openwrt/svn-archive/archive.git
6 years agobroadcom-diag: add GPIO configuration for Linksys E2000 V1
Hauke Mehrtens [Mon, 16 Sep 2013 19:52:23 +0000 (19:52 +0000)]
broadcom-diag: add GPIO configuration for Linksys E2000 V1

Thank you Javier Achirica for the patch.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38008

6 years agobroadcom-diag: Add WRT310N v1 gpio leds and buttons
Hauke Mehrtens [Mon, 16 Sep 2013 19:50:14 +0000 (19:50 +0000)]
broadcom-diag: Add WRT310N v1 gpio leds and buttons

Signed-off-by: Flavio Silveira <fggs@terra.com.br>
SVN-Revision: 38007

6 years agobrcm47xx: detect Linksys E1200 V2
Hauke Mehrtens [Mon, 16 Sep 2013 19:49:02 +0000 (19:49 +0000)]
brcm47xx: detect Linksys E1200 V2

This adds detection for Linksys E1200 V2

Thank you Lightsword and Rafał.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38006

6 years agobrcm47xx: mtd: bcm47xxpart: detect "factory" partition
Hauke Mehrtens [Mon, 16 Sep 2013 19:47:30 +0000 (19:47 +0000)]
brcm47xx: mtd: bcm47xxpart: detect "factory" partition

A new type of partition with magic FCTY was found on Huawei E970:
46 43 54 59 4b 51 37 4e  41 42 31 38 41 32 39 30  |FCTYKQ7NAB18A290|

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 38005

6 years agobrcm47xx: bgmac: implement unaligned addressing for DMA rings that support it
Hauke Mehrtens [Mon, 16 Sep 2013 19:46:34 +0000 (19:46 +0000)]
brcm47xx: bgmac: implement unaligned addressing for DMA rings that support it

This is important patch for new devices that support unaligned
addressing. That devices suffer from the backward-compatibility bug in
DMA engine. In theory we should be able to use old mechanism, but in
practice DMA address seems to be randomly copied into status register
when hardware reaches end of a ring. This breaks reading slot number
from status register and we can't use DMA anymore.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 38004

6 years agokernel/3.10: add new Kconfig option for firmware partition split
Gabor Juhos [Sun, 15 Sep 2013 17:03:29 +0000 (17:03 +0000)]
kernel/3.10: add new Kconfig option for firmware partition split

Add a new kernel config option for generic firmware partition
split support and change the uImage split support to depend on
the new option. Aslo rename the MTD_UIMAGE_SPLIT_NAME option to
MTD_SPLIT_FIRMWARE_NAME to make it more generic.

The patch is in preparation for multiple firmware format
support.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38002

6 years agobrcm47xx: add detection code for Huawei E970
Hauke Mehrtens [Sun, 15 Sep 2013 17:00:45 +0000 (17:00 +0000)]
brcm47xx: add detection code for Huawei E970

This is based on a patch by Mathias Adam.

Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38001

6 years agokernel: update 3.10 to 3.10.12
Gabor Juhos [Sun, 15 Sep 2013 16:00:41 +0000 (16:00 +0000)]
kernel: update 3.10 to 3.10.12

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38000

6 years agobrcm47xx: bgmac: allow bigger et_swtype nvram variable
Hauke Mehrtens [Sun, 15 Sep 2013 15:50:41 +0000 (15:50 +0000)]
brcm47xx: bgmac: allow bigger et_swtype nvram variable

Without this patch it is impossible to read et_swtype, because the 1
byte space is needed for the terminating null byte. Now it should be
possible to read decimal and hex vars of max 8 bit.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37999

6 years agobrcm47xx: mtd: bcm47xxpart: detect block aligned Squashfs partition
Hauke Mehrtens [Sun, 15 Sep 2013 15:47:45 +0000 (15:47 +0000)]
brcm47xx: mtd: bcm47xxpart: detect block aligned Squashfs partition

Most of the bcm47xx devices use TRX format for storing kernel and some
partition like Squashfs or JFFS2. This is pretty flexible solution, CFE
(the bootloader) just writes (and later boots) TRX at some hardcoded
place and paritions can vary in the size.

However some devices don't use TRX format. Very recently we have
discovered ZTE H218N that has kernel and rootfs partitions at some
"random" places.

This patch allows Linux find a rootfs partition after installing custom
image with a CFE bootloader.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 37998

6 years agokernel/3.10: move OpenWrt MTD options into a submenu
Gabor Juhos [Sun, 15 Sep 2013 15:16:16 +0000 (15:16 +0000)]
kernel/3.10: move OpenWrt MTD options into a submenu

Separate OpenWrt specific MTD options from the mainline
option by moving those into a new submenu in the kernel
configuration interface.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37997

6 years agobrcm47xx: update board detection patch
Hauke Mehrtens [Sun, 15 Sep 2013 15:08:29 +0000 (15:08 +0000)]
brcm47xx: update board detection patch

* Use different structs depending on the number of nvram variables to check.
* Add detection of ZTE H218N, this closes #14151.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37996

6 years agokernel: b53: detect revision of BCM5325
Hauke Mehrtens [Sun, 15 Sep 2013 13:30:49 +0000 (13:30 +0000)]
kernel: b53: detect revision of BCM5325

The revision is stored in a different register than it is in other
Broadcom switches.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37995

6 years agokernel: b53: fix vlan write for BCM5325 revison 3+
Hauke Mehrtens [Sun, 15 Sep 2013 13:29:14 +0000 (13:29 +0000)]
kernel: b53: fix vlan write for BCM5325 revison 3+

These switches are integrated in some recent BCM53XX and BCM47XX SoCs
like the BCM53572.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37994

6 years agobrcm47xx: bgmac: fix internal switch initialization
Hauke Mehrtens [Sun, 15 Sep 2013 09:39:19 +0000 (09:39 +0000)]
brcm47xx: bgmac: fix internal switch initialization

Some devices (BCM4749, BCM5357, BCM53572) have internal switch that
requires initialization. We already have code for this, but because
of the typo in code it was never working. This resulted in network not
working for some routers and possibility of soft-bricking them.

Use correct bit for switch initialization and fix typo in the define.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 37993

6 years agohostapd: adjust the md5sum for the uploaded source tarball (fixes #14155)
Felix Fietkau [Sat, 14 Sep 2013 20:07:35 +0000 (20:07 +0000)]
hostapd: adjust the md5sum for the uploaded source tarball (fixes #14155)

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37990

6 years agobrcm47xx: detect Asus RT-N10
Hauke Mehrtens [Sat, 14 Sep 2013 16:19:21 +0000 (16:19 +0000)]
brcm47xx: detect Asus RT-N10

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37989

6 years agokernel: b53: use hard coded switch reset gpio on some boards.
Hauke Mehrtens [Sat, 14 Sep 2013 16:17:36 +0000 (16:17 +0000)]
kernel: b53: use hard coded switch reset gpio on some boards.

The Linksys wrt310n v1 does not have a robo_reset config variable in
nvram, but GPIO Pin 8 is the pin needed for resetting the external
switch, Linksys hard coded it into their source code.

Thank you Devastator for testing.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37988

6 years agokernel: b53: add soft reset for BCM539x switches
Hauke Mehrtens [Sat, 14 Sep 2013 16:14:02 +0000 (16:14 +0000)]
kernel: b53: add soft reset for BCM539x switches

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37987

6 years agobrcm47xx: tg3: use the phy address from et0phyaddr and not the default phy address.
Hauke Mehrtens [Sat, 14 Sep 2013 16:10:37 +0000 (16:10 +0000)]
brcm47xx: tg3: use the phy address from et0phyaddr and not the default phy address.

Thank you Devastator for testing.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37986

6 years agoath9k: add another minor tx path fix
Felix Fietkau [Sat, 14 Sep 2013 15:30:13 +0000 (15:30 +0000)]
ath9k: add another minor tx path fix

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37985

6 years agoiwinfo: when using nl80211, parse interface combinations instead of creating/deleting...
Felix Fietkau [Sat, 14 Sep 2013 14:46:51 +0000 (14:46 +0000)]
iwinfo: when using nl80211, parse interface combinations instead of creating/deleting interfaces

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37983

6 years agoath9k: merge a fix for tx processing issues with aggregation
Felix Fietkau [Sat, 14 Sep 2013 14:46:39 +0000 (14:46 +0000)]
ath9k: merge a fix for tx processing issues with aggregation

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37982

6 years agogeneric/3.10: remove unused defines from the rootfs split patch
Gabor Juhos [Sat, 14 Sep 2013 10:19:10 +0000 (10:19 +0000)]
generic/3.10: remove unused defines from the rootfs split patch

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37981

6 years agogeneric/3.10: reduce number of ifdefs in the rootfs split code
Gabor Juhos [Sat, 14 Sep 2013 10:19:09 +0000 (10:19 +0000)]
generic/3.10: reduce number of ifdefs in the rootfs split code

Use the config_enabled() macro where it is possible.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37980

6 years agoimx6: add network defaults for GW5400-A
Luka Perkov [Fri, 13 Sep 2013 21:50:35 +0000 (21:50 +0000)]
imx6: add network defaults for GW5400-A

Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37979

6 years agokernel: add missing config option
Hauke Mehrtens [Fri, 13 Sep 2013 20:39:23 +0000 (20:39 +0000)]
kernel: add missing config option

SVN-Revision: 37978

6 years agobrcm47xx: board detection, GPIO for Linksys E1000 V2.1
Hauke Mehrtens [Fri, 13 Sep 2013 19:24:08 +0000 (19:24 +0000)]
brcm47xx: board detection, GPIO for Linksys E1000 V2.1

This patch adds board detection for the Linksys E1000 V2.1 router, as well
as GPIO support for same.

This fixes bug #14135. Currently, wired networking isn't working on the
router, and I haven't tried the wireless, but with this patch, OpenWRT
successfully boots, and all the LEDs and buttons work properly.

Signed-off-by: Zachary Catlin <zcatlin@indiana.edu>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37977

6 years agoar71xx: refresh patches
Gabor Juhos [Fri, 13 Sep 2013 17:29:16 +0000 (17:29 +0000)]
ar71xx: refresh patches

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37976

6 years agogeneric/3.10: refresh patches
Gabor Juhos [Fri, 13 Sep 2013 17:29:14 +0000 (17:29 +0000)]
generic/3.10: refresh patches

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37975

6 years agogeneric/3.10: rename mtd patches
Gabor Juhos [Fri, 13 Sep 2013 17:24:25 +0000 (17:24 +0000)]
generic/3.10: rename mtd patches

  - change patch numbers to group the related stuff together,
  - add mtd prefix where it is missing,
  - use hyphens in the patch names

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37974

6 years agocns21xx: remove 3.8 support
Gabor Juhos [Fri, 13 Sep 2013 16:39:36 +0000 (16:39 +0000)]
cns21xx: remove 3.8 support

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37973

6 years agocns21xx: switch to 3.10
Gabor Juhos [Fri, 13 Sep 2013 16:39:34 +0000 (16:39 +0000)]
cns21xx: switch to 3.10

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37972

6 years agocns21xx: add support for 3.10
Gabor Juhos [Fri, 13 Sep 2013 16:39:33 +0000 (16:39 +0000)]
cns21xx: add support for 3.10

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37971

6 years agobrcm47xx: do not use GPIO configuration of WRT54G for every unknown Linksys device
Hauke Mehrtens [Fri, 13 Sep 2013 16:00:52 +0000 (16:00 +0000)]
brcm47xx: do not use GPIO configuration of WRT54G for every unknown Linksys device

Most of the Linksys devices without an own GPIO configuration where
detected as WRT54G. On one board this made OpenWrt to boot into
failsafe every time, because one GPIO configurated as button was not a
button.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37970

6 years agobrcm47xx: detect WRT310NV1
Hauke Mehrtens [Fri, 13 Sep 2013 15:56:35 +0000 (15:56 +0000)]
brcm47xx: detect WRT310NV1

Thanks Devastator for testing

SVN-Revision: 37969

6 years agocns21xx: make cns21xx-ehci a separate driver
Gabor Juhos [Fri, 13 Sep 2013 15:38:42 +0000 (15:38 +0000)]
cns21xx: make cns21xx-ehci a separate driver

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37968

6 years agocns21xx: disable legacy PTY devices
Gabor Juhos [Fri, 13 Sep 2013 15:38:41 +0000 (15:38 +0000)]
cns21xx: disable legacy PTY devices

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37967

6 years agocns21xx: fix broken case statement in led defaults file
Gabor Juhos [Fri, 13 Sep 2013 15:38:40 +0000 (15:38 +0000)]
cns21xx: fix broken case statement in led defaults file

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37966

6 years agocns21xx: enable XZ_DEC_ARM and XZ_DEC_BCJ kernel options
Gabor Juhos [Fri, 13 Sep 2013 15:38:39 +0000 (15:38 +0000)]
cns21xx: enable XZ_DEC_ARM and XZ_DEC_BCJ kernel options

Squashfs is unable to decompress some blocks without that:

  [    0.970000] SQUASHFS error: xz_dec_run error, data probably corrupt
  [    0.980000] SQUASHFS error: squashfs_read_data failed to read block 0x29a72
  [    0.990000] SQUASHFS error: Unable to read fragment cache entry [29a72]
  [    1.000000] SQUASHFS error: Unable to read page, block 29a72, size 14c50
  [    1.010000] SQUASHFS error: Unable to read fragment cache entry [29a72]
  [    1.020000] SQUASHFS error: Unable to read page, block 29a72, size 14c50
  [    1.260000] SQUASHFS error: xz_dec_run error, data probably corrupt

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37965

6 years agoar71xx: add support for TL-MR3040 v2
Gabor Juhos [Fri, 13 Sep 2013 15:28:50 +0000 (15:28 +0000)]
ar71xx: add support for TL-MR3040 v2

This patch adds support for building firmware images for the
TP-Link TL-MR3040 v2. Tested and working on v2.1 hardware.

Signed-off-by: Mads Hansen <d@taba.se>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37964

6 years agoar71xx: add wireless bgn led support for dir-825-c1
Gabor Juhos [Fri, 13 Sep 2013 15:01:40 +0000 (15:01 +0000)]
ar71xx: add wireless bgn led support for dir-825-c1

I checked the GPL code drop from D-Link and tried to get the wireless
and LAN switch LEDs to light up. I found some references in
AthSDK/www/DIR-825_C1/bsp.h as well as
AthSDK/www/DIR-825_C1/rootfs/etc/sysconfig/S2gpio.sh, but in the end I
only got the led for 2.4GHz to work. Anyway, here's the patch.

Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37963

6 years agouhttpd: udpat to git head
Jo-Philipp Wich [Fri, 13 Sep 2013 13:24:45 +0000 (13:24 +0000)]
uhttpd: udpat to git head

- fixes buffer corruption with JSON-RPC list calls
- change JSON-RPC protocol to include the session ID into the call
  attributes instead of passing it via the URL
- forcibly pass effective session ID as "ubus_rpc_session" attribute
  to called procedures
- change ubus acl checking to conform with new ubus session namespace

SVN-Revision: 37962

6 years agorpcd: update to git head
Jo-Philipp Wich [Fri, 13 Sep 2013 13:24:32 +0000 (13:24 +0000)]
rpcd: update to git head

- recalculate session ACLs on reload
- support negative access group expressions in /etc/config/rpcd
- prevent destryoing the default session
- use "ubus_rpc_session" attribute as session identifier to enforce JSON-RPC proxy security

SVN-Revision: 37961

6 years agokernel: gsc depends on kmod-i2c-core
Luka Perkov [Thu, 12 Sep 2013 23:38:54 +0000 (23:38 +0000)]
kernel: gsc depends on kmod-i2c-core

Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37960

6 years agobrcm47xx: remove support for kernel 3.8
Hauke Mehrtens [Thu, 12 Sep 2013 22:07:12 +0000 (22:07 +0000)]
brcm47xx: remove support for kernel 3.8

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37959

6 years agobrcm47xx: add default config for new kernel config option
Hauke Mehrtens [Thu, 12 Sep 2013 22:04:55 +0000 (22:04 +0000)]
brcm47xx: add default config for new kernel config option

SVN-Revision: 37958

6 years agokernel: update bcma and ssb to wireless-testing master-2013-09-09
Hauke Mehrtens [Thu, 12 Sep 2013 22:03:45 +0000 (22:03 +0000)]
kernel: update bcma and ssb to wireless-testing master-2013-09-09

SVN-Revision: 37957

6 years agokernel: add support for ESMT F25L32PA with upstream submission
Luka Perkov [Thu, 12 Sep 2013 14:38:48 +0000 (14:38 +0000)]
kernel: add support for ESMT F25L32PA with upstream submission

Signed-off-by: Flavio Silveira <fggs@terra.com.br>
SVN-Revision: 37956

6 years agoodhcp6c: Timing workaround for buggy servers
Steven Barth [Thu, 12 Sep 2013 12:57:42 +0000 (12:57 +0000)]
odhcp6c: Timing workaround for buggy servers

SVN-Revision: 37951

6 years agokernel: fix imx sata module
Luka Perkov [Wed, 11 Sep 2013 22:08:46 +0000 (22:08 +0000)]
kernel: fix imx sata module

The imx sata module has only been backported to imx6 target. This change will
fix buildbot errors due to missing patches in other targets. Keep this until
all targets use kernel version with imx sata support in them.

Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37950

6 years agokernel: align the skb padding to power of two
Felix Fietkau [Wed, 11 Sep 2013 14:30:15 +0000 (14:30 +0000)]
kernel: align the skb padding to power of two

The skb is usually started by a padding which allows the protocols in the
network stack to add their headers in front of the payload. The skb can be
reallocated in case the preallocated padding is not large enough. This can for
example happen in the function __skb_cow which will check the requested extra
headroom and allocate more buffer when the requested headroom is bigger than
the available one. The extra buffer is aligned again to the multiple of the
NET_SKB_PAD of the target architecture.

The macro used to create the multiple of the NET_SKB_PAD is written in a way
which allows only values power two as alignment parameter. The currently used
value of 48 bytes can not be written as n ** 2 but as 2 ** 4 + 2 ** 5. The
extra buffer is therefore not always the multiple of 48 but can be 16, 64, 80,
128, 144 and so on. The generated values are also not monotonic (48 requested
bytes are mapped to 80 allocated bytes and 49 requested bytes are mapped to 64
allocated bytes).

These unexpected small values result in more reallocations of the buffer. This
was noticed prominently during tests between two QCA9558 720 MHz devices which
were connected via ethernet to PCs and had a HT40 802.11n 3x3 link between each
other. The throughput PC-to-PC during iperf TCP runs increased reliable from
186 Mibit/s to 214 Mibit/s in one direction and from 195 Mibit/s to 220 Mibit/s
in the other direction. This is a performance increase of ~14% just by reducing
the amount of reallocations.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 37948

6 years agotoolchain/gcc: upgrade linaro gcc 4.6 to 4.6-2013.05
Felix Fietkau [Wed, 11 Sep 2013 14:29:44 +0000 (14:29 +0000)]
toolchain/gcc: upgrade linaro gcc 4.6 to 4.6-2013.05

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37947

6 years agotoolchain/gcc: fix up breakage introduced in r37945
Felix Fietkau [Wed, 11 Sep 2013 14:28:21 +0000 (14:28 +0000)]
toolchain/gcc: fix up breakage introduced in r37945

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37946

6 years ago[toolchain/gcc]: upgrade Linaro gcc 4.8 to 4.8-2013.08
Imre Kaloz [Wed, 11 Sep 2013 13:19:43 +0000 (13:19 +0000)]
[toolchain/gcc]: upgrade Linaro gcc 4.8 to 4.8-2013.08

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 37945

6 years ago[toolchain/binutils]: add support for Linaro binutils 2.23.2-2013.06
Imre Kaloz [Wed, 11 Sep 2013 13:18:23 +0000 (13:18 +0000)]
[toolchain/binutils]: add support for Linaro binutils 2.23.2-2013.06

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 37944

6 years ago[toolchain/gdb]: upgrade to 7.6-2013.05
Imre Kaloz [Wed, 11 Sep 2013 13:16:13 +0000 (13:16 +0000)]
[toolchain/gdb]: upgrade to 7.6-2013.05

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 37943

6 years agokernel: fix broken depends syntax introduced in r37933
Florian Fainelli [Wed, 11 Sep 2013 12:45:24 +0000 (12:45 +0000)]
kernel: fix broken depends syntax introduced in r37933

Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 37942

6 years agorpcd: update to git head
Jo-Philipp Wich [Wed, 11 Sep 2013 12:13:33 +0000 (12:13 +0000)]
rpcd: update to git head

- introduces persistent null session to allow access to procedures without login
- implements session.login procedure to support user logins via json-rpc

SVN-Revision: 37941

6 years agokernel: Fix FIQ code on VIVT CPUs (#14145)
Florian Fainelli [Wed, 11 Sep 2013 12:08:44 +0000 (12:08 +0000)]
kernel: Fix FIQ code on VIVT CPUs (#14145)

Backport an upstream patch to fix FIQ code on VIVT CPUs

Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 37940

6 years agotoolchain: refresh uClibc patches
Florian Fainelli [Wed, 11 Sep 2013 12:08:37 +0000 (12:08 +0000)]
toolchain: refresh uClibc patches

Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 37939

6 years agotoolchain: define MUSL dynamic linker for SPARC
Florian Fainelli [Wed, 11 Sep 2013 12:08:27 +0000 (12:08 +0000)]
toolchain: define MUSL dynamic linker for SPARC

SPARC builds are currently broken because we do not define the MUSL
dynamic linker name, fix that.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 37938

6 years agokernel: add imx sata module
Luka Perkov [Tue, 10 Sep 2013 22:26:37 +0000 (22:26 +0000)]
kernel: add imx sata module

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 37937

6 years agoimx6: backport ahci support
Luka Perkov [Tue, 10 Sep 2013 22:26:36 +0000 (22:26 +0000)]
imx6: backport ahci support

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37936

6 years agoimx6: add i2c retry on NAK
Luka Perkov [Tue, 10 Sep 2013 22:26:34 +0000 (22:26 +0000)]
imx6: add i2c retry on NAK

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 37935

6 years agoimx6: add gpio sysfs support
Luka Perkov [Tue, 10 Sep 2013 22:26:33 +0000 (22:26 +0000)]
imx6: add gpio sysfs support

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 37934

6 years agokernel: allow hwmon GSC driver for all targets
Luka Perkov [Tue, 10 Sep 2013 22:26:30 +0000 (22:26 +0000)]
kernel: allow hwmon GSC driver for all targets

- enable using hwmon GSC driver on all targets
- add a kmod package for it

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 37933

6 years agobuild: enable MIPS16 again, but make it depend on !gcc-4.6
Felix Fietkau [Tue, 10 Sep 2013 14:40:06 +0000 (14:40 +0000)]
build: enable MIPS16 again, but make it depend on !gcc-4.6

gcc 4.6 miscompiles hostapd with mips16, on gcc 4.8 it works

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37932

6 years agokernel: fix arch-dependent bug in hso module
Felix Fietkau [Tue, 10 Sep 2013 13:47:44 +0000 (13:47 +0000)]
kernel: fix arch-dependent bug in hso module

Currently, the module causes an oops at least on rt5350. These patches
have been accepted upstream at:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net.git

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 37931

6 years agoRevert "build: enable MIPS16 by default if available"
Felix Fietkau [Tue, 10 Sep 2013 12:33:21 +0000 (12:33 +0000)]
Revert "build: enable MIPS16 by default if available"

This reverts commit r37926.
It seems to trigger some weird issues in hostapd that should be
investigated first

SVN-Revision: 37928

6 years agoopenssl: add parallel build support
Felix Fietkau [Tue, 10 Sep 2013 12:09:13 +0000 (12:09 +0000)]
openssl: add parallel build support

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37927

6 years agobuild: enable MIPS16 by default if available
Felix Fietkau [Tue, 10 Sep 2013 12:09:07 +0000 (12:09 +0000)]
build: enable MIPS16 by default if available

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37926

6 years agoprocd: update to latest version, adds udevtrigger improvements by juhosg
Felix Fietkau [Tue, 10 Sep 2013 11:32:07 +0000 (11:32 +0000)]
procd: update to latest version, adds udevtrigger improvements by juhosg

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37925

6 years agotoolchain/gcc: remove 4.6.3, it is unused and unmaintained
Felix Fietkau [Tue, 10 Sep 2013 10:30:41 +0000 (10:30 +0000)]
toolchain/gcc: remove 4.6.3, it is unused and unmaintained

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37924

6 years agort2x00: merge an rt2800 initialization order fix
Felix Fietkau [Mon, 9 Sep 2013 17:31:53 +0000 (17:31 +0000)]
rt2x00: merge an rt2800 initialization order fix

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37922

6 years agorpcd: update to git head
Jo-Philipp Wich [Mon, 9 Sep 2013 14:35:15 +0000 (14:35 +0000)]
rpcd: update to git head

- adds support for service triggering on config commit
- adds uci transaction support
- adds daemon reload support without loosing session data
- exports headers for use by external plugins
- drops LuCI2 in favor to an out of tree plugin

SVN-Revision: 37921

6 years agoath9k: clean up some patches
Felix Fietkau [Sun, 8 Sep 2013 09:38:38 +0000 (09:38 +0000)]
ath9k: clean up some patches

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37919

6 years agomac80211: merge a big batch of upstream changes/improvements
Felix Fietkau [Sun, 8 Sep 2013 09:38:32 +0000 (09:38 +0000)]
mac80211: merge a big batch of upstream changes/improvements

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37918

6 years agotools/cmake: disable qt related checks to fix build issues
Felix Fietkau [Sat, 7 Sep 2013 18:33:07 +0000 (18:33 +0000)]
tools/cmake: disable qt related checks to fix build issues

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 37917

6 years agobrcm47xx: add me as maintainer
Hauke Mehrtens [Sat, 7 Sep 2013 15:46:27 +0000 (15:46 +0000)]
brcm47xx: add me as maintainer

SVN-Revision: 37916

6 years agoar71xx: use the lzma loader for the WRT160NL
Gabor Juhos [Sat, 7 Sep 2013 11:40:45 +0000 (11:40 +0000)]
ar71xx: use the lzma loader for the WRT160NL

Partition layout before:
  0x000000040000-0x0000001a0000 : "kernel"
  0x0000001a0000-0x0000007e0000 : "rootfs"
  mtd: partition "rootfs" set to be root filesystem
  mtd: partition "rootfs_data" created automatically, ofs=0x350000, len=0x490000
  0x000000350000-0x0000007e0000 : "rootfs_data"

after:
  0x000000040000-0x000000140000 : "kernel"
  0x000000140000-0x0000007e0000 : "rootfs"
  mtd: partition "rootfs" set to be root filesystem
  mtd: partition "rootfs_data" created automatically, ofs=0x2f0000, len=0x4f0000
  0x0000002f0000-0x0000007e0000 : "rootfs_data"

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37915

6 years agoppc40x: remove 3.8 support
Gabor Juhos [Sat, 7 Sep 2013 11:34:08 +0000 (11:34 +0000)]
ppc40x: remove 3.8 support

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37914

6 years agoppc40x: switch to 3.10
Gabor Juhos [Sat, 7 Sep 2013 11:34:06 +0000 (11:34 +0000)]
ppc40x: switch to 3.10

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37913

6 years agoppc40x: add support for 3.10
Gabor Juhos [Sat, 7 Sep 2013 11:34:03 +0000 (11:34 +0000)]
ppc40x: add support for 3.10

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 37912

6 years agobrcm63xx: drop linux 3.9 support
Jonas Gorski [Fri, 6 Sep 2013 19:01:17 +0000 (19:01 +0000)]
brcm63xx: drop linux 3.9 support

It is EOL since quite a while, so no need to keep it around.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37911

6 years agobrcm63xx: switch to linux 3.10
Jonas Gorski [Fri, 6 Sep 2013 19:01:13 +0000 (19:01 +0000)]
brcm63xx: switch to linux 3.10

3.10 is stable enough, and 3.9 is EOL since a while.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37910

6 years agoodhcp6c: more compatibility fixes
Steven Barth [Thu, 5 Sep 2013 21:13:51 +0000 (21:13 +0000)]
odhcp6c: more compatibility fixes

SVN-Revision: 37907

6 years agokernel: b53: support phy ids for BCM5365
Jonas Gorski [Thu, 5 Sep 2013 20:30:34 +0000 (20:30 +0000)]
kernel: b53: support phy ids for BCM5365

BCM5365 (and probably other older variants) use a different phy id, so
the phy driver never attached for them.
Fix this by adding the appropriate phy id to the fixup and the phy
driver.

Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 37906

6 years agomac80211: kmod-rtl_pci: fix dependencies
Hauke Mehrtens [Thu, 5 Sep 2013 20:17:28 +0000 (20:17 +0000)]
mac80211: kmod-rtl_pci: fix dependencies

This fixes the following error:
rtl_pci: Unknown symbol rtl_lps_leave (err 0)
rtl_pci: Unknown symbol rtl_lps_enter (err 0)
rtl8192ce: Unknown symbol rtl_pci_disconnect (err 0)
rtl8192ce: Unknown symbol rtl_pci_probe (err 0)
rtl8192de: Unknown symbol rtl_pci_disconnect (err 0)
rtl8192de: Unknown symbol rtl_pci_probe (err 0)
rtl8192se: Unknown symbol rtl_pci_disconnect (err 0)
rtl8192se: Unknown symbol rtl_pci_probe (err 0)

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37905

6 years agokernel: kmod-libphy, kmod-tg3: fix load order
Hauke Mehrtens [Thu, 5 Sep 2013 19:57:44 +0000 (19:57 +0000)]
kernel: kmod-libphy, kmod-tg3: fix load order

This fixes the following error:
tg3: Unknown symbol mdiobus_alloc_size (err 0)
tg3: Unknown symbol phy_ethtool_sset (err 0)
tg3: Unknown symbol phy_mii_ioctl (err 0)
tg3: Unknown symbol phy_connect (err 0)
tg3: Unknown symbol mdiobus_register (err 0)
tg3: Unknown symbol mdiobus_free (err 0)
tg3: Unknown symbol phy_start (err 0)
tg3: Unknown symbol phy_start_aneg (err 0)
tg3: Unknown symbol mdiobus_unregister (err 0)
tg3: Unknown symbol phy_ethtool_gset (err 0)
tg3: Unknown symbol phy_stop (err 0)
tg3: Unknown symbol phy_disconnect (err 0)

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37904

6 years agokernel: kmod-ssb, kmod-b44: fix load order
Hauke Mehrtens [Thu, 5 Sep 2013 19:56:04 +0000 (19:56 +0000)]
kernel: kmod-ssb, kmod-b44: fix load order

This fixes the following error:
b44: Unknown symbol ssb_device_is_enabled (err 0)
b44: Unknown symbol ssb_pcicore_dev_irqvecs_enable (err 0)
b44: Unknown symbol ssb_bus_may_powerdown (err 0)
b44: Unknown symbol ssb_pcihost_register (err 0)
b44: Unknown symbol ssb_device_disable (err 0)
b44: Unknown symbol ssb_device_enable (err 0)
b44: Unknown symbol ssb_driver_unregister (err 0)
b44: Unknown symbol __ssb_driver_register (err 0)
b44: Unknown symbol ssb_bus_powerup (err 0)
b44: Unknown symbol ssb_clockspeed (err 0)
b44: Unknown symbol ssb_dma_translation (err 0)

Reported-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37903

6 years agokernel: kmod-firewire: fix dependencies
Hauke Mehrtens [Thu, 5 Sep 2013 19:53:21 +0000 (19:53 +0000)]
kernel: kmod-firewire: fix dependencies

This fixes the following error:
firewire_core: Unknown symbol crc_itu_t (err 0)

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37902

6 years agomac80211: do not download carl9170 firmware separately, but use the one from linux...
Hauke Mehrtens [Thu, 5 Sep 2013 19:43:38 +0000 (19:43 +0000)]
mac80211: do not download carl9170 firmware separately, but use the one from linux-firemware

linux-firemware contains the same version we loaded without this patch.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37901

6 years agokernel: kmod-fs-xfs: fix dependencies
Hauke Mehrtens [Thu, 5 Sep 2013 19:41:00 +0000 (19:41 +0000)]
kernel: kmod-fs-xfs: fix dependencies

This fixes the following error:
xfs: Unknown symbol exportfs_decode_fh (err 0)

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37900

6 years agokernel: kmod-usb-serial-keyspan: fix dependencies
Hauke Mehrtens [Thu, 5 Sep 2013 19:39:55 +0000 (19:39 +0000)]
kernel: kmod-usb-serial-keyspan: fix dependencies

This fixes the following error:
keyspan: Unknown symbol ezusb_fx1_ihex_firmware_download (err 0)

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37899

6 years agoath10k: enable Atheros 802.11ac driver
Hauke Mehrtens [Thu, 5 Sep 2013 19:35:14 +0000 (19:35 +0000)]
ath10k: enable Atheros 802.11ac driver

This enables usage of the ath10k driver on OpenWrt. Only 2.0 PCI hardware
is supported. The ath10k firmware is currently only available
through github so use that as its source for now.

This goes build tested, not run time tested.

[Hauke: I did some minor changes]

Cc: ath10k@lists.infradead.org
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Kathy Giori <kgiori@qca.qualcomm.com>
Cc: Mathieu Olivari <mathieu@qca.qualcomm.com>
Cc: Jerome Proffit <jproffit@qca.qualcomm.com>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: Matthew McClintock <mmcclint@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37898

6 years agoAdd missing symbol
Imre Kaloz [Thu, 5 Sep 2013 10:08:59 +0000 (10:08 +0000)]
Add missing symbol

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 37897

6 years agokernel: b53: allow access the MIB counters on BCM5365
Hauke Mehrtens [Wed, 4 Sep 2013 16:15:10 +0000 (16:15 +0000)]
kernel: b53: allow access the MIB counters on BCM5365

b53_no_ops has no elements and b53_port_ops has one element, this makes
the code access some random memory when trying to access the mib
counter functions.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37895

6 years ago[package] kobs-ng: add new package
Luka Perkov [Tue, 3 Sep 2013 23:22:16 +0000 (23:22 +0000)]
[package] kobs-ng: add new package

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 37894

6 years agousbreset: rewrite to not rely on /proc/bus/usb anymore
Jo-Philipp Wich [Tue, 3 Sep 2013 15:46:39 +0000 (15:46 +0000)]
usbreset: rewrite to not rely on /proc/bus/usb anymore

SVN-Revision: 37893