AMBA_NR];
+ #ifdef CONFIG_SERIAL_AMBA_PL010_CONSOLE
+@@ -550,7 +549,7 @@ static void pl010_console_putchar(struct
+       unsigned int status;
+       do {
+-              status = readb(uap->port.membase + UART01x_FR);
++              status = readl(uap->port.membase + UART01x_FR);
+               barrier();
+       } while (!UART_TX_READY(status));
+       writel(ch, uap->port.membase + UART01x_DR);
+@@ -567,7 +566,7 @@ pl010_console_write(struct console *co, 
+       /*
+        *      First save the CR then disable the interrupts
+        */
+-      old_cr = readb(uap->port.membase + UART010_CR);
++      old_cr = readl(uap->port.membase + UART010_CR);
+       writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
+       uart_console_write(&uap->port, s, count, pl010_console_putchar);
+@@ -577,7 +576,7 @@ pl010_console_write(struct console *co, 
+        *      and restore the TCR
+        */
+       do {
+-              status = readb(uap->port.membase + UART01x_FR);
++              status = readl(uap->port.membase + UART01x_FR);
+               barrier();
+       } while (status & UART01x_FR_BUSY);
+       writel(old_cr, uap->port.membase + UART010_CR);
+@@ -589,9 +588,9 @@ static void __init
+ pl010_console_get_options(struct uart_amba_port *uap, int *baud,
+                            int *parity, int *bits)
+ {
+-      if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
++      if (readl(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
+               unsigned int lcr_h, quot;
+-              lcr_h = readb(uap->port.membase + UART010_LCRH);
++              lcr_h = readl(uap->port.membase + UART010_LCRH);
+               *parity = 'n';
+               if (lcr_h & UART01x_LCRH_PEN) {
+@@ -606,8 +605,8 @@ pl010_console_get_options(struct uart_am
+               else
+                       *bits = 8;
+-              quot = readb(uap->port.membase + UART010_LCRL) |
+-                     readb(uap->port.membase + UART010_LCRM) << 8;
++              quot = readl(uap->port.membase + UART010_LCRL) |
++                     readl(uap->port.membase + UART010_LCRM) << 8;
+               *baud = uap->port.uartclk / (16 * (quot + 1));
+       }
+ }
+@@ -625,7 +624,7 @@ static int __init pl010_console_setup(st
+        * if so, search for the first available port that does have
+        * console support.
+        */
+-      if (co->index >= UART_NR)
++      if (co->index >= SERIAL_AMBA_NR)
+               co->index = 0;
+       uap = amba_ports[co->index];
+       if (!uap)
+@@ -643,7 +642,7 @@ static int __init pl010_console_setup(st
+ static struct uart_driver amba_reg;
+ static struct console amba_console = {
+-      .name           = "ttyAM",
++      .name           = SERIAL_AMBA_NAME,
+       .write          = pl010_console_write,
+       .device         = uart_console_device,
+       .setup          = pl010_console_setup,
+@@ -659,11 +658,11 @@ static struct console amba_console = {
+ static struct uart_driver amba_reg = {
+       .owner                  = THIS_MODULE,
+-      .driver_name            = "ttyAM",
+-      .dev_name               = "ttyAM",
++      .driver_name            = SERIAL_AMBA_NAME,
++      .dev_name               = SERIAL_AMBA_NAME,
+       .major                  = SERIAL_AMBA_MAJOR,
+       .minor                  = SERIAL_AMBA_MINOR,
+-      .nr                     = UART_NR,
++      .nr                     = SERIAL_AMBA_NR,
+       .cons                   = AMBA_CONSOLE,
+ };
+Index: linux-2.6.23/drivers/serial/Kconfig
+===================================================================
+--- linux-2.6.23.orig/drivers/serial/Kconfig
++++ linux-2.6.23/drivers/serial/Kconfig
+@@ -303,10 +303,25 @@ config SERIAL_AMBA_PL010
+       help
+         This selects the ARM(R) AMBA(R) PrimeCell PL010 UART.  If you have
+         an Integrator/AP or Integrator/PP2 platform, or if you have a
+-        Cirrus Logic EP93xx CPU, say Y or M here.
++        Cirrus Logic EP93xx CPU or an Infineon ADM5120 SOC, say Y or M here.
+         If unsure, say N.
++config SERIAL_AMBA_PL010_NUMPORTS
++      int "Maximum number of AMBA PL010 serial ports"
++      depends on SERIAL_AMBA_PL010
++      default "8"
++      ---help---
++        Set this to the number of serial ports you want the AMBA PL010 driver
++        to support.
++
++config SERIAL_AMBA_PL010_PORTNAME
++      string "Name of the AMBA PL010 serial ports"
++      depends on SERIAL_AMBA_PL010
++      default "ttyAM"
++      ---help---
++        ::: To be written :::
++
+ config SERIAL_AMBA_PL010_CONSOLE
+       bool "Support for console on AMBA serial port"
+       depends on SERIAL_AMBA_PL010=y
diff --git a/target/linux/adm5120/patches-2.6.23/201-amba_bus_hacks.patch b/target/linux/adm5120/patches-2.6.23/201-amba_bus_hacks.patch
new file mode 100644 (file)
index 0000000..3d3fb59
--- /dev/null
@@ -0,0 +1,15 @@
+Index: linux-2.6.23/drivers/amba/bus.c
+===================================================================
+--- linux-2.6.23.orig/drivers/amba/bus.c
++++ linux-2.6.23/drivers/amba/bus.c
+@@ -17,6 +17,10 @@
+ #include <asm/io.h>
+ #include <asm/sizes.h>
++#ifndef NO_IRQ
++#define NO_IRQ                (-1)
++#endif
++
+ #define to_amba_device(d)     container_of(d, struct amba_device, dev)
+ #define to_amba_driver(d)     container_of(d, struct amba_driver, drv)
diff --git a/target/linux/adm5120/patches-2.6.23/300-i2c_gpio_custom.patch b/target/linux/adm5120/patches-2.6.23/300-i2c_gpio_custom.patch
new file mode 100644 (file)
index 0000000..2d18f46
--- /dev/null
@@ -0,0 +1,34 @@
+Index: linux-2.6.23/drivers/i2c/busses/Kconfig
+===================================================================
+--- linux-2.6.23.orig/drivers/i2c/busses/Kconfig
++++ linux-2.6.23/drivers/i2c/busses/Kconfig
+@@ -125,6 +125,17 @@ config I2C_GPIO
+         This is a very simple bitbanging I2C driver utilizing the
+         arch-neutral GPIO API to control the SCL and SDA lines.
++config I2C_GPIO_CUSTOM
++      tristate "Custom GPIO-based I2C driver"
++      depends on GENERIC_GPIO
++      select I2C_GPIO
++      help
++        This is an I2C driver to register 1 to 4 custom I2C buses using 
++        GPIO lines.
++
++        This support is also available as a module.  If so, the module
++        will be called i2c-gpio-custom.
++
+ config I2C_HYDRA
+       tristate "CHRP Apple Hydra Mac I/O I2C interface"
+       depends on PCI && PPC_CHRP && EXPERIMENTAL
+Index: linux-2.6.23/drivers/i2c/busses/Makefile
+===================================================================
+--- linux-2.6.23.orig/drivers/i2c/busses/Makefile
++++ linux-2.6.23/drivers/i2c/busses/Makefile
+@@ -13,6 +13,7 @@ obj-$(CONFIG_I2C_AU1550)     += i2c-au1550.o
+ obj-$(CONFIG_I2C_BLACKFIN_TWI)        += i2c-bfin-twi.o
+ obj-$(CONFIG_I2C_ELEKTOR)     += i2c-elektor.o
+ obj-$(CONFIG_I2C_GPIO)                += i2c-gpio.o
++obj-$(CONFIG_I2C_GPIO_CUSTOM) += i2c-gpio-custom.o
+ obj-$(CONFIG_I2C_HYDRA)               += i2c-hydra.o
+ obj-$(CONFIG_I2C_I801)                += i2c-i801.o
+ obj-$(CONFIG_I2C_I810)                += i2c-i810.o