po: add missing po files

[project/luci.git] / po / en / olsr.po

diff --git a/po/en/olsr.po b/po/en/olsr.po
index 9d4e9aa1d2cdb443e3d84c2b08ffce67b428287b..db99e8c1d2a8c9912409bc1ea63198ccf71ed128 100644 (file)
--- a/po/en/olsr.po
+++ b/po/en/olsr.po
@@ -25,9 +25,21 @@ msgstr "Active host net announcements"
 msgid "Advanced Settings"
 msgstr ""
 
+msgid "Allow gateways with NAT"
+msgstr ""
+
+msgid "Allow the selection of an outgoing ipv4 gateway with NAT"
+msgstr ""
+
+msgid "Announce uplink"
+msgstr ""
+
 msgid "Announced network"
 msgstr "Announced network"
 
+msgid "Both values must use the dotted decimal notation."
+msgstr ""
+
 msgid "Broadcast address"
 msgstr ""
 
@@ -52,6 +64,11 @@ msgstr ""
 msgid "Enable"
 msgstr ""
 
+msgid ""
+"Enable SmartGateway. If it is disabled, then all other SmartGateway "
+"parameters are ignored. Default is \"no\"."
+msgstr ""
+
 msgid "Enable this interface."
 msgstr ""
 
@@ -106,6 +123,12 @@ msgstr "Hello interval"
 msgid "Hello validity time"
 msgstr "Hello validity time"
 
+msgid "Hna4"
+msgstr ""
+
+msgid "Hna6"
+msgstr ""
+
 msgid "Hops"
 msgstr ""
 
@@ -157,6 +180,10 @@ msgid ""
 "multicast."
 msgstr ""
 
+msgid ""
+"IPv6 network must be given in full notation, prefix must be in CIDR notation."
+msgstr ""
+
 msgid "IPv6 source"
 msgstr ""
 
@@ -166,6 +193,9 @@ msgid ""
 "of a not-linklocal interface IP."
 msgstr ""
 
+msgid "IPv6-Prefix of the uplink"
+msgstr ""
+
 msgid ""
 "If the route to the current gateway is to be changed, the ETX value of this "
 "gateway is multiplied with this value before it is compared to the new one. "
@@ -174,6 +204,10 @@ msgid ""
 "with the etx_ffeth metric!<br />Defaults to \"1.0\"."
 msgstr ""
 
+msgid ""
+"If this Node uses NAT for connections to the internet. Default is \"yes\"."
+msgstr ""
+
 msgid "Interface"
 msgstr ""
 
@@ -397,9 +431,6 @@ msgid ""
 "really slow. In this case disable it here."
 msgstr ""
 
-msgid "Routen"
-msgstr ""
-
 msgid "Routes"
 msgstr ""
 
@@ -424,6 +455,14 @@ msgstr ""
 msgid "Source address"
 msgstr ""
 
+msgid ""
+"Specifies the speed of the uplink in kilobits/s. First parameter is "
+"upstream, second parameter is downstream. Default is \"128 1024\"."
+msgstr ""
+
+msgid "Speed of the uplink"
+msgstr ""
+
 msgid "State"
 msgstr ""
 
@@ -469,10 +508,14 @@ msgid ""
 "It can have a value between 1 and 65535."
 msgstr ""
 
-msgid "Timing and Validity"
+msgid ""
+"This can be used to signal the external IPv6 prefix of the uplink to the "
+"clients. This might allow a client to change it's local IPv6 address to use "
+"the IPv6 gateway without any kind of address translation. The maximum prefix "
+"length is 64 bits. Default is \"::/0\" (no prefix)."
 msgstr ""
 
-msgid "Topologie"
+msgid "Timing and Validity"
 msgstr ""
 
 msgid "Topology"
@@ -489,6 +532,9 @@ msgstr "Unable to connect to the OLSR daemon!"
 msgid "Uplink"
 msgstr ""
 
+msgid "Uplink uses NAT"
+msgstr ""
+
 msgid "Use hysteresis"
 msgstr "Use hysteresis"
 
@@ -498,6 +544,11 @@ msgstr ""
 msgid "WLAN"
 msgstr ""
 
+msgid ""
+"Warning: kmod-ipip is not installed. Without kmod-ipip SmartGateway will not "
+"work, please install it."
+msgstr ""
+
 msgid "Weight"
 msgstr ""
 
@@ -511,5 +562,11 @@ msgid ""
 "instead."
 msgstr ""
 
+msgid ""
+"Which kind of uplink is exported to the other mesh nodes. An uplink is "
+"detected by looking for a local HNA of 0.0.0.0/0, ::ffff:0:0/96 or 2000::/3. "
+"Default setting is \"both\"."
+msgstr ""
+
 msgid "Willingness"
 msgstr "Willingness"