ar71xx: Use PHY fixups for Open Mesh MR900
authorJohn Crispin <john@openwrt.org>
Wed, 16 Mar 2016 09:27:11 +0000 (09:27 +0000)
committerJohn Crispin <john@openwrt.org>
Wed, 16 Mar 2016 09:27:11 +0000 (09:27 +0000)
The delays of PHY/MAC on the MR900 are done by u-boot and OpenWrt in
different ways. u-boot only modifies the ETH_CFG of the QCA955x based on
the link speed. But OpenWrt can only modify the PHY delays based on the
link speed.

This can lead to communication problems when u-boot initializes the ETH_CFG
for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY
delays to an incompatible value.

Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and
only rely on the AT803x PHY settings.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
SVN-Revision: 49030

target/linux/ar71xx/files/arch/mips/ath79/mach-mr900.c

index 1eb33b6..efdfa2a 100644 (file)
@@ -23,6 +23,7 @@
 #include <linux/ath9k_platform.h>
 
 #include <asm/mach-ath79/ar71xx_regs.h>
+#include <linux/platform_data/phy-at803x.h>
 
 #include "common.h"
 #include "dev-ap9x-pci.h"
@@ -94,15 +95,30 @@ static struct gpio_keys_button mr900_gpio_keys[] __initdata = {
        },
 };
 
+static struct at803x_platform_data mr900_at803x_data = {
+       .disable_smarteee = 1,
+       .enable_rgmii_rx_delay = 1,
+       .enable_rgmii_tx_delay = 0,
+       .fixup_rgmii_tx_delay = 1,
+};
+
+static struct mdio_board_info mr900_mdio0_info[] = {
+       {
+               .bus_id = "ag71xx-mdio.0",
+               .phy_addr = 5,
+               .platform_data = &mr900_at803x_data,
+       },
+};
+
 static void __init mr900_setup(void)
 {
        u8 *art = (u8 *)KSEG1ADDR(0x1fff0000);
        u8 mac[6], pcie_mac[6];
        struct ath9k_platform_data *pdata;
 
-       ath79_eth0_pll_data.pll_1000 = 0xbe000101;
-       ath79_eth0_pll_data.pll_100 = 0x80000101;
-       ath79_eth0_pll_data.pll_10 = 0x80001313;
+       ath79_eth0_pll_data.pll_1000 = 0xae000000;
+       ath79_eth0_pll_data.pll_100 = 0xa0000101;
+       ath79_eth0_pll_data.pll_10 = 0xa0001313;
 
        ath79_register_m25p80(NULL);
 
@@ -126,6 +142,9 @@ static void __init mr900_setup(void)
        ath79_setup_qca955x_eth_cfg(QCA955X_ETH_CFG_RGMII_EN, 3, 3, 0, 0);
        ath79_register_mdio(0, 0x0);
 
+       mdiobus_register_board_info(mr900_mdio0_info,
+                                   ARRAY_SIZE(mr900_mdio0_info));
+
        ath79_init_mac(ath79_eth0_data.mac_addr, art + MR900_MAC0_OFFSET, 0);
 
        /* GMAC0 is connected to the RMGII interface */