From: Rafał Miłecki <zajec5@gmail.com>
Date: Tue, 7 Apr 2015 22:06:17 +0000 (+0000)
Subject: kernel: backport ssb patches up to changes queued for 4.1
X-Git-Url: http://git.openwrt.org/?p=openwrt%2Fsvn-archive%2Farchive.git;a=commitdiff_plain;hb=ec37afa619d3ef903539c1eff43cf1c7b7f2636c

kernel: backport ssb patches up to changes queued for 4.1

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45306
---

diff --git a/target/linux/generic/patches-3.18/020-ssb_update.patch b/target/linux/generic/patches-3.18/020-ssb_update.patch
index 9171b24704..7afba07763 100644
--- a/target/linux/generic/patches-3.18/020-ssb_update.patch
+++ b/target/linux/generic/patches-3.18/020-ssb_update.patch
@@ -76,3 +76,58 @@
  
  	return pci_register_driver(driver);
  }
+--- a/drivers/ssb/driver_pcicore.c
++++ b/drivers/ssb/driver_pcicore.c
+@@ -357,6 +357,15 @@ static void ssb_pcicore_init_hostmode(st
+ 	pcicore_write32(pc, SSB_PCICORE_SBTOPCI2,
+ 			SSB_PCICORE_SBTOPCI_MEM | SSB_PCI_DMA);
+ 
++	/*
++	 * Accessing PCI config without a proper delay after devices reset (not
++	 * GPIO reset) was causing reboots on WRT300N v1.0.
++	 * Tested delay 850 us lowered reboot chance to 50-80%, 1000 us fixed it
++	 * completely. Flushing all writes was also tested but with no luck.
++	 */
++	if (pc->dev->bus->chip_id == 0x4704)
++		usleep_range(1000, 2000);
++
+ 	/* Enable PCI bridge BAR0 prefetch and burst */
+ 	val = PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ 	ssb_extpci_write_config(pc, 0, 0, 0, PCI_COMMAND, &val, 2);
+--- a/drivers/ssb/main.c
++++ b/drivers/ssb/main.c
+@@ -90,25 +90,6 @@ found:
+ }
+ #endif /* CONFIG_SSB_PCMCIAHOST */
+ 
+-#ifdef CONFIG_SSB_SDIOHOST
+-struct ssb_bus *ssb_sdio_func_to_bus(struct sdio_func *func)
+-{
+-	struct ssb_bus *bus;
+-
+-	ssb_buses_lock();
+-	list_for_each_entry(bus, &buses, list) {
+-		if (bus->bustype == SSB_BUSTYPE_SDIO &&
+-		    bus->host_sdio == func)
+-			goto found;
+-	}
+-	bus = NULL;
+-found:
+-	ssb_buses_unlock();
+-
+-	return bus;
+-}
+-#endif /* CONFIG_SSB_SDIOHOST */
+-
+ int ssb_for_each_bus_call(unsigned long data,
+ 			  int (*func)(struct ssb_bus *bus, unsigned long data))
+ {
+@@ -1154,6 +1135,8 @@ static u32 ssb_tmslow_reject_bitmask(str
+ 	case SSB_IDLOW_SSBREV_25:     /* TODO - find the proper REJECT bit */
+ 	case SSB_IDLOW_SSBREV_27:     /* same here */
+ 		return SSB_TMSLOW_REJECT;	/* this is a guess */
++	case SSB_IDLOW_SSBREV:
++		break;
+ 	default:
+ 		WARN(1, KERN_INFO "ssb: Backplane Revision 0x%.8X\n", rev);
+ 	}
diff --git a/target/linux/generic/patches-4.0/020-ssb_update.patch b/target/linux/generic/patches-4.0/020-ssb_update.patch
new file mode 100644
index 0000000000..946cb3b106
--- /dev/null
+++ b/target/linux/generic/patches-4.0/020-ssb_update.patch
@@ -0,0 +1,29 @@
+--- a/drivers/ssb/driver_pcicore.c
++++ b/drivers/ssb/driver_pcicore.c
+@@ -357,6 +357,15 @@ static void ssb_pcicore_init_hostmode(st
+ 	pcicore_write32(pc, SSB_PCICORE_SBTOPCI2,
+ 			SSB_PCICORE_SBTOPCI_MEM | SSB_PCI_DMA);
+ 
++	/*
++	 * Accessing PCI config without a proper delay after devices reset (not
++	 * GPIO reset) was causing reboots on WRT300N v1.0.
++	 * Tested delay 850 us lowered reboot chance to 50-80%, 1000 us fixed it
++	 * completely. Flushing all writes was also tested but with no luck.
++	 */
++	if (pc->dev->bus->chip_id == 0x4704)
++		usleep_range(1000, 2000);
++
+ 	/* Enable PCI bridge BAR0 prefetch and burst */
+ 	val = PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ 	ssb_extpci_write_config(pc, 0, 0, 0, PCI_COMMAND, &val, 2);
+--- a/drivers/ssb/main.c
++++ b/drivers/ssb/main.c
+@@ -1135,6 +1135,8 @@ static u32 ssb_tmslow_reject_bitmask(str
+ 	case SSB_IDLOW_SSBREV_25:     /* TODO - find the proper REJECT bit */
+ 	case SSB_IDLOW_SSBREV_27:     /* same here */
+ 		return SSB_TMSLOW_REJECT;	/* this is a guess */
++	case SSB_IDLOW_SSBREV:
++		break;
+ 	default:
+ 		WARN(1, KERN_INFO "ssb: Backplane Revision 0x%.8X\n", rev);
+ 	}