John Crispin [Wed, 26 Nov 2014 08:59:49 +0000 (08:59 +0000)]
target.mk: add default packages for NAS device-type
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43387
John Crispin [Wed, 26 Nov 2014 08:59:41 +0000 (08:59 +0000)]
kernel: unset CONFIG_ARM_CCN
oldconfig kept asking for that config symbol...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43386
John Crispin [Wed, 26 Nov 2014 08:59:32 +0000 (08:59 +0000)]
ar71xx: add support for TP-LINK CPE210/220/510/520
This adds support for the TP-LINK CPE210/220/510/520 (Pharos series). These
devices are very similar to the Ubiquiti NanoStations, but with better specs:
faster CPU, more RAM, 2x2 MIMO.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 43385
John Crispin [Wed, 26 Nov 2014 08:59:22 +0000 (08:59 +0000)]
firmware-utils: add new tool tplink-safeloader for the new TP-LINK Pharos devices (CPE210/220/510/520)
The new TP-LINK Pharos series uses a new bootloader, the "TP-LINK Safeloader".
It uses an advanced firmware image format, containing an image partition table
and a flash partition table (and image partitions are mapped to the
corresponding flash partitions). The exact image format is documented in the
source code.
Furthermore, the bootloader expects the kernel image as an ELF executable.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 43384
John Crispin [Wed, 26 Nov 2014 08:59:17 +0000 (08:59 +0000)]
mtd: fix 2 compiler warnings
mtd.c:544:7: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘ssize_t’ [-Wformat]
mtd.c:602:1: warning: label ‘done’ defined but not used [-Wunused-label]
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43383
Imre Kaloz [Wed, 26 Nov 2014 08:28:22 +0000 (08:28 +0000)]
[ar71xx]: Netgear R6100 support
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 43382
Felix Fietkau [Tue, 25 Nov 2014 20:34:08 +0000 (20:34 +0000)]
uqmi: update to the latest version, also set 802.3 data format via the WDA service
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43381
Jonas Gorski [Tue, 25 Nov 2014 19:07:02 +0000 (19:07 +0000)]
brcm63xx: uci-defaults: network: move DSL-274x1 F1 to right section
The cpu port is at 8, not 5.
Fixes #18406.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43379
Jonas Gorski [Tue, 25 Nov 2014 19:06:51 +0000 (19:06 +0000)]
brcm63xx: unify dt image generation
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 43378
Jonas Gorski [Tue, 25 Nov 2014 19:06:43 +0000 (19:06 +0000)]
brcm63xx: move rsa signature to additional options
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 43377
Jonas Gorski [Tue, 25 Nov 2014 19:06:38 +0000 (19:06 +0000)]
brcm63xx: fix image generation
This fixes build issues introduced on r43361.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 43376
Imre Kaloz [Mon, 24 Nov 2014 22:09:47 +0000 (22:09 +0000)]
[generic/3.18]: rename overlayfs' symbol
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 43375
John Crispin [Mon, 24 Nov 2014 20:39:48 +0000 (20:39 +0000)]
ralink: fix pci reset patch
sorry, forgot to make target/update before commiting the last patch
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43374
John Crispin [Mon, 24 Nov 2014 19:14:29 +0000 (19:14 +0000)]
procd: fix/clean some conditions in nand.sh
1) nand_upgrade_tar: use a simpler condition that matches if () { }
logic and fix check of $kernel_length variable
2) nand_do_upgrade_stage2: use case, otherwise one could believe we
always call nand_upgrade_tar
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43373
John Crispin [Mon, 24 Nov 2014 19:14:17 +0000 (19:14 +0000)]
procd: document nand.sh a bit
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43372
John Crispin [Mon, 24 Nov 2014 19:12:46 +0000 (19:12 +0000)]
mpc85xx: fix missing dts target for kernel 3.14
With kernel 3.14 dts target p1010rdb was renamed to p1010rdb-pa.
To maintain compatibility define p1010rdb-pa as new standard and
copy p1010rdb.dts to p1010rdb-pa.dts under 3.10.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43371
John Crispin [Mon, 24 Nov 2014 19:12:35 +0000 (19:12 +0000)]
ralink: add proper reset of pci core
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43370
John Crispin [Mon, 24 Nov 2014 19:12:19 +0000 (19:12 +0000)]
imx6: make the default config bootable on ventana
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43369
Felix Fietkau [Mon, 24 Nov 2014 17:18:32 +0000 (17:18 +0000)]
fstools: update to the latest version, fixes overlayfs mount on 3.18
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43368
Felix Fietkau [Mon, 24 Nov 2014 17:13:54 +0000 (17:13 +0000)]
mac80211: fix a crash on getting the channel in WDS AP mode (#18400)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43367
Imre Kaloz [Mon, 24 Nov 2014 16:00:41 +0000 (16:00 +0000)]
[mvebu]: add initial 3.18 support
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 43366
Imre Kaloz [Mon, 24 Nov 2014 15:55:52 +0000 (15:55 +0000)]
[base-files]: fix sysupgrade on overlayfs v23+
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 43365
Jonas Gorski [Mon, 24 Nov 2014 14:44:46 +0000 (14:44 +0000)]
brcm63xx: do not build images for unsupported routers
If there is no board support in the kernel, it does not make sense to
build images for devices. So drop any images for board ids for which
there are nc corresponding board_info structs in the kernel.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43364
Jonas Gorski [Mon, 24 Nov 2014 14:44:40 +0000 (14:44 +0000)]
brcm63xx: refresh patches
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 43363
Jonas Gorski [Mon, 24 Nov 2014 14:44:33 +0000 (14:44 +0000)]
brcm63xx: Add DT support for SPW303V
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 43362
Jonas Gorski [Mon, 24 Nov 2014 14:44:28 +0000 (14:44 +0000)]
brcm63xx: Add DT support for DV-201AMR
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 43361
Jonas Gorski [Mon, 24 Nov 2014 14:44:23 +0000 (14:44 +0000)]
brcm63xx: Add DT support for RG100A
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 43360
Jonas Gorski [Mon, 24 Nov 2014 14:44:19 +0000 (14:44 +0000)]
brcm63xx: Add DT support for A226G/M
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 43359
Jonas Gorski [Mon, 24 Nov 2014 14:44:12 +0000 (14:44 +0000)]
brcm63xx: Add DT support for AGPF-S0
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 43358
Imre Kaloz [Mon, 24 Nov 2014 10:17:33 +0000 (10:17 +0000)]
[generic]: update .18 support for -rc6
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 43357
Felix Fietkau [Mon, 24 Nov 2014 09:33:48 +0000 (09:33 +0000)]
ar8216: Fix issue with autoneg being disabled under 3.14, revert 43332
Patch reverts 43332 which seems to cause issues with VLAN functionality.
Add a specific check to check whether ANEG is still enabled and re-enable
it if necessary. Disable generic phy soft reset for kernel >=3.16.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43356
Florian Fainelli [Mon, 24 Nov 2014 06:34:07 +0000 (06:34 +0000)]
arm64: add ARM 64-bits target
This target can be emulated using ARM's Foundation_V8 simulator
software or qemu-system-aarch64 using the command-line described in the
README file.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43355
Florian Fainelli [Mon, 24 Nov 2014 06:33:34 +0000 (06:33 +0000)]
libbsd: add support for aarch64
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43354
Florian Fainelli [Mon, 24 Nov 2014 06:33:13 +0000 (06:33 +0000)]
aarch64: add initial support
Add initial support for the AArch64 architecture
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43353
Florian Fainelli [Mon, 24 Nov 2014 02:06:20 +0000 (02:06 +0000)]
eglibc: enforce use of autoconf-2.69
Since we updated autoconf in r42855 we also need to enforce its use
while building eglibc to allow it to build successfully.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43352
Felix Fietkau [Sun, 23 Nov 2014 22:53:14 +0000 (22:53 +0000)]
libubox: fix a variable handling regression in jshn
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43351
Felix Fietkau [Sun, 23 Nov 2014 20:10:07 +0000 (20:10 +0000)]
libubox: update to the latest version, adds some jshn optimizations
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43350
Felix Fietkau [Sun, 23 Nov 2014 20:10:02 +0000 (20:10 +0000)]
lzo: disable unaligned access for everything except x86
Fixes issues on ARM
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43349
Felix Fietkau [Sun, 23 Nov 2014 20:09:56 +0000 (20:09 +0000)]
busybox: turn on BUSYBOX_DEFAULT_FEATURE_SH_NOFORK to slightly improve performance
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43348
Felix Fietkau [Sun, 23 Nov 2014 16:27:19 +0000 (16:27 +0000)]
ar71xx: merge changes from 3.10 that were forgotten for 3.14
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43347
Felix Fietkau [Sun, 23 Nov 2014 16:07:00 +0000 (16:07 +0000)]
netifd: update to the latest version, fixes issues when changing a bridge member from a vlan to its base device (#18351)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43346
Felix Fietkau [Sun, 23 Nov 2014 14:16:47 +0000 (14:16 +0000)]
hostapd: fix build error on some variants with CONFIG_WPA_RFKILL_SUPPORT=y (#17765)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43345
Felix Fietkau [Sun, 23 Nov 2014 13:54:28 +0000 (13:54 +0000)]
ar71xx: remove linux 3.10 support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43344
Felix Fietkau [Sun, 23 Nov 2014 13:54:22 +0000 (13:54 +0000)]
ar71xx: switch to linux 3.14
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43343
Felix Fietkau [Sun, 23 Nov 2014 12:53:35 +0000 (12:53 +0000)]
ath9k: fix some ar913x irq handling issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43342
Jonas Gorski [Sat, 22 Nov 2014 12:25:52 +0000 (12:25 +0000)]
brcm63xx: move board compatible strings into a table
Move compatible strings from board structs into separate table. This
allows for several board compatibles to match to the same board in case
e.g. only the flash size / partitions differ.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43341
Felix Fietkau [Fri, 21 Nov 2014 22:29:48 +0000 (22:29 +0000)]
mac80211: fix a crash on using VHT rates
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43340
Felix Fietkau [Fri, 21 Nov 2014 20:38:14 +0000 (20:38 +0000)]
hostapd: switch dependency from mac80211 to cfg80211
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43339
Zoltan Herpai [Fri, 21 Nov 2014 18:49:56 +0000 (18:49 +0000)]
sunxi: add config for 3.18
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 43338
Zoltan Herpai [Fri, 21 Nov 2014 18:42:43 +0000 (18:42 +0000)]
sunxi: add initial 3.18 support
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
SVN-Revision: 43337
Rafał Miłecki [Thu, 20 Nov 2014 22:15:21 +0000 (22:15 +0000)]
brcm47xx: add support for Netgear WGR614 V10
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43336
Felix Fietkau [Thu, 20 Nov 2014 20:27:36 +0000 (20:27 +0000)]
mt76: add new mediatek 802.11ac driver
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43335
Felix Fietkau [Thu, 20 Nov 2014 15:19:15 +0000 (15:19 +0000)]
ar8216: Use generic hw_init from ar8236 for ar8216 too
We should make sure that also for ar8216 hw gets initialized.
For ar8216 hw_init is a dummy currently. The hw_init used for ar8236
should be generic enough to be usable with ar8216 too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43334
Felix Fietkau [Thu, 20 Nov 2014 15:19:04 +0000 (15:19 +0000)]
ar8216: simplify PHY fixup/init
Move the PHY fixup call to the PHY init loop.
Use ar8xxx_has_gige in the PHY init instead of passing the gigE
capability via function parameter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43333
Felix Fietkau [Wed, 19 Nov 2014 20:18:01 +0000 (20:18 +0000)]
ar8216: use genphy_config_aneg also for PHY 0
Kernel 3.14 introduced a switch reset in phy_init_hw in drivers/net/phy
causing BMCR_ANENABLE to get cleared.
Due to the fact that ar8xxx_phy_config_aneg does nothing for
PHY 0 autonegatiation support remains disabled.
This can cause ports to operate at 10MBit/half-duplex only.
Fix this by calling genphy_config_aneg for PHY 0 too as
genphy_config_aneg sets BMCR_ANENABLE if it's not yet set.
Fixes: ticket 17800
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43332
Felix Fietkau [Wed, 19 Nov 2014 20:17:52 +0000 (20:17 +0000)]
ar8216: factor out PHY init code into a generic function
PHY init code in the switch-specific hw_init functions is mainly
identical. Factor it out into a generic ar8xxx_phy_init function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43331
Felix Fietkau [Wed, 19 Nov 2014 20:17:43 +0000 (20:17 +0000)]
ar8216: introduce fixup_phys callback in ar8xxx_chip
Move phy fixup code from the chip-specific hw_init functions into a
fixup_phys callback.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43330
Felix Fietkau [Wed, 19 Nov 2014 20:17:37 +0000 (20:17 +0000)]
ar8216: after a switch reset poll until BCMR_RESET is cleared
Currently there is a fixed 1000ms wait time after the switch was reset.
Most if not all switches need much less time to perform a reset.
Therefore replace the fixed wait time with polling for BMCR_RESET to
be cleared.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43329
Felix Fietkau [Wed, 19 Nov 2014 20:17:30 +0000 (20:17 +0000)]
ar8216: introduce global constant for number of PHYs
All supported switches have 5 PHYs. Currently partially 5 is hardcoded
and partially switch-specific constants exist.
Replace them with a global constant.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43328
Felix Fietkau [Wed, 19 Nov 2014 20:17:24 +0000 (20:17 +0000)]
procd: update to the latest version, fixes ubus service list
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43327
Felix Fietkau [Wed, 19 Nov 2014 20:17:08 +0000 (20:17 +0000)]
mac80211: try to get interface addresses from wiphy sysfs 'addresses' if no mask is set
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43326
Felix Fietkau [Wed, 19 Nov 2014 20:17:01 +0000 (20:17 +0000)]
mac80211: add an intermediate software queueing implementation
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43325
Felix Fietkau [Wed, 19 Nov 2014 20:16:55 +0000 (20:16 +0000)]
mac80211: add support for passing sta rate table updates to the driver
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43324
Felix Fietkau [Wed, 19 Nov 2014 20:16:50 +0000 (20:16 +0000)]
build: allow AutoLoad and AutoProbe to specify modules not included in the package
On out-of-tree modules depending on other out-of-tree modules from a
different tree, module dependencies are not filled properly.
This change helps with adding those dependencies in the AutoLoad call
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43323
Rafał Miłecki [Wed, 19 Nov 2014 17:35:24 +0000 (17:35 +0000)]
[PATCH] brcm47xx: mtd: bcm47xxpart: lower minimal blocksize to 4Ki (from 64Ki)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43322
John Crispin [Wed, 19 Nov 2014 14:09:19 +0000 (14:09 +0000)]
ixp4xx: Don't overwrite memory in wg302v1_fixup()
wg302v1_fixup() looks for the ATAG_CMDLINE atag, it doesn't find it and
so it takes the last atag in the list and overwrites non allocated
memory.
The side effects are corrupted vital data and a kernel that doesn't
boot. More details here https://dev.openwrt.org/ticket/18356
The fix appends the fixup to the command line and updates the atag only
when it finds it.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
SVN-Revision: 43320
John Crispin [Wed, 19 Nov 2014 14:09:10 +0000 (14:09 +0000)]
gemini: add basic nas4220 board support
Few notes:
- redboot partitions are unusable
- redboot declares only 16M of RAM, hence the mem arg in cmdline and separate kernel config
- boots fine but only ethernet works for now
- split wiliboard and raidsonic boards into different subtargets
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 43319
John Crispin [Wed, 19 Nov 2014 14:09:01 +0000 (14:09 +0000)]
keernel: Fixed dependencies in netfilter modules introduced with 3.18 kernel
Building current trunk with 3.18 kernel fired some errors like 'missed
dependancy of module XXX from library kmod_YYY.ko'. These patch fixes 3
of such issues which are critical to have a successful build.
Signed-off-by: Alexey N Vinogradov <a.n.vinogradov@gmail.com>
SVN-Revision: 43318
John Crispin [Wed, 19 Nov 2014 13:49:54 +0000 (13:49 +0000)]
uboot-envtools: add carambola2 support
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 43317
Jonas Gorski [Wed, 19 Nov 2014 12:42:00 +0000 (12:42 +0000)]
kernel: remove gpio-pwm kmod definition
r37490 removed the actual driver but left the kmod definition intact,
causing the build system hapily creating an empty package for it.
Remove it also to not make it seem as if it still exists.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43316
Jonas Gorski [Wed, 19 Nov 2014 12:17:37 +0000 (12:17 +0000)]
base-files: supress errors from ldd
ldd might be called for shell scrips during sysupgrade, causing it to
complain that they are not a dynamic executables.
This is a harmless error, so supress it to avoid confusing about them
being serious ones.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43315
Jonas Gorski [Wed, 19 Nov 2014 12:17:34 +0000 (12:17 +0000)]
toolchain: musl: fix symlink for ldd
ld-musl-*.so* is a symlink "broken" for the hostsystem, so wildcard
will skip it, causing LD_MUSL_NAME to empty and the ldd symlink pointing
to ../../lib directly.
This causes sysupgrade failing to copy any linked libaries and
consequently failing to run anything after switching to ram disk.
Fix this by creating a symlink directly pointing to where ld-musl-*.so*
points to.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43314
John Crispin [Wed, 19 Nov 2014 09:21:12 +0000 (09:21 +0000)]
nf_conntrack_rtsp: update to latest version
Update nf_conntrack_rtsp to latest version based on http://mike.it-loops.com/rtsp/ (rtsp-module-3.7-v2.tar.gz).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 43311
John Crispin [Wed, 19 Nov 2014 09:21:07 +0000 (09:21 +0000)]
uqmi: update to latest git HEAD
* fixes a bug in multipart sms
* adds a new call to read the sim phone number (partially functioanl)
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43310
John Crispin [Wed, 19 Nov 2014 09:21:02 +0000 (09:21 +0000)]
musl: add getopt support for non-option arguments
musl libc doesn't support the GNU getopt extension to parse non-option
arguments when the optstring starts with '-'.
This extension is used by some utilities, notably iptables, that
currently return with errors even with perfectly valid invocations.
The patch adds the code needed by getopt.c and getopt_long.c to
implement that extension.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
SVN-Revision: 43309
John Crispin [Wed, 19 Nov 2014 09:20:55 +0000 (09:20 +0000)]
mpc85xx: add 3.14 kernel support for mpc85xx platform
This patch adds 3.14 kernel support for the mpc85xx platform.
Works fine here with a TL-WDR4900 which seems to be the only
supported device using this platform.
There might be differences depending on HW version, therefore
I'd ask others to test too.
Changes to 3.10
missing config options added to 3.14 config file
patch 001: rebased
patch 100: rebased
patch 110: rebased
patch 120: rebased
patch 130: rebased
patch 140: minor adjustment
patch 200: removed, change went upstream
patch 210: rebased
patch 220: removed, change went upstream
patch 750: new, fixes an issue with ethernet port autoneg being
disabled due to changes in kernel phy handling
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 43308
John Crispin [Wed, 19 Nov 2014 09:20:47 +0000 (09:20 +0000)]
ar71xx: Added support for D-link DHP-1565 rev. A1
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
SVN-Revision: 43307
John Crispin [Wed, 19 Nov 2014 09:20:18 +0000 (09:20 +0000)]
ar71xx: fix switch configuration in Ubiquiti UAP Pro
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 43306
John Crispin [Wed, 19 Nov 2014 09:20:12 +0000 (09:20 +0000)]
ralink: various fixes to the wm8960 setup code
still no sound but the codec is properly detected now, powers up and i can hear
noise on the speakers.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43305
John Crispin [Wed, 19 Nov 2014 09:20:02 +0000 (09:20 +0000)]
ralink: make the dmaengine driver compile under 3.14
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43304
John Crispin [Wed, 19 Nov 2014 09:19:57 +0000 (09:19 +0000)]
ralink: fix tx vlan offload and hardware status
hardware status and tx vlan offload support on all targets
except rt5350. so i modify the IS_ENABLE condition only for
mt7621.
support mt7621 hardware status reference by SDK. but i don't
have mt7621. if not work just set mt7621 FE_REG_FE_COUNTER_BASE
to 0 to let software count.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43303
John Crispin [Wed, 19 Nov 2014 09:19:49 +0000 (09:19 +0000)]
ralink: support netconsole
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43302
John Crispin [Wed, 19 Nov 2014 09:19:43 +0000 (09:19 +0000)]
ralink: improve tx vlan offload
hardware tx vlan offload only support max 16 vids
now use add/delete vlan interface to update vlan id table
when duplicate vlan id index detect.
disable hardware tx vlan offload support.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43301
John Crispin [Wed, 19 Nov 2014 09:19:38 +0000 (09:19 +0000)]
ralink: merge the mt7620a/n subtargets
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43300
Steven Barth [Wed, 19 Nov 2014 08:31:13 +0000 (08:31 +0000)]
netifd: fix race, expose config options
Thanks to Hans Dedecker
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 43299
Felix Fietkau [Tue, 18 Nov 2014 22:20:50 +0000 (22:20 +0000)]
mac80211: fix a crash bug in minstrel_ht
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43298
Felix Fietkau [Tue, 18 Nov 2014 22:20:45 +0000 (22:20 +0000)]
mac80211: add support for reporting tx status without attached skb
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43297
Felix Fietkau [Tue, 18 Nov 2014 22:20:37 +0000 (22:20 +0000)]
mac80211: enable minstrel_ht VHT support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43296
Jonas Gorski [Tue, 18 Nov 2014 15:19:46 +0000 (15:19 +0000)]
base-files: properly fix copying ld*.so with eglibc
r36107 ("base-files: sysupgrade fail with eglibc") tried to fix
sysupgrade by changing the ld-soname to what is expected, but only
fixed MIPS while breaking ARM.
The underlying issue is that the ld.so name varies widely across
different architectures for eglibc:
eglibc-2.19-r25243$ grep -r "ld-soname :=" . | awk '{ print $3 }' | sort -u
ld64.so.1
ld64.so.2
ld-linux-aarch64_be.so.1
ld-linux-aarch64.so.1
ld-linux-armhf.so.3
ld-linux-mipsn8.so.1
ld-linux.so.2
ld-linux.so.3
ld-linux-x32.so.2
ld-linux-x86-64.so.2
ld.so.1
Instead of adding each different soname to check for and copy it,
replace the awk script with a sed script to extract it properly and
drop the hardcoded so-name.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43295
Steven Barth [Tue, 18 Nov 2014 09:40:39 +0000 (09:40 +0000)]
odhcp6c: be less verbose by default, increase musl compatibility
SVN-Revision: 43294
John Crispin [Mon, 17 Nov 2014 21:58:30 +0000 (21:58 +0000)]
ralink: set ralink_soc on mt7621
sdhci failed to init because of this
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43293
John Crispin [Mon, 17 Nov 2014 16:27:48 +0000 (16:27 +0000)]
ralink: fix pcie reset
some old mt7620a uboots dont reset the pcie core properly. work around this
issue in the kernel driver.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43292
John Crispin [Mon, 17 Nov 2014 14:30:42 +0000 (14:30 +0000)]
kernel/modules: use crc32c_generic.ko instead of crc32c.ko
Starting from kernel version 3.15, the crc32c module was renamed to
crc32c_generic.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43291
John Crispin [Mon, 17 Nov 2014 14:30:19 +0000 (14:30 +0000)]
kernel/modules: location of usb-common.ko changed
usb-common.ko was moved to drivers/usb/common starting from kernel 3.16
by upstream commit
f4cbd33fd5f0587910fa9db403a1b42f1cabf820
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43290
John Crispin [Mon, 17 Nov 2014 08:34:03 +0000 (08:34 +0000)]
kernel: add the ubifs EOF marker support to 3.14 kernel
Without this patch the UBIFS driver is unable to attach to the mtd
storage and mount the root FS.
Fixes a kernel panic with Netgear WNDR4300/3700v4 devices.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
SVN-Revision: 43287
Felix Fietkau [Sun, 16 Nov 2014 12:26:53 +0000 (12:26 +0000)]
ramips: disable 2.4 ghz on 802.11ac wifi on WHR-1166D
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43283
Felix Fietkau [Sun, 16 Nov 2014 12:26:47 +0000 (12:26 +0000)]
ramips: use mediatek,mtd-eeprom instead of ralink for mt76
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43282
Felix Fietkau [Sun, 16 Nov 2014 11:39:19 +0000 (11:39 +0000)]
ramips: fix default config breakage on whr-1166d
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43281
Felix Fietkau [Sun, 16 Nov 2014 11:39:14 +0000 (11:39 +0000)]
trace-cmd: update to v2.4
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43280
Felix Fietkau [Sun, 16 Nov 2014 11:39:07 +0000 (11:39 +0000)]
mac80211: fix VHT rate selection
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 43279
projects / openwrt / svn-archive / archive.git / log