[brcm63xx] remove support for 2.6.37 and 2.6.38
authorFlorian Fainelli <florian@openwrt.org>
Sun, 19 Jun 2011 20:14:22 +0000 (20:14 +0000)
committerFlorian Fainelli <florian@openwrt.org>
Sun, 19 Jun 2011 20:14:22 +0000 (20:14 +0000)
SVN-Revision: 27233

79 files changed:
target/linux/brcm63xx/config-2.6.37 [deleted file]
target/linux/brcm63xx/config-2.6.38 [deleted file]
target/linux/brcm63xx/patches-2.6.37/001-6345_cpu.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/007-usb-ohci-support.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/008-usb-ehci-support.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/010-add_bcm63xx_ohci_controller.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/011-add_bcm63xx_ehci_controller.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/040-bcm963xx_flashmap.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/041-bcm963xx_real_rootfs_length.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/070_bcm63xx_enet_vlan_incoming_fixed.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/080-bcm6345_enet.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/100-reset_buttons.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/110-gpiodev.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/141-led_count.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/180-udc_preliminary_support.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/200-extended-platform-devices.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/200-spi-board-info.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/210-no_ehci_over_current_check.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/220-wl_exports.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/230-6358-enet1-external-mii-clk.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/240-spi.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/250-boardid_fixup.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/300-alice_gate2_leds.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/310-96348gw_a_leds.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/440-board-D4PW.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/441-board-NB4.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/442-board-96338W2_E7T.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/443-board-CPVA642.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/444-board_dsl_274xb_rev_c.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/445-board_spw500v.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/447-board_gw6200_gw6000.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/448-board-MAGIC.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/449-board_hw553.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/450-board_rta1320_16m.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/451-board_spw303v.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/452-board_V2500V.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/453-board_BTV2110.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/454-board_livebox.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/455-board_ct536_ct5621.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/456-board-RTA770BW.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/500-ssb-add-callback-for-sprom.patch [deleted file]
target/linux/brcm63xx/patches-2.6.37/977-ssb_export_fallback_sprom.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/007-usb-ohci-support.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/008-usb-ehci-support.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/010-add_bcm63xx_ohci_controller.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/011-add_bcm63xx_ehci_controller.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/040-bcm963xx_flashmap.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/041-bcm963xx_real_rootfs_length.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/070_bcm63xx_enet_vlan_incoming_fixed.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/100-reset_buttons.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/110-gpiodev.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/141-led_count.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/180-udc_preliminary_support.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/200-extended-platform-devices.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/200-spi-board-info.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/210-no_ehci_over_current_check.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/220-wl_exports.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/230-6358-enet1-external-mii-clk.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/240-spi.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/250-boardid_fixup.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/300-alice_gate2_leds.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/310-96348gw_a_leds.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/440-board-D4PW.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/441-board-NB4.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/442-board-96338W2_E7T.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/443-board-CPVA642.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/444-board_dsl_274xb_rev_c.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/445-board_spw500v.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/447-board_gw6200_gw6000.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/448-board-MAGIC.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/449-board_hw553.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/450-board_rta1320_16m.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/451-board_spw303v.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/452-board_V2500V.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/453-board_BTV2110.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/454-board_livebox.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/455-board_ct536_ct5621.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/500-ssb-add-callback-for-sprom.patch [deleted file]
target/linux/brcm63xx/patches-2.6.38/977-ssb_export_fallback_sprom.patch [deleted file]

diff --git a/target/linux/brcm63xx/config-2.6.37 b/target/linux/brcm63xx/config-2.6.37
deleted file mode 100644 (file)
index ab2fdb1..0000000
+++ /dev/null
@@ -1,160 +0,0 @@
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set
-CONFIG_ARCH_POPULATES_NODE_MAP=y
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-# CONFIG_ARCH_SUPPORTS_MSI is not set
-CONFIG_ARCH_SUPPORTS_OPROFILE=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_AUDIT=y
-CONFIG_AUDIT_GENERIC=y
-# CONFIG_AUTO_IRQ_AFFINITY is not set
-CONFIG_BCM63XX=y
-CONFIG_BCM63XX_CPU_6338=y
-CONFIG_BCM63XX_CPU_6345=y
-CONFIG_BCM63XX_CPU_6348=y
-CONFIG_BCM63XX_CPU_6358=y
-CONFIG_BCM63XX_ENET=y
-CONFIG_BCM63XX_PHY=y
-CONFIG_BCM63XX_WDT=y
-CONFIG_BKL=y
-CONFIG_BOARD_BCM963XX=y
-# CONFIG_BOARD_LIVEBOX is not set
-CONFIG_BSD_PROCESS_ACCT_V3=y
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_CEVT_R4K=y
-CONFIG_CEVT_R4K_LIB=y
-CONFIG_CMDLINE="root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200"
-CONFIG_CMDLINE_BOOL=y
-# CONFIG_CMDLINE_OVERRIDE is not set
-CONFIG_CPU_BIG_ENDIAN=y
-CONFIG_CPU_HAS_PREFETCH=y
-CONFIG_CPU_HAS_SYNC=y
-CONFIG_CPU_MIPS32=y
-CONFIG_CPU_MIPS32_R1=y
-CONFIG_CPU_MIPSR1=y
-CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
-CONFIG_CPU_SUPPORTS_HIGHMEM=y
-CONFIG_CRAMFS=y
-CONFIG_CSRC_R4K=y
-CONFIG_CSRC_R4K_LIB=y
-CONFIG_DECOMPRESS_LZMA=y
-CONFIG_DMA_NONCOHERENT=y
-CONFIG_EARLY_PRINTK=y
-CONFIG_ELF_CORE=y
-CONFIG_FIRMWARE_IN_KERNEL=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_GENERIC_CMOS_UPDATE=y
-CONFIG_GENERIC_FIND_LAST_BIT=y
-CONFIG_GENERIC_FIND_NEXT_BIT=y
-CONFIG_GENERIC_GPIO=y
-# CONFIG_GENERIC_HARDIRQS_NO_DEPRECATED is not set
-CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
-# CONFIG_GENERIC_PENDING_IRQ is not set
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_74X164=y
-CONFIG_GPIO_DEVICE=y
-CONFIG_GPIO_SYSFS=y
-# CONFIG_HAMRADIO is not set
-# CONFIG_HARDIRQS_SW_RESEND is not set
-CONFIG_HARDWARE_WATCHPOINTS=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_ATTRS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_GENERIC_HARDIRQS=y
-CONFIG_HAVE_IDE=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_PERF_EVENTS=y
-# CONFIG_HAVE_SPARSE_IRQ is not set
-CONFIG_HW_HAS_PCI=y
-CONFIG_HW_RANDOM=y
-CONFIG_HZ=250
-# CONFIG_HZ_100 is not set
-CONFIG_HZ_250=y
-CONFIG_IMAGE_CMDLINE_HACK=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_INOTIFY_USER=y
-CONFIG_IP_PIMSM_V1=y
-CONFIG_IP_PIMSM_V2=y
-CONFIG_IRQ_CPU=y
-# CONFIG_IRQ_PER_CPU is not set
-CONFIG_KEXEC=y
-CONFIG_LEDS_GPIO=y
-# CONFIG_LEDS_TRIGGER_HEARTBEAT is not set
-CONFIG_LOONGSON_UART_BASE=y
-CONFIG_MACH_NO_WESTBRIDGE=y
-CONFIG_MIPS=y
-CONFIG_MIPS_L1_CACHE_SHIFT=5
-# CONFIG_MIPS_MACHINE is not set
-CONFIG_MIPS_MT_DISABLED=y
-CONFIG_MODULE_FORCE_LOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MTD_BCM963XX=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-CONFIG_MTD_CFI_BE_BYTE_SWAP=y
-# CONFIG_MTD_CFI_GEOMETRY is not set
-# CONFIG_MTD_CFI_NOSWAP is not set
-CONFIG_MTD_CFI_STAA=y
-CONFIG_MTD_CMDLINE_PARTS=y
-# CONFIG_MTD_COMPLEX_MAPPINGS is not set
-CONFIG_MTD_CONCAT=y
-CONFIG_MTD_JEDECPROBE=y
-CONFIG_MTD_REDBOOT_PARTS=y
-CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_PER_CPU_KM=y
-CONFIG_PAGEFLAGS_EXTENDED=y
-CONFIG_PCI=y
-CONFIG_PCI_DOMAINS=y
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PHYLIB=y
-CONFIG_POSIX_MQUEUE=y
-CONFIG_POSIX_MQUEUE_SYSCTL=y
-# CONFIG_PREEMPT_RCU is not set
-# CONFIG_QUOTACTL is not set
-CONFIG_RELAY=y
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SERIAL_8250 is not set
-CONFIG_SERIAL_BCM63XX=y
-CONFIG_SERIAL_BCM63XX_CONSOLE=y
-CONFIG_SPI=y
-# CONFIG_SPI_BCM63XX is not set
-CONFIG_SPI_BITBANG=y
-CONFIG_SPI_GPIO=y
-CONFIG_SPI_MASTER=y
-CONFIG_SQUASHFS_EMBEDDED=y
-CONFIG_SSB=y
-CONFIG_SSB_B43_PCI_BRIDGE=y
-CONFIG_SSB_BLOCKIO=y
-# CONFIG_SSB_DRIVER_MIPS is not set
-CONFIG_SSB_DRIVER_PCICORE=y
-CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
-CONFIG_SSB_PCIHOST=y
-CONFIG_SSB_PCIHOST_POSSIBLE=y
-CONFIG_SSB_SPROM=y
-CONFIG_SWAP_IO_SPACE=y
-CONFIG_SYS_HAS_CPU_MIPS32_R1=y
-CONFIG_SYS_HAS_EARLY_PRINTK=y
-CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
-CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
-CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
-CONFIG_USB_EHCI_BIG_ENDIAN_MMIO=y
-CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
-CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
-CONFIG_USB_SUPPORT=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_WATCHDOG_NOWAYOUT=y
-CONFIG_ZONE_DMA_FLAG=0
diff --git a/target/linux/brcm63xx/config-2.6.38 b/target/linux/brcm63xx/config-2.6.38
deleted file mode 100644 (file)
index f2205ee..0000000
+++ /dev/null
@@ -1,165 +0,0 @@
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set
-CONFIG_ARCH_POPULATES_NODE_MAP=y
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-# CONFIG_ARCH_SUPPORTS_MSI is not set
-CONFIG_ARCH_SUPPORTS_OPROFILE=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-# CONFIG_ATH79 is not set
-CONFIG_AUDIT=y
-CONFIG_AUDIT_GENERIC=y
-# CONFIG_AUTO_IRQ_AFFINITY is not set
-CONFIG_BCM63XX=y
-CONFIG_BCM63XX_CPU_6338=y
-CONFIG_BCM63XX_CPU_6345=y
-CONFIG_BCM63XX_CPU_6348=y
-CONFIG_BCM63XX_CPU_6358=y
-CONFIG_BCM63XX_ENET=y
-CONFIG_BCM63XX_PHY=y
-CONFIG_BCM63XX_WDT=y
-CONFIG_BOARD_BCM963XX=y
-# CONFIG_BOARD_LIVEBOX is not set
-CONFIG_BOOTPARAM_HUNG_TASK_PANIC=y
-CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=1
-CONFIG_BSD_PROCESS_ACCT_V3=y
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_CEVT_R4K=y
-CONFIG_CEVT_R4K_LIB=y
-CONFIG_CMDLINE="root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200"
-CONFIG_CMDLINE_BOOL=y
-# CONFIG_CMDLINE_OVERRIDE is not set
-CONFIG_CPU_BIG_ENDIAN=y
-CONFIG_CPU_HAS_PREFETCH=y
-CONFIG_CPU_HAS_SYNC=y
-CONFIG_CPU_MIPS32=y
-CONFIG_CPU_MIPS32_R1=y
-CONFIG_CPU_MIPSR1=y
-CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
-CONFIG_CPU_SUPPORTS_HIGHMEM=y
-CONFIG_CRAMFS=y
-CONFIG_CSRC_R4K=y
-CONFIG_CSRC_R4K_LIB=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DECOMPRESS_LZMA=y
-CONFIG_DETECT_HUNG_TASK=y
-CONFIG_DMA_NONCOHERENT=y
-CONFIG_EARLY_PRINTK=y
-CONFIG_ELF_CORE=y
-CONFIG_FIRMWARE_IN_KERNEL=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_GENERIC_CMOS_UPDATE=y
-CONFIG_GENERIC_FIND_LAST_BIT=y
-CONFIG_GENERIC_FIND_NEXT_BIT=y
-CONFIG_GENERIC_GPIO=y
-# CONFIG_GENERIC_HARDIRQS_NO_DEPRECATED is not set
-# CONFIG_GENERIC_PENDING_IRQ is not set
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_74X164=y
-CONFIG_GPIO_DEVICE=y
-CONFIG_GPIO_SYSFS=y
-# CONFIG_HAMRADIO is not set
-# CONFIG_HARDIRQS_SW_RESEND is not set
-CONFIG_HARDWARE_WATCHPOINTS=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_ATTRS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_GENERIC_HARDIRQS=y
-CONFIG_HAVE_IDE=y
-CONFIG_HAVE_IRQ_WORK=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_PERF_EVENTS=y
-# CONFIG_HAVE_SPARSE_IRQ is not set
-CONFIG_HW_HAS_PCI=y
-CONFIG_HW_RANDOM=y
-CONFIG_HZ=250
-# CONFIG_HZ_100 is not set
-CONFIG_HZ_250=y
-CONFIG_IMAGE_CMDLINE_HACK=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_INOTIFY_USER=y
-CONFIG_IP_PIMSM_V1=y
-CONFIG_IP_PIMSM_V2=y
-CONFIG_IRQ_CPU=y
-# CONFIG_IRQ_PER_CPU is not set
-CONFIG_KEXEC=y
-CONFIG_LEDS_GPIO=y
-CONFIG_MACH_NO_WESTBRIDGE=y
-CONFIG_MIPS=y
-CONFIG_MIPS_L1_CACHE_SHIFT=5
-# CONFIG_MIPS_MACHINE is not set
-CONFIG_MIPS_MT_DISABLED=y
-CONFIG_MODULE_FORCE_LOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MTD_BCM963XX=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-CONFIG_MTD_CFI_BE_BYTE_SWAP=y
-# CONFIG_MTD_CFI_GEOMETRY is not set
-# CONFIG_MTD_CFI_NOSWAP is not set
-CONFIG_MTD_CFI_STAA=y
-CONFIG_MTD_CMDLINE_PARTS=y
-# CONFIG_MTD_COMPLEX_MAPPINGS is not set
-CONFIG_MTD_CONCAT=y
-CONFIG_MTD_JEDECPROBE=y
-CONFIG_MTD_REDBOOT_PARTS=y
-CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_PER_CPU_KM=y
-CONFIG_PAGEFLAGS_EXTENDED=y
-CONFIG_PCI=y
-CONFIG_PCI_DOMAINS=y
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PHYLIB=y
-CONFIG_POSIX_MQUEUE=y
-CONFIG_POSIX_MQUEUE_SYSCTL=y
-# CONFIG_PREEMPT_RCU is not set
-# CONFIG_QUOTACTL is not set
-CONFIG_RELAY=y
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SERIAL_8250 is not set
-CONFIG_SERIAL_BCM63XX=y
-CONFIG_SERIAL_BCM63XX_CONSOLE=y
-CONFIG_SPI=y
-# CONFIG_SPI_BCM63XX is not set
-CONFIG_SPI_BITBANG=y
-CONFIG_SPI_GPIO=y
-CONFIG_SPI_MASTER=y
-# CONFIG_SPI_PXA2XX_PCI is not set
-CONFIG_SQUASHFS_EMBEDDED=y
-CONFIG_SSB=y
-CONFIG_SSB_B43_PCI_BRIDGE=y
-CONFIG_SSB_BLOCKIO=y
-# CONFIG_SSB_DRIVER_MIPS is not set
-CONFIG_SSB_DRIVER_PCICORE=y
-CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
-CONFIG_SSB_PCIHOST=y
-CONFIG_SSB_PCIHOST_POSSIBLE=y
-CONFIG_SSB_SPROM=y
-CONFIG_SWAP_IO_SPACE=y
-CONFIG_SYS_HAS_CPU_MIPS32_R1=y
-CONFIG_SYS_HAS_EARLY_PRINTK=y
-CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
-CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
-CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
-CONFIG_USB_EHCI_BIG_ENDIAN_MMIO=y
-CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
-CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
-CONFIG_USB_SUPPORT=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_WATCHDOG_NOWAYOUT=y
-CONFIG_XZ_DEC=y
-CONFIG_ZONE_DMA_FLAG=0
diff --git a/target/linux/brcm63xx/patches-2.6.37/001-6345_cpu.patch b/target/linux/brcm63xx/patches-2.6.37/001-6345_cpu.patch
deleted file mode 100644 (file)
index 16751e5..0000000
+++ /dev/null
@@ -1,74 +0,0 @@
---- a/arch/mips/bcm63xx/cpu.c
-+++ b/arch/mips/bcm63xx/cpu.c
-@@ -260,8 +260,10 @@ static unsigned int detect_memory_size(v
-       unsigned int cols = 0, rows = 0, is_32bits = 0, banks = 0;
-       u32 val;
--      if (BCMCPU_IS_6345())
--              return (8 * 1024 * 1024);
-+      if (BCMCPU_IS_6345()) {
-+              val = bcm_sdram_readl(SDRAM_MBASE_REG);
-+              return (val * 8 * 1024 * 1024);
-+      }
-       if (BCMCPU_IS_6338() || BCMCPU_IS_6348()) {
-               val = bcm_sdram_readl(SDRAM_CFG_REG);
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -735,6 +735,8 @@
- #define SDRAM_CFG_BANK_SHIFT          13
- #define SDRAM_CFG_BANK_MASK           (1 << SDRAM_CFG_BANK_SHIFT)
-+#define SDRAM_MBASE_REG                       0xc
-+
- #define SDRAM_PRIO_REG                        0x2C
- #define SDRAM_PRIO_MIPS_SHIFT         29
- #define SDRAM_PRIO_MIPS_MASK          (1 << SDRAM_PRIO_MIPS_SHIFT)
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -698,15 +698,9 @@ void __init board_prom_init(void)
-       char cfe_version[32];
-       u32 val;
--      /* read base address of boot chip select (0)
--       * 6345 does not have MPI but boots from standard
--       * MIPS Flash address */
--      if (BCMCPU_IS_6345())
--              val = 0x1fc00000;
--      else {
--              val = bcm_mpi_readl(MPI_CSBASE_REG(0));
--              val &= MPI_CSBASE_BASE_MASK;
--      }
-+      /* read base address of boot chip select (0) */
-+      val = bcm_mpi_readl(MPI_CSBASE_REG(0));
-+      val &= MPI_CSBASE_BASE_MASK;
-       boot_addr = (u8 *)KSEG1ADDR(val);
-       /* dump cfe version */
-@@ -881,12 +875,9 @@ int __init board_register_devices(void)
-               bcm63xx_dsp_register(&board.dsp);
-       /* read base address of boot chip select (0) */
--      if (BCMCPU_IS_6345())
--              val = 0x1fc00000;
--      else {
--              val = bcm_mpi_readl(MPI_CSBASE_REG(0));
--              val &= MPI_CSBASE_BASE_MASK;
--      }
-+      val = bcm_mpi_readl(MPI_CSBASE_REG(0));
-+      val &= MPI_CSBASE_BASE_MASK;
-+
-       mtd_resources[0].start = val;
-       mtd_resources[0].end = 0x1FFFFFFF;
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-@@ -163,7 +163,7 @@ enum bcm63xx_regs_set {
- #define BCM_6345_ENET0_BASE           (0xfffe1800)
- #define BCM_6345_ENETDMA_BASE         (0xfffe2800)
- #define BCM_6345_PCMCIA_BASE          (0xfffe2028)
--#define BCM_6345_MPI_BASE             (0xdeadbeef)
-+#define BCM_6345_MPI_BASE             (0xfffe2000)
- #define BCM_6345_OHCI0_BASE           (0xfffe2100)
- #define BCM_6345_OHCI_PRIV_BASE               (0xfffe2200)
- #define BCM_6345_USBH_PRIV_BASE               (0xdeadbeef)
diff --git a/target/linux/brcm63xx/patches-2.6.37/007-usb-ohci-support.patch b/target/linux/brcm63xx/patches-2.6.37/007-usb-ohci-support.patch
deleted file mode 100644 (file)
index a70b501..0000000
+++ /dev/null
@@ -1,125 +0,0 @@
-The bcm63xx SOC has an integrated OHCI controller, this patch adds
-platform device registration and change board code to register ohci
-device when necessary.
-
-Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
----
- arch/mips/bcm63xx/Kconfig                          |    6 ++
- arch/mips/bcm63xx/Makefile                         |    3 +-
- arch/mips/bcm63xx/boards/board_bcm963xx.c          |    4 ++
- arch/mips/bcm63xx/dev-usb-ohci.c                   |   49 ++++++++++++++++++++
- .../asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h        |    6 ++
- 5 files changed, 67 insertions(+), 1 deletions(-)
- create mode 100644 arch/mips/bcm63xx/dev-usb-ohci.c
- create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h
-
---- a/arch/mips/bcm63xx/Kconfig
-+++ b/arch/mips/bcm63xx/Kconfig
-@@ -16,10 +16,16 @@ config BCM63XX_CPU_6345
- config BCM63XX_CPU_6348
-       bool "support 6348 CPU"
-       select HW_HAS_PCI
-+      select USB_ARCH_HAS_OHCI
-+      select USB_OHCI_BIG_ENDIAN_DESC
-+      select USB_OHCI_BIG_ENDIAN_MMIO
- config BCM63XX_CPU_6358
-       bool "support 6358 CPU"
-       select HW_HAS_PCI
-+      select USB_ARCH_HAS_OHCI
-+      select USB_OHCI_BIG_ENDIAN_DESC
-+      select USB_OHCI_BIG_ENDIAN_MMIO
- endmenu
- source "arch/mips/bcm63xx/boards/Kconfig"
---- a/arch/mips/bcm63xx/Makefile
-+++ b/arch/mips/bcm63xx/Makefile
-@@ -1,5 +1,6 @@
- obj-y         += clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \
--                 dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o dev-wdt.o
-+                 dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o dev-wdt.o \
-+                 dev-usb-ohci.o
- obj-$(CONFIG_EARLY_PRINTK)    += early_printk.o
- obj-y         += boards/
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -25,6 +25,7 @@
- #include <bcm63xx_dev_enet.h>
- #include <bcm63xx_dev_dsp.h>
- #include <bcm63xx_dev_pcmcia.h>
-+#include <bcm63xx_dev_usb_ohci.h>
- #include <board_bcm963xx.h>
- #define PFX   "board_bcm963xx: "
-@@ -877,6 +878,9 @@ int __init board_register_devices(void)
-           !board_get_mac_address(board.enet1.mac_addr))
-               bcm63xx_enet_register(1, &board.enet1);
-+      if (board.has_ohci0)
-+              bcm63xx_ohci_register();
-+
-       if (board.has_dsp)
-               bcm63xx_dsp_register(&board.dsp);
---- /dev/null
-+++ b/arch/mips/bcm63xx/dev-usb-ohci.c
-@@ -0,0 +1,49 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2010 Maxime Bizon <mbizon@freebox.fr>
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/kernel.h>
-+#include <linux/platform_device.h>
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_dev_usb_ohci.h>
-+
-+static struct resource ohci_resources[] = {
-+      {
-+              /* start & end filled at runtime */
-+              .flags          = IORESOURCE_MEM,
-+      },
-+      {
-+              /* start filled at runtime */
-+              .flags          = IORESOURCE_IRQ,
-+      },
-+};
-+
-+static u64 ohci_dmamask = ~(u32)0;
-+
-+static struct platform_device bcm63xx_ohci_device = {
-+      .name           = "bcm63xx_ohci",
-+      .id             = 0,
-+      .num_resources  = ARRAY_SIZE(ohci_resources),
-+      .resource       = ohci_resources,
-+      .dev            = {
-+              .dma_mask               = &ohci_dmamask,
-+              .coherent_dma_mask      = 0xffffffff,
-+      },
-+};
-+
-+int __init bcm63xx_ohci_register(void)
-+{
-+      if (!BCMCPU_IS_6348() && !BCMCPU_IS_6358())
-+              return 0;
-+
-+      ohci_resources[0].start = bcm63xx_regset_address(RSET_OHCI0);
-+      ohci_resources[0].end = ohci_resources[0].start;
-+      ohci_resources[0].end += RSET_OHCI_SIZE - 1;
-+      ohci_resources[1].start = bcm63xx_get_irq_number(IRQ_OHCI0);
-+      return platform_device_register(&bcm63xx_ohci_device);
-+}
---- /dev/null
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h
-@@ -0,0 +1,6 @@
-+#ifndef BCM63XX_DEV_USB_OHCI_H_
-+#define BCM63XX_DEV_USB_OHCI_H_
-+
-+int bcm63xx_ohci_register(void);
-+
-+#endif /* BCM63XX_DEV_USB_OHCI_H_ */
diff --git a/target/linux/brcm63xx/patches-2.6.37/008-usb-ehci-support.patch b/target/linux/brcm63xx/patches-2.6.37/008-usb-ehci-support.patch
deleted file mode 100644 (file)
index 0c236f0..0000000
+++ /dev/null
@@ -1,117 +0,0 @@
-The bcm63xx SOC has an integrated EHCI controller, this patch adds
-platform device registration and change board code to register
-EHCI device when necessary.
-
-Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
----
- arch/mips/bcm63xx/Kconfig                          |    2 +
- arch/mips/bcm63xx/Makefile                         |    2 +-
- arch/mips/bcm63xx/boards/board_bcm963xx.c          |    4 ++
- arch/mips/bcm63xx/dev-usb-ehci.c                   |   49 ++++++++++++++++++++
- .../asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h        |    6 ++
- 5 files changed, 62 insertions(+), 1 deletions(-)
- create mode 100644 arch/mips/bcm63xx/dev-usb-ehci.c
- create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h
-
---- a/arch/mips/bcm63xx/Kconfig
-+++ b/arch/mips/bcm63xx/Kconfig
-@@ -26,6 +26,8 @@ config BCM63XX_CPU_6358
-       select USB_ARCH_HAS_OHCI
-       select USB_OHCI_BIG_ENDIAN_DESC
-       select USB_OHCI_BIG_ENDIAN_MMIO
-+      select USB_ARCH_HAS_EHCI
-+      select USB_EHCI_BIG_ENDIAN_MMIO
- endmenu
- source "arch/mips/bcm63xx/boards/Kconfig"
---- a/arch/mips/bcm63xx/Makefile
-+++ b/arch/mips/bcm63xx/Makefile
-@@ -1,6 +1,6 @@
- obj-y         += clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \
-                  dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o dev-wdt.o \
--                 dev-usb-ohci.o
-+                 dev-usb-ohci.o dev-usb-ehci.o
- obj-$(CONFIG_EARLY_PRINTK)    += early_printk.o
- obj-y         += boards/
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -26,6 +26,7 @@
- #include <bcm63xx_dev_dsp.h>
- #include <bcm63xx_dev_pcmcia.h>
- #include <bcm63xx_dev_usb_ohci.h>
-+#include <bcm63xx_dev_usb_ehci.h>
- #include <board_bcm963xx.h>
- #define PFX   "board_bcm963xx: "
-@@ -878,6 +879,9 @@ int __init board_register_devices(void)
-           !board_get_mac_address(board.enet1.mac_addr))
-               bcm63xx_enet_register(1, &board.enet1);
-+      if (board.has_ehci0)
-+              bcm63xx_ehci_register();
-+
-       if (board.has_ohci0)
-               bcm63xx_ohci_register();
---- /dev/null
-+++ b/arch/mips/bcm63xx/dev-usb-ehci.c
-@@ -0,0 +1,49 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2010 Maxime Bizon <mbizon@freebox.fr>
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/kernel.h>
-+#include <linux/platform_device.h>
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_dev_usb_ehci.h>
-+
-+static struct resource ehci_resources[] = {
-+      {
-+              /* start & end filled at runtime */
-+              .flags          = IORESOURCE_MEM,
-+      },
-+      {
-+              /* start filled at runtime */
-+              .flags          = IORESOURCE_IRQ,
-+      },
-+};
-+
-+static u64 ehci_dmamask = ~(u32)0;
-+
-+static struct platform_device bcm63xx_ehci_device = {
-+      .name           = "bcm63xx_ehci",
-+      .id             = 0,
-+      .num_resources  = ARRAY_SIZE(ehci_resources),
-+      .resource       = ehci_resources,
-+      .dev            = {
-+              .dma_mask               = &ehci_dmamask,
-+              .coherent_dma_mask      = 0xffffffff,
-+      },
-+};
-+
-+int __init bcm63xx_ehci_register(void)
-+{
-+      if (!BCMCPU_IS_6358())
-+              return 0;
-+
-+      ehci_resources[0].start = bcm63xx_regset_address(RSET_EHCI0);
-+      ehci_resources[0].end = ehci_resources[0].start;
-+      ehci_resources[0].end += RSET_EHCI_SIZE - 1;
-+      ehci_resources[1].start = bcm63xx_get_irq_number(IRQ_EHCI0);
-+      return platform_device_register(&bcm63xx_ehci_device);
-+}
---- /dev/null
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h
-@@ -0,0 +1,6 @@
-+#ifndef BCM63XX_DEV_USB_EHCI_H_
-+#define BCM63XX_DEV_USB_EHCI_H_
-+
-+int bcm63xx_ehci_register(void);
-+
-+#endif /* BCM63XX_DEV_USB_EHCI_H_ */
diff --git a/target/linux/brcm63xx/patches-2.6.37/010-add_bcm63xx_ohci_controller.patch b/target/linux/brcm63xx/patches-2.6.37/010-add_bcm63xx_ohci_controller.patch
deleted file mode 100644 (file)
index a7a66ec..0000000
+++ /dev/null
@@ -1,202 +0,0 @@
-Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
----
- drivers/usb/host/ohci-bcm63xx.c |  166 +++++++++++++++++++++++++++++++++++++++
- drivers/usb/host/ohci-hcd.c     |    5 +
- drivers/usb/host/ohci.h         |    2 +-
- 3 files changed, 172 insertions(+), 1 deletions(-)
- create mode 100644 drivers/usb/host/ohci-bcm63xx.c
-
---- /dev/null
-+++ b/drivers/usb/host/ohci-bcm63xx.c
-@@ -0,0 +1,166 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2010 Maxime Bizon <mbizon@freebox.fr>
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/clk.h>
-+#include <linux/platform_device.h>
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_regs.h>
-+#include <bcm63xx_io.h>
-+
-+static struct clk *usb_host_clock;
-+
-+static int __devinit ohci_bcm63xx_start(struct usb_hcd *hcd)
-+{
-+      struct ohci_hcd *ohci = hcd_to_ohci(hcd);
-+      int ret;
-+
-+        /*
-+         * port 2 can be shared with USB slave, but all boards seem to
-+         * have only one host port populated, so we can hardcode it
-+         */
-+      ohci->num_ports = 1;
-+
-+      ret = ohci_init(ohci);
-+      if (ret < 0)
-+              return ret;
-+
-+      ret = ohci_run(ohci);
-+      if (ret < 0) {
-+              err("can't start %s", hcd->self.bus_name);
-+              ohci_stop(hcd);
-+              return ret;
-+      }
-+      return 0;
-+}
-+
-+static const struct hc_driver ohci_bcm63xx_hc_driver = {
-+      .description =          hcd_name,
-+      .product_desc =         "BCM63XX integrated OHCI controller",
-+      .hcd_priv_size =        sizeof(struct ohci_hcd),
-+
-+      .irq =                  ohci_irq,
-+      .flags =                HCD_USB11 | HCD_MEMORY,
-+      .start =                ohci_bcm63xx_start,
-+      .stop =                 ohci_stop,
-+      .shutdown =             ohci_shutdown,
-+      .urb_enqueue =          ohci_urb_enqueue,
-+      .urb_dequeue =          ohci_urb_dequeue,
-+      .endpoint_disable =     ohci_endpoint_disable,
-+      .get_frame_number =     ohci_get_frame,
-+      .hub_status_data =      ohci_hub_status_data,
-+      .hub_control =          ohci_hub_control,
-+      .start_port_reset =     ohci_start_port_reset,
-+};
-+
-+static int __devinit ohci_hcd_bcm63xx_drv_probe(struct platform_device *pdev)
-+{
-+      struct resource *res_mem;
-+      struct usb_hcd *hcd;
-+      struct ohci_hcd *ohci;
-+      u32 reg;
-+      int ret, irq;
-+
-+      res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+      irq = platform_get_irq(pdev, 0);
-+      if (!res_mem || irq < 0)
-+              return -ENODEV;
-+
-+      if (BCMCPU_IS_6348()) {
-+              struct clk *clk;
-+              /* enable USB host clock */
-+              clk = clk_get(&pdev->dev, "usbh");
-+              if (IS_ERR(clk))
-+                      return -ENODEV;
-+
-+              clk_enable(clk);
-+              usb_host_clock = clk;
-+              bcm_rset_writel(RSET_OHCI_PRIV, 0, OHCI_PRIV_REG);
-+
-+      } else if (BCMCPU_IS_6358()) {
-+              reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_REG);
-+              reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK;
-+              reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK;
-+              bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_REG);
-+              /*
-+               * The magic value comes for the original vendor BSP
-+               * and is needed for USB to work. Datasheet does not
-+               * help, so the magic value is used as-is.
-+               */
-+              bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020, USBH_PRIV_TEST_REG);
-+      } else
-+              return 0;
-+
-+      hcd = usb_create_hcd(&ohci_bcm63xx_hc_driver, &pdev->dev, "bcm63xx");
-+      if (!hcd)
-+              return -ENOMEM;
-+      hcd->rsrc_start = res_mem->start;
-+      hcd->rsrc_len = res_mem->end - res_mem->start + 1;
-+
-+      if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
-+              pr_debug("request_mem_region failed\n");
-+              ret = -EBUSY;
-+              goto out;
-+      }
-+
-+      hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
-+      if (!hcd->regs) {
-+              pr_debug("ioremap failed\n");
-+              ret = -EIO;
-+              goto out1;
-+      }
-+
-+      ohci = hcd_to_ohci(hcd);
-+      ohci->flags |= OHCI_QUIRK_BE_MMIO | OHCI_QUIRK_BE_DESC |
-+              OHCI_QUIRK_FRAME_NO;
-+      ohci_hcd_init(ohci);
-+
-+      ret = usb_add_hcd(hcd, irq, IRQF_DISABLED);
-+      if (ret)
-+              goto out2;
-+
-+      platform_set_drvdata(pdev, hcd);
-+      return 0;
-+
-+out2:
-+      iounmap(hcd->regs);
-+out1:
-+      release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
-+out:
-+      usb_put_hcd(hcd);
-+      return ret;
-+}
-+
-+static int __devexit ohci_hcd_bcm63xx_drv_remove(struct platform_device *pdev)
-+{
-+      struct usb_hcd *hcd;
-+
-+      hcd = platform_get_drvdata(pdev);
-+      usb_remove_hcd(hcd);
-+      iounmap(hcd->regs);
-+      usb_put_hcd(hcd);
-+      release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
-+      if (usb_host_clock) {
-+              clk_disable(usb_host_clock);
-+              clk_put(usb_host_clock);
-+      }
-+      platform_set_drvdata(pdev, NULL);
-+      return 0;
-+}
-+
-+static struct platform_driver ohci_hcd_bcm63xx_driver = {
-+      .probe          = ohci_hcd_bcm63xx_drv_probe,
-+      .remove         = __devexit_p(ohci_hcd_bcm63xx_drv_remove),
-+      .shutdown       = usb_hcd_platform_shutdown,
-+      .driver         = {
-+              .name   = "bcm63xx_ohci",
-+              .owner  = THIS_MODULE,
-+      },
-+};
-+
-+MODULE_ALIAS("platform:bcm63xx_ohci");
---- a/drivers/usb/host/ohci-hcd.c
-+++ b/drivers/usb/host/ohci-hcd.c
-@@ -1067,6 +1067,11 @@ MODULE_LICENSE ("GPL");
- #define PLATFORM_DRIVER               ohci_hcd_da8xx_driver
- #endif
-+#ifdef CONFIG_BCM63XX
-+#include "ohci-bcm63xx.c"
-+#define PLATFORM_DRIVER               ohci_hcd_bcm63xx_driver
-+#endif
-+
- #if defined(CONFIG_CPU_SUBTYPE_SH7720) || \
-     defined(CONFIG_CPU_SUBTYPE_SH7721) || \
-     defined(CONFIG_CPU_SUBTYPE_SH7763) || \
---- a/drivers/usb/host/ohci.h
-+++ b/drivers/usb/host/ohci.h
-@@ -656,7 +656,7 @@ static inline u32 hc32_to_cpup (const st
-  * some big-endian SOC implementations.  Same thing happens with PSW access.
-  */
--#ifdef CONFIG_PPC_MPC52xx
-+#if defined(CONFIG_PPC_MPC52xx) || defined(CONFIG_BCM63XX)
- #define big_endian_frame_no_quirk(ohci)       (ohci->flags & OHCI_QUIRK_FRAME_NO)
- #else
- #define big_endian_frame_no_quirk(ohci)       0
diff --git a/target/linux/brcm63xx/patches-2.6.37/011-add_bcm63xx_ehci_controller.patch b/target/linux/brcm63xx/patches-2.6.37/011-add_bcm63xx_ehci_controller.patch
deleted file mode 100644 (file)
index e6e763d..0000000
+++ /dev/null
@@ -1,178 +0,0 @@
-Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
----
- drivers/usb/host/ehci-bcm63xx.c |  154 +++++++++++++++++++++++++++++++++++++++
- drivers/usb/host/ehci-hcd.c     |    5 +
- 2 files changed, 159 insertions(+), 0 deletions(-)
- create mode 100644 drivers/usb/host/ehci-bcm63xx.c
-
---- /dev/null
-+++ b/drivers/usb/host/ehci-bcm63xx.c
-@@ -0,0 +1,154 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/platform_device.h>
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_regs.h>
-+#include <bcm63xx_io.h>
-+
-+static int ehci_bcm63xx_setup(struct usb_hcd *hcd)
-+{
-+      struct ehci_hcd *ehci = hcd_to_ehci(hcd);
-+      int retval;
-+
-+      retval = ehci_halt(ehci);
-+      if (retval)
-+              return retval;
-+
-+      retval = ehci_init(hcd);
-+      if (retval)
-+              return retval;
-+
-+      ehci_reset(ehci);
-+      ehci_port_power(ehci, 0);
-+
-+      return retval;
-+}
-+
-+
-+static const struct hc_driver ehci_bcm63xx_hc_driver = {
-+      .description =          hcd_name,
-+      .product_desc =         "BCM63XX integrated EHCI controller",
-+      .hcd_priv_size =        sizeof(struct ehci_hcd),
-+
-+      .irq =                  ehci_irq,
-+      .flags =                HCD_MEMORY | HCD_USB2,
-+
-+      .reset =                ehci_bcm63xx_setup,
-+      .start =                ehci_run,
-+      .stop =                 ehci_stop,
-+      .shutdown =             ehci_shutdown,
-+
-+      .urb_enqueue =          ehci_urb_enqueue,
-+      .urb_dequeue =          ehci_urb_dequeue,
-+      .endpoint_disable =     ehci_endpoint_disable,
-+
-+      .get_frame_number =     ehci_get_frame,
-+
-+      .hub_status_data =      ehci_hub_status_data,
-+      .hub_control =          ehci_hub_control,
-+      .bus_suspend =          ehci_bus_suspend,
-+      .bus_resume =           ehci_bus_resume,
-+      .relinquish_port =      ehci_relinquish_port,
-+      .port_handed_over =     ehci_port_handed_over,
-+};
-+
-+static int __devinit ehci_hcd_bcm63xx_drv_probe(struct platform_device *pdev)
-+{
-+      struct resource *res_mem;
-+      struct usb_hcd *hcd;
-+      struct ehci_hcd *ehci;
-+      u32 reg;
-+      int ret, irq;
-+
-+      res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+      irq = platform_get_irq(pdev, 0);;
-+      if (!res_mem || irq < 0)
-+              return -ENODEV;
-+
-+      reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_REG);
-+      reg &= ~USBH_PRIV_SWAP_EHCI_DATA_MASK;
-+      reg |= USBH_PRIV_SWAP_EHCI_ENDN_MASK;
-+      bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_REG);
-+
-+      /*
-+       * The magic value comes for the original vendor BSP and is
-+       * needed for USB to work. Datasheet does not help, so the
-+       * magic value is used as-is.
-+       */
-+      bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020, USBH_PRIV_TEST_REG);
-+
-+      hcd = usb_create_hcd(&ehci_bcm63xx_hc_driver, &pdev->dev, "bcm63xx");
-+      if (!hcd)
-+              return -ENOMEM;
-+      hcd->rsrc_start = res_mem->start;
-+      hcd->rsrc_len = res_mem->end - res_mem->start + 1;
-+
-+      if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
-+              pr_debug("request_mem_region failed\n");
-+              ret = -EBUSY;
-+              goto out;
-+      }
-+
-+      hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
-+      if (!hcd->regs) {
-+              pr_debug("ioremap failed\n");
-+              ret = -EIO;
-+              goto out1;
-+      }
-+
-+      ehci = hcd_to_ehci(hcd);
-+      ehci->big_endian_mmio = 1;
-+      ehci->big_endian_desc = 0;
-+      ehci->caps = hcd->regs;
-+      ehci->regs = hcd->regs +
-+              HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase));
-+      ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
-+      ehci->sbrn = 0x20;
-+
-+      ret = usb_add_hcd(hcd, irq, IRQF_DISABLED);
-+      if (ret)
-+              goto out2;
-+
-+      platform_set_drvdata(pdev, hcd);
-+      return 0;
-+
-+out2:
-+      iounmap(hcd->regs);
-+out1:
-+      release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
-+out:
-+      usb_put_hcd(hcd);
-+      return ret;
-+}
-+
-+static int __devexit ehci_hcd_bcm63xx_drv_remove(struct platform_device *pdev)
-+{
-+      struct usb_hcd *hcd;
-+
-+      hcd = platform_get_drvdata(pdev);
-+      usb_remove_hcd(hcd);
-+      iounmap(hcd->regs);
-+      usb_put_hcd(hcd);
-+      release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
-+      platform_set_drvdata(pdev, NULL);
-+      return 0;
-+}
-+
-+static struct platform_driver ehci_hcd_bcm63xx_driver = {
-+      .probe          = ehci_hcd_bcm63xx_drv_probe,
-+      .remove         = __devexit_p(ehci_hcd_bcm63xx_drv_remove),
-+      .shutdown       = usb_hcd_platform_shutdown,
-+      .driver         = {
-+              .name   = "bcm63xx_ehci",
-+              .owner  = THIS_MODULE,
-+      },
-+};
-+
-+MODULE_ALIAS("platform:bcm63xx_ehci");
---- a/drivers/usb/host/ehci-hcd.c
-+++ b/drivers/usb/host/ehci-hcd.c
-@@ -1229,6 +1229,11 @@ MODULE_LICENSE ("GPL");
- #define PLATFORM_DRIVER               ehci_octeon_driver
- #endif
-+#ifdef CONFIG_BCM63XX
-+#include "ehci-bcm63xx.c"
-+#define PLATFORM_DRIVER               ehci_hcd_bcm63xx_driver
-+#endif
-+
- #if !defined(PCI_DRIVER) && !defined(PLATFORM_DRIVER) && \
-     !defined(PS3_SYSTEM_BUS_DRIVER) && !defined(OF_PLATFORM_DRIVER) && \
-     !defined(XILINX_OF_PLATFORM_DRIVER)
diff --git a/target/linux/brcm63xx/patches-2.6.37/040-bcm963xx_flashmap.patch b/target/linux/brcm63xx/patches-2.6.37/040-bcm963xx_flashmap.patch
deleted file mode 100644 (file)
index daec181..0000000
+++ /dev/null
@@ -1,137 +0,0 @@
-From a4d005c91d403d9f3d0272db6cc46202c06ec774 Mon Sep 17 00:00:00 2001
-From: Axel Gembe <ago@bastart.eu.org>
-Date: Mon, 12 May 2008 18:54:09 +0200
-Subject: [PATCH] bcm963xx: flashmap support
-
-Signed-off-by: Axel Gembe <ago@bastart.eu.org>
----
- arch/mips/bcm63xx/boards/board_bcm963xx.c |   19 +----------------
- drivers/mtd/maps/bcm963xx-flash.c         |   32 ++++++++++++++++++++++++----
- drivers/mtd/redboot.c                     |   13 +++++++++--
- 3 files changed, 38 insertions(+), 26 deletions(-)
-
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -816,20 +816,6 @@ void __init board_setup(void)
-               panic("unexpected CPU for bcm963xx board");
- }
--static struct mtd_partition mtd_partitions[] = {
--      {
--              .name           = "cfe",
--              .offset         = 0x0,
--              .size           = 0x40000,
--      }
--};
--
--static struct physmap_flash_data flash_data = {
--      .width                  = 2,
--      .nr_parts               = ARRAY_SIZE(mtd_partitions),
--      .parts                  = mtd_partitions,
--};
--
- static struct resource mtd_resources[] = {
-       {
-               .start          = 0,    /* filled at runtime */
-@@ -839,12 +825,9 @@ static struct resource mtd_resources[] =
- };
- static struct platform_device mtd_dev = {
--      .name                   = "physmap-flash",
-+      .name                   = "bcm963xx-flash",
-       .resource               = mtd_resources,
-       .num_resources          = ARRAY_SIZE(mtd_resources),
--      .dev                    = {
--              .platform_data  = &flash_data,
--      },
- };
- static struct gpio_led_platform_data bcm63xx_led_data;
---- a/drivers/mtd/maps/bcm963xx-flash.c
-+++ b/drivers/mtd/maps/bcm963xx-flash.c
-@@ -27,6 +27,8 @@
- #include <linux/vmalloc.h>
- #include <linux/platform_device.h>
- #include <linux/io.h>
-+#include <linux/magic.h>
-+#include <linux/jffs2.h>
- #include <asm/mach-bcm63xx/bcm963xx_tag.h>
-@@ -35,6 +37,14 @@
- #define PFX KBUILD_MODNAME ": "
-+struct squashfs_super_block {
-+      __le32 s_magic;
-+      __le32 pad0[9];
-+      __le64 bytes_used;
-+};
-+
-+extern int parse_redboot_partitions(struct mtd_info *master, struct mtd_partition **pparts, unsigned long fis_origin);
-+
- static struct mtd_partition *parsed_parts;
- static struct mtd_info *bcm963xx_mtd_info;
-@@ -214,9 +224,21 @@ static int bcm963xx_probe(struct platfor
-                       }
-               }
-       } else {
--              dev_info(&pdev->dev, "unsupported bootloader\n");
--              err = -ENODEV;
--              goto err_probe;
-+              printk(KERN_INFO PFX "assuming RedBoot bootloader\n");
-+              if (bcm963xx_mtd_info->size > 0x00400000) {
-+                      printk(KERN_INFO PFX "Support for extended flash memory size : 0x%lx ; ONLY 64MBIT SUPPORT\n", bcm963xx_mtd_info->size);
-+                      bcm963xx_map.virt = (u32)(BCM63XX_EXTENDED_SIZE);
-+              }
-+
-+#ifdef CONFIG_MTD_REDBOOT_PARTS
-+              if (parsed_nr_parts == 0) {
-+                      int ret = parse_redboot_partitions(bcm963xx_mtd_info, &parsed_parts, 0);
-+                      if (ret > 0) {
-+                              part_type = "RedBoot";
-+                              parsed_nr_parts = ret;
-+                      }
-+              }
-+#endif
-       }
-       return add_mtd_partitions(bcm963xx_mtd_info, parsed_parts,
---- a/drivers/mtd/redboot.c
-+++ b/drivers/mtd/redboot.c
-@@ -57,7 +57,7 @@ static inline int redboot_checksum(struc
-       return 1;
- }
--static int parse_redboot_partitions(struct mtd_info *master,
-+int parse_redboot_partitions(struct mtd_info *master,
-                              struct mtd_partition **pparts,
-                              unsigned long fis_origin)
- {
-@@ -180,6 +180,14 @@ static int parse_redboot_partitions(stru
-               goto out;
-       }
-+      if (!fis_origin) {
-+              for (i = 0; i < numslots; i++) {
-+                      if (!strncmp(buf[i].name, "RedBoot", 8)) {
-+                              fis_origin = (buf[i].flash_base & (master->size << 1) - 1);
-+                      }
-+              }
-+      }
-+
-       for (i = 0; i < numslots; i++) {
-               struct fis_list *new_fl, **prev;
-@@ -202,9 +210,8 @@ static int parse_redboot_partitions(stru
-               new_fl->img = &buf[i];
-                 if (fis_origin) {
-                         buf[i].flash_base -= fis_origin;
--                } else {
--                        buf[i].flash_base &= master->size-1;
-                 }
-+              buf[i].flash_base &= (master->size << 1) - 1;
-               /* I'm sure the JFFS2 code has done me permanent damage.
-                * I now think the following is _normal_
diff --git a/target/linux/brcm63xx/patches-2.6.37/041-bcm963xx_real_rootfs_length.patch b/target/linux/brcm63xx/patches-2.6.37/041-bcm963xx_real_rootfs_length.patch
deleted file mode 100644 (file)
index dccd36f..0000000
+++ /dev/null
@@ -1,45 +0,0 @@
---- a/arch/mips/include/asm/mach-bcm63xx/bcm963xx_tag.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm963xx_tag.h
-@@ -86,8 +86,10 @@ struct bcm_tag {
-       char rootfs_crc[CRC_LEN];
-       /* 224-227: CRC32 of kernel partition */
-       char kernel_crc[CRC_LEN];
--      /* 228-235: Unused at present */
--      char reserved1[8];
-+      /* 228-231: Image sequence number */
-+      char image_sequence[4];
-+      /* 222-235: Openwrt: real rootfs length */
-+      char real_rootfs_length[4];
-       /* 236-239: CRC32 of header excluding tagVersion */
-       char header_crc[CRC_LEN];
-       /* 240-255: Unused at present */
---- a/drivers/mtd/maps/bcm963xx-flash.c
-+++ b/drivers/mtd/maps/bcm963xx-flash.c
-@@ -64,7 +64,7 @@ static int parse_cfe_partitions(struct m
-       int ret;
-       size_t retlen;
-       unsigned int rootfsaddr, kerneladdr, spareaddr;
--      unsigned int rootfslen, kernellen, sparelen, totallen;
-+      unsigned int rootfslen, kernellen, sparelen;
-       int namelen = 0;
-       int i;
-       char *boardid;
-@@ -85,7 +85,7 @@ static int parse_cfe_partitions(struct m
-       sscanf(buf->kernel_address, "%u", &kerneladdr);
-       sscanf(buf->kernel_length, "%u", &kernellen);
--      sscanf(buf->total_length, "%u", &totallen);
-+      rootfslen = *(uint32_t *)(&(buf->real_rootfs_length));
-       tagversion = &(buf->tag_version[0]);
-       boardid = &(buf->board_id[0]);
-@@ -94,7 +94,8 @@ static int parse_cfe_partitions(struct m
-       kerneladdr = kerneladdr - BCM63XX_EXTENDED_SIZE;
-       rootfsaddr = kerneladdr + kernellen;
--      spareaddr = roundup(totallen, master->erasesize) + master->erasesize;
-+      rootfslen = roundup(rootfslen, master->erasesize);
-+      spareaddr = rootfsaddr + rootfslen;
-       sparelen = master->size - spareaddr - master->erasesize;
-       rootfslen = spareaddr - rootfsaddr;
diff --git a/target/linux/brcm63xx/patches-2.6.37/070_bcm63xx_enet_vlan_incoming_fixed.patch b/target/linux/brcm63xx/patches-2.6.37/070_bcm63xx_enet_vlan_incoming_fixed.patch
deleted file mode 100644 (file)
index 8211e29..0000000
+++ /dev/null
@@ -1,11 +0,0 @@
---- a/drivers/net/bcm63xx_enet.c
-+++ b/drivers/net/bcm63xx_enet.c
-@@ -1515,7 +1515,7 @@ static int compute_hw_mtu(struct bcm_ene
-       actual_mtu = mtu;
-       /* add ethernet header + vlan tag size */
--      actual_mtu += VLAN_ETH_HLEN;
-+      actual_mtu += VLAN_ETH_HLEN + VLAN_HLEN;
-       if (actual_mtu < 64 || actual_mtu > BCMENET_MAX_MTU)
-               return -EINVAL;
diff --git a/target/linux/brcm63xx/patches-2.6.37/080-bcm6345_enet.patch b/target/linux/brcm63xx/patches-2.6.37/080-bcm6345_enet.patch
deleted file mode 100644 (file)
index d99ac5a..0000000
+++ /dev/null
@@ -1,530 +0,0 @@
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -29,16 +29,15 @@
-                                       CKCTL_6338_SAR_EN |             \
-                                       CKCTL_6338_SPI_EN)
--#define CKCTL_6345_CPU_EN             (1 << 0)
--#define CKCTL_6345_BUS_EN             (1 << 1)
--#define CKCTL_6345_EBI_EN             (1 << 2)
--#define CKCTL_6345_UART_EN            (1 << 3)
--#define CKCTL_6345_ADSLPHY_EN         (1 << 4)
--#define CKCTL_6345_ENET_EN            (1 << 7)
--#define CKCTL_6345_USBH_EN            (1 << 8)
-+#define CKCTL_6345_CPU_EN             (1 << 16)
-+#define CKCTL_6345_BUS_EN             (1 << 17)
-+#define CKCTL_6345_EBI_EN             (1 << 18)
-+#define CKCTL_6345_UART_EN            (1 << 19)
-+#define CKCTL_6345_ADSLPHY_EN         (1 << 20)
-+#define CKCTL_6345_ENET_EN            (1 << 23)
-+#define CKCTL_6345_USBH_EN            (1 << 24)
--#define CKCTL_6345_ALL_SAFE_EN                (CKCTL_6345_ENET_EN |   \
--                                      CKCTL_6345_USBH_EN |    \
-+#define CKCTL_6345_ALL_SAFE_EN                (CKCTL_6345_USBH_EN |   \
-                                       CKCTL_6345_ADSLPHY_EN)
- #define CKCTL_6348_ADSLPHY_EN         (1 << 0)
-@@ -548,6 +547,39 @@
- #define ENETDMA_SRAM4_REG(x)          (0x20c + (x) * 0x10)
-+/* Broadcom 6345 ENET DMA definitions */
-+#define ENETDMA_6345_CHANCFG_REG(x)   (0x00 + (x) * 0x40)
-+#define ENETDMA_6345_CHANCFG_EN_SHIFT 0
-+#define ENETDMA_6345_CHANCFG_EN_MASK  (1 << ENETDMA_6345_CHANCFG_EN_SHIFT)
-+#define ENETDMA_6345_PKTHALT_SHIFT    1
-+#define ENETDMA_6345_PKTHALT_MASK     (1 << ENETDMA_6345_PKTHALT_SHIFT)
-+#define ENETDMA_6345_CHAINING_SHIFT   2
-+#define ENETDMA_6345_CHAINING_MASK    (1 << ENETDMA_6345_CHAINING_SHIFT)
-+#define ENETDMA_6345_WRAP_EN_SHIFT    3
-+#define ENETDMA_6345_WRAP_EN_MASK     (1 << ENETDMA_6345_WRAP_EN_SHIFT)
-+#define ENETDMA_6345_FLOWC_EN_SHIFT   4
-+#define ENETDMA_6345_FLOWC_EN_MASK    (1 << ENETDMA_6345_FLOWC_EN_SHIFT)
-+
-+#define ENETDMA_6345_MAXBURST_REG(x)  (0x04 + (x) * 0x40)
-+
-+#define ENETDMA_6345_RSTART_REG(x)    (0x08 + (x) * 0x40)
-+
-+#define ENETDMA_6345_LEN_REG(x)               (0x0C + (x) * 0x40)
-+
-+#define ENETDMA_6345_BSTAT_REG(x)     (0x10 + (x) * 0x40)
-+
-+#define ENETDMA_6345_IR_REG(x)                (0x14 + (x) * 0x40)
-+#define ENETDMA_6345_IR_BUFDONE_MASK  (1 << 0)
-+#define ENETDMA_6345_IR_PKTDONE_MASK  (1 << 1)
-+#define ENETDMA_6345_IR_NOTOWNER_MASK (1 << 2)
-+
-+#define ENETDMA_6345_IRMASK_REG(x)    (0x18 + (x) * 0x40)
-+
-+#define ENETDMA_6345_FC_REG(x)                (0x1C + (x) * 0x40)
-+
-+#define ENETDMA_6345_BUFALLOC_REG(x)  (0x20 + (x) * 0x40)
-+
-+
- /*************************************************************************
-  * _REG relative to RSET_OHCI_PRIV
-  *************************************************************************/
---- a/drivers/net/bcm63xx_enet.c
-+++ b/drivers/net/bcm63xx_enet.c
-@@ -31,6 +31,7 @@
- #include <linux/if_vlan.h>
- #include <bcm63xx_dev_enet.h>
-+#include <bcm63xx_cpu.h>
- #include "bcm63xx_enet.h"
- static char bcm_enet_driver_name[] = "bcm63xx_enet";
-@@ -177,6 +178,7 @@ static void bcm_enet_mdio_write_mii(stru
- static int bcm_enet_refill_rx(struct net_device *dev)
- {
-       struct bcm_enet_priv *priv;
-+      unsigned int desc_shift = BCMCPU_IS_6345() ? DMADESC_6345_SHIFT : 0;
-       priv = netdev_priv(dev);
-@@ -205,7 +207,7 @@ static int bcm_enet_refill_rx(struct net
-               len_stat = priv->rx_skb_size << DMADESC_LENGTH_SHIFT;
-               len_stat |= DMADESC_OWNER_MASK;
-               if (priv->rx_dirty_desc == priv->rx_ring_size - 1) {
--                      len_stat |= DMADESC_WRAP_MASK;
-+                      len_stat |= (DMADESC_WRAP_MASK >> desc_shift);
-                       priv->rx_dirty_desc = 0;
-               } else {
-                       priv->rx_dirty_desc++;
-@@ -216,7 +218,10 @@ static int bcm_enet_refill_rx(struct net
-               priv->rx_desc_count++;
-               /* tell dma engine we allocated one buffer */
--              enet_dma_writel(priv, 1, ENETDMA_BUFALLOC_REG(priv->rx_chan));
-+              if (!BCMCPU_IS_6345())
-+                      enet_dma_writel(priv, 1, ENETDMA_BUFALLOC_REG(priv->rx_chan));
-+              else
-+                      enet_dma_writel(priv, 1, ENETDMA_6345_BUFALLOC_REG(priv->rx_chan));
-       }
-       /* If rx ring is still empty, set a timer to try allocating
-@@ -254,6 +259,7 @@ static int bcm_enet_receive_queue(struct
-       struct bcm_enet_priv *priv;
-       struct device *kdev;
-       int processed;
-+      unsigned int desc_shift = BCMCPU_IS_6345() ? DMADESC_6345_SHIFT : 0;
-       priv = netdev_priv(dev);
-       kdev = &priv->pdev->dev;
-@@ -292,7 +298,7 @@ static int bcm_enet_receive_queue(struct
-               /* if the packet does not have start of packet _and_
-                * end of packet flag set, then just recycle it */
--              if ((len_stat & DMADESC_ESOP_MASK) != DMADESC_ESOP_MASK) {
-+              if ((len_stat & (DMADESC_ESOP_MASK >> desc_shift)) != (DMADESC_ESOP_MASK >> desc_shift)) {
-                       dev->stats.rx_dropped++;
-                       continue;
-               }
-@@ -352,8 +358,15 @@ static int bcm_enet_receive_queue(struct
-               bcm_enet_refill_rx(dev);
-               /* kick rx dma */
--              enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK,
--                              ENETDMA_CHANCFG_REG(priv->rx_chan));
-+              if (!BCMCPU_IS_6345())
-+                      enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK,
-+                                      ENETDMA_CHANCFG_REG(priv->rx_chan));
-+              else
-+                      enet_dma_writel(priv, ENETDMA_6345_CHANCFG_EN_MASK |
-+                                            ENETDMA_6345_CHAINING_MASK |
-+                                            ENETDMA_6345_WRAP_EN_MASK |
-+                                            ENETDMA_6345_FLOWC_EN_MASK,
-+                                      ENETDMA_6345_CHANCFG_REG(priv->rx_chan));
-       }
-       return processed;
-@@ -428,10 +441,21 @@ static int bcm_enet_poll(struct napi_str
-       dev = priv->net_dev;
-       /* ack interrupts */
--      enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
--                      ENETDMA_IR_REG(priv->rx_chan));
--      enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
--                      ENETDMA_IR_REG(priv->tx_chan));
-+      if (!BCMCPU_IS_6345()) {
-+              enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
-+                              ENETDMA_IR_REG(priv->rx_chan));
-+              enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
-+                              ENETDMA_IR_REG(priv->tx_chan));
-+      } else {
-+              enet_dma_writel(priv, ENETDMA_IR_BUFDONE_MASK |
-+                                      ENETDMA_IR_PKTDONE_MASK |
-+                                      ENETDMA_IR_NOTOWNER_MASK,
-+                              ENETDMA_6345_IR_REG(priv->rx_chan));
-+              enet_dma_writel(priv, ENETDMA_IR_BUFDONE_MASK |
-+                                      ENETDMA_IR_PKTDONE_MASK |
-+                                      ENETDMA_IR_NOTOWNER_MASK,
-+                              ENETDMA_6345_IR_REG(priv->tx_chan));
-+      }
-       /* reclaim sent skb */
-       tx_work_done = bcm_enet_tx_reclaim(dev, 0);
-@@ -450,10 +474,21 @@ static int bcm_enet_poll(struct napi_str
-       napi_complete(napi);
-       /* restore rx/tx interrupt */
--      enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
--                      ENETDMA_IRMASK_REG(priv->rx_chan));
--      enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
--                      ENETDMA_IRMASK_REG(priv->tx_chan));
-+      if (!BCMCPU_IS_6345()) {
-+              enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
-+                              ENETDMA_IRMASK_REG(priv->rx_chan));
-+              enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
-+                              ENETDMA_IRMASK_REG(priv->tx_chan));
-+      } else {
-+              enet_dma_writel(priv, ENETDMA_IR_BUFDONE_MASK |
-+                                      ENETDMA_IR_PKTDONE_MASK |
-+                                      ENETDMA_IR_NOTOWNER_MASK,
-+                              ENETDMA_6345_IRMASK_REG(priv->rx_chan));
-+              enet_dma_writel(priv, ENETDMA_IR_BUFDONE_MASK |
-+                                      ENETDMA_IR_PKTDONE_MASK |
-+                                      ENETDMA_IR_NOTOWNER_MASK,
-+                              ENETDMA_6345_IRMASK_REG(priv->tx_chan));
-+      }
-       return rx_work_done;
- }
-@@ -496,8 +531,13 @@ static irqreturn_t bcm_enet_isr_dma(int
-       priv = netdev_priv(dev);
-       /* mask rx/tx interrupts */
--      enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan));
--      enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan));
-+      if (!BCMCPU_IS_6345()) {
-+              enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan));
-+              enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan));
-+      } else {
-+              enet_dma_writel(priv, 0, ENETDMA_6345_IRMASK_REG(priv->rx_chan));
-+              enet_dma_writel(priv, 0, ENETDMA_6345_IRMASK_REG(priv->tx_chan));
-+      }
-       napi_schedule(&priv->napi);
-@@ -513,6 +553,7 @@ static int bcm_enet_start_xmit(struct sk
-       struct bcm_enet_desc *desc;
-       u32 len_stat;
-       int ret;
-+      unsigned int desc_shift = BCMCPU_IS_6345() ? DMADESC_6345_SHIFT : 0;
-       priv = netdev_priv(dev);
-@@ -538,14 +579,13 @@ static int bcm_enet_start_xmit(struct sk
-                                      DMA_TO_DEVICE);
-       len_stat = (skb->len << DMADESC_LENGTH_SHIFT) & DMADESC_LENGTH_MASK;
--      len_stat |= DMADESC_ESOP_MASK |
--              DMADESC_APPEND_CRC |
--              DMADESC_OWNER_MASK;
-+      len_stat |= ((DMADESC_ESOP_MASK >> desc_shift) |
-+                  DMADESC_APPEND_CRC | DMADESC_OWNER_MASK);
-       priv->tx_curr_desc++;
-       if (priv->tx_curr_desc == priv->tx_ring_size) {
-               priv->tx_curr_desc = 0;
--              len_stat |= DMADESC_WRAP_MASK;
-+              len_stat |= (DMADESC_WRAP_MASK >> desc_shift);
-       }
-       priv->tx_desc_count--;
-@@ -556,8 +596,15 @@ static int bcm_enet_start_xmit(struct sk
-       wmb();
-       /* kick tx dma */
--      enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK,
--                      ENETDMA_CHANCFG_REG(priv->tx_chan));
-+      if (!BCMCPU_IS_6345())
-+              enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK,
-+                              ENETDMA_CHANCFG_REG(priv->tx_chan));
-+      else
-+              enet_dma_writel(priv, ENETDMA_6345_CHANCFG_EN_MASK |
-+                                      ENETDMA_6345_CHAINING_MASK |
-+                                      ENETDMA_6345_WRAP_EN_MASK |
-+                                      ENETDMA_6345_FLOWC_EN_MASK,
-+                              ENETDMA_6345_CHANCFG_REG(priv->tx_chan));
-       /* stop queue if no more desc available */
-       if (!priv->tx_desc_count)
-@@ -685,6 +732,9 @@ static void bcm_enet_set_flow(struct bcm
-               val &= ~ENET_RXCFG_ENFLOW_MASK;
-       enet_writel(priv, val, ENET_RXCFG_REG);
-+      if (BCMCPU_IS_6345())
-+              return;
-+
-       /* tx flow control (pause frame generation) */
-       val = enet_dma_readl(priv, ENETDMA_CFG_REG);
-       if (tx_en)
-@@ -832,8 +882,13 @@ static int bcm_enet_open(struct net_devi
-       /* mask all interrupts and request them */
-       enet_writel(priv, 0, ENET_IRMASK_REG);
--      enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan));
--      enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan));
-+      if (!BCMCPU_IS_6345()) {
-+              enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan));
-+              enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan));
-+      } else {
-+              enet_dma_writel(priv, 0, ENETDMA_6345_IRMASK_REG(priv->rx_chan));
-+              enet_dma_writel(priv, 0, ENETDMA_6345_IRMASK_REG(priv->tx_chan));
-+      }
-       ret = request_irq(dev->irq, bcm_enet_isr_mac, 0, dev->name, dev);
-       if (ret)
-@@ -912,8 +967,12 @@ static int bcm_enet_open(struct net_devi
-       priv->rx_curr_desc = 0;
-       /* initialize flow control buffer allocation */
--      enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0,
--                      ENETDMA_BUFALLOC_REG(priv->rx_chan));
-+      if (!BCMCPU_IS_6345())
-+              enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0,
-+                              ENETDMA_BUFALLOC_REG(priv->rx_chan));
-+      else
-+              enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0,
-+                              ENETDMA_6345_BUFALLOC_REG(priv->rx_chan));
-       if (bcm_enet_refill_rx(dev)) {
-               dev_err(kdev, "cannot allocate rx skb queue\n");
-@@ -922,37 +981,62 @@ static int bcm_enet_open(struct net_devi
-       }
-       /* write rx & tx ring addresses */
--      enet_dma_writel(priv, priv->rx_desc_dma,
--                      ENETDMA_RSTART_REG(priv->rx_chan));
--      enet_dma_writel(priv, priv->tx_desc_dma,
--                      ENETDMA_RSTART_REG(priv->tx_chan));
-+      if (!BCMCPU_IS_6345()) {
-+              enet_dma_writel(priv, priv->rx_desc_dma,
-+                              ENETDMA_RSTART_REG(priv->rx_chan));
-+              enet_dma_writel(priv, priv->tx_desc_dma,
-+                              ENETDMA_RSTART_REG(priv->tx_chan));
-+      } else {
-+              enet_dma_writel(priv, priv->rx_desc_dma,
-+                              ENETDMA_6345_RSTART_REG(priv->rx_chan));
-+              enet_dma_writel(priv, priv->tx_desc_dma,
-+                              ENETDMA_6345_RSTART_REG(priv->tx_chan));
-+      }
-       /* clear remaining state ram for rx & tx channel */
--      enet_dma_writel(priv, 0, ENETDMA_SRAM2_REG(priv->rx_chan));
--      enet_dma_writel(priv, 0, ENETDMA_SRAM2_REG(priv->tx_chan));
--      enet_dma_writel(priv, 0, ENETDMA_SRAM3_REG(priv->rx_chan));
--      enet_dma_writel(priv, 0, ENETDMA_SRAM3_REG(priv->tx_chan));
--      enet_dma_writel(priv, 0, ENETDMA_SRAM4_REG(priv->rx_chan));
--      enet_dma_writel(priv, 0, ENETDMA_SRAM4_REG(priv->tx_chan));
-+      if (!BCMCPU_IS_6345()) {
-+              enet_dma_writel(priv, 0, ENETDMA_SRAM2_REG(priv->rx_chan));
-+              enet_dma_writel(priv, 0, ENETDMA_SRAM2_REG(priv->tx_chan));
-+              enet_dma_writel(priv, 0, ENETDMA_SRAM3_REG(priv->rx_chan));
-+              enet_dma_writel(priv, 0, ENETDMA_SRAM3_REG(priv->tx_chan));
-+              enet_dma_writel(priv, 0, ENETDMA_SRAM4_REG(priv->rx_chan));
-+              enet_dma_writel(priv, 0, ENETDMA_SRAM4_REG(priv->tx_chan));
-+      } else {
-+              enet_dma_writel(priv, 0, ENETDMA_6345_FC_REG(priv->rx_chan));
-+              enet_dma_writel(priv, 0, ENETDMA_6345_FC_REG(priv->tx_chan));
-+      }
-       /* set max rx/tx length */
-       enet_writel(priv, priv->hw_mtu, ENET_RXMAXLEN_REG);
-       enet_writel(priv, priv->hw_mtu, ENET_TXMAXLEN_REG);
-       /* set dma maximum burst len */
--      enet_dma_writel(priv, BCMENET_DMA_MAXBURST,
--                      ENETDMA_MAXBURST_REG(priv->rx_chan));
--      enet_dma_writel(priv, BCMENET_DMA_MAXBURST,
--                      ENETDMA_MAXBURST_REG(priv->tx_chan));
-+      if (!BCMCPU_IS_6345()) {
-+              enet_dma_writel(priv, BCMENET_DMA_MAXBURST,
-+                              ENETDMA_MAXBURST_REG(priv->rx_chan));
-+              enet_dma_writel(priv, BCMENET_DMA_MAXBURST,
-+                              ENETDMA_MAXBURST_REG(priv->tx_chan));
-+      } else {
-+              enet_dma_writel(priv, BCMENET_DMA_MAXBURST,
-+                              ENETDMA_6345_MAXBURST_REG(priv->rx_chan));
-+              enet_dma_writel(priv, BCMENET_DMA_MAXBURST,
-+                              ENETDMA_6345_MAXBURST_REG(priv->tx_chan));
-+      }
-       /* set correct transmit fifo watermark */
-       enet_writel(priv, BCMENET_TX_FIFO_TRESH, ENET_TXWMARK_REG);
-       /* set flow control low/high threshold to 1/3 / 2/3 */
--      val = priv->rx_ring_size / 3;
--      enet_dma_writel(priv, val, ENETDMA_FLOWCL_REG(priv->rx_chan));
--      val = (priv->rx_ring_size * 2) / 3;
--      enet_dma_writel(priv, val, ENETDMA_FLOWCH_REG(priv->rx_chan));
-+      if (!BCMCPU_IS_6345()) {
-+              val = priv->rx_ring_size / 3;
-+              enet_dma_writel(priv, val, ENETDMA_FLOWCL_REG(priv->rx_chan));
-+              val = (priv->rx_ring_size * 2) / 3;
-+              enet_dma_writel(priv, val, ENETDMA_FLOWCH_REG(priv->rx_chan));
-+      } else {
-+              enet_dma_writel(priv, 5, ENETDMA_6345_FC_REG(priv->rx_chan));
-+              enet_dma_writel(priv, priv->rx_ring_size, ENETDMA_6345_LEN_REG(priv->rx_chan));
-+              enet_dma_writel(priv, priv->tx_ring_size, ENETDMA_6345_LEN_REG(priv->tx_chan));
-+      }
-       /* all set, enable mac and interrupts, start dma engine and
-        * kick rx dma channel */
-@@ -960,27 +1044,58 @@ static int bcm_enet_open(struct net_devi
-       val = enet_readl(priv, ENET_CTL_REG);
-       val |= ENET_CTL_ENABLE_MASK;
-       enet_writel(priv, val, ENET_CTL_REG);
--      enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG);
--      enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK,
--                      ENETDMA_CHANCFG_REG(priv->rx_chan));
-+
-+      if (!BCMCPU_IS_6345()) {
-+              enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG);
-+              enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK,
-+                              ENETDMA_CHANCFG_REG(priv->rx_chan));
-+      } else {
-+              enet_dma_writel(priv, ENETDMA_6345_CHANCFG_EN_MASK |
-+                                      ENETDMA_6345_CHAINING_MASK |
-+                                      ENETDMA_6345_WRAP_EN_MASK |
-+                                      ENETDMA_6345_FLOWC_EN_MASK,
-+                              ENETDMA_6345_CHANCFG_REG(priv->rx_chan));
-+      }
-       /* watch "mib counters about to overflow" interrupt */
-       enet_writel(priv, ENET_IR_MIB, ENET_IR_REG);
-       enet_writel(priv, ENET_IR_MIB, ENET_IRMASK_REG);
-       /* watch "packet transferred" interrupt in rx and tx */
--      enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
--                      ENETDMA_IR_REG(priv->rx_chan));
--      enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
--                      ENETDMA_IR_REG(priv->tx_chan));
-+      if (!BCMCPU_IS_6345()) {
-+              enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
-+                              ENETDMA_IR_REG(priv->rx_chan));
-+              enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
-+                              ENETDMA_IR_REG(priv->tx_chan));
-+      } else {
-+              enet_dma_writel(priv, ENETDMA_IR_BUFDONE_MASK |
-+                                      ENETDMA_IR_PKTDONE_MASK |
-+                                      ENETDMA_IR_NOTOWNER_MASK,
-+                              ENETDMA_6345_IR_REG(priv->rx_chan));
-+              enet_dma_writel(priv, ENETDMA_IR_BUFDONE_MASK |
-+                                      ENETDMA_IR_PKTDONE_MASK |
-+                                      ENETDMA_IR_NOTOWNER_MASK,
-+                              ENETDMA_6345_IR_REG(priv->tx_chan));
-+      }
-       /* make sure we enable napi before rx interrupt  */
-       napi_enable(&priv->napi);
--      enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
--                      ENETDMA_IRMASK_REG(priv->rx_chan));
--      enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
--                      ENETDMA_IRMASK_REG(priv->tx_chan));
-+      if (!BCMCPU_IS_6345()) {
-+              enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
-+                              ENETDMA_IRMASK_REG(priv->rx_chan));
-+              enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
-+                              ENETDMA_IRMASK_REG(priv->tx_chan));
-+      } else {
-+              enet_dma_writel(priv, ENETDMA_IR_BUFDONE_MASK |
-+                                      ENETDMA_IR_PKTDONE_MASK |
-+                                      ENETDMA_IR_NOTOWNER_MASK,
-+                              ENETDMA_6345_IRMASK_REG(priv->rx_chan));
-+              enet_dma_writel(priv, ENETDMA_IR_BUFDONE_MASK |
-+                                      ENETDMA_IR_PKTDONE_MASK |
-+                                      ENETDMA_IR_NOTOWNER_MASK,
-+                              ENETDMA_6345_IRMASK_REG(priv->tx_chan));
-+      }
-       if (priv->has_phy)
-               phy_start(priv->phydev);
-@@ -1060,13 +1175,19 @@ static void bcm_enet_disable_dma(struct
- {
-       int limit;
--      enet_dma_writel(priv, 0, ENETDMA_CHANCFG_REG(chan));
-+      if (!BCMCPU_IS_6345())
-+              enet_dma_writel(priv, 0, ENETDMA_CHANCFG_REG(chan));
-+      else
-+              enet_dma_writel(priv, 0, ENETDMA_6345_CHANCFG_REG(chan));
-       limit = 1000;
-       do {
-               u32 val;
--              val = enet_dma_readl(priv, ENETDMA_CHANCFG_REG(chan));
-+              if (!BCMCPU_IS_6345())
-+                      val = enet_dma_readl(priv, ENETDMA_CHANCFG_REG(chan));
-+              else
-+                      val = enet_dma_readl(priv, ENETDMA_6345_CHANCFG_REG(chan));
-               if (!(val & ENETDMA_CHANCFG_EN_MASK))
-                       break;
-               udelay(1);
-@@ -1093,8 +1214,13 @@ static int bcm_enet_stop(struct net_devi
-       /* mask all interrupts */
-       enet_writel(priv, 0, ENET_IRMASK_REG);
--      enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan));
--      enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan));
-+      if (!BCMCPU_IS_6345()) {
-+              enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan));
-+              enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan));
-+      } else {
-+              enet_dma_writel(priv, 0, ENETDMA_6345_IRMASK_REG(priv->rx_chan));
-+              enet_dma_writel(priv, 0, ENETDMA_6345_IRMASK_REG(priv->tx_chan));
-+      }
-       /* make sure no mib update is scheduled */
-       flush_scheduled_work();
-@@ -1622,6 +1748,7 @@ static int __devinit bcm_enet_probe(stru
-       const char *clk_name;
-       unsigned int iomem_size;
-       int i, ret;
-+      unsigned int chan_offset = 0;
-       /* stop if shared driver failed, assume driver->probe will be
-        * called in the same order we register devices (correct ?) */
-@@ -1661,10 +1788,13 @@ static int __devinit bcm_enet_probe(stru
-       priv->irq_tx = res_irq_tx->start;
-       priv->mac_id = pdev->id;
-+      if (BCMCPU_IS_6345())
-+              chan_offset = 1;
-+
-       /* get rx & tx dma channel id for this mac */
-       if (priv->mac_id == 0) {
--              priv->rx_chan = 0;
--              priv->tx_chan = 1;
-+              priv->rx_chan = 0 + chan_offset;
-+              priv->tx_chan = 1 + chan_offset;
-               clk_name = "enet0";
-       } else {
-               priv->rx_chan = 2;
---- a/drivers/net/bcm63xx_enet.h
-+++ b/drivers/net/bcm63xx_enet.h
-@@ -46,6 +46,9 @@ struct bcm_enet_desc {
- #define DMADESC_ESOP_MASK     (DMADESC_EOP_MASK | DMADESC_SOP_MASK)
- #define DMADESC_WRAP_MASK     (1 << 12)
-+/* Shift down for EOP, SOP and WRAP bits */
-+#define DMADESC_6345_SHIFT    (3)
-+
- #define DMADESC_UNDER_MASK    (1 << 9)
- #define DMADESC_APPEND_CRC    (1 << 8)
- #define DMADESC_OVSIZE_MASK   (1 << 4)
---- a/arch/mips/bcm63xx/dev-enet.c
-+++ b/arch/mips/bcm63xx/dev-enet.c
-@@ -104,7 +104,7 @@ int __init bcm63xx_enet_register(int uni
-       if (unit > 1)
-               return -ENODEV;
--      if (unit == 1 && BCMCPU_IS_6338())
-+      if (unit == 1 && (BCMCPU_IS_6338() || BCMCPU_IS_6345()))
-               return -ENODEV;
-       if (!shared_device_registered) {
diff --git a/target/linux/brcm63xx/patches-2.6.37/100-reset_buttons.patch b/target/linux/brcm63xx/patches-2.6.37/100-reset_buttons.patch
deleted file mode 100644 (file)
index 786c18b..0000000
+++ /dev/null
@@ -1,98 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -15,6 +15,8 @@
- #include <linux/mtd/partitions.h>
- #include <linux/mtd/physmap.h>
- #include <linux/ssb/ssb.h>
-+#include <linux/gpio_buttons.h>
-+#include <linux/input.h>
- #include <asm/addrspace.h>
- #include <bcm63xx_board.h>
- #include <bcm63xx_cpu.h>
-@@ -296,6 +298,16 @@ static struct board_info __initdata boar
-                       .active_low     = 1,
-               },
-       },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 33,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
- };
- static struct board_info __initdata board_96348gw = {
-@@ -354,6 +366,16 @@ static struct board_info __initdata boar
-                       .active_low     = 1,
-               },
-       },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 36,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
- };
- static struct board_info __initdata board_FAST2404 = {
-@@ -838,12 +860,23 @@ static struct platform_device bcm63xx_gp
-       .dev.platform_data      = &bcm63xx_led_data,
- };
-+static struct gpio_buttons_platform_data bcm63xx_gpio_buttons_data = {
-+      .poll_interval  = 20,
-+};
-+
-+static struct platform_device bcm63xx_gpio_buttons_device = {
-+      .name           = "gpio-buttons",
-+      .id             = 0,
-+      .dev.platform_data = &bcm63xx_gpio_buttons_data,
-+};
-+
- /*
-  * third stage init callback, register all board devices.
-  */
- int __init board_register_devices(void)
- {
-       u32 val;
-+      int button_count = 0;
-       if (board.has_uart0)
-               bcm63xx_uart_register(0);
-@@ -888,5 +921,16 @@ int __init board_register_devices(void)
-       platform_device_register(&bcm63xx_gpio_leds);
-+      /* count number of BUTTONs defined by this device */
-+      while (button_count < ARRAY_SIZE(board.buttons) && board.buttons[button_count].desc)
-+              button_count++;
-+
-+      if (button_count) {
-+              bcm63xx_gpio_buttons_data.nbuttons = button_count;
-+              bcm63xx_gpio_buttons_data.buttons = board.buttons;
-+
-+              platform_device_register(&bcm63xx_gpio_buttons_device);
-+      }
-+
-       return 0;
- }
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -57,6 +57,9 @@ struct board_info {
-       /* GPIO LEDs */
-       struct gpio_led leds[5];
-+
-+      /* Buttons */
-+      struct gpio_button buttons[2];
- };
- #endif /* ! BOARD_BCM963XX_H_ */
diff --git a/target/linux/brcm63xx/patches-2.6.37/110-gpiodev.patch b/target/linux/brcm63xx/patches-2.6.37/110-gpiodev.patch
deleted file mode 100644 (file)
index fc99f53..0000000
+++ /dev/null
@@ -1,22 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -852,6 +852,10 @@ static struct platform_device mtd_dev =
-       .num_resources          = ARRAY_SIZE(mtd_resources),
- };
-+static struct resource gpiodev_resource = {
-+      .start                  = 0xFFFFFFFF,
-+};
-+
- static struct gpio_led_platform_data bcm63xx_led_data;
- static struct platform_device bcm63xx_gpio_leds = {
-@@ -916,6 +920,8 @@ int __init board_register_devices(void)
-       platform_device_register(&mtd_dev);
-+      platform_device_register_simple("GPIODEV", 0, &gpiodev_resource, 1);
-+
-       bcm63xx_led_data.num_leds = ARRAY_SIZE(board.leds);
-       bcm63xx_led_data.leds = board.leds;
diff --git a/target/linux/brcm63xx/patches-2.6.37/141-led_count.patch b/target/linux/brcm63xx/patches-2.6.37/141-led_count.patch
deleted file mode 100644 (file)
index baf0920..0000000
+++ /dev/null
@@ -1,23 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -881,6 +881,7 @@ int __init board_register_devices(void)
- {
-       u32 val;
-       int button_count = 0;
-+      int led_count = 0;
-       if (board.has_uart0)
-               bcm63xx_uart_register(0);
-@@ -922,7 +923,11 @@ int __init board_register_devices(void)
-       platform_device_register_simple("GPIODEV", 0, &gpiodev_resource, 1);
--      bcm63xx_led_data.num_leds = ARRAY_SIZE(board.leds);
-+      /* count number of LEDs defined by this device */
-+      while (led_count < ARRAY_SIZE(board.leds) && board.leds[led_count].name)
-+        led_count++;
-+
-+      bcm63xx_led_data.num_leds = led_count;
-       bcm63xx_led_data.leds = board.leds;
-       platform_device_register(&bcm63xx_gpio_leds);
diff --git a/target/linux/brcm63xx/patches-2.6.37/180-udc_preliminary_support.patch b/target/linux/brcm63xx/patches-2.6.37/180-udc_preliminary_support.patch
deleted file mode 100644 (file)
index 7b341b7..0000000
+++ /dev/null
@@ -1,243 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -29,6 +29,7 @@
- #include <bcm63xx_dev_pcmcia.h>
- #include <bcm63xx_dev_usb_ohci.h>
- #include <bcm63xx_dev_usb_ehci.h>
-+#include <bcm63xx_dev_usb_udc.h>
- #include <board_bcm963xx.h>
- #define PFX   "board_bcm963xx: "
-@@ -400,6 +401,8 @@ static struct board_info __initdata boar
-       .has_ohci0                      = 1,
-       .has_pccard                     = 1,
-       .has_ehci0                      = 1,
-+
-+      .has_udc0                       = 1,
- };
- static struct board_info __initdata board_rta1025w_16 = {
-@@ -909,6 +912,9 @@ int __init board_register_devices(void)
-       if (board.has_dsp)
-               bcm63xx_dsp_register(&board.dsp);
-+      if (board.has_udc0)
-+              bcm63xx_udc_register();
-+
-       /* read base address of boot chip select (0) */
-       if (BCMCPU_IS_6345())
-               val = 0x1fc00000;
---- /dev/null
-+++ b/arch/mips/bcm63xx/dev-usb-udc.c
-@@ -0,0 +1,58 @@
-+/*
-+ * Copyright (C) 2009 Henk Vergonet <Henk.Vergonet@gmail.com>
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License as
-+ * published by the Free Software Foundation; either version 2 of
-+ * the License, or (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
-+ */
-+#include <linux/init.h>
-+#include <linux/kernel.h>
-+#include <linux/platform_device.h>
-+#include <bcm63xx_cpu.h>
-+
-+static struct resource udc_resources[] = {
-+      {
-+              .start          = -1, /* filled at runtime */
-+              .end            = -1, /* filled at runtime */
-+              .flags          = IORESOURCE_MEM,
-+      },
-+      {
-+              .start          = -1, /* filled at runtime */
-+              .flags          = IORESOURCE_IRQ,
-+      },
-+};
-+
-+static u64 udc_dmamask = ~(u32)0;
-+
-+static struct platform_device bcm63xx_udc_device = {
-+      .name           = "bcm63xx-udc",
-+      .id             = 0,
-+      .num_resources  = ARRAY_SIZE(udc_resources),
-+      .resource       = udc_resources,
-+      .dev            = {
-+              .dma_mask               = &udc_dmamask,
-+              .coherent_dma_mask      = 0xffffffff,
-+      },
-+};
-+
-+int __init bcm63xx_udc_register(void)
-+{
-+      if (!BCMCPU_IS_6338() && !BCMCPU_IS_6345() && !BCMCPU_IS_6348())
-+              return 0;
-+
-+      udc_resources[0].start = bcm63xx_regset_address(RSET_UDC0);
-+      udc_resources[0].end = udc_resources[0].start;
-+      udc_resources[0].end += RSET_UDC_SIZE - 1;
-+      udc_resources[1].start = bcm63xx_get_irq_number(IRQ_UDC0);
-+      return platform_device_register(&bcm63xx_udc_device);
-+}
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-@@ -127,7 +127,7 @@ enum bcm63xx_regs_set {
- #define BCM_6338_UART1_BASE           (0xdeadbeef)
- #define BCM_6338_GPIO_BASE            (0xfffe0400)
- #define BCM_6338_SPI_BASE             (0xfffe0c00)
--#define BCM_6338_UDC0_BASE            (0xdeadbeef)
-+#define BCM_6338_UDC0_BASE            (0xfffe3000)
- #define BCM_6338_USBDMA_BASE          (0xfffe2400)
- #define BCM_6338_OHCI0_BASE           (0xdeadbeef)
- #define BCM_6338_OHCI_PRIV_BASE               (0xfffe3000)
-@@ -158,7 +158,7 @@ enum bcm63xx_regs_set {
- #define BCM_6345_UART1_BASE           (0xdeadbeef)
- #define BCM_6345_GPIO_BASE            (0xfffe0400)
- #define BCM_6345_SPI_BASE             (0xdeadbeef)
--#define BCM_6345_UDC0_BASE            (0xdeadbeef)
-+#define BCM_6345_UDC0_BASE            (0xfffe2100)
- #define BCM_6345_USBDMA_BASE          (0xfffe2800)
- #define BCM_6345_ENET0_BASE           (0xfffe1800)
- #define BCM_6345_ENETDMA_BASE         (0xfffe2800)
-@@ -215,7 +215,7 @@ enum bcm63xx_regs_set {
- #define BCM_6358_UART1_BASE           (0xfffe0120)
- #define BCM_6358_GPIO_BASE            (0xfffe0080)
- #define BCM_6358_SPI_BASE             (0xdeadbeef)
--#define BCM_6358_UDC0_BASE            (0xfffe0800)
-+#define BCM_6358_UDC0_BASE            (0xfffe0400)
- #define BCM_6358_OHCI0_BASE           (0xfffe1400)
- #define BCM_6358_OHCI_PRIV_BASE               (0xdeadbeef)
- #define BCM_6358_USBH_PRIV_BASE               (0xfffe1500)
-@@ -444,6 +444,7 @@ enum bcm63xx_irq {
-       IRQ_UART0,
-       IRQ_UART1,
-       IRQ_DSL,
-+      IRQ_UDC0,
-       IRQ_ENET0,
-       IRQ_ENET1,
-       IRQ_ENET_PHY,
-@@ -486,7 +487,7 @@ enum bcm63xx_irq {
- #define BCM_6345_UART0_IRQ            (IRQ_INTERNAL_BASE + 2)
- #define BCM_6345_DSL_IRQ              (IRQ_INTERNAL_BASE + 3)
- #define BCM_6345_ATM_IRQ              (IRQ_INTERNAL_BASE + 4)
--#define BCM_6345_USB_IRQ              (IRQ_INTERNAL_BASE + 5)
-+#define BCM_6345_UDC0_IRQ             (IRQ_INTERNAL_BASE + 5)
- #define BCM_6345_ENET0_IRQ            (IRQ_INTERNAL_BASE + 8)
- #define BCM_6345_ENET_PHY_IRQ         (IRQ_INTERNAL_BASE + 12)
- #define BCM_6345_ENET0_RXDMA_IRQ      (IRQ_INTERNAL_BASE + 13 + 1)
-@@ -508,10 +509,17 @@ enum bcm63xx_irq {
- #define BCM_6348_TIMER_IRQ            (IRQ_INTERNAL_BASE + 0)
- #define BCM_6348_UART0_IRQ            (IRQ_INTERNAL_BASE + 2)
- #define BCM_6348_DSL_IRQ              (IRQ_INTERNAL_BASE + 4)
-+#define BCM_6348_UDC0_IRQ             (IRQ_INTERNAL_BASE + 6)
- #define BCM_6348_ENET1_IRQ            (IRQ_INTERNAL_BASE + 7)
- #define BCM_6348_ENET0_IRQ            (IRQ_INTERNAL_BASE + 8)
- #define BCM_6348_ENET_PHY_IRQ         (IRQ_INTERNAL_BASE + 9)
- #define BCM_6348_OHCI0_IRQ            (IRQ_INTERNAL_BASE + 12)
-+#define BCM_6348_USB_CNTL_RX_DMA_IRQ  (IRQ_INTERNAL_BASE + 14)
-+#define BCM_6348_USB_CNTL_TX_DMA_IRQ  (IRQ_INTERNAL_BASE + 15)
-+#define BCM_6348_USB_BULK_RX_DMA_IRQ  (IRQ_INTERNAL_BASE + 16)
-+#define BCM_6348_USB_BULK_TX_DMA_IRQ  (IRQ_INTERNAL_BASE + 17)
-+#define BCM_6348_USB_ISO_RX_DMA_IRQ   (IRQ_INTERNAL_BASE + 18)
-+#define BCM_6348_USB_ISO_TX_DMA_IRQ   (IRQ_INTERNAL_BASE + 19)
- #define BCM_6348_ENET0_RXDMA_IRQ      (IRQ_INTERNAL_BASE + 20)
- #define BCM_6348_ENET0_TXDMA_IRQ      (IRQ_INTERNAL_BASE + 21)
- #define BCM_6348_ENET1_RXDMA_IRQ      (IRQ_INTERNAL_BASE + 22)
---- /dev/null
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_udc.h
-@@ -0,0 +1,6 @@
-+#ifndef BCM63XX_DEV_USB_UDC_H_
-+#define BCM63XX_DEV_USB_UDC_H_
-+
-+int bcm63xx_udc_register(void);
-+
-+#endif /* BCM63XX_DEV_USB_UDC_H_ */
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -47,6 +47,7 @@ struct board_info {
-       unsigned int    has_dsp:1;
-       unsigned int    has_uart0:1;
-       unsigned int    has_uart1:1;
-+      unsigned int    has_udc0:1;
-       /* ethernet config */
-       struct bcm63xx_enet_platform_data enet0;
---- a/arch/mips/bcm63xx/Makefile
-+++ b/arch/mips/bcm63xx/Makefile
-@@ -1,6 +1,6 @@
- obj-y         += clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \
-                  dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o dev-wdt.o \
--                 dev-usb-ohci.o dev-usb-ehci.o
-+                 dev-usb-ohci.o dev-usb-ehci.o dev-usb-udc.o
- obj-$(CONFIG_EARLY_PRINTK)    += early_printk.o
- obj-y         += boards/
---- a/arch/mips/bcm63xx/clk.c
-+++ b/arch/mips/bcm63xx/clk.c
-@@ -141,6 +141,30 @@ static struct clk clk_usbh = {
- };
- /*
-+ * USB slave clock
-+ */
-+static void usbs_set(struct clk *clk, int enable)
-+{
-+      u32 mask;
-+
-+      switch(bcm63xx_get_cpu_id()) {
-+      case BCM6338_CPU_ID:
-+              mask = CKCTL_6338_USBS_EN;
-+              break;
-+      case BCM6348_CPU_ID:
-+              mask = CKCTL_6348_USBS_EN;
-+              break;
-+      default:
-+              return;
-+      }
-+      bcm_hwclock_set(mask, enable);
-+}
-+
-+static struct clk clk_usbs = {
-+      .set    = usbs_set,
-+};
-+
-+/*
-  * SPI clock
-  */
- static void spi_set(struct clk *clk, int enable)
-@@ -208,6 +232,8 @@ struct clk *clk_get(struct device *dev,
-               return &clk_ephy;
-       if (!strcmp(id, "usbh"))
-               return &clk_usbh;
-+      if (!strcmp(id, "usbs"))
-+              return &clk_usbs;
-       if (!strcmp(id, "spi"))
-               return &clk_spi;
-       if (!strcmp(id, "periph"))
---- a/arch/mips/bcm63xx/Kconfig
-+++ b/arch/mips/bcm63xx/Kconfig
-@@ -7,6 +7,7 @@ config BCM63XX_CPU_6338
-       select USB_ARCH_HAS_OHCI
-       select USB_OHCI_BIG_ENDIAN_DESC
-       select USB_OHCI_BIG_ENDIAN_MMIO
-+      select USB_ARCH_HAS_UDC
- config BCM63XX_CPU_6345
-       bool "support 6345 CPU"
-@@ -19,6 +20,7 @@ config BCM63XX_CPU_6348
-       select USB_ARCH_HAS_OHCI
-       select USB_OHCI_BIG_ENDIAN_DESC
-       select USB_OHCI_BIG_ENDIAN_MMIO
-+      select USB_ARCH_HAS_UDC
- config BCM63XX_CPU_6358
-       bool "support 6358 CPU"
diff --git a/target/linux/brcm63xx/patches-2.6.37/200-extended-platform-devices.patch b/target/linux/brcm63xx/patches-2.6.37/200-extended-platform-devices.patch
deleted file mode 100644 (file)
index db2c22f..0000000
+++ /dev/null
@@ -1,25 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -915,6 +915,9 @@ int __init board_register_devices(void)
-       if (board.has_udc0)
-               bcm63xx_udc_register();
-+      if (board.num_devs)
-+              platform_add_devices(board.devs, board.num_devs);
-+
-       /* read base address of boot chip select (0) */
-       if (BCMCPU_IS_6345())
-               val = 0x1fc00000;
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -61,6 +61,10 @@ struct board_info {
-       /* Buttons */
-       struct gpio_button buttons[2];
-+
-+      /* Additional platform devices */
-+      struct platform_device **devs;
-+      unsigned int    num_devs;
- };
- #endif /* ! BOARD_BCM963XX_H_ */
diff --git a/target/linux/brcm63xx/patches-2.6.37/200-spi-board-info.patch b/target/linux/brcm63xx/patches-2.6.37/200-spi-board-info.patch
deleted file mode 100644 (file)
index 761ac96..0000000
+++ /dev/null
@@ -1,25 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -918,6 +918,9 @@ int __init board_register_devices(void)
-       if (board.num_devs)
-               platform_add_devices(board.devs, board.num_devs);
-+      if (board.num_spis)
-+              spi_register_board_info(board.spis, board.num_spis);
-+
-       /* read base address of boot chip select (0) */
-       if (BCMCPU_IS_6345())
-               val = 0x1fc00000;
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -65,6 +65,10 @@ struct board_info {
-       /* Additional platform devices */
-       struct platform_device **devs;
-       unsigned int    num_devs;
-+
-+      /* Additional platform devices */
-+      struct spi_board_info *spis;
-+      unsigned int    num_spis;
- };
- #endif /* ! BOARD_BCM963XX_H_ */
diff --git a/target/linux/brcm63xx/patches-2.6.37/210-no_ehci_over_current_check.patch b/target/linux/brcm63xx/patches-2.6.37/210-no_ehci_over_current_check.patch
deleted file mode 100644 (file)
index 513ff99..0000000
+++ /dev/null
@@ -1,16 +0,0 @@
---- a/drivers/usb/host/ehci-hub.c
-+++ b/drivers/usb/host/ehci-hub.c
-@@ -882,11 +882,13 @@ static int ehci_hub_control (
-                        * power switching; they're allowed to just limit the
-                        * current.  khubd will turn the power back on.
-                        */
-+#ifndef CONFIG_BCM63XX
-                       if (HCS_PPC (ehci->hcs_params)){
-                               ehci_writel(ehci,
-                                       temp & ~(PORT_RWC_BITS | PORT_POWER),
-                                       status_reg);
-                       }
-+#endif
-               }
-               /* whoever resumes must GetPortStatus to complete it!! */
diff --git a/target/linux/brcm63xx/patches-2.6.37/220-wl_exports.patch b/target/linux/brcm63xx/patches-2.6.37/220-wl_exports.patch
deleted file mode 100644 (file)
index 8cd87b8..0000000
+++ /dev/null
@@ -1,34 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -39,6 +39,13 @@ static unsigned int mac_addr_used;
- static struct board_info board;
- /*
-+ * Required export for WL
-+ */
-+#define NVRAM_SPACE 0x8000
-+char nvram_buf[NVRAM_SPACE];
-+EXPORT_SYMBOL(nvram_buf);
-+
-+/*
-  * known 6338 boards
-  */
- #ifdef CONFIG_BCM63XX_CPU_6338
-@@ -747,6 +754,7 @@ void __init board_prom_init(void)
-       /* extract nvram data */
-       memcpy(&nvram, boot_addr + BCM963XX_NVRAM_OFFSET, sizeof(nvram));
-+      memcpy(&nvram_buf, boot_addr + BCM963XX_NVRAM_OFFSET, NVRAM_SPACE);
-       /* check checksum before using data */
-       if (nvram.version <= 4)
---- a/arch/mips/mm/cache.c
-+++ b/arch/mips/mm/cache.c
-@@ -52,6 +52,7 @@ void (*_dma_cache_wback)(unsigned long s
- void (*_dma_cache_inv)(unsigned long start, unsigned long size);
- EXPORT_SYMBOL(_dma_cache_wback_inv);
-+EXPORT_SYMBOL(_dma_cache_inv);
- #endif /* CONFIG_DMA_NONCOHERENT */
diff --git a/target/linux/brcm63xx/patches-2.6.37/230-6358-enet1-external-mii-clk.patch b/target/linux/brcm63xx/patches-2.6.37/230-6358-enet1-external-mii-clk.patch
deleted file mode 100644 (file)
index d859410..0000000
+++ /dev/null
@@ -1,22 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -818,6 +818,8 @@ void __init board_prom_init(void)
-               if (BCMCPU_IS_6348())
-                       val |= GPIO_MODE_6348_G3_EXT_MII |
-                               GPIO_MODE_6348_G0_EXT_MII;
-+              else if (BCMCPU_IS_6358())
-+                      val |= GPIO_MODE_6358_ENET1_MII_CLK_INV;
-       }
-       bcm_gpio_writel(val, GPIO_MODE_REG);
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -402,6 +402,8 @@
- #define GPIO_MODE_6358_EXTRA_SPI_SS   (1 << 7)
- #define GPIO_MODE_6358_SERIAL_LED     (1 << 10)
- #define GPIO_MODE_6358_UTOPIA         (1 << 12)
-+#define GPIO_MODE_6358_ENET0_MII_CLK_INV (1 << 30)
-+#define GPIO_MODE_6358_ENET1_MII_CLK_INV (1 << 31)
- /*************************************************************************
diff --git a/target/linux/brcm63xx/patches-2.6.37/240-spi.patch b/target/linux/brcm63xx/patches-2.6.37/240-spi.patch
deleted file mode 100644 (file)
index 3af663e..0000000
+++ /dev/null
@@ -1,1002 +0,0 @@
---- a/arch/mips/bcm63xx/cpu.c
-+++ b/arch/mips/bcm63xx/cpu.c
-@@ -58,6 +58,7 @@ static const unsigned long bcm96338_regs
- static const int bcm96338_irqs[] = {
-       [IRQ_TIMER]             = BCM_6338_TIMER_IRQ,
-+      [IRQ_SPI]               = BCM_6338_SPI_IRQ,
-       [IRQ_UART0]             = BCM_6338_UART0_IRQ,
-       [IRQ_DSL]               = BCM_6338_DSL_IRQ,
-       [IRQ_ENET0]             = BCM_6338_ENET0_IRQ,
-@@ -132,6 +133,7 @@ static const unsigned long bcm96348_regs
- static const int bcm96348_irqs[] = {
-       [IRQ_TIMER]             = BCM_6348_TIMER_IRQ,
-+      [IRQ_SPI]               = BCM_6348_SPI_IRQ,
-       [IRQ_UART0]             = BCM_6348_UART0_IRQ,
-       [IRQ_DSL]               = BCM_6348_DSL_IRQ,
-       [IRQ_ENET0]             = BCM_6348_ENET0_IRQ,
-@@ -175,6 +177,7 @@ static const unsigned long bcm96358_regs
- static const int bcm96358_irqs[] = {
-       [IRQ_TIMER]             = BCM_6358_TIMER_IRQ,
-+      [IRQ_SPI]               = BCM_6358_SPI_IRQ,
-       [IRQ_UART0]             = BCM_6358_UART0_IRQ,
-       [IRQ_UART1]             = BCM_6358_UART1_IRQ,
-       [IRQ_DSL]               = BCM_6358_DSL_IRQ,
---- /dev/null
-+++ b/arch/mips/bcm63xx/dev-spi.c
-@@ -0,0 +1,128 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2009 Florian Fainelli <florian@openwrt.org>
-+ * Copyright (C) 2010 Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/kernel.h>
-+#include <linux/platform_device.h>
-+
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_dev_spi.h>
-+#include <bcm63xx_regs.h>
-+
-+#ifdef BCMCPU_RUNTIME_DETECT
-+/*
-+ * register offsets
-+ */
-+static const unsigned long bcm96338_regs_spi[] = {
-+      [SPI_CMD]               = SPI_BCM_6338_SPI_CMD,
-+      [SPI_INT_STATUS]        = SPI_BCM_6338_SPI_INT_STATUS,
-+      [SPI_INT_MASK_ST]       = SPI_BCM_6338_SPI_MASK_INT_ST,
-+      [SPI_INT_MASK]          = SPI_BCM_6338_SPI_INT_MASK,
-+      [SPI_ST]                = SPI_BCM_6338_SPI_ST,
-+      [SPI_CLK_CFG]           = SPI_BCM_6338_SPI_CLK_CFG,
-+      [SPI_FILL_BYTE]         = SPI_BCM_6338_SPI_FILL_BYTE,
-+      [SPI_MSG_TAIL]          = SPI_BCM_6338_SPI_MSG_TAIL,
-+      [SPI_RX_TAIL]           = SPI_BCM_6338_SPI_RX_TAIL,
-+      [SPI_MSG_CTL]           = SPI_BCM_6338_SPI_MSG_CTL,
-+      [SPI_MSG_DATA]          = SPI_BCM_6338_SPI_MSG_DATA,
-+      [SPI_RX_DATA]           = SPI_BCM_6338_SPI_RX_DATA,
-+};
-+
-+static const unsigned long bcm96348_regs_spi[] = {
-+      [SPI_CMD]               = SPI_BCM_6348_SPI_CMD,
-+      [SPI_INT_STATUS]        = SPI_BCM_6348_SPI_INT_STATUS,
-+      [SPI_INT_MASK_ST]       = SPI_BCM_6348_SPI_MASK_INT_ST,
-+      [SPI_INT_MASK]          = SPI_BCM_6348_SPI_INT_MASK,
-+      [SPI_ST]                = SPI_BCM_6348_SPI_ST,
-+      [SPI_CLK_CFG]           = SPI_BCM_6348_SPI_CLK_CFG,
-+      [SPI_FILL_BYTE]         = SPI_BCM_6348_SPI_FILL_BYTE,
-+      [SPI_MSG_TAIL]          = SPI_BCM_6348_SPI_MSG_TAIL,
-+      [SPI_RX_TAIL]           = SPI_BCM_6348_SPI_RX_TAIL,
-+      [SPI_MSG_CTL]           = SPI_BCM_6348_SPI_MSG_CTL,
-+      [SPI_MSG_DATA]          = SPI_BCM_6348_SPI_MSG_DATA,
-+      [SPI_RX_DATA]           = SPI_BCM_6348_SPI_RX_DATA,
-+};
-+
-+static const unsigned long bcm96358_regs_spi[] = {
-+      [SPI_CMD]               = SPI_BCM_6358_SPI_CMD,
-+      [SPI_INT_STATUS]        = SPI_BCM_6358_SPI_INT_STATUS,
-+      [SPI_INT_MASK_ST]       = SPI_BCM_6358_SPI_MASK_INT_ST,
-+      [SPI_INT_MASK]          = SPI_BCM_6358_SPI_INT_MASK,
-+      [SPI_ST]                = SPI_BCM_6358_SPI_STATUS,
-+      [SPI_CLK_CFG]           = SPI_BCM_6358_SPI_CLK_CFG,
-+      [SPI_FILL_BYTE]         = SPI_BCM_6358_SPI_FILL_BYTE,
-+      [SPI_MSG_TAIL]          = SPI_BCM_6358_SPI_MSG_TAIL,
-+      [SPI_RX_TAIL]           = SPI_BCM_6358_SPI_RX_TAIL,
-+      [SPI_MSG_CTL]           = SPI_BCM_6358_MSG_CTL,
-+      [SPI_MSG_DATA]          = SPI_BCM_6358_SPI_MSG_DATA,
-+      [SPI_RX_DATA]           = SPI_BCM_6358_SPI_RX_DATA,
-+};
-+
-+const unsigned long *bcm63xx_regs_spi;
-+EXPORT_SYMBOL(bcm63xx_regs_spi);
-+
-+static __init void bcm63xx_spi_regs_init(void)
-+{
-+      if (BCMCPU_IS_6338())
-+              bcm63xx_regs_spi = bcm96338_regs_spi;
-+      if (BCMCPU_IS_6348())
-+              bcm63xx_regs_spi = bcm96348_regs_spi;
-+      if (BCMCPU_IS_6358())
-+              bcm63xx_regs_spi = bcm96358_regs_spi;
-+}
-+#else
-+static __init void bcm63xx_spi_regs_init(void) { }
-+#endif
-+
-+static struct resource spi_resources[] = {
-+      {
-+              .start          = -1, /* filled at runtime */
-+              .end            = -1, /* filled at runtime */
-+              .flags          = IORESOURCE_MEM,
-+      },
-+      {
-+              .start          = -1, /* filled at runtime */
-+              .flags          = IORESOURCE_IRQ,
-+      },
-+};
-+
-+static struct bcm63xx_spi_pdata spi_pdata = {
-+      .bus_num                = 0,
-+      .num_chipselect         = 8,
-+      .speed_hz               = 50000000,     /* Fclk */
-+};
-+
-+static struct platform_device bcm63xx_spi_device = {
-+      .name           = "bcm63xx-spi",
-+      .id             = 0,
-+      .num_resources  = ARRAY_SIZE(spi_resources),
-+      .resource       = spi_resources,
-+      .dev            = {
-+              .platform_data = &spi_pdata,
-+      },
-+};
-+
-+int __init bcm63xx_spi_register(void)
-+{
-+      spi_resources[0].start = bcm63xx_regset_address(RSET_SPI);
-+      spi_resources[0].end = spi_resources[0].start;
-+      spi_resources[0].end += RSET_SPI_SIZE - 1;
-+      spi_resources[1].start = bcm63xx_get_irq_number(IRQ_SPI);
-+
-+      /* Fill in platform data */
-+      if (BCMCPU_IS_6338() || BCMCPU_IS_6348())
-+              spi_pdata.fifo_size = SPI_BCM_6338_SPI_MSG_DATA_SIZE;
-+
-+      if (BCMCPU_IS_6358())
-+              spi_pdata.fifo_size = SPI_BCM_6358_SPI_MSG_DATA_SIZE;
-+
-+      bcm63xx_spi_regs_init();
-+
-+      return platform_device_register(&bcm63xx_spi_device);
-+}
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-@@ -109,6 +109,7 @@ enum bcm63xx_regs_set {
- #define RSET_WDT_SIZE                 12
- #define RSET_ENET_SIZE                        2048
- #define RSET_ENETDMA_SIZE             2048
-+#define RSET_SPI_SIZE                 256
- #define RSET_UART_SIZE                        24
- #define RSET_UDC_SIZE                 256
- #define RSET_OHCI_SIZE                        256
-@@ -214,7 +215,7 @@ enum bcm63xx_regs_set {
- #define BCM_6358_UART0_BASE           (0xfffe0100)
- #define BCM_6358_UART1_BASE           (0xfffe0120)
- #define BCM_6358_GPIO_BASE            (0xfffe0080)
--#define BCM_6358_SPI_BASE             (0xdeadbeef)
-+#define BCM_6358_SPI_BASE             (0xfffe0800)
- #define BCM_6358_UDC0_BASE            (0xfffe0400)
- #define BCM_6358_OHCI0_BASE           (0xfffe1400)
- #define BCM_6358_OHCI_PRIV_BASE               (0xdeadbeef)
-@@ -441,6 +442,7 @@ static inline unsigned long bcm63xx_regs
-  */
- enum bcm63xx_irq {
-       IRQ_TIMER = 0,
-+      IRQ_SPI,
-       IRQ_UART0,
-       IRQ_UART1,
-       IRQ_DSL,
-@@ -507,6 +509,7 @@ enum bcm63xx_irq {
-  * 6348 irqs
-  */
- #define BCM_6348_TIMER_IRQ            (IRQ_INTERNAL_BASE + 0)
-+#define BCM_6348_SPI_IRQ              (IRQ_INTERNAL_BASE + 1)
- #define BCM_6348_UART0_IRQ            (IRQ_INTERNAL_BASE + 2)
- #define BCM_6348_DSL_IRQ              (IRQ_INTERNAL_BASE + 4)
- #define BCM_6348_UDC0_IRQ             (IRQ_INTERNAL_BASE + 6)
-@@ -531,6 +534,7 @@ enum bcm63xx_irq {
-  * 6358 irqs
-  */
- #define BCM_6358_TIMER_IRQ            (IRQ_INTERNAL_BASE + 0)
-+#define BCM_6358_SPI_IRQ              (IRQ_INTERNAL_BASE + 1)
- #define BCM_6358_UART0_IRQ            (IRQ_INTERNAL_BASE + 2)
- #define BCM_6358_UART1_IRQ            (IRQ_INTERNAL_BASE + 3)
- #define BCM_6358_OHCI0_IRQ            (IRQ_INTERNAL_BASE + 5)
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -771,4 +771,116 @@
- #define DMIPSPLLCFG_N2_SHIFT          29
- #define DMIPSPLLCFG_N2_MASK           (0x7 << DMIPSPLLCFG_N2_SHIFT)
-+/*************************************************************************
-+ * _REG relative to RSET_SPI
-+ *************************************************************************/
-+
-+/* BCM 6338 SPI core */
-+#define SPI_BCM_6338_SPI_CMD          0x00    /* 16-bits register */
-+#define SPI_BCM_6338_SPI_INT_STATUS   0x02
-+#define SPI_BCM_6338_SPI_MASK_INT_ST  0x03
-+#define SPI_BCM_6338_SPI_INT_MASK     0x04
-+#define SPI_BCM_6338_SPI_ST           0x05
-+#define SPI_BCM_6338_SPI_CLK_CFG      0x06
-+#define SPI_BCM_6338_SPI_FILL_BYTE    0x07
-+#define SPI_BCM_6338_SPI_MSG_TAIL     0x09
-+#define SPI_BCM_6338_SPI_RX_TAIL      0x0b
-+#define SPI_BCM_6338_SPI_MSG_CTL      0x40
-+#define SPI_BCM_6338_SPI_MSG_DATA     0x41
-+#define SPI_BCM_6338_SPI_MSG_DATA_SIZE        0x3f
-+#define SPI_BCM_6338_SPI_RX_DATA      0x80
-+#define SPI_BCM_6338_SPI_RX_DATA_SIZE 0x3f
-+
-+/* BCM 6348 SPI core */
-+#define SPI_BCM_6348_SPI_MASK_INT_ST  0x00
-+#define SPI_BCM_6348_SPI_INT_STATUS   0x01
-+#define SPI_BCM_6348_SPI_CMD          0x02    /* 16-bits register */
-+#define SPI_BCM_6348_SPI_FILL_BYTE    0x04
-+#define SPI_BCM_6348_SPI_CLK_CFG      0x05
-+#define SPI_BCM_6348_SPI_ST           0x06
-+#define SPI_BCM_6348_SPI_INT_MASK     0x07
-+#define SPI_BCM_6348_SPI_RX_TAIL      0x08
-+#define SPI_BCM_6348_SPI_MSG_TAIL     0x10
-+#define SPI_BCM_6348_SPI_MSG_DATA     0x40
-+#define SPI_BCM_6348_SPI_MSG_CTL      0x42
-+#define SPI_BCM_6348_SPI_MSG_DATA_SIZE        0x3f
-+#define SPI_BCM_6348_SPI_RX_DATA      0x80
-+#define SPI_BCM_6348_SPI_RX_DATA_SIZE 0x3f
-+
-+/* BCM 6358 SPI core */
-+#define SPI_BCM_6358_MSG_CTL          0x00    /* 16-bits register */
-+
-+#define SPI_BCM_6358_SPI_MSG_DATA     0x02
-+#define SPI_BCM_6358_SPI_MSG_DATA_SIZE        0x21e
-+
-+#define SPI_BCM_6358_SPI_RX_DATA      0x400
-+#define SPI_BCM_6358_SPI_RX_DATA_SIZE 0x220
-+
-+#define SPI_BCM_6358_SPI_CMD          0x700   /* 16-bits register */
-+
-+#define SPI_BCM_6358_SPI_INT_STATUS   0x702
-+#define SPI_BCM_6358_SPI_MASK_INT_ST  0x703
-+
-+#define SPI_BCM_6358_SPI_INT_MASK     0x704
-+
-+#define SPI_BCM_6358_SPI_STATUS               0x705
-+
-+#define SPI_BCM_6358_SPI_CLK_CFG      0x706
-+
-+#define SPI_BCM_6358_SPI_FILL_BYTE    0x707
-+#define SPI_BCM_6358_SPI_MSG_TAIL     0x709
-+#define SPI_BCM_6358_SPI_RX_TAIL      0x70B
-+
-+/* Shared SPI definitions */
-+
-+/* Message configuration */
-+#define SPI_FD_RW                     0x00
-+#define SPI_HD_W                      0x01
-+#define SPI_HD_R                      0x02
-+#define SPI_BYTE_CNT_SHIFT            0
-+#define SPI_MSG_TYPE_SHIFT            14
-+
-+/* Command */
-+#define SPI_CMD_NOOP                  0x01
-+#define SPI_CMD_SOFT_RESET            0x02
-+#define SPI_CMD_HARD_RESET            0x04
-+#define SPI_CMD_START_IMMEDIATE               0x08
-+#define SPI_CMD_COMMAND_SHIFT         0
-+#define SPI_CMD_COMMAND_MASK          0x000f
-+#define SPI_CMD_DEVICE_ID_SHIFT               4
-+#define SPI_CMD_PREPEND_BYTE_CNT_SHIFT        8
-+#define SPI_CMD_ONE_BYTE_SHIFT                11
-+#define SPI_CMD_ONE_WIRE_SHIFT                12
-+#define SPI_DEV_ID_0                  0
-+#define SPI_DEV_ID_1                  1
-+#define SPI_DEV_ID_2                  2
-+#define SPI_DEV_ID_3                  3
-+
-+/* Interrupt mask */
-+#define SPI_INTR_CMD_DONE             0x01
-+#define SPI_INTR_RX_OVERFLOW          0x02
-+#define SPI_INTR_TX_UNDERFLOW         0x04
-+#define SPI_INTR_TX_OVERFLOW          0x08
-+#define SPI_INTR_RX_UNDERFLOW         0x10
-+#define SPI_INTR_CLEAR_ALL            0x1f
-+
-+/* Status */
-+#define SPI_RX_EMPTY                  0x02
-+#define SPI_CMD_BUSY                  0x04
-+#define SPI_SERIAL_BUSY                       0x08
-+
-+/* Clock configuration */
-+#define SPI_CLK_20MHZ                 0x00
-+#define SPI_CLK_0_391MHZ              0x01
-+#define SPI_CLK_0_781MHZ              0x02 /* default */
-+#define SPI_CLK_1_563MHZ              0x03
-+#define SPI_CLK_3_125MHZ              0x04
-+#define SPI_CLK_6_250MHZ              0x05
-+#define SPI_CLK_12_50MHZ              0x06
-+#define SPI_CLK_25MHZ                 0x07
-+#define SPI_CLK_MASK                  0x07
-+#define SPI_SSOFFTIME_MASK            0x38
-+#define SPI_SSOFFTIME_SHIFT           3
-+#define SPI_BYTE_SWAP                 0x80
-+
- #endif /* BCM63XX_REGS_H_ */
---- /dev/null
-+++ b/drivers/spi/bcm63xx_spi.c
-@@ -0,0 +1,496 @@
-+/*
-+ * Broadcom BCM63xx SPI controller support
-+ *
-+ * Copyright (C) 2009 Florian Fainelli <florian@openwrt.org>
-+ * Copyright (C) 2010 Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * as published by the Free Software Foundation; either version 2
-+ * of the License, or (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the
-+ * Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor,
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/clk.h>
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+#include <linux/delay.h>
-+#include <linux/interrupt.h>
-+#include <linux/spi/spi.h>
-+#include <linux/completion.h>
-+#include <linux/err.h>
-+
-+#include <bcm63xx_dev_spi.h>
-+
-+#define PFX           KBUILD_MODNAME
-+#define DRV_VER               "0.1.2"
-+
-+struct bcm63xx_spi {
-+      spinlock_t              lock;
-+      int                     stopping;
-+        struct completion     done;
-+
-+      void __iomem            *regs;
-+      int                     irq;
-+
-+      /* Platform data */
-+        u32                   speed_hz;
-+      unsigned                fifo_size;
-+
-+      /* Data buffers */
-+      const unsigned char     *tx_ptr;
-+      unsigned char           *rx_ptr;
-+
-+      /* data iomem */
-+      u8 __iomem              *tx_io;
-+      const u8 __iomem        *rx_io;
-+
-+      int                     remaining_bytes;
-+
-+      struct clk              *clk;
-+      struct platform_device  *pdev;
-+};
-+
-+static inline u8 bcm_spi_readb(struct bcm63xx_spi *bs,
-+                              unsigned int offset)
-+{
-+      return bcm_readw(bs->regs + bcm63xx_spireg(offset));
-+}
-+
-+static inline u16 bcm_spi_readw(struct bcm63xx_spi *bs,
-+                              unsigned int offset)
-+{
-+      return bcm_readw(bs->regs + bcm63xx_spireg(offset));
-+}
-+
-+static inline void bcm_spi_writeb(struct bcm63xx_spi *bs,
-+                                u8 value, unsigned int offset)
-+{
-+      bcm_writeb(value, bs->regs + bcm63xx_spireg(offset));
-+}
-+
-+static inline void bcm_spi_writew(struct bcm63xx_spi *bs,
-+                                u16 value, unsigned int offset)
-+{
-+      bcm_writew(value, bs->regs + bcm63xx_spireg(offset));
-+}
-+
-+static int bcm63xx_spi_setup_transfer(struct spi_device *spi,
-+                                    struct spi_transfer *t)
-+{
-+      u8 bits_per_word;
-+      u8 clk_cfg;
-+      u32 hz;
-+      unsigned int div;
-+
-+      struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
-+
-+      bits_per_word = (t) ? t->bits_per_word : spi->bits_per_word;
-+      hz = (t) ? t->speed_hz : spi->max_speed_hz;
-+      if (bits_per_word != 8) {
-+              dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n",
-+                      __func__, bits_per_word);
-+              return -EINVAL;
-+        }
-+
-+      if (spi->chip_select > spi->master->num_chipselect) {
-+              dev_err(&spi->dev, "%s, unsupported slave %d\n",
-+                      __func__, spi->chip_select);
-+              return -EINVAL;
-+      }
-+
-+      /* Check clock setting */
-+      div = (bs->speed_hz / hz);
-+      switch (div) {
-+      case 2:
-+              clk_cfg = SPI_CLK_25MHZ;
-+              break;
-+      case 4:
-+              clk_cfg = SPI_CLK_12_50MHZ;
-+              break;
-+      case 8:
-+              clk_cfg = SPI_CLK_6_250MHZ;
-+              break;
-+      case 16:
-+              clk_cfg = SPI_CLK_3_125MHZ;
-+              break;
-+      case 32:
-+              clk_cfg = SPI_CLK_1_563MHZ;
-+              break;
-+      case 64:
-+              clk_cfg = SPI_CLK_0_781MHZ;
-+              break;
-+      case 128:
-+      default:
-+              /* Set to slowest mode for compatibility */
-+              clk_cfg = SPI_CLK_0_391MHZ;
-+              break;
-+      }
-+
-+      bcm_spi_writeb(bs, clk_cfg, SPI_CLK_CFG);
-+      dev_dbg(&spi->dev, "Setting clock register to %d (hz %d, cmd %02x)\n",
-+              div, hz, clk_cfg);
-+
-+      return 0;
-+}
-+
-+/* the spi->mode bits understood by this driver: */
-+#define MODEBITS (SPI_CPOL | SPI_CPHA)
-+
-+static int bcm63xx_spi_setup(struct spi_device *spi)
-+{
-+      struct bcm63xx_spi *bs;
-+      int ret;
-+
-+      bs = spi_master_get_devdata(spi->master);
-+
-+      if (bs->stopping)
-+              return -ESHUTDOWN;
-+
-+      if (!spi->bits_per_word)
-+              spi->bits_per_word = 8;
-+
-+      if (spi->mode & ~MODEBITS) {
-+              dev_err(&spi->dev, "%s, unsupported mode bits %x\n",
-+                      __func__, spi->mode & ~MODEBITS);
-+              return -EINVAL;
-+      }
-+
-+      ret = bcm63xx_spi_setup_transfer(spi, NULL);
-+      if (ret < 0) {
-+              dev_err(&spi->dev, "setup: unsupported mode bits %x\n",
-+                      spi->mode & ~MODEBITS);
-+              return ret;
-+      }
-+
-+      dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u nsec/bit\n",
-+              __func__, spi->mode & MODEBITS, spi->bits_per_word, 0);
-+
-+      return 0;
-+}
-+
-+/* Fill the TX FIFO with as many bytes as possible */
-+static void bcm63xx_spi_fill_tx_fifo(struct bcm63xx_spi *bs)
-+{
-+      u8 size;
-+
-+        /* Fill the Tx FIFO with as many bytes as possible */
-+      size = bs->remaining_bytes < bs->fifo_size ? bs->remaining_bytes :
-+              bs->fifo_size;
-+      memcpy_toio(bs->tx_io, bs->tx_ptr, size);
-+      bs->remaining_bytes -= size;
-+}
-+
-+static int bcm63xx_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
-+{
-+      struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
-+      u16 msg_ctl;
-+      u16 cmd;
-+
-+      dev_dbg(&spi->dev, "txrx: tx %p, rx %p, len %d\n",
-+              t->tx_buf, t->rx_buf, t->len);
-+
-+      /* Transmitter is inhibited */
-+      bs->tx_ptr = t->tx_buf;
-+      bs->rx_ptr = t->rx_buf;
-+      init_completion(&bs->done);
-+
-+      if (t->tx_buf) {
-+              bs->remaining_bytes = t->len;
-+              bcm63xx_spi_fill_tx_fifo(bs);
-+      }
-+
-+      /* Enable the command done interrupt which
-+       * we use to determine completion of a command */
-+      bcm_spi_writeb(bs, SPI_INTR_CMD_DONE, SPI_INT_MASK);
-+
-+      /* Fill in the Message control register */
-+      msg_ctl = (t->len << SPI_BYTE_CNT_SHIFT);
-+
-+      if (t->rx_buf && t->tx_buf)
-+              msg_ctl |= (SPI_FD_RW << SPI_MSG_TYPE_SHIFT);
-+      else if (t->rx_buf)
-+              msg_ctl |= (SPI_HD_R << SPI_MSG_TYPE_SHIFT);
-+      else if (t->tx_buf)
-+              msg_ctl |= (SPI_HD_W << SPI_MSG_TYPE_SHIFT);
-+
-+      bcm_spi_writew(bs, msg_ctl, SPI_MSG_CTL);
-+
-+      /* Issue the transfer */
-+      cmd = SPI_CMD_START_IMMEDIATE;
-+      cmd |= (0 << SPI_CMD_PREPEND_BYTE_CNT_SHIFT);
-+      cmd |= (spi->chip_select << SPI_CMD_DEVICE_ID_SHIFT);
-+      bcm_spi_writew(bs, cmd, SPI_CMD);
-+      wait_for_completion(&bs->done);
-+
-+      /* Disable the CMD_DONE interrupt */
-+      bcm_spi_writeb(bs, 0, SPI_INT_MASK);
-+
-+      return t->len - bs->remaining_bytes;
-+}
-+
-+static int bcm63xx_transfer(struct spi_device *spi, struct spi_message *m)
-+{
-+      struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
-+      struct spi_transfer *t;
-+      int ret = 0;
-+
-+      if (unlikely(list_empty(&m->transfers)))
-+              return -EINVAL;
-+
-+      if (bs->stopping)
-+              return -ESHUTDOWN;
-+
-+      list_for_each_entry(t, &m->transfers, transfer_list) {
-+              ret += bcm63xx_txrx_bufs(spi, t);
-+      }
-+
-+      m->complete(m->context);
-+
-+      return ret;
-+}
-+
-+/* This driver supports single master mode only. Hence
-+ * CMD_DONE is the only interrupt we care about
-+ */
-+static irqreturn_t bcm63xx_spi_interrupt(int irq, void *dev_id)
-+{
-+      struct spi_master *master = (struct spi_master *)dev_id;
-+      struct bcm63xx_spi *bs = spi_master_get_devdata(master);
-+      u8 intr;
-+      u16 cmd;
-+
-+      /* Read interupts and clear them immediately */
-+      intr = bcm_spi_readb(bs, SPI_INT_STATUS);
-+      bcm_spi_writeb(bs, SPI_INTR_CLEAR_ALL, SPI_INT_STATUS);
-+      bcm_spi_writeb(bs, 0, SPI_INT_MASK);
-+
-+      /* A tansfer completed */
-+      if (intr & SPI_INTR_CMD_DONE) {
-+              u8 rx_tail;
-+
-+              rx_tail = bcm_spi_readb(bs, SPI_RX_TAIL);
-+
-+              /* Read out all the data */
-+              if (rx_tail)
-+                      memcpy_fromio(bs->rx_ptr, bs->rx_io, rx_tail);
-+
-+              /* See if there is more data to send */
-+              if (bs->remaining_bytes > 0) {
-+                      bcm63xx_spi_fill_tx_fifo(bs);
-+
-+                      /* Start the transfer */
-+                      bcm_spi_writew(bs, SPI_HD_W << SPI_MSG_TYPE_SHIFT,
-+                                     SPI_MSG_CTL);
-+                      cmd = bcm_spi_readw(bs, SPI_CMD);
-+                      cmd |= SPI_CMD_START_IMMEDIATE;
-+                      cmd |= (0 << SPI_CMD_PREPEND_BYTE_CNT_SHIFT);
-+                      bcm_spi_writeb(bs, SPI_INTR_CMD_DONE, SPI_INT_MASK);
-+                      bcm_spi_writew(bs, cmd, SPI_CMD);
-+              } else {
-+                      complete(&bs->done);
-+              }
-+      }
-+
-+      return IRQ_HANDLED;
-+}
-+
-+
-+static int __init bcm63xx_spi_probe(struct platform_device *pdev)
-+{
-+      struct resource *r;
-+      struct device *dev = &pdev->dev;
-+      struct bcm63xx_spi_pdata *pdata = pdev->dev.platform_data;
-+      int irq;
-+      struct spi_master *master;
-+      struct clk *clk;
-+      struct bcm63xx_spi *bs;
-+      int ret;
-+
-+      r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+      if (!r) {
-+              dev_err(dev, "no iomem\n");
-+              ret = -ENXIO;
-+              goto out;
-+      }
-+
-+      irq = platform_get_irq(pdev, 0);
-+      if (irq < 0) {
-+              dev_err(dev, "no irq\n");
-+              ret = -ENXIO;
-+              goto out;
-+      }
-+
-+      clk = clk_get(dev, "spi");
-+      if (IS_ERR(clk)) {
-+              dev_err(dev, "no clock for device\n");
-+              ret = -ENODEV;
-+              goto out;
-+      }
-+
-+      master = spi_alloc_master(dev, sizeof(*bs));
-+      if (!master) {
-+              dev_err(dev, "out of memory\n");
-+              ret = -ENOMEM;
-+              goto out_free;
-+      }
-+
-+      bs = spi_master_get_devdata(master);
-+      init_completion(&bs->done);
-+
-+      platform_set_drvdata(pdev, master);
-+      bs->pdev = pdev;
-+
-+      if (!request_mem_region(r->start, r->end - r->start, PFX)) {
-+              dev_err(dev, "iomem request failed\n");
-+              ret = -ENXIO;
-+              goto out_put_master;
-+      }
-+
-+      bs->regs = ioremap_nocache(r->start, r->end - r->start);
-+      if (!bs->regs) {
-+              dev_err(dev, "unable to ioremap regs\n");
-+              ret = -ENOMEM;
-+              goto out_put_master;
-+      }
-+      bs->irq = irq;
-+      bs->clk = clk;
-+      bs->fifo_size = pdata->fifo_size;
-+
-+      ret = request_irq(irq, bcm63xx_spi_interrupt, 0, pdev->name, master);
-+      if (ret) {
-+              dev_err(dev, "unable to request irq\n");
-+              goto out_unmap;
-+      }
-+
-+      master->bus_num = pdata->bus_num;
-+      master->num_chipselect = pdata->num_chipselect;
-+      master->setup = bcm63xx_spi_setup;
-+      master->transfer = bcm63xx_transfer;
-+      bs->speed_hz = pdata->speed_hz;
-+      bs->stopping = 0;
-+      bs->tx_io = (u8*)(bs->regs + bcm63xx_spireg(SPI_MSG_DATA));
-+      bs->rx_io = (const u8*)(bs->regs + bcm63xx_spireg(SPI_RX_DATA));
-+      spin_lock_init(&bs->lock);
-+
-+      /* Initialize hardware */
-+      clk_enable(bs->clk);
-+      bcm_spi_writeb(bs, SPI_INTR_CLEAR_ALL, SPI_INT_STATUS);
-+
-+      /* register and we are done */
-+      ret = spi_register_master(master);
-+      if (ret) {
-+              dev_err(dev, "spi register failed\n");
-+              goto out_reset_hw;
-+      }
-+
-+      dev_info(dev, "at 0x%08x (irq %d, FIFOs size %d) v%s\n",
-+               r->start, irq, bs->fifo_size, DRV_VER);
-+
-+      return 0;
-+
-+out_reset_hw:
-+      clk_disable(clk);
-+      free_irq(irq, master);
-+out_unmap:
-+      iounmap(bs->regs);
-+out_put_master:
-+      spi_master_put(master);
-+out_free:
-+      clk_put(clk);
-+out:
-+      return ret;
-+}
-+
-+static int __exit bcm63xx_spi_remove(struct platform_device *pdev)
-+{
-+      struct spi_master       *master = platform_get_drvdata(pdev);
-+      struct bcm63xx_spi      *bs = spi_master_get_devdata(master);
-+      struct resource         *r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+
-+      /* reset spi block */
-+      bcm_spi_writeb(bs, 0, SPI_INT_MASK);
-+      spin_lock(&bs->lock);
-+      bs->stopping = 1;
-+
-+      /* HW shutdown */
-+      clk_disable(bs->clk);
-+      clk_put(bs->clk);
-+
-+      spin_unlock(&bs->lock);
-+
-+      free_irq(bs->irq, master);
-+      iounmap(bs->regs);
-+      release_mem_region(r->start, r->end - r->start);
-+      platform_set_drvdata(pdev, 0);
-+      spi_unregister_master(master);
-+
-+      return 0;
-+}
-+
-+#ifdef CONFIG_PM
-+static int bcm63xx_spi_suspend(struct platform_device *pdev, pm_message_t mesg)
-+{
-+      struct spi_master       *master = platform_get_drvdata(pdev);
-+      struct bcm63xx_spi      *bs = spi_master_get_devdata(master);
-+
-+        clk_disable(bs->clk);
-+
-+      return 0;
-+}
-+
-+static int bcm63xx_spi_resume(struct platform_device *pdev)
-+{
-+      struct spi_master       *master = platform_get_drvdata(pdev);
-+      struct bcm63xx_spi      *bs = spi_master_get_devdata(master);
-+
-+      clk_enable(bs->clk);
-+
-+      return 0;
-+}
-+#else
-+#define bcm63xx_spi_suspend   NULL
-+#define bcm63xx_spi_resume    NULL
-+#endif
-+
-+static struct platform_driver bcm63xx_spi_driver = {
-+      .driver = {
-+              .name   = "bcm63xx-spi",
-+              .owner  = THIS_MODULE,
-+      },
-+      .probe          = bcm63xx_spi_probe,
-+      .remove         = __exit_p(bcm63xx_spi_remove),
-+      .suspend        = bcm63xx_spi_suspend,
-+      .resume         = bcm63xx_spi_resume,
-+};
-+
-+
-+static int __init bcm63xx_spi_init(void)
-+{
-+      return platform_driver_register(&bcm63xx_spi_driver);
-+}
-+
-+static void __exit bcm63xx_spi_exit(void)
-+{
-+      platform_driver_unregister(&bcm63xx_spi_driver);
-+}
-+
-+module_init(bcm63xx_spi_init);
-+module_exit(bcm63xx_spi_exit);
-+
-+MODULE_ALIAS("platform:bcm63xx_spi");
-+MODULE_AUTHOR("Florian Fainelli <florian@openwrt.org>");
-+MODULE_AUTHOR("Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>");
-+MODULE_DESCRIPTION("Broadcom BCM63xx SPI Controller driver");
-+MODULE_LICENSE("GPL");
-+MODULE_VERSION(DRV_VER);
---- a/drivers/spi/Kconfig
-+++ b/drivers/spi/Kconfig
-@@ -60,6 +60,12 @@ config SPI_ATMEL
-         This selects a driver for the Atmel SPI Controller, present on
-         many AT32 (AVR32) and AT91 (ARM) chips.
-+config SPI_BCM63XX
-+      tristate "Broadcom BCM63xx SPI controller"
-+      depends on BCM63XX
-+      help
-+        This is the SPI controller master driver for Broadcom BCM63xx SoC.
-+
- config SPI_BFIN
-       tristate "SPI controller driver for ADI Blackfin5xx"
-       depends on BLACKFIN
---- a/drivers/spi/Makefile
-+++ b/drivers/spi/Makefile
-@@ -50,6 +50,7 @@ obj-$(CONFIG_SPI_SH_SCI)             += spi_sh_sci.
- obj-$(CONFIG_SPI_SH_MSIOF)            += spi_sh_msiof.o
- obj-$(CONFIG_SPI_STMP3XXX)            += spi_stmp.o
- obj-$(CONFIG_SPI_NUC900)              += spi_nuc900.o
-+obj-$(CONFIG_SPI_BCM63XX)             += bcm63xx_spi.o
- # special build for s3c24xx spi driver with fiq support
- spi_s3c24xx_hw-y                      := spi_s3c24xx.o
---- /dev/null
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
-@@ -0,0 +1,126 @@
-+#ifndef BCM63XX_DEV_SPI_H
-+#define BCM63XX_DEV_SPI_H
-+
-+#include <linux/types.h>
-+#include <bcm63xx_io.h>
-+#include <bcm63xx_regs.h>
-+
-+int __init bcm63xx_spi_register(void);
-+
-+struct bcm63xx_spi_pdata {
-+      unsigned int    fifo_size;
-+      int             bus_num;
-+      int             num_chipselect;
-+      u32             speed_hz;
-+};
-+
-+enum bcm63xx_regs_spi {
-+        SPI_CMD,
-+        SPI_INT_STATUS,
-+        SPI_INT_MASK_ST,
-+        SPI_INT_MASK,
-+        SPI_ST,
-+        SPI_CLK_CFG,
-+        SPI_FILL_BYTE,
-+        SPI_MSG_TAIL,
-+        SPI_RX_TAIL,
-+        SPI_MSG_CTL,
-+        SPI_MSG_DATA,
-+        SPI_RX_DATA,
-+};
-+
-+static inline unsigned long bcm63xx_spireg(enum bcm63xx_regs_spi reg)
-+{
-+#ifdef BCMCPU_RUNTIME_DETECT
-+      extern const unsigned long *bcm63xx_regs_spi;
-+        return bcm63xx_regs_spi[reg];
-+#else
-+#ifdef CONFIG_BCM63XX_CPU_6338
-+switch (reg) {
-+      case SPI_CMD:
-+              return SPI_BCM_6338_SPI_CMD;
-+      case SPI_INT_STATUS:
-+              return SPI_BCM_6338_SPI_INT_STATUS;
-+      case SPI_INT_MASK_ST:
-+              return SPI_BCM_6338_SPI_MASK_INT_ST;
-+      case SPI_INT_MASK:
-+              return SPI_BCM_6338_SPI_INT_MASK;
-+      case SPI_ST:
-+              return SPI_BCM_6338_SPI_ST;
-+      case SPI_CLK_CFG:
-+              return SPI_BCM_6338_SPI_CLK_CFG;
-+      case SPI_FILL_BYTE:
-+              return SPI_BCM_6338_SPI_FILL_BYTE;
-+      case SPI_MSG_TAIL:
-+              return SPI_BCM_6338_SPI_MSG_TAIL;
-+      case SPI_RX_TAIL:
-+              return SPI_BCM_6338_SPI_RX_TAIL;
-+      case SPI_MSG_CTL:
-+              return SPI_BCM_6338_SPI_MSG_CTL;
-+      case SPI_MSG_DATA:
-+              return SPI_BCM_6338_SPI_MSG_DATA;
-+      case SPI_RX_DATA:
-+              return SPI_BCM_6338_SPI_RX_DATA;
-+}
-+#endif
-+#ifdef CONFIG_BCM63XX_CPU_6348
-+switch (reg) {
-+      case SPI_CMD:
-+              return SPI_BCM_6348_SPI_CMD;
-+      case SPI_INT_MASK_ST:
-+              return SPI_BCM_6348_SPI_MASK_INT_ST;
-+      case SPI_INT_MASK:
-+              return SPI_BCM_6348_SPI_INT_MASK;
-+      case SPI_INT_STATUS:
-+              return SPI_BCM_6348_SPI_INT_STATUS;
-+      case SPI_ST:
-+              return SPI_BCM_6348_SPI_ST;
-+      case SPI_CLK_CFG:
-+              return SPI_BCM_6348_SPI_CLK_CFG;
-+      case SPI_FILL_BYTE:
-+              return SPI_BCM_6348_SPI_FILL_BYTE;
-+      case SPI_MSG_TAIL:
-+              return SPI_BCM_6348_SPI_MSG_TAIL;
-+      case SPI_RX_TAIL:
-+              return SPI_BCM_6348_SPI_RX_TAIL;
-+      case SPI_MSG_CTL:
-+              return SPI_BCM_6348_SPI_MSG_CTL;
-+      case SPI_MSG_DATA:
-+              return SPI_BCM_6348_SPI_MSG_DATA;
-+      case SPI_RX_DATA:
-+              return SPI_BCM_6348_SPI_RX_DATA;
-+}
-+#endif
-+#ifdef CONFIG_BCM63XX_CPU_6358
-+switch (reg) {
-+      case SPI_CMD:
-+              return SPI_BCM_6358_SPI_CMD;
-+      case SPI_INT_STATUS:
-+              return SPI_BCM_6358_SPI_INT_STATUS;
-+      case SPI_INT_MASK_ST:
-+              return SPI_BCM_6358_SPI_MASK_INT_ST;
-+      case SPI_INT_MASK:
-+              return SPI_BCM_6358_SPI_INT_MASK;
-+      case SPI_ST:
-+              return SPI_BCM_6358_SPI_STATUS;
-+      case SPI_CLK_CFG:
-+              return SPI_BCM_6358_SPI_CLK_CFG;
-+      case SPI_FILL_BYTE:
-+              return SPI_BCM_6358_SPI_FILL_BYTE;
-+      case SPI_MSG_TAIL:
-+              return SPI_BCM_6358_SPI_MSG_TAIL;
-+      case SPI_RX_TAIL:
-+              return SPI_BCM_6358_SPI_RX_TAIL;
-+      case SPI_MSG_CTL:
-+              return SPI_BCM_6358_MSG_CTL;
-+      case SPI_MSG_DATA:
-+              return SPI_BCM_6358_SPI_MSG_DATA;
-+      case SPI_RX_DATA:
-+              return SPI_BCM_6358_SPI_RX_DATA;
-+}
-+#endif
-+#endif
-+      return 0;
-+}
-+
-+#endif /* BCM63XX_DEV_SPI_H */
---- a/arch/mips/bcm63xx/Makefile
-+++ b/arch/mips/bcm63xx/Makefile
-@@ -1,6 +1,6 @@
- obj-y         += clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \
-                  dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o dev-wdt.o \
--                 dev-usb-ohci.o dev-usb-ehci.o dev-usb-udc.o
-+                 dev-usb-ohci.o dev-usb-ehci.o dev-usb-udc.o dev-spi.o
- obj-$(CONFIG_EARLY_PRINTK)    += early_printk.o
- obj-y         += boards/
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -30,6 +30,7 @@
- #include <bcm63xx_dev_usb_ohci.h>
- #include <bcm63xx_dev_usb_ehci.h>
- #include <bcm63xx_dev_usb_udc.h>
-+#include <bcm63xx_dev_spi.h>
- #include <board_bcm963xx.h>
- #define PFX   "board_bcm963xx: "
-@@ -931,6 +932,9 @@ int __init board_register_devices(void)
-       if (board.num_spis)
-               spi_register_board_info(board.spis, board.num_spis);
-+      if (!BCMCPU_IS_6345())
-+              bcm63xx_spi_register();
-+
-       /* read base address of boot chip select (0) */
-       if (BCMCPU_IS_6345())
-               val = 0x1fc00000;
diff --git a/target/linux/brcm63xx/patches-2.6.37/250-boardid_fixup.patch b/target/linux/brcm63xx/patches-2.6.37/250-boardid_fixup.patch
deleted file mode 100644 (file)
index 50e8016..0000000
+++ /dev/null
@@ -1,58 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -32,9 +32,13 @@
- #include <bcm63xx_dev_usb_udc.h>
- #include <bcm63xx_dev_spi.h>
- #include <board_bcm963xx.h>
-+#include <bcm_tag.h>
- #define PFX   "board_bcm963xx: "
-+#define CFE_OFFSET_64K                0x10000
-+#define CFE_OFFSET_128K               0x20000
-+
- static struct bcm963xx_nvram nvram;
- static unsigned int mac_addr_used;
- static struct board_info board;
-@@ -723,6 +727,29 @@ static int board_get_mac_address(u8 *mac
-       return 0;
- }
-+static void __init boardid_fixup(u8 *boot_addr)
-+{
-+      struct bcm_tag *tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_64K);
-+
-+      /* check if bcm_tag is at 64k offset */
-+      if (strncmp(nvram.name, tag->boardid, BOARDID_LEN) != 0) {
-+              /* else try 128k */
-+              tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_128K);
-+              if (strncmp(nvram.name, tag->boardid, BOARDID_LEN) != 0) {
-+                      /* No tag found */
-+                      printk(KERN_DEBUG "No bcm_tag found!\n");
-+                      return;
-+              }
-+      }
-+      /* check if we should override the boardid */
-+      if (tag->information1[0] != '+')
-+              return;
-+
-+      strncpy(nvram.name, &tag->information1[1], BOARDID_LEN);
-+
-+      printk(KERN_INFO "Overriding boardid with '%s'\n", nvram.name);
-+}
-+
- /*
-  * early init callback, read nvram data from flash and checksum it
-  */
-@@ -771,6 +798,11 @@ void __init board_prom_init(void)
-               return;
-       }
-+      if (strcmp(cfe_version, "unknown") != 0) {
-+              /* cfe present */
-+              boardid_fixup(boot_addr);
-+      }
-+
-       /* find board by name */
-       for (i = 0; i < ARRAY_SIZE(bcm963xx_boards); i++) {
-               if (strncmp(nvram.name, bcm963xx_boards[i]->name,
diff --git a/target/linux/brcm63xx/patches-2.6.37/300-alice_gate2_leds.patch b/target/linux/brcm63xx/patches-2.6.37/300-alice_gate2_leds.patch
deleted file mode 100644 (file)
index f54fab7..0000000
+++ /dev/null
@@ -1,113 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -603,6 +603,99 @@ static struct board_info __initdata boar
-       .has_ohci0 = 1,
-       .has_ehci0 = 1,
-+
-+      .leds = {
-+              /*Each led on alice gate is bi-color */
-+              {
-+                      .name           = "power:red",
-+                      .gpio           = 5,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "power:green",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+              {
-+                      .name           = "service:red",
-+                      .gpio           = 7,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:green",
-+                      .gpio           = 6,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "adsl:red",
-+                      .gpio           = 9,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "adsl:green",
-+                      .gpio           = 10,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi:red",
-+                      .gpio           = 23,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi:green",
-+                      .gpio           = 22,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "internet:red",
-+                      .gpio           = 25,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "internet:green",
-+                      .gpio           = 24,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "usr1:red",
-+                      .gpio           = 27,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "usr1:green",
-+                      .gpio           = 26,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "usr2:red",
-+                      .gpio           = 30,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "usr2:green",
-+                      .gpio           = 29,
-+                      .active_low     = 1,
-+              },
-+      },
-+
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 37,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+              {
-+                      .desc           = "wps",
-+                      .gpio           = 34,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_WPS_BUTTON,
-+                      .threshold      = 3,
-+              },
-+      },
- };
- static struct board_info __initdata board_DWVS0 = {
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -57,7 +57,7 @@ struct board_info {
-       struct bcm63xx_dsp_platform_data dsp;
-       /* GPIO LEDs */
--      struct gpio_led leds[5];
-+      struct gpio_led leds[14];
-       /* Buttons */
-       struct gpio_button buttons[2];
diff --git a/target/linux/brcm63xx/patches-2.6.37/310-96348gw_a_leds.patch b/target/linux/brcm63xx/patches-2.6.37/310-96348gw_a_leds.patch
deleted file mode 100644 (file)
index 7c5027f..0000000
+++ /dev/null
@@ -1,22 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -475,6 +475,19 @@ static struct board_info __initdata boar
-       },
-       .has_ohci0 = 1,
-+
-+      .leds = {
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = 3,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "usb",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+              }
-+      },
- };
- #endif
diff --git a/target/linux/brcm63xx/patches-2.6.37/440-board-D4PW.patch b/target/linux/brcm63xx/patches-2.6.37/440-board-D4PW.patch
deleted file mode 100644 (file)
index 07f6159..0000000
+++ /dev/null
@@ -1,66 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -489,6 +489,55 @@ static struct board_info __initdata boar
-               }
-       },
- };
-+
-+static struct board_info __initdata board_96348_D4PW = {
-+      .name                           = "D-4P-W",
-+      .expected_cpu_id                = 0x6348,
-+
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+      .has_uart0                      = 1,
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .leds = {
-+              {
-+                      .name           = "power:green",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "status",
-+                      .gpio           = 3,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "internet:green",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "internet:red",
-+                      .gpio           = 5,
-+                      .active_low     = 1,
-+              },
-+      },
-+
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 7,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
- #endif
- /*
-@@ -753,6 +802,7 @@ static const struct board_info __initdat
-       &board_DV201AMR,
-       &board_96348gw_a,
-       &board_rta1025w_16,
-+      &board_96348_D4PW,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6358
diff --git a/target/linux/brcm63xx/patches-2.6.37/441-board-NB4.patch b/target/linux/brcm63xx/patches-2.6.37/441-board-NB4.patch
deleted file mode 100644 (file)
index 2fb7ff2..0000000
+++ /dev/null
@@ -1,569 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -17,6 +17,9 @@
- #include <linux/ssb/ssb.h>
- #include <linux/gpio_buttons.h>
- #include <linux/input.h>
-+#include <linux/spi/spi.h>
-+#include <linux/spi/spi_gpio.h>
-+#include <linux/spi/74x164.h>
- #include <asm/addrspace.h>
- #include <bcm63xx_board.h>
- #include <bcm63xx_cpu.h>
-@@ -39,6 +42,12 @@
- #define CFE_OFFSET_64K                0x10000
- #define CFE_OFFSET_128K               0x20000
-+#define NB4_PID_OFFSET                0xff80
-+#define NB4_74X164_GPIO_BASE  64
-+#define NB4_SPI_GPIO_MOSI     7
-+#define NB4_SPI_GPIO_CLK      6
-+#define NB4_74HC64_GPIO(X)    (NB4_74X164_GPIO_BASE + (X))
-+
- static struct bcm963xx_nvram nvram;
- static unsigned int mac_addr_used;
- static struct board_info board;
-@@ -780,6 +789,502 @@ static struct board_info __initdata boar
-       .has_ohci0                      = 1,
- };
-+
-+struct spi_gpio_platform_data nb4_spi_gpio_data = {
-+      .sck            = NB4_SPI_GPIO_CLK,
-+      .mosi           = NB4_SPI_GPIO_MOSI,
-+      .miso           = SPI_GPIO_NO_MISO,
-+      .num_chipselect = 1,
-+};
-+
-+
-+static struct platform_device nb4_spi_gpio = {
-+      .name = "spi_gpio",
-+      .id   = 1,
-+      .dev = {
-+              .platform_data = &nb4_spi_gpio_data,
-+      },
-+};
-+
-+static struct platform_device * __initdata nb4_devices[] = {
-+      &nb4_spi_gpio,
-+};
-+
-+const struct gen_74x164_chip_platform_data nb4_74x164_platform_data = {
-+      .base = NB4_74X164_GPIO_BASE
-+};
-+
-+static struct spi_board_info nb4_spi_devices[] = {
-+      {
-+              .modalias = "74x164",
-+              .max_speed_hz = 781000,
-+              .bus_num = 1,
-+              .controller_data = (void *) SPI_GPIO_NO_CHIPSELECT,
-+              .mode = SPI_MODE_0,
-+              .platform_data = &nb4_74x164_platform_data
-+      }
-+};
-+
-+static struct board_info __initdata board_nb4_ser_r0 = {
-+      .name                           = "NB4-SER-r0",
-+      .expected_cpu_id                = 0x6358,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+
-+      .has_ohci0 = 1,
-+      .has_pccard = 1,
-+      .has_ehci0 = 1,
-+
-+      .has_udc0                       = 1,
-+
-+      .leds = {
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = NB4_74HC64_GPIO(4),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "traffic",
-+                      .gpio           = 2,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tel",
-+                      .gpio           = NB4_74HC64_GPIO(3),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tv",
-+                      .gpio           = NB4_74HC64_GPIO(2),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi",
-+                      .gpio           = 15,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "alarm",
-+                      .gpio           = NB4_74HC64_GPIO(0),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:red",
-+                      .gpio           = 29,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:green",
-+                      .gpio           = 30,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:blue",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+      },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 34,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+              {
-+                      .desc           = "wps",
-+                      .gpio           = 37,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_WPS_BUTTON,
-+                      .threshold      = 3,
-+              },
-+      },
-+      .devs = nb4_devices,
-+      .num_devs = ARRAY_SIZE(nb4_devices),
-+      .spis = nb4_spi_devices,
-+      .num_spis = ARRAY_SIZE(nb4_spi_devices),
-+};
-+
-+static struct board_info __initdata board_nb4_ser_r1 = {
-+      .name                           = "NB4-SER-r1",
-+      .expected_cpu_id                = 0x6358,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+
-+      .has_ohci0 = 1,
-+      .has_pccard = 1,
-+      .has_ehci0 = 1,
-+
-+      .has_udc0                       = 1,
-+
-+      .leds = {
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = NB4_74HC64_GPIO(4),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "traffic",
-+                      .gpio           = 2,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tel",
-+                      .gpio           = NB4_74HC64_GPIO(3),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tv",
-+                      .gpio           = NB4_74HC64_GPIO(2),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi",
-+                      .gpio           = 15,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "alarm",
-+                      .gpio           = NB4_74HC64_GPIO(0),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:red",
-+                      .gpio           = 29,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:green",
-+                      .gpio           = 30,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:blue",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+      },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 34,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+              {
-+                      .desc           = "wps",
-+                      .gpio           = 37,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_WPS_BUTTON,
-+                      .threshold      = 3,
-+              },
-+      },
-+      .devs = nb4_devices,
-+      .num_devs = ARRAY_SIZE(nb4_devices),
-+      .spis = nb4_spi_devices,
-+      .num_spis = ARRAY_SIZE(nb4_spi_devices),
-+};
-+
-+static struct board_info __initdata board_nb4_ser_r2 = {
-+      .name                           = "NB4-SER-r2",
-+      .expected_cpu_id                = 0x6358,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+
-+      .has_ohci0 = 1,
-+      .has_pccard = 1,
-+      .has_ehci0 = 1,
-+
-+      .leds = {
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = NB4_74HC64_GPIO(4),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "traffic",
-+                      .gpio           = 2,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tel",
-+                      .gpio           = NB4_74HC64_GPIO(3),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tv",
-+                      .gpio           = NB4_74HC64_GPIO(2),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi",
-+                      .gpio           = 15,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "alarm",
-+                      .gpio           = NB4_74HC64_GPIO(0),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:red",
-+                      .gpio           = 29,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:green",
-+                      .gpio           = 30,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:blue",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+      },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 34,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+              {
-+                      .desc           = "wps",
-+                      .gpio           = 37,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_WPS_BUTTON,
-+                      .threshold      = 3,
-+              },
-+      },
-+      .devs = nb4_devices,
-+      .num_devs = ARRAY_SIZE(nb4_devices),
-+      .spis = nb4_spi_devices,
-+      .num_spis = ARRAY_SIZE(nb4_spi_devices),
-+};
-+
-+static struct board_info __initdata board_nb4_fxc_r1 = {
-+      .name                           = "NB4-FXC-r1",
-+      .expected_cpu_id                = 0x6358,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+
-+      .has_ohci0 = 1,
-+      .has_pccard = 1,
-+      .has_ehci0 = 1,
-+
-+      .has_udc0                       = 1,
-+
-+      .leds = {
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = NB4_74HC64_GPIO(4),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "traffic",
-+                      .gpio           = 2,
-+              },
-+              {
-+                      .name           = "tel",
-+                      .gpio           = NB4_74HC64_GPIO(3),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tv",
-+                      .gpio           = NB4_74HC64_GPIO(2),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi",
-+                      .gpio           = 15,
-+              },
-+              {
-+                      .name           = "alarm",
-+                      .gpio           = NB4_74HC64_GPIO(0),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:red",
-+                      .gpio           = 29,
-+              },
-+              {
-+                      .name           = "service:green",
-+                      .gpio           = 30,
-+              },
-+              {
-+                      .name           = "service:blue",
-+                      .gpio           = 4,
-+              },
-+      },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 34,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+              {
-+                      .desc           = "wps",
-+                      .gpio           = 37,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_WPS_BUTTON,
-+                      .threshold      = 3,
-+              },
-+      },
-+      .devs = nb4_devices,
-+      .num_devs = ARRAY_SIZE(nb4_devices),
-+      .spis = nb4_spi_devices,
-+      .num_spis = ARRAY_SIZE(nb4_spi_devices),
-+};
-+
-+static struct board_info __initdata board_nb4_fxc_r2 = {
-+      .name                           = "NB4-FXC-r2",
-+      .expected_cpu_id                = 0x6358,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+
-+      .has_ohci0 = 1,
-+      .has_pccard = 1,
-+      .has_ehci0 = 1,
-+
-+      .leds = {
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = NB4_74HC64_GPIO(4),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "traffic",
-+                      .gpio           = 2,
-+              },
-+              {
-+                      .name           = "tel",
-+                      .gpio           = NB4_74HC64_GPIO(3),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tv",
-+                      .gpio           = NB4_74HC64_GPIO(2),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi",
-+                      .gpio           = 15,
-+              },
-+              {
-+                      .name           = "alarm",
-+                      .gpio           = NB4_74HC64_GPIO(0),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:red",
-+                      .gpio           = 29,
-+              },
-+              {
-+                      .name           = "service:green",
-+                      .gpio           = 30,
-+              },
-+              {
-+                      .name           = "service:blue",
-+                      .gpio           = 4,
-+              },
-+      },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 34,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+              {
-+                      .desc           = "wps",
-+                      .gpio           = 37,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_WPS_BUTTON,
-+                      .threshold      = 3,
-+              },
-+      },
-+      .devs = nb4_devices,
-+      .num_devs = ARRAY_SIZE(nb4_devices),
-+      .spis = nb4_spi_devices,
-+      .num_spis = ARRAY_SIZE(nb4_spi_devices),
-+};
- #endif
- /*
-@@ -810,9 +1315,30 @@ static const struct board_info __initdat
-       &board_96358vw2,
-       &board_AGPFS0,
-       &board_DWVS0,
-+      &board_nb4_ser_r0,
-+      &board_nb4_ser_r1,
-+      &board_nb4_ser_r2,
-+      &board_nb4_fxc_r1,
-+      &board_nb4_fxc_r2,
- #endif
- };
-+static void __init nb4_nvram_fixup(void)
-+{
-+      u8 *boot_addr, *p;
-+      u32 val;
-+
-+      if (BCMCPU_IS_6358() && (!strcmp(nvram.name, "96358VW"))) {
-+              val = bcm_mpi_readl(MPI_CSBASE_REG(0));
-+              val &= MPI_CSBASE_BASE_MASK;
-+              boot_addr = (u8 *)KSEG1ADDR(val);
-+              /* Extract nb4 PID */
-+              p = boot_addr + NB4_PID_OFFSET;
-+              if (!memcmp(p, "NB4-", 4))
-+                      memcpy(nvram.name, p, sizeof("NB4-XXX-rX"));
-+      }
-+}
-+
- /*
-  * Register a sane SPROMv2 to make the on-board
-  * bcm4318 WLAN work
-@@ -959,6 +1485,9 @@ void __init board_prom_init(void)
-               boardid_fixup(boot_addr);
-       }
-+      /* Fixup broken nb4 board name */
-+      nb4_nvram_fixup();
-+
-       /* find board by name */
-       for (i = 0; i < ARRAY_SIZE(bcm963xx_boards); i++) {
-               if (strncmp(nvram.name, bcm963xx_boards[i]->name,
diff --git a/target/linux/brcm63xx/patches-2.6.37/442-board-96338W2_E7T.patch b/target/linux/brcm63xx/patches-2.6.37/442-board-96338W2_E7T.patch
deleted file mode 100644 (file)
index 66ced55..0000000
+++ /dev/null
@@ -1,49 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -146,6 +146,38 @@ static struct board_info __initdata boar
-               },
-       },
- };
-+
-+static struct board_info __initdata board_96338w2_e7t = {
-+      .name                           = "96338W2_E7T",
-+      .expected_cpu_id                = 0x6338,
-+
-+      .has_enet0                      = 1,
-+
-+      .enet0 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+              .leds = {
-+              {
-+                      .name           = "ppp",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "ppp-fail",
-+                      .gpio           = 5,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "power",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+
-+              },
-+      },
-+};
- #endif
- /*
-@@ -1294,6 +1326,7 @@ static const struct board_info __initdat
- #ifdef CONFIG_BCM63XX_CPU_6338
-       &board_96338gw,
-       &board_96338w,
-+      &board_96338w2_e7t,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6345
-       &board_96345gw2,
diff --git a/target/linux/brcm63xx/patches-2.6.37/443-board-CPVA642.patch b/target/linux/brcm63xx/patches-2.6.37/443-board-CPVA642.patch
deleted file mode 100644 (file)
index 0ace02d..0000000
+++ /dev/null
@@ -1,109 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -685,6 +685,98 @@ static struct board_info __initdata boar
-       },
- };
-+static struct board_info __initdata board_CPVA642 = {
-+      .name                           = "CPVA642",
-+      .expected_cpu_id                = 0x6358,
-+
-+      .has_uart0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .has_ohci0 = 1,
-+      .has_ehci0 = 1,
-+
-+      .leds = {
-+          /* bi-color */
-+              {
-+                      .name           = "power:red",
-+                      .gpio           = 14,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "power:green",
-+                      .gpio           = 11,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+              {
-+                      .name           = "wifi:red",
-+                      .gpio           = 6,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi:green",
-+                      .gpio           = 28,
-+                      .active_low     = 0,
-+              },
-+              {
-+                      .name           = "link:red",
-+                      .gpio           = 9,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "link:green",
-+                      .gpio           = 10,
-+                      .active_low     = 1,
-+              },
-+              /* green only */
-+              {
-+                      .name           = "ether",
-+                      .gpio           = 1,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "phone1",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "phone2",
-+                      .gpio           = 2,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "usb",
-+                      .gpio           = 3,
-+                      .active_low     = 1,
-+              },
-+    },
-+
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 36,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+              {
-+                      .desc           = "wps",
-+                      .gpio           = 37,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_WPS_BUTTON,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
-+
- static struct board_info __initdata board_AGPFS0 = {
-       .name                           = "AGPF-S0",
-       .expected_cpu_id                = 0x6358,
-@@ -1347,6 +1439,7 @@ static const struct board_info __initdat
-       &board_96358vw,
-       &board_96358vw2,
-       &board_AGPFS0,
-+      &board_CPVA642,
-       &board_DWVS0,
-       &board_nb4_ser_r0,
-       &board_nb4_ser_r1,
diff --git a/target/linux/brcm63xx/patches-2.6.37/444-board_dsl_274xb_rev_c.patch b/target/linux/brcm63xx/patches-2.6.37/444-board_dsl_274xb_rev_c.patch
deleted file mode 100644 (file)
index 5bafc77..0000000
+++ /dev/null
@@ -1,70 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -914,6 +914,59 @@ static struct board_info __initdata boar
-       .has_ohci0                      = 1,
- };
-+/* D-Link DSL-274xB revison C2/C3 */
-+static struct board_info __initdata board_dsl_274xb_rev_c = {
-+      .name                           = "AW4139",
-+      .expected_cpu_id                = 0x6358,
-+
-+      .has_uart0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .leds = {
-+              {
-+                      .name           = "dsl-274xb:green:power",
-+                      .gpio           = 5,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+              {
-+                      .name           = "dsl-274xb:red:power",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "dsl-274xb:green:adsl",
-+                      .gpio           = 9,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "dsl-274xb:green:internet",
-+                      .gpio           = 2,
-+              },
-+              {
-+                      .name           = "dsl-274xb:red:internet",
-+                      .gpio           = 10,
-+              },
-+      },
-+
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 34,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
- struct spi_gpio_platform_data nb4_spi_gpio_data = {
-       .sck            = NB4_SPI_GPIO_CLK,
-       .mosi           = NB4_SPI_GPIO_MOSI,
-@@ -1441,6 +1494,7 @@ static const struct board_info __initdat
-       &board_AGPFS0,
-       &board_CPVA642,
-       &board_DWVS0,
-+      &board_dsl_274xb_rev_c,
-       &board_nb4_ser_r0,
-       &board_nb4_ser_r1,
-       &board_nb4_ser_r2,
diff --git a/target/linux/brcm63xx/patches-2.6.37/445-board_spw500v.patch b/target/linux/brcm63xx/patches-2.6.37/445-board_spw500v.patch
deleted file mode 100644 (file)
index e2215f2..0000000
+++ /dev/null
@@ -1,78 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -579,6 +579,67 @@ static struct board_info __initdata boar
-       },
- };
-+static struct board_info __initdata board_spw500v = {
-+      .name                           = "SPW500V",
-+      .expected_cpu_id                = 0x6348,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .has_dsp                        = 1,
-+      .dsp = {
-+              .gpio_rst               = 6,
-+              .gpio_int               = 34,
-+              .ext_irq                = 2,
-+              .cs                     = 2,
-+      },
-+
-+      .leds = {
-+              {
-+                      .name           = "power:red",
-+                      .gpio           = 1,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "power:green",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+              {
-+                      .name           = "ppp",
-+                      .gpio           = 3,
-+                      .active_low     = 1,
-+              },
-+              {       .name           = "pstn",
-+                      .gpio           = 28,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "voip",
-+                      .gpio           = 32,
-+                      .active_low     = 1,
-+              },
-+      },
-+
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 33,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
- #endif
- /*
-@@ -1486,6 +1547,7 @@ static const struct board_info __initdat
-       &board_96348gw_a,
-       &board_rta1025w_16,
-       &board_96348_D4PW,
-+      &board_spw500v,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6358
diff --git a/target/linux/brcm63xx/patches-2.6.37/447-board_gw6200_gw6000.patch b/target/linux/brcm63xx/patches-2.6.37/447-board_gw6200_gw6000.patch
deleted file mode 100644 (file)
index c06fda9..0000000
+++ /dev/null
@@ -1,129 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -432,6 +432,117 @@ static struct board_info __initdata boar
-       },
- };
-+static struct board_info __initdata board_gw6200 = {
-+      .name                           = "GW6200",
-+      .expected_cpu_id                = 0x6348,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .has_ohci0 = 1,
-+
-+      .has_dsp                        = 1,
-+              .dsp = {
-+        .gpio_rst             = 8, /* FIXME: What is real GPIO here? */
-+              .gpio_int               = 34,
-+              .ext_irq                = 2,
-+              .cs                     = 2,
-+      },
-+
-+      .leds = {
-+              {
-+                      .name           = "line1",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "line2",
-+                      .gpio           = 5,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "line3",
-+                      .gpio           = 6,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tel",
-+                      .gpio           = 7,
-+                      .active_low     = 1,
-+              },
-+              {
-+                  .name               = "ethernet",
-+                  .gpio               = 35,
-+                  .active_low = 1,
-+              }, 
-+      },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 36,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
-+static struct board_info __initdata board_gw6000 = {
-+      .name                           = "GW6000",
-+      .expected_cpu_id                = 0x6348,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .has_ohci0 = 1,
-+
-+      .has_dsp                        = 1,
-+      .dsp = {
-+              .gpio_rst               = 6,
-+              .gpio_int               = 34,
-+              .ext_irq                = 2,
-+              .cs                     = 2,
-+      },
-+
-+      /* GW6000 has no GPIO-controlled leds */
-+
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 36,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
-+
-+
- static struct board_info __initdata board_FAST2404 = {
-       .name                           = "F@ST2404",
-       .expected_cpu_id                = 0x6348,
-@@ -1540,6 +1651,8 @@ static const struct board_info __initdat
- #ifdef CONFIG_BCM63XX_CPU_6348
-       &board_96348r,
-       &board_96348gw,
-+      &board_gw6000,
-+      &board_gw6200,
-       &board_96348gw_10,
-       &board_96348gw_11,
-       &board_FAST2404,
diff --git a/target/linux/brcm63xx/patches-2.6.37/448-board-MAGIC.patch b/target/linux/brcm63xx/patches-2.6.37/448-board-MAGIC.patch
deleted file mode 100644 (file)
index 47e7db1..0000000
+++ /dev/null
@@ -1,87 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -751,6 +751,76 @@ static struct board_info __initdata boar
-       },
- };
-+static struct board_info __initdata board_96348sv = {
-+      .name                           = "MAGIC",
-+      .expected_cpu_id        = 0x6348,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                        = 1,
-+              .use_internal_phy       = 1,
-+      },
-+      .enet1 = {
-+              /* is has BP_ENET_EXTERNAL_PHY */
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .has_ohci0                      = 1,
-+      .has_pccard                     = 1,
-+      .has_ehci0                      = 1,
-+
-+      .has_dsp                        = 1,
-+      .dsp = {
-+              .gpio_rst               = 25,
-+              .gpio_int               = 34,
-+              .cs                             = 2,
-+              .ext_irq                = 2,
-+      },
-+
-+      .leds = {
-+              {
-+                      .name           = "voip",
-+                      .gpio           = 22,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = 5,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi",
-+                      .gpio           = 28,
-+              },
-+              {
-+                      .name           = "usb",
-+                      .gpio           = 35,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "hpna",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "power",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+              {
-+                      .name           = "stop",
-+                      .gpio           = 1,
-+                      .active_low     = 1,
-+              },
-+      },
-+};
-+
- #endif
- /*
-@@ -1661,6 +1731,7 @@ static const struct board_info __initdat
-       &board_rta1025w_16,
-       &board_96348_D4PW,
-       &board_spw500v,
-+      &board_96348sv,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6358
diff --git a/target/linux/brcm63xx/patches-2.6.37/449-board_hw553.patch b/target/linux/brcm63xx/patches-2.6.37/449-board_hw553.patch
deleted file mode 100644 (file)
index f806ad0..0000000
+++ /dev/null
@@ -1,90 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -1706,6 +1706,79 @@ static struct board_info __initdata boar
- };
- #endif
-+static struct board_info __initdata board_HW553 = {
-+      .name                           = "HW553",
-+      .expected_cpu_id                = 0x6358,
-+
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .has_ohci0 = 1,
-+      .has_ehci0 = 1,
-+
-+      .leds = {
-+              /*Each led on HW553 is bi-color (except wifi) */                
-+              {
-+                      .name           = "lan:red",
-+                      .gpio           = 34,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "lan:blue",
-+                      .gpio           = 35,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "adsl:red",
-+                      .gpio           = 22,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "adsl:blue",
-+                      .gpio           = 23,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "power:red",
-+                      .gpio           = 5,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+
-+              {
-+                      .name           = "power:blue",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi:red",
-+                      .gpio           = 25,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "internetkey:red",
-+                      .gpio           = 12,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "internetkey:blue",
-+                      .gpio           = 13,
-+                      .active_low     = 1,
-+              },
-+      },
-+};
-+
- /*
-  * all boards
-  */
-@@ -1746,6 +1819,7 @@ static const struct board_info __initdat
-       &board_nb4_ser_r2,
-       &board_nb4_fxc_r1,
-       &board_nb4_fxc_r2,
-+      &board_HW553,
- #endif
- };
diff --git a/target/linux/brcm63xx/patches-2.6.37/450-board_rta1320_16m.patch b/target/linux/brcm63xx/patches-2.6.37/450-board_rta1320_16m.patch
deleted file mode 100644 (file)
index 537a88b..0000000
+++ /dev/null
@@ -1,54 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -178,6 +178,43 @@ static struct board_info __initdata boar
-               },
-       },
- };
-+
-+static struct board_info __initdata board_rta1320_16m = {
-+      .name                           = "RTA1320_16M",
-+      .expected_cpu_id                = 0x6338,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+
-+      .enet0 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+              .leds = {
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = 3,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "ppp",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "power",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+              {
-+                      .name           = "stop",
-+                      .gpio           = 1,
-+                      .active_low     = 1,
-+              },
-+      },
-+};
- #endif
- /*
-@@ -1787,6 +1824,7 @@ static const struct board_info __initdat
-       &board_96338gw,
-       &board_96338w,
-       &board_96338w2_e7t,
-+      &board_rta1320_16m,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6345
-       &board_96345gw2,
diff --git a/target/linux/brcm63xx/patches-2.6.37/451-board_spw303v.patch b/target/linux/brcm63xx/patches-2.6.37/451-board_spw303v.patch
deleted file mode 100644 (file)
index 25b7140..0000000
+++ /dev/null
@@ -1,83 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -1741,6 +1741,72 @@ static struct board_info __initdata boar
-       .spis = nb4_spi_devices,
-       .num_spis = ARRAY_SIZE(nb4_spi_devices),
- };
-+
-+ /* T-Home Speedport W 303V Typ B */
-+static struct board_info __initdata board_spw303v = {
-+      .name                   = "96358-502V",
-+      .expected_cpu_id        = 0x6358,
-+
-+      .has_uart0              = 1,
-+      .has_enet0              = 1,
-+      .has_pci                = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .leds = {
-+              {
-+                      .name           = "spw303v:green:power+adsl",
-+                      .gpio           = 22,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "spw303v:red:power+adsl",
-+                      .gpio           = 2,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "spw303v:green:ppp",
-+                      .gpio           = 5,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "spw303v:green:ses",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "spw303v:green:voip",
-+                      .gpio           = 27,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "spw303v:green:pots",
-+                      .gpio           = 31,
-+                      .active_low     = 1,
-+              },
-+      },
-+
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 11,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+              {
-+                      .desc           = "ses",
-+                      .gpio           = 37,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_WPS_BUTTON,
-+                      .threshold      = 3,
-+              },
-+      }
-+};
- #endif
- static struct board_info __initdata board_HW553 = {
-@@ -1858,6 +1924,7 @@ static const struct board_info __initdat
-       &board_nb4_fxc_r1,
-       &board_nb4_fxc_r2,
-       &board_HW553,
-+      &board_spw303v,
- #endif
- };
diff --git a/target/linux/brcm63xx/patches-2.6.37/452-board_V2500V.patch b/target/linux/brcm63xx/patches-2.6.37/452-board_V2500V.patch
deleted file mode 100644 (file)
index 4b483d4..0000000
+++ /dev/null
@@ -1,112 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -858,6 +858,63 @@ static struct board_info __initdata boar
-       },
- };
-+      static struct board_info __initdata board_V2500V_BB = {
-+        .name                           = "V2500V_BB",
-+        .expected_cpu_id                = 0x6348,
-+
-+        .has_uart0                      = 1,
-+        .has_enet0                      = 1,
-+        .has_enet1                      = 1,
-+        .has_pci                        = 1,
-+
-+        .enet0 = {
-+                .has_phy                = 1,
-+                .use_internal_phy       = 1,
-+        },
-+        .enet1 = {
-+                .force_speed_100        = 1,
-+                .force_duplex_full      = 1,
-+        },
-+
-+      .leds = {
-+              {
-+                      .name           = "power:green",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+              {
-+                      .name           = "power:red",
-+                      .gpio           = 1,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = 2,
-+                      .active_low     = 1,
-+              },
-+              {       .name           = "ppp",
-+                      .gpio           = 3,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wireless",
-+                      .gpio           = 6,
-+                      .active_low     = 1,
-+              },
-+      },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 31,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
- #endif
- /*
-@@ -1909,6 +1966,7 @@ static const struct board_info __initdat
-       &board_96348_D4PW,
-       &board_spw500v,
-       &board_96348sv,
-+      &board_V2500V_BB,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6358
-@@ -2057,6 +2115,22 @@ void __init board_prom_init(void)
-               val &= MPI_CSBASE_BASE_MASK;
-       }
-       boot_addr = (u8 *)KSEG1ADDR(val);
-+      printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr);
-+
-+      /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
-+      /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
-+      /* Loading firmware from the CFE Prompt always loads to Bank 0 */
-+      /* Do an early check of CFE and then select bank 0 */
-+
-+              if (boot_addr == (u8 *)0xbf800000) {
-+              u8 *tmp_boot_addr;
-+              tmp_boot_addr = (u8 *)0xbfc00000; // Address of Bank 0
-+              memcpy(&nvram, tmp_boot_addr + BCM963XX_NVRAM_OFFSET, sizeof(nvram));
-+              if (!strcmp(nvram.name, "V2500V_BB")) {
-+                      printk(KERN_INFO PFX "V2500V: nvram bank 0\n");
-+                      boot_addr = (u8 *)0xbfc00000; // Bank 0
-+              }
-+      }
-       /* dump cfe version */
-       cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
-@@ -2264,6 +2338,14 @@ int __init board_register_devices(void)
-               val = bcm_mpi_readl(MPI_CSBASE_REG(0));
-               val &= MPI_CSBASE_BASE_MASK;
-       }
-+
-+      /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
-+      /* Loading from CFE always uses Bank 0 */
-+      if (!strcmp(board.name, "V2500V_BB")) {
-+              printk(KERN_INFO PFX "V2500V: Start in Bank 0\n");
-+              val = val + 0x400000; // Select Bank 0 start address
-+              }
-+
-       mtd_resources[0].start = val;
-       mtd_resources[0].end = 0x1FFFFFFF;
diff --git a/target/linux/brcm63xx/patches-2.6.37/453-board_BTV2110.patch b/target/linux/brcm63xx/patches-2.6.37/453-board_BTV2110.patch
deleted file mode 100644 (file)
index 9e280b4..0000000
+++ /dev/null
@@ -1,73 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -401,6 +401,62 @@ static struct board_info __initdata boar
-       },
- };
-+
-+/* BT Voyager 2110 */
-+static struct board_info __initdata board_V2110 = {
-+      .name                           = "V2110",
-+      .expected_cpu_id                = 0x6348,
-+
-+      .has_uart0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .leds = {
-+              {
-+                      .name           = "V2110:green:power",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+              {
-+                      .name           = "V2110:red:power",
-+                      .gpio           = 1,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "V2110:green:adsl",
-+                      .gpio           = 2,
-+                      .active_low     = 1,
-+              },
-+              {       .name           = "V2110:green:ppp",
-+                      .gpio           = 3,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "V2110:green:wireless",
-+                      .gpio           = 6,
-+                      .active_low     = 1,
-+              },
-+      },
-+
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 33,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
-+
- static struct board_info __initdata board_96348gw = {
-       .name                           = "96348GW",
-       .expected_cpu_id                = 0x6348,
-@@ -1967,6 +2023,7 @@ static const struct board_info __initdat
-       &board_spw500v,
-       &board_96348sv,
-       &board_V2500V_BB,
-+      &board_V2110,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6358
diff --git a/target/linux/brcm63xx/patches-2.6.37/454-board_livebox.patch b/target/linux/brcm63xx/patches-2.6.37/454-board_livebox.patch
deleted file mode 100644 (file)
index 6c39045..0000000
+++ /dev/null
@@ -1,251 +0,0 @@
---- a/arch/mips/bcm63xx/boards/Kconfig
-+++ b/arch/mips/bcm63xx/boards/Kconfig
-@@ -8,4 +8,10 @@ config BOARD_BCM963XX
-       select SSB
-        help
-+config BOARD_LIVEBOX
-+      bool "Inventel Livebox(es) boards"
-+      select SSB
-+      help
-+       Inventel Livebox boards using the RedBoot bootloader.
-+
- endchoice
---- a/arch/mips/bcm63xx/boards/Makefile
-+++ b/arch/mips/bcm63xx/boards/Makefile
-@@ -1,3 +1,4 @@
- obj-$(CONFIG_BOARD_BCM963XX)          += board_bcm963xx.o
-+obj-$(CONFIG_BOARD_LIVEBOX)           += board_livebox.o
- EXTRA_CFLAGS += -Werror
---- /dev/null
-+++ b/arch/mips/bcm63xx/boards/board_livebox.c
-@@ -0,0 +1,228 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2008 Florian Fainelli <florian@openwrt.org>
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/kernel.h>
-+#include <linux/string.h>
-+#include <linux/platform_device.h>
-+#include <linux/mtd/mtd.h>
-+#include <linux/mtd/partitions.h>
-+#include <linux/mtd/physmap.h>
-+#include <linux/input.h>
-+#include <linux/gpio_buttons.h>
-+#include <asm/addrspace.h>
-+#include <bcm63xx_board.h>
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_regs.h>
-+#include <bcm63xx_io.h>
-+#include <bcm63xx_dev_uart.h>
-+#include <bcm63xx_dev_pci.h>
-+#include <bcm63xx_dev_enet.h>
-+#include <bcm63xx_dev_pcmcia.h>
-+#include <bcm63xx_dev_usb_ohci.h>
-+#include <bcm63xx_dev_usb_ehci.h>
-+#include <board_bcm963xx.h>
-+
-+#define PFX   "board_livebox: "
-+
-+static unsigned int mac_addr_used = 0;
-+static struct board_info board;
-+
-+/*
-+ * known 6348 boards
-+ */
-+#ifdef CONFIG_BCM63XX_CPU_6348
-+static struct board_info __initdata board_livebox = {
-+      .name                           = "Livebox",
-+      .expected_cpu_id                = 0x6348,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .has_ohci0                      = 1,
-+      .has_pccard                     = 1,
-+      .has_ehci0                      = 1,
-+};
-+#endif
-+
-+/*
-+ * all boards
-+ */
-+static const struct board_info __initdata *bcm963xx_boards[] = {
-+#ifdef CONFIG_BCM63XX_CPU_6348
-+      &board_livebox
-+#endif
-+};
-+
-+/*
-+ * early init callback
-+ */
-+void __init board_prom_init(void)
-+{
-+      u32 val;
-+
-+      /* read base address of boot chip select (0) */
-+      val = bcm_mpi_readl(MPI_CSBASE_REG(0));
-+      val &= MPI_CSBASE_BASE_MASK;
-+
-+      /* assume board is a Livebox */
-+      memcpy(&board, bcm963xx_boards[0], sizeof(board));
-+
-+      /* setup pin multiplexing depending on board enabled device,
-+       * this has to be done this early since PCI init is done
-+       * inside arch_initcall */
-+      val = 0;
-+
-+      if (board.has_pci) {
-+              bcm63xx_pci_enabled = 1;
-+              if (BCMCPU_IS_6348())
-+                      val |= GPIO_MODE_6348_G2_PCI;
-+      }
-+
-+      if (board.has_pccard) {
-+              if (BCMCPU_IS_6348())
-+                      val |= GPIO_MODE_6348_G1_MII_PCCARD;
-+      }
-+
-+      if (board.has_enet0 && !board.enet0.use_internal_phy) {
-+              if (BCMCPU_IS_6348())
-+                      val |= GPIO_MODE_6348_G3_EXT_MII |
-+                              GPIO_MODE_6348_G0_EXT_MII;
-+      }
-+
-+      if (board.has_enet1 && !board.enet1.use_internal_phy) {
-+              if (BCMCPU_IS_6348())
-+                      val |= GPIO_MODE_6348_G3_EXT_MII |
-+                              GPIO_MODE_6348_G0_EXT_MII;
-+      }
-+
-+      bcm_gpio_writel(val, GPIO_MODE_REG);
-+}
-+
-+/*
-+ * second stage init callback, good time to panic if we couldn't
-+ * identify on which board we're running since early printk is working
-+ */
-+void __init board_setup(void)
-+{
-+      if (!board.name[0])
-+              panic("unable to detect bcm963xx board");
-+      printk(KERN_INFO PFX "board name: %s\n", board.name);
-+
-+      /* make sure we're running on expected cpu */
-+      if (bcm63xx_get_cpu_id() != board.expected_cpu_id)
-+              panic("unexpected CPU for bcm963xx board");
-+}
-+
-+/*
-+ * return board name for /proc/cpuinfo
-+ */
-+const char *board_get_name(void)
-+{
-+      return board.name;
-+}
-+
-+/*
-+ * register & return a new board mac address
-+ */
-+
-+static int board_get_mac_address(u8 *mac)
-+{
-+      u8 default_mac[ETH_ALEN] = {0x00, 0x07, 0x3A, 0x00, 0x00, 0x00};
-+      u8 *p;
-+      int count;
-+
-+      memcpy(mac, default_mac, ETH_ALEN);
-+
-+      p = mac + ETH_ALEN - 1;
-+      count = mac_addr_used;
-+
-+      while (count--) {
-+              do {
-+                      (*p)++;
-+                      if (*p != 0)
-+                              break;
-+                      p--;
-+              } while (p != mac);
-+      }
-+
-+      if (p == mac) {
-+              printk(KERN_ERR PFX "unable to fetch mac address\n");
-+              return -ENODEV;
-+      }
-+        mac_addr_used++;
-+
-+      return 0;
-+}
-+
-+static struct resource mtd_resources[] = {
-+      {
-+              .start          = 0,    /* filled at runtime */
-+              .end            = 0,    /* filled at runtime */
-+              .flags          = IORESOURCE_MEM,
-+      }
-+};
-+
-+static struct platform_device mtd_dev = {
-+      .name                   = "bcm963xx-flash",
-+      .resource               = mtd_resources,
-+      .num_resources          = ARRAY_SIZE(mtd_resources),
-+};
-+
-+
-+/*
-+ * third stage init callback, register all board devices.
-+ */
-+int __init board_register_devices(void)
-+{
-+      u32 val;
-+
-+      if (board.has_uart0)
-+              bcm63xx_uart_register(0);
-+
-+      if (board.has_pccard)
-+              bcm63xx_pcmcia_register();
-+
-+      if (board.has_enet0 &&
-+          !board_get_mac_address(board.enet0.mac_addr))
-+              bcm63xx_enet_register(0, &board.enet0);
-+
-+      if (board.has_enet1 &&
-+          !board_get_mac_address(board.enet1.mac_addr))
-+              bcm63xx_enet_register(1, &board.enet1);
-+
-+      if (board.has_ohci0)
-+              bcm63xx_ohci_register();
-+
-+      if (board.has_ehci0)
-+              bcm63xx_ehci_register();
-+
-+
-+      /* read base address of boot chip select (0) */
-+      val = bcm_mpi_readl(MPI_CSBASE_REG(0));
-+      val &= MPI_CSBASE_BASE_MASK;
-+      mtd_resources[0].start = val;
-+      mtd_resources[0].end = 0x1FFFFFFF;
-+
-+      platform_device_register(&mtd_dev);
-+
-+      return 0;
-+}
-+
diff --git a/target/linux/brcm63xx/patches-2.6.37/455-board_ct536_ct5621.patch b/target/linux/brcm63xx/patches-2.6.37/455-board_ct536_ct5621.patch
deleted file mode 100644 (file)
index 1af07ae..0000000
+++ /dev/null
@@ -1,60 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -457,6 +457,49 @@ static struct board_info __initdata boar
- };
-+static struct board_info __initdata board_ct536_ct5621 = {
-+      .name                           = "CT536_CT5621",
-+      .expected_cpu_id                = 0x6348,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 0,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .has_ohci0 = 1,
-+      .has_pccard = 1,
-+      .has_ehci0 = 1,
-+
-+      .leds = {
-+              {
-+                      .name           = "adsl-fail",
-+                      .gpio           = 2,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "power",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+      },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 33,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
- static struct board_info __initdata board_96348gw = {
-       .name                           = "96348GW",
-       .expected_cpu_id                = 0x6348,
-@@ -2024,6 +2067,7 @@ static const struct board_info __initdat
-       &board_96348sv,
-       &board_V2500V_BB,
-       &board_V2110,
-+      &board_ct536_ct5621,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6358
diff --git a/target/linux/brcm63xx/patches-2.6.37/456-board-RTA770BW.patch b/target/linux/brcm63xx/patches-2.6.37/456-board-RTA770BW.patch
deleted file mode 100644 (file)
index f1f147d..0000000
+++ /dev/null
@@ -1,24 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -227,6 +227,13 @@ static struct board_info __initdata boar
-       .has_uart0                      = 1,
- };
-+
-+static struct board_info __initdata board_ra770bw = {
-+      .name                           = "RTA770BW",
-+      .expected_cpu_id                = 0x6345,
-+
-+      .has_uart0                      = 1,
-+};
- #endif
- /*
-@@ -2050,6 +2057,7 @@ static const struct board_info __initdat
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6345
-       &board_96345gw2,
-+      &board_ra770bw,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6348
-       &board_96348r,
diff --git a/target/linux/brcm63xx/patches-2.6.37/500-ssb-add-callback-for-sprom.patch b/target/linux/brcm63xx/patches-2.6.37/500-ssb-add-callback-for-sprom.patch
deleted file mode 100644 (file)
index 349e5f5..0000000
+++ /dev/null
@@ -1,143 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -2128,6 +2128,17 @@ static struct ssb_sprom bcm63xx_sprom =
-       .boardflags_lo          = 0x2848,
-       .boardflags_hi          = 0x0000,
- };
-+
-+int bcm63xx_get_fallback_sprom(struct ssb_bus *bus, struct ssb_sprom *out)
-+{
-+      if (bus->bustype == SSB_BUSTYPE_PCI) {
-+              memcpy(out, &bcm63xx_sprom, sizeof(struct ssb_sprom));
-+              return 0;
-+      } else {
-+              printk(KERN_ERR PFX "unable to fill SPROM for given bustype.\n");
-+              return -EINVAL;
-+      }
-+}
- #endif
- /*
-@@ -2328,8 +2339,9 @@ void __init board_prom_init(void)
-       if (!board_get_mac_address(bcm63xx_sprom.il0mac)) {
-               memcpy(bcm63xx_sprom.et0mac, bcm63xx_sprom.il0mac, ETH_ALEN);
-               memcpy(bcm63xx_sprom.et1mac, bcm63xx_sprom.il0mac, ETH_ALEN);
--              if (ssb_arch_set_fallback_sprom(&bcm63xx_sprom) < 0)
--                      printk(KERN_ERR "failed to register fallback SPROM\n");
-+              if (ssb_arch_register_fallback_sprom(
-+                              &bcm63xx_get_fallback_sprom) < 0)
-+                      printk(KERN_ERR PFX "failed to register fallback SPROM\n");
-       }
- #endif
- }
---- a/drivers/ssb/pci.c
-+++ b/drivers/ssb/pci.c
-@@ -662,7 +662,6 @@ static int sprom_extract(struct ssb_bus
- static int ssb_pci_sprom_get(struct ssb_bus *bus,
-                            struct ssb_sprom *sprom)
- {
--      const struct ssb_sprom *fallback;
-       int err;
-       u16 *buf;
-@@ -707,10 +706,14 @@ static int ssb_pci_sprom_get(struct ssb_
-               if (err) {
-                       /* All CRC attempts failed.
-                        * Maybe there is no SPROM on the device?
--                       * If we have a fallback, use that. */
--                      fallback = ssb_get_fallback_sprom();
--                      if (fallback) {
--                              memcpy(sprom, fallback, sizeof(*sprom));
-+                       * Now we ask the arch code if there is some sprom
-+                       * avaliable for this device in some other storage */
-+                      err = ssb_fill_sprom_with_fallback(bus, sprom);
-+                      if (err) {
-+                              ssb_printk(KERN_WARNING PFX "WARNING: Using"
-+                                         " fallback SPROM failed (err %d)\n",
-+                                         err);
-+                      } else {
-                               err = 0;
-                               goto out_free;
-                       }
---- a/drivers/ssb/sprom.c
-+++ b/drivers/ssb/sprom.c
-@@ -17,7 +17,7 @@
- #include <linux/slab.h>
--static const struct ssb_sprom *fallback_sprom;
-+static int(*get_fallback_sprom)(struct ssb_bus *dev, struct ssb_sprom *out);
- static int sprom2hex(const u16 *sprom, char *buf, size_t buf_len,
-@@ -145,13 +145,14 @@ out:
- }
- /**
-- * ssb_arch_set_fallback_sprom - Set a fallback SPROM for use if no SPROM is found.
-+ * ssb_arch_register_fallback_sprom - Registers a method providing a fallback
-+ * SPROM if no SPROM is found.
-  *
-- * @sprom: The SPROM data structure to register.
-+ * @sprom_callback: The callbcak function.
-  *
-- * With this function the architecture implementation may register a fallback
-- * SPROM data structure. The fallback is only used for PCI based SSB devices,
-- * where no valid SPROM can be found in the shadow registers.
-+ * With this function the architecture implementation may register a callback
-+ * handler which wills the SPROM data structure. The fallback is only used for
-+ * PCI based SSB devices, where no valid SPROM can be found in the shadow registers.
-  *
-  * This function is useful for weird architectures that have a half-assed SSB device
-  * hardwired to their PCI bus.
-@@ -163,18 +164,21 @@ out:
-  *
-  * This function is available for architecture code, only. So it is not exported.
-  */
--int ssb_arch_set_fallback_sprom(const struct ssb_sprom *sprom)
-+int ssb_arch_register_fallback_sprom(int (*sprom_callback)(struct ssb_bus *bus, struct ssb_sprom *out))
- {
--      if (fallback_sprom)
-+      if (get_fallback_sprom)
-               return -EEXIST;
--      fallback_sprom = sprom;
-+      get_fallback_sprom = sprom_callback;
-       return 0;
- }
--const struct ssb_sprom *ssb_get_fallback_sprom(void)
-+int ssb_fill_sprom_with_fallback(struct ssb_bus *bus, struct ssb_sprom *out)
- {
--      return fallback_sprom;
-+      if (!get_fallback_sprom)
-+              return -ENOENT;
-+
-+      return get_fallback_sprom(bus, out);
- }
- /* http://bcm-v4.sipsolutions.net/802.11/IsSpromAvailable */
---- a/drivers/ssb/ssb_private.h
-+++ b/drivers/ssb/ssb_private.h
-@@ -171,7 +171,7 @@ ssize_t ssb_attr_sprom_store(struct ssb_
-                            const char *buf, size_t count,
-                            int (*sprom_check_crc)(const u16 *sprom, size_t size),
-                            int (*sprom_write)(struct ssb_bus *bus, const u16 *sprom));
--extern const struct ssb_sprom *ssb_get_fallback_sprom(void);
-+extern int ssb_fill_sprom_with_fallback(struct ssb_bus *bus, struct ssb_sprom *out);
- /* core.c */
---- a/include/linux/ssb/ssb.h
-+++ b/include/linux/ssb/ssb.h
-@@ -404,7 +404,9 @@ extern bool ssb_is_sprom_available(struc
- /* Set a fallback SPROM.
-  * See kdoc at the function definition for complete documentation. */
--extern int ssb_arch_set_fallback_sprom(const struct ssb_sprom *sprom);
-+extern int ssb_arch_register_fallback_sprom(
-+              int (*sprom_callback)(struct ssb_bus *bus,
-+              struct ssb_sprom *out));
- /* Suspend a SSB bus.
-  * Call this from the parent bus suspend routine. */
diff --git a/target/linux/brcm63xx/patches-2.6.37/977-ssb_export_fallback_sprom.patch b/target/linux/brcm63xx/patches-2.6.37/977-ssb_export_fallback_sprom.patch
deleted file mode 100644 (file)
index 478019d..0000000
+++ /dev/null
@@ -1,19 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -2108,7 +2108,7 @@ static void __init nb4_nvram_fixup(void)
-  * bcm4318 WLAN work
-  */
- #ifdef CONFIG_SSB_PCIHOST
--static struct ssb_sprom bcm63xx_sprom = {
-+struct ssb_sprom bcm63xx_sprom = {
-       .revision               = 0x02,
-       .board_rev              = 0x17,
-       .country_code           = 0x0,
-@@ -2128,6 +2128,7 @@ static struct ssb_sprom bcm63xx_sprom =
-       .boardflags_lo          = 0x2848,
-       .boardflags_hi          = 0x0000,
- };
-+EXPORT_SYMBOL(bcm63xx_sprom);
- int bcm63xx_get_fallback_sprom(struct ssb_bus *bus, struct ssb_sprom *out)
- {
diff --git a/target/linux/brcm63xx/patches-2.6.38/007-usb-ohci-support.patch b/target/linux/brcm63xx/patches-2.6.38/007-usb-ohci-support.patch
deleted file mode 100644 (file)
index a70b501..0000000
+++ /dev/null
@@ -1,125 +0,0 @@
-The bcm63xx SOC has an integrated OHCI controller, this patch adds
-platform device registration and change board code to register ohci
-device when necessary.
-
-Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
----
- arch/mips/bcm63xx/Kconfig                          |    6 ++
- arch/mips/bcm63xx/Makefile                         |    3 +-
- arch/mips/bcm63xx/boards/board_bcm963xx.c          |    4 ++
- arch/mips/bcm63xx/dev-usb-ohci.c                   |   49 ++++++++++++++++++++
- .../asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h        |    6 ++
- 5 files changed, 67 insertions(+), 1 deletions(-)
- create mode 100644 arch/mips/bcm63xx/dev-usb-ohci.c
- create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h
-
---- a/arch/mips/bcm63xx/Kconfig
-+++ b/arch/mips/bcm63xx/Kconfig
-@@ -16,10 +16,16 @@ config BCM63XX_CPU_6345
- config BCM63XX_CPU_6348
-       bool "support 6348 CPU"
-       select HW_HAS_PCI
-+      select USB_ARCH_HAS_OHCI
-+      select USB_OHCI_BIG_ENDIAN_DESC
-+      select USB_OHCI_BIG_ENDIAN_MMIO
- config BCM63XX_CPU_6358
-       bool "support 6358 CPU"
-       select HW_HAS_PCI
-+      select USB_ARCH_HAS_OHCI
-+      select USB_OHCI_BIG_ENDIAN_DESC
-+      select USB_OHCI_BIG_ENDIAN_MMIO
- endmenu
- source "arch/mips/bcm63xx/boards/Kconfig"
---- a/arch/mips/bcm63xx/Makefile
-+++ b/arch/mips/bcm63xx/Makefile
-@@ -1,5 +1,6 @@
- obj-y         += clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \
--                 dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o dev-wdt.o
-+                 dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o dev-wdt.o \
-+                 dev-usb-ohci.o
- obj-$(CONFIG_EARLY_PRINTK)    += early_printk.o
- obj-y         += boards/
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -25,6 +25,7 @@
- #include <bcm63xx_dev_enet.h>
- #include <bcm63xx_dev_dsp.h>
- #include <bcm63xx_dev_pcmcia.h>
-+#include <bcm63xx_dev_usb_ohci.h>
- #include <board_bcm963xx.h>
- #define PFX   "board_bcm963xx: "
-@@ -877,6 +878,9 @@ int __init board_register_devices(void)
-           !board_get_mac_address(board.enet1.mac_addr))
-               bcm63xx_enet_register(1, &board.enet1);
-+      if (board.has_ohci0)
-+              bcm63xx_ohci_register();
-+
-       if (board.has_dsp)
-               bcm63xx_dsp_register(&board.dsp);
---- /dev/null
-+++ b/arch/mips/bcm63xx/dev-usb-ohci.c
-@@ -0,0 +1,49 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2010 Maxime Bizon <mbizon@freebox.fr>
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/kernel.h>
-+#include <linux/platform_device.h>
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_dev_usb_ohci.h>
-+
-+static struct resource ohci_resources[] = {
-+      {
-+              /* start & end filled at runtime */
-+              .flags          = IORESOURCE_MEM,
-+      },
-+      {
-+              /* start filled at runtime */
-+              .flags          = IORESOURCE_IRQ,
-+      },
-+};
-+
-+static u64 ohci_dmamask = ~(u32)0;
-+
-+static struct platform_device bcm63xx_ohci_device = {
-+      .name           = "bcm63xx_ohci",
-+      .id             = 0,
-+      .num_resources  = ARRAY_SIZE(ohci_resources),
-+      .resource       = ohci_resources,
-+      .dev            = {
-+              .dma_mask               = &ohci_dmamask,
-+              .coherent_dma_mask      = 0xffffffff,
-+      },
-+};
-+
-+int __init bcm63xx_ohci_register(void)
-+{
-+      if (!BCMCPU_IS_6348() && !BCMCPU_IS_6358())
-+              return 0;
-+
-+      ohci_resources[0].start = bcm63xx_regset_address(RSET_OHCI0);
-+      ohci_resources[0].end = ohci_resources[0].start;
-+      ohci_resources[0].end += RSET_OHCI_SIZE - 1;
-+      ohci_resources[1].start = bcm63xx_get_irq_number(IRQ_OHCI0);
-+      return platform_device_register(&bcm63xx_ohci_device);
-+}
---- /dev/null
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h
-@@ -0,0 +1,6 @@
-+#ifndef BCM63XX_DEV_USB_OHCI_H_
-+#define BCM63XX_DEV_USB_OHCI_H_
-+
-+int bcm63xx_ohci_register(void);
-+
-+#endif /* BCM63XX_DEV_USB_OHCI_H_ */
diff --git a/target/linux/brcm63xx/patches-2.6.38/008-usb-ehci-support.patch b/target/linux/brcm63xx/patches-2.6.38/008-usb-ehci-support.patch
deleted file mode 100644 (file)
index 0c236f0..0000000
+++ /dev/null
@@ -1,117 +0,0 @@
-The bcm63xx SOC has an integrated EHCI controller, this patch adds
-platform device registration and change board code to register
-EHCI device when necessary.
-
-Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
----
- arch/mips/bcm63xx/Kconfig                          |    2 +
- arch/mips/bcm63xx/Makefile                         |    2 +-
- arch/mips/bcm63xx/boards/board_bcm963xx.c          |    4 ++
- arch/mips/bcm63xx/dev-usb-ehci.c                   |   49 ++++++++++++++++++++
- .../asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h        |    6 ++
- 5 files changed, 62 insertions(+), 1 deletions(-)
- create mode 100644 arch/mips/bcm63xx/dev-usb-ehci.c
- create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h
-
---- a/arch/mips/bcm63xx/Kconfig
-+++ b/arch/mips/bcm63xx/Kconfig
-@@ -26,6 +26,8 @@ config BCM63XX_CPU_6358
-       select USB_ARCH_HAS_OHCI
-       select USB_OHCI_BIG_ENDIAN_DESC
-       select USB_OHCI_BIG_ENDIAN_MMIO
-+      select USB_ARCH_HAS_EHCI
-+      select USB_EHCI_BIG_ENDIAN_MMIO
- endmenu
- source "arch/mips/bcm63xx/boards/Kconfig"
---- a/arch/mips/bcm63xx/Makefile
-+++ b/arch/mips/bcm63xx/Makefile
-@@ -1,6 +1,6 @@
- obj-y         += clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \
-                  dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o dev-wdt.o \
--                 dev-usb-ohci.o
-+                 dev-usb-ohci.o dev-usb-ehci.o
- obj-$(CONFIG_EARLY_PRINTK)    += early_printk.o
- obj-y         += boards/
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -26,6 +26,7 @@
- #include <bcm63xx_dev_dsp.h>
- #include <bcm63xx_dev_pcmcia.h>
- #include <bcm63xx_dev_usb_ohci.h>
-+#include <bcm63xx_dev_usb_ehci.h>
- #include <board_bcm963xx.h>
- #define PFX   "board_bcm963xx: "
-@@ -878,6 +879,9 @@ int __init board_register_devices(void)
-           !board_get_mac_address(board.enet1.mac_addr))
-               bcm63xx_enet_register(1, &board.enet1);
-+      if (board.has_ehci0)
-+              bcm63xx_ehci_register();
-+
-       if (board.has_ohci0)
-               bcm63xx_ohci_register();
---- /dev/null
-+++ b/arch/mips/bcm63xx/dev-usb-ehci.c
-@@ -0,0 +1,49 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2010 Maxime Bizon <mbizon@freebox.fr>
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/kernel.h>
-+#include <linux/platform_device.h>
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_dev_usb_ehci.h>
-+
-+static struct resource ehci_resources[] = {
-+      {
-+              /* start & end filled at runtime */
-+              .flags          = IORESOURCE_MEM,
-+      },
-+      {
-+              /* start filled at runtime */
-+              .flags          = IORESOURCE_IRQ,
-+      },
-+};
-+
-+static u64 ehci_dmamask = ~(u32)0;
-+
-+static struct platform_device bcm63xx_ehci_device = {
-+      .name           = "bcm63xx_ehci",
-+      .id             = 0,
-+      .num_resources  = ARRAY_SIZE(ehci_resources),
-+      .resource       = ehci_resources,
-+      .dev            = {
-+              .dma_mask               = &ehci_dmamask,
-+              .coherent_dma_mask      = 0xffffffff,
-+      },
-+};
-+
-+int __init bcm63xx_ehci_register(void)
-+{
-+      if (!BCMCPU_IS_6358())
-+              return 0;
-+
-+      ehci_resources[0].start = bcm63xx_regset_address(RSET_EHCI0);
-+      ehci_resources[0].end = ehci_resources[0].start;
-+      ehci_resources[0].end += RSET_EHCI_SIZE - 1;
-+      ehci_resources[1].start = bcm63xx_get_irq_number(IRQ_EHCI0);
-+      return platform_device_register(&bcm63xx_ehci_device);
-+}
---- /dev/null
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h
-@@ -0,0 +1,6 @@
-+#ifndef BCM63XX_DEV_USB_EHCI_H_
-+#define BCM63XX_DEV_USB_EHCI_H_
-+
-+int bcm63xx_ehci_register(void);
-+
-+#endif /* BCM63XX_DEV_USB_EHCI_H_ */
diff --git a/target/linux/brcm63xx/patches-2.6.38/010-add_bcm63xx_ohci_controller.patch b/target/linux/brcm63xx/patches-2.6.38/010-add_bcm63xx_ohci_controller.patch
deleted file mode 100644 (file)
index 7faf7c6..0000000
+++ /dev/null
@@ -1,202 +0,0 @@
-Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
----
- drivers/usb/host/ohci-bcm63xx.c |  166 +++++++++++++++++++++++++++++++++++++++
- drivers/usb/host/ohci-hcd.c     |    5 +
- drivers/usb/host/ohci.h         |    2 +-
- 3 files changed, 172 insertions(+), 1 deletions(-)
- create mode 100644 drivers/usb/host/ohci-bcm63xx.c
-
---- /dev/null
-+++ b/drivers/usb/host/ohci-bcm63xx.c
-@@ -0,0 +1,166 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2010 Maxime Bizon <mbizon@freebox.fr>
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/clk.h>
-+#include <linux/platform_device.h>
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_regs.h>
-+#include <bcm63xx_io.h>
-+
-+static struct clk *usb_host_clock;
-+
-+static int __devinit ohci_bcm63xx_start(struct usb_hcd *hcd)
-+{
-+      struct ohci_hcd *ohci = hcd_to_ohci(hcd);
-+      int ret;
-+
-+        /*
-+         * port 2 can be shared with USB slave, but all boards seem to
-+         * have only one host port populated, so we can hardcode it
-+         */
-+      ohci->num_ports = 1;
-+
-+      ret = ohci_init(ohci);
-+      if (ret < 0)
-+              return ret;
-+
-+      ret = ohci_run(ohci);
-+      if (ret < 0) {
-+              err("can't start %s", hcd->self.bus_name);
-+              ohci_stop(hcd);
-+              return ret;
-+      }
-+      return 0;
-+}
-+
-+static const struct hc_driver ohci_bcm63xx_hc_driver = {
-+      .description =          hcd_name,
-+      .product_desc =         "BCM63XX integrated OHCI controller",
-+      .hcd_priv_size =        sizeof(struct ohci_hcd),
-+
-+      .irq =                  ohci_irq,
-+      .flags =                HCD_USB11 | HCD_MEMORY,
-+      .start =                ohci_bcm63xx_start,
-+      .stop =                 ohci_stop,
-+      .shutdown =             ohci_shutdown,
-+      .urb_enqueue =          ohci_urb_enqueue,
-+      .urb_dequeue =          ohci_urb_dequeue,
-+      .endpoint_disable =     ohci_endpoint_disable,
-+      .get_frame_number =     ohci_get_frame,
-+      .hub_status_data =      ohci_hub_status_data,
-+      .hub_control =          ohci_hub_control,
-+      .start_port_reset =     ohci_start_port_reset,
-+};
-+
-+static int __devinit ohci_hcd_bcm63xx_drv_probe(struct platform_device *pdev)
-+{
-+      struct resource *res_mem;
-+      struct usb_hcd *hcd;
-+      struct ohci_hcd *ohci;
-+      u32 reg;
-+      int ret, irq;
-+
-+      res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+      irq = platform_get_irq(pdev, 0);
-+      if (!res_mem || irq < 0)
-+              return -ENODEV;
-+
-+      if (BCMCPU_IS_6348()) {
-+              struct clk *clk;
-+              /* enable USB host clock */
-+              clk = clk_get(&pdev->dev, "usbh");
-+              if (IS_ERR(clk))
-+                      return -ENODEV;
-+
-+              clk_enable(clk);
-+              usb_host_clock = clk;
-+              bcm_rset_writel(RSET_OHCI_PRIV, 0, OHCI_PRIV_REG);
-+
-+      } else if (BCMCPU_IS_6358()) {
-+              reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_REG);
-+              reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK;
-+              reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK;
-+              bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_REG);
-+              /*
-+               * The magic value comes for the original vendor BSP
-+               * and is needed for USB to work. Datasheet does not
-+               * help, so the magic value is used as-is.
-+               */
-+              bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020, USBH_PRIV_TEST_REG);
-+      } else
-+              return 0;
-+
-+      hcd = usb_create_hcd(&ohci_bcm63xx_hc_driver, &pdev->dev, "bcm63xx");
-+      if (!hcd)
-+              return -ENOMEM;
-+      hcd->rsrc_start = res_mem->start;
-+      hcd->rsrc_len = res_mem->end - res_mem->start + 1;
-+
-+      if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
-+              pr_debug("request_mem_region failed\n");
-+              ret = -EBUSY;
-+              goto out;
-+      }
-+
-+      hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
-+      if (!hcd->regs) {
-+              pr_debug("ioremap failed\n");
-+              ret = -EIO;
-+              goto out1;
-+      }
-+
-+      ohci = hcd_to_ohci(hcd);
-+      ohci->flags |= OHCI_QUIRK_BE_MMIO | OHCI_QUIRK_BE_DESC |
-+              OHCI_QUIRK_FRAME_NO;
-+      ohci_hcd_init(ohci);
-+
-+      ret = usb_add_hcd(hcd, irq, IRQF_DISABLED);
-+      if (ret)
-+              goto out2;
-+
-+      platform_set_drvdata(pdev, hcd);
-+      return 0;
-+
-+out2:
-+      iounmap(hcd->regs);
-+out1:
-+      release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
-+out:
-+      usb_put_hcd(hcd);
-+      return ret;
-+}
-+
-+static int __devexit ohci_hcd_bcm63xx_drv_remove(struct platform_device *pdev)
-+{
-+      struct usb_hcd *hcd;
-+
-+      hcd = platform_get_drvdata(pdev);
-+      usb_remove_hcd(hcd);
-+      iounmap(hcd->regs);
-+      usb_put_hcd(hcd);
-+      release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
-+      if (usb_host_clock) {
-+              clk_disable(usb_host_clock);
-+              clk_put(usb_host_clock);
-+      }
-+      platform_set_drvdata(pdev, NULL);
-+      return 0;
-+}
-+
-+static struct platform_driver ohci_hcd_bcm63xx_driver = {
-+      .probe          = ohci_hcd_bcm63xx_drv_probe,
-+      .remove         = __devexit_p(ohci_hcd_bcm63xx_drv_remove),
-+      .shutdown       = usb_hcd_platform_shutdown,
-+      .driver         = {
-+              .name   = "bcm63xx_ohci",
-+              .owner  = THIS_MODULE,
-+      },
-+};
-+
-+MODULE_ALIAS("platform:bcm63xx_ohci");
---- a/drivers/usb/host/ohci-hcd.c
-+++ b/drivers/usb/host/ohci-hcd.c
-@@ -1068,6 +1068,11 @@ MODULE_LICENSE ("GPL");
- #define PLATFORM_DRIVER               ohci_hcd_da8xx_driver
- #endif
-+#ifdef CONFIG_BCM63XX
-+#include "ohci-bcm63xx.c"
-+#define PLATFORM_DRIVER               ohci_hcd_bcm63xx_driver
-+#endif
-+
- #if defined(CONFIG_CPU_SUBTYPE_SH7720) || \
-     defined(CONFIG_CPU_SUBTYPE_SH7721) || \
-     defined(CONFIG_CPU_SUBTYPE_SH7763) || \
---- a/drivers/usb/host/ohci.h
-+++ b/drivers/usb/host/ohci.h
-@@ -656,7 +656,7 @@ static inline u32 hc32_to_cpup (const st
-  * some big-endian SOC implementations.  Same thing happens with PSW access.
-  */
--#ifdef CONFIG_PPC_MPC52xx
-+#if defined(CONFIG_PPC_MPC52xx) || defined(CONFIG_BCM63XX)
- #define big_endian_frame_no_quirk(ohci)       (ohci->flags & OHCI_QUIRK_FRAME_NO)
- #else
- #define big_endian_frame_no_quirk(ohci)       0
diff --git a/target/linux/brcm63xx/patches-2.6.38/011-add_bcm63xx_ehci_controller.patch b/target/linux/brcm63xx/patches-2.6.38/011-add_bcm63xx_ehci_controller.patch
deleted file mode 100644 (file)
index 28a1b2b..0000000
+++ /dev/null
@@ -1,178 +0,0 @@
-Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
----
- drivers/usb/host/ehci-bcm63xx.c |  154 +++++++++++++++++++++++++++++++++++++++
- drivers/usb/host/ehci-hcd.c     |    5 +
- 2 files changed, 159 insertions(+), 0 deletions(-)
- create mode 100644 drivers/usb/host/ehci-bcm63xx.c
-
---- /dev/null
-+++ b/drivers/usb/host/ehci-bcm63xx.c
-@@ -0,0 +1,154 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/platform_device.h>
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_regs.h>
-+#include <bcm63xx_io.h>
-+
-+static int ehci_bcm63xx_setup(struct usb_hcd *hcd)
-+{
-+      struct ehci_hcd *ehci = hcd_to_ehci(hcd);
-+      int retval;
-+
-+      retval = ehci_halt(ehci);
-+      if (retval)
-+              return retval;
-+
-+      retval = ehci_init(hcd);
-+      if (retval)
-+              return retval;
-+
-+      ehci_reset(ehci);
-+      ehci_port_power(ehci, 0);
-+
-+      return retval;
-+}
-+
-+
-+static const struct hc_driver ehci_bcm63xx_hc_driver = {
-+      .description =          hcd_name,
-+      .product_desc =         "BCM63XX integrated EHCI controller",
-+      .hcd_priv_size =        sizeof(struct ehci_hcd),
-+
-+      .irq =                  ehci_irq,
-+      .flags =                HCD_MEMORY | HCD_USB2,
-+
-+      .reset =                ehci_bcm63xx_setup,
-+      .start =                ehci_run,
-+      .stop =                 ehci_stop,
-+      .shutdown =             ehci_shutdown,
-+
-+      .urb_enqueue =          ehci_urb_enqueue,
-+      .urb_dequeue =          ehci_urb_dequeue,
-+      .endpoint_disable =     ehci_endpoint_disable,
-+
-+      .get_frame_number =     ehci_get_frame,
-+
-+      .hub_status_data =      ehci_hub_status_data,
-+      .hub_control =          ehci_hub_control,
-+      .bus_suspend =          ehci_bus_suspend,
-+      .bus_resume =           ehci_bus_resume,
-+      .relinquish_port =      ehci_relinquish_port,
-+      .port_handed_over =     ehci_port_handed_over,
-+};
-+
-+static int __devinit ehci_hcd_bcm63xx_drv_probe(struct platform_device *pdev)
-+{
-+      struct resource *res_mem;
-+      struct usb_hcd *hcd;
-+      struct ehci_hcd *ehci;
-+      u32 reg;
-+      int ret, irq;
-+
-+      res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+      irq = platform_get_irq(pdev, 0);;
-+      if (!res_mem || irq < 0)
-+              return -ENODEV;
-+
-+      reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_REG);
-+      reg &= ~USBH_PRIV_SWAP_EHCI_DATA_MASK;
-+      reg |= USBH_PRIV_SWAP_EHCI_ENDN_MASK;
-+      bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_REG);
-+
-+      /*
-+       * The magic value comes for the original vendor BSP and is
-+       * needed for USB to work. Datasheet does not help, so the
-+       * magic value is used as-is.
-+       */
-+      bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020, USBH_PRIV_TEST_REG);
-+
-+      hcd = usb_create_hcd(&ehci_bcm63xx_hc_driver, &pdev->dev, "bcm63xx");
-+      if (!hcd)
-+              return -ENOMEM;
-+      hcd->rsrc_start = res_mem->start;
-+      hcd->rsrc_len = res_mem->end - res_mem->start + 1;
-+
-+      if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
-+              pr_debug("request_mem_region failed\n");
-+              ret = -EBUSY;
-+              goto out;
-+      }
-+
-+      hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
-+      if (!hcd->regs) {
-+              pr_debug("ioremap failed\n");
-+              ret = -EIO;
-+              goto out1;
-+      }
-+
-+      ehci = hcd_to_ehci(hcd);
-+      ehci->big_endian_mmio = 1;
-+      ehci->big_endian_desc = 0;
-+      ehci->caps = hcd->regs;
-+      ehci->regs = hcd->regs +
-+              HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase));
-+      ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
-+      ehci->sbrn = 0x20;
-+
-+      ret = usb_add_hcd(hcd, irq, IRQF_DISABLED);
-+      if (ret)
-+              goto out2;
-+
-+      platform_set_drvdata(pdev, hcd);
-+      return 0;
-+
-+out2:
-+      iounmap(hcd->regs);
-+out1:
-+      release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
-+out:
-+      usb_put_hcd(hcd);
-+      return ret;
-+}
-+
-+static int __devexit ehci_hcd_bcm63xx_drv_remove(struct platform_device *pdev)
-+{
-+      struct usb_hcd *hcd;
-+
-+      hcd = platform_get_drvdata(pdev);
-+      usb_remove_hcd(hcd);
-+      iounmap(hcd->regs);
-+      usb_put_hcd(hcd);
-+      release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
-+      platform_set_drvdata(pdev, NULL);
-+      return 0;
-+}
-+
-+static struct platform_driver ehci_hcd_bcm63xx_driver = {
-+      .probe          = ehci_hcd_bcm63xx_drv_probe,
-+      .remove         = __devexit_p(ehci_hcd_bcm63xx_drv_remove),
-+      .shutdown       = usb_hcd_platform_shutdown,
-+      .driver         = {
-+              .name   = "bcm63xx_ehci",
-+              .owner  = THIS_MODULE,
-+      },
-+};
-+
-+MODULE_ALIAS("platform:bcm63xx_ehci");
---- a/drivers/usb/host/ehci-hcd.c
-+++ b/drivers/usb/host/ehci-hcd.c
-@@ -1254,6 +1254,11 @@ MODULE_LICENSE ("GPL");
- #define PLATFORM_DRIVER               ehci_msm_driver
- #endif
-+#ifdef CONFIG_BCM63XX
-+#include "ehci-bcm63xx.c"
-+#define PLATFORM_DRIVER               ehci_hcd_bcm63xx_driver
-+#endif
-+
- #if !defined(PCI_DRIVER) && !defined(PLATFORM_DRIVER) && \
-     !defined(PS3_SYSTEM_BUS_DRIVER) && !defined(OF_PLATFORM_DRIVER) && \
-     !defined(XILINX_OF_PLATFORM_DRIVER)
diff --git a/target/linux/brcm63xx/patches-2.6.38/040-bcm963xx_flashmap.patch b/target/linux/brcm63xx/patches-2.6.38/040-bcm963xx_flashmap.patch
deleted file mode 100644 (file)
index a216230..0000000
+++ /dev/null
@@ -1,137 +0,0 @@
-From a4d005c91d403d9f3d0272db6cc46202c06ec774 Mon Sep 17 00:00:00 2001
-From: Axel Gembe <ago@bastart.eu.org>
-Date: Mon, 12 May 2008 18:54:09 +0200
-Subject: [PATCH] bcm963xx: flashmap support
-
-Signed-off-by: Axel Gembe <ago@bastart.eu.org>
----
- arch/mips/bcm63xx/boards/board_bcm963xx.c |   19 +----------------
- drivers/mtd/maps/bcm963xx-flash.c         |   32 ++++++++++++++++++++++++----
- drivers/mtd/redboot.c                     |   13 +++++++++--
- 3 files changed, 38 insertions(+), 26 deletions(-)
-
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -816,20 +816,6 @@ void __init board_setup(void)
-               panic("unexpected CPU for bcm963xx board");
- }
--static struct mtd_partition mtd_partitions[] = {
--      {
--              .name           = "cfe",
--              .offset         = 0x0,
--              .size           = 0x40000,
--      }
--};
--
--static struct physmap_flash_data flash_data = {
--      .width                  = 2,
--      .nr_parts               = ARRAY_SIZE(mtd_partitions),
--      .parts                  = mtd_partitions,
--};
--
- static struct resource mtd_resources[] = {
-       {
-               .start          = 0,    /* filled at runtime */
-@@ -839,12 +825,9 @@ static struct resource mtd_resources[] =
- };
- static struct platform_device mtd_dev = {
--      .name                   = "physmap-flash",
-+      .name                   = "bcm963xx-flash",
-       .resource               = mtd_resources,
-       .num_resources          = ARRAY_SIZE(mtd_resources),
--      .dev                    = {
--              .platform_data  = &flash_data,
--      },
- };
- static struct gpio_led_platform_data bcm63xx_led_data;
---- a/drivers/mtd/maps/bcm963xx-flash.c
-+++ b/drivers/mtd/maps/bcm963xx-flash.c
-@@ -27,6 +27,8 @@
- #include <linux/vmalloc.h>
- #include <linux/platform_device.h>
- #include <linux/io.h>
-+#include <linux/magic.h>
-+#include <linux/jffs2.h>
- #include <asm/mach-bcm63xx/bcm963xx_tag.h>
-@@ -35,6 +37,14 @@
- #define PFX KBUILD_MODNAME ": "
-+struct squashfs_super_block {
-+      __le32 s_magic;
-+      __le32 pad0[9];
-+      __le64 bytes_used;
-+};
-+
-+extern int parse_redboot_partitions(struct mtd_info *master, struct mtd_partition **pparts, unsigned long fis_origin);
-+
- static struct mtd_partition *parsed_parts;
- static struct mtd_info *bcm963xx_mtd_info;
-@@ -219,9 +229,21 @@ probe_ok:
-                       }
-               }
-       } else {
--              dev_info(&pdev->dev, "unsupported bootloader\n");
--              err = -ENODEV;
--              goto err_probe;
-+              printk(KERN_INFO PFX "assuming RedBoot bootloader\n");
-+              if (bcm963xx_mtd_info->size > 0x00400000) {
-+                      printk(KERN_INFO PFX "Support for extended flash memory size : 0x%lx ; ONLY 64MBIT SUPPORT\n", bcm963xx_mtd_info->size);
-+                      bcm963xx_map.virt = (u32)(BCM63XX_EXTENDED_SIZE);
-+              }
-+
-+#ifdef CONFIG_MTD_REDBOOT_PARTS
-+              if (parsed_nr_parts == 0) {
-+                      int ret = parse_redboot_partitions(bcm963xx_mtd_info, &parsed_parts, 0);
-+                      if (ret > 0) {
-+                              part_type = "RedBoot";
-+                              parsed_nr_parts = ret;
-+                      }
-+              }
-+#endif
-       }
-       return add_mtd_partitions(bcm963xx_mtd_info, parsed_parts,
---- a/drivers/mtd/redboot.c
-+++ b/drivers/mtd/redboot.c
-@@ -57,7 +57,7 @@ static inline int redboot_checksum(struc
-       return 1;
- }
--static int parse_redboot_partitions(struct mtd_info *master,
-+int parse_redboot_partitions(struct mtd_info *master,
-                              struct mtd_partition **pparts,
-                              unsigned long fis_origin)
- {
-@@ -180,6 +180,14 @@ static int parse_redboot_partitions(stru
-               goto out;
-       }
-+      if (!fis_origin) {
-+              for (i = 0; i < numslots; i++) {
-+                      if (!strncmp(buf[i].name, "RedBoot", 8)) {
-+                              fis_origin = (buf[i].flash_base & (master->size << 1) - 1);
-+                      }
-+              }
-+      }
-+
-       for (i = 0; i < numslots; i++) {
-               struct fis_list *new_fl, **prev;
-@@ -202,9 +210,8 @@ static int parse_redboot_partitions(stru
-               new_fl->img = &buf[i];
-                 if (fis_origin) {
-                         buf[i].flash_base -= fis_origin;
--                } else {
--                        buf[i].flash_base &= master->size-1;
-                 }
-+              buf[i].flash_base &= (master->size << 1) - 1;
-               /* I'm sure the JFFS2 code has done me permanent damage.
-                * I now think the following is _normal_
diff --git a/target/linux/brcm63xx/patches-2.6.38/041-bcm963xx_real_rootfs_length.patch b/target/linux/brcm63xx/patches-2.6.38/041-bcm963xx_real_rootfs_length.patch
deleted file mode 100644 (file)
index dccd36f..0000000
+++ /dev/null
@@ -1,45 +0,0 @@
---- a/arch/mips/include/asm/mach-bcm63xx/bcm963xx_tag.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm963xx_tag.h
-@@ -86,8 +86,10 @@ struct bcm_tag {
-       char rootfs_crc[CRC_LEN];
-       /* 224-227: CRC32 of kernel partition */
-       char kernel_crc[CRC_LEN];
--      /* 228-235: Unused at present */
--      char reserved1[8];
-+      /* 228-231: Image sequence number */
-+      char image_sequence[4];
-+      /* 222-235: Openwrt: real rootfs length */
-+      char real_rootfs_length[4];
-       /* 236-239: CRC32 of header excluding tagVersion */
-       char header_crc[CRC_LEN];
-       /* 240-255: Unused at present */
---- a/drivers/mtd/maps/bcm963xx-flash.c
-+++ b/drivers/mtd/maps/bcm963xx-flash.c
-@@ -64,7 +64,7 @@ static int parse_cfe_partitions(struct m
-       int ret;
-       size_t retlen;
-       unsigned int rootfsaddr, kerneladdr, spareaddr;
--      unsigned int rootfslen, kernellen, sparelen, totallen;
-+      unsigned int rootfslen, kernellen, sparelen;
-       int namelen = 0;
-       int i;
-       char *boardid;
-@@ -85,7 +85,7 @@ static int parse_cfe_partitions(struct m
-       sscanf(buf->kernel_address, "%u", &kerneladdr);
-       sscanf(buf->kernel_length, "%u", &kernellen);
--      sscanf(buf->total_length, "%u", &totallen);
-+      rootfslen = *(uint32_t *)(&(buf->real_rootfs_length));
-       tagversion = &(buf->tag_version[0]);
-       boardid = &(buf->board_id[0]);
-@@ -94,7 +94,8 @@ static int parse_cfe_partitions(struct m
-       kerneladdr = kerneladdr - BCM63XX_EXTENDED_SIZE;
-       rootfsaddr = kerneladdr + kernellen;
--      spareaddr = roundup(totallen, master->erasesize) + master->erasesize;
-+      rootfslen = roundup(rootfslen, master->erasesize);
-+      spareaddr = rootfsaddr + rootfslen;
-       sparelen = master->size - spareaddr - master->erasesize;
-       rootfslen = spareaddr - rootfsaddr;
diff --git a/target/linux/brcm63xx/patches-2.6.38/070_bcm63xx_enet_vlan_incoming_fixed.patch b/target/linux/brcm63xx/patches-2.6.38/070_bcm63xx_enet_vlan_incoming_fixed.patch
deleted file mode 100644 (file)
index 8211e29..0000000
+++ /dev/null
@@ -1,11 +0,0 @@
---- a/drivers/net/bcm63xx_enet.c
-+++ b/drivers/net/bcm63xx_enet.c
-@@ -1515,7 +1515,7 @@ static int compute_hw_mtu(struct bcm_ene
-       actual_mtu = mtu;
-       /* add ethernet header + vlan tag size */
--      actual_mtu += VLAN_ETH_HLEN;
-+      actual_mtu += VLAN_ETH_HLEN + VLAN_HLEN;
-       if (actual_mtu < 64 || actual_mtu > BCMENET_MAX_MTU)
-               return -EINVAL;
diff --git a/target/linux/brcm63xx/patches-2.6.38/100-reset_buttons.patch b/target/linux/brcm63xx/patches-2.6.38/100-reset_buttons.patch
deleted file mode 100644 (file)
index 786c18b..0000000
+++ /dev/null
@@ -1,98 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -15,6 +15,8 @@
- #include <linux/mtd/partitions.h>
- #include <linux/mtd/physmap.h>
- #include <linux/ssb/ssb.h>
-+#include <linux/gpio_buttons.h>
-+#include <linux/input.h>
- #include <asm/addrspace.h>
- #include <bcm63xx_board.h>
- #include <bcm63xx_cpu.h>
-@@ -296,6 +298,16 @@ static struct board_info __initdata boar
-                       .active_low     = 1,
-               },
-       },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 33,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
- };
- static struct board_info __initdata board_96348gw = {
-@@ -354,6 +366,16 @@ static struct board_info __initdata boar
-                       .active_low     = 1,
-               },
-       },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 36,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
- };
- static struct board_info __initdata board_FAST2404 = {
-@@ -838,12 +860,23 @@ static struct platform_device bcm63xx_gp
-       .dev.platform_data      = &bcm63xx_led_data,
- };
-+static struct gpio_buttons_platform_data bcm63xx_gpio_buttons_data = {
-+      .poll_interval  = 20,
-+};
-+
-+static struct platform_device bcm63xx_gpio_buttons_device = {
-+      .name           = "gpio-buttons",
-+      .id             = 0,
-+      .dev.platform_data = &bcm63xx_gpio_buttons_data,
-+};
-+
- /*
-  * third stage init callback, register all board devices.
-  */
- int __init board_register_devices(void)
- {
-       u32 val;
-+      int button_count = 0;
-       if (board.has_uart0)
-               bcm63xx_uart_register(0);
-@@ -888,5 +921,16 @@ int __init board_register_devices(void)
-       platform_device_register(&bcm63xx_gpio_leds);
-+      /* count number of BUTTONs defined by this device */
-+      while (button_count < ARRAY_SIZE(board.buttons) && board.buttons[button_count].desc)
-+              button_count++;
-+
-+      if (button_count) {
-+              bcm63xx_gpio_buttons_data.nbuttons = button_count;
-+              bcm63xx_gpio_buttons_data.buttons = board.buttons;
-+
-+              platform_device_register(&bcm63xx_gpio_buttons_device);
-+      }
-+
-       return 0;
- }
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -57,6 +57,9 @@ struct board_info {
-       /* GPIO LEDs */
-       struct gpio_led leds[5];
-+
-+      /* Buttons */
-+      struct gpio_button buttons[2];
- };
- #endif /* ! BOARD_BCM963XX_H_ */
diff --git a/target/linux/brcm63xx/patches-2.6.38/110-gpiodev.patch b/target/linux/brcm63xx/patches-2.6.38/110-gpiodev.patch
deleted file mode 100644 (file)
index fc99f53..0000000
+++ /dev/null
@@ -1,22 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -852,6 +852,10 @@ static struct platform_device mtd_dev =
-       .num_resources          = ARRAY_SIZE(mtd_resources),
- };
-+static struct resource gpiodev_resource = {
-+      .start                  = 0xFFFFFFFF,
-+};
-+
- static struct gpio_led_platform_data bcm63xx_led_data;
- static struct platform_device bcm63xx_gpio_leds = {
-@@ -916,6 +920,8 @@ int __init board_register_devices(void)
-       platform_device_register(&mtd_dev);
-+      platform_device_register_simple("GPIODEV", 0, &gpiodev_resource, 1);
-+
-       bcm63xx_led_data.num_leds = ARRAY_SIZE(board.leds);
-       bcm63xx_led_data.leds = board.leds;
diff --git a/target/linux/brcm63xx/patches-2.6.38/141-led_count.patch b/target/linux/brcm63xx/patches-2.6.38/141-led_count.patch
deleted file mode 100644 (file)
index baf0920..0000000
+++ /dev/null
@@ -1,23 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -881,6 +881,7 @@ int __init board_register_devices(void)
- {
-       u32 val;
-       int button_count = 0;
-+      int led_count = 0;
-       if (board.has_uart0)
-               bcm63xx_uart_register(0);
-@@ -922,7 +923,11 @@ int __init board_register_devices(void)
-       platform_device_register_simple("GPIODEV", 0, &gpiodev_resource, 1);
--      bcm63xx_led_data.num_leds = ARRAY_SIZE(board.leds);
-+      /* count number of LEDs defined by this device */
-+      while (led_count < ARRAY_SIZE(board.leds) && board.leds[led_count].name)
-+        led_count++;
-+
-+      bcm63xx_led_data.num_leds = led_count;
-       bcm63xx_led_data.leds = board.leds;
-       platform_device_register(&bcm63xx_gpio_leds);
diff --git a/target/linux/brcm63xx/patches-2.6.38/180-udc_preliminary_support.patch b/target/linux/brcm63xx/patches-2.6.38/180-udc_preliminary_support.patch
deleted file mode 100644 (file)
index 7b341b7..0000000
+++ /dev/null
@@ -1,243 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -29,6 +29,7 @@
- #include <bcm63xx_dev_pcmcia.h>
- #include <bcm63xx_dev_usb_ohci.h>
- #include <bcm63xx_dev_usb_ehci.h>
-+#include <bcm63xx_dev_usb_udc.h>
- #include <board_bcm963xx.h>
- #define PFX   "board_bcm963xx: "
-@@ -400,6 +401,8 @@ static struct board_info __initdata boar
-       .has_ohci0                      = 1,
-       .has_pccard                     = 1,
-       .has_ehci0                      = 1,
-+
-+      .has_udc0                       = 1,
- };
- static struct board_info __initdata board_rta1025w_16 = {
-@@ -909,6 +912,9 @@ int __init board_register_devices(void)
-       if (board.has_dsp)
-               bcm63xx_dsp_register(&board.dsp);
-+      if (board.has_udc0)
-+              bcm63xx_udc_register();
-+
-       /* read base address of boot chip select (0) */
-       if (BCMCPU_IS_6345())
-               val = 0x1fc00000;
---- /dev/null
-+++ b/arch/mips/bcm63xx/dev-usb-udc.c
-@@ -0,0 +1,58 @@
-+/*
-+ * Copyright (C) 2009 Henk Vergonet <Henk.Vergonet@gmail.com>
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License as
-+ * published by the Free Software Foundation; either version 2 of
-+ * the License, or (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
-+ */
-+#include <linux/init.h>
-+#include <linux/kernel.h>
-+#include <linux/platform_device.h>
-+#include <bcm63xx_cpu.h>
-+
-+static struct resource udc_resources[] = {
-+      {
-+              .start          = -1, /* filled at runtime */
-+              .end            = -1, /* filled at runtime */
-+              .flags          = IORESOURCE_MEM,
-+      },
-+      {
-+              .start          = -1, /* filled at runtime */
-+              .flags          = IORESOURCE_IRQ,
-+      },
-+};
-+
-+static u64 udc_dmamask = ~(u32)0;
-+
-+static struct platform_device bcm63xx_udc_device = {
-+      .name           = "bcm63xx-udc",
-+      .id             = 0,
-+      .num_resources  = ARRAY_SIZE(udc_resources),
-+      .resource       = udc_resources,
-+      .dev            = {
-+              .dma_mask               = &udc_dmamask,
-+              .coherent_dma_mask      = 0xffffffff,
-+      },
-+};
-+
-+int __init bcm63xx_udc_register(void)
-+{
-+      if (!BCMCPU_IS_6338() && !BCMCPU_IS_6345() && !BCMCPU_IS_6348())
-+              return 0;
-+
-+      udc_resources[0].start = bcm63xx_regset_address(RSET_UDC0);
-+      udc_resources[0].end = udc_resources[0].start;
-+      udc_resources[0].end += RSET_UDC_SIZE - 1;
-+      udc_resources[1].start = bcm63xx_get_irq_number(IRQ_UDC0);
-+      return platform_device_register(&bcm63xx_udc_device);
-+}
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-@@ -127,7 +127,7 @@ enum bcm63xx_regs_set {
- #define BCM_6338_UART1_BASE           (0xdeadbeef)
- #define BCM_6338_GPIO_BASE            (0xfffe0400)
- #define BCM_6338_SPI_BASE             (0xfffe0c00)
--#define BCM_6338_UDC0_BASE            (0xdeadbeef)
-+#define BCM_6338_UDC0_BASE            (0xfffe3000)
- #define BCM_6338_USBDMA_BASE          (0xfffe2400)
- #define BCM_6338_OHCI0_BASE           (0xdeadbeef)
- #define BCM_6338_OHCI_PRIV_BASE               (0xfffe3000)
-@@ -158,7 +158,7 @@ enum bcm63xx_regs_set {
- #define BCM_6345_UART1_BASE           (0xdeadbeef)
- #define BCM_6345_GPIO_BASE            (0xfffe0400)
- #define BCM_6345_SPI_BASE             (0xdeadbeef)
--#define BCM_6345_UDC0_BASE            (0xdeadbeef)
-+#define BCM_6345_UDC0_BASE            (0xfffe2100)
- #define BCM_6345_USBDMA_BASE          (0xfffe2800)
- #define BCM_6345_ENET0_BASE           (0xfffe1800)
- #define BCM_6345_ENETDMA_BASE         (0xfffe2800)
-@@ -215,7 +215,7 @@ enum bcm63xx_regs_set {
- #define BCM_6358_UART1_BASE           (0xfffe0120)
- #define BCM_6358_GPIO_BASE            (0xfffe0080)
- #define BCM_6358_SPI_BASE             (0xdeadbeef)
--#define BCM_6358_UDC0_BASE            (0xfffe0800)
-+#define BCM_6358_UDC0_BASE            (0xfffe0400)
- #define BCM_6358_OHCI0_BASE           (0xfffe1400)
- #define BCM_6358_OHCI_PRIV_BASE               (0xdeadbeef)
- #define BCM_6358_USBH_PRIV_BASE               (0xfffe1500)
-@@ -444,6 +444,7 @@ enum bcm63xx_irq {
-       IRQ_UART0,
-       IRQ_UART1,
-       IRQ_DSL,
-+      IRQ_UDC0,
-       IRQ_ENET0,
-       IRQ_ENET1,
-       IRQ_ENET_PHY,
-@@ -486,7 +487,7 @@ enum bcm63xx_irq {
- #define BCM_6345_UART0_IRQ            (IRQ_INTERNAL_BASE + 2)
- #define BCM_6345_DSL_IRQ              (IRQ_INTERNAL_BASE + 3)
- #define BCM_6345_ATM_IRQ              (IRQ_INTERNAL_BASE + 4)
--#define BCM_6345_USB_IRQ              (IRQ_INTERNAL_BASE + 5)
-+#define BCM_6345_UDC0_IRQ             (IRQ_INTERNAL_BASE + 5)
- #define BCM_6345_ENET0_IRQ            (IRQ_INTERNAL_BASE + 8)
- #define BCM_6345_ENET_PHY_IRQ         (IRQ_INTERNAL_BASE + 12)
- #define BCM_6345_ENET0_RXDMA_IRQ      (IRQ_INTERNAL_BASE + 13 + 1)
-@@ -508,10 +509,17 @@ enum bcm63xx_irq {
- #define BCM_6348_TIMER_IRQ            (IRQ_INTERNAL_BASE + 0)
- #define BCM_6348_UART0_IRQ            (IRQ_INTERNAL_BASE + 2)
- #define BCM_6348_DSL_IRQ              (IRQ_INTERNAL_BASE + 4)
-+#define BCM_6348_UDC0_IRQ             (IRQ_INTERNAL_BASE + 6)
- #define BCM_6348_ENET1_IRQ            (IRQ_INTERNAL_BASE + 7)
- #define BCM_6348_ENET0_IRQ            (IRQ_INTERNAL_BASE + 8)
- #define BCM_6348_ENET_PHY_IRQ         (IRQ_INTERNAL_BASE + 9)
- #define BCM_6348_OHCI0_IRQ            (IRQ_INTERNAL_BASE + 12)
-+#define BCM_6348_USB_CNTL_RX_DMA_IRQ  (IRQ_INTERNAL_BASE + 14)
-+#define BCM_6348_USB_CNTL_TX_DMA_IRQ  (IRQ_INTERNAL_BASE + 15)
-+#define BCM_6348_USB_BULK_RX_DMA_IRQ  (IRQ_INTERNAL_BASE + 16)
-+#define BCM_6348_USB_BULK_TX_DMA_IRQ  (IRQ_INTERNAL_BASE + 17)
-+#define BCM_6348_USB_ISO_RX_DMA_IRQ   (IRQ_INTERNAL_BASE + 18)
-+#define BCM_6348_USB_ISO_TX_DMA_IRQ   (IRQ_INTERNAL_BASE + 19)
- #define BCM_6348_ENET0_RXDMA_IRQ      (IRQ_INTERNAL_BASE + 20)
- #define BCM_6348_ENET0_TXDMA_IRQ      (IRQ_INTERNAL_BASE + 21)
- #define BCM_6348_ENET1_RXDMA_IRQ      (IRQ_INTERNAL_BASE + 22)
---- /dev/null
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_udc.h
-@@ -0,0 +1,6 @@
-+#ifndef BCM63XX_DEV_USB_UDC_H_
-+#define BCM63XX_DEV_USB_UDC_H_
-+
-+int bcm63xx_udc_register(void);
-+
-+#endif /* BCM63XX_DEV_USB_UDC_H_ */
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -47,6 +47,7 @@ struct board_info {
-       unsigned int    has_dsp:1;
-       unsigned int    has_uart0:1;
-       unsigned int    has_uart1:1;
-+      unsigned int    has_udc0:1;
-       /* ethernet config */
-       struct bcm63xx_enet_platform_data enet0;
---- a/arch/mips/bcm63xx/Makefile
-+++ b/arch/mips/bcm63xx/Makefile
-@@ -1,6 +1,6 @@
- obj-y         += clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \
-                  dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o dev-wdt.o \
--                 dev-usb-ohci.o dev-usb-ehci.o
-+                 dev-usb-ohci.o dev-usb-ehci.o dev-usb-udc.o
- obj-$(CONFIG_EARLY_PRINTK)    += early_printk.o
- obj-y         += boards/
---- a/arch/mips/bcm63xx/clk.c
-+++ b/arch/mips/bcm63xx/clk.c
-@@ -141,6 +141,30 @@ static struct clk clk_usbh = {
- };
- /*
-+ * USB slave clock
-+ */
-+static void usbs_set(struct clk *clk, int enable)
-+{
-+      u32 mask;
-+
-+      switch(bcm63xx_get_cpu_id()) {
-+      case BCM6338_CPU_ID:
-+              mask = CKCTL_6338_USBS_EN;
-+              break;
-+      case BCM6348_CPU_ID:
-+              mask = CKCTL_6348_USBS_EN;
-+              break;
-+      default:
-+              return;
-+      }
-+      bcm_hwclock_set(mask, enable);
-+}
-+
-+static struct clk clk_usbs = {
-+      .set    = usbs_set,
-+};
-+
-+/*
-  * SPI clock
-  */
- static void spi_set(struct clk *clk, int enable)
-@@ -208,6 +232,8 @@ struct clk *clk_get(struct device *dev,
-               return &clk_ephy;
-       if (!strcmp(id, "usbh"))
-               return &clk_usbh;
-+      if (!strcmp(id, "usbs"))
-+              return &clk_usbs;
-       if (!strcmp(id, "spi"))
-               return &clk_spi;
-       if (!strcmp(id, "periph"))
---- a/arch/mips/bcm63xx/Kconfig
-+++ b/arch/mips/bcm63xx/Kconfig
-@@ -7,6 +7,7 @@ config BCM63XX_CPU_6338
-       select USB_ARCH_HAS_OHCI
-       select USB_OHCI_BIG_ENDIAN_DESC
-       select USB_OHCI_BIG_ENDIAN_MMIO
-+      select USB_ARCH_HAS_UDC
- config BCM63XX_CPU_6345
-       bool "support 6345 CPU"
-@@ -19,6 +20,7 @@ config BCM63XX_CPU_6348
-       select USB_ARCH_HAS_OHCI
-       select USB_OHCI_BIG_ENDIAN_DESC
-       select USB_OHCI_BIG_ENDIAN_MMIO
-+      select USB_ARCH_HAS_UDC
- config BCM63XX_CPU_6358
-       bool "support 6358 CPU"
diff --git a/target/linux/brcm63xx/patches-2.6.38/200-extended-platform-devices.patch b/target/linux/brcm63xx/patches-2.6.38/200-extended-platform-devices.patch
deleted file mode 100644 (file)
index db2c22f..0000000
+++ /dev/null
@@ -1,25 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -915,6 +915,9 @@ int __init board_register_devices(void)
-       if (board.has_udc0)
-               bcm63xx_udc_register();
-+      if (board.num_devs)
-+              platform_add_devices(board.devs, board.num_devs);
-+
-       /* read base address of boot chip select (0) */
-       if (BCMCPU_IS_6345())
-               val = 0x1fc00000;
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -61,6 +61,10 @@ struct board_info {
-       /* Buttons */
-       struct gpio_button buttons[2];
-+
-+      /* Additional platform devices */
-+      struct platform_device **devs;
-+      unsigned int    num_devs;
- };
- #endif /* ! BOARD_BCM963XX_H_ */
diff --git a/target/linux/brcm63xx/patches-2.6.38/200-spi-board-info.patch b/target/linux/brcm63xx/patches-2.6.38/200-spi-board-info.patch
deleted file mode 100644 (file)
index 761ac96..0000000
+++ /dev/null
@@ -1,25 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -918,6 +918,9 @@ int __init board_register_devices(void)
-       if (board.num_devs)
-               platform_add_devices(board.devs, board.num_devs);
-+      if (board.num_spis)
-+              spi_register_board_info(board.spis, board.num_spis);
-+
-       /* read base address of boot chip select (0) */
-       if (BCMCPU_IS_6345())
-               val = 0x1fc00000;
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -65,6 +65,10 @@ struct board_info {
-       /* Additional platform devices */
-       struct platform_device **devs;
-       unsigned int    num_devs;
-+
-+      /* Additional platform devices */
-+      struct spi_board_info *spis;
-+      unsigned int    num_spis;
- };
- #endif /* ! BOARD_BCM963XX_H_ */
diff --git a/target/linux/brcm63xx/patches-2.6.38/210-no_ehci_over_current_check.patch b/target/linux/brcm63xx/patches-2.6.38/210-no_ehci_over_current_check.patch
deleted file mode 100644 (file)
index 513ff99..0000000
+++ /dev/null
@@ -1,16 +0,0 @@
---- a/drivers/usb/host/ehci-hub.c
-+++ b/drivers/usb/host/ehci-hub.c
-@@ -882,11 +882,13 @@ static int ehci_hub_control (
-                        * power switching; they're allowed to just limit the
-                        * current.  khubd will turn the power back on.
-                        */
-+#ifndef CONFIG_BCM63XX
-                       if (HCS_PPC (ehci->hcs_params)){
-                               ehci_writel(ehci,
-                                       temp & ~(PORT_RWC_BITS | PORT_POWER),
-                                       status_reg);
-                       }
-+#endif
-               }
-               /* whoever resumes must GetPortStatus to complete it!! */
diff --git a/target/linux/brcm63xx/patches-2.6.38/220-wl_exports.patch b/target/linux/brcm63xx/patches-2.6.38/220-wl_exports.patch
deleted file mode 100644 (file)
index 8cd87b8..0000000
+++ /dev/null
@@ -1,34 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -39,6 +39,13 @@ static unsigned int mac_addr_used;
- static struct board_info board;
- /*
-+ * Required export for WL
-+ */
-+#define NVRAM_SPACE 0x8000
-+char nvram_buf[NVRAM_SPACE];
-+EXPORT_SYMBOL(nvram_buf);
-+
-+/*
-  * known 6338 boards
-  */
- #ifdef CONFIG_BCM63XX_CPU_6338
-@@ -747,6 +754,7 @@ void __init board_prom_init(void)
-       /* extract nvram data */
-       memcpy(&nvram, boot_addr + BCM963XX_NVRAM_OFFSET, sizeof(nvram));
-+      memcpy(&nvram_buf, boot_addr + BCM963XX_NVRAM_OFFSET, NVRAM_SPACE);
-       /* check checksum before using data */
-       if (nvram.version <= 4)
---- a/arch/mips/mm/cache.c
-+++ b/arch/mips/mm/cache.c
-@@ -52,6 +52,7 @@ void (*_dma_cache_wback)(unsigned long s
- void (*_dma_cache_inv)(unsigned long start, unsigned long size);
- EXPORT_SYMBOL(_dma_cache_wback_inv);
-+EXPORT_SYMBOL(_dma_cache_inv);
- #endif /* CONFIG_DMA_NONCOHERENT */
diff --git a/target/linux/brcm63xx/patches-2.6.38/230-6358-enet1-external-mii-clk.patch b/target/linux/brcm63xx/patches-2.6.38/230-6358-enet1-external-mii-clk.patch
deleted file mode 100644 (file)
index d859410..0000000
+++ /dev/null
@@ -1,22 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -818,6 +818,8 @@ void __init board_prom_init(void)
-               if (BCMCPU_IS_6348())
-                       val |= GPIO_MODE_6348_G3_EXT_MII |
-                               GPIO_MODE_6348_G0_EXT_MII;
-+              else if (BCMCPU_IS_6358())
-+                      val |= GPIO_MODE_6358_ENET1_MII_CLK_INV;
-       }
-       bcm_gpio_writel(val, GPIO_MODE_REG);
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -402,6 +402,8 @@
- #define GPIO_MODE_6358_EXTRA_SPI_SS   (1 << 7)
- #define GPIO_MODE_6358_SERIAL_LED     (1 << 10)
- #define GPIO_MODE_6358_UTOPIA         (1 << 12)
-+#define GPIO_MODE_6358_ENET0_MII_CLK_INV (1 << 30)
-+#define GPIO_MODE_6358_ENET1_MII_CLK_INV (1 << 31)
- /*************************************************************************
diff --git a/target/linux/brcm63xx/patches-2.6.38/240-spi.patch b/target/linux/brcm63xx/patches-2.6.38/240-spi.patch
deleted file mode 100644 (file)
index 829fcf0..0000000
+++ /dev/null
@@ -1,1002 +0,0 @@
---- a/arch/mips/bcm63xx/cpu.c
-+++ b/arch/mips/bcm63xx/cpu.c
-@@ -58,6 +58,7 @@ static const unsigned long bcm96338_regs
- static const int bcm96338_irqs[] = {
-       [IRQ_TIMER]             = BCM_6338_TIMER_IRQ,
-+      [IRQ_SPI]               = BCM_6338_SPI_IRQ,
-       [IRQ_UART0]             = BCM_6338_UART0_IRQ,
-       [IRQ_DSL]               = BCM_6338_DSL_IRQ,
-       [IRQ_ENET0]             = BCM_6338_ENET0_IRQ,
-@@ -132,6 +133,7 @@ static const unsigned long bcm96348_regs
- static const int bcm96348_irqs[] = {
-       [IRQ_TIMER]             = BCM_6348_TIMER_IRQ,
-+      [IRQ_SPI]               = BCM_6348_SPI_IRQ,
-       [IRQ_UART0]             = BCM_6348_UART0_IRQ,
-       [IRQ_DSL]               = BCM_6348_DSL_IRQ,
-       [IRQ_ENET0]             = BCM_6348_ENET0_IRQ,
-@@ -175,6 +177,7 @@ static const unsigned long bcm96358_regs
- static const int bcm96358_irqs[] = {
-       [IRQ_TIMER]             = BCM_6358_TIMER_IRQ,
-+      [IRQ_SPI]               = BCM_6358_SPI_IRQ,
-       [IRQ_UART0]             = BCM_6358_UART0_IRQ,
-       [IRQ_UART1]             = BCM_6358_UART1_IRQ,
-       [IRQ_DSL]               = BCM_6358_DSL_IRQ,
---- /dev/null
-+++ b/arch/mips/bcm63xx/dev-spi.c
-@@ -0,0 +1,128 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2009 Florian Fainelli <florian@openwrt.org>
-+ * Copyright (C) 2010 Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/kernel.h>
-+#include <linux/platform_device.h>
-+
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_dev_spi.h>
-+#include <bcm63xx_regs.h>
-+
-+#ifdef BCMCPU_RUNTIME_DETECT
-+/*
-+ * register offsets
-+ */
-+static const unsigned long bcm96338_regs_spi[] = {
-+      [SPI_CMD]               = SPI_BCM_6338_SPI_CMD,
-+      [SPI_INT_STATUS]        = SPI_BCM_6338_SPI_INT_STATUS,
-+      [SPI_INT_MASK_ST]       = SPI_BCM_6338_SPI_MASK_INT_ST,
-+      [SPI_INT_MASK]          = SPI_BCM_6338_SPI_INT_MASK,
-+      [SPI_ST]                = SPI_BCM_6338_SPI_ST,
-+      [SPI_CLK_CFG]           = SPI_BCM_6338_SPI_CLK_CFG,
-+      [SPI_FILL_BYTE]         = SPI_BCM_6338_SPI_FILL_BYTE,
-+      [SPI_MSG_TAIL]          = SPI_BCM_6338_SPI_MSG_TAIL,
-+      [SPI_RX_TAIL]           = SPI_BCM_6338_SPI_RX_TAIL,
-+      [SPI_MSG_CTL]           = SPI_BCM_6338_SPI_MSG_CTL,
-+      [SPI_MSG_DATA]          = SPI_BCM_6338_SPI_MSG_DATA,
-+      [SPI_RX_DATA]           = SPI_BCM_6338_SPI_RX_DATA,
-+};
-+
-+static const unsigned long bcm96348_regs_spi[] = {
-+      [SPI_CMD]               = SPI_BCM_6348_SPI_CMD,
-+      [SPI_INT_STATUS]        = SPI_BCM_6348_SPI_INT_STATUS,
-+      [SPI_INT_MASK_ST]       = SPI_BCM_6348_SPI_MASK_INT_ST,
-+      [SPI_INT_MASK]          = SPI_BCM_6348_SPI_INT_MASK,
-+      [SPI_ST]                = SPI_BCM_6348_SPI_ST,
-+      [SPI_CLK_CFG]           = SPI_BCM_6348_SPI_CLK_CFG,
-+      [SPI_FILL_BYTE]         = SPI_BCM_6348_SPI_FILL_BYTE,
-+      [SPI_MSG_TAIL]          = SPI_BCM_6348_SPI_MSG_TAIL,
-+      [SPI_RX_TAIL]           = SPI_BCM_6348_SPI_RX_TAIL,
-+      [SPI_MSG_CTL]           = SPI_BCM_6348_SPI_MSG_CTL,
-+      [SPI_MSG_DATA]          = SPI_BCM_6348_SPI_MSG_DATA,
-+      [SPI_RX_DATA]           = SPI_BCM_6348_SPI_RX_DATA,
-+};
-+
-+static const unsigned long bcm96358_regs_spi[] = {
-+      [SPI_CMD]               = SPI_BCM_6358_SPI_CMD,
-+      [SPI_INT_STATUS]        = SPI_BCM_6358_SPI_INT_STATUS,
-+      [SPI_INT_MASK_ST]       = SPI_BCM_6358_SPI_MASK_INT_ST,
-+      [SPI_INT_MASK]          = SPI_BCM_6358_SPI_INT_MASK,
-+      [SPI_ST]                = SPI_BCM_6358_SPI_STATUS,
-+      [SPI_CLK_CFG]           = SPI_BCM_6358_SPI_CLK_CFG,
-+      [SPI_FILL_BYTE]         = SPI_BCM_6358_SPI_FILL_BYTE,
-+      [SPI_MSG_TAIL]          = SPI_BCM_6358_SPI_MSG_TAIL,
-+      [SPI_RX_TAIL]           = SPI_BCM_6358_SPI_RX_TAIL,
-+      [SPI_MSG_CTL]           = SPI_BCM_6358_MSG_CTL,
-+      [SPI_MSG_DATA]          = SPI_BCM_6358_SPI_MSG_DATA,
-+      [SPI_RX_DATA]           = SPI_BCM_6358_SPI_RX_DATA,
-+};
-+
-+const unsigned long *bcm63xx_regs_spi;
-+EXPORT_SYMBOL(bcm63xx_regs_spi);
-+
-+static __init void bcm63xx_spi_regs_init(void)
-+{
-+      if (BCMCPU_IS_6338())
-+              bcm63xx_regs_spi = bcm96338_regs_spi;
-+      if (BCMCPU_IS_6348())
-+              bcm63xx_regs_spi = bcm96348_regs_spi;
-+      if (BCMCPU_IS_6358())
-+              bcm63xx_regs_spi = bcm96358_regs_spi;
-+}
-+#else
-+static __init void bcm63xx_spi_regs_init(void) { }
-+#endif
-+
-+static struct resource spi_resources[] = {
-+      {
-+              .start          = -1, /* filled at runtime */
-+              .end            = -1, /* filled at runtime */
-+              .flags          = IORESOURCE_MEM,
-+      },
-+      {
-+              .start          = -1, /* filled at runtime */
-+              .flags          = IORESOURCE_IRQ,
-+      },
-+};
-+
-+static struct bcm63xx_spi_pdata spi_pdata = {
-+      .bus_num                = 0,
-+      .num_chipselect         = 8,
-+      .speed_hz               = 50000000,     /* Fclk */
-+};
-+
-+static struct platform_device bcm63xx_spi_device = {
-+      .name           = "bcm63xx-spi",
-+      .id             = 0,
-+      .num_resources  = ARRAY_SIZE(spi_resources),
-+      .resource       = spi_resources,
-+      .dev            = {
-+              .platform_data = &spi_pdata,
-+      },
-+};
-+
-+int __init bcm63xx_spi_register(void)
-+{
-+      spi_resources[0].start = bcm63xx_regset_address(RSET_SPI);
-+      spi_resources[0].end = spi_resources[0].start;
-+      spi_resources[0].end += RSET_SPI_SIZE - 1;
-+      spi_resources[1].start = bcm63xx_get_irq_number(IRQ_SPI);
-+
-+      /* Fill in platform data */
-+      if (BCMCPU_IS_6338() || BCMCPU_IS_6348())
-+              spi_pdata.fifo_size = SPI_BCM_6338_SPI_MSG_DATA_SIZE;
-+
-+      if (BCMCPU_IS_6358())
-+              spi_pdata.fifo_size = SPI_BCM_6358_SPI_MSG_DATA_SIZE;
-+
-+      bcm63xx_spi_regs_init();
-+
-+      return platform_device_register(&bcm63xx_spi_device);
-+}
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-@@ -109,6 +109,7 @@ enum bcm63xx_regs_set {
- #define RSET_WDT_SIZE                 12
- #define RSET_ENET_SIZE                        2048
- #define RSET_ENETDMA_SIZE             2048
-+#define RSET_SPI_SIZE                 256
- #define RSET_UART_SIZE                        24
- #define RSET_UDC_SIZE                 256
- #define RSET_OHCI_SIZE                        256
-@@ -214,7 +215,7 @@ enum bcm63xx_regs_set {
- #define BCM_6358_UART0_BASE           (0xfffe0100)
- #define BCM_6358_UART1_BASE           (0xfffe0120)
- #define BCM_6358_GPIO_BASE            (0xfffe0080)
--#define BCM_6358_SPI_BASE             (0xdeadbeef)
-+#define BCM_6358_SPI_BASE             (0xfffe0800)
- #define BCM_6358_UDC0_BASE            (0xfffe0400)
- #define BCM_6358_OHCI0_BASE           (0xfffe1400)
- #define BCM_6358_OHCI_PRIV_BASE               (0xdeadbeef)
-@@ -441,6 +442,7 @@ static inline unsigned long bcm63xx_regs
-  */
- enum bcm63xx_irq {
-       IRQ_TIMER = 0,
-+      IRQ_SPI,
-       IRQ_UART0,
-       IRQ_UART1,
-       IRQ_DSL,
-@@ -507,6 +509,7 @@ enum bcm63xx_irq {
-  * 6348 irqs
-  */
- #define BCM_6348_TIMER_IRQ            (IRQ_INTERNAL_BASE + 0)
-+#define BCM_6348_SPI_IRQ              (IRQ_INTERNAL_BASE + 1)
- #define BCM_6348_UART0_IRQ            (IRQ_INTERNAL_BASE + 2)
- #define BCM_6348_DSL_IRQ              (IRQ_INTERNAL_BASE + 4)
- #define BCM_6348_UDC0_IRQ             (IRQ_INTERNAL_BASE + 6)
-@@ -531,6 +534,7 @@ enum bcm63xx_irq {
-  * 6358 irqs
-  */
- #define BCM_6358_TIMER_IRQ            (IRQ_INTERNAL_BASE + 0)
-+#define BCM_6358_SPI_IRQ              (IRQ_INTERNAL_BASE + 1)
- #define BCM_6358_UART0_IRQ            (IRQ_INTERNAL_BASE + 2)
- #define BCM_6358_UART1_IRQ            (IRQ_INTERNAL_BASE + 3)
- #define BCM_6358_OHCI0_IRQ            (IRQ_INTERNAL_BASE + 5)
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -771,4 +771,116 @@
- #define DMIPSPLLCFG_N2_SHIFT          29
- #define DMIPSPLLCFG_N2_MASK           (0x7 << DMIPSPLLCFG_N2_SHIFT)
-+/*************************************************************************
-+ * _REG relative to RSET_SPI
-+ *************************************************************************/
-+
-+/* BCM 6338 SPI core */
-+#define SPI_BCM_6338_SPI_CMD          0x00    /* 16-bits register */
-+#define SPI_BCM_6338_SPI_INT_STATUS   0x02
-+#define SPI_BCM_6338_SPI_MASK_INT_ST  0x03
-+#define SPI_BCM_6338_SPI_INT_MASK     0x04
-+#define SPI_BCM_6338_SPI_ST           0x05
-+#define SPI_BCM_6338_SPI_CLK_CFG      0x06
-+#define SPI_BCM_6338_SPI_FILL_BYTE    0x07
-+#define SPI_BCM_6338_SPI_MSG_TAIL     0x09
-+#define SPI_BCM_6338_SPI_RX_TAIL      0x0b
-+#define SPI_BCM_6338_SPI_MSG_CTL      0x40
-+#define SPI_BCM_6338_SPI_MSG_DATA     0x41
-+#define SPI_BCM_6338_SPI_MSG_DATA_SIZE        0x3f
-+#define SPI_BCM_6338_SPI_RX_DATA      0x80
-+#define SPI_BCM_6338_SPI_RX_DATA_SIZE 0x3f
-+
-+/* BCM 6348 SPI core */
-+#define SPI_BCM_6348_SPI_MASK_INT_ST  0x00
-+#define SPI_BCM_6348_SPI_INT_STATUS   0x01
-+#define SPI_BCM_6348_SPI_CMD          0x02    /* 16-bits register */
-+#define SPI_BCM_6348_SPI_FILL_BYTE    0x04
-+#define SPI_BCM_6348_SPI_CLK_CFG      0x05
-+#define SPI_BCM_6348_SPI_ST           0x06
-+#define SPI_BCM_6348_SPI_INT_MASK     0x07
-+#define SPI_BCM_6348_SPI_RX_TAIL      0x08
-+#define SPI_BCM_6348_SPI_MSG_TAIL     0x10
-+#define SPI_BCM_6348_SPI_MSG_DATA     0x40
-+#define SPI_BCM_6348_SPI_MSG_CTL      0x42
-+#define SPI_BCM_6348_SPI_MSG_DATA_SIZE        0x3f
-+#define SPI_BCM_6348_SPI_RX_DATA      0x80
-+#define SPI_BCM_6348_SPI_RX_DATA_SIZE 0x3f
-+
-+/* BCM 6358 SPI core */
-+#define SPI_BCM_6358_MSG_CTL          0x00    /* 16-bits register */
-+
-+#define SPI_BCM_6358_SPI_MSG_DATA     0x02
-+#define SPI_BCM_6358_SPI_MSG_DATA_SIZE        0x21e
-+
-+#define SPI_BCM_6358_SPI_RX_DATA      0x400
-+#define SPI_BCM_6358_SPI_RX_DATA_SIZE 0x220
-+
-+#define SPI_BCM_6358_SPI_CMD          0x700   /* 16-bits register */
-+
-+#define SPI_BCM_6358_SPI_INT_STATUS   0x702
-+#define SPI_BCM_6358_SPI_MASK_INT_ST  0x703
-+
-+#define SPI_BCM_6358_SPI_INT_MASK     0x704
-+
-+#define SPI_BCM_6358_SPI_STATUS               0x705
-+
-+#define SPI_BCM_6358_SPI_CLK_CFG      0x706
-+
-+#define SPI_BCM_6358_SPI_FILL_BYTE    0x707
-+#define SPI_BCM_6358_SPI_MSG_TAIL     0x709
-+#define SPI_BCM_6358_SPI_RX_TAIL      0x70B
-+
-+/* Shared SPI definitions */
-+
-+/* Message configuration */
-+#define SPI_FD_RW                     0x00
-+#define SPI_HD_W                      0x01
-+#define SPI_HD_R                      0x02
-+#define SPI_BYTE_CNT_SHIFT            0
-+#define SPI_MSG_TYPE_SHIFT            14
-+
-+/* Command */
-+#define SPI_CMD_NOOP                  0x01
-+#define SPI_CMD_SOFT_RESET            0x02
-+#define SPI_CMD_HARD_RESET            0x04
-+#define SPI_CMD_START_IMMEDIATE               0x08
-+#define SPI_CMD_COMMAND_SHIFT         0
-+#define SPI_CMD_COMMAND_MASK          0x000f
-+#define SPI_CMD_DEVICE_ID_SHIFT               4
-+#define SPI_CMD_PREPEND_BYTE_CNT_SHIFT        8
-+#define SPI_CMD_ONE_BYTE_SHIFT                11
-+#define SPI_CMD_ONE_WIRE_SHIFT                12
-+#define SPI_DEV_ID_0                  0
-+#define SPI_DEV_ID_1                  1
-+#define SPI_DEV_ID_2                  2
-+#define SPI_DEV_ID_3                  3
-+
-+/* Interrupt mask */
-+#define SPI_INTR_CMD_DONE             0x01
-+#define SPI_INTR_RX_OVERFLOW          0x02
-+#define SPI_INTR_TX_UNDERFLOW         0x04
-+#define SPI_INTR_TX_OVERFLOW          0x08
-+#define SPI_INTR_RX_UNDERFLOW         0x10
-+#define SPI_INTR_CLEAR_ALL            0x1f
-+
-+/* Status */
-+#define SPI_RX_EMPTY                  0x02
-+#define SPI_CMD_BUSY                  0x04
-+#define SPI_SERIAL_BUSY                       0x08
-+
-+/* Clock configuration */
-+#define SPI_CLK_20MHZ                 0x00
-+#define SPI_CLK_0_391MHZ              0x01
-+#define SPI_CLK_0_781MHZ              0x02 /* default */
-+#define SPI_CLK_1_563MHZ              0x03
-+#define SPI_CLK_3_125MHZ              0x04
-+#define SPI_CLK_6_250MHZ              0x05
-+#define SPI_CLK_12_50MHZ              0x06
-+#define SPI_CLK_25MHZ                 0x07
-+#define SPI_CLK_MASK                  0x07
-+#define SPI_SSOFFTIME_MASK            0x38
-+#define SPI_SSOFFTIME_SHIFT           3
-+#define SPI_BYTE_SWAP                 0x80
-+
- #endif /* BCM63XX_REGS_H_ */
---- /dev/null
-+++ b/drivers/spi/bcm63xx_spi.c
-@@ -0,0 +1,496 @@
-+/*
-+ * Broadcom BCM63xx SPI controller support
-+ *
-+ * Copyright (C) 2009 Florian Fainelli <florian@openwrt.org>
-+ * Copyright (C) 2010 Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License
-+ * as published by the Free Software Foundation; either version 2
-+ * of the License, or (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the
-+ * Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor,
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/clk.h>
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+#include <linux/delay.h>
-+#include <linux/interrupt.h>
-+#include <linux/spi/spi.h>
-+#include <linux/completion.h>
-+#include <linux/err.h>
-+
-+#include <bcm63xx_dev_spi.h>
-+
-+#define PFX           KBUILD_MODNAME
-+#define DRV_VER               "0.1.2"
-+
-+struct bcm63xx_spi {
-+      spinlock_t              lock;
-+      int                     stopping;
-+        struct completion     done;
-+
-+      void __iomem            *regs;
-+      int                     irq;
-+
-+      /* Platform data */
-+        u32                   speed_hz;
-+      unsigned                fifo_size;
-+
-+      /* Data buffers */
-+      const unsigned char     *tx_ptr;
-+      unsigned char           *rx_ptr;
-+
-+      /* data iomem */
-+      u8 __iomem              *tx_io;
-+      const u8 __iomem        *rx_io;
-+
-+      int                     remaining_bytes;
-+
-+      struct clk              *clk;
-+      struct platform_device  *pdev;
-+};
-+
-+static inline u8 bcm_spi_readb(struct bcm63xx_spi *bs,
-+                              unsigned int offset)
-+{
-+      return bcm_readw(bs->regs + bcm63xx_spireg(offset));
-+}
-+
-+static inline u16 bcm_spi_readw(struct bcm63xx_spi *bs,
-+                              unsigned int offset)
-+{
-+      return bcm_readw(bs->regs + bcm63xx_spireg(offset));
-+}
-+
-+static inline void bcm_spi_writeb(struct bcm63xx_spi *bs,
-+                                u8 value, unsigned int offset)
-+{
-+      bcm_writeb(value, bs->regs + bcm63xx_spireg(offset));
-+}
-+
-+static inline void bcm_spi_writew(struct bcm63xx_spi *bs,
-+                                u16 value, unsigned int offset)
-+{
-+      bcm_writew(value, bs->regs + bcm63xx_spireg(offset));
-+}
-+
-+static int bcm63xx_spi_setup_transfer(struct spi_device *spi,
-+                                    struct spi_transfer *t)
-+{
-+      u8 bits_per_word;
-+      u8 clk_cfg;
-+      u32 hz;
-+      unsigned int div;
-+
-+      struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
-+
-+      bits_per_word = (t) ? t->bits_per_word : spi->bits_per_word;
-+      hz = (t) ? t->speed_hz : spi->max_speed_hz;
-+      if (bits_per_word != 8) {
-+              dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n",
-+                      __func__, bits_per_word);
-+              return -EINVAL;
-+        }
-+
-+      if (spi->chip_select > spi->master->num_chipselect) {
-+              dev_err(&spi->dev, "%s, unsupported slave %d\n",
-+                      __func__, spi->chip_select);
-+              return -EINVAL;
-+      }
-+
-+      /* Check clock setting */
-+      div = (bs->speed_hz / hz);
-+      switch (div) {
-+      case 2:
-+              clk_cfg = SPI_CLK_25MHZ;
-+              break;
-+      case 4:
-+              clk_cfg = SPI_CLK_12_50MHZ;
-+              break;
-+      case 8:
-+              clk_cfg = SPI_CLK_6_250MHZ;
-+              break;
-+      case 16:
-+              clk_cfg = SPI_CLK_3_125MHZ;
-+              break;
-+      case 32:
-+              clk_cfg = SPI_CLK_1_563MHZ;
-+              break;
-+      case 64:
-+              clk_cfg = SPI_CLK_0_781MHZ;
-+              break;
-+      case 128:
-+      default:
-+              /* Set to slowest mode for compatibility */
-+              clk_cfg = SPI_CLK_0_391MHZ;
-+              break;
-+      }
-+
-+      bcm_spi_writeb(bs, clk_cfg, SPI_CLK_CFG);
-+      dev_dbg(&spi->dev, "Setting clock register to %d (hz %d, cmd %02x)\n",
-+              div, hz, clk_cfg);
-+
-+      return 0;
-+}
-+
-+/* the spi->mode bits understood by this driver: */
-+#define MODEBITS (SPI_CPOL | SPI_CPHA)
-+
-+static int bcm63xx_spi_setup(struct spi_device *spi)
-+{
-+      struct bcm63xx_spi *bs;
-+      int ret;
-+
-+      bs = spi_master_get_devdata(spi->master);
-+
-+      if (bs->stopping)
-+              return -ESHUTDOWN;
-+
-+      if (!spi->bits_per_word)
-+              spi->bits_per_word = 8;
-+
-+      if (spi->mode & ~MODEBITS) {
-+              dev_err(&spi->dev, "%s, unsupported mode bits %x\n",
-+                      __func__, spi->mode & ~MODEBITS);
-+              return -EINVAL;
-+      }
-+
-+      ret = bcm63xx_spi_setup_transfer(spi, NULL);
-+      if (ret < 0) {
-+              dev_err(&spi->dev, "setup: unsupported mode bits %x\n",
-+                      spi->mode & ~MODEBITS);
-+              return ret;
-+      }
-+
-+      dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u nsec/bit\n",
-+              __func__, spi->mode & MODEBITS, spi->bits_per_word, 0);
-+
-+      return 0;
-+}
-+
-+/* Fill the TX FIFO with as many bytes as possible */
-+static void bcm63xx_spi_fill_tx_fifo(struct bcm63xx_spi *bs)
-+{
-+      u8 size;
-+
-+        /* Fill the Tx FIFO with as many bytes as possible */
-+      size = bs->remaining_bytes < bs->fifo_size ? bs->remaining_bytes :
-+              bs->fifo_size;
-+      memcpy_toio(bs->tx_io, bs->tx_ptr, size);
-+      bs->remaining_bytes -= size;
-+}
-+
-+static int bcm63xx_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
-+{
-+      struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
-+      u16 msg_ctl;
-+      u16 cmd;
-+
-+      dev_dbg(&spi->dev, "txrx: tx %p, rx %p, len %d\n",
-+              t->tx_buf, t->rx_buf, t->len);
-+
-+      /* Transmitter is inhibited */
-+      bs->tx_ptr = t->tx_buf;
-+      bs->rx_ptr = t->rx_buf;
-+      init_completion(&bs->done);
-+
-+      if (t->tx_buf) {
-+              bs->remaining_bytes = t->len;
-+              bcm63xx_spi_fill_tx_fifo(bs);
-+      }
-+
-+      /* Enable the command done interrupt which
-+       * we use to determine completion of a command */
-+      bcm_spi_writeb(bs, SPI_INTR_CMD_DONE, SPI_INT_MASK);
-+
-+      /* Fill in the Message control register */
-+      msg_ctl = (t->len << SPI_BYTE_CNT_SHIFT);
-+
-+      if (t->rx_buf && t->tx_buf)
-+              msg_ctl |= (SPI_FD_RW << SPI_MSG_TYPE_SHIFT);
-+      else if (t->rx_buf)
-+              msg_ctl |= (SPI_HD_R << SPI_MSG_TYPE_SHIFT);
-+      else if (t->tx_buf)
-+              msg_ctl |= (SPI_HD_W << SPI_MSG_TYPE_SHIFT);
-+
-+      bcm_spi_writew(bs, msg_ctl, SPI_MSG_CTL);
-+
-+      /* Issue the transfer */
-+      cmd = SPI_CMD_START_IMMEDIATE;
-+      cmd |= (0 << SPI_CMD_PREPEND_BYTE_CNT_SHIFT);
-+      cmd |= (spi->chip_select << SPI_CMD_DEVICE_ID_SHIFT);
-+      bcm_spi_writew(bs, cmd, SPI_CMD);
-+      wait_for_completion(&bs->done);
-+
-+      /* Disable the CMD_DONE interrupt */
-+      bcm_spi_writeb(bs, 0, SPI_INT_MASK);
-+
-+      return t->len - bs->remaining_bytes;
-+}
-+
-+static int bcm63xx_transfer(struct spi_device *spi, struct spi_message *m)
-+{
-+      struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
-+      struct spi_transfer *t;
-+      int ret = 0;
-+
-+      if (unlikely(list_empty(&m->transfers)))
-+              return -EINVAL;
-+
-+      if (bs->stopping)
-+              return -ESHUTDOWN;
-+
-+      list_for_each_entry(t, &m->transfers, transfer_list) {
-+              ret += bcm63xx_txrx_bufs(spi, t);
-+      }
-+
-+      m->complete(m->context);
-+
-+      return ret;
-+}
-+
-+/* This driver supports single master mode only. Hence
-+ * CMD_DONE is the only interrupt we care about
-+ */
-+static irqreturn_t bcm63xx_spi_interrupt(int irq, void *dev_id)
-+{
-+      struct spi_master *master = (struct spi_master *)dev_id;
-+      struct bcm63xx_spi *bs = spi_master_get_devdata(master);
-+      u8 intr;
-+      u16 cmd;
-+
-+      /* Read interupts and clear them immediately */
-+      intr = bcm_spi_readb(bs, SPI_INT_STATUS);
-+      bcm_spi_writeb(bs, SPI_INTR_CLEAR_ALL, SPI_INT_STATUS);
-+      bcm_spi_writeb(bs, 0, SPI_INT_MASK);
-+
-+      /* A tansfer completed */
-+      if (intr & SPI_INTR_CMD_DONE) {
-+              u8 rx_tail;
-+
-+              rx_tail = bcm_spi_readb(bs, SPI_RX_TAIL);
-+
-+              /* Read out all the data */
-+              if (rx_tail)
-+                      memcpy_fromio(bs->rx_ptr, bs->rx_io, rx_tail);
-+
-+              /* See if there is more data to send */
-+              if (bs->remaining_bytes > 0) {
-+                      bcm63xx_spi_fill_tx_fifo(bs);
-+
-+                      /* Start the transfer */
-+                      bcm_spi_writew(bs, SPI_HD_W << SPI_MSG_TYPE_SHIFT,
-+                                     SPI_MSG_CTL);
-+                      cmd = bcm_spi_readw(bs, SPI_CMD);
-+                      cmd |= SPI_CMD_START_IMMEDIATE;
-+                      cmd |= (0 << SPI_CMD_PREPEND_BYTE_CNT_SHIFT);
-+                      bcm_spi_writeb(bs, SPI_INTR_CMD_DONE, SPI_INT_MASK);
-+                      bcm_spi_writew(bs, cmd, SPI_CMD);
-+              } else {
-+                      complete(&bs->done);
-+              }
-+      }
-+
-+      return IRQ_HANDLED;
-+}
-+
-+
-+static int __init bcm63xx_spi_probe(struct platform_device *pdev)
-+{
-+      struct resource *r;
-+      struct device *dev = &pdev->dev;
-+      struct bcm63xx_spi_pdata *pdata = pdev->dev.platform_data;
-+      int irq;
-+      struct spi_master *master;
-+      struct clk *clk;
-+      struct bcm63xx_spi *bs;
-+      int ret;
-+
-+      r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+      if (!r) {
-+              dev_err(dev, "no iomem\n");
-+              ret = -ENXIO;
-+              goto out;
-+      }
-+
-+      irq = platform_get_irq(pdev, 0);
-+      if (irq < 0) {
-+              dev_err(dev, "no irq\n");
-+              ret = -ENXIO;
-+              goto out;
-+      }
-+
-+      clk = clk_get(dev, "spi");
-+      if (IS_ERR(clk)) {
-+              dev_err(dev, "no clock for device\n");
-+              ret = -ENODEV;
-+              goto out;
-+      }
-+
-+      master = spi_alloc_master(dev, sizeof(*bs));
-+      if (!master) {
-+              dev_err(dev, "out of memory\n");
-+              ret = -ENOMEM;
-+              goto out_free;
-+      }
-+
-+      bs = spi_master_get_devdata(master);
-+      init_completion(&bs->done);
-+
-+      platform_set_drvdata(pdev, master);
-+      bs->pdev = pdev;
-+
-+      if (!request_mem_region(r->start, r->end - r->start, PFX)) {
-+              dev_err(dev, "iomem request failed\n");
-+              ret = -ENXIO;
-+              goto out_put_master;
-+      }
-+
-+      bs->regs = ioremap_nocache(r->start, r->end - r->start);
-+      if (!bs->regs) {
-+              dev_err(dev, "unable to ioremap regs\n");
-+              ret = -ENOMEM;
-+              goto out_put_master;
-+      }
-+      bs->irq = irq;
-+      bs->clk = clk;
-+      bs->fifo_size = pdata->fifo_size;
-+
-+      ret = request_irq(irq, bcm63xx_spi_interrupt, 0, pdev->name, master);
-+      if (ret) {
-+              dev_err(dev, "unable to request irq\n");
-+              goto out_unmap;
-+      }
-+
-+      master->bus_num = pdata->bus_num;
-+      master->num_chipselect = pdata->num_chipselect;
-+      master->setup = bcm63xx_spi_setup;
-+      master->transfer = bcm63xx_transfer;
-+      bs->speed_hz = pdata->speed_hz;
-+      bs->stopping = 0;
-+      bs->tx_io = (u8*)(bs->regs + bcm63xx_spireg(SPI_MSG_DATA));
-+      bs->rx_io = (const u8*)(bs->regs + bcm63xx_spireg(SPI_RX_DATA));
-+      spin_lock_init(&bs->lock);
-+
-+      /* Initialize hardware */
-+      clk_enable(bs->clk);
-+      bcm_spi_writeb(bs, SPI_INTR_CLEAR_ALL, SPI_INT_STATUS);
-+
-+      /* register and we are done */
-+      ret = spi_register_master(master);
-+      if (ret) {
-+              dev_err(dev, "spi register failed\n");
-+              goto out_reset_hw;
-+      }
-+
-+      dev_info(dev, "at 0x%08x (irq %d, FIFOs size %d) v%s\n",
-+               r->start, irq, bs->fifo_size, DRV_VER);
-+
-+      return 0;
-+
-+out_reset_hw:
-+      clk_disable(clk);
-+      free_irq(irq, master);
-+out_unmap:
-+      iounmap(bs->regs);
-+out_put_master:
-+      spi_master_put(master);
-+out_free:
-+      clk_put(clk);
-+out:
-+      return ret;
-+}
-+
-+static int __exit bcm63xx_spi_remove(struct platform_device *pdev)
-+{
-+      struct spi_master       *master = platform_get_drvdata(pdev);
-+      struct bcm63xx_spi      *bs = spi_master_get_devdata(master);
-+      struct resource         *r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+
-+      /* reset spi block */
-+      bcm_spi_writeb(bs, 0, SPI_INT_MASK);
-+      spin_lock(&bs->lock);
-+      bs->stopping = 1;
-+
-+      /* HW shutdown */
-+      clk_disable(bs->clk);
-+      clk_put(bs->clk);
-+
-+      spin_unlock(&bs->lock);
-+
-+      free_irq(bs->irq, master);
-+      iounmap(bs->regs);
-+      release_mem_region(r->start, r->end - r->start);
-+      platform_set_drvdata(pdev, 0);
-+      spi_unregister_master(master);
-+
-+      return 0;
-+}
-+
-+#ifdef CONFIG_PM
-+static int bcm63xx_spi_suspend(struct platform_device *pdev, pm_message_t mesg)
-+{
-+      struct spi_master       *master = platform_get_drvdata(pdev);
-+      struct bcm63xx_spi      *bs = spi_master_get_devdata(master);
-+
-+        clk_disable(bs->clk);
-+
-+      return 0;
-+}
-+
-+static int bcm63xx_spi_resume(struct platform_device *pdev)
-+{
-+      struct spi_master       *master = platform_get_drvdata(pdev);
-+      struct bcm63xx_spi      *bs = spi_master_get_devdata(master);
-+
-+      clk_enable(bs->clk);
-+
-+      return 0;
-+}
-+#else
-+#define bcm63xx_spi_suspend   NULL
-+#define bcm63xx_spi_resume    NULL
-+#endif
-+
-+static struct platform_driver bcm63xx_spi_driver = {
-+      .driver = {
-+              .name   = "bcm63xx-spi",
-+              .owner  = THIS_MODULE,
-+      },
-+      .probe          = bcm63xx_spi_probe,
-+      .remove         = __exit_p(bcm63xx_spi_remove),
-+      .suspend        = bcm63xx_spi_suspend,
-+      .resume         = bcm63xx_spi_resume,
-+};
-+
-+
-+static int __init bcm63xx_spi_init(void)
-+{
-+      return platform_driver_register(&bcm63xx_spi_driver);
-+}
-+
-+static void __exit bcm63xx_spi_exit(void)
-+{
-+      platform_driver_unregister(&bcm63xx_spi_driver);
-+}
-+
-+module_init(bcm63xx_spi_init);
-+module_exit(bcm63xx_spi_exit);
-+
-+MODULE_ALIAS("platform:bcm63xx_spi");
-+MODULE_AUTHOR("Florian Fainelli <florian@openwrt.org>");
-+MODULE_AUTHOR("Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>");
-+MODULE_DESCRIPTION("Broadcom BCM63xx SPI Controller driver");
-+MODULE_LICENSE("GPL");
-+MODULE_VERSION(DRV_VER);
---- a/drivers/spi/Kconfig
-+++ b/drivers/spi/Kconfig
-@@ -68,6 +68,12 @@ config SPI_ATMEL
-         This selects a driver for the Atmel SPI Controller, present on
-         many AT32 (AVR32) and AT91 (ARM) chips.
-+config SPI_BCM63XX
-+      tristate "Broadcom BCM63xx SPI controller"
-+      depends on BCM63XX
-+      help
-+        This is the SPI controller master driver for Broadcom BCM63xx SoC.
-+
- config SPI_BFIN
-       tristate "SPI controller driver for ADI Blackfin5xx"
-       depends on BLACKFIN
---- a/drivers/spi/Makefile
-+++ b/drivers/spi/Makefile
-@@ -51,6 +51,7 @@ obj-$(CONFIG_SPI_SH_SCI)             += spi_sh_sci.
- obj-$(CONFIG_SPI_SH_MSIOF)            += spi_sh_msiof.o
- obj-$(CONFIG_SPI_STMP3XXX)            += spi_stmp.o
- obj-$(CONFIG_SPI_NUC900)              += spi_nuc900.o
-+obj-$(CONFIG_SPI_BCM63XX)             += bcm63xx_spi.o
- # special build for s3c24xx spi driver with fiq support
- spi_s3c24xx_hw-y                      := spi_s3c24xx.o
---- /dev/null
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
-@@ -0,0 +1,126 @@
-+#ifndef BCM63XX_DEV_SPI_H
-+#define BCM63XX_DEV_SPI_H
-+
-+#include <linux/types.h>
-+#include <bcm63xx_io.h>
-+#include <bcm63xx_regs.h>
-+
-+int __init bcm63xx_spi_register(void);
-+
-+struct bcm63xx_spi_pdata {
-+      unsigned int    fifo_size;
-+      int             bus_num;
-+      int             num_chipselect;
-+      u32             speed_hz;
-+};
-+
-+enum bcm63xx_regs_spi {
-+        SPI_CMD,
-+        SPI_INT_STATUS,
-+        SPI_INT_MASK_ST,
-+        SPI_INT_MASK,
-+        SPI_ST,
-+        SPI_CLK_CFG,
-+        SPI_FILL_BYTE,
-+        SPI_MSG_TAIL,
-+        SPI_RX_TAIL,
-+        SPI_MSG_CTL,
-+        SPI_MSG_DATA,
-+        SPI_RX_DATA,
-+};
-+
-+static inline unsigned long bcm63xx_spireg(enum bcm63xx_regs_spi reg)
-+{
-+#ifdef BCMCPU_RUNTIME_DETECT
-+      extern const unsigned long *bcm63xx_regs_spi;
-+        return bcm63xx_regs_spi[reg];
-+#else
-+#ifdef CONFIG_BCM63XX_CPU_6338
-+switch (reg) {
-+      case SPI_CMD:
-+              return SPI_BCM_6338_SPI_CMD;
-+      case SPI_INT_STATUS:
-+              return SPI_BCM_6338_SPI_INT_STATUS;
-+      case SPI_INT_MASK_ST:
-+              return SPI_BCM_6338_SPI_MASK_INT_ST;
-+      case SPI_INT_MASK:
-+              return SPI_BCM_6338_SPI_INT_MASK;
-+      case SPI_ST:
-+              return SPI_BCM_6338_SPI_ST;
-+      case SPI_CLK_CFG:
-+              return SPI_BCM_6338_SPI_CLK_CFG;
-+      case SPI_FILL_BYTE:
-+              return SPI_BCM_6338_SPI_FILL_BYTE;
-+      case SPI_MSG_TAIL:
-+              return SPI_BCM_6338_SPI_MSG_TAIL;
-+      case SPI_RX_TAIL:
-+              return SPI_BCM_6338_SPI_RX_TAIL;
-+      case SPI_MSG_CTL:
-+              return SPI_BCM_6338_SPI_MSG_CTL;
-+      case SPI_MSG_DATA:
-+              return SPI_BCM_6338_SPI_MSG_DATA;
-+      case SPI_RX_DATA:
-+              return SPI_BCM_6338_SPI_RX_DATA;
-+}
-+#endif
-+#ifdef CONFIG_BCM63XX_CPU_6348
-+switch (reg) {
-+      case SPI_CMD:
-+              return SPI_BCM_6348_SPI_CMD;
-+      case SPI_INT_MASK_ST:
-+              return SPI_BCM_6348_SPI_MASK_INT_ST;
-+      case SPI_INT_MASK:
-+              return SPI_BCM_6348_SPI_INT_MASK;
-+      case SPI_INT_STATUS:
-+              return SPI_BCM_6348_SPI_INT_STATUS;
-+      case SPI_ST:
-+              return SPI_BCM_6348_SPI_ST;
-+      case SPI_CLK_CFG:
-+              return SPI_BCM_6348_SPI_CLK_CFG;
-+      case SPI_FILL_BYTE:
-+              return SPI_BCM_6348_SPI_FILL_BYTE;
-+      case SPI_MSG_TAIL:
-+              return SPI_BCM_6348_SPI_MSG_TAIL;
-+      case SPI_RX_TAIL:
-+              return SPI_BCM_6348_SPI_RX_TAIL;
-+      case SPI_MSG_CTL:
-+              return SPI_BCM_6348_SPI_MSG_CTL;
-+      case SPI_MSG_DATA:
-+              return SPI_BCM_6348_SPI_MSG_DATA;
-+      case SPI_RX_DATA:
-+              return SPI_BCM_6348_SPI_RX_DATA;
-+}
-+#endif
-+#ifdef CONFIG_BCM63XX_CPU_6358
-+switch (reg) {
-+      case SPI_CMD:
-+              return SPI_BCM_6358_SPI_CMD;
-+      case SPI_INT_STATUS:
-+              return SPI_BCM_6358_SPI_INT_STATUS;
-+      case SPI_INT_MASK_ST:
-+              return SPI_BCM_6358_SPI_MASK_INT_ST;
-+      case SPI_INT_MASK:
-+              return SPI_BCM_6358_SPI_INT_MASK;
-+      case SPI_ST:
-+              return SPI_BCM_6358_SPI_STATUS;
-+      case SPI_CLK_CFG:
-+              return SPI_BCM_6358_SPI_CLK_CFG;
-+      case SPI_FILL_BYTE:
-+              return SPI_BCM_6358_SPI_FILL_BYTE;
-+      case SPI_MSG_TAIL:
-+              return SPI_BCM_6358_SPI_MSG_TAIL;
-+      case SPI_RX_TAIL:
-+              return SPI_BCM_6358_SPI_RX_TAIL;
-+      case SPI_MSG_CTL:
-+              return SPI_BCM_6358_MSG_CTL;
-+      case SPI_MSG_DATA:
-+              return SPI_BCM_6358_SPI_MSG_DATA;
-+      case SPI_RX_DATA:
-+              return SPI_BCM_6358_SPI_RX_DATA;
-+}
-+#endif
-+#endif
-+      return 0;
-+}
-+
-+#endif /* BCM63XX_DEV_SPI_H */
---- a/arch/mips/bcm63xx/Makefile
-+++ b/arch/mips/bcm63xx/Makefile
-@@ -1,6 +1,6 @@
- obj-y         += clk.o cpu.o cs.o gpio.o irq.o prom.o setup.o timer.o \
-                  dev-dsp.o dev-enet.o dev-pcmcia.o dev-uart.o dev-wdt.o \
--                 dev-usb-ohci.o dev-usb-ehci.o dev-usb-udc.o
-+                 dev-usb-ohci.o dev-usb-ehci.o dev-usb-udc.o dev-spi.o
- obj-$(CONFIG_EARLY_PRINTK)    += early_printk.o
- obj-y         += boards/
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -30,6 +30,7 @@
- #include <bcm63xx_dev_usb_ohci.h>
- #include <bcm63xx_dev_usb_ehci.h>
- #include <bcm63xx_dev_usb_udc.h>
-+#include <bcm63xx_dev_spi.h>
- #include <board_bcm963xx.h>
- #define PFX   "board_bcm963xx: "
-@@ -931,6 +932,9 @@ int __init board_register_devices(void)
-       if (board.num_spis)
-               spi_register_board_info(board.spis, board.num_spis);
-+      if (!BCMCPU_IS_6345())
-+              bcm63xx_spi_register();
-+
-       /* read base address of boot chip select (0) */
-       if (BCMCPU_IS_6345())
-               val = 0x1fc00000;
diff --git a/target/linux/brcm63xx/patches-2.6.38/250-boardid_fixup.patch b/target/linux/brcm63xx/patches-2.6.38/250-boardid_fixup.patch
deleted file mode 100644 (file)
index 50e8016..0000000
+++ /dev/null
@@ -1,58 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -32,9 +32,13 @@
- #include <bcm63xx_dev_usb_udc.h>
- #include <bcm63xx_dev_spi.h>
- #include <board_bcm963xx.h>
-+#include <bcm_tag.h>
- #define PFX   "board_bcm963xx: "
-+#define CFE_OFFSET_64K                0x10000
-+#define CFE_OFFSET_128K               0x20000
-+
- static struct bcm963xx_nvram nvram;
- static unsigned int mac_addr_used;
- static struct board_info board;
-@@ -723,6 +727,29 @@ static int board_get_mac_address(u8 *mac
-       return 0;
- }
-+static void __init boardid_fixup(u8 *boot_addr)
-+{
-+      struct bcm_tag *tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_64K);
-+
-+      /* check if bcm_tag is at 64k offset */
-+      if (strncmp(nvram.name, tag->boardid, BOARDID_LEN) != 0) {
-+              /* else try 128k */
-+              tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_128K);
-+              if (strncmp(nvram.name, tag->boardid, BOARDID_LEN) != 0) {
-+                      /* No tag found */
-+                      printk(KERN_DEBUG "No bcm_tag found!\n");
-+                      return;
-+              }
-+      }
-+      /* check if we should override the boardid */
-+      if (tag->information1[0] != '+')
-+              return;
-+
-+      strncpy(nvram.name, &tag->information1[1], BOARDID_LEN);
-+
-+      printk(KERN_INFO "Overriding boardid with '%s'\n", nvram.name);
-+}
-+
- /*
-  * early init callback, read nvram data from flash and checksum it
-  */
-@@ -771,6 +798,11 @@ void __init board_prom_init(void)
-               return;
-       }
-+      if (strcmp(cfe_version, "unknown") != 0) {
-+              /* cfe present */
-+              boardid_fixup(boot_addr);
-+      }
-+
-       /* find board by name */
-       for (i = 0; i < ARRAY_SIZE(bcm963xx_boards); i++) {
-               if (strncmp(nvram.name, bcm963xx_boards[i]->name,
diff --git a/target/linux/brcm63xx/patches-2.6.38/300-alice_gate2_leds.patch b/target/linux/brcm63xx/patches-2.6.38/300-alice_gate2_leds.patch
deleted file mode 100644 (file)
index f54fab7..0000000
+++ /dev/null
@@ -1,113 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -603,6 +603,99 @@ static struct board_info __initdata boar
-       .has_ohci0 = 1,
-       .has_ehci0 = 1,
-+
-+      .leds = {
-+              /*Each led on alice gate is bi-color */
-+              {
-+                      .name           = "power:red",
-+                      .gpio           = 5,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "power:green",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+              {
-+                      .name           = "service:red",
-+                      .gpio           = 7,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:green",
-+                      .gpio           = 6,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "adsl:red",
-+                      .gpio           = 9,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "adsl:green",
-+                      .gpio           = 10,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi:red",
-+                      .gpio           = 23,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi:green",
-+                      .gpio           = 22,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "internet:red",
-+                      .gpio           = 25,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "internet:green",
-+                      .gpio           = 24,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "usr1:red",
-+                      .gpio           = 27,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "usr1:green",
-+                      .gpio           = 26,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "usr2:red",
-+                      .gpio           = 30,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "usr2:green",
-+                      .gpio           = 29,
-+                      .active_low     = 1,
-+              },
-+      },
-+
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 37,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+              {
-+                      .desc           = "wps",
-+                      .gpio           = 34,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_WPS_BUTTON,
-+                      .threshold      = 3,
-+              },
-+      },
- };
- static struct board_info __initdata board_DWVS0 = {
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -57,7 +57,7 @@ struct board_info {
-       struct bcm63xx_dsp_platform_data dsp;
-       /* GPIO LEDs */
--      struct gpio_led leds[5];
-+      struct gpio_led leds[14];
-       /* Buttons */
-       struct gpio_button buttons[2];
diff --git a/target/linux/brcm63xx/patches-2.6.38/310-96348gw_a_leds.patch b/target/linux/brcm63xx/patches-2.6.38/310-96348gw_a_leds.patch
deleted file mode 100644 (file)
index 7c5027f..0000000
+++ /dev/null
@@ -1,22 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -475,6 +475,19 @@ static struct board_info __initdata boar
-       },
-       .has_ohci0 = 1,
-+
-+      .leds = {
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = 3,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "usb",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+              }
-+      },
- };
- #endif
diff --git a/target/linux/brcm63xx/patches-2.6.38/440-board-D4PW.patch b/target/linux/brcm63xx/patches-2.6.38/440-board-D4PW.patch
deleted file mode 100644 (file)
index 07f6159..0000000
+++ /dev/null
@@ -1,66 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -489,6 +489,55 @@ static struct board_info __initdata boar
-               }
-       },
- };
-+
-+static struct board_info __initdata board_96348_D4PW = {
-+      .name                           = "D-4P-W",
-+      .expected_cpu_id                = 0x6348,
-+
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+      .has_uart0                      = 1,
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .leds = {
-+              {
-+                      .name           = "power:green",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "status",
-+                      .gpio           = 3,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "internet:green",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "internet:red",
-+                      .gpio           = 5,
-+                      .active_low     = 1,
-+              },
-+      },
-+
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 7,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
- #endif
- /*
-@@ -753,6 +802,7 @@ static const struct board_info __initdat
-       &board_DV201AMR,
-       &board_96348gw_a,
-       &board_rta1025w_16,
-+      &board_96348_D4PW,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6358
diff --git a/target/linux/brcm63xx/patches-2.6.38/441-board-NB4.patch b/target/linux/brcm63xx/patches-2.6.38/441-board-NB4.patch
deleted file mode 100644 (file)
index 2fb7ff2..0000000
+++ /dev/null
@@ -1,569 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -17,6 +17,9 @@
- #include <linux/ssb/ssb.h>
- #include <linux/gpio_buttons.h>
- #include <linux/input.h>
-+#include <linux/spi/spi.h>
-+#include <linux/spi/spi_gpio.h>
-+#include <linux/spi/74x164.h>
- #include <asm/addrspace.h>
- #include <bcm63xx_board.h>
- #include <bcm63xx_cpu.h>
-@@ -39,6 +42,12 @@
- #define CFE_OFFSET_64K                0x10000
- #define CFE_OFFSET_128K               0x20000
-+#define NB4_PID_OFFSET                0xff80
-+#define NB4_74X164_GPIO_BASE  64
-+#define NB4_SPI_GPIO_MOSI     7
-+#define NB4_SPI_GPIO_CLK      6
-+#define NB4_74HC64_GPIO(X)    (NB4_74X164_GPIO_BASE + (X))
-+
- static struct bcm963xx_nvram nvram;
- static unsigned int mac_addr_used;
- static struct board_info board;
-@@ -780,6 +789,502 @@ static struct board_info __initdata boar
-       .has_ohci0                      = 1,
- };
-+
-+struct spi_gpio_platform_data nb4_spi_gpio_data = {
-+      .sck            = NB4_SPI_GPIO_CLK,
-+      .mosi           = NB4_SPI_GPIO_MOSI,
-+      .miso           = SPI_GPIO_NO_MISO,
-+      .num_chipselect = 1,
-+};
-+
-+
-+static struct platform_device nb4_spi_gpio = {
-+      .name = "spi_gpio",
-+      .id   = 1,
-+      .dev = {
-+              .platform_data = &nb4_spi_gpio_data,
-+      },
-+};
-+
-+static struct platform_device * __initdata nb4_devices[] = {
-+      &nb4_spi_gpio,
-+};
-+
-+const struct gen_74x164_chip_platform_data nb4_74x164_platform_data = {
-+      .base = NB4_74X164_GPIO_BASE
-+};
-+
-+static struct spi_board_info nb4_spi_devices[] = {
-+      {
-+              .modalias = "74x164",
-+              .max_speed_hz = 781000,
-+              .bus_num = 1,
-+              .controller_data = (void *) SPI_GPIO_NO_CHIPSELECT,
-+              .mode = SPI_MODE_0,
-+              .platform_data = &nb4_74x164_platform_data
-+      }
-+};
-+
-+static struct board_info __initdata board_nb4_ser_r0 = {
-+      .name                           = "NB4-SER-r0",
-+      .expected_cpu_id                = 0x6358,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+
-+      .has_ohci0 = 1,
-+      .has_pccard = 1,
-+      .has_ehci0 = 1,
-+
-+      .has_udc0                       = 1,
-+
-+      .leds = {
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = NB4_74HC64_GPIO(4),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "traffic",
-+                      .gpio           = 2,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tel",
-+                      .gpio           = NB4_74HC64_GPIO(3),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tv",
-+                      .gpio           = NB4_74HC64_GPIO(2),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi",
-+                      .gpio           = 15,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "alarm",
-+                      .gpio           = NB4_74HC64_GPIO(0),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:red",
-+                      .gpio           = 29,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:green",
-+                      .gpio           = 30,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:blue",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+      },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 34,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+              {
-+                      .desc           = "wps",
-+                      .gpio           = 37,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_WPS_BUTTON,
-+                      .threshold      = 3,
-+              },
-+      },
-+      .devs = nb4_devices,
-+      .num_devs = ARRAY_SIZE(nb4_devices),
-+      .spis = nb4_spi_devices,
-+      .num_spis = ARRAY_SIZE(nb4_spi_devices),
-+};
-+
-+static struct board_info __initdata board_nb4_ser_r1 = {
-+      .name                           = "NB4-SER-r1",
-+      .expected_cpu_id                = 0x6358,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+
-+      .has_ohci0 = 1,
-+      .has_pccard = 1,
-+      .has_ehci0 = 1,
-+
-+      .has_udc0                       = 1,
-+
-+      .leds = {
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = NB4_74HC64_GPIO(4),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "traffic",
-+                      .gpio           = 2,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tel",
-+                      .gpio           = NB4_74HC64_GPIO(3),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tv",
-+                      .gpio           = NB4_74HC64_GPIO(2),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi",
-+                      .gpio           = 15,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "alarm",
-+                      .gpio           = NB4_74HC64_GPIO(0),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:red",
-+                      .gpio           = 29,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:green",
-+                      .gpio           = 30,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:blue",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+      },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 34,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+              {
-+                      .desc           = "wps",
-+                      .gpio           = 37,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_WPS_BUTTON,
-+                      .threshold      = 3,
-+              },
-+      },
-+      .devs = nb4_devices,
-+      .num_devs = ARRAY_SIZE(nb4_devices),
-+      .spis = nb4_spi_devices,
-+      .num_spis = ARRAY_SIZE(nb4_spi_devices),
-+};
-+
-+static struct board_info __initdata board_nb4_ser_r2 = {
-+      .name                           = "NB4-SER-r2",
-+      .expected_cpu_id                = 0x6358,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+
-+      .has_ohci0 = 1,
-+      .has_pccard = 1,
-+      .has_ehci0 = 1,
-+
-+      .leds = {
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = NB4_74HC64_GPIO(4),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "traffic",
-+                      .gpio           = 2,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tel",
-+                      .gpio           = NB4_74HC64_GPIO(3),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tv",
-+                      .gpio           = NB4_74HC64_GPIO(2),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi",
-+                      .gpio           = 15,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "alarm",
-+                      .gpio           = NB4_74HC64_GPIO(0),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:red",
-+                      .gpio           = 29,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:green",
-+                      .gpio           = 30,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:blue",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+      },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 34,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+              {
-+                      .desc           = "wps",
-+                      .gpio           = 37,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_WPS_BUTTON,
-+                      .threshold      = 3,
-+              },
-+      },
-+      .devs = nb4_devices,
-+      .num_devs = ARRAY_SIZE(nb4_devices),
-+      .spis = nb4_spi_devices,
-+      .num_spis = ARRAY_SIZE(nb4_spi_devices),
-+};
-+
-+static struct board_info __initdata board_nb4_fxc_r1 = {
-+      .name                           = "NB4-FXC-r1",
-+      .expected_cpu_id                = 0x6358,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+
-+      .has_ohci0 = 1,
-+      .has_pccard = 1,
-+      .has_ehci0 = 1,
-+
-+      .has_udc0                       = 1,
-+
-+      .leds = {
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = NB4_74HC64_GPIO(4),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "traffic",
-+                      .gpio           = 2,
-+              },
-+              {
-+                      .name           = "tel",
-+                      .gpio           = NB4_74HC64_GPIO(3),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tv",
-+                      .gpio           = NB4_74HC64_GPIO(2),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi",
-+                      .gpio           = 15,
-+              },
-+              {
-+                      .name           = "alarm",
-+                      .gpio           = NB4_74HC64_GPIO(0),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:red",
-+                      .gpio           = 29,
-+              },
-+              {
-+                      .name           = "service:green",
-+                      .gpio           = 30,
-+              },
-+              {
-+                      .name           = "service:blue",
-+                      .gpio           = 4,
-+              },
-+      },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 34,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+              {
-+                      .desc           = "wps",
-+                      .gpio           = 37,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_WPS_BUTTON,
-+                      .threshold      = 3,
-+              },
-+      },
-+      .devs = nb4_devices,
-+      .num_devs = ARRAY_SIZE(nb4_devices),
-+      .spis = nb4_spi_devices,
-+      .num_spis = ARRAY_SIZE(nb4_spi_devices),
-+};
-+
-+static struct board_info __initdata board_nb4_fxc_r2 = {
-+      .name                           = "NB4-FXC-r2",
-+      .expected_cpu_id                = 0x6358,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+
-+      .has_ohci0 = 1,
-+      .has_pccard = 1,
-+      .has_ehci0 = 1,
-+
-+      .leds = {
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = NB4_74HC64_GPIO(4),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "traffic",
-+                      .gpio           = 2,
-+              },
-+              {
-+                      .name           = "tel",
-+                      .gpio           = NB4_74HC64_GPIO(3),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tv",
-+                      .gpio           = NB4_74HC64_GPIO(2),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi",
-+                      .gpio           = 15,
-+              },
-+              {
-+                      .name           = "alarm",
-+                      .gpio           = NB4_74HC64_GPIO(0),
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "service:red",
-+                      .gpio           = 29,
-+              },
-+              {
-+                      .name           = "service:green",
-+                      .gpio           = 30,
-+              },
-+              {
-+                      .name           = "service:blue",
-+                      .gpio           = 4,
-+              },
-+      },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 34,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+              {
-+                      .desc           = "wps",
-+                      .gpio           = 37,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_WPS_BUTTON,
-+                      .threshold      = 3,
-+              },
-+      },
-+      .devs = nb4_devices,
-+      .num_devs = ARRAY_SIZE(nb4_devices),
-+      .spis = nb4_spi_devices,
-+      .num_spis = ARRAY_SIZE(nb4_spi_devices),
-+};
- #endif
- /*
-@@ -810,9 +1315,30 @@ static const struct board_info __initdat
-       &board_96358vw2,
-       &board_AGPFS0,
-       &board_DWVS0,
-+      &board_nb4_ser_r0,
-+      &board_nb4_ser_r1,
-+      &board_nb4_ser_r2,
-+      &board_nb4_fxc_r1,
-+      &board_nb4_fxc_r2,
- #endif
- };
-+static void __init nb4_nvram_fixup(void)
-+{
-+      u8 *boot_addr, *p;
-+      u32 val;
-+
-+      if (BCMCPU_IS_6358() && (!strcmp(nvram.name, "96358VW"))) {
-+              val = bcm_mpi_readl(MPI_CSBASE_REG(0));
-+              val &= MPI_CSBASE_BASE_MASK;
-+              boot_addr = (u8 *)KSEG1ADDR(val);
-+              /* Extract nb4 PID */
-+              p = boot_addr + NB4_PID_OFFSET;
-+              if (!memcmp(p, "NB4-", 4))
-+                      memcpy(nvram.name, p, sizeof("NB4-XXX-rX"));
-+      }
-+}
-+
- /*
-  * Register a sane SPROMv2 to make the on-board
-  * bcm4318 WLAN work
-@@ -959,6 +1485,9 @@ void __init board_prom_init(void)
-               boardid_fixup(boot_addr);
-       }
-+      /* Fixup broken nb4 board name */
-+      nb4_nvram_fixup();
-+
-       /* find board by name */
-       for (i = 0; i < ARRAY_SIZE(bcm963xx_boards); i++) {
-               if (strncmp(nvram.name, bcm963xx_boards[i]->name,
diff --git a/target/linux/brcm63xx/patches-2.6.38/442-board-96338W2_E7T.patch b/target/linux/brcm63xx/patches-2.6.38/442-board-96338W2_E7T.patch
deleted file mode 100644 (file)
index 66ced55..0000000
+++ /dev/null
@@ -1,49 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -146,6 +146,38 @@ static struct board_info __initdata boar
-               },
-       },
- };
-+
-+static struct board_info __initdata board_96338w2_e7t = {
-+      .name                           = "96338W2_E7T",
-+      .expected_cpu_id                = 0x6338,
-+
-+      .has_enet0                      = 1,
-+
-+      .enet0 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+              .leds = {
-+              {
-+                      .name           = "ppp",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "ppp-fail",
-+                      .gpio           = 5,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "power",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+
-+              },
-+      },
-+};
- #endif
- /*
-@@ -1294,6 +1326,7 @@ static const struct board_info __initdat
- #ifdef CONFIG_BCM63XX_CPU_6338
-       &board_96338gw,
-       &board_96338w,
-+      &board_96338w2_e7t,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6345
-       &board_96345gw2,
diff --git a/target/linux/brcm63xx/patches-2.6.38/443-board-CPVA642.patch b/target/linux/brcm63xx/patches-2.6.38/443-board-CPVA642.patch
deleted file mode 100644 (file)
index 0ace02d..0000000
+++ /dev/null
@@ -1,109 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -685,6 +685,98 @@ static struct board_info __initdata boar
-       },
- };
-+static struct board_info __initdata board_CPVA642 = {
-+      .name                           = "CPVA642",
-+      .expected_cpu_id                = 0x6358,
-+
-+      .has_uart0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .has_ohci0 = 1,
-+      .has_ehci0 = 1,
-+
-+      .leds = {
-+          /* bi-color */
-+              {
-+                      .name           = "power:red",
-+                      .gpio           = 14,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "power:green",
-+                      .gpio           = 11,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+              {
-+                      .name           = "wifi:red",
-+                      .gpio           = 6,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi:green",
-+                      .gpio           = 28,
-+                      .active_low     = 0,
-+              },
-+              {
-+                      .name           = "link:red",
-+                      .gpio           = 9,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "link:green",
-+                      .gpio           = 10,
-+                      .active_low     = 1,
-+              },
-+              /* green only */
-+              {
-+                      .name           = "ether",
-+                      .gpio           = 1,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "phone1",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "phone2",
-+                      .gpio           = 2,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "usb",
-+                      .gpio           = 3,
-+                      .active_low     = 1,
-+              },
-+    },
-+
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 36,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+              {
-+                      .desc           = "wps",
-+                      .gpio           = 37,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_WPS_BUTTON,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
-+
- static struct board_info __initdata board_AGPFS0 = {
-       .name                           = "AGPF-S0",
-       .expected_cpu_id                = 0x6358,
-@@ -1347,6 +1439,7 @@ static const struct board_info __initdat
-       &board_96358vw,
-       &board_96358vw2,
-       &board_AGPFS0,
-+      &board_CPVA642,
-       &board_DWVS0,
-       &board_nb4_ser_r0,
-       &board_nb4_ser_r1,
diff --git a/target/linux/brcm63xx/patches-2.6.38/444-board_dsl_274xb_rev_c.patch b/target/linux/brcm63xx/patches-2.6.38/444-board_dsl_274xb_rev_c.patch
deleted file mode 100644 (file)
index 5bafc77..0000000
+++ /dev/null
@@ -1,70 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -914,6 +914,59 @@ static struct board_info __initdata boar
-       .has_ohci0                      = 1,
- };
-+/* D-Link DSL-274xB revison C2/C3 */
-+static struct board_info __initdata board_dsl_274xb_rev_c = {
-+      .name                           = "AW4139",
-+      .expected_cpu_id                = 0x6358,
-+
-+      .has_uart0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .leds = {
-+              {
-+                      .name           = "dsl-274xb:green:power",
-+                      .gpio           = 5,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+              {
-+                      .name           = "dsl-274xb:red:power",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "dsl-274xb:green:adsl",
-+                      .gpio           = 9,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "dsl-274xb:green:internet",
-+                      .gpio           = 2,
-+              },
-+              {
-+                      .name           = "dsl-274xb:red:internet",
-+                      .gpio           = 10,
-+              },
-+      },
-+
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 34,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
- struct spi_gpio_platform_data nb4_spi_gpio_data = {
-       .sck            = NB4_SPI_GPIO_CLK,
-       .mosi           = NB4_SPI_GPIO_MOSI,
-@@ -1441,6 +1494,7 @@ static const struct board_info __initdat
-       &board_AGPFS0,
-       &board_CPVA642,
-       &board_DWVS0,
-+      &board_dsl_274xb_rev_c,
-       &board_nb4_ser_r0,
-       &board_nb4_ser_r1,
-       &board_nb4_ser_r2,
diff --git a/target/linux/brcm63xx/patches-2.6.38/445-board_spw500v.patch b/target/linux/brcm63xx/patches-2.6.38/445-board_spw500v.patch
deleted file mode 100644 (file)
index e2215f2..0000000
+++ /dev/null
@@ -1,78 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -579,6 +579,67 @@ static struct board_info __initdata boar
-       },
- };
-+static struct board_info __initdata board_spw500v = {
-+      .name                           = "SPW500V",
-+      .expected_cpu_id                = 0x6348,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .has_dsp                        = 1,
-+      .dsp = {
-+              .gpio_rst               = 6,
-+              .gpio_int               = 34,
-+              .ext_irq                = 2,
-+              .cs                     = 2,
-+      },
-+
-+      .leds = {
-+              {
-+                      .name           = "power:red",
-+                      .gpio           = 1,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "power:green",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+              {
-+                      .name           = "ppp",
-+                      .gpio           = 3,
-+                      .active_low     = 1,
-+              },
-+              {       .name           = "pstn",
-+                      .gpio           = 28,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "voip",
-+                      .gpio           = 32,
-+                      .active_low     = 1,
-+              },
-+      },
-+
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 33,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
- #endif
- /*
-@@ -1486,6 +1547,7 @@ static const struct board_info __initdat
-       &board_96348gw_a,
-       &board_rta1025w_16,
-       &board_96348_D4PW,
-+      &board_spw500v,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6358
diff --git a/target/linux/brcm63xx/patches-2.6.38/447-board_gw6200_gw6000.patch b/target/linux/brcm63xx/patches-2.6.38/447-board_gw6200_gw6000.patch
deleted file mode 100644 (file)
index c06fda9..0000000
+++ /dev/null
@@ -1,129 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -432,6 +432,117 @@ static struct board_info __initdata boar
-       },
- };
-+static struct board_info __initdata board_gw6200 = {
-+      .name                           = "GW6200",
-+      .expected_cpu_id                = 0x6348,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .has_ohci0 = 1,
-+
-+      .has_dsp                        = 1,
-+              .dsp = {
-+        .gpio_rst             = 8, /* FIXME: What is real GPIO here? */
-+              .gpio_int               = 34,
-+              .ext_irq                = 2,
-+              .cs                     = 2,
-+      },
-+
-+      .leds = {
-+              {
-+                      .name           = "line1",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "line2",
-+                      .gpio           = 5,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "line3",
-+                      .gpio           = 6,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "tel",
-+                      .gpio           = 7,
-+                      .active_low     = 1,
-+              },
-+              {
-+                  .name               = "ethernet",
-+                  .gpio               = 35,
-+                  .active_low = 1,
-+              }, 
-+      },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 36,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
-+static struct board_info __initdata board_gw6000 = {
-+      .name                           = "GW6000",
-+      .expected_cpu_id                = 0x6348,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .has_ohci0 = 1,
-+
-+      .has_dsp                        = 1,
-+      .dsp = {
-+              .gpio_rst               = 6,
-+              .gpio_int               = 34,
-+              .ext_irq                = 2,
-+              .cs                     = 2,
-+      },
-+
-+      /* GW6000 has no GPIO-controlled leds */
-+
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 36,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
-+
-+
- static struct board_info __initdata board_FAST2404 = {
-       .name                           = "F@ST2404",
-       .expected_cpu_id                = 0x6348,
-@@ -1540,6 +1651,8 @@ static const struct board_info __initdat
- #ifdef CONFIG_BCM63XX_CPU_6348
-       &board_96348r,
-       &board_96348gw,
-+      &board_gw6000,
-+      &board_gw6200,
-       &board_96348gw_10,
-       &board_96348gw_11,
-       &board_FAST2404,
diff --git a/target/linux/brcm63xx/patches-2.6.38/448-board-MAGIC.patch b/target/linux/brcm63xx/patches-2.6.38/448-board-MAGIC.patch
deleted file mode 100644 (file)
index 47e7db1..0000000
+++ /dev/null
@@ -1,87 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -751,6 +751,76 @@ static struct board_info __initdata boar
-       },
- };
-+static struct board_info __initdata board_96348sv = {
-+      .name                           = "MAGIC",
-+      .expected_cpu_id        = 0x6348,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                        = 1,
-+              .use_internal_phy       = 1,
-+      },
-+      .enet1 = {
-+              /* is has BP_ENET_EXTERNAL_PHY */
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .has_ohci0                      = 1,
-+      .has_pccard                     = 1,
-+      .has_ehci0                      = 1,
-+
-+      .has_dsp                        = 1,
-+      .dsp = {
-+              .gpio_rst               = 25,
-+              .gpio_int               = 34,
-+              .cs                             = 2,
-+              .ext_irq                = 2,
-+      },
-+
-+      .leds = {
-+              {
-+                      .name           = "voip",
-+                      .gpio           = 22,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = 5,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi",
-+                      .gpio           = 28,
-+              },
-+              {
-+                      .name           = "usb",
-+                      .gpio           = 35,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "hpna",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "power",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+              {
-+                      .name           = "stop",
-+                      .gpio           = 1,
-+                      .active_low     = 1,
-+              },
-+      },
-+};
-+
- #endif
- /*
-@@ -1661,6 +1731,7 @@ static const struct board_info __initdat
-       &board_rta1025w_16,
-       &board_96348_D4PW,
-       &board_spw500v,
-+      &board_96348sv,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6358
diff --git a/target/linux/brcm63xx/patches-2.6.38/449-board_hw553.patch b/target/linux/brcm63xx/patches-2.6.38/449-board_hw553.patch
deleted file mode 100644 (file)
index f806ad0..0000000
+++ /dev/null
@@ -1,90 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -1706,6 +1706,79 @@ static struct board_info __initdata boar
- };
- #endif
-+static struct board_info __initdata board_HW553 = {
-+      .name                           = "HW553",
-+      .expected_cpu_id                = 0x6358,
-+
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .has_ohci0 = 1,
-+      .has_ehci0 = 1,
-+
-+      .leds = {
-+              /*Each led on HW553 is bi-color (except wifi) */                
-+              {
-+                      .name           = "lan:red",
-+                      .gpio           = 34,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "lan:blue",
-+                      .gpio           = 35,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "adsl:red",
-+                      .gpio           = 22,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "adsl:blue",
-+                      .gpio           = 23,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "power:red",
-+                      .gpio           = 5,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+
-+              {
-+                      .name           = "power:blue",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wifi:red",
-+                      .gpio           = 25,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "internetkey:red",
-+                      .gpio           = 12,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "internetkey:blue",
-+                      .gpio           = 13,
-+                      .active_low     = 1,
-+              },
-+      },
-+};
-+
- /*
-  * all boards
-  */
-@@ -1746,6 +1819,7 @@ static const struct board_info __initdat
-       &board_nb4_ser_r2,
-       &board_nb4_fxc_r1,
-       &board_nb4_fxc_r2,
-+      &board_HW553,
- #endif
- };
diff --git a/target/linux/brcm63xx/patches-2.6.38/450-board_rta1320_16m.patch b/target/linux/brcm63xx/patches-2.6.38/450-board_rta1320_16m.patch
deleted file mode 100644 (file)
index 537a88b..0000000
+++ /dev/null
@@ -1,54 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -178,6 +178,43 @@ static struct board_info __initdata boar
-               },
-       },
- };
-+
-+static struct board_info __initdata board_rta1320_16m = {
-+      .name                           = "RTA1320_16M",
-+      .expected_cpu_id                = 0x6338,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+
-+      .enet0 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+              .leds = {
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = 3,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "ppp",
-+                      .gpio           = 4,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "power",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+              {
-+                      .name           = "stop",
-+                      .gpio           = 1,
-+                      .active_low     = 1,
-+              },
-+      },
-+};
- #endif
- /*
-@@ -1787,6 +1824,7 @@ static const struct board_info __initdat
-       &board_96338gw,
-       &board_96338w,
-       &board_96338w2_e7t,
-+      &board_rta1320_16m,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6345
-       &board_96345gw2,
diff --git a/target/linux/brcm63xx/patches-2.6.38/451-board_spw303v.patch b/target/linux/brcm63xx/patches-2.6.38/451-board_spw303v.patch
deleted file mode 100644 (file)
index 25b7140..0000000
+++ /dev/null
@@ -1,83 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -1741,6 +1741,72 @@ static struct board_info __initdata boar
-       .spis = nb4_spi_devices,
-       .num_spis = ARRAY_SIZE(nb4_spi_devices),
- };
-+
-+ /* T-Home Speedport W 303V Typ B */
-+static struct board_info __initdata board_spw303v = {
-+      .name                   = "96358-502V",
-+      .expected_cpu_id        = 0x6358,
-+
-+      .has_uart0              = 1,
-+      .has_enet0              = 1,
-+      .has_pci                = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .leds = {
-+              {
-+                      .name           = "spw303v:green:power+adsl",
-+                      .gpio           = 22,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "spw303v:red:power+adsl",
-+                      .gpio           = 2,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "spw303v:green:ppp",
-+                      .gpio           = 5,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "spw303v:green:ses",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "spw303v:green:voip",
-+                      .gpio           = 27,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "spw303v:green:pots",
-+                      .gpio           = 31,
-+                      .active_low     = 1,
-+              },
-+      },
-+
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 11,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+              {
-+                      .desc           = "ses",
-+                      .gpio           = 37,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_WPS_BUTTON,
-+                      .threshold      = 3,
-+              },
-+      }
-+};
- #endif
- static struct board_info __initdata board_HW553 = {
-@@ -1858,6 +1924,7 @@ static const struct board_info __initdat
-       &board_nb4_fxc_r1,
-       &board_nb4_fxc_r2,
-       &board_HW553,
-+      &board_spw303v,
- #endif
- };
diff --git a/target/linux/brcm63xx/patches-2.6.38/452-board_V2500V.patch b/target/linux/brcm63xx/patches-2.6.38/452-board_V2500V.patch
deleted file mode 100644 (file)
index 4b483d4..0000000
+++ /dev/null
@@ -1,112 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -858,6 +858,63 @@ static struct board_info __initdata boar
-       },
- };
-+      static struct board_info __initdata board_V2500V_BB = {
-+        .name                           = "V2500V_BB",
-+        .expected_cpu_id                = 0x6348,
-+
-+        .has_uart0                      = 1,
-+        .has_enet0                      = 1,
-+        .has_enet1                      = 1,
-+        .has_pci                        = 1,
-+
-+        .enet0 = {
-+                .has_phy                = 1,
-+                .use_internal_phy       = 1,
-+        },
-+        .enet1 = {
-+                .force_speed_100        = 1,
-+                .force_duplex_full      = 1,
-+        },
-+
-+      .leds = {
-+              {
-+                      .name           = "power:green",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+              {
-+                      .name           = "power:red",
-+                      .gpio           = 1,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = 2,
-+                      .active_low     = 1,
-+              },
-+              {       .name           = "ppp",
-+                      .gpio           = 3,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wireless",
-+                      .gpio           = 6,
-+                      .active_low     = 1,
-+              },
-+      },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 31,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
- #endif
- /*
-@@ -1909,6 +1966,7 @@ static const struct board_info __initdat
-       &board_96348_D4PW,
-       &board_spw500v,
-       &board_96348sv,
-+      &board_V2500V_BB,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6358
-@@ -2057,6 +2115,22 @@ void __init board_prom_init(void)
-               val &= MPI_CSBASE_BASE_MASK;
-       }
-       boot_addr = (u8 *)KSEG1ADDR(val);
-+      printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr);
-+
-+      /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
-+      /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
-+      /* Loading firmware from the CFE Prompt always loads to Bank 0 */
-+      /* Do an early check of CFE and then select bank 0 */
-+
-+              if (boot_addr == (u8 *)0xbf800000) {
-+              u8 *tmp_boot_addr;
-+              tmp_boot_addr = (u8 *)0xbfc00000; // Address of Bank 0
-+              memcpy(&nvram, tmp_boot_addr + BCM963XX_NVRAM_OFFSET, sizeof(nvram));
-+              if (!strcmp(nvram.name, "V2500V_BB")) {
-+                      printk(KERN_INFO PFX "V2500V: nvram bank 0\n");
-+                      boot_addr = (u8 *)0xbfc00000; // Bank 0
-+              }
-+      }
-       /* dump cfe version */
-       cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
-@@ -2264,6 +2338,14 @@ int __init board_register_devices(void)
-               val = bcm_mpi_readl(MPI_CSBASE_REG(0));
-               val &= MPI_CSBASE_BASE_MASK;
-       }
-+
-+      /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
-+      /* Loading from CFE always uses Bank 0 */
-+      if (!strcmp(board.name, "V2500V_BB")) {
-+              printk(KERN_INFO PFX "V2500V: Start in Bank 0\n");
-+              val = val + 0x400000; // Select Bank 0 start address
-+              }
-+
-       mtd_resources[0].start = val;
-       mtd_resources[0].end = 0x1FFFFFFF;
diff --git a/target/linux/brcm63xx/patches-2.6.38/453-board_BTV2110.patch b/target/linux/brcm63xx/patches-2.6.38/453-board_BTV2110.patch
deleted file mode 100644 (file)
index 9e280b4..0000000
+++ /dev/null
@@ -1,73 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -401,6 +401,62 @@ static struct board_info __initdata boar
-       },
- };
-+
-+/* BT Voyager 2110 */
-+static struct board_info __initdata board_V2110 = {
-+      .name                           = "V2110",
-+      .expected_cpu_id                = 0x6348,
-+
-+      .has_uart0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .leds = {
-+              {
-+                      .name           = "V2110:green:power",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+              {
-+                      .name           = "V2110:red:power",
-+                      .gpio           = 1,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "V2110:green:adsl",
-+                      .gpio           = 2,
-+                      .active_low     = 1,
-+              },
-+              {       .name           = "V2110:green:ppp",
-+                      .gpio           = 3,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "V2110:green:wireless",
-+                      .gpio           = 6,
-+                      .active_low     = 1,
-+              },
-+      },
-+
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 33,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
-+
- static struct board_info __initdata board_96348gw = {
-       .name                           = "96348GW",
-       .expected_cpu_id                = 0x6348,
-@@ -1967,6 +2023,7 @@ static const struct board_info __initdat
-       &board_spw500v,
-       &board_96348sv,
-       &board_V2500V_BB,
-+      &board_V2110,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6358
diff --git a/target/linux/brcm63xx/patches-2.6.38/454-board_livebox.patch b/target/linux/brcm63xx/patches-2.6.38/454-board_livebox.patch
deleted file mode 100644 (file)
index 6c39045..0000000
+++ /dev/null
@@ -1,251 +0,0 @@
---- a/arch/mips/bcm63xx/boards/Kconfig
-+++ b/arch/mips/bcm63xx/boards/Kconfig
-@@ -8,4 +8,10 @@ config BOARD_BCM963XX
-       select SSB
-        help
-+config BOARD_LIVEBOX
-+      bool "Inventel Livebox(es) boards"
-+      select SSB
-+      help
-+       Inventel Livebox boards using the RedBoot bootloader.
-+
- endchoice
---- a/arch/mips/bcm63xx/boards/Makefile
-+++ b/arch/mips/bcm63xx/boards/Makefile
-@@ -1,3 +1,4 @@
- obj-$(CONFIG_BOARD_BCM963XX)          += board_bcm963xx.o
-+obj-$(CONFIG_BOARD_LIVEBOX)           += board_livebox.o
- EXTRA_CFLAGS += -Werror
---- /dev/null
-+++ b/arch/mips/bcm63xx/boards/board_livebox.c
-@@ -0,0 +1,228 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License.  See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2008 Florian Fainelli <florian@openwrt.org>
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/kernel.h>
-+#include <linux/string.h>
-+#include <linux/platform_device.h>
-+#include <linux/mtd/mtd.h>
-+#include <linux/mtd/partitions.h>
-+#include <linux/mtd/physmap.h>
-+#include <linux/input.h>
-+#include <linux/gpio_buttons.h>
-+#include <asm/addrspace.h>
-+#include <bcm63xx_board.h>
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_regs.h>
-+#include <bcm63xx_io.h>
-+#include <bcm63xx_dev_uart.h>
-+#include <bcm63xx_dev_pci.h>
-+#include <bcm63xx_dev_enet.h>
-+#include <bcm63xx_dev_pcmcia.h>
-+#include <bcm63xx_dev_usb_ohci.h>
-+#include <bcm63xx_dev_usb_ehci.h>
-+#include <board_bcm963xx.h>
-+
-+#define PFX   "board_livebox: "
-+
-+static unsigned int mac_addr_used = 0;
-+static struct board_info board;
-+
-+/*
-+ * known 6348 boards
-+ */
-+#ifdef CONFIG_BCM63XX_CPU_6348
-+static struct board_info __initdata board_livebox = {
-+      .name                           = "Livebox",
-+      .expected_cpu_id                = 0x6348,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 1,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet0 = {
-+              .has_phy                = 1,
-+              .use_internal_phy       = 1,
-+      },
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .has_ohci0                      = 1,
-+      .has_pccard                     = 1,
-+      .has_ehci0                      = 1,
-+};
-+#endif
-+
-+/*
-+ * all boards
-+ */
-+static const struct board_info __initdata *bcm963xx_boards[] = {
-+#ifdef CONFIG_BCM63XX_CPU_6348
-+      &board_livebox
-+#endif
-+};
-+
-+/*
-+ * early init callback
-+ */
-+void __init board_prom_init(void)
-+{
-+      u32 val;
-+
-+      /* read base address of boot chip select (0) */
-+      val = bcm_mpi_readl(MPI_CSBASE_REG(0));
-+      val &= MPI_CSBASE_BASE_MASK;
-+
-+      /* assume board is a Livebox */
-+      memcpy(&board, bcm963xx_boards[0], sizeof(board));
-+
-+      /* setup pin multiplexing depending on board enabled device,
-+       * this has to be done this early since PCI init is done
-+       * inside arch_initcall */
-+      val = 0;
-+
-+      if (board.has_pci) {
-+              bcm63xx_pci_enabled = 1;
-+              if (BCMCPU_IS_6348())
-+                      val |= GPIO_MODE_6348_G2_PCI;
-+      }
-+
-+      if (board.has_pccard) {
-+              if (BCMCPU_IS_6348())
-+                      val |= GPIO_MODE_6348_G1_MII_PCCARD;
-+      }
-+
-+      if (board.has_enet0 && !board.enet0.use_internal_phy) {
-+              if (BCMCPU_IS_6348())
-+                      val |= GPIO_MODE_6348_G3_EXT_MII |
-+                              GPIO_MODE_6348_G0_EXT_MII;
-+      }
-+
-+      if (board.has_enet1 && !board.enet1.use_internal_phy) {
-+              if (BCMCPU_IS_6348())
-+                      val |= GPIO_MODE_6348_G3_EXT_MII |
-+                              GPIO_MODE_6348_G0_EXT_MII;
-+      }
-+
-+      bcm_gpio_writel(val, GPIO_MODE_REG);
-+}
-+
-+/*
-+ * second stage init callback, good time to panic if we couldn't
-+ * identify on which board we're running since early printk is working
-+ */
-+void __init board_setup(void)
-+{
-+      if (!board.name[0])
-+              panic("unable to detect bcm963xx board");
-+      printk(KERN_INFO PFX "board name: %s\n", board.name);
-+
-+      /* make sure we're running on expected cpu */
-+      if (bcm63xx_get_cpu_id() != board.expected_cpu_id)
-+              panic("unexpected CPU for bcm963xx board");
-+}
-+
-+/*
-+ * return board name for /proc/cpuinfo
-+ */
-+const char *board_get_name(void)
-+{
-+      return board.name;
-+}
-+
-+/*
-+ * register & return a new board mac address
-+ */
-+
-+static int board_get_mac_address(u8 *mac)
-+{
-+      u8 default_mac[ETH_ALEN] = {0x00, 0x07, 0x3A, 0x00, 0x00, 0x00};
-+      u8 *p;
-+      int count;
-+
-+      memcpy(mac, default_mac, ETH_ALEN);
-+
-+      p = mac + ETH_ALEN - 1;
-+      count = mac_addr_used;
-+
-+      while (count--) {
-+              do {
-+                      (*p)++;
-+                      if (*p != 0)
-+                              break;
-+                      p--;
-+              } while (p != mac);
-+      }
-+
-+      if (p == mac) {
-+              printk(KERN_ERR PFX "unable to fetch mac address\n");
-+              return -ENODEV;
-+      }
-+        mac_addr_used++;
-+
-+      return 0;
-+}
-+
-+static struct resource mtd_resources[] = {
-+      {
-+              .start          = 0,    /* filled at runtime */
-+              .end            = 0,    /* filled at runtime */
-+              .flags          = IORESOURCE_MEM,
-+      }
-+};
-+
-+static struct platform_device mtd_dev = {
-+      .name                   = "bcm963xx-flash",
-+      .resource               = mtd_resources,
-+      .num_resources          = ARRAY_SIZE(mtd_resources),
-+};
-+
-+
-+/*
-+ * third stage init callback, register all board devices.
-+ */
-+int __init board_register_devices(void)
-+{
-+      u32 val;
-+
-+      if (board.has_uart0)
-+              bcm63xx_uart_register(0);
-+
-+      if (board.has_pccard)
-+              bcm63xx_pcmcia_register();
-+
-+      if (board.has_enet0 &&
-+          !board_get_mac_address(board.enet0.mac_addr))
-+              bcm63xx_enet_register(0, &board.enet0);
-+
-+      if (board.has_enet1 &&
-+          !board_get_mac_address(board.enet1.mac_addr))
-+              bcm63xx_enet_register(1, &board.enet1);
-+
-+      if (board.has_ohci0)
-+              bcm63xx_ohci_register();
-+
-+      if (board.has_ehci0)
-+              bcm63xx_ehci_register();
-+
-+
-+      /* read base address of boot chip select (0) */
-+      val = bcm_mpi_readl(MPI_CSBASE_REG(0));
-+      val &= MPI_CSBASE_BASE_MASK;
-+      mtd_resources[0].start = val;
-+      mtd_resources[0].end = 0x1FFFFFFF;
-+
-+      platform_device_register(&mtd_dev);
-+
-+      return 0;
-+}
-+
diff --git a/target/linux/brcm63xx/patches-2.6.38/455-board_ct536_ct5621.patch b/target/linux/brcm63xx/patches-2.6.38/455-board_ct536_ct5621.patch
deleted file mode 100644 (file)
index 1af07ae..0000000
+++ /dev/null
@@ -1,60 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -457,6 +457,49 @@ static struct board_info __initdata boar
- };
-+static struct board_info __initdata board_ct536_ct5621 = {
-+      .name                           = "CT536_CT5621",
-+      .expected_cpu_id                = 0x6348,
-+
-+      .has_uart0                      = 1,
-+      .has_enet0                      = 0,
-+      .has_enet1                      = 1,
-+      .has_pci                        = 1,
-+
-+      .enet1 = {
-+              .force_speed_100        = 1,
-+              .force_duplex_full      = 1,
-+      },
-+
-+      .has_ohci0 = 1,
-+      .has_pccard = 1,
-+      .has_ehci0 = 1,
-+
-+      .leds = {
-+              {
-+                      .name           = "adsl-fail",
-+                      .gpio           = 2,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "power",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+      },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 33,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
- static struct board_info __initdata board_96348gw = {
-       .name                           = "96348GW",
-       .expected_cpu_id                = 0x6348,
-@@ -2024,6 +2067,7 @@ static const struct board_info __initdat
-       &board_96348sv,
-       &board_V2500V_BB,
-       &board_V2110,
-+      &board_ct536_ct5621,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6358
diff --git a/target/linux/brcm63xx/patches-2.6.38/500-ssb-add-callback-for-sprom.patch b/target/linux/brcm63xx/patches-2.6.38/500-ssb-add-callback-for-sprom.patch
deleted file mode 100644 (file)
index 349e5f5..0000000
+++ /dev/null
@@ -1,143 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -2128,6 +2128,17 @@ static struct ssb_sprom bcm63xx_sprom =
-       .boardflags_lo          = 0x2848,
-       .boardflags_hi          = 0x0000,
- };
-+
-+int bcm63xx_get_fallback_sprom(struct ssb_bus *bus, struct ssb_sprom *out)
-+{
-+      if (bus->bustype == SSB_BUSTYPE_PCI) {
-+              memcpy(out, &bcm63xx_sprom, sizeof(struct ssb_sprom));
-+              return 0;
-+      } else {
-+              printk(KERN_ERR PFX "unable to fill SPROM for given bustype.\n");
-+              return -EINVAL;
-+      }
-+}
- #endif
- /*
-@@ -2328,8 +2339,9 @@ void __init board_prom_init(void)
-       if (!board_get_mac_address(bcm63xx_sprom.il0mac)) {
-               memcpy(bcm63xx_sprom.et0mac, bcm63xx_sprom.il0mac, ETH_ALEN);
-               memcpy(bcm63xx_sprom.et1mac, bcm63xx_sprom.il0mac, ETH_ALEN);
--              if (ssb_arch_set_fallback_sprom(&bcm63xx_sprom) < 0)
--                      printk(KERN_ERR "failed to register fallback SPROM\n");
-+              if (ssb_arch_register_fallback_sprom(
-+                              &bcm63xx_get_fallback_sprom) < 0)
-+                      printk(KERN_ERR PFX "failed to register fallback SPROM\n");
-       }
- #endif
- }
---- a/drivers/ssb/pci.c
-+++ b/drivers/ssb/pci.c
-@@ -662,7 +662,6 @@ static int sprom_extract(struct ssb_bus
- static int ssb_pci_sprom_get(struct ssb_bus *bus,
-                            struct ssb_sprom *sprom)
- {
--      const struct ssb_sprom *fallback;
-       int err;
-       u16 *buf;
-@@ -707,10 +706,14 @@ static int ssb_pci_sprom_get(struct ssb_
-               if (err) {
-                       /* All CRC attempts failed.
-                        * Maybe there is no SPROM on the device?
--                       * If we have a fallback, use that. */
--                      fallback = ssb_get_fallback_sprom();
--                      if (fallback) {
--                              memcpy(sprom, fallback, sizeof(*sprom));
-+                       * Now we ask the arch code if there is some sprom
-+                       * avaliable for this device in some other storage */
-+                      err = ssb_fill_sprom_with_fallback(bus, sprom);
-+                      if (err) {
-+                              ssb_printk(KERN_WARNING PFX "WARNING: Using"
-+                                         " fallback SPROM failed (err %d)\n",
-+                                         err);
-+                      } else {
-                               err = 0;
-                               goto out_free;
-                       }
---- a/drivers/ssb/sprom.c
-+++ b/drivers/ssb/sprom.c
-@@ -17,7 +17,7 @@
- #include <linux/slab.h>
--static const struct ssb_sprom *fallback_sprom;
-+static int(*get_fallback_sprom)(struct ssb_bus *dev, struct ssb_sprom *out);
- static int sprom2hex(const u16 *sprom, char *buf, size_t buf_len,
-@@ -145,13 +145,14 @@ out:
- }
- /**
-- * ssb_arch_set_fallback_sprom - Set a fallback SPROM for use if no SPROM is found.
-+ * ssb_arch_register_fallback_sprom - Registers a method providing a fallback
-+ * SPROM if no SPROM is found.
-  *
-- * @sprom: The SPROM data structure to register.
-+ * @sprom_callback: The callbcak function.
-  *
-- * With this function the architecture implementation may register a fallback
-- * SPROM data structure. The fallback is only used for PCI based SSB devices,
-- * where no valid SPROM can be found in the shadow registers.
-+ * With this function the architecture implementation may register a callback
-+ * handler which wills the SPROM data structure. The fallback is only used for
-+ * PCI based SSB devices, where no valid SPROM can be found in the shadow registers.
-  *
-  * This function is useful for weird architectures that have a half-assed SSB device
-  * hardwired to their PCI bus.
-@@ -163,18 +164,21 @@ out:
-  *
-  * This function is available for architecture code, only. So it is not exported.
-  */
--int ssb_arch_set_fallback_sprom(const struct ssb_sprom *sprom)
-+int ssb_arch_register_fallback_sprom(int (*sprom_callback)(struct ssb_bus *bus, struct ssb_sprom *out))
- {
--      if (fallback_sprom)
-+      if (get_fallback_sprom)
-               return -EEXIST;
--      fallback_sprom = sprom;
-+      get_fallback_sprom = sprom_callback;
-       return 0;
- }
--const struct ssb_sprom *ssb_get_fallback_sprom(void)
-+int ssb_fill_sprom_with_fallback(struct ssb_bus *bus, struct ssb_sprom *out)
- {
--      return fallback_sprom;
-+      if (!get_fallback_sprom)
-+              return -ENOENT;
-+
-+      return get_fallback_sprom(bus, out);
- }
- /* http://bcm-v4.sipsolutions.net/802.11/IsSpromAvailable */
---- a/drivers/ssb/ssb_private.h
-+++ b/drivers/ssb/ssb_private.h
-@@ -171,7 +171,7 @@ ssize_t ssb_attr_sprom_store(struct ssb_
-                            const char *buf, size_t count,
-                            int (*sprom_check_crc)(const u16 *sprom, size_t size),
-                            int (*sprom_write)(struct ssb_bus *bus, const u16 *sprom));
--extern const struct ssb_sprom *ssb_get_fallback_sprom(void);
-+extern int ssb_fill_sprom_with_fallback(struct ssb_bus *bus, struct ssb_sprom *out);
- /* core.c */
---- a/include/linux/ssb/ssb.h
-+++ b/include/linux/ssb/ssb.h
-@@ -404,7 +404,9 @@ extern bool ssb_is_sprom_available(struc
- /* Set a fallback SPROM.
-  * See kdoc at the function definition for complete documentation. */
--extern int ssb_arch_set_fallback_sprom(const struct ssb_sprom *sprom);
-+extern int ssb_arch_register_fallback_sprom(
-+              int (*sprom_callback)(struct ssb_bus *bus,
-+              struct ssb_sprom *out));
- /* Suspend a SSB bus.
-  * Call this from the parent bus suspend routine. */
diff --git a/target/linux/brcm63xx/patches-2.6.38/977-ssb_export_fallback_sprom.patch b/target/linux/brcm63xx/patches-2.6.38/977-ssb_export_fallback_sprom.patch
deleted file mode 100644 (file)
index 478019d..0000000
+++ /dev/null
@@ -1,19 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -2108,7 +2108,7 @@ static void __init nb4_nvram_fixup(void)
-  * bcm4318 WLAN work
-  */
- #ifdef CONFIG_SSB_PCIHOST
--static struct ssb_sprom bcm63xx_sprom = {
-+struct ssb_sprom bcm63xx_sprom = {
-       .revision               = 0x02,
-       .board_rev              = 0x17,
-       .country_code           = 0x0,
-@@ -2128,6 +2128,7 @@ static struct ssb_sprom bcm63xx_sprom =
-       .boardflags_lo          = 0x2848,
-       .boardflags_hi          = 0x0000,
- };
-+EXPORT_SYMBOL(bcm63xx_sprom);
- int bcm63xx_get_fallback_sprom(struct ssb_bus *bus, struct ssb_sprom *out)
- {