openwrt/svn-archive/archive.git
8 years agoar71xx: fix AR934X_EHCI_SIZE
Gabor Juhos [Thu, 2 Aug 2012 11:25:46 +0000 (11:25 +0000)]
ar71xx: fix AR934X_EHCI_SIZE

SVN-Revision: 32947

8 years agoar71xx: image: stop the switch from the lzma-loader on the TL-WR1043ND
Gabor Juhos [Thu, 2 Aug 2012 09:54:41 +0000 (09:54 +0000)]
ar71xx: image: stop the switch from the lzma-loader on the TL-WR1043ND

SVN-Revision: 32946

8 years agoar71xx: image: allow to use board specific code in the lzma-loader
Gabor Juhos [Thu, 2 Aug 2012 09:54:33 +0000 (09:54 +0000)]
ar71xx: image: allow to use board specific code in the lzma-loader

SVN-Revision: 32945

8 years agoar71xx: init switch hw_reset on the TL-WR1043ND board
Gabor Juhos [Thu, 2 Aug 2012 09:54:28 +0000 (09:54 +0000)]
ar71xx: init switch hw_reset on the TL-WR1043ND board

SVN-Revision: 32944

8 years agogeneric: rtl836x: add hw_reset field to struct rtl8366_smi
Gabor Juhos [Thu, 2 Aug 2012 09:54:21 +0000 (09:54 +0000)]
generic: rtl836x: add hw_reset field to struct rtl8366_smi

It will be used to start/stop the switch if that is
supported by the given board.

SVN-Revision: 32943

8 years agogeneric: rtl8366_smi: use __rtl8366_smi_cleanup instead of gpio_free calls
Gabor Juhos [Thu, 2 Aug 2012 09:54:13 +0000 (09:54 +0000)]
generic: rtl8366_smi: use __rtl8366_smi_cleanup instead of gpio_free calls

SVN-Revision: 32942

8 years ago[mcs814x] add missing netmask to the network config
Florian Fainelli [Wed, 1 Aug 2012 22:09:13 +0000 (22:09 +0000)]
[mcs814x] add missing netmask to the network config

SVN-Revision: 32941

8 years ago[mcs814x] assume the link is up and full-duplex by default
Florian Fainelli [Wed, 1 Aug 2012 21:56:54 +0000 (21:56 +0000)]
[mcs814x] assume the link is up and full-duplex by default

SVN-Revision: 32940

8 years ago[mcs814x] add a default and suitable network config file
Florian Fainelli [Wed, 1 Aug 2012 21:56:49 +0000 (21:56 +0000)]
[mcs814x] add a default and suitable network config file

SVN-Revision: 32939

8 years agoar71xx: ew-dorin: added router firmware generation
Gabor Juhos [Wed, 1 Aug 2012 12:24:57 +0000 (12:24 +0000)]
ar71xx: ew-dorin: added router firmware generation

[juhosg: remove dead code]

Signed-off-by: embedded wireless GmbH <info@embeddedwireless.de>
SVN-Revision: 32934

8 years agoar71xx: ew-dorin: added USB support
Gabor Juhos [Wed, 1 Aug 2012 12:24:56 +0000 (12:24 +0000)]
ar71xx: ew-dorin: added USB support

Signed-off-by: embedded wireless GmbH <info@embeddedwireless.de>
SVN-Revision: 32933

8 years agoar71xx: Buffalo WLAE-AG300N wireless led patch
Gabor Juhos [Wed, 1 Aug 2012 12:24:54 +0000 (12:24 +0000)]
ar71xx: Buffalo WLAE-AG300N wireless led patch

Here is the uci-defaults version of the led support for
the Buffalo WLAE-AG300N.

Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32932

8 years agoar71xx: Buffalo WLAE-AG300N initial support
Gabor Juhos [Wed, 1 Aug 2012 12:24:52 +0000 (12:24 +0000)]
ar71xx: Buffalo WLAE-AG300N initial support

The patch set for Buffalo WLAE-AG300N initial support.

There is another patch for wireless led support that
is posted separately.

Note on serial console:
This unit has buffalo standard 4 pin console, but the unit may not power
on if some console apparatus is connected. This is probably due to some
electronic interaction between the unit's electronic power switch circuit
and the serial console apparatus. If this happens, it is required to power
on the unit without the console, then quickly (re-)attach it.

[juhosg: fix coding style]

Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32931

8 years ago[mcs814x] resync defconfig enable XZ compression
Florian Fainelli [Wed, 1 Aug 2012 12:01:27 +0000 (12:01 +0000)]
[mcs814x] resync defconfig enable XZ compression

SVN-Revision: 32930

8 years ago[package] uclibc++: update to 0.2.4
Florian Fainelli [Wed, 1 Aug 2012 12:01:24 +0000 (12:01 +0000)]
[package] uclibc++: update to 0.2.4

SVN-Revision: 32929

8 years ago[package] uclibc++: stage g++-uc wrappers in $(TOOLCHAIN_DIR)
Florian Fainelli [Wed, 1 Aug 2012 12:01:18 +0000 (12:01 +0000)]
[package] uclibc++: stage g++-uc wrappers in $(TOOLCHAIN_DIR)

Since we are overriding TARGET_CXX with the g++-uc wrapper when
we use cmake it expects to find g++-uc in the TOOLCHAIN_DIR.

SVN-Revision: 32928

8 years ago[mcs814x] properly generate squashfs, jffs2 and initramfs images and kernels
Florian Fainelli [Tue, 31 Jul 2012 23:09:50 +0000 (23:09 +0000)]
[mcs814x] properly generate squashfs, jffs2 and initramfs images and kernels

SVN-Revision: 32927

8 years ago[kernel] disable crashlog on ARM platforms for the moment
Florian Fainelli [Tue, 31 Jul 2012 23:09:46 +0000 (23:09 +0000)]
[kernel] disable crashlog on ARM platforms for the moment

It is currently badly broken on ARM, until fixed, disable it

SVN-Revision: 32926

8 years ago[lantiq] add lantiq svip support
John Crispin [Tue, 31 Jul 2012 18:49:54 +0000 (18:49 +0000)]
[lantiq] add lantiq svip support

SVN-Revision: 32925

8 years agobcm63xx: Add nb6 support (BCM6362 SoC base boards)
Jonas Gorski [Tue, 31 Jul 2012 14:27:47 +0000 (14:27 +0000)]
bcm63xx: Add nb6 support (BCM6362 SoC base boards)

Signed-off-by: Miguel GAIO <miguel.gaio@efixo.com>
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
[jonas.gorski@gmail.com: add network config for nb6, make switch fix a
platform patch]

SVN-Revision: 32924

8 years agobcm63xx: add basic bcm6362 support
Jonas Gorski [Tue, 31 Jul 2012 14:27:42 +0000 (14:27 +0000)]
bcm63xx: add basic bcm6362 support

Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 32923

8 years agobcm63xx: enable usb for bcm6328
Jonas Gorski [Tue, 31 Jul 2012 14:27:34 +0000 (14:27 +0000)]
bcm63xx: enable usb for bcm6328

Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 32922

8 years agobcm63xx: update enetswitch driver
Jonas Gorski [Tue, 31 Jul 2012 14:27:31 +0000 (14:27 +0000)]
bcm63xx: update enetswitch driver

Update enetswith driver with latest fixes and additions.

Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 32921

8 years agobcm63xx: reorder patches
Jonas Gorski [Tue, 31 Jul 2012 14:27:25 +0000 (14:27 +0000)]
bcm63xx: reorder patches

Fix the order and names of patches.

Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 32920

8 years ago[at91] move i2c module to target modules.mk
Florian Fainelli [Sun, 29 Jul 2012 13:20:51 +0000 (13:20 +0000)]
[at91] move i2c module to target modules.mk

SVN-Revision: 32910

8 years ago[package] partially revert r32855
Florian Fainelli [Sun, 29 Jul 2012 13:20:47 +0000 (13:20 +0000)]
[package] partially revert r32855

Too many modules were removed, while only the octeon module was meant to be
removed, fix that.

SVN-Revision: 32909

8 years ago[omap24xx] resync config
Florian Fainelli [Sun, 29 Jul 2012 13:20:39 +0000 (13:20 +0000)]
[omap24xx] resync config

SVN-Revision: 32908

8 years ago[omap24xx] use the same description as other omap platforms (without the dash)
Florian Fainelli [Sun, 29 Jul 2012 13:20:35 +0000 (13:20 +0000)]
[omap24xx] use the same description as other omap platforms (without the dash)

SVN-Revision: 32907

8 years ago[kernel] refresh pwm patch
John Crispin [Sun, 29 Jul 2012 11:53:06 +0000 (11:53 +0000)]
[kernel] refresh pwm patch

SVN-Revision: 32905

8 years ago[acx-mac80211] dont build on arm as kernel headers are missing/have a different layout
John Crispin [Sun, 29 Jul 2012 09:07:47 +0000 (09:07 +0000)]
[acx-mac80211] dont build on arm as kernel headers are missing/have a different layout

SVN-Revision: 32904

8 years ago[include] fix up scons vs ccache
John Crispin [Sat, 28 Jul 2012 21:06:59 +0000 (21:06 +0000)]
[include] fix up scons vs ccache

SVN-Revision: 32902

8 years ago[kernel] clean up pwm patches and drivers
John Crispin [Sat, 28 Jul 2012 20:47:08 +0000 (20:47 +0000)]
[kernel] clean up pwm patches and drivers

SVN-Revision: 32901

8 years ago[kernel] add config option CONFIG_I2C_MV64XXX to fix kirkwood build
Hauke Mehrtens [Sat, 28 Jul 2012 11:36:52 +0000 (11:36 +0000)]
[kernel] add config option CONFIG_I2C_MV64XXX to fix kirkwood build

SVN-Revision: 32898

8 years ago[realview] resync config
Florian Fainelli [Fri, 27 Jul 2012 15:35:15 +0000 (15:35 +0000)]
[realview] resync config

SVN-Revision: 32895

8 years ago[brcm63xx] fix DVA-G3810BN image generation
Florian Fainelli [Fri, 27 Jul 2012 15:35:12 +0000 (15:35 +0000)]
[brcm63xx] fix DVA-G3810BN image generation

Attached patch fixes a typo in the image Makefile, and overrides the
board name for DVA-G3810BN to set the correct board properties

Signed-Off-By: Jeroen van Bemmel <jbemmel@zonnet.nl>
SVN-Revision: 32894

8 years ago[brcm63xx] add D-link DVA-G3810BN-TL-1 support
Florian Fainelli [Fri, 27 Jul 2012 15:35:09 +0000 (15:35 +0000)]
[brcm63xx] add D-link DVA-G3810BN-TL-1 support

Signed-Off-By: Jeroen van Bemmel <jbemmel@zonnet.nl>
SVN-Revision: 32893

8 years ago[brcm63xx] Add CT6376-1 board support
Florian Fainelli [Fri, 27 Jul 2012 15:35:05 +0000 (15:35 +0000)]
[brcm63xx] Add CT6376-1 board support

Added CT6373 devices instead of using NB4's devices, as Florian suggested.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 32892

8 years ago[package] base-files: fix detection of standalone ldd
Florian Fainelli [Fri, 27 Jul 2012 15:35:00 +0000 (15:35 +0000)]
[package] base-files: fix detection of standalone ldd

When standalone ldd is selected in config the binary is installed in /usr/bin/ldd.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 32891

8 years ago[brcm63xx] Add brcmsmac profile
Florian Fainelli [Fri, 27 Jul 2012 15:34:57 +0000 (15:34 +0000)]
[brcm63xx] Add brcmsmac profile

Add brcmsmac profile (kmod-brcmsmac + wpad-mini).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 32890

8 years ago[mac80211] mae brcmutil depend on PCI and USB. This broke ar7 fullbuilds
John Crispin [Fri, 27 Jul 2012 08:30:05 +0000 (08:30 +0000)]
[mac80211] mae brcmutil depend on PCI and USB. This broke ar7 fullbuilds

SVN-Revision: 32886

8 years ago[atheros] Add leds back after migration to sysfs
John Crispin [Thu, 26 Jul 2012 17:06:55 +0000 (17:06 +0000)]
[atheros] Add leds back after migration to sysfs

atheros trunk moved to full sysfs gpiolib, but the leds were forgotten.
This restores the wlan led that was missing after switching from backfire
to trunk.

Signed-off-by: Karl Palsson <karlp@remake.is>
SVN-Revision: 32885

8 years ago[brcm2708] add more missing config symbols
Florian Fainelli [Thu, 26 Jul 2012 17:03:08 +0000 (17:03 +0000)]
[brcm2708] add more missing config symbols

SVN-Revision: 32884

8 years ago[generic] add more USB-related config symbols
Florian Fainelli [Thu, 26 Jul 2012 17:03:05 +0000 (17:03 +0000)]
[generic] add more USB-related config symbols

SVN-Revision: 32883

8 years ago[ep93xx] make sure target modules depend on the target
Florian Fainelli [Thu, 26 Jul 2012 17:03:02 +0000 (17:03 +0000)]
[ep93xx] make sure target modules depend on the target

SVN-Revision: 32882

8 years ago[kernel] bcma: update to version from wireless-testing tag master-2012-07-16
Hauke Mehrtens [Thu, 26 Jul 2012 15:42:18 +0000 (15:42 +0000)]
[kernel] bcma: update to version from wireless-testing tag master-2012-07-16

I did not add the last patch, because it add some stubs for the flash drivers and our patches have to be changed for that, if the flash support in bcma is able to do something I will integrate it.

This also contains 3 additional patches fixing some bugs in bcma.

SVN-Revision: 32880

8 years ago[package] make kmod-mvsas depend on x86 since it fails building on other targets...
Florian Fainelli [Thu, 26 Jul 2012 09:29:22 +0000 (09:29 +0000)]
[package] make kmod-mvsas depend on x86 since it fails building on other targets (eg: brcm63xx)

SVN-Revision: 32878

8 years ago[ar71xx] fix typo in modules.mk
John Crispin [Wed, 25 Jul 2012 19:52:30 +0000 (19:52 +0000)]
[ar71xx] fix typo in modules.mk

This patch fixes a small typo in kmod-leds-wndr3700-usb description, where the board is for some reason made by NETGWR, not NETGEAR.

Signed-off-by: Roman A. aka BasicXP <x12ozmouse@ya.ru>
SVN-Revision: 32870

8 years ago[package] make kmod-fb dependent on DISPLAY_SUPPORT and update targets accordingly
Florian Fainelli [Wed, 25 Jul 2012 19:36:19 +0000 (19:36 +0000)]
[package] make kmod-fb dependent on DISPLAY_SUPPORT and update targets accordingly

SVN-Revision: 32869

8 years agomtd: fix trx_fixup
Felix Fietkau [Wed, 25 Jul 2012 17:28:32 +0000 (17:28 +0000)]
mtd: fix trx_fixup

With the BRCM47xx image I have built (Linksys E3000), there are additional
writes following the completion of "mtd_replace_jffs2" which invalidate the
'trx_fixup' performed by 'mtd_replace_jffs2'.  Moving the 'trx_fixup' to somewhere
after all writes have completed fixes the problem.  I also noticed that 'erasesize'
used to compute 'block_offset' in 'mtd_fixtrx' is used before it is computed by
'mtd_check_open'; moving the call to 'mtd_check_open' up a few lines fixes this.

Unlike 'mtd_fixtrx', 'trx_fixup' appears to assume that the TRX header is always at
offset 0; which may be the cause of the problem described in Ticket #8960.

Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 32866

8 years ago[ppc40x] move isp116x driver to target specific modules.mk
Florian Fainelli [Wed, 25 Jul 2012 15:50:45 +0000 (15:50 +0000)]
[ppc40x] move isp116x driver to target specific modules.mk

SVN-Revision: 32865

8 years ago[ramips] move rt305x-dwc driver to target specific modules.mk
Florian Fainelli [Wed, 25 Jul 2012 15:50:42 +0000 (15:50 +0000)]
[ramips] move rt305x-dwc driver to target specific modules.mk

SVN-Revision: 32864

8 years ago[brcm47xx] move ubsec-ssb driver to target specific modules.mk
Florian Fainelli [Wed, 25 Jul 2012 15:50:38 +0000 (15:50 +0000)]
[brcm47xx] move ubsec-ssb driver to target specific modules.mk

SVN-Revision: 32863

8 years ago[brcm47xx] move ssb-gige to target specific modules.mk
Florian Fainelli [Wed, 25 Jul 2012 15:50:36 +0000 (15:50 +0000)]
[brcm47xx] move ssb-gige to target specific modules.mk

SVN-Revision: 32862

8 years ago[brcm47xx] move usb driver to target specific modules.mk
Florian Fainelli [Wed, 25 Jul 2012 15:50:33 +0000 (15:50 +0000)]
[brcm47xx] move usb driver to target specific modules.mk

SVN-Revision: 32861

8 years ago[package] kmod-r6040 depends on PCI_SUPPORT
Florian Fainelli [Wed, 25 Jul 2012 15:50:29 +0000 (15:50 +0000)]
[package] kmod-r6040 depends on PCI_SUPPORT

SVN-Revision: 32860

8 years ago[avr32] move mmc driver to target specific modules.mk
Florian Fainelli [Wed, 25 Jul 2012 15:50:26 +0000 (15:50 +0000)]
[avr32] move mmc driver to target specific modules.mk

SVN-Revision: 32859

8 years ago[ixp4xx] move ixp4xx-eth to target specific modules.mk
Florian Fainelli [Wed, 25 Jul 2012 15:50:23 +0000 (15:50 +0000)]
[ixp4xx] move ixp4xx-eth to target specific modules.mk

SVN-Revision: 32858

8 years ago[package] kmod-gpio-nxp74hc164 is not brcm63xx specific
Florian Fainelli [Wed, 25 Jul 2012 15:50:20 +0000 (15:50 +0000)]
[package] kmod-gpio-nxp74hc164 is not brcm63xx specific

SVN-Revision: 32857

8 years ago[ixp4xx] move crypto module to target specific modules.mk
Florian Fainelli [Wed, 25 Jul 2012 15:50:16 +0000 (15:50 +0000)]
[ixp4xx] move crypto module to target specific modules.mk

SVN-Revision: 32856

8 years ago[octeon] move i2c driver to target modules.mk
Florian Fainelli [Wed, 25 Jul 2012 15:50:13 +0000 (15:50 +0000)]
[octeon] move i2c driver to target modules.mk

SVN-Revision: 32855

8 years ago[ar71xx] move watchdog driver to target specific modules.mk
Florian Fainelli [Wed, 25 Jul 2012 15:50:10 +0000 (15:50 +0000)]
[ar71xx] move watchdog driver to target specific modules.mk

SVN-Revision: 32854

8 years ago[ar71xx] move target specific spi modules
Florian Fainelli [Wed, 25 Jul 2012 15:50:04 +0000 (15:50 +0000)]
[ar71xx] move target specific spi modules

SVN-Revision: 32853

8 years ago[ar71xx] move target specific leds modules to ar71xx modules.mk
Florian Fainelli [Wed, 25 Jul 2012 15:50:02 +0000 (15:50 +0000)]
[ar71xx] move target specific leds modules to ar71xx modules.mk

SVN-Revision: 32852

8 years ago[x86] move leds modules back to target modules.mk
Florian Fainelli [Wed, 25 Jul 2012 15:49:57 +0000 (15:49 +0000)]
[x86] move leds modules back to target modules.mk

SVN-Revision: 32851

8 years ago[x86] move i2c modules back to target modules.mk
Florian Fainelli [Wed, 25 Jul 2012 15:49:54 +0000 (15:49 +0000)]
[x86] move i2c modules back to target modules.mk

SVN-Revision: 32850

8 years ago[package] fix network devices modules to depend on PCI instead of x86
Florian Fainelli [Wed, 25 Jul 2012 15:49:52 +0000 (15:49 +0000)]
[package] fix network devices modules to depend on PCI instead of x86

SVN-Revision: 32849

8 years ago[x86] move more x86-specific modules back to target modules.mk
Florian Fainelli [Wed, 25 Jul 2012 15:49:49 +0000 (15:49 +0000)]
[x86] move more x86-specific modules back to target modules.mk

SVN-Revision: 32848

8 years ago[package] fix libsas and mvsas dependencies against PCI and not x86
Florian Fainelli [Wed, 25 Jul 2012 15:49:46 +0000 (15:49 +0000)]
[package] fix libsas and mvsas dependencies against PCI and not x86

SVN-Revision: 32847

8 years ago[x86] move x86 specific ide/pata modules to x86' modules.mk
Florian Fainelli [Wed, 25 Jul 2012 15:49:42 +0000 (15:49 +0000)]
[x86] move x86 specific ide/pata modules to x86' modules.mk

SVN-Revision: 32846

8 years agobrcm47xx: reorder patches so that the patches already in mainline linux will be appli...
Hauke Mehrtens [Wed, 25 Jul 2012 14:52:00 +0000 (14:52 +0000)]
brcm47xx: reorder patches so that the patches already in mainline linux will be applied at first.

SVN-Revision: 32845

8 years ago[kernel] add yet another framebuffer symbol
Florian Fainelli [Wed, 25 Jul 2012 14:01:57 +0000 (14:01 +0000)]
[kernel] add yet another framebuffer symbol

SVN-Revision: 32844

8 years ago[package] split framebuffer helper modules to their own packages
Florian Fainelli [Wed, 25 Jul 2012 14:01:54 +0000 (14:01 +0000)]
[package] split framebuffer helper modules to their own packages

SVN-Revision: 32843

8 years ago[cobalt] remove broken flag
Florian Fainelli [Wed, 25 Jul 2012 14:01:51 +0000 (14:01 +0000)]
[cobalt] remove broken flag

SVN-Revision: 32842

8 years ago[cobalt] package buttons driver separately
Florian Fainelli [Wed, 25 Jul 2012 14:01:49 +0000 (14:01 +0000)]
[cobalt] package buttons driver separately

SVN-Revision: 32841

8 years ago[cobalt] package cobalt lcd as a module
Florian Fainelli [Wed, 25 Jul 2012 14:01:46 +0000 (14:01 +0000)]
[cobalt] package cobalt lcd as a module

SVN-Revision: 32840

8 years ago[include] use autoreconf hook instead of manual call
John Crispin [Wed, 25 Jul 2012 10:34:06 +0000 (10:34 +0000)]
[include] use autoreconf hook instead of manual call

SVN-Revision: 32837

8 years ago[kernel] add unset CONFIG_FB_XGI to fix fullbuilds
John Crispin [Wed, 25 Jul 2012 09:05:23 +0000 (09:05 +0000)]
[kernel] add unset CONFIG_FB_XGI to fix fullbuilds

SVN-Revision: 32836

8 years ago[brcm2708] cleanup config-3.3, remove =m
John Crispin [Wed, 25 Jul 2012 09:05:18 +0000 (09:05 +0000)]
[brcm2708] cleanup config-3.3, remove =m

SVN-Revision: 32835

8 years ago[cns3xx] laguna: fix eeprom read buffer size during platform configuration
John Crispin [Wed, 25 Jul 2012 08:01:38 +0000 (08:01 +0000)]
[cns3xx] laguna: fix eeprom read buffer size during platform configuration

Increase the size of the buffer used for eeprom reads during the platform configuration of the Gateworks laguna.  The model name read in is 16 bytes but the original buffer was only 8 bytes.

Signed-off-by: David Acker <dacker@rajant.com>
SVN-Revision: 32833

8 years ago[compcache] fixes build for 3.x kernel and remove old 2.6.x references
John Crispin [Tue, 24 Jul 2012 23:07:35 +0000 (23:07 +0000)]
[compcache] fixes build for 3.x kernel and remove old 2.6.x references

Signed-off-by: christoph.thielecke@gmx.de
SVN-Revision: 32832

8 years ago[include] package-version-override always calls autoreconf
John Crispin [Tue, 24 Jul 2012 23:07:30 +0000 (23:07 +0000)]
[include] package-version-override always calls autoreconf

make it conditional on the existance of autoreconf

Signed-off-by: Ryan Nowakowski <tubaman@fattuba.com>
SVN-Revision: 32831

8 years agomac80211/hostapd: add support for HT capa in case of IBSS/RSN
John Crispin [Tue, 24 Jul 2012 23:07:25 +0000 (23:07 +0000)]
mac80211/hostapd: add support for HT capa in case of IBSS/RSN

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
SVN-Revision: 32830

8 years agowpa_supplicant: add more parameters
John Crispin [Tue, 24 Jul 2012 23:07:15 +0000 (23:07 +0000)]
wpa_supplicant: add more parameters

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
SVN-Revision: 32829

8 years agohostapd: add pending patches
John Crispin [Tue, 24 Jul 2012 23:07:10 +0000 (23:07 +0000)]
hostapd: add pending patches

add patched needed to pass more parameters to the IBSS JOIN command

Signed-off-by: Antonio Quartulli <ordex@autistici.org>
SVN-Revision: 32828

8 years ago[brcm2708] adds target used by rapsberry pi
John Crispin [Tue, 24 Jul 2012 20:39:17 +0000 (20:39 +0000)]
[brcm2708] adds target used by rapsberry pi

Add support for Raspberry Pi / brcm2708 / 2835

Signed-off-by: Ian Ridge <ianridge [at] gmail.com>
SVN-Revision: 32825

8 years ago[tools] add mktools and dosfstools which are needed for the raspberry pi
John Crispin [Tue, 24 Jul 2012 20:39:00 +0000 (20:39 +0000)]
[tools] add mktools and dosfstools which are needed for the raspberry pi

Signed-off-by: Ian Ridge <ianridge [at] gmail.com>
SVN-Revision: 32824

8 years ago[ramips] DWC otg usb: compilation fixes and trivial bugfix in slave mode
John Crispin [Tue, 24 Jul 2012 20:38:55 +0000 (20:38 +0000)]
[ramips] DWC otg usb: compilation fixes and trivial bugfix in slave mode

Signed-of-by: Nikolai Zhubr <n-a-zhubr@yandex.ru>
SVN-Revision: 32823

8 years ago[tools] adds mkdapimg
John Crispin [Tue, 24 Jul 2012 20:38:49 +0000 (20:38 +0000)]
[tools] adds mkdapimg

Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32822

8 years ago[ramips] D-Link DAP-1350 initial support
John Crispin [Tue, 24 Jul 2012 20:38:43 +0000 (20:38 +0000)]
[ramips] D-Link DAP-1350 initial support

The initial support for the D-Link DAP-1350.
USB related functionality is not tested.

Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32821

8 years ago[ixp4xx] MI424WR - add rev D support
John Crispin [Tue, 24 Jul 2012 20:38:36 +0000 (20:38 +0000)]
[ixp4xx] MI424WR - add rev D support

Add support for revision D of the MI424WR.
Rev D swaps LAN & WAN ports so this patch maintains
eth0 for LAN and eth1 for WAN. For details on rev D usage,
see http://wiki.openwrt.org/toh/actiontec/mi424wr

Signed-off-by: Jose Vasconcellos <jvasco@verizon.net>
SVN-Revision: 32820

8 years ago[ramips] initial LED configuration for Fonera 2.0n
John Crispin [Tue, 24 Jul 2012 20:38:31 +0000 (20:38 +0000)]
[ramips] initial LED configuration for Fonera 2.0n

Setup initial configuration for Wifi and USB LEDS of a Fonera 2.0n (ramips)

Signed-off-by: Malte Forkel <malte.forkel@berlin.de>
SVN-Revision: 32819

8 years ago[mountd] ext4 support
John Crispin [Tue, 24 Jul 2012 20:38:26 +0000 (20:38 +0000)]
[mountd] ext4 support

This patch adds the ext4 filesystem support to mountd. Tested with ext2, ext3
and ext4 partitions.

Signed-off-by: Jaroslaw Swierczynski <jarek1701@gmail.com>
SVN-Revision: 32818

8 years ago[mac80211] add support for Rt3352 in rt2x00 driver
John Crispin [Tue, 24 Jul 2012 20:38:20 +0000 (20:38 +0000)]
[mac80211] add support for Rt3352 in rt2x00 driver

Forgot to do make package/mac80211/update, so the previously posted patch wasn't
in sync with compat-wireless. Now fixed.

Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32817

8 years ago[ramips] add ALL5002 userspace support
John Crispin [Tue, 24 Jul 2012 20:38:14 +0000 (20:38 +0000)]
[ramips] add ALL5002 userspace support

detect EEPROM, MAC addresses and support sysupgrade for the ALL5002

Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32816

8 years ago[ramips] enable OHCI/EHCI glue on Rt305x, so it is available for Rt3352F.
John Crispin [Tue, 24 Jul 2012 20:38:08 +0000 (20:38 +0000)]
[ramips] enable OHCI/EHCI glue on Rt305x, so it is available for Rt3352F.

Hope that this works, didn't have a chance to actually test it...

Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32815

8 years ago[ramips] add image build for ALL5002
John Crispin [Tue, 24 Jul 2012 20:38:03 +0000 (20:38 +0000)]
[ramips] add image build for ALL5002

add image build for ALL5002

Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32814

8 years ago[ramips] add support for Allnet ALL5002 to kernel
John Crispin [Tue, 24 Jul 2012 20:37:56 +0000 (20:37 +0000)]
[ramips] add support for Allnet ALL5002 to kernel

support ALL5002 in ramips/rt305x branch of the kernel.

Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32813

8 years ago[ramips] uart_clk on Rt3352F is always 40MHz
John Crispin [Tue, 24 Jul 2012 20:37:50 +0000 (20:37 +0000)]
[ramips] uart_clk on Rt3352F is always 40MHz

Currently, sys_clk/10 is used which is just wrong.
cpu_clk/10 would work for systems with 400MHz CPU clock.

Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 32812

8 years ago[package] orion_wdt is also available on kirkwood
Florian Fainelli [Tue, 24 Jul 2012 19:43:58 +0000 (19:43 +0000)]
[package] orion_wdt is also available on kirkwood

SVN-Revision: 32811

8 years ago[omap24xx] move omap specific modules to modules.mk
Florian Fainelli [Tue, 24 Jul 2012 19:43:54 +0000 (19:43 +0000)]
[omap24xx] move omap specific modules to modules.mk

SVN-Revision: 32810