sunxi: add support for Lamobo R1
authorZoltan Herpai <wigyori@uid0.hu>
Fri, 30 Jan 2015 00:17:16 +0000 (00:17 +0000)
committerZoltan Herpai <wigyori@uid0.hu>
Fri, 30 Jan 2015 00:17:16 +0000 (00:17 +0000)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 44214

target/linux/sunxi/base-files/etc/uci-defaults/02_network
target/linux/sunxi/base-files/lib/sunxi.sh
target/linux/sunxi/config-3.18
target/linux/sunxi/image/Makefile
target/linux/sunxi/patches-3.18/302-dt-sun7i-add-lamobo-r1.patch [new file with mode: 0644]
target/linux/sunxi/profiles/lamobo-r1.mk [new file with mode: 0644]

index d801677..372fed9 100644 (file)
@@ -16,6 +16,12 @@ case "$( sunxi_board_name )" in
 "olinuxino-micro"*)
        ucidef_set_interface_lan 'wlan0'
        ;;
+"lamobo-r1")
+       ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
+       ucidef_add_switch "switch0" "1" "1"
+       ucidef_add_switch_vlan "switch0" "1" "4 0 1 2 8t"
+       ucidef_add_switch_vlan "switch0" "2" "3 8t"
+       ;;
 *)
        ucidef_set_interface_lan 'eth0'
        ;;
index d4dd9fe..444c7e9 100644 (file)
@@ -105,6 +105,10 @@ sunxi_board_detect() {
                        board="i12-tvbox"
                        ;;
 
+               "Lamobo R1")
+                       board="lamobo-r1"
+                       ;;
+
                "Olimex A20-OLinuXino-LIME")
                        board="olinuxino-lime"
                        ;;
index 68f1593..3513f6a 100644 (file)
@@ -58,6 +58,11 @@ CONFIG_AUDIT=y
 CONFIG_AUDIT_GENERIC=y
 CONFIG_AUTO_ZRELADDR=y
 CONFIG_AVERAGE=y
+CONFIG_B53=y
+# CONFIG_B53_MMAP_DRIVER is not set
+CONFIG_B53_PHY_DRIVER=y
+CONFIG_B53_PHY_FIXUP=y
+# CONFIG_B53_SRAB_DRIVER is not set
 CONFIG_BINFMT_MISC=y
 CONFIG_BLK_CGROUP=y
 CONFIG_BLK_DEV_SD=y
@@ -427,6 +432,7 @@ CONFIG_STRICT_DEVMEM=y
 CONFIG_SUN4I_TIMER=y
 CONFIG_SUN5I_HSTIMER=y
 CONFIG_SUNXI_WATCHDOG=y
+CONFIG_SWCONFIG=y
 CONFIG_SWIOTLB=y
 CONFIG_SWP_EMULATE=y
 CONFIG_SYSFS_SYSCALL=y
index 4475aa8..f627ee3 100644 (file)
@@ -24,7 +24,8 @@ BOARDS:= \
        sun7i-a20-cubietruck \
        sun7i-a20-olinuxino-lime \
        sun7i-a20-olinuxino-micro \
-       sun7i-a20-pcduino3
+       sun7i-a20-pcduino3 \
+       sun7i-a20-lamobo-r1
 
 define Image/BuildKernel
        mkimage -A arm -O linux -T kernel -C none \
@@ -88,6 +89,10 @@ define Image/Build/Profile/Bananapro
        $(call Image/Build/SDCard,$(1),sun7i-a20-bananapro)
 endef
 
+define Image/Build/Profile/Lamobo_R1
+       $(call Image/Build/SDCard,$(1),sun7i-a20-lamobo-r1)
+endef
+
 define Image/Build/Profile/Cubieboard
        $(call Image/Build/SDCard,$(1),sun4i-a10-cubieboard)
 endef
diff --git a/target/linux/sunxi/patches-3.18/302-dt-sun7i-add-lamobo-r1.patch b/target/linux/sunxi/patches-3.18/302-dt-sun7i-add-lamobo-r1.patch
new file mode 100644 (file)
index 0000000..82c8bd5
--- /dev/null
@@ -0,0 +1,252 @@
+Index: linux-3.18.2/arch/arm/boot/dts/Makefile
+===================================================================
+--- linux-3.18.2.orig/arch/arm/boot/dts/Makefile
++++ linux-3.18.2/arch/arm/boot/dts/Makefile
+@@ -441,6 +441,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
+       sun7i-a20-cubietruck.dtb \
+       sun7i-a20-hummingbird.dtb \
+       sun7i-a20-i12-tvbox.dtb \
++      sun7i-a20-lamobo-r1.dtb \
+       sun7i-a20-olinuxino-lime.dtb \
+       sun7i-a20-olinuxino-micro.dtb \
+       sun7i-a20-pcduino3.dtb
+Index: linux-3.18.2/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts
+===================================================================
+--- /dev/null
++++ linux-3.18.2/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts
+@@ -0,0 +1,235 @@
++/*
++ * Copyright 2015 Daniel Golle <daniel@makrotopia.org>
++ * Copyright 2014 Hans de Goede <hdegoede@redhat.com>
++ *
++ * This file is dual-licensed: you can use it either under the terms
++ * of the GPL or the X11 license, at your option. Note that this dual
++ * licensing only applies to this file, and not this project as a
++ * whole.
++ *
++ *  a) This library is free software; you can redistribute it and/or
++ *     modify it under the terms of the GNU General Public License as
++ *     published by the Free Software Foundation; either version 2 of the
++ *     License, or (at your option) any later version.
++ *
++ *     This library is distributed in the hope that it will be useful,
++ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
++ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ *     GNU General Public License for more details.
++ *
++ *     You should have received a copy of the GNU General Public
++ *     License along with this library; if not, write to the Free
++ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
++ *     MA 02110-1301 USA
++ *
++ * Or, alternatively,
++ *
++ *  b) Permission is hereby granted, free of charge, to any person
++ *     obtaining a copy of this software and associated documentation
++ *     files (the "Software"), to deal in the Software without
++ *     restriction, including without limitation the rights to use,
++ *     copy, modify, merge, publish, distribute, sublicense, and/or
++ *     sell copies of the Software, and to permit persons to whom the
++ *     Software is furnished to do so, subject to the following
++ *     conditions:
++ *
++ *     The above copyright notice and this permission notice shall be
++ *     included in all copies or substantial portions of the Software.
++ *
++ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
++ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
++ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
++ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
++ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
++ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
++ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
++ *     OTHER DEALINGS IN THE SOFTWARE.
++ */
++
++/dts-v1/;
++/include/ "sun7i-a20.dtsi"
++/include/ "sunxi-common-regulators.dtsi"
++#include <dt-bindings/input/input.h>
++
++/ {
++      model = "Lamobo R1";
++      compatible = "lamobo,lamobo-r1", "allwinner,sun7i-a20";
++
++      soc@01c00000 {
++              spi0: spi@01c05000 {
++                      pinctrl-names = "default";
++                      pinctrl-0 = <&spi0_pins_a>;
++                      status = "okay";
++              };
++
++              mmc0: mmc@01c0f000 {
++                      pinctrl-names = "default";
++                      pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_lamobo>;
++                      vmmc-supply = <&reg_vcc3v3>;
++                      bus-width = <4>;
++                      cd-gpios = <&pio 7 10 0>; /* PH10 */
++                      cd-inverted;
++                      status = "okay";
++              };
++
++              usbphy: phy@01c13400 {
++                      usb1_vbus-supply = <&reg_usb1_vbus>;
++                      usb2_vbus-supply = <&reg_usb2_vbus>;
++                      status = "okay";
++              };
++
++              ehci0: usb@01c14000 {
++                      status = "okay";
++              };
++
++              ohci0: usb@01c14400 {
++                      status = "okay";
++              };
++
++              ahci: sata@01c18000 {
++                      target-supply = <&reg_ahci_5v>;
++                      status = "okay";
++              };
++
++              ehci1: usb@01c1c000 {
++                      status = "okay";
++              };
++
++              ohci1: usb@01c1c400 {
++                      status = "okay";
++              };
++
++              pinctrl@01c20800 {
++                      mmc0_cd_pin_lamobo: mmc0_cd_pin@0 {
++                              allwinner,pins = "PH10";
++                              allwinner,function = "gpio_in";
++                              allwinner,drive = <0>;
++                              allwinner,pull = <1>;
++                      };
++
++                      gmac_power_pin_lamobo: gmac_power_pin@0 {
++                              allwinner,pins = "PH23";
++                              allwinner,function = "gpio_out";
++                              allwinner,drive = <0>;
++                              allwinner,pull = <0>;
++                      };
++
++                      led_pins_lamobo: led_pins@0 {
++                              allwinner,pins = "PH2";
++                              allwinner,function = "gpio_out";
++                              allwinner,drive = <1>;
++                              allwinner,pull = <0>;
++                      };
++              };
++
++              lradc: lradc@01c22800 {
++                      allwinner,chan0-step = <200>;
++                      linux,chan0-keycodes = <KEY_VOLUMEUP KEY_VOLUMEDOWN
++                                              KEY_MENU KEY_SEARCH KEY_HOME
++                                              KEY_ESC KEY_ENTER>;
++                      status = "okay";
++              };
++
++              ir0: ir@01c21800 {
++                      pinctrl-names = "default";
++                      pinctrl-0 = <&ir0_pins_a>;
++                      status = "okay";
++              };
++
++              uart0: serial@01c28000 {
++                      pinctrl-names = "default";
++                      pinctrl-0 = <&uart0_pins_a>;
++                      status = "okay";
++              };
++
++              uart3: serial@01c28c00 {
++                      pinctrl-names = "default";
++                      pinctrl-0 = <&uart3_pins_b>;
++                      status = "okay";
++              };
++
++              uart7: serial@01c29c00 {
++                      pinctrl-names = "default";
++                      pinctrl-0 = <&uart7_pins_a>;
++                      status = "okay";
++              };
++
++              i2c0: i2c@01c2ac00 {
++                      pinctrl-names = "default";
++                      pinctrl-0 = <&i2c0_pins_a>;
++                      status = "okay";
++
++                      axp209: pmic@34 {
++                              compatible = "x-powers,axp209";
++                              reg = <0x34>;
++                              interrupt-parent = <&nmi_intc>;
++                              interrupts = <0 8>;
++
++                              interrupt-controller;
++                              #interrupt-cells = <1>;
++                      };
++              };
++
++              i2c1: i2c@01c2b000 {
++                      pinctrl-names = "default";
++                      pinctrl-0 = <&i2c1_pins_a>;
++                      status = "okay";
++              };
++
++              i2c2: i2c@01c2b400 {
++                      pinctrl-names = "default";
++                      pinctrl-0 = <&i2c2_pins_a>;
++                      status = "okay";
++              };
++
++              gmac: ethernet@01c50000 {
++                      pinctrl-names = "default";
++                      pinctrl-0 = <&gmac_pins_rgmii_a>;
++                      phy = <&phy1>;
++                      phy-mode = "rgmii";
++                      phy-supply = <&reg_gmac_3v3>;
++                      status = "okay";
++
++                      phy1: ethernet-phy@1 {
++                              reg = <1>;
++                      };
++              };
++      };
++
++      leds {
++              compatible = "gpio-leds";
++              pinctrl-names = "default";
++              pinctrl-0 = <&led_pins_lamobo>;
++
++              green {
++                      label = "lamobo:green:usr";
++                      gpios = <&pio 7 24 0>;
++                      default-state = "on";
++              };
++      };
++
++      reg_ahci_5v: ahci-5v {
++              status = "okay";
++      };
++
++      reg_usb1_vbus: usb1-vbus {
++              status = "okay";
++      };
++
++      reg_usb2_vbus: usb2-vbus {
++              status = "okay";
++      };
++
++      reg_gmac_3v3: gmac-3v3 {
++              compatible = "regulator-fixed";
++              pinctrl-names = "default";
++              pinctrl-0 = <&gmac_power_pin_lamobo>;
++              regulator-name = "gmac-3v3";
++              regulator-min-microvolt = <3300000>;
++              regulator-max-microvolt = <3300000>;
++              startup-delay-us = <100000>;
++              enable-active-high;
++              gpio = <&pio 7 23 0>;
++              status = "okay";
++      };
++};
diff --git a/target/linux/sunxi/profiles/lamobo-r1.mk b/target/linux/sunxi/profiles/lamobo-r1.mk
new file mode 100644 (file)
index 0000000..4bc1185
--- /dev/null
@@ -0,0 +1,19 @@
+#
+# Copyright (C) 2015 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/Lamobo_R1
+       NAME:=Lamobo R1
+       PACKAGES:=\
+               uboot-sunxi-Lamobo_R1 kmod-ata-sunxi kmod-rtl8192cu \
+               swconfig wpad-mini
+endef
+
+define Profile/Lamobo_R1/Description
+       Package set optimized for the Lamobo R1
+endef
+
+$(eval $(call Profile,Lamobo_R1))